Home

TP-Link TL-SG3210 V2 CLI Reference Guide

1. IEEE 802 1Q VLAN ID ranging from 1 to 4094 ipv6 addr Specify the IPv6 source address Command Mode Global Configuration Mode 223 Example Specify the source address which sends the Query message as fe80 1234 on VLAN 2 TL SG3424 config ipv6 mld snooping querier vlan 2 query source fe80 1234 ipv6 mid snooping filter global ipv6 Description The ipv6 mld snooping filter command is used to configure the multicast group filter entries in the format of ip range To disable the filter entry please use no ipv6 mld snooping filter command Syntax ipv6 mld snooping filter filter id start ipv6 end ipv6 no ipv6 mld snooping filter filter id Parameter filter id Specify the filter ID ranging from 1 to 30 start ipv6 Start IPv6 multicast address of the filter entry end ipv6 End IPv6 multicast address of the filter entry Command Mode Global Configuration Mode Example Create filter entry with filter ID as 2 start IP as ff80 1234 and end IP as ff80 1235 TL SG3424 config ipv6 mid snooping filter 2 ff80 1234 ff80 1235 mid snooping filter interface Description The ipv6 mld snooping filter command is used to enable the filter function on the interface To disable the filter function please use no ipv6 mld snooping filter command Syntax ipv6 mld snooping filter no ipv6 mld snooping filter Command Mode Interface Configuration Mode 224 Example Enable filter f
2. TL SG3424 config spanning tree hold count 8 195 spanning tree max hops Description The spanning tree max hops command is used to configure the maximum number of hops that occur in a specific region before the BPDU is discarded To return to the default configurations please use no spanning tree max hops command Syntax spanning tree max hops value no spanning tree max hops Parameter value The maximum number of hops that occur in a specific region before the BPDU is discarded ranging from 1 to 40 in hop By default it is 20 Command Mode Global Configuration Mode Example Configure the max hops of STP as 30 TL SG3424 config spanning tree max hops 30 spanning tree bpdufilter Description The spanning tree bpdufilter command is used to enable the BPDU filter function for a port With the function enabled the port can be prevented from receiving and sending any BPDU packets To disable the BPDU filter function please use no spanning tree bpdufilter command Syntax spanning tree bpdufilter no spanning tree bpdufilter Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the BPDU filter function for port 2 196 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if spanning tree bpdufilter spanning tree bpduguard Description The spanning tree bpduguard command is used to enable the BPDU protect f
3. BEE Password TL SG3424 gt _ Figure 1 16 Enter into the User EXEC Mode 1 When entering enable command to access Privileged EXEC Mode you are required to give the password 123 you have set through Console port connection Delt Password iT L SG3424 gt enable Password iT L SG3424 Figure 1 17 Enter into the Privileged EXEC Mode 10 Now you can manage your switch with CLI commands through Telnet connection Note You can refer to Chapter 9 User Manage Commands for detailed commands information of the Telnet connection configuration 1 1 4 Logon by SSH To log on by SSH a Putty client software is recommended There are two authentication modes to set up an SSH connection Password Authentication Mode It requires username and password which are both admin by default Key Authentication Mode It requires a public key for the switch and a private key for the SSH client software You can generate the public key and the private key through Putty Key Generator Note Before SSH login please follow the steps shown in Figure 1 16 to enable the SSH function through console connection TPLINK HyperTerminal File Edit View Call Transfer Help De 6 28 TL SG3424 gt enable Gn Enter the Privileged EXEC Mode password Password TL G3424 config TL G3424 config ip ssh server o Enable SSH function TL SG3424 config H Figure 1 16 Enable SSH function gt Pa
4. The neighbor LACP information Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the internal LACP information of EtherChannel Group 1 TL SG3424 config show lacp 1 internal show lacp sys id Description The show lacp sys id command is used to display the LACP system priority globally Syntax show lacp sys id Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LACP system priority TL SG3424 config show lacp sys id 50 Chapter9 User Manage Commands User Manage Commands are used to manage the user s logging information by Web Telnet or SSH so as to protect the settings of the switch from being randomly changed user name password Description The user name command is used to add a new user or modify the existed users information To delete the existed users please use no user name command This command uses the symmetric encryption Syntax user name name privilege admin guest password 0 password 7 encrypted password y no user name name Parameter name Type a name for users login which contains 16 characters at most composed of digits English letters and under dashes only admin guest Access level Admin means that you can edit modify and view all the settings of different functions Guest means that you can only view the settings without the right to edit and modify It is admin by de
5. Window Appearance Behaviour Translation Selection Colours Connection Data Proxy Telnet Rlogin SSH Kex TTY x11 Tunnels Bugs Options controlling SSH authentication C Bypass authentication entirely SSH 2 only Authentication methods Attempt authentication using Pageant C Attempt TIS or CryptoCard auth SSH 1 Attempt keyboard interactive auth SSH 2 Authentication parameters C Allow agent forwarding C Allow attempted changes of username in SSH 2 E Program Files private ppk Figure 1 23 Load the Private Key 15 After successful authentication please enter the login user name If you log on to the switch without entering password it indicates that the key has been successfully loaded Y 192 168 0 1 Putt admin entication required ey rsa key 20140127 Figure 1 24 Log on the Switch 1 2 CLI Command Modes The CLI is divided into different command modes User EXEC Mode Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode and VLAN Configuration Mode Interface Configuration Mode can also be divided into Interface gigabitEthernet Interface link aggregation and some other modes which is shown as the following diagram Interface Configuration Mode Interface gigabitEthernet User EXEC Mode Interface link aggregation Interface range gigabitEthernet password Interface range link aggregation Interface vlan Privileged EXEC Glob
6. broadcast storm Interface range link aggregation Configure parameters for multi trunks Interface vlan Configure parameters for the vlan port 17 e Vian Configuration Mode In this mode users can create a VLAN and add a specified port to the VLAN 3 Some commands are global that means they can be performed in all modes e show Displays all information of switch for example statistic information port information VLAN information e history Displays the commands history 1 3 Security Levels This switch s security is divided into two levels User level and Admin level User level only allows users to do some simple operations in User EXEC Mode Admin level allows you to monitor configure and manage the switch in Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode and VLAN Configuration Mode For logging on remotely by Telnet or SSH you need a username and password both admin by default to get the privilege to the User level Guest users are restricted to access the CLI Users can enter Privileged EXEC mode from User EXEC mode by using the enable command and entering a Privileged EXEC mode password Please connect to the switch by console port to configure the Privileged EXEC mode password For logging on by console port you can enter the User EXEC mode directly Users can enter Privileged EXEC mode from User EXEC mode by using the enable command In default case no password is neede
7. cir Telnet 192 168 0 1 x boooooseceneseooe User Access Login ssessennecscsneescade User admin Password T L SG3424 gt enable Password TL SG34248 Figure 1 12 Enter into the Privileged EXEC Mode gt Login Mode Firstly enter the Privileged EXEC Mode password set in 1 1 2 Configuring the Priviledged EXEC Mode Password and configure the Telnet login mode as login and the connection password and 456 in the prompted DOS screen shown in Figure 1 13 TPLINK HyperTerminal File Edit View Call Transfer Help De 29 E TL 63424 gt enable Password q TL G3424 config TL SG3424 config Hline vty 0 5 Enter the Privileged EXEC Mode password TL S63424 config line login lt Set login mode TL S63424 config line Hpassword 456 lt t CONNEC tioN password TL SG3424 config line exit TL SG3424 config H lt Connected 0 00 45 Auto detect 38400 8 N 1 Figure 1 13 Configure login mode Now you can logon by Telnet in login mode 1 Open Telnet and type telnet 192 168 0 1 in the command prompt shown as Figure 1 14 and press the Enter button icrosoft Windows XP Version 5 1 26001 lt C gt Copyright 1985 2881 Microsoft Corp C Documents and Settings Admin gt telnet 192 168 8 1_ Figure 1 14 Connecting to the Switch 2 You are prompted to enter the connection password 456 you have set through Console port connection and then you are in User EXEC Mode
8. log host Syntax show logging loghost index Parameter index The index of the log host whose configuration will be displayed ranging from 1 to 4 Display the configuration of all the log hosts by default Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the log host 2 TL SG3424 config show logging loghost 2 93 show logging buffer Description The show logging buffer command is used to display the log information in the log buffer according to the severity level Syntax show logging buffer level evel Parameter level Severity level There are 8 severity levels marked with values 0 7 The information of levels with priority not lower than the select level will display Display all the log information in the log buffer by default Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the log information from level O to level 5 in the log buffer TL SG3424 config show logging buffer level 5 show logging flash Description The show logging flash command is used to display the log information in the log file according to the severity level Syntax show logging flash level eve Parameter level Severity level There are 8 severity levels marked with values 0 7 The information of levels with priority not lower than the select level will display Display all the log information in the log file by def
9. media type sfp duplex Description The duplex command is used to configure the Duplex Mode for an Ethernet port To return to the default configuration please use no duplex command Syntax duplex full half no duplex Parameter full half The duplex mode of the Ethernet port There are two options full duplex mode default and half duplex mode Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the Duplex Mode as full duplex for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if duplex full 135 speed Description The speed command is used to configure the Speed Mode for an Ethernet port To return to the default configuration please use no speed command Syntax speed 10 100 1000 auto no speed Parameter 10 100 1000 auto The speed mode of the Ethernet port There are four options 10Mbps 100Mbps 1000Mbps and Auto negotiation mode default Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the Speed Mode as 100Mbps for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if speed 100 storm control broadcast Description The storm control broadcast command is used to enable the broadcast control function To disable the broadcast control function please use no storm cont
10. packet stat The related configuration information selected to display Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IGMP filter configuration of all ports TL SG3424 show ip igmp snooping interface gigabitEthernet filter Display the IGMP basic configuration of port 2 TL SG3424 show ip igmp snooping interface gigabitEthernet 1 0 2 basic config Display the IGMP packet statistics of ports 1 4 TL SG3424 show ip igmp snooping interface gigabitEthernet 1 0 1 4 packet stat show ip igmp snooping vian Description The show ip igmp snooping vlan command is used to display the VLAN configuration of IGMP snooping Syntax show ip igmp snooping vlan vian id Parameter vlan id The VLAN ID selected to display Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IGMP snooping configuration information of VLAN 2 211 TL SG3424 show ip igmp snooping vlan 2 show ip igmp snooping multi vlan Description The show ip igmp snooping multi vlan command is used to display the Multicast VLAN configuration Syntax show ip igmp snooping multi vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Multicast VLAN configuration TL SG3424 show ip igmp snooping multi vlan show ip igmp snooping groups Description The show ip igmp snooping groups command is used to display the information of all IGMP sno
11. Enable the automatic ipv6 address configuration function to obtain IPv6 address through the RA message when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 address ra 129 ipv6 address eui 64 Description This command is used to manually configure a global IPv6 address with an extended unique identifier EUI in the low order 64 bits on the interface Specify only the network prefix The last 64 bits are automatically computed from the switch MAC address To remove an EUI 64 IPv6 address from the interface please use the no ipv6 address eui 64 command Syntax ipv6 address pv6 addr eui 64 no ipv6 address pv6 addr eui 64 Parameter ipv6 addr Global IPv6 address with 64 bits network prefix for example 3ffe 1 64 Configuration Mode Interface Configuration Mode interface vlan Example Configure an EUI 64 global address on the interface with the network prefix 3ffe 1 64 TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 address 3ffe 1 64 eui 64 ipv6 address Description This command is used to manually configure a global IPv6 address on the interface To remove a global IPv6 address from the interface please use no ipv6 address command Syntax ipv6 address pv6 addr no ipv6 address pv6 addr Parameter ipv6 addr Global IPv6 address with network prefix for example 3ffe 1 64 130 Configuration Mode Interface
12. Global Configuration Mode Example Specify multicast VLAN as VLAN 2 TL SG3424 config ipv6 mld snooping multicast vlan vlan id 2 ipv6 mid snooping vlan Description The ipv6 mld snooping vlan command is used to enable MLD Snooping function on a specified VLAN To disable it please use no ipv6 mld snooping vlan command Syntax ipv6 mld snooping vlan vian id no ipv6 mld snooping vlan vian id Parameter vlan id The specified VLAN ID to enable MLD Snooping function ranging from 1 to 4094 Command Mode Global Configuration Mode Example Enable MLD Snooping function on VLAN 2 TL SG3424 config ipv6 mld snooping vlan 2 218 ipv6 mid snooping vlan router aging time Description The ipv6 mld snooping vlan router aging time command is used to specify router port aging time for a specified VLAN If this time is set to 0 then the global router port aging time will be used The default time is 0 To restore the default timer please use no ipv6 mld snooping vlan router aging time command Syntax ipv6 mld snooping vlan vian id router aging time timer no ipv6 mld snooping vlan vian id router aging time Parameter vlan id The specified IEEE 802 1Q VLAN ID ranging from 1 to 4094 timer Aging time of the router port in seconds ranging from O to 1000 Command Mode Global Configuration Mode Example Specify the router port aging time as 100 seconds in VLAN 2 TL SG3424 config ipv6 mld snooping vlan
13. Jun Jul Aug Sep Oct Nov Dec sday Day to start ranging from 1 to 31 Please mind that the number of days depends on the month stime Time to start in the format of hh mm emonth Month to end with the options Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec eday Day to end ranging from 1 to 31 Please mind that the number of days depends on the month etime Time to end in the format of hh mm offset Specify the time adding in minutes when Daylight Saving Time comes The value ranges from 1 to 1440 and the default value is 60 minutes It is optional Command Mode Global Configuration Mode Example Configure the DST start time as 00 00 am on April 1 the end time as 00 00 am on October 1 and the offset as 30 minutes TL SG3424 config system time dst date Apr 1 00 00 Oct 1 00 00 30 113 system time dst recurring Description The system time dst recurring command is used to specify the DST configuration in recurring mode This configuration is recurring in use The time period is restricted to be within one year Syntax system time dst recurring sweek sday smonth stime eweek eday emonth y etime y offset Parameter sweek Week to start with the options first second third fourth last sday Day to start with the options Sun Mon Tue Wed Thu Fri Sat smonth Month to start with options Jan F
14. MAC address VLAN and the connected Port number of the Host together which can be the condition for the ARP Inspection to filter the packets ip source binding Description The ip source binding command is used to bind the IP address MAC address VLAN ID and the Port number together manually You can manually bind the IP address MAC address VLAN ID and the Port number together in the condition that you have got the related information of the Hosts in the LAN To delete the IP MAC VID PORT entry from the binding table please use no ip source binding index command Syntax ip source binding hostname ip addr mac addr vlan vid interface gigabitEthernet port none arp detection forced source arp scanning dhcp snooping H no ip source binding index dx Parameter hostname The Host Name which contains 20 characters at most ip addr The IP Address of the Host mac addr The MAC Address of the Host vid The VLAN ID needed to be bound ranging from 1 to 4094 port The number of Ethernet port connected to the Host none arp detection The protect type for the entry arp detection indicates ARP detection none indicates applying none forced source The source of the binding entry can be specified as arp scanning or dhcp snooping It is multi optional idx The entry number needed to be deleted ranging from 1 to 200 You can use the show ip source binding command to ge
15. Rise Event which is the index of the corresponding event which will be triggered if the sampled value is larger than the Rising Threshold It ranges from 1 to 12 f hold The falling counter value that triggers the Falling Threshold alarm ranging from 1 to 65535 By default it is 100 f event Fall Event which is the index of the corresponding event which will be triggered if the sampled value is lower than the Falling Threshold It ranges from 1 to 12 a type Alarm Type with rise fall and all options Rise indicates that the alarm event will be triggered when the sampled value exceeds the Rising Threshold fall indicates that the alarm event will be triggered when the sampled value is under the Falling Threshold and all indicates that the alarm event will be triggered either the sampled value exceeds the Rising Threshold or is under the Falling Threshold By default the Alarm Type is all owner name The owner of the entry ranging from 1 to 16 characters By default it is monitor interval The alarm interval time ranging from 10 to 3600 in seconds By default it is 1800 Command Mode Global Configuration Mode 244 Example Configure the port of entries of 1 2 and 3 as port 2 the owners as owner1 and the alarm intervals as 100 seconds TL SG3424 config rmon alarm 1 3 interface gigabitEthernet 1 0 2 owner owner interval 100 show snmp server Description The show snmp server
16. SSL key to the switch from TFTP server Syntax ip http secure server download key ss key ip address p addr Parameter ssi key The name of the SSL key which is selected to download to the switch The length of the name ranges from 1 to 25 characters The key must be BASE64 encoded ip addr The IP address of the TFTP server Both IPv4 and IPv6 addresses are supported for example 192 168 0 1 or fe80 1234 Command Mode Global Configuration Mode 101 Example Download an SSL key named ssl key from TFTP server with the IP address of 192 168 0 146 TL SG3424 config ip http secure server download key ssl key ip address 192 168 0 146 Download an SSL key named ssl key from TFTP server with the IP address of fe80 1234 TL SG3424 config ip http secure server download key ssl key ip address fe80 1234 show ip http secure server Description The show ip http secure server command is used to display the global configuration of SSL Syntax show ip http secure server Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of SSL TL SG3424 config show ip http secure server 102 Chapter 17 MAC Address Commands MAC Address configuration can improve the network security by configuring the Port Security and maintaining the address information by managing the Address Table mac address table static Description The mac address table static command is used
17. Syntax ipv6 mld snooping router aging time timer no ipv6 mld snooping router aging time Parameter timer Specify the aging time in seconds ranging from 1 to 1000 Command Mode Global Configuration Mode 214 Example Specify MLD Snooping router port aging time as 100 seconds globally TL SG3424 config ipv6 mld snooping router aging time 100 ipv6 mid snooping member aging time Description The ipv6 mld snooping member aging time command is used to specify member port aging time globally The default aging time is 260 seconds To restore the default timer please use no ipv6 mid snooping member aging time command Syntax ipv6 mld snooping member aging time timer no ipv6 mld snooping member aging time Parameter timer Specify the aging time in seconds ranging from 200 to 1000 Command Mode Global Configuration Mode Example Specify MLD Snooping member port aging time as 100 seconds globally TL SG3424 config ipv6 mld snooping member aging time 100 ipv6 mid snooping report suppression Description The ipv6 mld snooping report suppression command is used to enable the Report message suppression function By default it is enabled To disable this function please use no ipv6 mld snooping report suppression command Syntax ipv6 mld snooping report suppression no ipv6 mld snooping report suppression Command Mode Global Configuration Mode Example Disable Report message suppression function
18. interface vlan Example Enable the IPv6 function when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 enable ipv6 address autoconfig Description This command is used to enable the automatic configuration of the ipv6 link local address The switch has only one ipv6 link local address which can be configured automatically or manually The general ipv6 link local address has the prefix as fe80 10 IPv6 routers cannot forward packets that have link local source or destination addresses to other links The autuconfigured ipv6 link local address is in EUI 64 format To verify the uniqueness of the link local address the manually configured ipv6 link local address will be deleted when the autoconfigured ipv6 link local address takes effect 127 Syntax ipv6 address autoconfig Configuration Mode Interface Configuration Mode interface vlan Example Enable the automatic configuration of the ipv6 link local address when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 address autoconfig ipv6 address link local Description The ipv6 address link local command is used to configure the system ipv6 link local address manually To delete the configured link local address please use no ipv6 address link local command Syntax ipv6 address pv6 addr link local no ipv6 address pv6 addr link local Parameter
19. ipv6 addr The link local address of the switch It should be a standardized IPv6 address with the prefix fe80 10 otherwise this command will be invalid Configuration Mode Interface Configuration Mode Interface vlan Example Configure the link local address as fe80 1234 when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 address fe80 1234 link local ipv6 address dhcp Description The ipv6 address dhcp command is used to enable the DHCPv 6 Client function When this function is enabled the switch will try to obtain IP from DHCPv6 128 server To delete the allocated IP from DHCPV6 server and disable the DHCPv6 Client function please use no ipv6 address dhcp command Syntax ipv6 address dhcp no ipv6 address dhcp Configuration Mode Interface Configuration Mode interface vian Example Enable the DHCP Client function when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 address dhcp ipv6 address ra Description This command is used to configure the switch s global IPv6 address according to the address prefix and other configuration parameters from its received RA Router Advertisement message To disable this function please use no ipv6 address ra command Syntax ipv6 address ra no ipv6 address ra Configuration Mode Interface Configuration Mode interface vian Example
20. log notify log notify owner owner name no rmon event index 242 Parameter index The index number of the event entry ranging from 1 to 12 You can only select one entry for each command user name The name of the User to which the event belongs ranging from 1 to 16 characters By default it is public descript The description of the event ranging from 1 to 16 characters By default it is empty type The event type with none log notify and both options None indicates no processing log indicates logging the event notify indicates sending trap messages to the management station and both indicates logging the event and sending trap messages to the management station owner name The owner of the event entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the user name of entry 1 2 3 and 4 as user1 the description of the event as description1 the type of event as log and the owner of the event as owner1 TL SG3424 config rmon event 1 4 user user1 description description1 type log owner owner1 rmon alarm Description The rmon alarm command is used to configure SNMP RMON Alarm Management To return to the default configuration please use no rmon alarm command Alarm Group is one of the commonly used RMON Groups RMON alarm management allows monitoring the specific alarm variables When the
21. 10 TL SG3424 config show vlan id 3 10 31 Chapter A MAC based VLAN Commands MAC based VLAN Virtual Local Area Network is the way to classify the VLANs based on MAC Address AMAC address corresponds to a VLAN ID The untagged packets and the priority tagged packets sourced from the MAC address will be tagged with this VLAN ID mac vlan mac address Description The mac vlan mac address command is used to create a MAC based VLAN entry To delete MAC based VLAN entry please use the no mac vlan mac address command Syntax mac vlan mac address mac addr vlan vian id description descript no mac vlan mac address mac addr Parameter mac addr MAC address in the format of XX XX XX XX XX XX vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 descript Give a description of the MAC based VLAN entry for identification which contains 8 characters at most Command Mode Global Configuration Mode Example Add an entry whose MAC address is 00 11 11 01 01 12 to VLAN 2 then name the MAC base entry as TP TL SG3424 config mac vlan mac address 00 11 11 01 01 12 vlan 2 description TP show mac vlan Description The show mac vlan command is used to display the information of the MAC based VLAN MAC address and VLAN ID can be used to filter the displayed information Syntax show mac vlan all mac address mac addr vlan vian id 32 Command Mode Privileged EXEC Mode and A
22. 194 Parameter forward time Forward Delay which is the time for the port to transit its state after the network topology is changed Forward Delay ranges from 4 to 30 in seconds and it is 15 by default Otherwise 2 Forward Delay 1 2 Max Age hello time Hello Time which is the interval to send BPDU packets and used to test the links Hello Time ranges from 1 to 10 in seconds and it is 2 by default Otherwise 2 Hello Time 1 lt Max Age max age The maximum time the switch can wait without receiving a BPDU before attempting to reconfigure ranging from 6 to 40 in seconds By default it is 20 Command Mode Global Configuration Mode Example Configure forward time hello time and max age for Spanning Tree as 16 seconds 3 seconds and 22 seconds respectively TL SG3424 config spanning tree timer forward time 16 hello time 3 max age 22 spanning tree hold count Description The spanning tree hold count command is used to configure the maximum number of BPDU packets transmitted per Hello Time interval To return to the default configurations please use no spanning tree hold count command Syntax spanning tree hold count value no spanning tree hold count Parameter value The maximum number of BPDU packets transmitted per Hello Time interval ranging from 1 to 20 in pps By default it is 5 Command Mode Global Configuration Mode Example Configure the hold count of STP as 8pps
23. 2 as 20 pps TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ip dhcp snooping limit rate 20 ip dhcp snooping decline Description The ip dhcp snooping decline command is used to enable the Decline Protect feature To disable the Decline Protect feature please use no ip dhcp snooping decline command 68 Syntax ip dhcp snooping decline no ip dhcp snooping decline Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the Decline Protect feature of port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ip dhcp snooping decline show ip source binding Description The show ip source binding command is used to display the IP MAC VID PORT binding table Syntax show ip source binding Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IP MAC VID PORT binding table TL SG3424 config show ip source binding show ip dhcp snooping Description The show ip dhcp snooping command is used to display the running status of DHCP Snooping Syntax show ip dhcp snooping 69 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the running status of DHCP Snooping TL SG3424 show ip dhcp snooping show ip dhcp snooping information Description The show ip dhcp snooping information command is used to display the Option 82 configuration
24. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the filter entries TL SG3424 config show ipv6 mld snooping filter show ipv6 mid snooping interface Description The show ipv6 mld snooping interface command is used to display the interface information of MLD Snooping Syntax show ipv6 mld snooping interface gigabitEthernet port Parameter port Specify the port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all of the interface information TL SG3424 config show ipv6 mld snooping interface show ipv6 mid snooping interface filter Description The show ipv6 mld snooping interface filter command is used to display the filter ids bounded to the interface Syntax show ipv6 mld snooping interface filter gigabitEthernet port Parameter port Specify the port number Command Mode Privileged EXEC Mode and Any Configuration Mode 229 Example Display all filter ids bounded to all interface TL SG3424 config show ipv6 mld snooping interface filter show ipv6 mid snooping querier Description The show ipv6 mld snooping querier command is used to display the Querier configuration of VLAN Syntax show ipv6 mld snooping querier vlan vian id Parameter vlan id The VLAN ID selected to display ranging from 1 to 4094 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all Querier info
25. Delete VLAN 2 TL SG3424 config no vlan 2 interface vian Description The interface vlan command is used to create VLAN Interface and enter Interface VLAN Mode To delete VLAN Interface please use no interface vlan command Syntax interface vlan vian id no interface vlan vian id 26 Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 Command Mode Global Configuration Mode Example Create VLAN Interface 2 TL SG3424 config interface vlan 2 name Description The name command is used to assign a description to a VLAN To clear the description please use no name command Syntax name descript no name Parameter descript String to describe the VLAN which contains 16 characters at most Command Mode VLAN Configuration Mode VLAN Example Specify the name of VLAN 2 as group1 TL SG3424 config vlan 2 TL SG3424 config vlan name group1 switchport mode Description The switchport mode command is used to configure the Link Type for the ports Syntax switchport mode access trunk general Parameter access trunk general Link Types There are three Link Types for the ports 27 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the Link Type of port 3 as trunk TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if switchport mode trunk switc
26. EXEC Mode and Any Configuration Mode 44 Example Display the global GVRP status TL SG3424 config show gvrp global show gvrp interface Description The show gvrp interface command is used to display the GVRP configuration information of all ports or a specified Ethernet port Syntax show gvrp interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the GVRP configuration information of all Ethernet ports TL SG3424 config show gvrp interface Display the GVRP configuration information of port 2 TL SG3424 config show gvrp interface gigabitEthernet 1 0 2 45 Chapter 8 Etherchannel Commands Etherchannel Commands are used to configure LAG and LACP function LAG Link Aggregation Group is to combine a number of ports together to make a single high bandwidth data path which can highly extend the bandwidth The bandwidth of the LAG is the sum of bandwidth of its member port LACP Link Aggregation Control Protocol is defined in IEEE802 3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner The switch can dynamically group similarly configured ports into a single logical link which will highly extend the bandwidth and flexibly balance the load channel group Description The channel group command is used to add a port to the EtherChannel Group and co
27. Example Enable IGMP Snooping function of port 3 203 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if ip igmp snooping ip igmp snooping immediate leave Description The ip igmp snooping immediate leave command is used to configure the Fast Leave function for port To disable the Fast Leave function please use no ip igmp snooping immediate leave command Syntax ip igmp snooping immediate leave no ip igmp snooping immediate leave Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the Fast Leave function for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if ip igmp snooping immediate leave ip igmp snooping drop unknown Description The ip igmp snooping drop unknown command is used to process the unknown multicast as discard To disable the operation of processing the unknown multicast as discard please use no ip igmp snooping drop unknown command Syntax ip igmp snooping drop unknown no ip igmp snooping drop unknown Command Mode Global Configuration Mode Example Specify the operation to process unknown multicast as discard TL SG3424 config ip igmp snooping drop unknown 204 ip i gmp snooping vlan config Description The ip igmp snooping vlan config command is used to enable VLAN IGMP Snooping function or to modify IGMP Snooping parameters and to create static multicast IP en
28. Remote Monitoring basing on SNMP architecture functions to monitor the network History Group is one of the commonly used RMON Groups After a history group is configured the switch collects network statistics information 241 periodically based on which the management station can monitor network effectively Syntax rmon history index interface gigabitEthernet port interval seconds owner owner name no rmon history index Parameter index The index number of the entry ranging from 1 to 12 in the format of 1 3 5 port The Ethernet port number seconds The interval to take samplings from the port ranging from 10 to 3600 in seconds By default it is 1800 owner name The owner of the history sample entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the sample port as Gi1 0 2 and the sample interval as 100 seconds for the entry 1 3 TL SG3424 config rmon history 1 3 interface gigabitEthernet 1 0 2 interval 100 owner owner 1 rmon event Description The rmon event command is used to configure the entries of SNMP RMON Event To return to the default configuration please use no rmon event command Event Group as one of the commonly used RMON Groups is used to define RMON events Alarms occur when an event is detected Syntax rmon event index user user name description descript type none
29. TL SG3424 config no ipv6 mid snooping report suppression 215 ipv6 mld snooping unknown filter Description The ipv6 mld snooping unknown filter command is used to enable the unknown multicast packets filter function To disable this function please use no ipv6 mld snooping unknown filter command By default it is disabled Syntax ipv6 mld snooping unknown filter no ipv6 mld snooping unknown filter Command Mode Global Configuration Mode Example Enable unknown multicast filter function TL SG3424 config ipv6 mld snooping unknown filter ipv6 mid snooping last listener query inteval Description The ipv6 mld snooping last listener query inteval command is used to specify the interval to send Specific Query Message The default value is 1 second To restore the default interval please use no ipv6 mid snooping last listener query inteval command Syntax ipv6 mld snooping last listener query inteval interval no ipv6 mld snooping last listener query inteval Parameter interval Specify the interval to send Specific Query Message in seconds ranging from 1 to 5 Command Mode Global Configuration Mode Example Specify the interval of Specific Query Message to 3 seconds TL SG3424 config ipv6 mld snooping last listener query inteval 3 216 ipv6 mid snooping last listener query count Description The ipv6 mld snooping last listener query count command is used to specify the numbers of Specific Query Mes
