Home

TP-Link 150Mbs User's Manual

1. User Name username password wsssssee Connect Aesconnect Disconnected Dynamic IP Static IP Server IP Address Name j y IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Gateway 0 0 0 0 DNS 0 0 0 0 0 0 0 0 Internet IP Address 0 0 0 0 Internet DNS 0 0 0 0 0 0 0 0 MTU Size in bytes 1420 The defaultis 1420 do not change unless necessary R E Max dle Time 115 minutes 0 means remain active at all times WAN Connection Mode Connect on Demand O Connect Automatically Connect Manually Save Figure 4 13 WAN PPTP gt User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive gt Dynamic IP Static IP Choose either as you are given by your ISP and enter the ISP s IP address or the domain name 27 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router If you choose static IP and enter the domain name you should also enter the DNS assigned by your ISP And click the Save button Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately gt Connect on Demand You can configure the Router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time If your Internet connection has been terminated due to inactivity Connect on Demand enables the Router to automatically re establish your connection as soo
2. 4 8 Forwarding Forwarding Port Triggering DMZ UPnP Figure 4 30 The Forwarding menu There are four submenus under the Forwarding menu shown in Figure 4 30 Virtual Servers Port Triggering DMZ and UPnP Click any of them and you will be able to configure the corresponding function 4 8 1 Virtual Servers Choose menu Forwarding Virtual Servers and then you can view and add virtual servers in the next screen shown in Figure 4 31 Virtual servers can be used for setting up public services on your LAN A virtual server is defined as a service port and all requests from Internet to this service port will be redirected to the computer specified by the server IP Any PC that was used for a virtual server must have a static or reserved IP address because its IP address may change when using the DHCP function Virtual Servers ID Service Ports IP Address Protocol Add Mew Figure 4 31 Virtual Servers gt Service Ports The numbers of External Service Ports You can enter a service port or a range of service ports the format is XXX YYY XXX is the Start port and YYY is the End port gt IP Address The IP address of the PC running the service application gt Protocol The protocol used for this application either TCP UDP or All all protocols supported by the Router gt Status The status of this entry Enabled means the virtual server entry is enabled 43 TL WR720N 150Mbps W
3. DNS servers are set up improperly You should contact your ISP to get DNS server addresses 20 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router gt Get IP with Unicast DHCP A few ISPs DHCP servers do not support the broadcast applications If you cannot get the IP Address normally you can choose this option It is rarely required 2 If your ISP provides a static or fixed IP Address Subnet Mask Gateway and DNS setting select Static IP The Static IP settings page will appear as shown in Figure 4 8 WAN WAN Connection Type Static IP v IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 Optional MTU Size in bytes 1500 The defaultis 1500 do not change unless necessary Primary DNS 0 0 0 0 Optional secondary DNS 000 0 Optional Save Figure 4 8 WAN Static IP gt IP Address Enter the IP address in dotted decimal notation provided by your ISP gt Subnet Mask Enter the subnet Mask provided by your ISP in dotted decimal notation Usually the Sub Mask is 255 255 255 0 gt Default Gateway Optional Enter the gateway IP address provided by your ISP in dotted decimal notation gt MTU Size The normal MTU Maximum Transmission Unit value for most Ethernet networks is 1500 Bytes It is not recommended that you change the default MTU Size unless required by your ISP gt Primary Secondary DNS Optional Enter one or two DNS addresses in dotted de
4. E Note Your opposite side should call your WAN IP which is displayed on the Status page 4 How to enable DMZ Host Log in to the Router click the Forwarding menu on the left of your browser and click DMZ submenu On the DMZ page click Enable radio button and type your IP address into the DMZ Host IP Address field using 192 168 0 169 as an example remember to click the Save button Current DMZ Status Enable Disable DMZ Host IP Address 192 168 1 100 Figure A 6 DMZ 4 Iwant to build a WEB Server on the LAN what should do 1 Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router you must change the WEB management port number to avoid interference 7 2 To change the WEB management port number Log in to the Router click the Security menu on the left of your browser and click Remote Management submenu On the Remote Management page type a port number except 80 such as 88 into the Web Management Port field Click Save and reboot the Router 93 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Remote Management Web Management Port Remote Management IP Address 0 0 0 0 Enter 255 255 255 255 for alli Saye Figure A 7 Remote Management Note If the above configuration takes effect you can visit and configure the Router by typing http 192 168 0 1 88 the Router s LAN IP address Web Management
5. Slow Flash A wireless device is connecting to the network by WPS function This process will last in the first 2 minutes A wes on A wireless device has been successfully added to the on Awe by WPS function A wireless device failed to be added to the network by Quick Flash WPS function Table 1 1 The LEDs description Note After a device is successfully added to the network by WPS function the WPS LED will keep on for about 5 minutes and then turn off 4 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 1 4 2 The Rear Panel Figure 1 2 Rear Panel sketch The following parts are located on the rear panel View from left to right gt WPS RESET This button is used for both WPS and Reset function To use the WPS function press it for less than five seconds to use the RESET function press it for more than five seconds Used as RESET button There are two ways to reset to the Router s factory defaults 1 Use the Factory Defaults function on System Tools gt Factory Defaults page in the Router s Web based Utility 2 Use the Factory Default Reset button With the Router powered on press and hold the RESET button at least 5 seconds until the SYS LED becomes quick flash from slow flash Then release the button and wait the Router to reboot to its factory default settings e Used as WPS button WPS If you have client devices such as wireless adapters that support Wi Fi Protec
6. 1 Click the Enable button to enable this function 2 Select the radio button Deny the stations not specified by any enabled entries in the list to access for Filtering Rules 3 Delete all or disable all entries if there are any entries already 4 Click the Add New button and enter the MAC address 00 0A EB 00 07 8A 00 OA EB 00 23 11 in the MAC Address field then enter wireless station A B in the Description field while select Enabled in the Status drop down list Finally click the Save and the Back button The filtering rules that configured should be similar to the following list Filtering Rules Allow the stations not specified by any enabled entries in the listto access Deny the stations not specified by any enabled entries in the listto access D MAC Address Status Description Modify 1 00 04 EB 00 07 8A Enabled wireless station A Modify Delete E 00 04 EB 00 43 11 Enabled wireless station E Modify Delete 27 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 6 4 Wireless Advanced Choose menu Wireless Wireless Advanced and then you can configure the advanced settings of your wireless network Wireless Advanced Transmit Power High we Beacon Interval 100 40 1000 RTS Threshold 2346 1 2346 Fragmentation Threshold 2506 2346 DTIM Interval 1 1 255 Enable vii Enable Short Gl Enable AP Isolation Figure 4 23 Wireless Advanced gt Transmit Power H
7. 299255 2590 Default Gateway 192 168 1 1 DNS Server 192 168 1 1 0 0 0 0 Traffic Statistics Received Bytes 3918 Packets 28 System Up Time O days 02 23 02 Figure 4 1 Router Status 4 3 Quick Setup Please refer to Section 3 2 Quick Installation Guide 44 WPS This section will guide you to add a new wireless device to an existing network quickly by WPS Wi Fi Protected Setup function a Choose menu WPS and you will see the next screen shown in Figure 4 2 16 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Current SSID TP LINK ES3C560 WPS Status Enabled Disable WPS Current PIN 12345670 Restore PIN Gen New PIN Add anew device Add device Figure 4 2 WPS gt Current SSID The router supports multi SSID and you can choose one SSID which you want to configure its WPS function from the drop down list For example if your wireless client wants to connect to one of the router s SSID TP LINK_E3C860 by WPS you should select TP LINK_E3C860 as Current SSID gt WPS Status Enable or disable the WPS function here gt Current PIN The current value of the Router s PIN is displayed here The default PIN of the Router can be found in the label or User Guide gt Restore PIN Restore the PIN of the Router to its default gt Gen New PIN Click this button and then you can get a new random value for the Router s PIN You can ensure the network s