30. When the BOOTP Protocol is enabled the switch will try to obtain IP address from BOOTP Server This command should be configured in the Interface Configuration Mode of the management VLAN Syntax ip address alloc bootp Command Mode Interface Configuration Mode interface vian Example Enable the BOOTP Protocol to obtain IP address from BOOTP Server when the management VLAN of the switch is VLAN1 TL SG3424 config interface vian 1 TL SG3424 config if ip address alloc bootp reset Description The reset command is used to reset the switch s software After resetting all configuration of the switch will restore to the factory defaults and your current settings will be lost Syntax reset Command Mode Privileged EXEC Mode Example Reset the software of the switch 118 TL SG3424 reset reboot Description The reboot command is used to reboot the switch To avoid damage please don t turn off the device while rebooting Syntax reboot Command Mode Privileged EXEC Mode Example Reboot the switch TL SG3424 reboot copy running config startup config Description The copy running config startup config command is used to save the current settings Syntax copy running config startup config Command Mode Privileged EXEC Mode Example Save current settings TL SG3424 copy running config startup config copy startup config tftp Description The copy startup config tftp command is u
31. addresses are supported for example 192 168 0 1 or fe80 1234 Command Mode Global Configuration Mode Example Download an SSH 1 type key file named ssh key from TFTP server with the IP address 192 168 0 148 TL SG3424 config ip ssh download v1 ssh key ip address 192 168 0 148 Download an SSH 1 type key file named ssh key from TFTP server with the IP address fe80 1234 TL SG3424 config ip ssh download v1 ssh key ip address fe80 1234 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH 98 Syntax show ip ssh Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of SSH TL SG3424 config show ip ssh 99 Chapter 16 SSL Commands SSL Secure Sockets Layer a security protocol is to provide a secure connection for the application layer protocol e g HTTP based on TCP Adopting asymmetrical encryption technology SSL uses key pair to encrypt decrypt information A key pair refers to a public key contained in the certificate and its corresponding private key By default the switch has a certificate self signed certificate and a corresponding private key The Certificate Key Download function enables the user to replace the default key pair ip http secure server Description The ip http secure server command is used to enable the SSL function globally on the switch To disable the SSL function please use no i
32. be displayed in the encrypted form acct key O password 7 encrypted password O and 7 are the encryption type 0 indicates that an unencrypted password will follow 7 indicates that a symmetric encrypted password with a fixed length will follow By default the encryption type is 0 password is the shared password for the switch and the authentication servers to exchange messages which contains 31 characters at most The question marks and spaces are not allowed encrypted password is a symmetric encrypted password with a fixed length which you can copy from another switch s configuration file The password or encrypted password you configured here will be displayed in the encrypted form Command Mode Global Configuration Mode Example Configure the IP address of the accounting server as 10 20 1 100 and password as tplink TL SG3424 config radius auth pri 10 20 1 100 auth key tplink radius server account Description The radius server account command is used to enable the accounting feature To disable the accounting feature please use no radius server account command radius server account no radius server account Command Mode Global Configuration Mode Example Enable the accounting feature TL SG3424 config radius server account 86 show dot1x global Description The show dot1x global command is used to display the global configuration of 801 X Syntax show dot1
33. command The GVRP feature can only be enabled for the trunk type ports Syntax gvrp no gvrp Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet 42 Example Enable the GVRP function for ports 2 6 TL SG3424 config interface range gigabitEthernet 1 0 2 6 TL SG3424 config if range gvrp gvrp registration Description The gvrp registration command is used to configure the GVRP registration type on the desired port To restore to the default value please use no gvrp registration command Syntax gvrp registration normal fixed forbidden no gvrp registration Parameter normal fixed forbidden Registration mode By default the registration mode is normal Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the GVRP registration mode on ports 2 6 to fixed TL SG3424 config interface range gigabitEthernet 1 0 2 6 TL SG3424 config if range gvrp registration fixed gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired port To restore to the default setting of a GARP timer please use no gvrp timer command Syntax gvrp timer leaveall join leave value 43 no gvrp timer leaveall join leave Parameter leaveall join leave They are the three timers leaveall join and leave Once the LeaveAll Ti
34. command is used to display SNMP configuration globally Syntax show snmp server Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display SNMP configuration globally TL SG3424 show snmp server show snmp server view Description The show snmp server view command is used to display the View table Syntax show snmp server view Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the View table TL SG3424 show snmp server view show snmp server group Description The show snmp server group command is used to display the Group table 245 Syntax show snmp server group Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Group table TL SG3424 show snmp server group show snmp server user Description The show snmp server user command is used to display the User table Syntax show snmp server user Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the User table TL SG3424 show snmp server user show snmp server community Description The show snmp server community command is used to display the Community table Syntax show snmp server community Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Community table TL SG3424 show snmp server community 246 show snmp server host Description The show snmp server host command is used to display the H
35. config lldp Ildp hold multiplier Description The Ildp hold multiplier command is used to configure the Hold Multiplier parameter The aging time of the local information in the neighbor device is determined by the actual TTL value used in the sending LLDPDU TTL Hold Multiplier Transmit Interval To return to the default configuration please use no lidp hold multiplier command Syntax lldp hold multiplier multiplier no lidp hold multiplier 250 Parameter multiplier Configure the Hold Multiplier parameter It ranges from 2 to 10 By default it is 4 Command Mode Global Configuration Mode Example Specify Hold Multiplier as 5 TL SG3424P config lldp hold multiplier 5 Ildp timer Description The dp timer command is used to configure the parameters about transmission To return to the default configuration please use no dp timer command Syntax lldp timer tx interval tx interval tx delay tx delay reinit delay reinit delay notify interval notify interval fast count fast count no lidp timer tx interval tx delay reinit delay notify interval fast count Parameter tx interval Configure the interval for the local device to transmit LLDPDU to its neighbors The value ranges from 5 to 32768 seconds and the default value is 30 seconds tx delay Configure a value from 1 to 8192 in seconds to specify the time for the local device to transmit LLDPDU to its neighbo
36. delete the corresponding rule please use no access list extended command Syntax access list extended ac id rule rule id deny permit sip source ip smask source ip mask dip destination ip dmask destination ip mask tseg time segment dscp dscp s port s port d port d port tcpflag tcpflag protocol protocol tos tos pri pri no access list extended acl d rule rule id Parameter acl id The desired Extended IP ACL for configuration rule id The rule ID deny The operation to discard packets permit The operation to forward packets It is the default value source ip The source IP address contained in the rule source ip mask The source IP address mask It is required if you typed the source IP address destination ip The destination IP address contained in the rule destination ip mask The destination IP address mask It is required if you typed the destination IP address time segment The time range for the rule to take effect By default it is not limited dscp Specify the dscp value ranging from 0 to 63 s port The source port number d port The destination port number tcpflag Specify the flag value when using TCP protocol protocol Configure the value of the matching protocol 177 rule tos Enter the IP ToS contained in the rule pri Enter the IP Precedence contained in
37. eex teases eae eal 133 Us O tO EE 134 VII GUpICK A O AO 135 O EEN 136 Stonm control broad CASE seiseccee asec eden ci edacne idee cite eee cane ie eee eden cece eacnceeee 136 stormecontrol M lticaS titan ieee ieee eee 137 StorM CONtTOl UNCAS EE 138 bandwidth Peete eee Cee tie Rete A en eee 138 CIB geen nati A A A A TA AAA 139 show nterface Stallman dt de da ed A ENEE NEEESE ENE EESE EEEE 140 show Interface COUNTS ud at 140 show interface description aeaaaee eaae ferias eaaa Er EAEI E KAKE SEEE dc 141 Show interface flowcontrol anran aA Aaa E edie a EAO EAA ine utes 141 show interface configuration oooonoccccnnnoccccnononcccnononcccnonnnncnnnnnnnnncnnnnnnnnnnnnnnnnnnnannn cn nnannncnncnnnes 142 SHOWSTOTM CONTO italia AAA CREA aia CAE 142 Ge s eu BEE 143 Chapter 21 QoS Commande AA 144 JOS ai e 144 QOS dSCp aaa 144 dos UE E e EE 145 Os QUEUC Asco MPa aaa ie 146 GOS UU MOE tipa A A E A 147 SHOW GOS tE i it 148 SHOW GOS COS INAD GUN A AA AA AA AA AAA AAA 148 SHOW GOS ASCO IMA 00 da A A A A AAA AAA 149 SHOW GOS QUEUE MOTE ia Ria 149 SNOW GOS SlAlUS hisched eee cetocedecctece ce devee ce leer idad eege Dead EN ENEN EKEN e AA A eee 150 Chapter 22 Port Mirror Commande ssesennnnnnneeeeeennnrtttrrrrnrnrrrrttrtrrnnnnrrrrrrrreeen 151 monitor session destination interface cccccceccceeceeeeeeeeeeeeeeeeeeeeeeeeseceeeeeeseeeeeesseieeeeeeseas 151 monitor session source Interface 152 show monitor Session 153 Ch
38. host Description The snmp server host command is used to add Notification To delete the corresponding Notification please use no snmp server host command Syntax snmp server host ip udp port username smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv type trap inform retries retries timeout timeout no snmp server host ip user name 235 Parameter ip The IP Address of the management Host Both IPv4 and IPv6 addresses are supported for example 192 168 0 100 or fe80 1234 udp port UDP port which is used to send notifications The UDP port functions with the IP address for the notification sending It ranges from 1 to 65535 user name The User name of the management station smode v1 v2c v3 The Security Model of the management station with v1 v2c and v3 options By default the option is v1 slev noAuthNoPriv authNoPriv authPriv The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the option is noAuthNoPriv type trap inform The type of the notifications with trap and inform options Trap indicates traps are sent while inform indicates informs are sent The inform type has a higher security than the trap type and resend and timeout need to be con
39. id The priority of port It ranges from O to 7 which represent CoS0 CoS7 respectively By default the priority is 0 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet User Guidelines Port priority is one property of the port When the port priority is specified the data will be classified into the egress queue based on the CoS value of the ingress port and the mapping relation between the CoS and TC in gos queue cos map Example Configure the priority of port 5 as 3 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if qos 3 qos dscp Description The qos dscp command is used to enable the mapping relation between DSCP Priority and CoS value To disable the mapping relation please use no qos dscp command 144 Syntax qos dscp no qos dscp Command Mode Global Configuration Mode User Guidelines DSCP DiffServ Code Point is a new definition to IP ToS field given by IEEE DSCP priorities are mapped to the corresponding 802 1p priorities IP datagram will be classified into the egress queue based on the mapping relation between DSCP priority and CoS value Example Enable the mapping relation between DSCP Priority and CoS value TL SG3424 config qos dscp qos queue cos map Description The qos queue cos map command is used to configure the mapping relation between IEEE 802 1P priority tag IEEE 802 1Q tag CoS value and the TC egres
40. inline supply enable power inline profile Description The power inline profile command is used to bind a PoE profile to the corresponding port To cancel the bind relation please use no power inline profile command Syntax power inline profile name no power inline profile Parameter name The name of the PoE profile to be bound to the port If the name being assigned contains spaces then put it inside double quotes Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Bind the PoE profile named IP Camera to port 2 168 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if power inline profile IP Camera power inline time range Description The power inline time range command is used to bind a PoE time range to the corresponding port To cancel the bind relation please use no power inline time range command Syntax power inline time range name no power inline time range Parameter name The name of the PoE time range to be bound to the port Command Mode Interface Configuration Mode Example Bind the PoE time range named tRange2 to port 2 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if power inline time range tRange2 show power inline Description The show power inline command is used to display the global PoE information of the system Syntax show power inlin
41. port list The list of Ethernet ports Command Mode Global Configuration Mode 205 Example Enable the IGMP Snooping function and modify Router Port Time as 300 seconds Member Port Time as 200 seconds for VLAN1 3 and set the Leave time as 15 seconds for VLAN1 2 TL SG3424 config ip igmp snooping vlan config 1 3 rtime 300 TL SG3424 config ip igmp snooping vlan config 1 3 mtime 200 TL SG3424 config ip igmp snooping vlan config 1 2 Itime 15 Add static multicast IP address 225 0 0 1 which correspond to VLAN 2 and configure the forward port as port 1 3 TL SG3424 config ip igmp snooping vian config 2 static 225 0 0 1 interface gigabitEthernet 1 0 1 3 ip igmp snooping multi vlan config Description The ip igmp snooping multi vlan config command is used to create Multicast VLAN To delete the corresponding Multicast VLAN please use no ip igmp snooping multi vlan config command Syntax ip igmp snooping multi vlan config vlan id rtime router time mtime member time Itime leave time rport interface gigabitEthernet port no ip igmp snooping multi vlan config Parameter vid The ID of the VLAN desired to modify configuration ranging from 2 to 4094 router time Router Port Time Within this time if the switch does not receive IGMP query message from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By default it is 300 membe
42. port list port isolation Description The port isolation command is used to configure the forward port list of a port so that this port can only communicate with the ports on its port list To delete the corresponding configuration please use no port isolation command Syntax port isolation gi forward list gi forward list no port isolation Parameter gi forward list The list of Ethernet ports Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Set port 1 2 and 4 to the forward port list of port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if f port isolation gi forward list 1 0 1 2 1 0 4 Set all Ethernet ports to forward port list of port 2 namely restore to the default setting TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if no port isolation show port isolation interface Description The show port isolation interface command is used to display the forward port list of a port 154 Syntax show port isolation interface gigabitEthernet port Parameter port The number of Ethernet port you want to show its forward port list in the format of 1 0 2 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the forward list of port 2 TL SG3424 show port isolation interface gigabitEthernet 1 0 2 Display the forward list of all Ethernet ports TL SG
43. power limit as 5w for port 2 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if power inline consumption 50 power inline priority Description The power inline priority command is used to configure the PoE priority for the corresponding port Syntax power inline priority low middle high Parameter priority The PoE priority of the port The priority levels include high middle and low in descending order When the supply power exceeds the system power limit the PD linked to the port with lower priority will be disconnected By default the priority level is low Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the PoE priority as low for port 2 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if power inline priority low 167 power inline supply Description The power inline supply command is used to configure the PoE status of the corresponding port Syntax power inline supply enable disable Parameter enable disable The PoE status of the port By default the PoE status is enable Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the PoE feature for port 2 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if power
44. sent when MAC address learning mode of the switch changes max learned Enable MAC address max learned trap It is sent when the amount of learned MAC address reaches the limit which is configured in port security module Command Mode Global Configuration Mode Example Enable all SNMP extended MAC address related traps for the switch 240 TL SG3424 config snmp server traps mac Enable new MAC address trap only for the switch TL SG3424 config snmp server traps mac new snmp server traps vian Description The snmp server traps vlan command is used to enable SNMP extended VLAN related traps which include two types create and delete To disable this function please use no snmp server traps vlan command Syntax snmp server traps vlan create delete no snmp server traps vlan create delete Parameter create Enable VLAN created trap It is sent when new VLAN is created successfully delete Enable VLAN deleted traps It is sent when VLAN is deleted successfully Command Mode Global Configuration Mode Example Enable all SNMP extended VLAN related traps for the switch TL SG3424 config snmp server traps vian Enable VLAN created trap only for the switch TL SG3424 config snmp server traps vlan create rmon history Description The rmon history command is used to configure the history sample entry To return to the default configuration please use no rmon history command RMON
45. server TL SG3424 config show radius authentication 88 Chapter 14 System Log Commands The log information will record the settings and operation of the switch respectively for you to monitor operation status and diagnose malfunction logging buffer Description The logging buffer command is used to configure the severity level and the status of the configuration input to the log buffer To disable the logging buffer function please use no logging buffer command Local Log is the log information saved in the switch It has two output channels that is it can be saved to two different positions log buffer and log file The log buffer indicates the RAM for saving system log and the information in the log buffer can be got by show logging buffer command It will be lost when the switch is restarted Syntax logging buffer level no logging buffer Parameter level Severity level of the log information output to each channel There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be output By default it is 6 indicating that all the log information between level 0 6 will be saved in the log buffer Command Mode Global Configuration Mode Example Set the severity level as 5 TL SG3424 config logging buffer 5 89 logging file flash Description The logging file flash command is used to store the log messag
46. show qos interface Description The show qos interface command is used to display the configuration of QoS based on port priority Syntax show qos interface gigabitEthernet port range gigabitEthernet port list Parameter port The Ethernet port number port list The list of Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of QoS for port 5 TL SG3424 show qos interface gigabitEthernet 1 0 5 Display the configuration of QoS for ports 1 4 TL SG3424 show qos interface range gigabitEthernet 1 0 1 4 show qos cos map Description The show qos cos map command is used to display the configuration of IEEE 802 1P Priority and the mapping relation between cos id and tc id Syntax show qos cos map 148 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of IEEE 802 1P Priority and the mapping relation between cos id and tc id TL SG3424 show qos cos map show qos dscp map Description The show qos dscp map command is used to display the configuration of DSCP Priority Syntax show qos dscp map Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of DSCP Priority TL SG3424 show gos dscp map show qos queue mode Description The show qos queue mode command is used to display the schedule rule of the egress queues Syntax show qos
47. status of DHCP Snooping Syntax show ip dhcp snooping information Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Option 82 configuration status of DHCP Snooping TL SG3424 show ip dhcp snooping information show ip dhcp snooping interface gigabitEthernet Description The show ip dhcp snooping interface gigabitEthernet command is used to display the DHCP Snooping configuration of desired Gigabit Ethernet ports Syntax show ip dhcp snooping interface gigabitEthernet port Parameters port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode 70 Example Display the DHCP Snooping configuration of port 2 TL SG3424 show ip dhcp snooping interface gigabitEthernet 1 0 2 71 Chapter 11 ARP Inspection Commands ARP Address Resolution Protocol Detect function is to protect the switch from the ARP cheating such as the Network Gateway Spoofing and Man In The Middle Attack etc ip arp inspection global Description The ip arp inspection command is used to enable the ARP Detection function globally To disable the ARP Detection function please use no ip arp detection command Syntax ip arp inspection no ip arp inspection Command Mode Global Configuration Mode Example Enable the ARP Detection function globally TL SG3424 config ip arp inspection ip arp inspection trust Description The ip arp inspection trust command is used
48. switch the priority levels are labeled as TCO TC1 TC3 Syntax qos queue mode sp wrr sp wrr equ no qos queue mode Parameter sp Strict Priority Mode In this mode the queue with higher priority will occupy the whole bandwidth Packets in the queue with lower priority are sent only when the queue with higher priority is empty wrr Weight Round Robin Mode In this mode packets in all the queues are sent in order based on the weight value for each queue The weight value ratio of TCO TC1 TC2 and TC3 is 1 2 4 8 sp wrr Strict Priority Weight Round Robin Mode In this mode the switch provides two scheduling groups SP group and WRR group Queues in SP group and WRR group are scheduled strictly based on Strict Priority mode while the queues inside WRR group follow the WRR mode In SP WRR mode TC3 is the SP group TCO TC1 and TC2 belong to the WRR group and the weight value ratio of TCO TC1 and TC2 is 1 2 4 In this way when scheduling queues the switch allows TC3 to occupy the whole bandwidth following the SP mode and the TCO TC1 and TC2 in the WRR group will take up the bandwidth according to their ratio 1 2 4 147 equ Equal Mode In this mode all the queues occupy the bandwidth equally The weight value ratio of all the queues is 1 1 1 1 Command Mode Global Configuration Mode Example Specify the Schedule Mode as Weight Round Robin Mode TL SG3424 config qos queue mode wrr
49. table max mac count interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the security configuration of all ports TL SG3424 config show mac address table max mac count interface gigabitEthernet Display the security configuration of port 1 TL SG3424 config show mac address table max mac count interface gigabitEthernet 1 0 1 show mac address table interface gigabitEthernet Description The show mac address table interface gigabitEthernet command is used to display the address configuration of the specified port Syntax show mac address table interface gigabitEthernet port 107 Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the address configuration of port 1 TL SG3424 config show mac address table interface gigabitEthernet 1 0 1 show mac address table count Description The show mac address table count command is used to display the total amount of MAC address table Syntax show mac address table count Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the total amount of MAC address table TL SG3424 config show mac address table count show mac address table address Description The show mac address table address command is used to display the information of the specified MAC add
50. the rule Command Mode Global Configuration Mode Example Create an Extended IP ACL whose ID is 220 and add Rule 10 for it In the rule the source IP address is 192 168 0 100 the source IP address mask is 255 255 255 0 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TL SG3424 config access list create 220 TL SG3424 config access list extended 220 rule 10 permit sip 192 168 0 100 smask 255 255 255 0 tseg tSeg1 Description The rule command is used to configure MAC ACL rule To delete the corresponding rule please use no rule command rule rule id deny permit smac source mac smask source mac mask IT dmac destination mac dmask destination mac mask vid vlan id type ethernet type pri user pri tseg time segment no rule rule id Parameter rule id The rule ID deny The operation to discard packets permit The operation to forward packets It is the default value source mac The source MAC address contained in the rule source mac mask The source MAC address mask lt is required if you typed the source MAC address destination mac The destination MAC address contained in the rule destination mac mask The destination MAC address mask It is required if you typed the destination MAC address vlan id The VLAN ID contained in the rule ranging from 1 to 4094 17
51. to add the static MAC address entry To remove the corresponding entry please use no mac address table static command The static address can be added or removed manually independent of the aging time In the stable networks the static MAC address entries can facilitate the switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably Syntax mac address table static mac addr vid vid interface gigabitEthernet port no mac address table static mac addr vid vid mac addr vid vid interface gigabitEthernet port Parameter mac addr The MAC address of the entry you desire to add vid The VLAN ID number of your desired entry It ranges from 1 to 4094 port The Ethernet port number of your desired entry Command Mode Global Configuration Mode Example Add a static Mac address entry to bind the MAC address 00 02 58 4f 6c 23 VLAN1 and port 1 together TL SG3424 config mac address table static 00 02 58 4f 6c 23 vid 1 interface gigabitEthernet 1 0 1 103 mac address table aging time Description The mac address table aging time command is used to configure aging time for the dynamic address To return to the default configuration please use no mac address table aging time command Syntax mac address table aging time aging time no mac address table aging time Parameter aging time The aging time for the dynamic address The value of it can be O or ranges from 10 to 6
52. to configure the VLAN Instance mapping To remove the VLAN instance mapping or disable the corresponding instance please use no instance command When an instance is disabled the related mapping VLANs will be removed Syntax instance instance id vlan vlan id no instance instance id vlan vlan id Parameters instance id Instance ID ranging from 1 to 8 vlan id The VLAN ID selected to mapping with the corresponding instance Command Mode MST Configuration Mode Example Map the VLANs 1 100 to Instance 1 TL SG3424 config spanning tree mst configuration TL SG3424 config mst instance 1 vlan 1 100 Disable Instance 1 namely remove all the mapping VLANs 1 100 TL SG3424 config spanning tree mst configuration TL SG3424 config mst no instance 1 Remove VLANs 1 50 in mapping VLANs 1 100 for Instance 1 190 TL SG3424 config spanning tree mst configuration TL SG3424 config mst no instance 1 vlan 1 50 name Description The name command is used to configure the region name of MST instance Syntax name name Parameters name The region name used to identify MST region It ranges from 1 to 32 characters Command Mode MST Configuration Mode Example Configure the region name of MST as region1 TL SG3424 config spanning tree mst configuration TL SG3424 config mst name region1 revision Description The revision command is used to configure the revision level of MST instance Syntax revi
53. 0 admin 21 enable secret Description The enable secret command is used to set a secret password which is using an MIDD encryption algorithm for users to access Privileged EXEC Mode from User EXEC Mode To return to the default configuration please use no enable secret command This command uses the MD5 encryption Syntax enable secret 0 password 5 encrypted password no enable secret Parameter 0 Specify the encryption type O indicates that an unencrypted password will follow By default the encryption type is 0 password Super password a string from 1 to 31 alphanumeric characters or symbols The password is case sensitive allows digits English letters case sensitive underlines and sixteen special characters By default it is empty The password in the configuration file will be displayed in the MD5 encrypted form 5 Indicates an MD5 encrypted password with fixed length will follow encrypted password An MIDD encrypted password with fixed length which you can copy from another switch s configuration file After the encrypted password is configured you should use the corresponding unencrypted password if you re enter this mode Command Mode Global Configuration Mode User Guidelines If both the enable password and enable secret are defined you must enter the password set in enable secret Example Set the secret password as admin and unencr
54. 114 VI NOM E 115 A OS 115 Eller Le A 116 ip management ET 116 paddies Siri AA AAA A ee 117 ip address allOG ICO tiva aa asadas dadadada addoed anai daai inas 117 ip address alloc booftp cnn nnn EEEE EEEEEEEEA EEE EEEE E EEEE EEEn 118 NOSCU reene 118 EDO OL EE 119 copy running config Startup CON IO cooooccccnnnoccccnnnncccncnnnoncnnnnnnonononnnncnnnnnnncnnnoncnnnnnnnnannnccnnnnnes 119 copy Sstartup contig titp sitet ae ee ro eee ene 119 copy UR RE leen e ee e eee es 120 firMWare poLadO iii in sees tea eee ae eee es 121 O O 121 En GE 122 Ne EE EE 123 NASA E ates 124 Ell Er EE 124 SNOW SYSTSIMAINTO A A AAA 124 Show running Config es sion inaaya eae ie ean ie ov ee ca et ete eis ENE ee evn cp da aud ce RARA RARA nAncaRiASA 125 show cable diagnostics interface c ccccccceceeeeceeeeeeeeeeeeeeeeeeeesecneeeeeeceeeeeeeeseneeeeeneneeeetees 125 Chapter 19 IPv6 Address Configuration Commande 127 IPVO ue 127 ipv6 address QULOCONAIG ccoooccccncnoocccccnoncccnnnnnononnnnnnncnnnnnnncnncnnnnnnn non nn cnn nannn cnn cnn nn nnnnniannncnnnnnnss 127 ipv6 address Wmnk Jocal cnn conan cnn nnonnnnnncnnnn nn cnn nnnnnncnnnnnnss 128 NM e ee EE 128 IR ele EE 129 IEN address Ulla 130 lee 130 Show ipv6 interface vam 131 Chapter 20 Ethernet Configuration Commande sssssseeeseeeeneneeseneeeereeereeeeseeene 132 interface e e le EN E 132 interface range dlogabittibermet AA 132 e lee BEE 133 A gedet Pen eae Daee ete eee tree
55. 192 Spanning tree MOS A Da EEGEN 192 spanning tree proa tl 193 spanning tree tc defend oooooooconnncccconoooooonnnnncconnnonononnnonccnnnnnnnnnnnnnnccnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnos 194 Spanning tree mer 194 Spanning tree hold count ii nd 195 SPanning tree MAX NONS ocoooocccnnncccconooonnnnnnnnccnononnnnonnnnnncnnnnnnnnnnnnnnncnnnnnnnnnnnnnnnnnnnnnninnnnnnnnennnos 196 spanning tree bpdufilter ccomoooooocconccccononononnnnnnccnonononnnnonnnconononnnonnnnnnnnnnccnonannnnnnnnnnos 196 spanning tree bpduguard DEE 197 spanning tree guard ee EEN 197 spanning tree guard ele LEE 198 Spanning treeg ard E 198 spanning nee 199 show Spanning tree active ooooococcnnnoccccnnnoocccconnoccnnonnnncnnnnnnncnnnnnnnnnnnnnnnnnnnnannncnnnnnnnnnnnncnnnnncnnens 199 show Spanning tree Bridge vor iaa eee 200 show spanning tree Interface 200 show spanning tree interface security ccccceeeeececeeeeeneeeeeeeeeeeeecneeeeseseaeeeseeneeeesseineeetees 201 NA EE 201 Chapter 28 IGMP Snooping Commande 203 ip igmp Snooping global EE 203 ip igmp Snooping interface circa iii aid tt eee gence ede 203 ip igmp snooping immediate leave nnenneeeeneeeeeetetetetttetttttetttttttttrttetttntettnntertentsereeene rene 204 ip IGMP snooping drop UNKNOWN ss ssssskessekttseetrttettttttttttttttttsttEtnttEEnEtEEnEnEEn nsere r Enneee Eneee 204 ip igmp snooping vlan config ccoooococcnnonccccononoccnnnonancnnnonancnnnnnnnnnnnonnnnnn
56. 2 router aging time 100 ipv6 mid snooping vlan member aging time Description The ipv6 mld snooping vlan member aging time command is used to specify member port aging time for a specified VLAN If this time is set to 0 then the global member port aging time will be used The default time is 0 To restore the default timer please use no ipv6 mld snooping vlan member aging time command Syntax ipv6 mld snooping vlan vian id member aging time timer no ipv6 mld snooping vlan vian id member aging time Parameter vlan id The specified IEEE 802 1Q VLAN ID ranging from 1 to 4094 timer Aging time of the member port in seconds ranging from 200 to 1000 and 0 Command Mode Global Configuration Mode 219 Example Specify the member port aging time as 100 seconds in VLAN 2 TL SG3424 config ipv6 mld snooping vlan 2 member aging time 100 ipv6 mid snooping vlan immediate leave Description The ipv6 mld snooping vlan immediate leave command is used to enable the immediate leave function on a specified VLAN To disable this funciton please use no ipv6 mld snooping vlan immediate leave command By default it is disabled Syntax ipv6 mld snooping vlan vian id immediate leave no ipv6 mld snooping vlan vian id immediate leave Parameter vlan id The specified IEEE 802 1Q VLAN ID to enable the immediate leave function ranging from 1 to 4094 Command Mode Global Configuration Mode Example Enable immed
57. 30 seconds When 0 is entered the Auto Aging function is disabled It is 300 by default Command Mode Global Configuration Mode Example Configure the aging time as 500 seconds TL SG3424 config mac address table aging time 500 mac address table filtering Description The mac address table filtering command is used to add the filtering address entry To delete the corresponding entry please use no mac address table filtering command The filtering address function is to forbid the undesired package to be forwarded The filtering address can be added or removed manually independent of the aging time Syntax mac address table filtering mac addr vid vid no mac address table filtering mac addr vid vid Parameter mac addr The MAC address to be filtered vid The corresponding VLAN ID of the MAC address It ranges from 1 to 4094 104 Command Mode Global Configuration Mode Example Add a filtering address entry of which VLAN ID is 1 and MAC address is 00 1e 4b 04 01 5d TL SG3424 config mac address table filtering 00 1e 4b 04 01 5d vid 1 mac address table max mac count Description The mac address table max mac count command is used to configure the Port Security To return to the default configurations please use no mac address table max mac count command Port Security is to protect the switch from the malicious MAC address attack by limiting the maximum number of the MAC addresses that can be
58. 3424 show port isolation interface 155 Chapter 24 Loopback Detection Commands With loopback detection feature enabled the switch can detect loops using loopback detection packets When a loop is detected the switch will display an alert or further block the corresponding port according to the configuration loopback detection global Description The loopback detection command is used to enable the loopback detection function globally To disable it please use no loopback detection command Syntax loopback detection no loopback detection Command Mode Global Configuration Mode Example Enable the loopback detection function globally TL SG3424 config loopback detection loopback detection interval Description The loopback detection interval command is used to define the interval of sending loopback detection packets from switch ports to network aiming at detecting network loops periodically Syntax loopback detection interval interval time Parameter interval time The interval of sending loopback detection packets It ranges from 1 to 1000 seconds By default this value is 30 Command Mode Global Configuration Mode 156 Example Specify the interval time as 50 seconds TL SG3424 config loopback detection interval 50 loopback detection recovery time Description The loopback detection recovery time command is used to configure the time after which the blocked port would automatical
59. 4 ExtPath Cost as 100 IntPath Cost as 100 and then enable Edge Port TL SG3424 config interface gigabitEthernet 1 0 1 TL SG3424 config if spanning tree common config port priority 64 ext cost 100 int cost 100 portfast enable point to point open spanning tree mode Description The spanning tree mode command is used to configure the STP mode of the switch To return to the default configurations please use no spanning tree mode command Syntax spanning tree mode stp rstp mstp no spanning tree mode Parameter stp Spanning Tree Protocol the default value rstp Rapid Spanning Tree Protocol mstp Multiple Spanning Tree Protocol Command Mode Global Configuration Mode Example Configure the spanning tree mode as mstp TL SG3424 config spanning tree mode mstp spanning tree mst configuration Description The spanning tree mst configuration command is used to access MST Configuration Mode from Global Configuration Mode as to configure the VLAN Instance mapping region name and revision level To return to the default 189 configuration of the corresponding Instance please use no spanning tree mst configuration command Syntax spanning tree mst configuration no spanning tree mst configuration Command Mode Global Configuration Mode Example Enter into the MST configuration mode TL SG3424 config spanning tree mst configuration instance Description The instance command is used
60. 6 mld snooping filter id 1 10 ipv6 mid snooping max group Description The ipv6 mld snooping max group command is used to specify the limit number of groups for a port to join in The default value is 256 To restore the default value please use no ipv6 mld snooping max group command Syntax ipv6 mld snooping max group imit no ipv6 mld snooping max group Parameter limit Specify the max number of multicast groups on a port ranging from 0 to 256 Command Mode Interface Configuration Mode Example Specify the limit group as 128 on interface gigabitEthernet 1 0 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ipv6 mld snooping max group 128 clear ipv6 mid snooping statistics Description The clear ipv6 mld snooping statistics command is used to clear the statistics of the MLD packets Syntax clear ipv6 mld snooping statistics Command Mode Privileged EXEC Mode and Any Configuration Mode 226 Example Clear the statistics of the MLD packets TL SG3424 config clear ipv6 mld snooping statistics show ipv6 mid snooping Description The show ipv6 mld snooping command is used to display the global configuration of MLD Snooping Syntax show ipv6 mld snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of MLD Snooping TL SG3424 config show ipv6 mld snooping show ipv6 mid snooping vian Description
61. 8 ethernet type EtherType contained in the rule in the format of 4 hex number user pri The user priority contained in the rule ranging from O to 7 By default it is not limited time segment The time range for the rule to take effect By default it is not limited Command Mode Mac Access list Configuration Mode Example Create a MAC ACL whose ID is 20 and add Rule 10 for it In the rule the source MAC address is 00 01 3F 48 16 23 the source MAC address mask is 11 11 11 11 11 00 VLAN ID is 2 the user priority is 5 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TL SG3424 config mac access list 20 TL SG3424 config mac acl rule 10 permit smac 00 01 3F 48 16 23 smask 11 11 11 11 11 00 vid 2 pri 5 tseg tSeg1 access list policy name Description Syntax The access list policy name command is used to add Policy To delete the corresponding Policy please use no access list policy name command A Policy is used to control the data packets those match the corresponding ACL rules by configuring ACLs and actions together for effect The operations here include stream mirror stream condition QoS Remarking and redirect access list policy name name no access list policy name name Parameter name The Policy Name ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add a Policy
62. 9 2 139 79 100 163 11 system time dst predefined Description The system time dst predefined command is used to select a predefined DST configuration and the configuration can be recycled Syntax system time dst predefined USA Australia Europe New Zealand Parameter USA Australia Europe New Zealand Predefined DST mode with four options USA Australia Europe and New Zealand By default the setting is Europe The DST time periods which the four predefined DST mode represents are displayed as follow USA Second Sunday in March 02 00 First Sunday in November 02 00 Australia First Sunday in October 02 00 First Sunday in April 03 00 Europe Last Sunday in March 01 00 Last Sunday in October 01 00 New Zealand Last Sunday in September 02 00 First Sunday in April 03 00 Command Mode Global Configuration Mode Example Configure the DST period of the switch as Europe TL SG3424 config system time dst predefined Europe 112 system time dst date Description The system time dst date command is used to specify the DST configuration in Date mode This configuration is one off in use By default the current year is used as the starting time DST time periods should be within 12 months over one two year Syntax system time dst date smonth sday stime 4 emonth y eday etime y offset Parameter smonth Month to start with the options Jan Feb Mar Apr May
63. CLI Reference Guide TL SG3210 TL SG3216 TL SG3424 TL SG3424P JetStream L2 Managed Switch REV3 0 0 1910011092 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright O 2014 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com CONTENTS RSAC ARA AAA TA AA Ez 1 Chapter 1 Using the Cll 4 1 1 Accessing the Clliuiadocarodoradodadadadadadeda dede 4 1 11 Logonby a Console Ott eeeee esoe EE A EN Ee 4 1 1 2 Configuring the Privileged EXEC Mode Password 6 13123 Logon by EN ET 7 1 14 LOJON DY SO AAA AAA 11 1 27 GELCoMmand Modes croata ARA ACES RA ante cnet 16 13 Security EE 18 T Conventions EE 18 L t Format Convention Seese a a hash heed a aE aTe 18 1 4 2 Special Character 19 1 43 Parameter Fomat ariii e e a a 19 Chapter 2 User interface siii ei 20 enable iison coin ves eee vee eee Seege Eege AA A A A ee ee ee ees 20 Service PASSWOLC ENCTYPTION eececcecceeeeceeeeeeeeeeeeeeeeeeeceaeeeeseaeeeesecaeeeeescneeeessecaeeeeeesseieeeeeneas 20 enable PassWord rta 21
64. Configuration Mode Example Specify the max response time as 10s on VLAN 2 TL SG3424 config ipv6 mld snooping querier vlan 2 max response time 10 222 ipv6 mid snooping querier vlan query interval Description The ipv6 mld snooping querier vlan query interval command is used to specify the interval to send the Query Message The default value is 25 seconds To restore the default value please use no ipv6 mld snooping querier vian query interval command Syntax ipv6 mld snooping querier vlan vian id query interval interval no ipv6 mld snooping querier vlan vian id query interval Parameter vlan id The VLAN that enables the MLD Querier function ranging from 1 to 4094 interval Specify the interval to send the Query message in seconds ranging from 2 to 300 Command Mode Global Configuration Mode Example Specify the interval to send the Query Message as 10s on VLAN 2 TL SG3424 config ipv6 mld snooping querier vlan 2 query interval 10 ipv6 mid snooping querier vlan query source Description The ipv6 mld snooping querier vlan query source command is used to specify the source address which sends the Query message The default value is FE80 02FF FFFF FE00 0001 To restore the default value please use no ipv6 mld snooping querier vlan query source command Syntax ipv6 mld snooping querier vlan vian id query source pv6 addr no ipv6 mld snooping querier vlan vian id query source Parameter vlan id
65. Configuration Mode interface vlan Example Configure the global address 3001 1 64 on the interface TL SG3424 config interface vlan 1 TL SG3424 config if ipv6 address 3001 1 64 show ipv6 interface vlan Description This command is used to display the configured ipv6 information of the management vlan interface including ipv6 function status link local address and global address ipv6 multicast groups etc Syntax show ipv6 interface vlan vian id Parameter vlan id The VLAN ID of the management VLAN Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ipv6 information of the management vlan interface TL SG3424 config show ipv6 interface vlan 1 131 Chapter 20 Ethernet Configuration Commands Ethernet Configuration Commands can be used to configure the Bandwidth Control Negotiation Mode and Storm Control for Ethernet ports interface gigabitEthernet Description The interface gigabitEthernet command is used to enter the Interface gigabitEthernet Configuration Mode and configure the corresponding Gigabit Ethernet port Syntax interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Global Configuration Mode Example To enter the Interface gigabitEthernet Configuration Mode and configure port 2 TL SG3424 config interface gigabitEthernet 1 0 2 interface range gigabitEthernet Description The interface range gigabitEther
66. G3424tconfig TL 63424 config line vty 0 5 TL 63424 config line login local Set login mode TL SG3424 config line Hexit TL SG3424 config H Enter the Privileged EXEC Mode password Connected 0 00 45 Auto detect 38400 8 N 1 Figure 1 7 Configure login local mode Now you can logon by Telnet in login local mode 1 Make sure the switch and the PC are in the same LAN Click Start Run to open the Run window and type cmd in the prompt Run window as Figure 1 8 and click OK ag Type the name of a program Folder document or Internet resource and Windows will open it for you Open OK Cancel Browse Figure 1 8 Run Window 2 Open Telnet and type telnet 192 168 0 1 in the command prompt shown as Figure 1 9 and press the Enter button c C WINDOWS system32 cmd exe Lo C Documents and Settings Admin gt telnet 192 168 8 1 Figure 1 9 Connecting to the Switch 3 Type the default user name and password admin admin then press the Enter button so as to enter User EXEC Mode cr Telnet 192 168 0 1 boooooseceneseoor User Access Login 0900000000000000 User zadmin Password iT L SG3424 gt Figure 1 11 Enter into the User EXEC Mode Now you can manage your switch with CLI commands through Telnet connection 4 Type enable command to enter Privileged EXEC Mode A password that you have set through Console port connection is required Here the password is set as 123
67. IP addresses ranges from 224 0 0 0 to 239 255 255 255 The range for receivers to join is from 224 0 1 0 to 239 255 255 255 Syntax ip igmp snooping filter addr id addr id list no ip igmp snooping filter addr id addr id list Parameter addr id list The filtering address ID to be bound Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet 207 Example Bind the filtering address ID 2 6 to port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if ip igmp snooping filter addr id 2 6 ip igmp snooping filter global Description The ip igmp snooping filter command is used to add or modify the multicast filtering IP range To delete the multicast filtering IP range please use no ip igmp snooping filter command Syntax ip igmp snooping filter id start ip end ip no ip igmp snooping filter id Parameter id IP range ID ranging from 1 to 30 start ip The start multicast IP of the IP range end ip The end multicast IP of the IP range Command Mode Global Configuration Mode Example Modify the multicast IP range whose ID is 3 as 225 1 1 1 226 3 2 1 TL SG3424 config ip igmp snooping filter 3 225 1 1 1 226 3 2 1 ip igmp snooping filter interface Description The ip igmp snooping filter command is used to configure Port Filter To return to the default configuration please use no igmp snooping filter command When the switch rec
68. MP RMON enabled entries is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Event configuration of entry1 4 TL SG3424 show rmon event 1 4 show rmon alarm Description The show rmon alarm command is used to display the configuration of the Alarm Management entry Syntax show rmon alarm index 248 Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 in the format of 1 3 5 You can select more than one entry for each command By default the configuration of all Alarm Management entries is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the Alarm Management entry 1 2 TL SG3424 show rmon alarm 1 2 249 Chapter 31 LLDP Commands Mote Only TL SG3424P supports LLDP function LLDP function enables network devices to advertise their own device information periodically to neighbors on the same LAN The information of the LLDP devices in the LAN can be stored by its neighbor in a standard MIB so it is possible for the information to be accessed by a Network Management System NMS such as SNMP Ildp Description The Ildp command is used to enable LLDP function To disable the LLDP function please use no Ildp command Syntax lldp no Ildp Command Mode Global Configuration Mode Example Enable LLDP function globally TL SG3424P
69. Mode Example Create monitor session 1 and configure port 1 as the monitoring port TL SG3424 config monitor session 1 destination interface gigabitEthernet 1 0 1 Delete the monitor session 1 TL SG3424 config no monitor session 1 151 monitor session source interface Description The monitor session source interface command is used to configure the monitored port To delete the corresponding monitored port please use no monitor session source interface command Syntax monitor session session_num source interface gigabitEthernet port list mode no monitor session session_num source interface gigabitEthernet port list mode Parameter session_num The monitor session number ranging from 1 to 4 port list List of monitored port It is multi optional mode The monitor mode There are three options rx tx and both Rx ingress monitoring mode means the incoming packets received by the monitored port will be copied to the monitoring port TX egress monitoring mode indicates the outgoing packets sent by the monitored port will be copied to the monitoring port Both ingress and egress monitoring presents the incoming packets received and the outgoing packets sent by the monitored port will both be copied to the monitoring port Command Mode Global Configuration Mode User Guidelines 1 The monitoring port is corresponding to current interface configuration mode 2 Monitored ports number is no
70. P Hops which is the hop count the switch topology collects NTDP Hops ranges from 1 to 16 By default it is 3 Command Mode Global Configuration Mode Example Enable NTDP function globally and specify NTDP Hops as 5 NTDP Interval Time as 30 minutes TL SG3424 config cluster ntdp TL SG3424 config cluster ntdp timer interval timer 30 TL SG3424 config cluster ntdp hop 5 cluster explore Description The cluster explore command is used to manually collect the topology information Syntax cluster explore Command Mode Global Configuration Mode Example Enable the topology information collecting function manually TL SG3424 config cluster explore cluster Description The cluster command is used to configure cluster function for specified ports To return to the default configuration please use no cluster command Syntax cluster ndp disable enable ntdp disable enable H no cluster 262 Parameter disable enable Enable Disable NDP function for the port By default it is enabled disable enable Enable Disable NTDP function for the port By default it is enabled Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable NDP and NTDP function for port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if cluster ndp enable ntdp enable cluster candidate Description The
71. SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if storm control unicast bandwidth Description The bandwidth command is used to configure the bandwidth limit for an Ethernet port To disable the bandwidth limit please use no bandwidth command Syntax bandwidth ingress ingress rate egress egress rate no bandwidth all ingress egress 138 Parameter ingress rate Specify the bandwidth for receiving packets Range 1 100000 for the megaport 1 1000000 for the gigaport egress rate Specify the bandwidth for sending packets Range 1 100000 for the megaport 1 1000000 for the gigaport all ingress egress Disable the bandwidth limitation function on the specified packet type all indicates the bandwidth limitation on receiving and sending packets is disabled ingress indicates the bandwidth limitation on receiving packets is diabled egress indicates the bandwidth limitation on sending packets is disabled Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the ingress rate as 5120Kbps and egress rate as 1024Kbps for port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if f bandwidth ingress 5120 egress 1024 clear counters Description The clear counters command is used to clear the statistic information of all the Ethernet ports Syntax clear co
72. Show QVip tele EE 44 SHOW QVIP interface EE 45 Chapter8 Etherchannel Commande snsssssseessenrnnrnntrnrrrrrrttrtrrrnnnnrr rrr rreeeenn 46 Channel Oro ke a aar geet Ee EENS Edge 46 port channel load balance A 47 Lach Seier PONY sorires assaia eieae EEEE ENEE the EENS NENNEN EENS edd 47 Tee Heen ele e EE 48 SAN e eege 48 show etherchannel Joad balance 49 SHOW lacp EE 49 SHOW ele DEE 50 Chapter9 User Manage COMMANdOS ccoccnonnnnnnnncnnnonnncnnnnnn nn 51 USE MN A ll dd 51 User NAME secret aeei et a a aaae eaa atana aaiae a Ka a eee aa ene ae ena eN E 52 user access control ip based isiin ari ein evi inc 53 user access control Mac based A 54 User access control portbased viii e E 54 VET POS 18 0 LS eene en e OS 55 AA o eee OS 56 Miri dd Ai 56 DASSWOIG DEE 57 ee EE 58 fe ell e 59 show user Lee tu E EE 59 show user configuration oooonoocccnnnnocccccnnncccnncnnnncnnonnnncnnnnnnncnnnnnnnnnnronnnrnnnnnnnnn nro nnannnnnnrnnerinninns 60 Chapter 10 Binding Table Commande 61 IP SOUMCEDINGING E 61 Ip SOUrCE DINGING INDEX tate eta hentia td cda 62 TA e eu Le EE 63 ip dhcp snooping global cceeececeeeeeeeeeeeeeeeeeeeeeeeeeeeseeaeeeeeeeaeeeeceeaeeeeeeceeeeseeeseeeeeseniseeeseees 63 ip dhcp snooping information option 64 ip dhcp snooping information strategy coooococcnnnocccnnnnoccccnononccnnonnnncnnonnnncnncnnnncnnnnnnn cnn cnnnnnnnnnns 65 ip dhcp snooping information remote jd enne 65 ip dhcp snoo
73. The show ip arp inspection command is used to display the ARP detection global configuration including the enable disable status and the Trusted Port list Syntax show ip arp inspection Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ARP detection configuration globally TL SG3424 config show ip arp inspection show ip arp inspection interface Description The show ip arp inspection interface command is used to display the interface configuration of ARP detection Syntax show ip arp inspection interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of all the ports 75 TL SG3424 config show ip arp inspection interface Display the configuration of port 2 TL SG3424 config show ip arp inspection interface gigabitEthernet 1 0 2 show ip arp inspection statistics Description The show ip arp inspection statistics command is used to display the number of the illegal ARP packets received Syntax show ip arp inspection statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the number of the illegal ARP packets received TL SG3424 config show ip arp inspection statistics clear ip arp inspection statistics Description The clear ip arp inspection statistics command is used to clear the statistic of the illegal ARP p
74. The show ipv6 mld snooping vlan command is used to display VLAN information of MLD Snooping Syntax show ipv6 mld snooping vlan v an id Parameter vlan id The VLAN ID selected to display ranging from 1 to 4094 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all of the VLAN information TL SG3424 config show ipv6 mld snooping vian 227 show ipv6 mid snooping static mcast Description The show ipv6 mld snooping static mcast command is used to display the static multicast groups configured by users Syntax show ipv6 mld snooping static mcast Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display static multicast groups TL SG3424 config show ipv6 mld snooping static mcast show ipv6 mid snooping group Description The show ipv6 mid snooping group command is used to display multicast groups Syntax show ipv6 mld snooping group dynamic static vlan vian id Parameter dynamic Display dynamic groups static Display static groups vlan id The VLAN ID selected to display ranging from 1 to 4094 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all of the multicast groups TL SG3424 config show ipv6 mld snooping group show ipv6 mid snooping filter Description The show ipv6 mld snooping filter command is used to display the filter entries 228 Syntax show ipv6 mld snooping filter
75. UTC 03 30 TimeZone for Tehran UTC 04 00 TimeZone for Moscow St Petersburg Volgograd Tbilisi Port Louis UTC 04 30 TimeZone for Kabul UTC 05 00 TimeZone for Islamabad Karachi Tashkent UTC 05 30 TimeZone for Chennai Kolkata Mumbai New Delhi UTC 05 45 TimeZone for Kathmandu UTC 06 00 TimeZone for Dhaka Astana Ekaterinburg UTC 06 30 TimeZone for Yangon Rangoon UTC 07 00 TimeZone for Novosibrisk Bangkok Hanoi Jakarta UTC 08 00 TimeZone for Beijing Chongqing Hong Kong Urumqi Singapore UTC 09 00 TimeZone for Seoul Irkutsk Osaka Sapporo Tokyo UTC 09 30 TimeZone for Darwin Adelaide UTC 10 00 TimeZone for Canberra Melbourne Sydney Brisbane UTC 11 00 TimeZone for Solomon Is New Caledonia Vladivostok UTC 12 00 TimeZone for Fiji Magadan Auckland Welington UTC 13 00 TimeZone for Nuku alofa Samoa ntp server The IP Address for the Primary NTP Server backup ntp server The IP Address for the Secondary NTP Server fetching rate Specify the rate fetching time from NTP server Command Mode Global Configuration Mode 111 Example Configure the system time mode as NTP the time zone is UTC 12 00 the primary NTP server is 133 100 9 2 and the secondary NTP server is 139 78 100 163 the fetching rate is 11 hours TL SG3424 config H system time ntp UTC 12 00 133 100
76. WEF INNER 169 show power inline configuration Interface 170 show power inline information Interface 170 Show power profile isip ccc See ee Dette ese See cies Pee ee ev ste ets Dele wet Dee eek NENEA NaNe cena dn ce dneudncneneytneneeee 170 Neel eg e le EE 171 SHOW POWER ime Tange anirai oseo sesen n nesese nenese ENEE EEEE EE ENEE EEKE EN ENEE EEEE KEE K AAEN ae eE N EET 171 Chapter 260 ACL CommMandS sccceseresteaseceseeeneeczecaseceneeuseecercusvensceuseeneccuswerseceseeeseenaet 172 lun 172 DSO REE ERE E REE EA EE RAEE OREA 172 A eege eege eege eege E EE EEEE EEE INN E NA E E OIR 173 NN 174 elle te ele IO 174 access list COALS eee ee LE 175 Macaco lluita 175 leen ET WEE 176 II 178 access list policy name erica cece dace cee 179 access list policy ACEI ON E 180 redirect interfaces a AA ee 180 FOCIFOCE VIE ET 181 elle AR O SS A IDE 181 SIMI EE 182 AOS rema ea anann A At 182 access list DING INLET ACE EE 183 eg ele LEE 184 Glen ue 184 Ne dl le e EEN 184 Dee lee EE 185 show lee gell 185 SHOW ACCeSSKHIISE iii A E N A a EA 186 Chapter 27 MSTP EEN 187 Spanning tree globall A 187 Spanning Dreeiintertace Entet EnnetEEnnrre nnne ee E 187 spanning tree COMIMON CON IY cccccncooooccnnnnccnnnnononnnnnnncnnonnnononnnnnnncnnnnnnnnnnnnnnncnnncnnnnnnnnnnnnnnss 188 SPANNING ES MOMS EE 189 spanning tree mst Configuration cnn i a 189 lt ln Le 190 NAME AREAS 191 VISION AA ARA ERRE EAL 191 Spanning tree MSt INStANCE ici ee eege
77. a Protocol based VLAN group please use no protocol vlan group command Syntax protocol vlan group group id no protocol vlan group group id Parameter group id The number of the Protocol based VLAN entry You can get the Protocol based VLAN entry corresponding to the number by the show protocol vlan vlan command 35 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Create Protocol based VLAN group 2 which is binding with port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if protocol vlan group 2 show protocol vlan template Description The show protocol vlan template command is used to display the information of the Protocol based VLAN templates Syntax show protocol vlan template Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the Protocol based VLAN templates TL SG3424 config show protocol vlan template show protocol vlan vlan Description The show protocol vlan vlan command is used to display the information about Protocol based VLAN entry Syntax show protocol vlan vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display information of the Protocol based VLAN entry TL SG3424 config show protocol vlan vlan 36 Chapter 6 Voice VLAN Commands Voice VLANs are configured specially for voice data stream By configuring Voic
78. ace range gigabitEthernet Example Configure the port 3 to operate in the auto voice VLAN mode 39 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if switchport voice vlan mode auto switchport voice vlan security Description The switchport voice vlan security command is used to enable the Voice VLAN security feature To disable the Voice VLAN security feature please use no switchport voice vlan security command Syntax switchport voice vlan security no switchport voice vlan security Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable port 3 for the Voice VLAN security feature TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if switchport voice vlan security show voice vlan Description The show voice vlan command is used to display the global configuration information of Voice VLAN Syntax show voice vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Voice VLAN globally TL SG3424 config show voice vlan 40 show voice vlan oui Description The show voice vlan oui command is used to display the configuration information of Voice VLAN OUI Syntax show voice vlan oui Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Voice VLAN OUI TL SG3424 confi
79. ackets received Syntax clear ip arp inspection statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Clear the statistic of the illegal ARP packets received TL SG3424 config clear ip arp inspection statistics 76 Chapter 12 DoS Defend Command DoS Denial of Service Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests to the Host With the DoS Defend enabled the switch can analyze the specific field of the received packets and provide the defend measures to ensure the normal working of the local network ip dos prevent Description The ip dos prevent command is used to enable the DoS defend function globally To disable the DoS defend function please use no ip dos prevent command Syntax ip dos prevent no ip dos prevent Command Mode Global Configuration Mode Example Enable the DoS defend function globally TL SG3424 config ip dos prevent ip dos prevent type Description The ip dos prevent type command is used to select the DoS Defend Type To disable the corresponding Defend Type please use no ip dos prevent type command Syntax ip dos prevent type land scan synfin xma scan null scan port less 1024 blat ping flood syn flood no ip dos prevent type land scan synfin xma scan null scan port less 1024 blat ping flood syn flood 77 Parameter land La
80. al Configuration Mode Mode VLAN Configuration Mode The following table gives detailed information about the Accessing path Prompt of each mode and how to exit the current mode and access the next mode Mode Accessing Path Prompt Logout or Access the next mode Use the exit command to disconnect the i i switch except that the switch is User EXEC Primary mode once it i p i i Mod is connected with the TL SG3424 gt connected through the Console port 99S switch Use the enable command to access Privileged EXEC mode Use the enable Enter the disable or the exit command ivi i to return to User EXEC mode Privileged command to enter this TL SG3424 EXEC Mode mode from User EXEC Enter configure command to access mode Global Configuration mode 16 Mode Accessing Path Prompt Logout or Access the next mode Use the exit or the end command or press Ctrl Z to return to Privileged EXEC mode Global SEN Beer Use the interface gigabitEthernet port Configuration a TL SG3424 config or interface range gigabitEthernet mode from Privileged Mode port list command to access interface EXEC mode 8 Configuration mode Use the vlan vlan list to access VLAN Configuration mode Use the interface gigabitEthernet port Use the end command or press Ctrl Z Interface or interface range TL SG3424 to return to Privileged EXEC mode Configuration gigabitEthernet config if or Enter the
81. ally To disable the IEEE 802 1X function please use no dot1x system auth control command Syntax dot1x system auth control no dot1x system auth control Command Mode Global Configuration Mode Example Enable the IEEE 802 1X function TL SG3424 config dot1x system auth control dot1x auth method Description The dot1x auth method command is used to configure the Authentication Method of IEEE 802 1X and the default 802 1x authentication method is eap md5 To restore to the default 802 1x authentication method please use no dot1x auth method command Syntax dot1x auth method pap eap md5 no dot1x auth method Parameter pap eap md5 Authentication Methods 79 pap IEEE 802 1X authentication system uses extensible authentication protocol EAP to exchange information between the switch and the client The transmission of EAP packets is terminated at the switch and the EAP packets are converted to the other protocol such as RADIUS packets for transmission eap md5 IEEE 802 1X authentication system uses extensible authentication protocol EAP to exchange information between the switch and the client The EAP protocol packets with authentication data can be encapsulated in the advanced protocol such as RADIUS packets to be transmitted to the authentication server Command Mode Global Configuration Mode Example Configure the Authentication Method of IEEE 802 1X as pap TL SG3424 config
82. and detecting the DoS attack Chapter 13 IEEE 802 1X Commands Provide information about the commands used for configuring IEEE 802 1X function Chapter 14 System Log Commands Provide information about the commands used for configuring system log Chapter 15 SSH Commands Provide information about the commands used for configuring and managing SSH Security Shell Chapter 16 SSL Commands Provide information about the commands used for configuring and managing SSL Secure Sockets Layer Chapter 17 MAC Address Commands Provide information about the commands used for Address configuration Chapter 18 System Configuration Commands Provide information about the commands used for configuring the System information and System IP reboot and reset the switch upgrade the switch system and commands used for cable test Chapter 19 IPv6 Address Configuration Commands Provide information about the commands used for configuring the System IPv6 addresses Chapter 20 Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control Negotiation Mode and Storm Control for Ethernet ports Chapter 21 QoS Commands Provide information about the commands used for configuring the QoS function Chapter 22 Port Mirror Commands Provide information about the commands used for configuring the Port Mirror function Chapter 23 Port Isolation Commands Provide information about the commands used for c
83. and is used to add a new user or modify the existed users information To delete the existed users please use no user name command This command uses the MD5 encryption Syntax user name name privilege admin guest secret 0 password 5 encrypted password no user name name Parameter name Type a name for users login which contains 16 characters at most composed of digits English letters and under dashes only admin guest Access level Admin means that you can edit modify and view all the settings of different functions Guest means that you can only view the settings without the right to edit and modify It is admin by default 0 Specify the encryption type 0 indicates that an unencrypted password will follow By default the encryption type is 0 password Users login password a string from 1 to 31 alphanumeric characters or symbols The password is case sensitive allows digits English letters case sensitive underlines and sixteen special characters 52 15 KI By default it is empty The password will be saved to the configuration file using the MD5 encrypted algorithm 5 Indicates an MD5 encrypted password with fixed length will follow encrypted password An MIDD encrypted password with fixed length which you can copy from another switch s configuration file Command Mode Global Configuration Mode User Guidelines 1 If
84. annes 80 GOLTX quiet period secos ii 81 GOLD Pete 81 dotix Max reatith Te Quilla etc ica poo 82 DO aaa 82 dot1x guest vlan interface A 83 dorr portecon tol 83 eeben Cd BEE 84 ll atada lada dada been eelere ee belie eect alee and 85 radius SEPVEl ACCOUNL osecec eve secer evel e ien celiac ege Sege A e E E reer AT Nae ce 86 show dott x global rt 87 SHOW Cot x Interface ceceeccceeceeeeeeeeeeeeeceeeeeeeeeaeeeeeeeaeeeeesceeeeeseeaeesecscaneneeeesseeeeeesseeeeeeseas 87 show radius ACCOUNTING cccceeeeeeceeceeeeeeeeeeeeeeeeecaeeeeceaeeeesecaeeeesecaeeeeesseeeeeeseeeaeeeesseieeeeseas 88 Show radius authentication cccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeceeeeeeseeaeeeeeeceeeeseceeeeeeesseeneeeseees 88 Chapter 14 System Log Commande ss seennneneeseeeeennr ntt neenrrrrt rtt tnrrrnnnrr rnrn rerennn 89 fe eise E OS 89 LOGGING Te ash RA A A AAA AAA Na RR aR aae 90 logging file flash frequency ccoocoonoccccnonocccccnnonccnnononcnononnnnnnnnnnnnnnnnnnnnncnnnnnnnnnn nan nnnnniannnnncnnnannss 90 loggingfileashilevel voii a 91 clear logging RE 91 logging hostinde X tee aaa 92 show logging ocal config rr EnEnEE Eneee Enee 93 SHOW JOGGING IOGHOS TEEN 93 Gleef DEE 94 show logging ash cin es 94 Chapter 15 SSH EEN 96 ipssh server O 96 E A EE EE E dace ceca cece ceencececnsasiee 96 IP SSHACIM COUP nesia e a e vei e E EEE AEAEE A ee 97 E client irii NN 97 PESO DOWN AA eones 98 Ne dee SV AAA A AAA RARA AAA ERA AAA 98 C
85. apter 23 Port Isolation Commands oooooonccccccccccocononnnnncnonnnonononnnnnnnncnnnnnnnnnnnnnns 154 POF ISOIAUON e na NS 154 show port isolation interface cccccccceceeeeeeeeeeeeeeeeeeeeeeeesecaeeeeeeceeeeeeeneeeeesseaeeeeseeeeieeeeeeees 154 Chapter 24 Loopback Detection Commands occcccccccnnnncncnccnnnnnonnnnnnnnnncnnnnnnnnnnnnnns 156 Joopback detechontglobal AA 156 VIII loopback detection Internal 156 loopback detection recOVery tiMe ccccecccceeeeeeneeeeceeneeeeeeeeeeeeeeecaeeeeseneeeeseseeeeeeseeaeaeeeeenas 157 Joopback detechont iniertace A 157 I0opback detection Co EE 158 Ibopback detection ee E 158 show loopback detection global 159 show loopback detection interface oooooococcnnnccccnnnnoccccnonoccncnonancnnnnnnncnnnonnnnnononnannncnnnannnccncnnnss 159 Chapter 25 PoE Commands atinado ai did Als dd Aa 161 power inline consumption global ooooconncccc nncocccncnnncccnonononcnnonnnncccnnnncnn conan cnn ncnnnnnnncnnannss 161 power inline disconnect method A 161 Power profile meen e aaa aaa 162 POWER TIMO TANGE TT 163 p wer holiday cuicos cia iii 164 O EE 164 Ne le 165 holiday enee EE 166 power inline Consumptioniintertace nrn nene 166 power inline priority TE E a a a a aa aaae a aa e aeai 167 power inline SUPPlYiviiaidadao datada AREE EE EEE ece cece cxennece cena 168 power inline profile eee ee verter eek aaa a ta 168 POWER INNING TIME LANG O aiaeeiiee eee i a a ates RENE 169 SHOW PO
86. ault Command Mode Privileged EXEC Mode and Any Configuration Mode 94 Example Display the log information with the level marked 0 3 in the log file TL SG3424 config show logging flash level 3 95 Chapter 15 SSH Commands SSH Security Shell can provide the unsecured remote management with security and powerful authentication to ensure the security of the management information ip ssh server Description The ip ssh server command is used to enable SSH function To disable the SSH function please use no ip ssh server command Syntax ip ssh server no ip ssh server Command Mode Global Configuration Mode Example Enable the SSH function TL SG3424 config ip ssh server ip ssh version Description The ip ssh version command is used to enable the SSH protocol version To disable the protocol version please use no ip ssh version command Syntax ip ssh version v1 v2 no ip ssh version v1 v2 Parameter v1 v2 The SSH protocol version to be enabled They represent SSH vi and SSH v2 respectively Command Mode Global Configuration Mode 96 Example Enable SSH v2 TL SG3424 config ip ssh version v2 ip ssh timeout Description The ip ssh timeout command is used to specify the idle timeout time of SSH To restore to the factory defaults please use ip ssh timeout command Syntax ip ssh timeout value no ip ssh timeout Parameter value The ldle timeout time During this period t
87. authorized force In this mode the port is forbidden working for its fixed unauthorized status Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the Control Mode for port 1 as authorized force TL SG3424 config interface gigabitEthernet 1 0 1 TL SG3424 config if dot1x port control authorized force dot1x port method Description The dot1x port method command is used to configure the control type of IEEE 802 1X for the specified port By default the control type is mac based To restore to the default configuration please use no dot1x port method command Syntax dot1x port method mac based port based no dot1x port method Parameter mac based port based The control type for the port mac based Any client connected to the port should pass the 802 1X authentication for access 84 port based All the clients connected to the port can access the network on the condition that any one of the clients has passed the 802 1X Authentication Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the Control Type for port 1 as port based TL SG3424 config interface gigabitEthernet 1 0 1 TL SG3424 config if dot1x port method port based radius Description The radius command is used to configure the parameters of radius Syntax radius au
88. ax access list bind policy name no access list bind policy name Parameter policy name The name of the policy desired to bind Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Bind policy1 to port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if access list bind policy1 183 access list bind vlan Description The access list bind command is used to bind a policy to a VLAN To cancel the bind relation please use no access list bind command Syntax access list bind policy name no access list bind policy name Parameter policy name The name of the policy desired to bind Command Mode Interface VLAN Mode Example Bind policy1 to VLAN 2 TL SG3424 config interface vlan 2 TL SG3424 config if access list bind policy1 show time range Description The show time range command is used to display the configuration of Time Range Syntax show time range Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Time Range TL SG3424 config show time range show holiday Description The show holiday command is used to display the defined holiday 184 Syntax show holiday Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the defined holiday TL SG3424 config show holiday show access list Description The show ac