8. Target Here displays the target selected in the corresponding rule 61 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router gt Schedule Here displays the schedule selected in the corresponding rule Vv Enable Here displays the status of the rule enabled or not Check this option to enable a specific entry Modify Here you can edit or delete an existing rule Setup Wizard Click the Setup Wizard button to create a new rule entry Add New Click the Add New button to add a new rule entry Enable All Click the Enable All button to enable all the rules in the list Disable All Click the Disable All button to disable all the rules in the list Delete All Click the Delete All button to delete all the entries in the table Vv Vv Y Y VY V WV Move You can change the entry s order as desired Enter in the first box the ID number of the entry you want to move and in the second box another ID number and then click the Move button to change the entries order gt Next Click the Next button to go to the next page gt Previous Click the Previous button to return to the previous page There are two methods to add a new rule Method One 1 Click Setup Wizard button and the next screen will appear as shown in Figure 4 54 Quick Setup Create a Host Entry Mode IP Address w 0 i ee Figure 4 54 Quick Setup Create a Host Entry gt Host Description In this field create a
9. e Radius Port Enter the port that radius service used e Radius Password Enter the password for the Radius Server e Group Key Update Period Specify the group key update interval in seconds The value should be 30 or above Enter 0 to disable the update gt WPA PSK WPA2 PSK It s the WPA WPA2 authentication type based on pre shared passphrase Version you can choose the version of the WPA PSK security on the drop down list The default setting is Automatic which can select WPA PSK Pre shared key of WPA or WPA2 PSK Pre shared key of WPA automatically based on the wireless station s capability and request Encryption When WPA PSK or WPA is set as the Authentication Type you can select either Automatic or TKIP or AES as Encryption Note If you check the WPA PSK WPA2 PSK radio button and choose TKIP encryption you will find a notice in red as shown in Figure 4 20 WPA PSK WPA2 PSK Version Encryption fou can enter ASCII characters between 8 and 63 or Hexadecimal characters between 8 and 64 Group Key Update Period 386400 fin second minimum is 30 0 means no update We do not recommend using the TRIP encryption ifthe device operates in 2802 11n mode due to the factthat TKIP is not supported by 602 11n specification Figure 4 20 e PSK Password You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters e Group Key Update Period Specify the group key update
10. gt Mode There are two types of mode Minimum Bandwidth Guarantee and Maximum Bandwidth Limit gt Bandwidth The bandwidth you supply to this entry gt Description The description for this entry 73 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Click Enable to enable this entry Click the Clear button to clear a single entry Click the Clear All button to clear all entries Click the Save button to save all configurations cs Note The conversion relation of bandwidth 1Mbps 1000Kbps 2 Please choose the Network Connection Type and set the bandwidth according to your Network If you are not clear about that please contact with your ISP for help If no IP QoS item is enabled the Bandwidth Apply won t be effective IP address range for different entries could not have intersection with each other After the configurations click the Save button for the change to take effect 4 14 IP amp MAC Binding IP amp MAC Binding Figure 4 70 the IP amp MAC Binding menu There are two submenus under the IP amp MAC Binding menu shown in Figure 4 70 Binding Settings and ARP List Click any of them and you will be able to scan or configure the corresponding function The detailed explanations for each submenu are provided below 4 14 1 Binding Settings This page displays the IP amp MAC Binding Setting table you can operate it in accord with your desire shown in Figure 4 71 Binding S
11. make sure your PC is connected to the Internet through the broadband service successfully If there is any problem please contact your ISP After that please install the Router according to the following steps Don t forget to pull out the power plug and keep your hands dry 1 Power off your PC Cable DSL Modem and the Router 2 Locate an optimum location for the Router The best place is usually at the center of your wireless network The place must accord with the Installation Environment Requirements 3 Connect the PC s and each Switch Hub in your LAN to the LAN Ports on the Router shown in Figure 2 1 If you have the wireless NIC and want to use the wireless function you can skip this step 4 Connect the DSL Cable Modem to the WAN port on the Router shown in Figure 2 1 5 Connect the power adapter to the power socket on the Router and the other end into an electrical outlet The Router will start to work automatically Qs TL WR720N METER EEE oleh tele 6 Power on your PC and Cable DSL Modem RESET POWER WAN 1 2 Figure 2 1 Hardware Installation of the 150Mbps Wireless N Router ay E TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Chapter 3 Quick Installation Guide This chapter will show you how to configure the basic functions of your 150Mbps Wireless N Router using Quick Setup Wizard within minutes 3 1 TCP IP Configuration The default domain name of the 150Mbps
12. zero key is not promoted or 5 ASCII characters 128 bit You can enter 26 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 13 ASCII characters 152 bit You can enter 32 hexadecimal digits any combination of 0 9 a f A F zero key is not promoted or 16 ASCII characters Note If you do not set the key the wireless security function is still disabled even if you have selected Shared Key as Authentication Type gt WPA WPAZ2 It s based on Radius Server e Version you can choose the version of the WPA security on the drop down list The default setting is Automatic which can select WPA Wi Fi Protected Access or WPA2 WPA version 2 automatically based on the wireless station s capability and request e Encryption You can select either Automatic or TKIP or AES E Note If you check the WPA WPA2 radio button and choose TKIP encryption you will find a notice in red as shown in Figure 4 19 Version Encryption TKIP e Radius Serveri Radius Port 1812 1 65535 0 stands for default port 1812 Group Key Update Period jo fin second minimum is 30 0 means no update We do not recommend using the TKIP encryption ifthe device operates in 2802 11 mode due to the factihat TKIP is not supported by Draft 11N specification Figure 4 19 34 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router e Radius Server IP Enter the IP address of the Radius Server
13. 2 The WPS function cannot be configured if the Wireless Function of the Router is disabled Please make sure the Wireless Function is enabled before configuring the WPS 4 5 Network WAN MAC Clone Figure 4 5 the Network menu There are three submenus under the Network menu shown in Figure 4 5 LAN WAN and MAC Clone Click any of them and you will be able to configure the corresponding function 4 5 1 LAN Choose menu Network LAN and then you can configure the IP parameters of the LAN on the screen as below MAC Address 00 08 01 00 00 04 IP Address 192 166 0 1 subnet Mask 255 255 255 0 A Save Figure 4 6 LAN gt MAC Address The physical address of the Router as seen from the LAN The value can t be changed gt IP Address Enter the IP address of your Router or reset it in dotted decimal notation factory default 192 168 0 1 gt Subnet Mask An address code that determines the size of the network Normally use 255 255 255 0 as the subnet mask E Note If you change the IP Address of LAN you must use the new IP Address to login the Router 2 Ifthe new LAN IP Address you set is not in the same subnet the IP Address pool of the DHCP server will change accordingly at the same time while the Virtual Server and DMZ Host will not take effect until they are re configured 19 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 5 2 WAN Choose menu Network