89. ay nationalday start date 10 01 end date 10 03 access list create Description The access list create command is used to create standard IP ACL and extend IP ACL Syntax access list create access list num Parameter access list num ACL ID ranging from 100 to 299 The ID range of Standard IP ACL ranges is 100 199 and the Extend IP ACL is 200 299 Command Mode Global Configuration Mode Example Create a standard IP ACL whose ID is 123 TL SG3424 config access list create 123 mac access list Description The mac access list command is used to create MAC ACL To set the detailed configurations for a specified MAC ACL please use mac access list command to access Mac Access list Configuration Mode To delete the MAC ACL please use no mac access list Syntax mac access list access list num no mac access list access list num Parameter access list num ACL ID ranging from 0 to 99 Command Mode Global Configuration Mode 175 Example Create a MAC ACL whose ID is 23 TL SG3424 config mac access list 23 access list standard Description The access list standard command is used to add Standard IP ACL rule To delete the corresponding rule please use no access list standard command Standard IP ACLs analyze and process data packets based on a series of match conditions which can be the source IP addresses and destination IP addresses carried in the packets Syntax access list standard acl id ru
90. bitEthernet interface range gigabitEthernet Example Enable Port Security function for port 1 select Static mode as the learn mode and specify the maximum number of MAC addresses that can be learned on this port as 30 TL SG3424 config interface gigabitEthernet 1 0 1 TL SG3424 config if f mac address table max mac count max number 30 mode static status enable show mac address table Description The show mac address table command is used to display the information of all Address entries Syntax show mac address table dynamic static drop all Parameter dynamic static drop all The type of your desired entry Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of all Address entries TL SG3424 config show mac address table all show mac address table aging time Description The show mac address table aging time command is used to display the Aging Time of the MAC address Syntax show mac address table aging time Command Mode Privileged EXEC Mode and Any Configuration Mode 106 Example Display the Aging Time of the MAC address TL SG3424 config show mac address table aging time show mac address table max mac count interface gigabitEthernet Description The show mac address table max mac count interface gigabitEthernet command is used to display the security configuration of all ports or the specified port Syntax show mac address
91. both the user name password and user name secret are defined you must enter the password set in user name secret 2 If you change the password of the current user in a telnet or console connection the connection will be cut off and the newly configured password is required for the re login Example Add and enable a new admin user named tplink of which the password is admin The password will be displayed in the encrypted form TL SG3424 config user name tplink privilege admin secret 0 admin user access control ip based Description The user access control ip based command is used to limit the IP range of the users for login Only the users within the IP range you set here are allowed to login To cancel the user access limit please use no user access control command Syntax user access control ip based p addr ip mask no user access control Parameter ip addr The source IP address Only the users within the IP range you set here are allowed for login ip mask The subnet mask of the IP address 53 Command Mode Global Configuration Mode Example Enable the access control of the user whose IP address is 192 168 0 148 TL SG3424 config user access control ip based 192 168 0 148 255 255 255 255 user access control mac based Description The user access control mac based command is used to limit the MAC Address of the users for login Only the user with this MAC Address yo
92. cess list command is used to display configuration of ACL Syntax show access list acl id Parameter acl id The ID of the ACL selected to display the configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the MAC ACL whose ID is 20 TL SG3424 config show access list 20 show access list policy Description The show access list policy command is used to display the information of a specified policy Syntax show access list policy name Parameter name The Policy Name desired to show Command Mode Privileged EXEC Mode and Any Configuration Mode 185 Example Display the information of a policy named policy1 TL SG3424 config show access list policy policy1 show access list bind Description The show access list bind command is used to display the configuration of Policy bind Syntax show access list bind Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Policy bind TL SG3424 config show access list bind 186 Chapter 27 MSTP Commands MSTP Multiple Spanning Tree Protocol compatible with both STP and RSTP and subject to IEEE 802 1s can disbranch a ring network STP is to block redundant links and backup links as well as optimize paths spanning tree global Description The spanning tree command is used to enable STP function globally To disable the STP function please use
93. cluster candidate command is used to specify the current switch as candidate switch Syntax cluster candidate Command Mode Global Configuration Mode Example Specify the current switch as candidate switch TL SG3424 config cluster candidate cluster individual Description The cluster individual command is used to specify the current switch as individual switch Syntax cluster individual Command Mode Global Configuration Mode 263 Example Specify the current switch as individual switch TL SG3424 config cluster individual show cluster ndp Description The show cluster ndp command is used to display NDP configuration of certain ports Syntax show cluster ndp interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the NDP global configuration TL SG3424 show cluster ndp Display the NDP configuration of all Ethernet ports TL SG3424 show cluster ndp interface Display the NDP configuration of port 2 TL SG3424 show cluster ndp interface gigabitEthernet 1 0 2 show cluster ntdp Description The show cluster ntdp command is used to display NTDP configuration or the information of device collected through NTDP Syntax show cluster ntdp interface gigabitEthernet port device list Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configura
94. cp port priority 2048 show etherchannel Description The show etherchannel command is used to display the EtherChannel information 48 Syntax show etherchannel channel group num detail summary Parameter channel group num The EtherChannel Group number ranging from 1 to 8 By default it is empty and will display the information of all EtherChannel Groups detail The detailed information of EtherChannel summary The EtherChannel information in summary Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the detailed information of EtherChannel Group 1 TL SG3424 config show etherchannel 1 detail show etherchannel load balance Description The show etherchannel load balance command is used to display the Aggregate Arithmetic of LAG Syntax show etherchannel load balance Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Aggregate Arithmetic of LAG TL SG3424 config show etherchannel load balance show lacp Description The show lacp command is used to display the LACP information for a specified EtherChannel Group Syntax show lacp channel group num internal neighbor 49 Parameter channel group num The EtherChannel Group number ranging from 1 to 8 By default it is empty and will display the information of all LACP groups internal The internal LACP information neighbor
95. cription The ip igmp snooping filter mode command is used to configure the Action mode for the desired port 209 Syntax ip igmp snooping filter mode mode Parameter mode Action Mode with refuse and accept options Refuse indicates only the multicast packets whose multicast IP is not in the IP range will be processed while accept indicates only the multicast packets whose multicast IP is in the IP range will be processed By default the option is accept Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the Action Mode as accept for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if ip igmp snooping filter mode accept show ip igmp snooping Description The show ip igmp snooping command is used to display the global configuration of IGMP snooping Syntax show ip igmp snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of IGMP TL SG3424 show ip igmp snooping show ip igmp snooping interface Description The show ip igmp snooping interface command is used to display the port configuration of IGMP snooping 210 Syntax show ip igmp snooping interface gigabitEthernet port port list basic config filter packet stat Parameter port The Ethernet port number port list The list of Ethernet ports basic config filter
96. d In Global Configuration Mode you can configure password for Admin level by enable password command Once password is configured you are required to enter it to access Privileged EXEC mode 1 4 Conventions 1 4 1 Format Conventions The following conventions are used in this Guide gt Items in square brackets are optional gt Items in braces are required gt Alternative items are grouped in braces and separated by vertical bars For example speed 10 100 1000 gt Bold indicates an unalterable keyword For example show logging 18 Normal Font indicates a constant several options are enumerated and only one can be selected For example switchport type access trunk general Italic Font indicates a variable an actual value must be assigned For example bridge aging time aging time 1 4 2 Special Characters You should pay attentions to the description below if the variable is a character string gt gt These six characters lt gt 18 cannot be input If a blank is contained in a character string single or double quotation marks should be used for example hello world hello world and the words in the quotation marks will be identified as a string Otherwise the words will be identified as several strings 1 43 Parameter Format Some parameters must be entered in special formats which are shown as follows gt gt MAC Address must be entered in the forma
97. d LLDP MED fast start repeat count number Syntax show lldp Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of LLDP and LLDP MED fast start repeat count number TL SG3424P show Ildp show Ildp interface Description The show Ildp interface command is used to display LLDP and LLDP MED configuration of the corresponding port By default the configuration of all the ports will be displayed Syntax show Ildp interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP and LLDP MED configuration of port 1 TL SG3424P show lldp interface gigabitEthernet 1 0 1 257 show lidp local information interface Description The show lldp local information interface command is used to display the LLDP and LLDP MED local information of the corresponding port By default the information of all the ports will be displayed Syntax show Ildp local information interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP and LLDP MED local information of port 1 TL SG3424P show lldp local information interface gigabitEthernet 1 0 1 show lldp neighbor information interface Description The show lldp neighbor information interface com
98. d is used to configure Direction function of policy action for specified VLAN Syntax redirect vlan vian id Parameter vian id The VLAN ID of Redirect The data packets matching the corresponding ACL will be forwarded in the specific VLAN The VLAN ID ranges from 1 to 4094 Command Mode Action Configuration Mode Example Edit the actions for policy1 Forward the data packets matching ACL 120 in the policy to Fast Ethernet VLAN 1 TL SG3424 config access list policy action policy1 120 TL SG3424 config action redirect vlan 1 s condition Description The s condition command is used to configure Stream Condition function of policy action Syntax s condition rate rate osd none discard Parameter rate The rate of Stream Condition ranging from 0 to 100000kbps 181 osd Out of Band disposal of Stream Condition It is the disposal way of the data packets those are transmitted beyond the rate There are two options none and discard By default the option is none Command Mode Action Configuration Mode Example Edit the actions for policy1 For the data packets matching ACL 120 in the policy if the rate beyond 1000kbps they will be discarded by the switch TL SG3424 config access list policy action policy1 120 TL SG3424 config action s condition rate 1000 osd discard s mirror Description The s mirror command is used to configure Stream Mirror function of policy action to the specified por
99. d is used to display the cable diagnostics of the connected Ethernet Port which facilitates you to check the connection status of the cable connected to the switch locate and diagnose the trouble spot of the network Syntax show cable diagnostics interface gigabitEthernet port Parameter port The number of the port which is selected for Cable test Command Mode 125 Privileged EXEC Mode and Any Configuration Mode Example Show the cable diagnostics of port 3 TL SG3424 show cable diagnostics interface gigabitEthernet 1 0 3 126 Chapter 19 IPv6 Address Configuration Commands The IPv6 address configuration commands are provided in the Interface VLAN Mode Type enable configure interface vlan vian id to enter the Interface Configuration Mode of the management VLAN By default the management VLAN is VLAN1 You can use the command ip management vlan v an id in the Global Configuration Mode to configure the management VLAN ipv6 enable Description Syntax This command is used to enable the IPv6 function globally The IPv6 function should be enabled before the IPv6 address configuration management By default it is enabled If the IPv6 function is disabled the corresponding IPv6 netstack and IPv6 based modules will be invalid for example SSHv6 SSLv6 TFTPv6 etc To disable the IPv6 function please use no ipv6 enable command ipv6 enable no ipv6 enable Command Mode Interface Configuration Mode
100. de Global Configuration Mode Example Configure the Aggregate Arithmetic for LAG as src dst mac TL SG3424 config port channel load balance src dst mac lacp system priority Description The lacp system priority command is used to configure the LACP system priority globally To return to the default configurations please use no lacp system priority command Syntax lacp system priority pri no lacp system priority Parameter pri The system priority ranging from O to 65535 It is 32768 by default 47 Command Mode Global Configuration Mode Example Configure the LACP system priority as 1024 globally TL SG3424 config lacp system priority 1024 lacp port priority Description The lacp port priority command is used to configure the LACP port priority for specified ports To return to the default configurations please use no lacp port priority command Syntax lacp port priority pri no lacp port priority Parameter pri The port priority ranging from 0 to 65535 It is 32768 by default Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the LACP port priority as 1024 for ports 1 3 TL SG3424 config interface range gigabitEthernet 1 0 1 3 TL SG3424 config if range lacp port priority 1024 Configure the LACP port priority as 2048 for port 4 TL SG3424 config interface gigabitEthernet 1 0 4 TL SG3424 config if la
101. defend function for ports 2 6 TL SG3424 config interface range gigabitEthernet 1 0 2 6 TL SG3424 config if range ip arp inspection 73 ip arp inspection limit rate Description The ip arp inspection limit rate command is used to configure the ARP speed of a specified port To restore to the default speed please use no ip arp inspection limit rate command Syntax ip arp inspection limit rate value no ip arp inspection limit rate Parameter value The value to specify the maximum amount of the received ARP packets per second ranging from 10 to 100 in pps packet second By default the value is 15 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the maximum amount of the received ARP packets per second as 50 pps for port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if ip arp inspection limit rate 50 ip arp inspection recover Description The ip arp inspection recover command is used to restore to the port to the ARP transmit status from the ARP filter status Syntax ip arp inspection recover Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet 74 Example Restore port 5 to the ARP transmit status TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if ip arp inspection recover show ip arp inspection Description
102. dot1x auth method pap dot1x guest vlan global Description The dot1x guest vlan command is used to enable the Guest VLAN function globally To disable the Guest VLAN function please use no dot1x guest vlan command Syntax dot1x guest vlan vid no dot1x guest vlan Parameter vid The VLAN ID needed to enable the Guest VLAN function ranging from 1 to 4094 The supplicants in the Guest VLAN can access the specified network source Command Mode Global Configuration Mode Example Enable the Guest VLAN function for VLAN 5 TL SG3424 config dot1x guest vlan 5 80 dot1x quiet period Description The dot1x quiet period command is used to enable the quiet period function To disable the function please use no dot1x quiet period command Syntax dot1x quiet period no dot1x quiet period Command Mode Global Configuration Mode Example Enable the quiet period function TL SG3424 config dot1x quiet period dot1x timeout Description The dot1x timeout command is used to configure the quiet period and the supplicant timeout To restore to the default please use no dot1x timeout command Syntax dot1x timeout quiet period time reauth period time no dot1x timeout quiet period reauth period Parameter quiet period time The value for Quiet Period ranging from 1 to 999 in seconds By default it is 10 Once the supplicant failed to the 802 1X Authentication then the switch will no
103. e Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the PoE information of the system TL SG3424P show power inline 169 show power inline configuration interface Description The show power inline configuration interface command is used to display the PoE configuration of the certain port Syntax show power inline configuration interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the PoE configuration of all ports TL SG3424P show power inline configuration interface show power inline information interface Description The show power inline information command is used to display the PoE information of the certain port Syntax show power inline information interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the POE information of all ports TL SG3424P show power inline information interface show power profile Description The show power profile command is used to display the defined PoE profile 170 Syntax show power profile Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the defined PoE profile TL SG3424P show power profile show power holiday Description The show power holiday command is used to display the defin
104. e VLANs and adding the ports with voice devices attached to voice VLANs you can perform QoS related configuration for voice data ensuring the transmission priority of voice data stream and voice quality voice vian Description The voice vlan command is used to enable Voice VLAN function To disable Voice VLAN function please use no voice vlan command Syntax voice vlan vian id no voice vlan Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 2 to 4094 Command Mode Global Configuration Mode Example Enable the Voice VLAN function for VLAN 10 TL SG3424 config voice vlan 10 voice vian aging time Description The voice vlan aging time command is used to set the aging time for a voice VLAN To restore to the default aging time for the Voice VLAN please use no voice vlan aging time command By default the aging time is 1440 minutes Syntax voice vlan aging time time no voice vlan aging time 37 Parameter time Aging time in minutes to be set for the Voice VLAN It ranges from 1 to 43200 Command Mode Global Configuration Mode Example Set the aging time for the Voice VLAN as 1 minute TL SG3424 config voice vlan aging time 1 voice vlan priority Description The voice vlan priority command is used to configure the priority for the Voice VLAN To restore to the default priority please use no voice vlan priority command By default the priority value is 6 Syntax v
105. e specified Log Host please use no logging host index command Log Host is to receive the system log from other devices You can remotely monitor the settings and operation status of other devices through the log host Syntax logging host index dx host ip level no logging host index dx Parameter idx The index of the log host The switch supports 4 log hosts at most host ip The IP for the log host level The severity level of the log information sent to each log host There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be sent to the corresponding log host By default it is 6 indicating that the log information marked with 0 6 will be sent to the log host Command Mode Global Configuration Mode 92 Example Set the IP address as 192 168 0 148 the level 5 TL SG3424 config logging host index 2 192 168 0 148 5 show logging local config Description The show logging local config command is used to display the configuration of the Local Log including the log buffer and the log file Syntax show logging local config Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the Local Log TL SG3424 config show logging local config show logging loghost Description The show logging loghost command is used to display the configuration of the
106. e the ports SNMP notification please use no Ildp snmp trap command 253 Syntax lldp snmp trap no Ildp snmp trap Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the SNMP notification for port 1 TL SG3424P config interface gigabitEthernet 1 0 1 TL SG3424P config if Ildp snmp trap Ildp tlv select Description The Ildp tlv select command is used to configure TLVs to be included in outgoing LLDPDU To exclude TLVs please use no Ildp tlv select command By default All TLVs are included in outgoing LLDPDU Syntax lldp tlv select port description system capability system description system name management address port vlan protocol vlan vlan name link aggregation mac phy cfg max frame size power all no Ildp tlv select port description system capability system description system name management address port vlan protocol vlan vlan name link aggregation mac phy cfg max frame size power all Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Exclude management address and port vlan id TLVs in LLDPDU outgoing from port 1 TL SG3424P config interface gigabitEthernet 1 0 1 TL SG3424P config if no Ildp tlv select management address port vlan 254 Ildp med location Description The lldp med location comma
107. eb Mar Apr May Jun Jul Aug Sep Oct Nov Dec stime Time to start in the format of hh mm eweek Week to end with options first second third fourth last eday Day to end with options Sun Mon Tue Wed Thu Fri Sat emonth Month to end with options Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec etime Time to end in the format of hh mm offset Specify the time adding in minutes when Daylight Saving Time comes The range of value depends and the default value is 60 minutes It is optional Command Mode Global Configuration Mode Example Specify the DST start time of the switch as 2 00 am on the first Sunday in May the end time as 2 00 am on the last Sunday in October and the offset as 45 minutes TL SG3424 config system time dst recurring first Sun May 02 00 last Sun Oct 02 00 45 114 hostname Description The hostname command is used to configure the system name To clear the system name information please use no hostname command Syntax hostname hostname no hostname Parameter hostname System Name The length of the name ranges from 1 to 32 characters By default it is the device name for example TL SG3424 Command Mode Global Configuration Mode Example Configure the system name as TPLINK TL SG3424 config hostname TPLINK location Description The location command is used to configure the system locatio
108. ed periodic time occurs To delete the corresponding periodic mode time range configuration please use no periodic command Syntax periodic week date week day time slice1 fime slice time slice2 time slice time slice3 time slice time slice4 time slice no periodic week date time slice Parameter week day Periodic Mode with 1 7 daily off day and working day options 1 7 should be entered in the format of 1 3 7 which represent Monday Tuesday Wednesday and Sunday Daily represents every day Off day represents weekend Working day represents working day time slice Create time slice in the format of HH MM HH MM Command Mode Power Time range Create Configuration Mode Example Configure the PoE time range named tRange2 as a periodic time range and 165 specify the date and time as 8 30 to 12 00 on weekends TL SG3424P config power time range tRange2 TL SG3424P config pwr time range periodic week date off day time slice1 08 30 12 00 holiday Description The holiday command is used to create holiday mode time range for the PoE time range of the switch When the PoE holiday which is excluded from PoE time range occurs the switch will not supply power Syntax holiday exclude include Parameter exclude Indicates the PoE time range of the switch excluding the PoE holiday When PoE holiday occurs the switch will not su
109. ed PoE holiday Syntax show power holiday Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the defined PoE holiday TL SG3424P show power holiday show power time range Description The show power time range command is used to display the configuration of POE time range Syntax show power time range Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of PoE time range TL SG3424P show power time range 171 Chapter 26 ACL Commands ACL Access Control List is used to filter data packets by configuring a series of match conditions operations and time ranges It provides a flexible and secured access control policy and facilitates you to control the network security time range Description The time range command is used to add Time Range To delete the corresponding Time Range please use no time range command A time range based ACL enables you to implement ACL control over packets by differentiating the time ranges A time range can be specified in each rule in an ACL The rule takes effect only when the specified time range is configured and the system time is within the time range Syntax time range name no time range name Parameter name The Time Range name ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add a time range named tSeg1 TL SG3424 config time range tSeg1 absolute Descri
110. ed on DSCP priority mode non IP datagram with IEEE 802 1Q tag are mapped to different priority levels based on IEEE 802 1P priority mode if IEEE 802 1P Priority is enabled the untagged non IP datagram are mapped based on port priority mode Syntax qos queue dscp map dscp list y cos id no qos queue dscp map Parameter dscp list List of DSCP value One or several DSCP values can be typed using comma to separate Use a hyphen to designate a range of values for instance 1 4 7 11 indicates choosing 1 4 5 6 7 11 The DSCP value ranges from 0 to 63 cos id The priority level the packets with tag are mapped to which ranges from CoS 0 to CoS 7 Command Mode Global Configuration Mode 146 User Guidelines By default the mapping relation between tag and the egress queue is 0 7 CoS 0 8 15 CoS 1 16 23 CoS 2 24 31 CoS 3 32 39 CoS 4 40 47 CoS 5 48 55 CoS 6 56 63 CoS 7 Example Map DSCP values 10 12 to CoS 2 TL SG3424 config qos queue dscp map 10 12 2 qos queue mode Description The qos queue mode command is used to configure the Schedule Mode To return to the default configuration please use no qos queue mode command When the network is congested the program that many packets complete for resources must be solved usually in the way of queue scheduling The switch will control the forwarding sequence of the packets according to the priority queues and scheduling algorithms you set On this
111. eives IGMP report message it examines the multicast filtering IP ID configured on the access port to determine if the port can join the multicast group If the multicast IP is not filtered the switch will add the port to the forward port list of the multicast group Otherwise the switch will drop the IGMP report message In that way you can control the multicast groups that users Can access 208 Syntax ip igmp snooping filter no ip igmp snooping filter Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable IGMP Snooping filter function for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if ip igmp snooping filter ip igmp snooping filter maxgroup Description The ip igmp snooping filter maxgroup command is used to specify the maximum number of multicast groups for a port to join in Syntax ip igmp snooping filter maxgroup maxgroup Parameter maxgroup The maximum number of multicast groups for a port to join in It is used to prevent some ports taking up too much bandwidth Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the maximum number of multicast groups for ports 2 5 to join in as 10 TL SG3424 config interface range gigabitEthernet 1 0 2 5 TL SG3424 config if range ip igmp snooping filter maxgroup 10 ip igmp snooping filter mode Des
112. enable Secret EE 22 E le 23 Ell Mari A 23 lui A A A EEE ee 23 QI DT 24 DIST AAA A AA AA AAA A A A A AAA AAA AAA A 24 history cleat ici See een ceva eaves en A eevee oh ce Tn ee Tn A ee vee 25 Chapter3 IEEE 802 1Q VLAN Commands ccccoooccnnncnnncccnncnnnnnnnnnnnnnnnnnnnnnnnnnnnononons 26 VII ura AAA EEE EA ee 26 line En NET 26 MEHR 27 Gelee ue 27 SWitchport ACCESS VIAN EE 28 switchport trunk allowed van 28 switchport general allowed van 29 A a a o 30 Nee EE ul In EE 30 SHOW WiAN EE 31 Ge a EN Chapter4 MAC based VLAN Commands cceceeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeees 32 mac vlan mac address tell 32 show MAC Vanes te Phi te eet ee a 32 Chapter5 Protocol based VLAN Commande 34 protocol ER ul E 34 PFOLOCOIEVI AN Va mytaro Ee En case cavecdeecevesdveceveccvectev EE E EEEE E TOAA 35 protocollari Eet re Te EE 35 show protocol vlan template AAA 36 show protocol Wlan van 36 Chapters Voice VLAN CommandS cuina eii 37 VOICE EE 37 VOICE Vian AGING EL 37 VOICE VIAN DIONLY ah cho Oe A et e a ened 38 MEE 38 switchport Voice Vian MOG veronica 39 switchportvolce vlan SecUl Viven seen ieee NO 40 SHOW VOICE EI VT 40 SHOW VOICE VIAN e ET 41 show voice vlan switchport cccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeceeeeeeeeaeeeeeeceeeeseeesneeeeeeeieeeesenes 41 Chapter 7 GVRP Commands EES 42 OVID GlOBall src nee ne erie ieee eer A Aaa 42 eise ET 42 eis FEGISTFALION TTT 43 OVP UL AY at A A ente 43
113. erface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable SNMP link status trap for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424P config if snmp server traps link status snmp server traps Description The snmp server traps command is used to enable SNMP extended traps To disable the sending of SNMP extended traps please use no snmp server traps command Syntax snmp server traps bandwidth control cpu flash ipaddr change Ildp loopback detection storm control spanning tree memory no snmp server traps bandwidth control cpu flash ipaddr change Ildp loopback detection storm control spanning tree memory Parameter bandwidth control Enable bandwidth control trap It is sent when the rate limit function is enabled and the bandwidth exceeds the predefined value cpu Allow CPU related trap It is sent when CPU usage exceeds the predefined threshold By default the CPU usage threshold of the switch is 80 flash Enable flash trap It is sent when flash is modified during operations such as backup reset firmware upgrade configuration import etc ipaddr change Enable ipaddr change trap It is sent when IP address is changed such as user manually modifies the IP address or the switch obtains a new IP address from DHCP Ildp Enable lldp trap It is sent when the ports neighbor chang
114. es loopback detection Enable loopback detection trap It is sent when the switch detects loopback or loopback is cleared 239 storm control Enable storm control trap lt is sent when the multicast or broadcast rate exceeds the predefined value spanning tree Enable spanning tree trap It is sent when the port forwarding status changes or the port receives TCN packet or packet with TC flag memory Enable memory trap It is sent when CPU usage exceeds 80 Command Mode Global Configuration Mode Example Enable SNMP extended bandwidth control trap for the switch TL SG3424 config snmp server traps bandwidth control snmp server traps mac Description The snmp server traps mac command is used to enable SNMP extended MAC address related traps which include four types new full learn mode change and max learned To disable the sending of SNMP extended MAC address related traps please use no snmp server traps mac command Syntax snmp server traps mac new full learn mode change max learned no snmp server traps mac new full learn mode change max learned Parameter new Enable new MAC address trap It is sent when the switch learns new MAC address including dynamic address static address and filter address full Enable MAC address table trap It is sent when the MAC address table is full learn mode change Enable MAC address learn mode change trap It is
115. es in a file in the flash on the switch To disable the log file flash function please use no logging file flash command The log file flash indicates the flash sector for saving system log The information in the log file of the flash will not be lost after the switch is restarted and can be got by the show logging flash command Syntax logging file flash no logging file flash Command Mode Global Configuration Mode Example Enable the log file flash function TL SG3424 config logging file flash logging file flash frequency Description The logging file flash frequency command is used to specify the frequency to synchronize the system log file in the log buffer to the flash To resume the default synchronizing frequency please use the no logging file flash frequency command Syntax logging file flash frequency periodic periodic immediate no logging file flash frequency Parameter periodic The frequency to synchronize the system log file in the log buffer to the flash ranging from 1 to 48 hours By default the synchronization process takes place every 24 hours immediate The system log file in the buffer will be synchronized to the flash immediately This option will reduce the life of the flash and is not recommended 90 Command Mode Global Configuration Mode Example Specify the log file synchronization frequency as 10 hours TL SG3424 config logging file flash frequency periodic10 logg
116. ess for tracert test should be IPv4 ipv6 The type of the IP address for tracert test should be IPv6 ip_addr The IP address of the destination device If the parameter ip ipv6 is not selected both IPv4 and IPv6 addresses are supported for example 192 168 0 100 or fe80 1234 maxHops The maximum number of the route hops the test data can pass though It ranges from 1 to 30 By default this value is 4 Command Mode User EXEC Mode and Privileged EXEC Mode Example Test the connectivity between the switch and the network device with the IP 192 168 0 131 If the destination device has not been found after 20 maxHops the connection between the switch and the destination device is failed to establish TL SG3424 tracert 192 168 0 131 20 Test the connectivity between the switch and the network device with the IP fe80 1234 If the destination device has not been found after 20 maxHops the connection between the switch and the destination device is failed to establish TL SG3424 tracert fe80 1234 20 show system time Description The show system time command is used to display the current time system and its source Syntax show system time Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the time information of the switch TL SG3424 show system time 123 show system time dst Description The show system time dst command is used to display the DST time informa
117. eway To restore to the factory defaults please use no ip address command This command should be configured in the Interface Configuration Mode of the management VLAN Syntax ip address ip addr ip mask gateway no ip address Parameter ip addr The system IP of the switch The default system IP is 192 168 0 1 ip mask The Subnet Mask of the switch The default Subnet Mask is 255 255 255 0 gateway The Default Gateway of the switch By default it is empty Command Mode Interface Configuration Mode interface vian Example Configure the system IP as 192 168 0 69 and the Subnet Mask as 255 255 255 0 when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ip address 192 168 0 69 255 255 255 0 ip address alloc dhcp Description The ip address alloc dhcp command is used to enable the DHCP Client function When this function is enabled the switch will try to obtain IP from DHCP server This command should be configured in the Interface Configuration Mode of the management VLAN Syntax ip address alloc dhcp Command Mode Interface Configuration Mode interface vian 117 Example Enable the DHCP Client function when the management VLAN of the switch is VLAN1 TL SG3424 config interface vlan 1 TL SG3424 config if ip address alloc dhcp ip address alloc bootp Description The ip address alloc bootp command is used to enable the BOOTP Protocol
118. exit or the command to Mod g port list command to TL SG3424 return to Global Configuration mode ode Se enter this mode from config if range A port number must be specified in the Global Configuration interface command mode VLAN Use the vlan vlan list Use the end command or press Ctrl Z Configuration command to enter this TL SG3424 to return to Privileged EXEC mode Mod mode from Global config vlan Enter the exit or the command to Ges Configuration mode return to Global configuration mode Note 1 The user is automatically in User EXEC Mode after the connection between the PC and the switch is established by a console port or by a telnet connection 2 Each command mode has its own set of specific commands To configure some commands you should access the corresponding command mode firstly e Global Configuration Mode In this mode global commands are provided such as the Spanning Tree Schedule Mode and so on Interface Configuration Mode In this mode users can configure one or several ports different ports corresponds to different commands a Interface gigabitEthernet Configure parameters for an Ethernet port such as Duplex mode flow control status Interface range gigabitEthernet The commands contained are the same as that of the Interface gigabiteEthernet Configure parameters for several Ethernet ports Interface link aggregation Configure parameters for a link aggregation such as
119. fault 0 Specify the encryption type O indicates that an unencrypted password will follow By default the encryption type is 0 password Users login password a string from 1 to 31 alphanumeric characters or symbols The password is case sensitive allows digits English letters case sensitive underlines and sixteen special characters 15 0 KI By default it is empty 7 Indicates a symmetric encrypted password with fixed length will follow encrypted password A symmetric encrypted password with fixed length which you can copy from another switch s configuration file After the encrypted password is configured you should use the corresponding unencrypted password if you re enter this mode Command Mode Global Configuration Mode 51 User Guidelines 1 If the password you configured here is unencrypted and the global encryption function is enabled in service password encryption the password in the configuration file will be displayed in the symmetric encrypted form 2 If you change the password of the current user in a telnet or console connection the connection will be cut off and the newly configured password is required for the re login Example Add and enable a new admin user named tplink of which the password is admin and unencrypted TL SG3424 config user name tplink privilege admin password 0 admin user name secret Description The user name comm
120. figured if you select this option You can only select the trap type in Security Model v1 By default the type of the notifications is trap retries The amount of times the switch retries an inform request ranging from 1 to 255 The switch will resend the inform request if it doesn t get the response from the management station during the Timeout interval and it will terminate resending the inform request if the resending times reach the specified Retry times timeout The maximum time for the switch to wait for the response from the management station before resending a request ranging from 1 to 3600 in seconds Command Mode Global Configuration Mode Example Add a Notification entry and configure the IP Address of the management Host as 192 168 0 146 the UDP port as 162 the User name of the management station as admin the Security Model of the management station as v2c the type of the notifications as inform the maximum time for the switch to wait as 1000 seconds and the retries time as 100 TL SG3424 config snmp server host 192 168 0 146 162 admin smode v2c type inform retries 100 timeout 1000 236 Add a Notification entry and configure the IP Address of the management Host as fe80 1234 the UDP port as 162 the User name of the management station as admin the Security Model of the management station as v2c the type of the notifications as inform the maximum time for the switch to wait as 1000 seco
121. g show voice vlan oui show voice vian switchport Description The show voice vlan switchport command is used to display the Voice VLAN configuration information of all ports or a specified port Syntax show voice vlan switchport gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Voice VLAN configuration information of all ports TL SG3424 config show voice vlan switchport Display the Voice VLAN configuration information of port 2 TL SG3424 config show voice vlan switchport gigabitEthernet 1 0 2 41 Chapter7 GVRP Commands GVRP GARP VLAN registration protocol is an implementation of GARP generic attribute registration protocol GVRP allows the switch to automatically add or remove the VLANs via the dynamic VLAN registration information and propagate the local VLAN registration information to other switches without having to individually configure each VLAN gvrp global Description The gvrp command is used to enable the GVRP function globally To disable the GVRP function please use no gvrp command Syntax gvrp no gvrp Command Mode Global Configuration Mode Example Enable the GVRP function globally TL SG3424 config gvrp gvrp interface Description The gvrp command is used to enable the GVRP function for the desired port To disable the GVRP function of this port please use no gvrp
122. gin numbers please use no user max number command Syntax user max number admin num guest num no user max number Parameter admin num The maximum number of the users allowed to log on as Admin ranging from 1 to 16 The total number of Admin and Guest should be less than 16 guest num The maximum number of the users allowed to log on as Guest ranging from 0 to 15 The total number of Admin and Guest should be less than 16 Command Mode Global Configuration Mode 55 Example Configure the maximum number of users login as Admin and Guest as 5 and 3 TL SG3424 config user max num 5 3 user idle timeout Description The user idle timeout command is used to configure the timeout time of the switch To restore to the default timeout time please use no user idle timeout command Syntax user idle timeout minutes no user idle timeout Parameter minutes The timeout time ranging from 5 to 30 in minutes The value is 10 by default Command Mode Global Configuration Mode Example Configure the timeout time of the switch as 15 minutes TL SG3424 config user idle timeout 15 line Description The line command is used to enter the Line Configuration Mode and make related configuration for the desired user s including the login mode and password configurations Syntax line console inenum vty startlinenum endlinenum 56 Parameter linenum The number of users allowed to login thr
123. hNoPriv authNoPriv authPriv read read view write write view notify notify view no snmp server group name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv Parameter name The SNMP Group name ranging from 1 to 16 characters The Group Name Security Model and Security Level compose the identifier of the SNMP Group These three items of the Users in one group should be the same v1 v2c v3 Security Model with v1 v2c and v3 options They represent SNMP v1 SNMP v2c and SNMP v3 noAuthNoPriv authNoPriv authPriv The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv 232 authorization and encryption By default the Security Level is noAuthNoPriv There is no need to configure this in SNMP v1 Mode and SNMP v2c Mode read view Select the View to be the Read View The management access is restricted to read only and changes cannot be made to the assigned SNMP View write view Select the View to be the Write View The management access is writing only and changes can be made to the assigned SNMP View The View defined both as the Read View and the Write View can be read and modified notify view Select the View to be the Notify View The management station can receive notification messages of the assigned SNMP view generated b
124. hapter 16 SSL Commands 10000000 100 ip Nttp SECUFE SEIVE init e EA A NEE nent ela eee DENG 100 ip http secure server download Certificate 100 ip http secure server download key 101 show RS tnter EEEEEEEEEEEEE EEEE EEEEEE EEE EEE EEEE Eneee 102 Chapter 17 MAC Address Commandes 103 leg lee TEE e 103 mac address table aging me 104 mac address table filtering cnn nnnnnnccncnnnss 104 mac address table max mac Count ttr tnternnnereeEnnee EEn neee 105 show mac address tablei EE 106 show mac address table aging time ooooococcnnocccnnnoocccccnnoocccnonnnccnnnnnnncnnnnnnncnnnonnnnnnnncannnncnnnns 106 show mac address table max mac count interface gigabitEthernet oooonoccccnnnncccnnnncccccccnns 107 show mac address table interface oigabttihemet 107 show mac address table COUN c ccccceeeeeeeeeeeeeneeeeeeeeeeeeeecneeeeeeeeaeeeeeeseeaeeeeseeeeeeeeeeeaneeess 108 show mac address table address sssneeeskeeeesetttettn tett tterttttttttrttttrrrtntertnnerennnre rneer 108 show mac address table vlan cccccccceeeseceeeeeeneeeeeeeneeeeesecaeeeesecaeeeeseceaeeeesseeeeeeesenieeeeenes 109 Chapter 18 System Configuration Commandes 110 system tme MaMa aeaa Aa a cesar eege eg ee 110 eelere EE DEER peso peak aS eek SAN SL ee See E ten eee 110 system time dst predefned ttrt rttrEE ntet E rnEeE En En nerEn nere Eneee 112 system time dst date timida AAL EARE es ine aon EEE E 113 syst m time dst FECUIFING vaticina NEE E
125. he system will automatically release the connection if there is no operation from the client It ranges from 1 to 120 in seconds By default this value is 120 seconds Command Mode Global Configuration Mode Example Specify the idle timeout time of SSH as 100 seconds TL SG3424 config ip ssh timeout 100 ip ssh max client Description The ip ssh max client command is used to specify the maximum number of the connections to the SSH server To return to the default configuration please use no ip ssh max client command Syntax ip ssh max client num no ip ssh max client Parameter num The maximum number of the connections to the SSH server It ranges from 1 to 5 By default this value is 5 97 Command Mode Global Configuration Mode Example Specify the maximum number of the connections to the SSH server as 3 TL SG3424 config ip ssh max client 3 ip ssh download Description The ip ssh download command is used to download the SSH key file from TFTP server Syntax ip ssh download v1 v2 key file ip address p addr Parameter v1 v2 Select the type of SSH key to download v1 represents SSH 1 v2 represents SSH 2 key file The name of the key file which is selected to download The length of the name ranges from 1 to 25 characters The key length of the downloaded file must be in the range of 256 to 3072 bits ip addr The IP address of the TFTP server Both IPv4 and IPv6
126. hello 80 cluster ntdp Description The cluster ntdp command is used to configure NTDP globally To return to the default configuration please use no cluster ntdp command NTDP Neighbor Topology Discovery Protocol is used to collect the NDP information and neighboring connection information of each device in a specific network range It provides the commander switch with the information of devices which can join the cluster and collects topology information of devices within the specified hops Syntax cluster ntdp cluster ntdp timer interval time time hop delay value port delay value cluster ntdp hop hop value no cluster ntdp no cluster ntdp timer interval time time hop delay value port delay value no cluster ntdp hop hop value Parameter time NTDP Interval Time which is the interval to collect topology information NTDP Interval Time ranges from 1 to 60 in minutes By default it is 1 hop delay value NTDP Hop Delay which is the time between the switch receiving NTDP request packets and the switch forwarding NTDP request packets for the first time NTDP Hop Delay ranges from 1 to 1000 in milliseconds By default it is 200 port delay value NTDP Port Delay which is the time between the port forwarding NTDP request packets and its adjacent port forwarding NTDP 261 request packets over NTDP Port Delay ranges from 1 to 100 in milliseconds By default it is 20 hop value NTD
127. how loopback detection global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of loopback detection function TL SG3424 show loopback detection global show loopback detection interface Description The show loopback detection interface command is used to display the configuration of loopback detection function and the status of the specified Ethernet port Syntax show loopback detection interface gigabitEthernet port Parameter port The Ethernet port number 159 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of loopback detection function and the status of all ports TL SG3424 show loopback detection interface Display the configuration of loopback detection function and the status of port 5 TL SG3424 show loopback detection interface gigabitEthernet 1 0 5 160 Chapter 25 PoE Commands Mnote Only TL SG3424P supports PoE function PoE Power over Ethernet technology describes a system to transmit electrical power along with data to remote devices over standard twisted pair cable in an Ethernet network It is especially useful for supplying power to IP telephones wireless LAN access points cameras and so on power inline consumption global Description The power inline consumption command is used to configure the max power the PoE switch can supply globally Syntax power inline consu
128. hport access vlan Description The switchport access vlan command is used to add the desired Access port to IEEE 802 1Q VLAN To remove the specified port ports from the corresponding VLAN please use no switchport access vlan command Syntax switchport access vlan vian id no switchport access vlan Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 2 to 4094 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the Link Type of port 3 as access and add it to VLAN 2 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if switchport mode access TL SG3424 config if switchport access vlan 2 switchport trunk allowed vian Description The switchport trunk allowed vlan command is used to add the desired Trunk port to IEEE 802 1Q VLAN To delete the corresponding VLAN s please use no switchport trunk allowed vlan command Syntax switchport trunk allowed vlan vian list 28 no switchport trunk allowed vlan vian list Parameter vlan list Specify IEEE 802 1Q VLAN ID list ranging from 2 to 4094 in the format of 2 3 5 It is multi optional Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the Link Type of port 2 as trunk and add it to VLAN 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if switchport mode trun
129. iate leave function on VLAN 2 TL SG3424 config ipv6 mid snooping vlan 2 immediate leave ipv6 mid snooping vlan mrouter Description The ipv6 mld snooping vlan mrouter command is used to configure the static router port in a specified VLAN To disable the static router port please use no mld snooping vlan mrouter command Syntax ipv6 mld snooping vlan vian id mrouter interface gigabitEthernet port no ipv6 mid snooping vlan vian id mrouter interface gigabitEthernet port Parameter vlan id The specified IEEE 802 1Q VLAN ID ranging from 1 to 4094 port Interface number of the router port s 220 Command Mode Global Configuration Mode Example Configure the gigabitEthernet 1 0 2 as static router port in VLAN 2 TL SG3424 config ipv6 mid snooping vlan 2 mrouter interface gigabitEthernet 1 0 2 ipv6 mid snooping vlan static Description The ipv6 mld snooping vlan static command is used to configure the static multicast groups To disable the static multicast group please use no ipv6 mld snooping vlan static command Syntax ipv6 mld snooping vlan vian id static pv6_multicast_addr interface gigabitEthernet port no ipv6 mid snooping vlan vian id static pv6_multicast_addr interface gigabitEthernet port Parameter vlan id The multicast group VLAN ID ranging from 1 to 4094 ipv6_multicast_addr Pv6 address of the static multicast group port Interface number of the member p
130. ig line login Configure the login of virtual terminal connection 0 5 as login mode TL SG3424 config line vty 0 5 TL SG3424 config line login login local Description The login local command is used to configure the login of a switch with the user name and password Syntax login local Command Mode Line Configuration Mode Example Configure the login of virtual terminal connection 0 5 as login local mode TL SG3424 config line vty 0 5 TL SG3424 config line login local Configure the login of Console port connection 0 as login local mode TL SG3424 config line console 0 TL SG3424 config line login local show user account list Description The show user account list command is used to display the information of the current users Syntax show user account list Command Mode Privileged EXEC Mode and Any Configuration Mode 59 Example Display the information of the current users TL SG3424 config show user account list show user configuration Description The user configuration command is used to display the security configuration information of the users including access control max number and the idle timeout etc Syntax show user configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the security configuration information of the users TL SG3424 config show user configuration 60 Chapter 10 Binding Table Commands You can bind the IP address
131. ile Edit Yiew Call Transfer Help Dae 3 DB TL SG3424 gt enable Password TL SG3424Hconfig TL SG63424 config ip ssh download v2 public ip address 192 168 0 100 Start to download SSH key file Download SSH key file OK TL SG3424 config _ The file name of the public key The IP address of the TFTP server Connected 0 00 45 Auto detect 38400 8 N 1 Figure 1 21 Download the Public Key Anote 1 The key type should accord with the type of the key file 2 The SSH key downloading can not be interrupted 14 4 After the public key is loaded please log on to the interface of PUTTY and enter the IP address for login X PuTTY Configuration Category B Session Logging Terminal Keyboard Bell Features Window Appearance Behaviour Translation Selection Colours Connection Data Proxy Telnet Rlogin SSH Kex Auth TTY x11 ____ Basic options for your PuTTY session Specify the destination you want to connect to Host Name or IP address Port 192 168 0 1 22 Connection type ORaw O Iene O Rlogin SSH Serial Load save or delete a stored session Saved Sessions Default Settings Close window on exit Odlways O Never Only on clean exit Figure 1 22 SSH Connection Config Click Browse to load the private key file to SSH client software and click Open CG Pul TY Configuration Category Terminal Keyboard Bell Features
132. ing file flash level Description The logging file flash level command is used to specify the system log message severity level Messages will a severity level equal to or higher than this value will be stored to the flash To restore to the default level please use no logging file flash level command Syntax logging file flash level evel no logging file flash level Parameter level Severity level of the log message There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be saved to the flash By default it is 2 indicating that the log message marked with 0 2 will be saved in the log flash Command Mode Global Configuration Mode Example Save the log messages with their severities equal or higher than 7 to the flash TL SG3424 config logging file flash level 7 clear logging Description The clear logging command is used to clear the information in the log buffer and log file 91 Syntax clear logging buffer flash Parameter buffer flash The output channels buffer and flash Clear the information of the two channels by default Command Mode Global Configuration Mode Example Clear the information in the log file TL SG3424 config clear logging buffer logging host index Description The logging host index command is used to configure the Log Host To clear the configuration of th
133. ion indicates ARP detection Command Mode Global Configuration Mode 62 Example Modify the hostname as tp link of the entry with the index 1 TL SG3424 config ip source binding index 1 hostname tp link ip dhcp snooping Description The ip dhcp snooping command is used to enable DHCP Snooping function globally To disable DHCP Snooping function globally please use no ip dhcp snooping command DHCP Snooping functions to monitor the process of the Host obtaining the IP address from DHCP server and record the IP address MAC address VLAN and the connected Port number of the Host for automatic binding The switch can also propagate the control information and the network parameters via the Option 82 field to provide more information for the Host Syntax ip dhcp snooping no ip dhcp snooping Command Mode Global Configuration Mode Example Enable the DHCP Snooping function globally TL SG3424 config ip dhcp snooping ip dhcp snooping global Description The ip dhcp snooping global command is configure DHCP Snooping globally To restore to the default value please use no ip dhcp snooping global command Syntax ip dhcp snooping global global rate global rate dec threshold dec threshold dec rate dec rate no ip dhcp snooping global 63 Parameter global rate The value to specify the maximum amount of DHCP messages that can be forwarded by the switch per second The excessive messages wil
134. ion show storm control Description The show storm control command is used to display the storm control information of Ethernet ports Syntax show storm control interface gigabitEthernet port range gigabitEthernet port list y Parameter port The Ethernet port number port list The list of Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the storm control information of port 4 5 6 and 7 142 TL SG3424 config show storm control interface range gigabitEthernet 1 0 4 7 show bandwidth Description The show bandwidth command is used to display the bandwidth limit information of Ethernet ports Syntax show bandwidth interface gigabitEthernet port range gigabitEthernet port list y Parameter port The Ethernet port number port list The list of the Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the bandwidth limit information of port 4 TL SG3424 config show bandwidth interface gigabitEthernet 1 0 4 143 Chapter 21 QoS Commands QoS Quality of Service function is used to optimize the network performance lt provides you with network service experience of a better quality qos Description The qos command is used to configure CoS Class of Service based on port To return to the default configuration please use no qos command Syntax qos cos id no qos Parameter cos
135. ion through an Ethernet port 1 1 1 Logon by a console port To log on to the switch by the console port on the switch please take the following steps 1 Connect the PCs or Terminals to the console port on the switch by a provided cable 2 Click Start All Programs gt Accessories Communications Hyper Terminal to open the Hyper Terminal as the Figure 1 1 shown Set Program Access and Defaults W Windows Catalog Windows Update D Program Updates Accessibility ei Games H Startup 8 Internet Explorer ei Entertainment e Network Connections ei System Tools e vv KA e Internet Internet Explorer 9 Network Setup Wizard SS Ww MN 3J Address Book E New Connection Wizard ES Microsc fice Out E Outlook Express 3 Calculator Remote Desktop Connection w i Remote Assistance E Command Prompt Wireless Network Setup Wizard e Notepad windows Media Player E Notepad 3 Windows Messenger Y Paint ES Command Prompt a Windows Movie Maker S i Program Compatibility Wizard A Activate Windows EA Synchronize OvisLink Wireless Che Utility 9 MSN EH IxChariot EH asmax E LogMeTT Tera Term E Microsoft Office Windows Media Play Im Macrovision Y Paint E TP LINK All Programs ei OvisLink Divo ug oi sn OFF Computer Tour Windows XP Windows Explorer A WordPad ae me e e me e me me Fig
136. iption The ip dhcp snooping information strategy command is used to select the operation for the Option 82 field of the DHCP request packets from the Host To restore to the default option please use no ip dhcp snooping information strategy command Syntax ip dhcp snooping information strategy strategy no ip dhcp snooping information strategy Parameter strategy The operations for Option 82 field of the DHCP request packets from the Host including three types keep Indicates to keep the Option 82 field of the packets It is the default option replace Indicates to replace the Option 82 field of the packets with the switch defined one drop Indicates to discard the packets including the Option 82 field Command Mode Global Configuration Mode Example Replace the Option 82 field of the packets with the switch defined one and then send out TL SG3424 config ip dhcp snooping information strategy replace ip dhcp snooping information remote id Description The ip dhcp snooping information remote id command is used to enable and configure the customized sub option Remote ID for the Option 82 To return to default Remote ID for the Option 82 please use no ip dhcp snooping information remote id command 65 Syntax ip dhcp snooping information remote id string no ip dhcp snooping information remote id Parameter string Enter the sub option Remote ID which contains 32 characters at most Comma
137. irst Follow the steps in 1 1 1 Logon by a console port to log on to the switch and then follow the steps shown in Figure 1 6 to configure the Privileged EXEC Mode password TPLINK HyperTerminal File Edit View Call Transfer Help TL SG3424 gt enable TL SG3424tconfig TL S63424 config enable password 123 lt entering Privileged set password for EXEC Mode TL SG3424 config H Figure 1 6 Configure the Privileged EXEC Mode Password 1 1 3 Logon by Telnet To successfully create Telnet connection firstly CLI commands about configuring Telnet login mode login authentication information and Privileged EXEC Mode password should be configured through Console connection Telnet login has the following two modes you can choose one according to your needs Login local Mode It requires username and password which are both admin by default Login Mode It requires no username and password but a connection password is required Note Before Telnet login you are required to configure Telnet login mode and login authentication information through console connection gt Login Local Mode Firstly enter the Privileged EXEC Mode password set in 1 1 2 Configuring the Priviledged EXEC Mode Password and configure the Telnet login mode as login local in the prompted DOS screen shown in Figure 1 7 TPLINK HyperTerminal DDR File Edit View Call Transfer Help DS ZS D286 YE TL SG3424b gt enable Passuord 4 TL S
138. ity as 4096 TL SG3424 config spanning tree priority 4096 193 spanning tree tc defend Description The spanning tree tc defend command is used to configure the TC Protect of Spanning Tree globally To return to the default configuration please use no spanning tree tc defend command A switch removes MAC address entries upon receiving TC BPDUs If a malicious user continuously sends TC BPDUs to a switch the switch will be busy with removing MAC address entries which may decrease the performance and stability of the network Syntax spanning tree tc defend threshold threshold period period no spanning tree tc defend Parameter threshold TC Threshold ranging from 1 to 100 packets By default it is 20 TC Threshold is the maximum number of the TC BPDUs received by the switch in a TC Protect Cycle period TC Protect Cycle ranging from 1 to 10 in seconds By default it is 5 Command Mode Global Configuration Mode Example Configure TC Threshold as 30 packets and TC Protect Cycle as 10 seconds TL SG3424 config spanning tree tc defend threshold 30 period 10 spanning tree timer Description The spanning tree timer command is used to configure forward time hello time and max age of Spanning Tree To return to the default configurations please use no spanning tree timer command Syntax spanning tree timer forward time forward time hello time hello time max age max age no spanning tree timer
139. k TL SG3424 config if switchport trunk allowed vlan 2 switchport general allowed vlan Description The switchport general allowed vlan command is used to add the desired General port to IEEE 802 1Q VLAN and specify the egress rule To delete the corresponding VLAN s please use no switchport general allowed vlan command Syntax switchport general allowed vlan vian list tagged untagged no switchport general allowed vlan vian list Parameter vlan list Specify IEEE 802 1Q VLAN ID list ranging from 2 to 4094 in the format of 2 3 5 It is multi optional tagged untagged Egress rule untagged or tagged Tagged All packets forwarded by the port are tagged The packets contain VLAN information Untagged Packets forwarded by the port are untagged Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the Link Type of port 4 as general then add it to VLAN 2 and configure the egress rule of port 4 as tagged TL SG3424 config interface gigabitEthernet 1 0 4 TL SG3424 config if switchport mode general 29 TL SG3424 config if switchport general allowed vlan 2 tagged switchport pvid Description The switchport pvid command is used to configure the PVID for the switch ports Syntax switchport pvid vian id Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 Command Mode Interface Configuratio
140. l be discarded The options are 0 10 20 30 40 50 packet second By default it is O standing for disable dec threshold The value to specify the minimum transmission rate of the Decline packets to trigger the Decline protection for the specific port The options are 0 5 10 15 20 25 30 packet second By default it is O standing for disable dec rate The value to specify the Decline Flow Control The traffic flow of the corresponding port will be limited to be this value if the transmission rate of the Decline packets exceeds the Decline Threshold The options are 5 10 15 20 25 30 packet second By default it is 5 Command Mode Global Configuration Mode Example Configure the Global Flow Control as 30pps the Decline Threshold as 20 pps and decline Flow Control as 20 pps for DHCP Snooping TL SG3424 config ip dhcp snooping global global rate 30 dec threshold 20 dec rate 20 ip dhcp snooping information option Description The ip dhcp snooping information option command is used to enable the Option 82 function of DHCP Snooping To disable the Option 82 function please use no ip dhcp snooping information option command Syntax ip dhcp snooping information option no ip dhcp snooping information option Command Mode Global Configuration Mode Example Enable the Option 82 function of DHCP Snooping 64 TL SG3424 config ip dhcp snooping information option ip dhcp snooping information strategy Descr
141. le rule id deny permit sip source ip smask source ip mask dip destination ip dmask destination ip mask tseg time segment no access list standard aci id rule rule id Parameter acl id The desired Standard IP ACL for configuration rule id The rule ID deny The operation to discard packets permit The operation to forward packets It is the default value source ip The source IP address contained in the rule source ip mask The source IP address mask It is required if you typed the source IP address destination ip The destination IP address contained in the rule destination ip mask The destination IP address mask It is required if you typed the destination IP address time segment The time range for the rule to take effect By default it is not limited Command Mode Global Configuration Mode Example Create a Standard IP ACL whose ID is 120 and add Rule 10 for it In the rule the source IP address is 192 168 0 100 the source IP address mask is 176 255 255 255 0 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TL SG3424 config access list create 120 TL SG3424 config access list standard 120 rule 10 permit sip 192 168 0 100 smask 255 255 255 0 tseg tSeg1 access list extended Description The access list extended command is used to add Extended IP ACL rule To
142. learned on the port The port with Port Security feature enabled will learned the MAC address dynamically When the learned MAC address number reaches the maximum the port will stop learning Therefore the other devices with the MAC address unlearned cannot access to the network via this port Syntax mac address table max mac count max number num mode dynamic static permanent status disable enable no mac address table max mac count Parameter num The maximum number of MAC addresses that can be learned on the port It ranges from 0 to 64 By default this value is 64 dynamic static permanent Learn mode for MAC addresses There are three modes including Dynamic mode Static mode and Permanent mode When Dynamic mode is selected the learned MAC address will be deleted automatically after the aging time When Static mode is selected the learned MAC address will be out of the influence of the aging time and can only be deleted manually The learned entries will be cleared after the switch is rebooted When permanent mode is selected the learned MAC address will be out of the influence of the aging time and can only be deleted manually too However the learned entries will be saved even the switch is rebooted status Enable or disable the Port Security function for a specified port By default this function is disabled 105 Command Mode Interface Configuration Mode interface giga
143. lert When a loop is detected display an alert Port based When a loop is detected display an alert and block the port auto manual The mode how the blocked port recovers to normal status Auto Block status can be automatically removed after recovery time Manual Block status can only be removed manually Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the loopback detection process mode as port based and recovery mode as manual for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if loopback detection config process mode port based recovery mode manual loopback detection recover Description The loopback detection recover command is used to remove the block status of selected ports thus recovering the blocked ports to normal status 158 Syntax loopback detection recover Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Recover the blocked port 2 to normal status TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if loopback detection recover show loopback detection global Description The show loopback detection global command is used to display the global configuration of loopback detection function such as loopback detection global status loopback detection interval and loopback detection recovery time Syntax s
144. ly recover to normal status Syntax loopback detection recovery time recovery time Parameter recovery time The time after which the blocked port would automatically recover to normal status and the loopback detection would restart It is integral times of detection interval ranging from 1 to 100 and the default value is 3 Command Mode Global Configuration Mode Example Configure the recovery time as 3 times of detection interval TL SG3424 config loopback detection recovery time 3 loopback detection interface Description The loopback detection command is used to enable the loopback detection function of the specified port To disable it please use no loopback detection command Syntax loopback detection no loopback detection Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the loopback detection function of ports 1 3 157 TL SG3424 config interface range gigabitEthernet 1 0 1 3 TL SG3424 config if range loopback detection loopback detection config Description The loopback detection config command is used to configure the process mode and recovery mode for the ports by which the switch copes with the detected loops Syntax loopback detection config process mode alert port based recovery mode auto manual Parameter alert port based The mode how the switch processes the detected loops A
145. mand is used to display the LLDP and LLDP MED neighbor information of the corresponding port By default the neighbor information of all the ports will be displayed Syntax show Ildp neighbor information interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP and LLDP MED neighbor information of port 1 TL SG3424P show lldp neighbor information interface gigabitEthernet 1 0 1 258 show Ildp traffic interface Description The show Ildp traffic interface command is used to display the LLDP statistic information between the local device and neighbor device of the corresponding port By default the LLDP statistic information of all the ports will be displayed Syntax show Ildp traffic interface gigabitEthernet port Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP statistic information of port 1 TL SG3424P show Ildp traffic interface gigabitEthernet 1 0 1 259 Chapter 32 Cluster Commands Cluster Management function enables a network administrator to manage the scattered devices in the network via a management device After a commander switch is configured management and maintenance operations intended for the member devices in a cluster is implemented by the commander device cluster ndp Descrip
146. me supply enable disable priority low middle high consumption power limit auto class1 class2 class3 class4 no power profile name Parameter name The PoE profile name ranging from 1 to 16 characters If the name being assigned contains spaces then put it inside double quotes supply The PoE status of the port in the profile By default the PoE status is enable priority The PoE priority of the port in the profile The priority levels include high middle and low in descending order When the supply power exceeds the system power limit the PD linked to the port with lower priority will be disconnected By default the PoE priority is low consumption The max power the port in the profile can supply with five options power limit auto class1 class2 class3 and class4 Power limit indicates you can manually enter a value ranging from 1 to 300 The value is in the unit of 0 1 watt For instance if you want to configure the max power as 5w you should enter 50 Auto indicates the value is assigned automatically by the PoE switch Class1 represents 4w Class2 represents 7w Class3 represents 15 4w Class4 represents 30w 162 Command Mode Global Configuration Mode Example Create a PoE profile named IP Camera whose PoE status is enable PoE priority is low and the