14. Enable Domain Filtering have been selected on the Firewall page To Add a Domain filtering entry click the Add New button The page Add or Modify a Domain Filtering Entry will appear shown in Figure 4 42 Add or Modify an Domain Filtering Entry Effective Time y Status Enabled we Figure 4 42 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry follow these instructions 1 Effective Time Enter a range of time in HHMM format specifying the time for the entry to take effect For example if you enter 0803 1705 than the entry will take effect from 08 03 to 17 05 2 Domain Name Type the domain or key word as desired in the field A blank in the domain field means all websites on the Internet For example www xxyy com cn net 3 Select Enabled or Disabled for this entry on the Status pull down list 4 Click the Save button to save this entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 2 Modify the information 3 Click the Save button Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled 52 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Click the Delete All button to delete all entries Click the Next button to go to the next page and the Previous button to return to the previous page For
15. For example 192 168 0 20 192 168 0 30 Keep the field open which means all LAN IP Addresses have been put into the field 50 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 3 LAN Port Enter a LAN Port or a range of LAN ports in the field For example 1030 2000 Keep the field open which means all LAN ports have been put into the field 4 WAN IP Address Enter a WAN IP Address or a range of WAN IP Addresses in the field in dotted decimal notation format For example 61 145 238 6 61 145 238 47 Keep the field open which means all WAN IP Addresses have been put into the field 5 WAN Port Enter a WAN Port or a range of WAN Ports in the field For example 25 110 Keep the field open which means all WAN Ports have been put into the field 6 Protocol Select which protocol is to be used either TCP UDP or All all protocols supported by the router 7 Action Select either Allow or Deny through the router 8 Status Select Enabled or Disabled for this entry on the Status pull down list 9 Click the Save button to save this entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 2 Modify the information 3 Click the Save button Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled Click the Delete All button to delete all entr
16. PSK WPA2 WPA2 PSK AP UP AP DOWN Disconnected gt Received Packets Packets received by the station gt Sent Packets Packets sent by the station You cannot change any of the values on this page To update this page and to show the current connected wireless stations click on the Refresh button If the numbers of connected wireless stations go beyond one page click the Next button to go to the next page and click the Previous button to return to the previous page 39 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Note This page will be refreshed automatically every 5 seconds 4 7 DHCP DHCP DHCP Clients List Address Reservation Figure 4 25 The DHCP menu There are three submenus under the DHCP menu shown in Figure 4 25 DHCP Settings DHCP Clients List and Address Reservation Click any of them and you will be able to configure the corresponding function 4 7 1 DHCP Settings Choose menu DHCP DHCP Settings and then you can configure the DHCP Server on the page shown in Figure 4 26 The Router is set up by default as a DHCP Dynamic Host Configuration Protocol server which provides the TCP IP configuration for all the PC s that are connected to the Router on the LAN DHCP Settings DHCP Server O Disable Enable Start IP Address End IP Address Address Lease Time minutes 1 2880 minutes the default value is 120 Default Gateway optional Default D
17. The default value is 1 which indicates the DTIM Interval is the same as Beacon Interval gt Enable WMM WMM function can guarantee the packets with high priority messages being transmitted preferentially It is strongly recommended enabled gt Enable Short Gl This function is recommended for it will increase the data capacity by reducing the guard interval time gt Enabled AP Isolation This function can isolate wireless stations on your network from each other Wireless devices will be able to communicate with the Router but not with each other To use this function check this box AP Isolation is disabled by default E Note If you are not familiar with the setting items in this page it s strongly recommended to keep the provided default values otherwise it may result in lower wireless network performance 4 6 5 Wireless Statistics Choose menu Wireless Wireless Statistics and then you can see the MAC Address Current Status Received Packets and Sent Packets for each connected wireless station Wireless Statistics Current Connected Wireless Stations numbers 1 ID MAC Address Current Status Recerved Packets sent Packets 1 00 04 EB 88 34 75 STA A5S5OC 416 2 Figure 4 24 The Router attached wireless stations gt MAC Address The connected wireless station s MAC address gt Current Status The connected wireless station s running status one of STA AUTH STA ASSOC STA JOINED WPA WPA
18. and then you can configure the management rule in the screen as shown in Figure 4 45 The management feature allows you to deny computers in LAN from accessing the Router 54 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Local Management Management Rules Allthe PCs on the LAN are allowed to access the Routers Web Based Utility O Only the PCs listed can browse the builtin web pages to perform Administrator tasks MAC 1 MAC 2 MAC 3 MAC 4 Your PC s MAC Address Figure 4 45 Local Management By default the radio button All the PCs on the LAN are allowed to access the Router s Web Based Utility is checked If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router s Web Based Utility locally from inside the network check the radio button Only the PCs listed can browse the built in web pages to perform Administrator tasks and then enter each MAC Address in a separate field The format for the MAC Address is XX XX XX XX XX XX X is any hexadecimal digit Only the PCs with MAC address listed can use the password to browse the built in web pages to perform Administrator tasks while all the others will be blocked After click the Add button your PC s MAC Address will be placed in the list above Click the Save button to save your settings E Note If your PC is blocked but you want to access the Router again use a pin to press and hold the WPS RESET but
19. click the Save button It will take effect after rebooting MAC Clone WAN MAC Address 00 08 01 00 00 05 E Your PC s MAC Address 00 19 66 80 54 28 Clone MAC Address Figure A 3 MAC Clone 3 Iwantto use Netmeeting what do need to do 1 If you start Netmeeting as a host you don t need to do anything with the Router 2 If you start as a response you need to configure Virtual Server or DMZ Host and make sure the H323 ALG is enabled 3 How to configure Virtual Server Log in to the Router click the Forwarding menu on the left of your browser and click Virtual Servers submenu On the Virtual Servers page click Add New Then on the Add or Modify a Virtual Server Entry page enter 1720 for the Service Port blank and your IP address for the IP Address blank taking 192 168 0 169 for an example remember to Enable and Save Virtual Servers ID Service Port Internal Port IP Address Protocol Status Modify 1 1720 1720 192 168 0 169 ALL Enabled Modify Delete Add New Enable All Disable All Delete All Figure A 4 Virtual Servers 92 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Add or Modify a Virtual Server Entry Service Port COOL or XX Internal Port O Only valid for single Service Port or leave a blank IP Address Protocol lL M ll Status Enabled we Common Service Port Select One e Figure A 5 Add or Modify a Virtual server Entry
20. interval in seconds The value should be 30 or above Enter 0 to disable the update Be sure to click the Save button to save your settings on this page 4 6 3 Wireless MAC Filtering Choose menu Wireless MAC Filtering and then you can control the wireless access by configuring the Wireless MAC Address Filtering function shown in Figure 4 21 35 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Wireless MAC Filtering Current SSID TP LINK_ESCoB0 w Wireless MAC Filtering Enabled Filtering Rules O Allow the stations not specified by any enabled entries in the listto access Deny the stations not specified by any enabled entries in the listto access D MAC Address Status Description Modify 1 00 04 EB 00 07 8A Enabled wireless station A Modify Delete E 00 04 EB 00 23 11 Enabled wireless station B Modify Delete Add New Enable All Disable All Delete All Figure 4 21 Wireless MAC address Filtering To filter wireless users by MAC Address click Enable The default setting is Disabled gt MAC Address The wireless station s MAC address that you want to filter gt Status The status of this entry either Enabled or Disabled gt Description A simple description of the wireless station To Add a Wireless MAC Address filtering entry click the Add New button The Add or Modify Wireless MAC Address Filtering entry page will appear as shown in Figure 4 22 Add or Modify Wireless MAC Addre