147. mer is set the port with GVRP enabled can send a LeaveAll message after the timer times out so that other GARP ports can re register all the attribute information After that the LeaveAll timer will start to begin a new cycle To guarantee the transmission of the Join messages a GARP port sends each Join message two times The Join Timer is used to define the interval between the two sending operations of each Join message Once the Leave Timer is set the GARP port receiving a Leave message will start its Leave timer and deregister the attribute information if it does not receive a Join message again before the timer times out value The value of the timer The LeaveAll Timer ranges from 1000 to 30000 centiseconds and the default value is 1000 The Join Timer ranges from 20 to 1000 centiseconds and the default value is 20 The Leave Timer ranges from 60 to 3000 centiseconds and the default value is 60 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Set the GARP leaveall timer of port 6 to 2000 centiseconds and restore to the join timer of it to the default value TL SG3424 config interface gigabitEthernet 1 0 6 TL SG3424 config if gvrp timer leaveall 2000 TL SG3424 config if no gvrp timer join show gvrp global Description The show gvrp global command is used to display the global GVRP status Syntax show gvrp global Command Mode Privileged
148. mption power limit Parameter power limit The max power the PoE switch can supply ranging from 1 to 320w By default the value is 320 Command Mode Global Configuration Mode Example Configure the max power the PoE switch can supply as 160w TL SG3424P config power inline consumption 160 power inline disconnect method Description The power inline disconnect method command is used to offset the power limit being exceeded and keep the switch system using power at a usable level Syntax power inline disconnect method deny next port deny low priority Parameter deny next port When the supply power exceeds the power limit the PD linked to the next port will be disconnected 161 deny low priority When the supply power exceeds the power limit the PD linked to the port with lower priority will be disconnected Command Mode Global Configuration Mode Example Configure the power disconnect method as deny next port TL SG3424P config power inline disconnect method deny next port power profile Description The power profile command is used to create a PoE profile for the switch To delete the configured PoE profile configuration please use no power profile command PoE Profile is a short cut for the configuration of the PoE port In a PoE profile the PoE status PoE priority and power limit are configured You can specify a POE profile for each PoE port individually Syntax power profile na
149. n To clear the system location information please use no location command Syntax location ocation no location Parameter location Device Location It consists of 32 characters at most It is SHENZHEN by default Command Mode Global Configuration Mode Example Configure the system location as SHENZHEN TL SG3424 config location SHENSHEN 115 contact info Description The contact info command is used to configure the system contact information To clear the system contact information please use no contact info command Syntax contact info contact_info no contact info Parameter contact_info Contact Information It consists of 32 characters at most It is www tp link com by default Command Mode Global Configuration Mode Example Configure the system contact information as www tp link com TL SG3424 config contact info www tp link com ip management vlan Description The ip management vlan command is used to configure the management VLAN through which you can log on to the switch By default the management VLAN is VLAN1 Syntax ip management vlan vlan id Parameter vlan id VLAN ID ranging from 1 to 4094 Command Mode Global Configuration Mode Example Set the VLAN6 as management VLAN TL SG3424 config ip management vlan 6 116 ip address Description The ip address command is used to configure the system IP Address Subnet Mask and Default Gat
150. n Mode interface gigabitEthernet interface range gigabitEthernet Example Specify the PVID of port 3 as 1 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if switchport pvid 1 show vlan summary Description The show vlan summary command is used to display the summarized information of IEEE 802 1Q VLAN Syntax show vlan summary Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the summarized information of IEEE 802 1Q VLAN TL SG3424 config show vlan summary 30 show vlan brief Description The show vlan brief command is used to display the brief information of IEEE 802 1Q VLAN Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the brief information of IEEE 802 1Q VLAN TL SG3424 config show vlan brief show vlan Description The show vlan command is used to display the detailed information of the specified IEEE 802 1Q VLAN Syntax show vlan id vian list Parameter vlan list Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 It is multi optional By default the detailed information of all VLANs will be displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the detailed information of all VLANs TL SG3424 config show vian Display the detailed information of VLAN 2 TL SG3424 config show vlan id 2 Display the detailed information of VLAN 3
151. nable the IEEE 802 1X function for port 1 TL SG3424 config interface gigabitEthernet 1 0 1 TL SG3424 config if dot1x dot1x guest vlan interface Description The dot1x guest vlan command is used to enable the guest VLAN function for a specified port To disable the Guest VLAN function for a specified port please use no dot1x guest vlan command Please ensure that the Control Type of the corresponding port is port based before enabling the guest VLAN function for it Syntax dot1x guest vlan no dot1x guest vlan Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the Guest VLAN function for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if dot1x guest vlan dot1x port control Description The dot1x port control command is used to configure the control mode of IEEE 802 1X for the specified port By default the control mode is auto To restore to the default configuration please use no dot1x port control command 83 Syntax dot1x port control auto authorized force unauthorized force no dot1x port control Parameter auto authorized force unauthorized force The Control Mode for the port auto In this mode the port will normally work only after passing the 802 1X Authentication authorized force In this mode the port can work normally without passing the 802 1X Authentication un
152. named policy1 179 TL SG3424 config access list policy name policy1 access list policy action Description The access list policy action command is used to add ACLs and create actions for the policy To set the detailed configuration of actions for a policy please use access list policy action command to access Action Configuration Mode To delete the corresponding actions please use no access list policy action command Syntax access list policy action policy name acl id no access list policy action policy name acl id Parameter policy name The Policy Name ranging from 1 to 16 characters acl id The ID of the ACL to which the above policy is applied Command Mode Global Configuration Mode Example Add ACL whose ID is 120 to policy1 and create an action for them TL SG3424 config access list policy action policy1 120 redirect interface Description The redirect interface command is used to configure Direction function of policy action for specified ports Syntax redirect interface gigabitEthernet port Parameter port The destination port number of redirect Command Mode Action Configuration Mode 180 Example Edit the actions for policy1 Forward the data packets matching ACL 120 in the policy to port 2 TL SG3424 config access list policy action policy1 120 TL SG3424 config action redirect interface gigabitEthernet 1 0 2 redirect vlan Description The redirect vlan comman
153. nd Mode Global Configuration Mode Example Enable and configure the customized sub option Remote ID for the Option 82 as tplink TL SG3424 config ip dhcp snooping information remote id tplink ip dhcp snooping information circuit id Description The ip dhcp snooping information circuit id command is used to enable and configure the customized sub option Circuit ID for the Option 82 To return to the default Circuit ID for the Option 82 please use no ip dhcp snooping information circuit id command Syntax ip dhcp snooping information circuit id string no ip dhcp snooping information circuit id Parameter string Enter the sub option Circuit ID which contains 32 characters at most Command Mode Global Configuration Mode Example Enable and configure the customized sub option Circuit ID for the Option 82 as tplink TL SG3424 config ip dhcp snooping information circuit id tplink 66 ip dhcp snooping trust Description The ip dhcp snooping trust command is used to configure a port to be a Trusted Port Only the Trusted Port can receive the DHCP packets from DHCP servers To turn the port back to a distrusted port please use no ip dhcp snooping trust command Syntax ip dhcp snooping trust no ip dhcp snooping trust Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure port 2 to be a Trusted Port TL SG3424 config interface gigabi
154. nd attack scan synfin Scan SYNFIN attack xma scan Xma Scan attack null scan NULL Scan attack port less 1024 The SYN packets whose Source Port less than 1024 blat Blat attack ping flood Ping flooding attack With the ping flood attack enabled the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by ping flood syn flood SYN SYN ACK flooding attack With the syn flood attack enabled the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by syn flood Command Mode Global Configuration Mode Example Enable the DoS Defend Type named Land attack TL SG3424 config ip dos prevent type land show ip dos prevent Description The show ip dos prevent command is used to display the DoS information of the detected DoS attack including enable disable status the DoS Defend Type Syntax show ip dos prevent Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the DoS information of the detected DoS attack globally TL SG3424 config show ip dos prevent 78 Chapter 13 IEEE 802 1X Commands IEEE 802 1X function is to provide an access control for LAN ports via the authentication Only the supplicant passing the authentication can access the LAN dot1x system auth control Description The dot1x system auth control command is used to enable the IEEE 802 1X function glob
155. nd is used to configure the Location Identification TLV s content in outgoing LLDPDU of the port Syntax lldp med location emergency number identifier civic address language language province state province state county county city city street street house number house number name name postal zipcode postal zipcode room number room number post office box post office box additional additional country code country code what dhcp server endpoint switch Parameter emergency number Emergency Call Service ELIN identifier which is used during emergency call setup to a traditional CAMA or ISDN trunk based PSAP The length of this field ranges from 10 to 25 characters civic address The civic address is defined to reuse the relevant sub fields of the DHCP option for civic Address based Location Configuration Information as specified by IETF Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the civic address in the Location Identification TLV s content in outgoing LLDPDU of port 2 Configure the language as English and city as London TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if Ildp med location civic address language English city London Ildp med status Description The lldp med status command is used to enable the LLDP MED feature for the correspondi
156. nds and the retries time as 100 TL SG3424 config snmp server host fe80 1234 162 admin smode v2c type inform retries 100 timeout 1000 snmp server enginelD Description Syntax The snmp server enginelD command is used to configure the local and remote enginelD of the switch To restore to the default setting please use no snmp server enginelD command snmp server enginelD local ocal enginelD remote remote enginelD no snmp server enginelD Parameter local enginelD Local Engine ID for local clients The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the switch Its length ranges from 10 to 64 hexadecimal characters which must be even number meanwhile remote enginelD Remote Engine ID for the switch The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the remote device which receives informs from the switch lts length ranges from 10 to 64 hexadecimal characters which must be even number meanwhile The snmp server enginelD will be disabled if the local and remote are both not configured Command Mode Global Configuration Mode Example Specify the local enginelD as 1234567890 and the remote enginelD as abcdef123456 TL SG3424 config snmp server enginelD local 1234567890 remote abcdef123456 237 snmp server traps snmp Description Syntax The snmp server traps snmp command is used to enable SNMP standard trap
157. net command is used to enter the interface range gigabitEthernet Configuration Mode and configure multiple Gigabit Ethernet ports at the same time Syntax interface range gigabitEthernet port list Parameter port list The list of Ethernet ports Command Mode Global Configuration Mode 132 User Guidelines Command in the Interface Range gigabitEthernet Mode is executed independently on all ports in the range It does not affect the execution on the other ports at all if the command results in an error on one port Example To enter the Interface range gigabitEthernet Configuration Mode and configure ports 1 2 3 6 7 and 9 at the same time by adding them to one port list TL SG3424 config interface range gigabitEthernet 1 0 1 3 1 0 6 7 1 0 9 description Description The description command is used to add a description to the Ethernet port To clear the description of the corresponding port please use no description command Syntax description string no description Parameter string Content of a port description ranging from 1 to 16 characters Command Mode Interface Configuration Mode interface gigabitEthernet Example Add a description Port 5 to port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if description Port 5 shutdown Description The shutdown command is used to disable an Ethernet port To enable this port again please use no shutdown command Synta
158. nfiguration file named as config cfg to the switch from TFTP server with the IP fe80 1234 TL SG3424 copy tftp startup config ip address fe80 1234 filename config firmware upgrade ping Description The firmware upgrade command is used to upgrade the switch system file via the TFTP server Syntax firmware upgrade ip address p addr filename name Parameter ip addr IP Address of the TFTP server Both IPv4 and IPv6 addresses are supported for example 192 168 0 1 or fe80 1234 name Specify the name for the firmware file Command Mode Privileged EXEC Mode Example Upgrade the switch system file named as firmware bin via the TFTP server with the IP address 192 168 0 148 TL SG3424 firmware upgrade ip address 192 168 0 148 filename firmware bin Upgrade the switch system file named as firmware bin via the TFTP server with the IP address fe80 1234 TL SG3424 firmware upgrade ip address fe80 1234 filename firmware bin Description The ping command is used to test the connectivity between the switch and one node of the network 121 Syntax ping ip ipv6 jo_addr n count I count i count Parameter ip The type of the IP address for ping test should be IPv4 ipv6 The type of the IP address for ping test should be IPv6 ip_addr The IP address of the destination node for ping test If the parameter ip ipv6 is not selected both IPv4 and IPv6 addresses are supported for e
159. nfigure its mode To delete the port from the EtherChannel Group please use no channel group command Syntax channel group num mode on active passive no channel group Parameter num The number of the EtherChannel Group ranging from 1 to 8 on Enable the static LAG active Enable the active LACP mode passive Enable the passive LACP mode Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Add ports 2 4 to EtherChannel Group 1 and enable the static LAG TL SG3424 config interface range gigabitEthernet 1 0 2 4 TL SG3424 config if range channel group 1 mode on 46 port channel load balance Description The port channel load balance command is used to configure the Aggregate Arithmetic for LAG To return to the default configurations please use no port channel load balance command Syntax port channel load balance src dst mac src dst ip no port channel load balance Parameter src dst mac The source and destination MAC address When this option is selected the Aggregate Arithmetic will be based on the source and destination MAC addresses of the packets The Aggregate Arithmetic for LAG is src dst mac by default src dstip The source and destination IP address When this option is selected the Aggregate Arithmetic will be based on the source and destination IP addresses of the packets Command Mo
160. ng port After the LLDP MED feature is enabled the port s Admin 255 Status will be changed to Tx amp Rx To disable the LLDP MED feature for the corresponding port please use no lldp med status command Syntax lldp med status no lldp med status Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the LLDP MED feature for port 2 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if lldp med status Ildp med tlv select Description The lldp med tlv select command is used to configure LLDP MED TLVs to be included in outgoing LLDPDU for the corresponding port To exclude LLDP MED TLVs please use no lldp med tlv select command By default All TLVs are included in outgoing LLDPDU Syntax lldp med tlv select inventory management location network policy power management all no lldp med tlv select inventory management location network policy power management all Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Exclude network policy and inventory TLVs in LLDPDU outgoing from port 2 TL SG3424P config interface gigabitEthernet 1 0 2 TL SG3424P config if no Ildp med tlv select network policy inventory management 256 show Ildp Description The show Ildp command is used to display the global configuration of LLDP an
161. nnected to this port will be chosen as the root port In the same condition the port with the highest priority will be chosen as the root port The lower value has the higher priority ext cost External Path Cost which is used to choose the path and calculate the path costs of ports in different MST regions It is an important criterion on determining the root port The lower value has the higher priority It ranges from o to 2000000 By default it is O which is mean auto int cost Internal Path Cost which is used to choose the path and calculate the path costs of ports in an MST region It is an important criterion on determining the root port The lower value has the higher priority By default it is automatic It ranges from o to 2000000 By default it is O which is mean auto enable disable Enable Disable Edge Port By default it is disabled The edge port can transit its state from blocking to forwarding rapidly without waiting for forward delay auto open close The P2P link status with auto open and close options By default the option is auto If the two ports in the P2P link are root port or designated port they can transit their states to forwarding rapidly to reduce the unnecessary forward delay 188 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the STP function of port 1 and configure the Port Priority as 6
162. nnnncnncnnnnnno 217 ipv6 mld snooping multicast vlan conan nnnnnonnn cnn conan ncncnncnnnss 217 ipv6 mld snooping multicast vlan van 218 ipv6 mld snooping van 218 ipv6 mld snooping vlan router a0oing me cnn nnnnnncc conan 219 xI ipv6 mld snooping vlan member aging time ssssseeeeteeeeettteettttettrrtetrrnterrnterrrnnerrrrn reren 219 ipv6 mld snooping vlan Immedlate Jeave eeren 220 ipv6 mid snooping van mrouter ccc ccececsceeeeeeeeeeeeeeeeeeeeeeeneeeeeeeaeeeeseeaeeeeseeeeeeeeteeaeaneeeeseas 220 ipv6 mld snooping WE LEE LEE 221 ipv6 mid snooping qUErIER VIAN Veinticinco ee 221 ipv6 mld snooping querier vlan Max reSPONSE tiIME ooooccccccnoccccccnoocccconnnccnnonnnncnnnnnnnconcnnnnnno 222 ipv6 mld snooping querier vlan ouerm Jntenal 223 ipv6 mld snooping querier vlan qUery SOUrCe ssssssseeeeseekttsettttettrnttrrntetttrntrrernnrenrn eeren 223 ipv6 mld snooping filter global c cccceceeceeeeeeeeeeeeneeeeeeeeeeeeeeceeeeeeseceeeeeeseeeseeeesseieeeseeees 224 ipv6 mld snooping filter interface ooooconnncccdininiccccnnonccccononancnnnnnnncnnnnnnn cnn nnnnnnnncnncnnnncnncnnnos 224 ipv6 mid snooping ter mode te tetetnteennneennnneeen erene 225 Ipv6 mid snooping filter id sss aes ease eesti sit dn a kn ieee 225 ipv6 mld snooping max OrOunD ttnt EEESEEEEEEEEEEEEEEEEAEE EEEE En renne eenen 226 clear ipv6 mld snooping statistics oooooooccnnicicinnoccconnonccnconnnancnnnnnrccnnonnn cnn nn nnnnn cnn nnonnnc
163. nnnnnnes 226 Show PVO MIA SHOOPING Wed ie 227 Show ipv6 mld SNOOPING van 227 show ipv6 mld snooping Static MCAST oooooccccnoccccconoocccccnnoncnncnnnnnnnnnnnnnnnnnonnnnnncnnnnnnnnnnannnncnnnns 228 show ipv6 Mid SNOOPING group seee e en ia aeaa aa a aat aana aandaa 228 show ipv6 mld snooping Hirer 228 show ipv6 mld snooping Interface 229 show ipv6 mld snooping interface fier 229 show ipv6 mld snooping querier ss ssssskeesstrtestitttettttetttttttttttttttrnt nert rrnnertn terenne e nnee 230 show ipv6 mld snooping statlsitce 230 Chapter 30 SNMP Commands ci ta 231 Dill e EEN Nuel 231 Gill Eege re e EE 232 A sisetetr ase a a Dae Rat tal Ra Dal Se eat Merete tay 233 SNMP SErver COmmUnlf tnter EEtSEEEEEAEEEEEEEEEEEROEEEERSEEEEEEESEEEEEnE EEEE 235 TA EAE La uri EE Eeer E EE EEE E ET 235 snmp server nee ER EEN 237 SNMP Server traps SNMP iii acaba 238 snmp server traps liNk Status cccceeeeceeeeeeeeeeceeaeeeeeeeeeeeeseseeeeeseeaeeeeseeeeeeeseeeeeeeseeeneeeees 238 SMIMPsSORVEMr TDS urticaria 239 snmp server traps MAC ENNEN 240 nl ENEE 241 o TT 241 XII MAA Rn a a AS 242 le e 243 SHOW SNMP SETVO es ss 2 ea eee ae eRe ii enadeae 245 Glenn 245 showW SshAMP SErVer QrOUP iseiti diia 245 A e ie A 246 SHOW SNMP SErver Commun 246 SHOW snmp server bost terenn tnr E Enrere 247 show snmp server enginel A 247 SNOW TMO DISTO Y EE 247 A EE 248 Stewart eer E 248 Chapter 31 LLDP Commands 000 Ee 250 ele A AAA AAA 250 d
164. nnnnnnnnnnnnnn cnn nn niannncincnnnss 205 ip igmp snooping multi vlan config ooooccnnnncccccnonoccccnononccncnnanccnnonnnnnonnnnnnnnnnnnnn cnn nnnnnncncnncnnnos 206 ip igmp snooping filter ad 207 ip igmp snooping Dliertglobal A 208 ip igmp snooping filter interface oonoooocnnnicccinnoccccnnoncccnononancnnonnnncononnnnnonnonnn cnn no nnnnnncnnnnnnss 208 ip igmp snooping filter MaXgroup cnn nonnn cnn ninnannncnncnnnss 209 ip igmp snooping filter mode ooooococconnoccccnccoccccconanccononnnncononnnnncnnonnnnnnnnnnnnnnncnnnnnnn nn ninnnncnncnnnss 209 NA le elle EE 210 show ip igmp snooping Interface 210 SHOW IP IGMP ele ele EE IEN 211 show ip igMp snooping multi vlan sssssessneeseeereeeserttetrntettttetttrtttttrntttrtntstrtnttrrt tennere rn neren 212 show ip igmp SNOOPING Oroupe 212 show ip igmp snooping Hlter cnn nannnncnnnns 213 Chapter 29 MLD Snooping Commands ooooonccccnncncccnonnnonnnnnnnnnnnnnnnnnnnnnncnnnnnnnnnnnnnns 214 TA NATA 214 ipv6 mld snooping router aging tiMe oooocinncccc nnnocccnnooocccccononccnnonancnonnnnn cnn nonnn cnn ncnnn rca cnn 214 ipv6 mid snooping member a0oing me 215 ipv6 mid Snooping report Suppression 215 ipv6 mid Snooping UNkNOWN filter oooooconnncccccnnooccccconncccncnnnancncnnnnncncnnnnn cnn nonnn cnn nnnnnncnncncnnnes 216 ipv6 mld snooping last listener ouerv Jnteval 216 ipv6 mld snooping last listener QUery COUN c ooococococccccocaccccconancnnonnnnconnnnnn cnn conan cnn nn
165. no spanning tree command Syntax spanning tree no spanning tree Command Mode Global Configuration Mode Example Enable the STP function TL SG3424 config spanning tree spanning tree interface Description The spanning tree command is used to enable STP function for a port To disable the STP function please use no spanning tree command Syntax spanning tree no spanning tree Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the STP function for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 187 TL SG3424 config if spanning tree spanning tree common config Description The spanning tree common config command is used to configure the parameters of the ports for comparison in the CIST and the common parameters of all instances To return to the default configuration please use no spanning tree common config command CIST Common and Internal Spanning Tree is the spanning tree in a switched network connecting all devices in the network Syntax spanning tree common config port priority pri ext cost ext cost int cost int cost portfast enable disable point to point auto open close no spanning tree common config Parameter pri Port Priority which must be multiple of 16 ranging from O to 240 By default the port priority is 128 Port Priority is an important criterion on determining if the port co
166. ny Configuration Mode Parameter mac addr MAC address in the format of XX XX XX XX XX XX vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 Example Display the MAC based VLAN table TL SG3424 config show mac vlan all Display the MAC based VLAN information of the entry whose MAC address is 00 11 11 01 01 12 TL SG3424 config show mac vlan mac address 00 11 11 01 01 12 Display the MAC based VLAN information of the entry whose VLAN ID is 4 TL SG3424 config show mac vlan vlan 4 33 Chapter 5 Protocol based VLAN Commands Protocol based VLAN Virtual Local Area Network is the way to classify VLANs based on Protocols A Protocol corresponds to a VLAN ID The untagged packets and the priority tagged packets matching the protocol template will be tagged with this VLAN ID protocol vlan template Description The protocol vlan template command is used to create Protocol based VLAN template To delete Protocol based VLAN template please use no protocol vlan template command Syntax protocol vlan template name protocol name ether type type frame 802_3 ether_2 snap IIc no protocol vlan template template idx Parameter protocol name Give a name to the Protocol based VLAN Template which contains 8 characters at most type The Ethernet protocol type in the protocol template composed of 4 Hex integers 802 _3 ether_2 snap llc The frame type with 802_3 ether_2
167. oice vlan priority pri no voice vlan priority Parameter pri Priority ranging from 0 to 7 Command Mode Global Configuration Mode Example Configure the priority of the Voice VLAN as 5 TL SG3424 config voice vlan priority 5 voice vlan mac address Description The voice vlan mac address command is used to create Voice VLAN OUI To delete the specified Voice VLAN OUI please use no voice vlan mac address command 38 Syntax voice vlan mac address mac addr mask mask description descript no voice vlan mac address mac addr Parameter mac addr The OUI address of the voice device in the format of AN NN NN NN NN NN mask The OUI address mask of the voice device in the format of XX XX XX XX XX XX descript Give a description to the OUI for identification which contains 16 characters at most Command Mode Global Configuration Mode Example Create a Voice VLAN OUI described as TP Phone with the OUI address 00 11 11 11 11 11 and the mask address FF FF FF 00 00 00 TL SG3424 config voice vlan mac address 00 11 11 11 11 11 mask FF FF FF 00 00 00 description TP Phone switchport voice vlan mode Description The switchport voice vlan mode command is used to configure the Voice VLAN mode for the Ethernet port Syntax switchport voice vlan mode manual auto Parameter manual auto Port mode Command Mode Interface Configuration Mode interface gigabitEthernet interf
168. on enabled the root bridge will set itself automatically as ERROR PORT when receiving BPDU packets with higher priority in order to maintain the role of root ridge To disable the Root Protect function please use no spanning tree guard root command spanning tree guard root no spanning tree guard root Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the Root Protect function for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if spanning tree guard root spanning tree guard tc Description The spanning tree guard tc command is used to enable the TC Protect of Spanning Tree function for a port To disable the TC Protect of Spanning Tree function please use no spanning tree guard tc command A switch removes MAC address entries upon receiving TC BPDUs If a malicious user continuously sends TC BPDUs to a switch the switch will be busy with removing MAC address entries which may decrease the performance and stability of the network With the Protect of Spanning Tree function enabled you can configure the number of TC BPDUs in a required time so as to avoid the process of removing MAC addresses frequently 198 Syntax spanning tree guard tc no spanning tree guard tc Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the TC Protect of Spanning T
169. onfiguring the Port Isolation function Chapter 24 Loopback Detection Commands Provide information about the commands used for configuring the Loopback Detection function Chapter 25 PoE Commands Provide information about the commands used for configuring PoE function Chapter 26 ACL Commands Provide information about the commands used for configuring the ACL Access Control List Chapter 27 MSTP Commands Provide information about the commands used for configuring the MSTP Multiple Spanning Tree Protocol Chapter 28 IGMP Snooping Commands Provide information about the commands used for configuring the IGMP Snooping Internet Group Management Protocol Snooping Chapter 29 MLD Snooping Commands Provide information about the commands used for configuring the MLD Snooping Multicast Listener Discovery Snooping Chapter 30 SNMP Commands Provide information about the commands used for configuring the SNMP Simple Network Management Protocol functions Chapter 31 LLDP Commands Provide information about the commands used for configuring LLDP function Chapter 32 Cluster Commands Provide information about the commands used for configuring the Cluster Management function Chapter 1 Using the CLI 1 1 Accessing the CLI You can log on to the switch and access the CLI by the following two methods 1 Log on to the switch by the console port on the switch 2 Log on to the switch remotely by a Telnet or SSH connect
170. oping groups It can be extended to some other commands to display the dynamic and static multicast information of a selected VLAN Syntax show ip igmp snooping groups vlan vian id count dynamic dynamic count static static count Parameter vian id The VLAN ID selected to display the information of all multicast items count The numbers of all multicast groups dynamic Display dynamic multicast groups dynamic count The numbers of all dynamic multicast groups static Display static multicast groups static count The numbers of all static multicast groups Command Mode Privileged EXEC Mode and Any Configuration Mode 212 Example Display the information of all IGMP snooping groups TL SG3424 show ip igmp snooping groups Display all the multicast entries in VLAN 5 TL SG3424 config show ip igmp snooping groups vlan 5 Display the count of multicast entries in VLAN 5 TL SG3424 config show ip igmp snooping groups vlan 5 count Display the dynamic multicast groups of VLAN 5 TL SG3424 config show ip igmp snooping groups vlan 5 dynamic Display the static multicast groups of VLAN 5 TL SG3424 config show ip igmp snooping groups vlan 5 static Display the count of dynamic multicast entries of VLAN 5 TL SG3424 config show ip igmp snooping groups vlan 5 dynamic count Display the count of static multicast entries of VLAN 5 TL SG3424 config show ip igmp snooping groups vlan 5 static co
171. ort s Command Mode Global Configuration Mode Example Configure the static multicast group ff80 1234 in VLAN 2 with the member port gigabitEthernet 1 0 2 TL SG3424 config ipv6 mld snooping vlan 2 static ff80 1234 interface gigabitEthernet 1 0 2 ipv6 mid snooping querier vlan Description The ipv6 mld snooping querier vlan command is used to enable the MLD Querier function To disable this function please use no ipv6 mld snooping querier vlan command 221 Syntax ipv6 mld snooping querier vlan vian id no ipv6 mld snooping querier vlan vian id Parameter vlan id The VLAN that enables the MLD querier function ranging from 1 to 4094 Command Mode Global Configuration Mode Example Enable MLD Querier function on VLAN 2 TL SG3424 config ipv6 mid snooping querier vlan 2 ipv6 mid snooping querier vlan max response time Description The ipv6 mld snooping querier vlan max response time command is used to specify the max response time of the Query message The default value is 10 seconds To restore the default value please use no ipv6 mld snooping querier vlan max response time command Syntax ipv6 mld snooping querier vlan vian id max response time time no ipv6 mld snooping querier vian vian id max response time Parameter vlan id The VLAN that enables the MLD Querier function ranging from 1 to 4094 time Specify the time in seconds ranging from 1 to 25 Command Mode Global
172. ost table Syntax show snmp server host Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Host table TL SG3424 show snmp server host show snmp server enginelD Description The show snmp server enginelD command is used to display the enginelD of the SNMP Syntax show snmp server enginelD Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the enginelD TL SG3424 show snmp server enginelD show rmon history Description The show rmon history command is used to display the configuration of the history sample entry Syntax show rmon history index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 in the format of 1 3 5 You can select more than one entry 247 for each command By default the configuration of all history sample entries is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of all history sample entries TL SG3424 show rmon history show rmon event Description The show rmon event command is used to display the configuration of SNMP RMON Event Syntax show rmon event index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 in the format of 1 3 5 You can select more than one entry for each command By default the configuration of all SN
173. ough console port lts value is 0 in general as there is only one console port on a switch startlinenum The start serial number of the login user selected to configure the login mode and password ranging from O to 15 O means the first login user number 1 means the second and the rest can be done in the same manner endlinenum The end serial number of the login user selected to configure the login mode and password ranging from O to 15 O means the first login user number 1 means the second and the rest can be done in the same manner Command Mode Global Configuration Mode Example Enter the Console port configuration mode and configure the console port 0 TL SG3424 config line console 0 Enter the Virtual Terminal configuration mode so as to prepare further configurations such as password and login mode for virtual terminal O to 5 TL SG3424 config line vty 0 5 password Description The password command is used to configure the connection password To clear the password please use no password command Syntax password 0 password 7 encrypted password no password Parameter 0 Specify the encryption type O indicates that an unencrypted password will follow By default the encryption type is 0 password Connection password a string from 1 to 31 alphanumeric characters or symbols The password is case sensitive allows digits English letters case sensitive underlines and sixteen
174. p SSH 1 RSA 2 SSH 2 BSA SSH 2 DSA Number of bits in a generated key 1024 Figure 1 19 Generate SSH Key note 1 The key length is in the range of 256 to 3072 bits 2 During the key generation randomly moving the mouse quickly can accelerate the key generation 2 After the key is successfully generated please save the public key and private key to a TFTP server 13 i PuTIY Key Generator File Key Conversions Help Key Public key for pasting into OpenSSH authorized_keys file ssh tsa ASAAB3NzaC1 po2EAAAABIOAAAIBoZaDYsiF wslaScst h nySwoUl 3 Jm c4C2y 215 34 R 4yevi8F vfA 4G zxaE CIMMI35wCIhD wD bOBb7ASMim ZY FL WiwnaJOH4SNokrp 6mzQSRDSHJW8TCx1 n3l n lt dpu2ePeS95UK6euE aT ew fOvweR 2e5T CT D Awbe NQ rsa key 20100120 Key fingerprint ssh tsa 1023 38 cd 9e 14 da b1 6a 9e 2b ff 43 69 e5 47 4 50 Key comment rsa key 20140127 Key passphrase Confirm passphrase Actions Generate a public private key pair Generate Load an existing private key file Load Save the generated key Save public key Save private key Parameters Type of key to generate O SSH 1 RSA SSH 2 RSA SSH 2 DSA Number of bits in a generated key 1024 Figure 1 20 Save the Generated Key 3 Log on to the switch by the console port and download the public key file from the TFTP server to the switch as the following figure shows TPLINK HyperTerminal F
175. p hold uf ll 250 ele dr GE 251 ele ue A RA 252 ele e 252 Ap Te 253 NN 253 lp VES leia A A ee 254 eege Eeer ET 255 eege E E EE 255 eege DEE 256 SHOW WAP uv anio ate net oie 257 SHOW MAP INC MACE nsession denier un eiken NEEE ENE EEEE EEEE E npn Rite pe TS 257 show lldp local information Interface 258 show lldp neighbor information Interface 258 Show lldp traffic Interface ica atada 259 Chapter 32 Cluster Command SS 260 Cluster D ENEN eee eee eer eee 260 cluster NAPs PPPOPO5 0 0 P caneevey covenvee EES EEGEN 261 Ee 262 EE 262 Cluster CANGIDALE coin of tic tacos 263 e E le TEE 263 XII SHOW CU O tt tl eta 264 show cluster Otro ote 264 Die ge E e Le lee TEE 265 show cluster manage rOle erea aaah aa deed 265 XIV Preface This Guide is intended for network administrator to provide referenced information about CLI Command Line Interface The switch mentioned in this Guide stands for TL SG3210 TL SG3216 TL SG3424 TL SG3424P without any explanation The commands in this guilde apply to these four models if not specially noted and TL SG3424 is taken as an example model in the example commands Overview of this Guide Chapter 1 Using the CLI Provide information about how to use the CLI CLI Command Modes Security Levels and some Conventions Chapter 2 User Interface Provide information about the commands used to switch between five CLI Command Modes Chapter 3 IEEE 802 1Q VLAN Commands Provide informa