21. of the Router system will reboot automatically e Restore the Router s settings to factory defaults system will reboot automatically e Update the configuration with the file system will reboot automatically 85 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 16 7 Password Choose menu System Tools Password and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 4 87 Password Old User Hame Old Password New User Name New Password Confirm New Password Clear All Figure 4 87 Password It is strongly recommended that you should change the factory default user name and password of the Router because all users who try to access the Router s Web based utility or Quick Setup will be prompted for the Router s default user name and password Note The new user name and password must not exceed 14 characters in length and not include any spaces Enter the new Password twice to confirm it Click the Save button when finished Click the Clear All button to clear all 4 16 8 System Log Choose menu System Tools System Log and then you can view the logs of the Router 86 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router System Log Auto Mail Feature Disabled Mail Settings Mail Log Index Level 11 10 INFO INFO INFO INFO INFO INFO INFO INFO INFO INFO Log C
22. or Disable button This feature is enabled by default gt Current UPnP Settings List This table displays the current UPnP information App Description The description about the application which initiates the UPnP request External Port The port which the Router opened for the application e Protocol The type of protocol which is opened e Internal Port The port which the Router opened for local host e IP Address The IP address of the local host which initiates the UPnP request e Status Either Enabled or Disabled Enabled means that the port is still active otherwise the port is inactive Click the Enable button to enable UPnP Click the Disable button to disable UPnP Click the Refresh button to update the Current UPnP Settings List 48 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 9 Security Security IP Address Filtering Domain Filtering MAC Address Filtering Local Management Remote Management Advanced Security Figure 4 37 The Security menu There are seven submenus under the Security menu as shown in Figure 4 37 Firewall IP Address Filtering Domain Filtering MAC Address Filtering Local Management Remote Management and Advanced Security Click any of them and you will be able to configure the corresponding function 4 9 1 Firewall Using the Firewall page you can turn the general firewall switch on or off The default setting for the switch is off
23. the table There would be 5 entries on each page Click Previous to return to the previous page and Next to the next page 90 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Appendix A FAQ 1 How do configure the Router to access Internet by ADSL users 1 First configure the ADSL Modem configured in RFC1483 bridge model 2 Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router The telephone cord plugs into the Line port of the ADSL Modem 3 Login to the Router click the Network menu on the left of your browser and click WAN submenu On the WAN page select PPPoE Russia PPPoE for WAN Connection Type Type user name in the User Name field and password in the Password field type password in the Confirm Password field again finish by clicking Connect WAN Connection Type PPPoE Russia PPPoE PPPoE Connection User Name username Password PPP Confirm Password EITITITI Figure A 1 PPPoE Connection Type 4 If your ADSL lease is in pay according time mode select Connect on Demand or Connect Manually for Internet connection mode Type an appropriate number for Max Idle Time to avoid wasting paid time Otherwise you can select Auto connecting for Internet connection mode Wan Connection Mode Connect on Demand hax Idle Time minutes 0 means remain active at all times Connect A
24. to 32 characters The same name SSID must be assigned to all wireless devices in your network Check the Enable box to enable the desired SSID The wireless stations connected to different SSIDs can not communicate with each other Cc Note Multiple SSIDs can be set up in public places like coffee house for guests to allow virtual segregation stations which share the same channel gt Region Select your region from the drop down list This field specifies the region where the wireless function of the Router can be used It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field If your country or region is not listed please contact your local government agency for assistance When you select your local region from the drop down list click the Save button and then the Note Dialog will appear Click OK 30 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Microsoft Internet Explorer Note Dialog Note Limited by local law regulations version for North America does not have region selection option gt Channel This field determines which operating frequency will be used The default channel is set to Auto so the AP will choose the best channel automatically It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point gt Mode Select the desired mode The d
25. to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page For example If you desire that the child PC with MAC address 00 11 22 33 44 AA can access www google com on Saturday only while the parent PC with MAC address 00 11 22 33 44 BB is without any restriction you should follow the settings below 1 Click Parental Control menu on the left to enter the Parental Control Settings page Check Enable and enter the MAC address 00 11 22 33 44 BB in the MAC Address of Parental PC field 2 Click Access Control Schedule on the left to enter the Schedule Settings page Click Add New button to create a new schedule with Schedule Description is Schedule_1 Day is Sat and Time is all day 24 hours 3 Click Parental Control menu on the left to go back to the Add or Modify Parental Control Entry page _ Click Add New button Enter 00 11 22 33 44 AA in the MAC Address of Child PC field Sh O N Enter www google com in the Allowed Domain Name field O1 Enter Allow Google in the Website Description field Select Schedule_1 you create just now from the Effective Time drop down list 6 In Status field select Enable 4 Click Save to complete the settings Then you will go back to the Parental Control Settings page and see the following list as shown in Figure 4 51 60 TL W
26. unique description for the host e g Host_1 gt Mode Here are two options IP Address and MAC Address You can select either of them from the drop down list If the IP Address is selected you can see the following item gt LAN IP Address Enter the IP address or address range of the host in dotted decimal format e g 192 168 0 23 If the MAC Address is selected you can see the following item 62 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router gt MAC Address Enter the MAC address of the host in XX XX XX XX XX XX format e g 00 11 22 33 44 AA 2 Click Next when finishing creating the host entry and the next screen will appear as shown in Figure 4 55 Quick Setup Create an Access Target Entry Mode IF Address a Target Description IP Address Target Port Protocol Common Service Port please select Y Figure 4 55 Quick Setup Create an Access Target Entry gt Target Description In this field create a description for the target Note that this description should be unique e g Target_1 gt Mode Here are two options IP Address and Domain Name You can choose either of them from the drop down list If the IP Address is selected you will see the following items gt IP Address Enter the IP address or address range of the target targets in dotted decimal format e g 192 168 0 23 gt Target Port Specify the port or port range for the tar
27. unless the new firmware has a new feature you want to use However when experiencing problems caused by the Router rather than the configuration you can try to upgrade the firmware When you upgrade the Router s firmware you may lose its current configurations so before upgrading the firmware please write down some of your customized settings to avoid losing important settings Do not turn off the Router or press the Reset button while the firmware is being upgraded Loss of power during the upgrade could damage the Router The firmware version must correspond to the hardware The upgrade process takes a few moments and the Router restarts automatically when the upgrade is complete 4 16 4 Factory Defaults Choose menu System Tools Factory Defaults and then and you can restore the configurations of the Router to factory defaults on the following screen Factory Defaults Click the following button to reset all configuration settings to their default values Figure 4 84 Restore Factory Default Click the Restore button to reset all configuration settings to their default values e The default User Name admin e The default Password admin e The default IP Address 192 168 0 1 e The default Subnet Mask 255 255 255 0 Note All changed settings will be lost when defaults are restored 4 16 5 Backup amp Restore Choose menu System Tools Backup 8 Restore and then you can save the current
28. your Router The quick setup will tell you how to configure the basic network parameters To continue please click the Next button To exit please click the Exit button Figure 3 5 Quick Setup 3 Click Next and then WAN Connection Type page will appear as shown in Figure 3 6 10 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Quick Setup WAN Connection Type The Quick Setup is preparing to set Up your connection type of VWwAN port The Router will try to detect the Internet connection type your ISF provides ifyou select the Auto Detect option Otherwise you need to specify the connection type manually Auto Detect Let the Router automatically detect the connection type your ISP provides PPPoE For this connection your will need your account name and password for your ISP Dynamic IP Your ISF uses a DHCP service to assign your Router an IP address when connecting to the Internet Static IP This type of connetetion uses a permanent fixed static IP address that your ISP assigned Figure 3 6 Choose WAN Connection Type The Router provides Auto Detect function and supports three popular ways PPPoE Dynamic IP and Static IP to connect to the Internet It s recommended that you make use of the Auto Detect function If you are sure of what kind of connection type your ISP provides you can select the very type and click Next to go on configuring 4 If you select Auto Detect
29. 3 8 Quick Setup Static IP gt IP Address This is the WAN IP address seen by external users on the Internet including your ISP Enter the IP address into the field gt Subnet Mask The Subnet Mask is used for the WAN IP address it is usually 255 255 255 0 gt Default Gateway Enter the gateway IP address into the box if required gt Primary DNS Enter the DNS Server IP address into the box if required gt Secondary DNS If your ISP provides another DNS server enter it into this field 5 Click Next to continue the Wireless settings page will appear as shown in Figure 3 9 12 TL WR720N METERME oleh tele Quick Setup Wireless Wireless Radio Enable SSID TP LINK 072048 Region United States Channel Auto Ww Mode 11bgn mixed Channel Width Auto Wireless Security O Disable Security WPA PSKWPA2 PSK PSK Password 12562350 fou can enter ASC ll characters between 8 and 63 or Hexadecimal characters between 8 and 64 O No Change Figure 3 9 Quick Setup Wireless Wireless Radio Enable or disable the wireless radio by choosing from the drop down list SSID Enter a value of up to 32 characters The same name of SSID Service Set Identification must be assigned to all wireless devices in your network Considering your wireless network security the default SSID is set to be TP LINK_XXXXXX XXXXXX indicates the last unique six numbers of each Router s MAC address This value is case s
30. 4 6 2 Wireless Security Choose menu Wireless Wireless Security and then you can configure the security settings of your wireless network The router has a default wireless password which is the same as PIN code and you can check the PIN code on the label attached to the product There are five wireless security modes supported by the Router WEP Wired Equivalent Privacy WPA Wi Fi Protected Access WPA2 Wi Fi Protected Access 2 WPA2 PSK Pre Shared Key and WPA PSK Pre Shared Key 2 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Wireless Security Current SID Disable Security WEP Type WEP Key Format Key Selected Key 1 Key 2 Key 3 Key 4 O WPA WPA2 Version Encryption Radius Server IP Radius Port Radius password Group Key Update Period WPA PSK WPA2 PSK Version Encryption PSK Password Group Key Update Period TP LINK E3660 Automatic kd WEF Key Key Type iat Bia ies 9 O ETT Automatic Automatic 1812 1 65535 0 stands for default port 1812 fin second minimum is 30 0 means no update Automatic AES 1234557890 Mou can enter ASC ll characters between 6 and 63 or Hexadecimal characters between 8 and 64 ob400 fin second minimum is 30 0 means no update Figure 4 17 gt Disable Security If you do not want to use wireless security select this check box but it s strongly recommended to choose one of the f
31. Address into the MAC Address field The format of the MAC Address iS XX XX XX XX XX XX X is any hexadecimal digit For example 00 OE AE B0 00 0B 2 Type the description of the PC in the Description field Fox example John s PC 3 Select Enabled or Disabled for this entry on the Status pull down list 4 Click the Save button to save this entry To add additional entries repeat steps 1 4 To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 2 Modify the information 3 Click the Save button Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and click the Previous button to return to the previous page Fox example If you want to block the PC with MAC addresses 00 OA EB 00 07 BE and 00 OA EB 00 07 5F to access the Internet first enable the Firewall and MAC Address Filtering on the Firewall page then you should specify the Default MAC Address Filtering Rule Deny these PC s with effective rules to access the Internet on the Firewall page and the following MAC address filtering list on this page Jescription 00 04 EB 00 07 HE John s computer Enabled 00 04 EB6 00 07 5F Alice s computer Enabled 4 9 5 Local Management Choose menu Security Local Management
32. Cabling Type 100BASE TX UTP category 5 5e cable maximum 100m EIA TIA 568 1000 STP maximum 100m LEDs PWR SYS WLAN WAN LAN WPS FCC CE Safety amp Emissions 2 4 2 4835GHz 11n up to 150Mbps Automatic gt Radio Data Rate 11g 54 48 36 24 18 12 9 6M Automatic 11b 11 5 5 2 1M Automatic Frequency Expansion DSSS Direct Sequence Spread Spectrum Modulation DBPSK DQPSK CCK OFDM 16 QAM 64 QAM WEP WPA WPA2 WPA2 PSK WPA PSK 130M 68dBm 10 PER 108M 68dBm 10 PER 54M 68dBm 10 PER Frequency Band Sensitivity PER 11M 85dBm 8 amp PER 6M 88dBm 10 PER 1M 90dBm 8 PER Environmental and Physical Operating OC 40 C 327 104 Storage 40 C 70 C 40 F 158 F Temperature Ed Operating 10 90 RH Non condensing umidity Storage 5 95 RH Non condensing Only 2 412GHz 2 462GHZ is allowed to be used in USA which means only channel 1 11 is available for American users to choose 99 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Appendix D Glossary gt 802 11n 802 11n builds upon previous 802 11 standards by adding MIMO multiple input multiple output MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity perhaps through coding schemes like Alamouti coding The Enhanced Wireless Consortium EWC 3 was formed to help acc
33. DDNS follow these instructions 1 Type the User Name for your DDNS account 2 Type the Password for your DDNS account 3 Type the Domain Name you received from dynamic DNS service provider 4 Click the Login button to log in the DDNS service Connection Status The status of the DDNS service connection is displayed here Click Logout to log out the DDNS service 4 16 System Tools System Tools Diagnostic Firmware Upgrade Factory Defaults Backup 4 Restore Reboot Password System Log Statistics Figure 4 78 The System Tools menu Choose menu System Tools and you can see the submenus under the main menu Time Settings Diagnostic Firmware Upgrade Factory Defaults Backup 8 Restore Reboot Password System Log and Statistics Click any of them and you will be able to configure the corresponding function The detailed explanations for each submenu are provided below 4 16 1 Time Settings Choose menu System Tools Time Setting and then you can configure the time on the following screen 79 TL WR720N METER EEE oleh tele Time zone GmMT 08 00 Beijing Hong Kong Perth Singapore 4 Date MM DDIYY Time HH MMiSS Primary NTP Server joooo fo ptional secondary NTP Server A O ptional Enable Daylight Saving Mote Click the GET GMT to Update the time from the internet with the pre defined servers or entering the customized serverdP Address or Domain Name inthe above frames Fi