176. p http secure server command Only the SSL function is enabled a secure HTTPS connection can be established Syntax ip http secure server no ip http secure server Command Mode Global Configuration Mode Example Enable the SSL function TL SG3424 config ip http secure server ip http secure server download certificate Description The ip http secure server download certificate command is used to download a certificate to the switch from TFTP server Syntax ip http secure server download certificate ss cert ip address p addr 100 Parameter ssl cert The name of the SSL certificate which is selected to download to the switch The length of the name ranges from 1 to 25 characters The Certificate must be BASE64 encoded ip addr The IP address of the TFTP server Both IPv4 and IPv6 addresses are supported for example 192 168 0 1 or fe80 1234 Command Mode Global Configuration Mode Example Download an SSL Certificate named ssl cert from TFTP server with the IP address of 192 168 0 146 TL SG3424 config ip http secure server download certificate ssl cert ip address 192 168 0 146 Download an SSL Certificate named ssl cert from TFTP server with the IP address of fe80 1234 TL SG3424 config ip http secure server download certificate ssl cert ip address fe80 1234 ip http secure server download key Description The ip http secure server download key command is used to download an
177. ping information circuit id ooooocccccnonocccononaccccnonancncnononcnnnonnn cnn conan cnn nan ncnnnannnnno 66 IP UNCP SNOOPING trUSt eee eeeeceececse a a ea a ae a eE Ea 67 ip dhcp snooping mac verify 2 0 eee cece cece eee eeene eee eeeeeeeeeeeeaeeeeeecaaeeeeceaeeeeescaeeeeeseneeeeeeeseneeeeseeas 67 ip dhcp Snooping limit rate ooooococcnnnococcnnoncccccnanaccncnnnrnnnnonnnnconnnnncnnnnnnn cnn cnn cnn nn nnannn cc nninnnnn 68 lic elle Bet TE 68 ANA Te EE 69 SHOW IP GHGp SNOOPING aldea n 69 show ip dhcp snooping information ccccccccceeeeeceeeeeeeneeeeeeeeeeeeeceeeeeeeseceeeeseseeeeesseeeeeseees 70 show ip dhcp snooping interface oigabittthemet 70 Chapter 11 ARP Inspection Commande AAA 72 ip arp inspection Elo ba alada 72 IP APP INSPECTION Drust cnn ee ea aaaea a ee aaia a en aa 72 iparp inspection internfaCe iiiii 6 A EEEE A eee REEE enced 73 IP Arp Inspection mitate EE 74 IP AarpsINSPECtION TECOVE Me teiert cranes ace AAA 74 NA a reer sherssgnetee etek apenasnedentasned eetaseeteedl suas 75 show ip arp inspection Interface 75 show ip arp inspection staietics cnn nnnnn cnn conan nnccnnnnnss 76 clear ip arp inspection statistics siisii aaa aia aai aE EEE EEE 76 Chapter 12 DoS Defend Commande 77 RS TTT 77 deefe ele ET 77 SHOW ip DOS TE EE 78 Chapter 13 IEEE 02 1 rte 79 dotlx system auth COntrol tania tb E 79 eleng e tu Eu e TTT 79 dot1x guest vlantiglobal cnn nonnnnnn cnn nan nnncnannnnnnn
178. power limit is 5w TL SG3424P config power profile IP Camera supply enable priority low consumption 50 power time range Description The power time range command is used to create PoE time range for the switch and enter Power Time range Create Configuration Mode After a PoE time range is created you need to specify the date and time which has three mode options available absolute periodic and holiday A PoE time range can implement multiple time ranges simultaneously as long as they do not conflict with each other To delete the corresponding PoE time range configuration please use no power time range command The PoE time range determines the power supply time of the switch You can specify a PoE time range for each POE port individually Syntax power time range name no power time range name Parameter name The POE time range name ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Create a PoE time range named tRange1 for the switch TL SG3424P config power time range tRange1 163 power holiday Description The power holiday command is used to create PoE holiday for the switch To delete the corresponding PoE holiday configuration please use no power holiday command Syntax power holiday name start date start date end date end date no power holiday name Parameter name The PoE holiday name ranging from 1 to 16 characters start date The star
179. pply power include Indicates the PoE time range of the switch including the PoE holiday It is the default option When PoE holiday occurs the switch will supply power Command Mode Power Time range Create Configuration Mode Example Create a holiday mode time range for the PoE time range named tRange3 and configure PoE time range of the switch excludes the PoE holiday TL SG3424P config power time range tRange3 TL SG3424P config pwr time range holiday exclude power inline consumption interface Description The power inline consumption command is used to configure the power limit the corresponding port can supply Syntax power inline consumption power limit auto class1 class2 class3 class4 166 Parameter power limit The max power the port in the profile can supply with five options power limit auto class1 class2 class3 and class4 Power limit indicates you can manually enter a value ranging from 1 to 300 The value is in the unit of 0 1 watt For instance if you want to configure the max power as 5w you should enter 50 Auto indicates the value is assigned automatically by the PoE switch Class1 represents 4w Class2 represents 7w Class3 represents 15 4w Class4 represents 30w Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the
180. ption The absolute command is used to configure a Time Range into an absoluteness mode To delete the corresponding absoluteness mode Time range please use no absolute command Syntax absolute start start date end end date no absolute 172 Parameter start date The start date in Absoluteness Mode in the format of MM DD YYYY By default it is 01 01 2000 end date The end date in Absoluteness Mode in the format of MM DD YYYY By default it is 12 31 2000 The absoluteness mode will be disabled if the start date and end date are both in default value Command Mode Time range Create Configuration Mode Example Configure the time range tSeg1 with time from May 5 2012 to Oct 5 2012 TL SG3424 config time range tSeg1 TL SG3424 config time range absolute start 05 05 2012 end 10 05 2012 periodic Description The periodic command is used to configure the Time Range into an periodic mode To delete the corresponding periodic mode Time Range please use no periodic command Syntax periodic week date week day time slice1 fime slice time slice2 time slice time slice3 time slice time slice4 time slice no periodic Parameter week day Periodic Mode in the format of 1 3 6 or daily off day working day 1 3 6 represent Monday Tuesday Wednesday and Saturday daily represents every day off day represents weekend and working day represents working day By default the periodic mode is di
181. queue mode Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the schedule rule of the egress queues TL SG3424 show qos queue mode 149 show qos status Description The show qos status command is used to display the status of IEEE 802 1P priority and DSCP priority Syntax show qos status Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the status of IEEE 802 1P priority and DSCP priority TL SG3424 show qos status 150 Chapter 22 Port Mirror Commands Port Mirror refers to the process of forwarding copies of packets from one port to a monitoring port Usually the monitoring port is connected to data diagnose device which is used to analyze the monitored packets for monitoring and troubleshooting the network monitor session destination interface Description The monitor session destination interface command is used to configure the monitoring port Each monitor session has only one monitoring port To change the monitoring port please use the monitor session destination interface command by changing the port value The no monitor session command is used to delete the corresponding monitor session Syntax monitor session session_num destination interface gigabitEthernet port no monitor session session_num Parameter session_num The monitor session number ranging from 1 to 4 port The Ethernet port number Command Mode Global Configuration
182. r the SNMP management station to manage MIB objects Syntax snmp server view name mib oid include exclude no snmp server view name mib oid Parameter name The entry name of View ranging from 1 to 16 characters Each View includes several entries with the same name 231 mib oid MIB Object ID It is the Object Identifier OID for the entry of View ranging from 1 to 61 characters include exclude View Type with include and exclude options They represent the view entry can cannot be managed by the SNMP management station individually Command Mode Global Configuration Mode Example Add a View named view1 configuring the OID as 1 3 6 1 6 3 20 and this OID can be managed by the SNMP management station TL SG3424 config snmp server view view1 1 3 6 1 6 3 20 include snmp server group Description The snmp server group command is used to manage and configure the SNMP group To delete the corresponding SNMP group please use no snmp server group command SNMP v3 provides the VACM View based Access Control Model and USM User Based Security Model mechanisms for authentication The users in the SNMP Group can manage the device via the Read View Write View and Notify View And the authentication mode and the privacy mode guarantee the high security for the communication between the management station and the managed device Syntax snmp server group name smode v1 v2c v3 slev noAut
183. r time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 206 leave time Leave Time which is the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 port The Ethernet port number Command Mode Global Configuration Mode Example Enable Multicast VLAN 3 and configure Router Port Time as 100 seconds Member Port Time 100 seconds Leave Time 3 seconds and Static Router Port port 3 TL SG3424 config ip igmp snooping multi vlan config 3 rtime 100 TL SG3424 config ip igmp snooping multi vlan config 3 mtime 100 TL SG3424 config ip igmp snooping multi vlan config 3 Itime 3 TL SG3424 config ip igmp snooping multi vlan config 3 rport interface gigabitEthernet 1 0 3 ip igmp snooping filter add id Description The ip igmp snooping filter add id command is used to configure the multicast IP range desired to filter To delete the corresponding IP range please use no ip igmp snooping filter add id command When IGMP Snooping is enabled you can specified the multicast IP range the ports can join so as to restrict users ordering multicast programs via configuring multicast filter rules Multicast
184. ree for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if spanning tree guard tc spanning tree mcheck Description The spanning tree mcheck command is used to enable MCheck Syntax spanning tree mcheck Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable MCheck for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if spanning tree mcheck show spanning tree active Description The show spanning tree active command is used to display the active information of spanning tree Syntax show spanning tree active Command Mode Privileged EXEC Mode and Any Configuration Mode 199 Example Display the active information of spanning tree TL SG3424 config show spanning tree active show spanning tree bridge Description The show spanning tree bridge command is used to display the bridge parameters Syntax show spanning tree bridge forward time hello time hold count max age max hops mode priority state Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the bridge parameters TL SG3424 config show spanning tree bridge show spanning tree interface Description The show spanning tree interface command is used to display the spanning tree information of all ports or a specified port Syntax show spanning tree interface gigabi
185. ress Syntax show mac address table address mac addr Parameter mac addr The specified MAC address Command Mode Privileged EXEC Mode and Any Configuration Mode 108 Example Display the information of the MAC address 00 00 00 00 23 00 TL SG3424 config show mac address table address 00 00 00 00 23 00 show mac address table vlan Description The show mac address table vlan command is used to display the MAC address configuration of the specified vlan Syntax show mac address table vlan vid Parameter vid The specified VLAN id Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the MAC address configuration of vlan 1 TL SG3424 config show mac address table vlan 1 109 Chapter 18 System Configuration Commands System Configuration Commands can be used to configure the system information and system IP of the switch and to reboot and reset the switch upgrade the switch system and commands used for device diagnose including loopback test and cable test system time manual Description The system time manual command is used to configure the system time manually Syntax system time manual time Parameter time Set the date and time manually in the format of MM DD YYYY HH MM SS Command Mode Global Configuration Mode Example Configure the system time as 02 14 2012 12 30 00 TL SG3424 config system time manual 02 14 2012 12 30 00 system time n
186. rmation TL SG3424 config show ipv6 mld snooping querier show ipv6 mid snooping statistics Description The show ipv6 mid snooping statistics command is used to display the statistics of the MLD packets Syntax show ipv6 mld snooping statistics interface gigabitEthernet port Parameter port Specify the port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display statistics of MLD packets TL SG3424 config show ipv6 mld snooping statistics 230 Chapter 30 SNMP Commands SNMP Simple Network Management Protocol functions are used to manage the network devices for a smooth communication which can facilitate the network administrators to monitor the network nodes and implement the proper operation snmp server Description The snmp server command is used to enable the SNMP function By default it is disabled To return to the default configuration please use no snmp server command Syntax snmp server no snmp server Command Mode Global Configuration Mode Example Enable the SNMP function TL SG3424 config snmp server snmp server view Description The snmp server view command is used to add View To delete the corresponding View please use no snmp server view command The OID Object Identifier of the SNMP packets is used to describe the managed objects of the switch and the MIB Management Information Base is the set of the OIDs The SNMP View is created fo
187. rol broadcast command Broadcast control function allows the switch to filter broadcast in the network If the transmission rate of the broadcast packets exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control broadcast rate rate no storm control broadcast Parameter rate Specify the bandwidth for receiving broadcast packets on the port The packet traffic exceeding the bandwidth will be discarded The value of it can be 128k 256k 512k 1m 2m 4m 5m 10m 20m 40m 50m in bps By default the value is 128K 136 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the broadcast control function for port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if storm control broadcast storm control multicast Description The storm control multicast command is used to enable the multicast control function To disable the multicast control function please use no storm control multicast command Multicast control function allows the switch to filter multicast in the network If the transmission rate of the multicast packets exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control multicast rate rate no storm control multicast Parameter rate Select the bandwid
188. rs after changes occur so as to prevent LLDPDU being sent frequently By default it is 2 seconds reinit delay This parameter indicates the amount of delay from when LLDP status becomes disable until re initialization will be attempted The value ranges from 1 to 10 seconds and the default value is 3 seconds notify interval Specify the interval of Trap message which will be sent from local device to network management system The value ranges from 5 to 3600 seconds and the default value is 5 seconds fast count When the port s LLDP state transforms from Disable or Rx_Only to Tx amp Rx or Tx_Only the fast start mechanism will be enabled that is the transmit interval will be shorten to a second and several LLDPDUs will be sent 251 out the number of LLDPDUs equals this parameter The value ranges from 1 to 10 and the default value is 3 Command Mode Global Configuration Mode Example Specify the Transmit Interval of LLDPDU as 45 seconds and Trap message to NMS as 120 seconds TL SG3424P config lldp timer tx interval 45 TL SG3424P config lldp timer notify interval 120 lldp med fast count Description The Ildp med fast count command is used to configure the number of the LLDP MED frames that will be sent out When LLDP MED fast start mechanism is activated multiple LLDP MED frames will be transmitted based on this parameter The default value is 4 To return to the default configuration please
189. rt number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the description of all Ethernet ports TL SG3424 config show interface description Display the description of port 2 TL SG3424 config show interface gigabitEthernet 1 0 2 description show interface flowcontrol Description The show interface flowcontrol command is used to display the flow control information of an Ethernet port Syntax show interface gigabitEthernet port flowcontrol Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the flow control information of all Ethernet ports TL SG3424 show interface flowcontrol Display the flow control information of port 2 TL SG3424 show interface gigabitEthernet 1 0 2 flowcontrol 141 show interface configuration Description The show interface configuration command is used to display the configurations of all ports or an Ethernet port including Port status Flow Control Negotiation Mode and Port description Syntax show interface gigabitEthernet port configuration Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configurations of all Ethernet ports TL SG3424 config show interface configuration Display the configurations of port 2 TL SG3424 config show interface gigabitEthernet 1 0 2 configurat
190. s none encrypt pwd Privacy Password ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add Local User admin to Group group2 and configure the Security Model of the user as v3 the Security Level of the group as authPriv the Authentication Mode of the user as MD5 the Authentication Password as 11111 the Privacy Mode as DES and the Privacy Password as 22222 TL SG3424 config snmp server user admin local group2 smode v3 slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222 234 snmp server community Description The snmp server community command is used to add Community To delete the corresponding Community please use no snmp server community command SNMP v1 and SNMP v2c adopt community name authentication The community name can limit access to the SNMP agent from SNMP network management station functioning as a password Syntax snmp server community name read only read write mib view no snmp server community name Parameter name Community Name ranging from 1 to 16 characters read only read write The access rights of the community with read only and read write options mib view The MIB View for the community to access Command Mode Global Configuration Mode Example Add community public and the community has read write management right to View viewDefault TL SG3424 config snmp server community public read write viewDefault snmp server
191. s queue To return to the default configuration please use no qos queue cos map command When 802 1P Priority is enabled the packets with 802 1Q tag are mapped to different priority levels based on 802 1P priority mode The untagged packets are mapped based on port priority mode Syntax qos queue cos map fag cos id tc id no qos queue cos map Parameter tag cos id The 8 priority levels defined by IEEE 802 1P or the priority level the packets with tag are mapped to which ranges from CoS 0 to CoS 7 tc id The egress queue the packets with tag are mapped to It ranges from 0 to 3 which represents TCO TC1 TC2 TC3 respectively Command Mode Global Configuration Mode 145 User Guidelines 1 By default the mapping relation between tag cos and the egress queue is 0 TC1 1 TCO 2 TCO 3 TC1 4 TC2 5 TC2 6 TC3 7 TC3 2 Among the priority levels TCO TC3 the bigger value the higher priority Example Map CoS 5 to TC 2 TL SG3424 config qos queue cos map 5 2 qos queue dscp map Description The qos queue dscp map command is used to configure the mapping relation between DSCP Priority and the CoS value To return to the default configuration please use no qos queue dscp map command DSCP DiffServ Code Point is a new definition to IP ToS field given by IEEE This field is used to divide IP datagram into 64 priorities When DSCP Priority is enabled IP datagram are mapped to different priority levels bas
192. s which include four types linkup linkdown warmstart and coldstart To disable the sending of SNMP standard traps please use no snmp server traps snmp command snmp server traps snmp linkup linkdown warmstart coldstart auth failure no snmp server traps snmp linkup linkdown warmstart coldstart auth failure Parameter linkup Enable linkup trap It is sent when port status changes from linkdown to linkup By default it is enabled linkdown Enable linkdown trap It is sent when port status changes from linkup to linkdown By default it is enabled warmstart Enable warmstart trap It is sent upon SNMP function reboot By default it is enabled coldstart Enable coldstart trap It is sent upon switch reboot By default it is enabled auth failure Enable the auth failure trap It is sent when a received SNMP request fails the authentication By default it is enabled Command Mode Global Configuration Mode Example Enable SNMP standard linkup trap for the switch TL SG3424 config snmp server traps snmp linkup snmp server traps link status Description Syntax The snmp server traps link status command is used to enable SNMP link status trap for the specified port To disable the sending of SNMP link status trap please use no snmp server traps link status command 238 snmp server traps link status no snmp server traps link status Command Mode Int
193. sabled time slice Create the time slice in the format of HH MM HH MM Command Mode Time range Create Configuration Mode Example Configure the time range tSeg1 with time from 8 30 to 12 00 at weekend TL SG3424 config time range tSeg1 173 TL SG3424 config time range periodic week date off day time slice1 08 30 12 00 holiday Description The holiday command is used to configure the time range into Holiday Mode under Time range Create Configuration Mode To delete the corresponding Holiday Mode time range please use no holiday command Syntax holiday no holiday Command Mode Time range Create Configuration Mode Example Configure the time range tSeg1 into Holiday Mode TL SG3424 config time range tSeg1 TL SG3424 config time range holiday holiday global Description The holiday command is used to define a holiday To delete the corresponding holiday please use no holiday command Syntax holiday name start date start date end date end date no holiday Parameter name The holiday name ranging from 1 to 16 characters start date The start date of the holiday in the format of MM DD for instance 05 01 end date The end date of the holiday in the format of MM DD for instance 05 03 Command Mode Global Configuration Mode 174 Example Define National Day configuring the start date as October 1st and the end date as October 3rd TL SG3424 config holid
194. sage to be sent The default value is 2 To restore the default number please use no ipv6 mld snooping last listener query count command Syntax ipv6 mld snooping last listener query count num no ipv6 mld snooping last listener query count Parameter num Specify the numbers of Specific Query Message to be sent ranging from 1 to 7 Command Mode Global Configuration Mode Example Specify the number of Specific Query Message to 3 TL SG3424 config ipv6 mid snooping last listener query count 3 ipv6 mid snooping multicast vlan Description The ipv6 mld snooping multicast vlan command is used to enable the multicast VLAN function To disable this function please use no ipv6 mld snooping multicast vlan command By default it is disabled Syntax ipv6 mld snooping multicast vlan no ipv6 mld snooping multicast vlan Command Mode Global Configuration Mode Example Enable multicast VLAN TL SG3424 config ipv6 mld snooping multicast vlan 217 ipv6 mid snooping multicast vlan vlan id Description The ipv6 mld snooping multicast vlan vlan id command is used to specify the multicast VLAN ID The default multicast VLAN is VLAN1 To restore the default VLAN please use no ipv6 mid snooping multicast vlan vlan id command Syntax ipv6 mld snooping multicast vlan vlan id vid no ipv6 mld snooping multicast vlan vlan id Parameter vid The specified IEEE 802 1Q VLAN ID ranging from 1 to 4094 Command Mode
195. sed to backup the configuration file to TFTP server 119 Syntax copy startup config tftp ip address p addr filename name Parameter ip addr IP Address of the TFTP server Both IPv4 and IPv6 addresses are supported for example 192 168 0 1 or fe80 1234 name Specify the name for the configuration file which would be backup Command Mode Privileged EXEC Mode Example Backup the configuration files to TFTP server with the IP 192 168 0 148 and name this file config cfg TL SG3424 copy startup config tftp ip address 192 168 0 148 filename config Backup the configuration files to TFTP server with the IP fe80 1234 and name this file config cfg TL SG3424 copy startup config tftp ip address fe80 1234 filename config copy tftp startup config Description The copy tftp startup config command is used to download the configuration file to the switch from TFTP server Syntax copy tftp startup config ip address p addr filename name Parameter ip addr IP Address of the TFTP server Both IPv4 and IPv6 addresses are supported for example 192 168 0 1 or fe80 1234 name Specify the name for the configuration file which would be downloaded Command Mode Privileged EXEC Mode Example Download the configuration file named as config cfg to the switch from TFTP server with the IP 192 168 0 148 120 TL SG3424 copy tftp startup config ip address 192 168 0 148 filename config Download the co
196. set or change the password for users to access Privileged EXEC Mode from User EXEC Mode To remove the password please use no enable password command This command uses the symmetric encryption Syntax enable password 0 password 7 encrypted password no enable password Parameter 0 Specify the encryption type O indicates that an unencrypted password will follow By default the encryption type is 0 password Super password a string from 1 to 31 alphanumeric characters or symbols The password is case sensitive allows digits English letters case sensitive underlines and sixteen special characters By default it is empty 7 Indicates a symmetric encrypted password with fixed length will follow encrypted password A symmetric encrypted password with fixed length which you can copy from another switch s configuration file After the encrypted password is configured you should use the corresponding unencrypted password if you re enter this mode Command Mode Global Configuration Mode User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service password encryption the password in the configuration file will be displayed in the symmetric encrypted form Example Set the super password as admin and unencrypted to access Privileged EXEC Mode from User EXEC Mode TL SG3424 config enable password
197. sion revision Parameters revision The revision level for MST region identification ranging from O to 65535 Command Mode MST Configuration Mode Example Configure the revision level of MST as 100 TL SG3424 config spanning tree mst configuration TL SG3424 config mst revison 100 191 spanning tree mst instance Description The spanning tree mst instance command is used to configure the priority of MST instance To return to the default value of MST instance priority please use no spanning tree mst instance command Syntax spanning tree mst instance instance id priority pri no spanning tree mst instance instance id priority Parameter instance id Instance ID ranging from 1 to 8 pri MSTI Priority which must be multiple of 4096 ranging from 0 to 61440 By default it is 32768 MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance Command Mode Global Configuration Mode Example Enable the MST Instance 1 and configure its priority as 4096 TL SG3424 config spanning tree mst instance 1 priority 4096 spanning tree mst Description The spanning tree mst command is used to configure MST Instance Port To return to the default configuration of the corresponding Instance Port please use no spanning tree mst command A port can play different roles in different spanning tree instance You can use this command to configure
198. snap and llc options template idx The number of the Protocol based VLAN Template You can get the template corresponding to the number by the show protocol vlan template command Command Mode Global Configuration Mode Example Create a Protocol based VLAN template named TP whose Ethernet protocol type is 0x2024 and frame type is Ethernetll TL SG3424 config protocol vian template name TP ether type 2024 frame ether_2 34 protocol vlan vlan Description The protocol vlan vlan command is used to create a Protocol based VLAN To delete a Protocol based VLAN please use no protocol vlan command Syntax protocol vlan vlan vian id template template idx no protocol vlan vlan group idx Parameter vlan vid Specify IEEE 802 1Q VLAN ID ranging from 1 4094 template idx The number of the Protocol based VLAN Template You can get the template corresponding to the number by the show protocol vlan template command group idx The number of the Protocol based VLAN entry You can get the Protocol based VLAN entry corresponding to the number by the show protocol vlan vian command Command Mode Global Configuration Mode Example Create Protocol based VLAN 2 and bind it with Protocol based VLAN Template 3 TL SG3424 config protocol vian vian 2 template 3 protocol vlan group Description The protocol vlan group command is used to create a Protocol based VLAN group To delete
199. special characters 15 0 I KI By default it is empty 7 Indicates a symmetric encrypted password with fixed length will follow 57 encrypted password A symmetric encrypted password with fixed length which you can copy from another switch s configuration file After the encrypted password is configured you should use the corresponding unencrypted password if you re enter this mode Command Mode Line Configuration Mode User Guidelines If the password you configured here is unencrypted and the global encryption function is enabled in service password encryption the password in the configuration file will be displayed in the symmetric encrypted form Example Configure the connection password of Console port connection 0 as tplink and unencrypted TL SG3424 config line console 0 TL SG3424 config line password 0 tplink Configure the connection password of virtual terminal connection 0 5 as tplink and unencrypted TL SG3424 config line vty 0 5 TL SG3424 config line password 0 tplink login Description The login command is used to configure the login of a switch without using the default user name and password At this situation a connection password must be set for virtual terminal connection Syntax login Command Mode Line Configuration Mode Example Configure the login of Console port connection O as login mode TL SG3424 config line console 0 58 TL SG3424 conf
200. splay the related information of MST Instance Syntax show spanning tree mst configuration digest instance instance id interface gigabitEthernet port 201 Parameter instance id Instance ID desired to show ranging from 1 to 8 port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the related information of MST Instance 1 TL SG3424 config show spanning tree mst instance 1 202 Chapter 28 IGMP Snooping Commands IGMP Snooping Internet Group Management Protocol Snooping is a multicast control mechanism running on Layer 2 switch It can effectively prevent multicast groups being broadcasted in the IPv4 network ip igmp snooping global Description The ip igmp snooping command is used to configure IGMP Snooping globally To disable the IGMP Snooping function please use no ip igmp snooping command Syntax ip igmp snooping no ip igmp snooping Command Mode Global Configuration Mode Example Enable IGMP Snooping function TL SG3424 config ip igmp snooping ip igmp snooping interface Description The ip igmp snooping command is used to enable the IGMP Snooping function for the desired port To disable the IGMP Snooping function please use no ip igmp snooping command Syntax ip igmp snooping no ip igmp snooping Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet
201. ssword Authentication Mode 1 Open the software to log on to the interface of PUTTY Enter the IP address of the switch into Host Name field keep the default value 22 in the Port field select SSH as the Connection type 11 2 X PuTTY Configuration Category Session Logging Terminal Keyboard Bell Features Window Appearance Behaviour Translation Selection Colours Connection Data Proxy Telnet Rlogin Kex Auth TTY x11 Basic options for your PuTTY session Specify the destination you want to connect to Host Name or IP address l Port 192 168 0 1 22 Connection type ORaw O Telnet O Alogin SSH Serial Load save or delete a stored session Saved Sessions Default Settings Close window on exit Odlways ONever Only on clean exit Figure 1 17 SSH Connection Config Click the Open button in the above figure to log on to the switch Enter the login user name and password to log on the switch and then enter the Privileged EXEC Mode password so you can continue to configure the switch 192 168 0 1 PuTIY i admin Figure 1 18 Log on the Switch gt Key Authentication Mode 1 Select the key type and key length and generate SSH key 12 PulTY Key Generator je File Key Conversions Help Key No key Actions Generate a public private key pair Generate a key Load an existing private key file Save the generated key Parameters Type of key to generate Key ty
202. switch is powered Syntax history Command Mode Privileged EXEC Mode and any Configuration Mode Example Show the commands you have entered in the current mode 24 TL SG3424 config history 1 history history clear Description The history clear command is used to clear the commands you have entered in the current mode therefore these commands will not be shown next time you use the history command Syntax history clear Command Mode Privileged EXEC Mode and any Configuration Mode Example Clear the commands you have entered in the current mode TL SG3424 config history clear 25 Chapter 3 IEEE 802 1Q VLAN Commands VLAN Virtual Local Area Network technology is developed for the switch to divide the LAN into multiple logical LANs flexibly Hosts in the same VLAN can communicate with each other regardless of their physical locations VLAN can enhance performance by conserving bandwidth and improve security by limiting traffic to specific domains vian Description The vlan command is used to create IEEE 802 1Q VLAN and enter VLAN Configuration Mode To delete the IEEE 802 1Q VLAN please use no vlan command Syntax vlan vian list no vlan vian list Parameter vlan list Specify IEEE 802 1Q VLAN ID list ranging from 2 to 4094 in the format of 2 3 5 It is multi optional Command Mode Global Configuration Mode Example Create VLAN 2 10 and VLAN 100 TL SG3424 config vlan 2 10 100
203. t Syntax s mirror interface gigabitEthernet port Parameter port The Mirror Port number of Stream Mirror Command Mode Action Configuration Mode Example Edit the actions for policy1 Specify the mirror port for the data packets matching ACL 120 as port 2 TL SG3424 config access list policy action policy1 120 TL SG3424 config action s mirror interface gigabitEthernet 1 0 2 qos remark Description The qos remark command is used to configure QoS Remark function of policy action To delete the corresponding policy action please use no qos remark command 182 Syntax qos remark dscp dscp priority pri no qos remark Parameter dscp DSCP of QoS Remark Specify the DSCP region for the data packets matching the corresponding ACL DSCP ranges from 0 to 63 By default it is not limited pri Local Priority of QoS Remark Specify the local priority for the data packets matching the corresponding ACL Local Priority ranges from 0 to 3 Command Mode Action Configuration Mode Example Edit the actions for policy1 For the data packets matching ACL 120 specify the DSCP region as 30 and local priority 2 TL SG3424 config access list policy action policy1 120 TL SG3424 config action qos remark dscp 30 priority 2 access list bind interface Description The access list bind command is used to bind a policy to a specified port To cancel the bind relation please use no access list bind command Synt
204. t date of the PoE holiday in the format of MM DD for instance 05 01 end date The end date of the PoE holiday in the format of MM DD for instance 05 01 Command Mode Global Configuration Mode Example Create a PoE holiday named National Day and configure the start date as October 1st and the end date as October 3rd TL SG3424P config power holiday NationalDay start date 10 01 end date 10 03 absolute Description The absolute command is used to create an absolute mode time range for the PoE time range of the switch The switch will supply power when the specified absolute time occurs To delete the corresponding absolute mode time range configuration please use no absolute command Syntax absolute start start date end end date no absolute 164 Parameter start date The start date in Absoluteness Mode in the format of MM DD YYYY end date The end date in Absoluteness Mode in the format of MM DD YYYY Command Mode Power Time range Create Configuration Mode Example Create an absolute mode time range for the PoE of the switch and specify the date extending from May 5 2012 through Oct 5 2012 TL SG3424P config power time range tRange1 TL SG3424P config pwr time range absolute start 05 05 2012 end 10 05 2012 periodic Description The periodic command is used to create a periodic mode time range for the POE time range of the switch The switch will supply power when the specifi