34. Fi protected Access WPA2 PSK WPA PSK as well as advanced Firewall protections the TL WR720N 150Mbps Wireless N Router provides complete data privacy Flexible Access Control 3 The TL WR720N 150Mbps Wireless N Router provides flexible access control so that parents or network administrators can establish restricted access policies for children or staff It also supports Virtual Server and DMZ host for Port Triggering and then the network administrators can manage and monitor the network in real time with the remote management function Simple Installation Since the Router is compatible with virtually all the major operating systems it is very easy to manage Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide Before installing the Router please look through this guide to know all the Router s functions 1 2 Conventions The Router or TL WR720N mentioned in this guide stands for TL WR720N 150Mbps Wireless N Router without any explanation 29 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 1 3 Main Features gt Make use of IEEE 802 11n wireless technology to provide a wireless data rate of up to 150Mbps gt One 10 100M Auto Negotiation RJ45 WAN port two 10 100M Auto Negotiation RJ45 LAN ports supporting Auto MDI MDIX gt Provides WPA WPA2 WPA PSK WPA2 PSK authentication TKIP AES encryption security gt Shares data and Internet access for
35. If the general firewall switch is off even if IP Address Filtering Domain Filtering and MAC Address Filtering are enabled their settings are ineffective Firewall C Enable Firewall tthe general firewall switch C Enable IP Address Filtering Default IP Address Filtering Rules O Allow the packets not specified by any filtering rules to pass through the device Deny the packets not specified by any filtering rules to pass through the device C Enable Domain Filtering C Enable MAC Address Filtering Default MAC Address Filtering Rules Allow these PCs with enabled rules to access the Internet Deny these PCs with enabled rules to access the Internet Figure 4 38 Firewall Settings gt Enable Firewall the general firewall switch is on or off gt Enable IP Address Filtering set IP Address Filtering is enabled or disabled There are two default filtering rules of IP Address Filtering either Allow or Deny passing through the router gt Enable Domain Filtering set Domain Filtering is enabled or disabled 49 TL WR720N METER EEE oTa gt Enable MAC Address Filtering set MAC Address Filtering is enabled or disabled You can select the default filtering rules of MAC Address Filtering either Allow or Deny accessing the router 4 9 2 IP Address Filtering The IP address Filtering feature allows you to control Internet Access by specific users on your LAN based on their IP addresses The IP address
36. Line A technology that allows data to be sent or received over existing traditional phone lines gt ISP Internet Service Provider A company that provides access to the Internet gt MTU Maximum Transmission Unit The size in bytes of the largest packet that can be transmitted gt NAT Network Address Translation NAT technology translates IP addresses of a local area network to a different IP address for the Internet gt PPPoE Point to Point Protocol over Ethernet PPPoE is a protocol for connecting remote hosts to the Internet over an always on connection by simulating a dial up connection gt SSID A Service Set Identification is a thirty two character maximum alphanumeric key 100 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router identifying a wireless local area network For the wireless devices in a network to communicate with each other all devices must be configured with the same SSID This is typically the configuration parameter for a wireless PC card lt corresponds to the ESSID in the wireless Access Point and to the wireless network name gt WEP Wired Equivalent Privacy A data privacy mechanism based on a 64 bit or 128 bit or 152 bit shared key algorithm as described in the IEEE 802 11 standard gt Wi Fi A trade name for the 802 11b wireless networking standard given by the Wireless Ethernet Compatibility Alliance WECA see http www wi fi net an industry sta
37. NG Roll ie lid 2 t2 SCONVEMUOMS sron aeiio a a ae eha GE EA S 2 1 3 MANS bes iD 3 A A A A eter alana 4 TAR Ne Eron Panels aca cia suntuea tints 4 t42 Ane Rear Panel ra iia 5 Chapter 2 Connecting the Router soroa aaa ds 6 Zed System Requirements ae 6 2 2 Installation Environment Requirements ococccccccccocnconcoccocncnnconooconononnoncnonnnanoncnonnnanennnos 6 2 9 COMMEGCUMG Me ROQUES A tds 6 Chapter 3 Quick Installation GUI eta os 8 3 1 TOPAPLOAIU AMM o dl dd eae ticks 8 32 Quick INStAllatlOn GUS sssrin id it id 9 Chapter 4 Configuring the Router cito ias eee 15 Aok o 9 reer nee me as ents a A Renee EY TE 15 Me Ze Se Sr hiss otc ectceat a tte erent 15 A OUK SEU acosa 16 O 16 do INSI Ai 19 L EAN eaa aa Sok tac cantante ce satteoheateb eect 19 AZ VAN indio 20 An MACS di bb dd ota 29 AOS ANTOGS Sto iio in icoon 29 AGA Wireless ocn ti dort eco 30 4 6 2 Wireless Securities dc 32 4 6 3 Wireless MAC Filtering cooococoncconccccnoconococononncconoconocncnnnnnonanonannnncnenanenoss 35 4104 Wireless AMAN Ci ici 38 4 6 5 Wireless StaliStiCs iii A ad 39 A IDEC A eee et eR ctr oer eden eee eee Pe ee oe eee 40 ate A tatoos Se anctaacdencueenen aan 40 AZ DACP Client ea 41 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router A To Address INGSCIVAUOM beienee 42 AO IRONIA id dins 43 4ST MS do anaes 43 48 2 Porn TNggeriNg cr da 45 A ne E OO O eee ee eee eee eee ee 47 TEA ORIRE
38. O Approximate round trip times in milli seconds Minimum Bms Maximum ms Average Pms C Documents and Settings tplink gt Figure 3 1 Success result of Ping command 8 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router gt If the result displayed is similar to the Figure 3 2 it means the connection between your PC and the Router failed ce C WINDOWS system3 7 cmd exe Microsoft Windows AF Yersion 5 1 2600 Co Copyright 1985 2661 Microsoft Corp GCirPocuments and Settings tplink gt ping 192 168 60 1 Pinging 192 168 0 1 with 32 bytes of data Destination host unreachable Destination host unreachable Destination host unreachable Destination host unreachable Ping statistics for 192 168 6 1 Packets Sent 4 Feceived A Lost 4 ciz loss C Documents and Settings tplink Figure 3 2 Failure result of Ping command Please check the connection following these steps 1 Is the connection between your PC and the Router correct Note The 1 2 LEDs of LAN ports which you link to on the Router and LEDs on your PC s adapter should be lit 2 Is the TCP IP configuration for your PC correct Note If the Router s IP address is 192 168 0 1 your PC s IP address must be within the range of 192 168 0 2 192 168 0 254 3 Try the IP address 192 168 1 1 E Note If the LAN IP of the modem connected with your router is 192 168 0 x the default LAN IP of the Rout
39. Port in the address field of the Web browser If the LAN IP of the modem connected with your router is 192 168 1 x the default LAN IP of the Router will automatically switch from 192 168 0 1 to 192 168 1 1 to avoid IP conflict in this case please try http 192 168 1 1 88 3 Log in to the Router click the Forwarding menu on the left of your browser and click the Virtual Servers submenu On the Virtual Servers page click Add New then on the Add or Modify a Virtual Server page enter 80 into the blank next to the Service Port and your IP address next to the IP Address assuming 192 168 0 169 for an example remember to Enable and Save Virtual Servers ID Service Port Internal Port IP Address Protocol Status Modify 1 80 80 192 168 0 169 ALL Enabled Modify Delete Add New Enable All Disable All Delete All Figure A 8 Virtual Servers 94 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Add or Modify a Virtual Server Entry Service Port DOCIOC OT XX internal Port XX Only valid for single Service Port or leave a blank IP Address 192 166 0 169 Protocol ALL we Status Enabled ha Common Service Port Select ne Figure A 9 Add or Modify a Virtual server Entry 5 The wireless stations cannot connect to the Router 1 Make sure the Wireless Router Radio is enabled 2 Make sure that the wireless stations SSID accord with the Router s SSID 3 Make
40. R720N 150Mbps Wireless N Router 50Mbps Wireless N Router ID MAC address Website Description Schedule Enable Modify 1 00 11 22 33 44 A4A Allow Google schedule_1 Edit Delete Add New Enable All Disable All Delete All Figure 4 51 Parental Control Settings 4 11 Access Control Access Control Host Target Schedule Figure 4 52 Access Control There are four submenus under the Access Control menu as shown in Figure 4 52 Rule Host Target and Schedule Click any of them and you will be able to configure the corresponding function 4 11 1 Rule Choose menu Access Control Rule and then you can view and set Access Control rules in the screen as shown in Figure 4 53 Access Control Rule Management C Enable Internet Access Control Default Filter Policy Allow the packets specified by any enabled access control policy to pass through the Router Deny the packets specified by any enabled access control policy to pass through the Router Save ID Rule Name Target Schedule Enable Setup Wizard Add New Current No Figure 4 53 Access Control Rule Management gt Enable Internet Access Control Select the check box to enable the Internet Access Control function so the Default Filter Policy can take effect gt Rule Name Here displays the name of the rule and this name is unique gt Host Here displays the host selected in the corresponding rule gt
41. TP LINK User Guide TL WR720N 150Mbps Wireless N Router A E 3 Rev 1 0 0 1910010617 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2012 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT HE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following m
42. Tre BUMOram HOPMaTUBHUX OOKYMeHTIB Ta BUMOlaM LO nepernbayehi 4NHHNMA 3AaKOHOAaBANMY AKTaAaMu YkpalHn TP LINK TP LINK TECHNOLOGIES CO LTD DECLARATION OF CONFORMITY For the following equipment Product Description 150Mbps Wireless N Router Model No TL WR720N Trademark TP LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives Directives 1999 5 EC Directives 2004 108 EC Directives 2006 95 EC Directives 1999 519 EC Directives 2011 65 EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1 7 1 2006 ETSI EN 301 489 1 V1 8 1 2008 amp ETSI EN 301 489 17 V2 1 1 2009 EN 55022 2010 EN 55024 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN60950 1 2006 A11 2009 A1 2010 EN62311 2008 The product carries the CE Mark C 1588 Person is responsible for marking this declaration Yang Hongliang Product Manager of International Business Date of issue 2012 TP LINK TECHNOLOGIES CO LTD Building 24 floors 1 3 4 5 and 28 floors 1 4 Central Science and Technology Park Shennan Rd Nanshan Shenzhen China TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router CONTENTS Package COntents perenne as ie ee E E ti 1 Chapter 1 TEER OCC UIC ii a a eer a 2 Tel ONGIVIGW OT I
43. WAN and then you can configure the IP parameters of the WAN on the screen below 1 If your ISP provides the DHCP service please choose Dynamic IP type and the Router will automatically get IP parameters from your ISP You can see the page as follows Figure 4 7 WAN Connection Type Dynamic IP we IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 MTU Size in bytes 1500 The defaultis 1500 do not change unless necessary C Use These DNS servers Secondary DNS ooon Optional Host Name WERF20N C Get IP with Unicast DHCP tis usually not required Dave Figure 4 7 WAN Dynamic IP This page displays the WAN IP parameters assigned dynamically by your ISP including IP address Subnet Mask Default Gateway etc Click the Renew button to renew the IP parameters from your ISP Click the Release button to release the IP parameters gt MTU Size The normal MTU Maximum Transmission Unit value for most Ethernet networks is 1500 Bytes It is not recommended that you change the default MTU Size unless required by your ISP gt Use These DNS Servers If your ISP gives you one or two DNS addresses select Use These DNS Servers and enter the primary and secondary addresses into the correct fields Otherwise the DNS servers will be assigned dynamically from your ISP Note If you find error when you go to a Web site after entering the DNS addresses it is likely that your
44. Wireless N Router is http tplinklogin net the default IP address is 192 168 0 1 and the default Subnet Mask is 255 255 255 0 These values can be changed as you desire In this guide we all use the default values for description Connect the local PC to the LAN ports of the Router and then you can configure the IP address for your PC by following the steps below 1 Setup the TCP IP Protocol in Obtain an IP address automatically mode on your PC If you need instructions as to how to do this please refer to Appendix B Configuring the PC 2 Then the built in DHCP server will assign IP address for the PC Now you can run the Ping command in the command prompt to verify the network connection between your PC and the Router The following example is in Windows XP OS Open a command prompt and type ping 192 168 0 1 and then press Enter gt Ifthe result displayed is similar to the Figure 3 1 it means the connection between your PC and the Router has been established well er C WINDOWS system3 cmd exe Microsoft Windows AF Version 5 1 2600 LG Copyright 1985 2001 Microsoft Corp C gt Documents and Settings tplink gt ping 192 168 60 1 Pinging 192 168 0 1 with 32 bytes of data 192 168 68 1 bytes 32 time lt ims 192 168 868 141 hytes 32 time lt ims 192 168 8 1 hytes 32 time lt ims Reply from 192 168 0 1 bytes 32 time lt imse Ping statistics for 192 168 M 1 Packets Sent 4 Received 4 Lost A Az E
45. a roma ee een eee 47 ARTE E 210 8 i A y ee ee ee ee eee eee 49 AOT do 49 4 9 2 IPAddress A A 50 42929 D mam FONO t AA 51 AOA MAC Address Hllterin dia as a a 53 4 9 5 Local Manage MEN divas A o 54 4 90 Remote Manadementasin int nal aaa 99 49 7 Advanced SOCUMNY ia it 56 4 10 Parental Control sica 58 AA ACCESS OO A A ee 61 Si A 0 E E OOPS O E A Seer are ee ee re eee eee 61 EZ dios 67 4 Y A Pere EE eee eT Re Peo ee ee ae 68 1 ns a ys ahd ian deabinal a E E eat by 70 4 12 Statie ROUINO eiiean ya E 72 A o ee ee eee ee 73 AVA IP SMAC BINAN G ter ese iee seed cones onda irate ae cule E 74 414 1 BANGING gt CUNO Spiess tenet Ae ion chennai atta la that Sec dat Suh wi ducehd kneels 74 AAA ARS E E Ee a Pee are RS 76 A To Dynami DN Saten E eaasstecadel 76 Ai b COmexeicn DDNS cann laa 77 4 15 2 Dynans org DDNS vos id 77 4 19 0 NOID Cont DON Smart a 78 A16 OVS tom a Saar hued os bah ands disease 79 AT MAME SUN Si a a OE 79 AO Z gt DANOS A Es 81 40 3 FNMWare Upgrade ii ao Dni e ano delo Es 83 A TOF Factory Detaulls oi tt dl 84 416 9 BackUPS RESIO ruan A N AN 84 AO O RODOO boria E a A eee ee eee 85 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router AMO PASS WO bold 86 ATG ON SIC INWOOD s25 6st ede tasact A E 86 AO SIAUSUCS xt cies tose ds 88 Append A FAQ aia 91 Appendix B Configuring the PCS ii tia 96 Appendix C Specification Sica ao an 99 Append D GIOSS Masias 100 TL WR720N 150Mbps Wireless N Rout
46. age 2 In Schedule Description field create a unique description for the schedule e g Schedule_1 3 In Day field check the Select Days radio button and then select Sat and Sun 4 In Time field enter 1800 in Start Time field and 2000 in Stop Time field 5 Click Save to complete the settings f TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Then you will go back to the Schedule Settings page and see the following list D Schedule Description Day Time Modify Schedule 1 Sat Sun 18 00 20 00 Edit Delete 4 12 Static Routing A static route is a pre determined path that network information must travel to reach a specific host or network To add or delete a route work in the area under the Static Routing page Static Routing List Destination IP Address Subnet Mask Default Gateway Status Modify Add Mew Figure 4 67 Static Routing List To add static routing entries 1 Click the Add New button 2 Enter the following data gt Destination IP Address The Destination IP Address is the address of the network or host that you want to assign to a static route gt Subnet Mask The Subnet Mask determines which portion of an IP Address is the network portion and which portion is the host portion gt Gateway This is the IP Address of the gateway device that allows for contact between the router and the network or host 3 Select Enabled or Disabled for this entry on the Status
47. an view and set a Host list in the screen as shown in Figure 4 59 The host list is necessary for the Access Control Rule Host Settings ID Host Description Information Modify 1 Host_1 IP 192 168 0 1 192 168 0 23 Edit Delete Add New Delete All Current No 1 w Page Figure 4 59 Host Settings gt Host Description Here displays the description of the host and this description is unique gt Information Here displays the information about the host It can be IP or MAC gt Modify To modify or delete an existing entry To add a new entry please follow the steps below 1 Click the Add New button 2 Inthe Mode field select IP Address or MAC Address e f you select IP Address the screen shown is Figure 4 60 1 In Host Description field create a unique description for the host e g Host_1 2 In LAN IP Address field enter the IP address e If you select MAC Address the screen shown is Figure 4 61 1 In Host Description field create a unique description for the host e g Host_1 2 In MAC Address field enter the MAC address 3 Click the Save button to complete the settings Click the Delete All button to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page Add or Modify a Host Entry Mode IP Address e Host Description Host 1 LAN IP Address 192 168 0 1 1192 168 0 23 Figure 4 60 Add or Modify a H