205. t limited but it can t be the monitoring port at the same time 3 Whether the monitoring port and monitored ports are in the same VLAN or not is not demanded strictly 4 The monitoring port and monitored ports cannot be link aggregation member Example Create monitor session 1 then configure port 4 5 7 as monitored port and enable ingress monitoring 152 TL SG3424 config monitor session 1 source interface gigabitEthernet 1 0 4 5 1 0 7 rx Delete port 4 in monitor session 1 and its configuration TL SG3424 config no monitor session 1 source interface gigabitEthernet 1 0 4 rx show monitor session Description The show monitor session command is used to display the configuration of port monitoring Syntax show monitor session session_num Parameter session_num The monitor session number ranging from 1 to 4 It is optional By default the monitoring configuration of all monitor sessions is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the monitoring configuration of monitor session 1 TL SG3424 config show monitor session 1 Display the monitoring configuration of all monitor sessions TL SG3424 config show monitor session 153 Chapter 23 Port Isolation Commands Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are not on its forwarding
206. t of xx xx Xx XX XX XX One or several values can be typed for a port list or a vlan list using comma to separate Use a hyphen to designate a range of values for instance 1 0 1 1 0 3 5 1 0 7 indicates choosing port 1 0 1 1 0 3 1 0 4 1 0 5 1 0 7 The port number should format as 1 0 3 meaning unit slot port The unit number is always 1 and slot number is always O and the port number is a variable an actual value must be assigned 19 Chapter 2 User Interface enable Description The enable command is used to access Privileged EXEC Mode from User EXEC Mode Syntax enable Command Mode User EXEC Mode Example If you have set the password to access Privileged EXEC Mode from User EXEC Mode TL SG3424 gt enable Enter password TL SG3424 service password encryption Description The service password encryption command is used to encrypt the password when the password is defined or when the configuration is written using the symmetric encryption algorithm Encryption prevents the password from being readable in the configuration file To disable the global encryption function please use no service password encryption command Syntax service password encryption no service password encryption Command Mode Global Configuration Mode Example Enable the global encryption function TL SG3424 config service password encryption 20 enable password Description The enable password command is used to
207. t respond to the authentication request from the same supplicant during the Quiet Period reauth period time The maximum time for the switch to wait for the response from supplicant before resending a request to the supplicant ranging from 1 to 9 in second By default it is 3 Command Mode Global Configuration Mode 81 Example Configure the quiet period as 100 seconds TL SG3424 config dot1x timeout quiet period 100 dot1x max reauth req Description The dot1x max reauth req command is used to configure the maximum transfer times of the repeated authentication request when the server cannot be connected To restore to the default value please use no dot1x max reauth req command Syntax dot1x max reauth req times no dot1x max reauth req Parameter times The maximum transfer times of the repeated authentication request ranging from 1 to 9 in times By default the value is 3 Command Mode Global Configuration Mode Example Configure the maximum transfer times of the repeated authentication request as 5 TL SG3424 config dot1x max reauth req 5 dot1x Description The dot1x command is used to enable the IEEE 802 1X function for a specified port To disable the IEEE 802 1X function for a specified port please use no dot1x command Syntax dot1x no dot1x 82 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example E
208. t the idx Pay attention to that the entry number is the actual number in the binding table not arranged in an order 61 Command Mode Global Configuration Mode Example Bind an entry with the IP 192 168 0 1 MAC 00 00 00 00 00 01 VLAN ID 2 and Port number 5 manually And then enable the entry for the ARP detection TL SG3424 config ip source binding host1 192 168 0 1 00 00 00 00 00 01 vlan 2 interface gigabitEthernet 1 0 5 arp detection Delete the IP MAC VID PORT entry with the index 5 TL SG3424 config no ip source binding index 5 ip source binding index Description The ip source binding index command is used to modify the existing entry of ip source binding Syntax ip source binding index idx hostname hostname mac mac addr vlan vian id interface gigabitEthernet port none arp detection Parameter idx The entry number needed to be modified You can use the show ip source binding command to get the idx Pay attention that the entry number is the actual number in the binding table which is not displayed in an arranged order hostname The modified Host Name which contains 20 characters at most mac addr The modified MAC address of the Host vlan id The modified VLAN ID ranging from 1 to 4094 port The modified number of port connected to the Host none arp detection The modified protect type for the entry none indicates applying none arp detect
209. tEthernet 1 0 2 TL SG3424 config if ip dhcp snooping trust ip dhcp snooping mac verify Description The ip dhcp snooping mac verify command is used to enable the MAC Verify feature To disable the MAC Verify feature please use no ip dhcp snooping mac verify command There are two fields of the DHCP packet containing the MAC address of the Host The MAC Verify feature is to compare the two fields and discard the packet if the two fields are different Syntax ip dhcp snooping mac verify no ip dhcp snooping mac verify Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet 67 Example Enable the MAC Verify feature for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ip dhcp snooping mac verify ip dhcp snooping limit rate Description The ip dhcp snooping limit rate command is used to enable the Flow Control feature for the DHCP packets The excessive DHCP packets will be discarded To restore to the default configuration please use no ip dhcp snooping limit rate command Syntax ip dhcp snooping limit rate value no ip dhcp snooping limit rate Parameter value The value of Flow Control The options are 0 5 10 15 20 25 30 packet second The default value is 0 which stands for disable Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Set the Flow Control of port
210. tEthernet port edge ext cost int cost mode p2p priority role state status Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the spanning tree information of all ports TL SG3424 config show spanning tree interface Display the spanning tree information of port 2 200 TL SG3424 config show spanning tree interface gigabitEthernet 1 0 2 Display the spanning tree mode information of port 2 TL SG3424 config show spanning tree interface gigabitEthernet 1 0 2 mode show spanning tree interface security Description The show spanning tree interface security command is used to display the protect information of all ports or a specified port Syntax show spanning tree interface security gigabitEthernet port bpdufilter bpduguard loop root tc tc defend Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the protect information of all ports TL SG3424 config show spanning tree interface security Display the protect information of port 1 TL SG3424 config show spanning tree interface security gigabitEthernet 1 0 1 Display the interface security bpdufilter information TL SG3424 config show spanning tree interface security bpdufilter show spanning tree mst Description The show spanning tree mst command is used to di
211. th for receiving multicast packets on the port The packet traffic exceeding the bandwidth will be discarded The value of it can be 128k 256k 512k 1m 2m 4m 5m 10m 20m 40m 50m in bps By default the value is 128K Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the multicast control function for port 5 TL SG3424 config interface gigabitEthernet 1 0 5 TL SG3424 config if storm control multicast 137 storm control unicast Description The storm control unicast command is used to enable the unicast control function To disable the unicast control function please use no storm control unicast command Unicast control function allows the switch to filter UL frame in the network If the transmission rate of the UL frames exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control unicast rate rate no storm control unicast Parameter rate Select the bandwidth for receiving UL Frame on the port The packet traffic exceeding the bandwidth will be discarded The value of it can be 128k 256k 512k 1m 2m 4m 5m 10m 20m 40m 50m in bps By default the value is 128K Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the unicast control function for port 5 TL
212. th pri ip auth sec ip auth port port acct pri ip acct sec jp acct port port auth key O password 7 encrypted password y acct key 0 password 7 encrypted password no radius auth port auth key auth pri auth sec acct port acct key acct pri acct sec Parameter auth pri jo The IP address of the authentication server auth sec jp The IP address of the alternative authentication server auth port port The UDP port of authentication server s ranging from 1 to 65535 The default value is 1812 acct pri ip The IP address of the accounting server acct sec ip The IP address of the alternative accounting server acct port port The UDP port of accounting server s ranging from 1 to 65535 The default value is 1813 auth key 0 password 7 encrypted password 0 and 7 are the encryption type 0 indicates that an unencrypted password will follow 7 indicates that a symmetric encrypted password with a fixed length will follow By default the encryption type is 0 password is the shared password for the switch and the authentication servers to exchange messages which contains 31 characters 85 at most The question marks and spaces are not allowed encrypted password is a symmetric encrypted password with a fixed length which you can copy from another switch s configuration file The password or encrypted password you configured here will
213. the User The User is classified to the corresponding Group according to its Group Name Security Model and Security Level smode v1 v2c v3 The Security Model of the User with v1 v2c and v3 options By default the option is v1 The Security Model of the User must be the same with that of the Group which the User belongs to slev noAuthNoPriv authNoPriv authPriv The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the option is noAuthNoPriv The Security Level of the User must be the same with that of the Group which the User belongs to cmode none MD5 SHA The Authentication Mode of the SNMP v3 User with none MD5 and SHA options None indicates no authentication method is used MD5 indicates the port authentication is performed via HMAC MD5 algorithm and SHA indicates the port authentication is performed via SHA Secure Hash Algorithm SHA authentication mode has a higher security than MD5 mode By default the Authentication Mode is none confirm pwd Authentication Password ranging from 1 to 16 characters emode none DES The Privacy Mode of the SNMP v3 User with none and DES options None indicates no privacy method is used and DES indicates DES encryption method is used By default the Privacy Mode i
214. the parameters of the ports in different instance IDs as well as view status of the ports in the specified instance Syntax spanning tree mst instance instance id port priority pri cost cost no spanning tree mst instance instance id Parameter instance id Instance ID ranging from 1 to 8 192 pri Port Priority which must be multiple of 16 ranging from O to 240 By default it is 128 Port Priority is an important criterion on determining if the port will be chosen as the root port by the device connected to this port cost Path Cost ranging from O to 200000 The lower value has the higher priority Its default value is O meaning auto Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the priority of port 1 in MST Instance 1 as 64 and path cost as 2000 TL SG3424 config interface gigabitEthernet 1 0 1 TL SG3424 config if spanning tree mst instance 1 port priority 64 cost 2000 spanning tree priority Description The spanning tree priority command is used to configure the bridge priority To return to the default value of bridge priority please use no spanning tree priority command Syntax spanning tree priority pri no spanning tree priority Parameter pri Bridge priority ranging from 0 to 61440 It is 32768 by default Command Mode Global Configuration Mode Example Configure the bridge prior
215. tion The cluster ndp command is used to configure NDP globally To return to the default configuration please use no cluster ndp command NDP Neighbor Discovery Protocol is used to discover the information of the directly connected neighbor devices to support cluster establishing An NDP enabled device sends NDP packets regularly to neighbor devices as well as receives NDP packets from neighbor devices An NDP packet carries the aging time which indicates the period of the receiving devices to keep the NDP packet Syntax cluster ndp cluster ndp timer hello hello time aging aging time 1 no cluster ndp no cluster ndp timer hello hello time aging aging time Parameter hello time Hello Time which is the interval to send NDP packets Hello Time ranges from 5 to 254 in seconds By default it is 60 Hello Time should be smaller than Aging Time aging time Aging Time which is the period for the neighbor switch to keep the NDP packets from this switch Aging Time ranges from 5 to 255 in seconds By default it is 180 Command Mode Global Configuration Mode Example Enable NDP function globally and configure Aging Time as 120 seconds Hello Time as 50 seconds TL SG3424 config cluster ndp 260 TL SG3424 config cluster ndp timer hello 50 aging 120 Change Aging Time to 80 seconds TL SG3424 config cluster ndp timer aging 80 Change Hello Time to 80 seconds TL SG3424 config cluster ndp timer
216. tion Mode 264 Example Display the NTDP configuration globally TL SG3424 show cluster ntdp Display the NTDP configuration of port 2 TL SG3424 show cluster ntdp interface gigabitEthernet 1 0 2 Display the information of device collected through NTDP TL SG3424 show cluster ntdp device list show cluster neighbour Description The show cluster neighbour command is used to display the cluster neighbor information Syntax show cluster neighbour Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the cluster neighbor information TL SG3424 show cluster neighbour show cluster manage role Description The show cluster manage role command is used to display the cluster role of the current switch Syntax show cluster manage role Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the role of the current switch TL SG3424 config show cluster manage role 265
217. tion about the commands used for configuring IEEE 802 1Q VLAN Chapter 4 MAC Based VLAN Commands Provide information about the commands used for configuring MAC Based VLAN Chapter 5 Protocol Based VLAN Commands Provide information about the commands used for configuring Protocol Based VLAN Chapter 6 Voice VLAN Commands Provide information about the commands used for configuring Voice VLAN Chapter 7 GVRP Commands Provide information about the commands used for configuring GVRP GARP VLAN registration protocol Chapter 8 Etherchannel Commands Provide information about the commands used for configuring LAG Link Aggregation Group and LACP Link Aggregation Control Protocol Chapter 9 User Manage Commands Provide information about the commands used for user management Chapter 10 Binding Table Commands Provide information about the commands used for binding the IP address MAC address VLAN and the connected Port number of the Host together Besides it also provide information about the commands used for monitoring the process of the Host obtaining the IP address from DHCP server and record the IP address MAC address VLAN and the connected Port number of the Host for automatic binding Chapter 11 ARP Inspection Commands Provide information about the commands used for protecting the switch from the ARP cheating or ARP Attack Chapter 12 DoS Defend Command Provide information about the commands used for DoS defend
218. tion of the switch Syntax show system time dst Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the DST time information of the switch TL SG3424 show system time dst show system time ntp Description The show system time ntp command is used to display the NTP mode configuration information Syntax show system time ntp Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the NTP mode configuration information of the switch TL SG3424 show system time ntp show system info Description The show system info command is used to display system description system name device location system contact hardware version firmware version system time run time and so on Syntax 124 show system info Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system information TL SG3424 show system info show running config Description The show running config command is used to display the current operating configuration of the system or of a specified port Syntax show running config interface gigabitEthernet port Parameter port The Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system current operating configuration TL SG3424 s how running config show cable diagnostics interface Description The show cable diagnostics interface comman
219. to configure the port for which the ARP Detect function is unnecessary as the Trusted Port To clear the Trusted Port list please use no ip arp detection trust command The specific ports such as up linked port routing port and LAG port should be set as Trusted Port To ensure the normal communication of the switch please configure the ARP Trusted Port before enabling the ARP Detect function Syntax ip arp inspection trust no ip arp inspection trust 72 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the ports 2 5 as the Trusted Port TL SG3424 config interface range gigabitEthernet 1 0 2 5 TL SG3424 config if range ip arp inspection trust ip arp inspection interface Description The ip arp inspection command is used to enable the ARP Defend function To disable the ARP detection function please use no ip arp inspection command ARP Attack flood produces lots of ARP Packets which will occupy the bandwidth and slow the network speed extremely With the ARP Defend enabled the switch can terminate receiving the ARP packets for 300 seconds when the transmission speed of the legal ARP packet on the port exceeds the defined value so as to avoid ARP Attack flood Syntax ip arp inspection no ip arp inspection Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the arp
220. tp Description The system time ntp command is used to configure the time zone and the IP Address for the NTP Server The switch will get UTC automatically if it has connected to an NTP Server Syntax system time ntp fimezone ntp server backup ntp server fetching rate Parameter timezone Your local time zone and it ranges from UTC 12 00 to UTC 13 00 The detailed information that each time zone means are displayed as follow UTC 12 00 TimeZone for International Date Line West 110 UTC 11 00 TimeZone for Coordinated Universal Time 11 UTC 10 00 TimeZone for Hawaii UTC 09 00 TimeZone for Alaska UTC 08 00 TimeZone for Pacific Time US Canada UTC 07 00 TimeZone for Mountain Time US Canada UTC 06 00 TimeZone for Central Time US Canada UTC 05 00 TimeZone for Eastern Time US Canada UTC 04 30 TimeZone for Caracas UTC 04 00 TimeZone for Atlantic Time Canada UTC 03 30 TimeZone for Newfoundland UTC 03 00 TimeZone for Buenos Aires Salvador Brasilia UTC 02 00 TimeZone for Mid Atlantic UTC 01 00 TimeZone for Azores Cape Verde Is UTC TimeZone for Dublin Edinburgh Lisbon London UTC 01 00 TimeZone for Amsterdam Berlin Bern Rome Stockholm Vienna UTC 02 00 TimeZone for Cairo Athens Bucharest Amman Beirut Jerusalem UTC 03 00 TimeZone for Kuwait Riyadh Baghdad
221. try To disable the VLAN IGMP Snooping function please use no ip igmp snooping vlan config command ip igmp snooping vlan config vlan id list rtime router time mtime member time Itime leave time rport interface gigabitEthernet port ip igmp snooping vlan config vian id static ip interface gigabitEthernet port no ip igmp snooping vlan config vian id list no ip igmp snooping vlan config vian id static ip Parameter vlan id list The ID list of the VLAN desired to modify configuration ranging from 1 to 4094 in the format of 1 3 5 router time Router Port Time Within this time if the switch does not receive IGMP query message from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By default it is 300 member time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 leave time Leave Time which is the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 port The Ethernet port number vlan id The VLAN ID of the multicast IP ranging from 1 to 4094 ip The static multicast IP address
222. u set here is allowed to login To cancel the user access limit please use no user access control command Syntax user access control mac based mac addr no user access control Parameter mac addr The source MAC address Only the user with this MAC Address is allowed to login Command Mode Global Configuration Mode Example Configure that only the user whose MAC address is 00 00 13 0A 00 01 is allowed to login TL SG3424 config user access control mac based 00 00 13 0A 00 01 user access control port based Description The user access control port based command is used to limit the ports for login Only the users connected to these ports you set here are allowed to login To cancel the user access limit please use no user access control command 54 Syntax user access control port based interface gigabitEthernet port range gigabitEthernet port list no user access control Parameter port The Ethernet port number port list The list group of Ethernet ports in the format of 1 0 1 4 You can appoint 5 ports at most Command Mode Global Configuration Mode Example Configure that only the users connected to ports 2 6 are allowed to login TL SG3424 config user access control port based interface range gigabitEthernet 1 0 2 6 user max number Description The user max number command is used to configure the maximum login user numbers at the same time To cancel the limit on lo
223. unction for a port With the BPDU protect function enabled the port will set itself automatically as ERROR PORT when it receives BPDU packets and the port will disable the forwarding function for a while To disable the BPDU protect function please use no spanning tree bpduguard command Syntax spanning tree bpduguard no spanning tree bpduguard Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the BPDU protect function for port 2 TL SG3424 config interface gigabitEthernet 2 TL SG3424 config if spanning tree bpduguard spanning tree guard loop Description The spanning tree guard loop command is used to enable the Loop Protect function for a port Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures and network congestions To disable the Loop Protect function please use no spanning tree guard loop command Syntax spanning tree guard loop no spanning tree guard loop Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet 197 Example Enable the Loop Protect function for port 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if spanning tree guard loop spanning tree guard root Description Syntax The spanning tree guard root command is used to enable the Root Protect function for a port With the Root Protect functi
224. unction on interface gigabitEthernet 1 0 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ipv6 mld snooping filter ipv6 mid snooping filter mode Description The ipv6 mld snooping filter mode command is used to configure the filter mode of the interface The default mode is accept To restore the default mode please use no ipv6 mld snooping filter mode command Syntax ipv6 mld snooping filter mode accept refuse no ipv6 mld snooping filter mode Parameter accept Accept the multicast groups within the filter entry refuse Refuse the multicast groups within the filter entry Command Mode Interface Configuration Mode Example Configure the filter mode as refuse on interface gigabitEthernet 1 0 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ipv6 mld snooping filter mode refuse ipv6 mid snooping filter id Description The ipv6 mld snooping filter id command is used to specify the filter id on the interface To disable this configuration please use no ipv6 mld snooping filter id command Syntax ipv6 mld snooping filter id filter list no ipv6 mld snooping filter id Parameter filter list Specify the filter id list in format of 1 3 10 225 Command Mode Interface Configuration Mode Example Specify the filter id as 1 and 10 on interface gigabitEthernet 1 0 2 TL SG3424 config interface gigabitEthernet 1 0 2 TL SG3424 config if ipv
225. unt show ip igmp snooping filter Description The show ip igmp snooping filter command is used to display the Multicast Filter Address table Syntax show ip igmp snooping filter filter addr id list Parameter filter addr id list The multicast ID selected to display the multicast filter address information It is optional Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all the multicast filter address information TL SG3424 config show ip igmp snooping filter 213 Chapter 29 MLD Snooping Commands MLD Snooping Multicast Listener Discovery Snooping is a multicast control mechanism running on Layer 2 switch It can effectively prevent multicast groups being broadcasted in the IPv6 network ipv6 mid snooping Description The ipv6 mld snooping command is used to enable MLD Snooping function globally If this function is disabled all related MLD Snooping function would not work To disable this function please use no ipv6 mld snooping command Syntax ipv6 mld snooping no ipv6 mld snooping Command Mode Global Configuration Mode Example Enable MLD Snooping TL SG3424 config ipv6 mld snooping ipv6 mid snooping router aging time Description The ipv6 mld snooping router aging time command is used to specify router port aging time globally The default aging time is 260 seconds To restore the default timer please use no ipv6 mld snooping router aging time command
226. unters Command Mode Global Configuration Mode Example Clear the statistic information of all ports TL SG3424 config clear counters 139 show interface status Description The show interface status command is used to display the connective status of an Ethernet port Syntax show interface gigabitEthernet port status Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the connective status of all ports TL SG3424 config show interface status Display the connective status of port 1 TL SG3424 config show interface gigabitEthernet 1 0 1 status show interface counters Description The show interface counters command is used to display the statistic information of all ports or an Ethernet port Syntax show interface gigabitEthernet port counters Parameter port The Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the statistic information of all Ethernet ports TL SG3424 config show interface counters Display the statistic information of port 2 TL SG3424 config show interface gigabitEthernet 1 0 2 counters 140 show interface description Description The show interface description command is used to display the description of all ports or an Ethernet port Syntax show interface gigabitEthernet port description Parameter port The Ethernet po
227. ure 1 1 Open Hyper Terminal 3 The Connection Description Window will prompt as Figure 1 2 shown Enter a name into the Name field and click OK Connection Description Y New Connection Enter a name and choose an icon for the connection Name tp link Mss 3eu2 Figure 1 2 Connection Description 4 Select the port to connect in Figure 1 3 and click OK Connect To B tp link Enter details for the phone number that you want to dial Country region United States 1 2 1755 Area code Phone number Connect using E 0M1 Figure 1 3 Select the port to connect 5 Configure the port selected in the step above as the following Figure 1 4 shown Configure Bits per second as 38400 Data bits as 8 Parity as None Stop bits as 1 Flow control as None and then click OK COM1 Properties perrea Port Settings Bits per second Data bits Parity Stop bits Flow control Figure 1 4 Port Settings 6 The DOS prompt TL SG3424 gt will appear after pressing the Enter button as Figure 1 5 shown It indicates that you can use the CLI now e tp link HyperTerminal TL SG3424 gt Connected 0 00 32 Auto detect Auto detect Figure 1 5 Log in the Switch 1 1 2 Configuring the Privileged EXEC Mode Password To configure the switch remotely by a Telnet or SSH connection please set a password for entering the Privileged EXEC Mode through the console connection f
228. use no lldp med fast count command Syntax lldp med fast count count no lldp med fast count Parameter count Configure the Fast Start Count parameter It ranges from 1 to 10 By default it is 4 Command Mode Global Configuration Mode Example Specify Fast Start Count as 5 TL SG3424P config Ildp med fast count 5 Ildp receive Description The lldp receive command is used to enable the designated port to receive LLDPDU To disable the function please use no Ildp receive command 252 Syntax lldp receive no lldp receive Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable port 1 to receive LLDPDU TL SG3424P config interface gigabitEthernet 1 0 1 TL SG3424P config if lldp receive Ildp transmit Description The lldp transmit command is used to enable the designated port to transmit LLDPDU To disable the function please use no Ildp transmit command Syntax lldp transmit no lldp transmit Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable port 1 to transmit LLDPDU TL SG3424P config interface gigabitEthernet 1 0 1 TL SG3424P config if lldp transmit Ildp snmp trap Description The Ildp snmp trap command is used to enable the port s SNMP notification If enabled the port will notify the trap event to network management system To disabl
229. value of a monitored variable exceeds the threshold an alarm event is generated which triggers the switch to act in the set way Syntax rmon alarm index interface gigabitEthernet port alarm variable drop revbyte revpkt bpkt mpkt crc lign undersize oversize fragment jabber collision 64 65 127 128 511 512 1023 1024 10240 s type absolute delta rising threshold r hold rising event index r event falling threshold 243 f hold falling event index f event a type rise fall all owner owner name interval interval no rmon alarm index Parameter index The index number of the Alarm Management entry ranging from 1 to 12 in the format of 1 3 5 port The Ethernet port number alarm variable The alarm variable By default the option is drop s type Sample Type which is the sampling method for the selected variable and comparing the value against the thresholds There are two options absolute and delta Absolute indicates comparing the values directly with the thresholds at the end of the sampling interval Delta indicates subtracting the last sampled value from the current value and then comparing the difference in the values with the threshold By default the Sample Type is absolute r hold The rising counter value that triggers the Rising Threshold alarm ranging from 1 to 65535 By default itis 100 r event
230. x shutdown no shutdown 133 Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Disable port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if shutdown flow control Description The flow control command is used to enable the flow control function for a port To disable the flow control function for this corresponding port please use no flow control command With the flow control function enabled the Ingress Rate and Egress Rate can be synchronized to avoid packet loss in the network Syntax flow control no flow control Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable the flow control function for port 3 TL SG3424 config interface gigabitEthernet 1 0 3 TL SG3424 config if flow control media type Auer This command does not apply to TL SG3210 Description The media type command is used to configure the media type of Combo port For a Combo port the media type should be configured before you set its speed and mode 134 Syntax media type rj45 sfp Parameter rj45 sfp Media type Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the media type of Combo port 24T as SFP TL SG3424 config interface gigabitEthernet 1 0 24 TL SG3424 config if
231. x global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of 801 X globally TL SG3424 config show dot1x global show dot1x interface Description The show dot1x interface command is used to display all ports or the specified port s configuration information of 801 X Syntax show dot1x interface gigabitEthernet port Parameter port The number of the Ethernet port Display the configuration of all the ports by default Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of 801 X for all ports TL SG3424 config show dot1x interface Display the configuration information of 801 X for port 1 TL SG3424 config show dot1x interface gigabitEthernet 1 0 1 87 show radius accounting Description The show radius accounting command is used to display the configuration of the accounting server Syntax show radius accounting Command Mode Privileged EXEC Mode and Any Configuration Modes Example Display the configuration of the accounting server TL SG3424 config show radius accounting show radius authentication Description The show radius authentication command is used to display the configuration of the RADIUS authentication server Syntax show radius authentication Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the RADIUS authentication
232. xample 192 168 0 100 or fe80 1234 n count The amount of times to send test data during Ping testing It ranges from 1 to 10 By default this value is 4 count The size of the sending data during ping testing It ranges from 1 to 1024 bytes By default this value is 64 i count The interval to send ICMP request packets It ranges from 100 to 1000 milliseconds By default this value is 1000 Command Mode User EXEC Mode and Privileged EXEC Mode Example To test the connectivity between the switch and the network device with the IP 192 168 0 131 please specify the count l as 512 bytes and count i as 1000 milliseconds If there is not any response after 8 times Ping test the connection between the switch and the network device is failed to establish TL SG3424 ping 192 168 0 131 n 8 1 512 To test the connectivity between the switch and the network device with the IP fe80 1234 please specify the count l as 512 bytes and count i as 1000 milliseconds If there is not any response after 8 times Ping test the connection between the switch and the network device is failed to establish TL SG3424 ping fe80 1234 n 8 1 512 tracert Description The tracert command is used to test the connectivity of the gateways during its journey from the source to destination of the test data Syntax tracert ip ipv6 ip_addr maxHops 122 Parameter ip The type of the IP addr
233. y the switch s SNMP agent Command Mode Global Configuration mode Example Add a group and configure the name as group 1 the Security Model as SNMP v3 the security level as authNoPriv the management access to the assigned View viewDefault as read write besides the notification messages sent by View viewDefault can be received by Management station TL SG3424 config snmp server group group1 smode v3 slev authNoPriv read viewDefault write viewDefault notify viewDefault Delete group 1 TL SG3424 config no snmp server group group1 smode v3 slev authNoPriv snmp server user Description The snmp server user command is used to add User To delete the corresponding User please use no snmp server user command The User in an SNMP Group can manage the switch via the management station software The User and its Group have the same security level and access right Syntax snmp server user name local remote group name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv cmode none MD5 SHA cpwd confirm pwd emode none DES H epwd encrypt pwd no snmp server user name Parameter name User Name ranging from 1 to 16 characters 233 local remote User Type with local and remote options Local indicates that the user is connected to a local SNMP engine while remote means that the user is connected to a remote SNMP engine group name The Group Name of
234. ypted to access Privileged EXEC Mode from User EXEC Mode The password will be displayed in the encrypted form TL SG3424 config enable secret 0 admin 22 disable Description The disable command is used to return to User EXEC Mode from Privileged EXEC Mode Syntax disable Command Mode Privileged EXEC Mode Example Return to User EXEC Mode from Privileged EXEC Mode TL SG3424 disable TL SG3424 gt configure Description The configure command is used to access Global Configuration Mode from Privileged EXEC Mode Syntax configure Command Mode Privileged EXEC Mode Example Access Global Configuration Mode from Privileged EXEC Mode TL SG3424 configure TL SG3424 config exit Description The exit command is used to return to the previous Mode from the current Mode Syntax exit 23 Command Mode Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode and then return to Privileged EXEC Mode TL SG3424 config if exit TL SG3424 config exit TL SG3424 end Description The end command is used to return to Privileged EXEC Mode Syntax end Command Mode Any Configuration Mode Example Return to Privileged EXEC Mode from Interface Configuration Mode TL SG3424 config if end TL SG3424 history Description The history command is used to show the latest 20 commands you entered in the current mode since the

TP-Link TL-SG3210 V2 CLI Reference Guide

Contents

Download Pdf Manuals

Related Search

Related Contents