48. atic IP You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP gt Connect on Demand In this mode the Internet connection can be terminated automatically after a specified inactivity period Max Idle Time and be re established when you attempt to access the Internet again If you want your Internet connection keeps active all the time please enter O in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet access disconnects gt Connect Automatically The connection can be re established automatically when it was down gt Time based Connecting The connection will only be established in the period from the 22 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router start time to the end time both are in HH MM format E Note Only when you have configured the system time on System Tools gt Time Settings page will the Time based Connecting function can take effect gt Connect Manually You can click the Connect Disconnect button to connect disconnect immediately This mode also supports the Max Idle Time function as Connect on Demand mode The Internet connection can be disconnected automatically after a specified inactivity period and re established when you attempt to access the Internet again Caution Sometimes the connection cannot be terminated although yo
49. ay Choose Select Days and select the certain day days or choose Everyday gt Time Select 24 hours or specify the Start Time and Stop Time yourself gt Start Time Enter the start time in HAMM format HHMM are 4 numbers For example 0800 is 8 00 gt Stop Time Enter the stop time in HHMM format HHMM are 4 numbers For example 2000 is 20 00 4 Click Next when finishing creating the advanced schedule entry and the next screen will appear as shown in Figure 4 57 64 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Quick Setup Create an Internet Access Control Entry Rule Name Host Ha st 1 dl Target Target 1 Schedule Schedule 1 Status Enabled Back Finish Figure 4 57 Quick Setup Create an Internet Access Control Entry gt Rule In this field create a name for the rule Note that this name should be unique e g Rule_1 gt Host In this field select a host from the drop down list for the rule The default value is the Host Description you set just now gt Target In this filed select a target from the drop down list for the rule The default value is the Target Description you set just now gt Schedule In this field select a schedule from the drop down list for the rule The default value is the Schedule Description you set just now gt Status In this field there are two options Enable or Disable Select Enable so that the rule
50. ays the day s in a week Time Here displays the time period in a day Modify Here you can edit or delete an existing schedule 70 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router To add a new schedule follow the steps below 1 Click Add New button shown in Figure 4 65 and the next screen will pop up as shown in Figure 4 66 2 In Schedule Description field create a unique description for the schedule e g Schedule 1 3 In Day field select the day or days you need 4 In Time field you can select all day 24 hours or you may enter the Start Time and Stop Time in the corresponding field 5 Click Save to complete the settings Click the Delete All button to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page Advance Schedule settings Mote The Schedule is based on the time ofthe Router Schedule Description Po Day Everyday Select Days hor THE Wed Thu Fri Sat sun Time all day 24 hours Start Time HHMM stop Time A HHMI Figure 4 66 Advanced Schedule Settings For example If you desire to restrict the internet activities of host with MAC address 00 11 22 33 44 AA to access www google com only from 18 00 to 20 00 on Saturday and Sunday you should first follow the settings below 1 Click Add New button shown in Figure 4 65 to enter the Advanced Schedule Settings p
51. bps Wireless N Router gt MTU Size The normal MTU Maximum Transmission Unit value for most Ethernet networks is 1500 Bytes It is not recommended that you change the default MTU Size unless required by your ISP gt Connect on Demand In this mode the Internet connection can be terminated automatically after a specified inactivity period Max Idle Time and be re established when you attempt to access the Internet again If you want your Internet connection keeps active all the time please enter 0 in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet access disconnects gt Connect Automatically The connection can be re established automatically when it was down gt Connect Manually You can click the Connect Disconnect button to connect disconnect immediately This mode also supports the Max Idle Time function as Connect on Demand mode The Internet connection can be disconnected automatically after a specified inactivity period and re established when you attempt to access the Internet again Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately Caution Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background Click the Save button to save your settings 5 If your ISP provides L2TP c
52. by any enabled access control policy to pass through the Router 2 Werecommend that you click Setup Wizard button to finish all the following settings 3 Click the submenu Host of Access Control in the left to enter the Host List page Add a new entry with the Host Description is Host_1 and MAC Address is 00 11 22 33 44 AA 4 Click the submenu Target of Access Control in the left to enter the Target List page Add a new entry with the Target Description is Target_1 and Domain Name is www google com 5 Click the submenu Schedule of Access Control in the left to enter the Schedule List page Add a new entry with the Schedule Description is Schedule_1 Day is Sat and Sun Start Time is 1800 and Stop Time is 2000 6 Click the submenu Rule of Access Control in the left Click Add New button to add a new rule as follows e In Rule Name field create a name for the rule Note that this name should be unique for example Rule_1 e In Host field select Host_1 e In Target field select Target_1 e In Schedule field select Schedule 1 e In Status field select Enable e Click Save to complete the settings Then you will go back to the Access Control Rule Management page and see the following list ID Rule Name Target Schedule Enable Modify 1 Rule_1 Target 1 schedule 1 Edit Delete 66 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 11 2 Host Choose menu Access Control Host and then you c
53. ce such as Internet gaming or videoconferencing The Router forwards packets of all services to the DMZ host Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function Current DMZ Status Enable Disable DMZ Host IP Address 192 168 0 100 Figure 4 35 DMZ To assign a computer or server to be a DMZ server 1 Click the Enable button 2 Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field 3 Click the Save button 4 8 4 UPnP Choose menu Forwarding UPnP and then you can view the information about UPnP in the screen shown in Figure 4 36 The Universal Plug and Play UPnP feature allows the devices such as Internet computers to access the local host resources or devices as needed UPnP devices can be automatically discovered by the UPnP service application on the LAN 47 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Current UPnP Status Enabled Current UPnP Settings List ID App Description External Port Protocol Internal Port IP Address Status BitComet i92 166 0 100 25959 25959 TER 273959 192 166 0 100 Enabled 2 BitComet 192 166 0 100 25959 23959 UDOP 73959 192 166 0 100 Enabled Figure 4 36 UPnP Setting gt Current UPnP Status UPnP can be enabled or disabled by clicking the Enable
54. cimal notation provided by your ISP 3 If your ISP provides a PPPoE connection select PPPoE Russia PPPoE option And you should enter the following parameters Figure 4 9 21 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router WAN Connection Type PPPOE Russia PPPoE PPPoE Connection User Name username Secondary Connection Disabled Dynamic StaticiP For Dual Access Russia PPPoE Wan Connection Mode Connect on Demand hax Idle Time minutes 0 means remaining active all the time O Connect Automatically O Time based Connecting Period ofTime from o o HH MM to 23 so HH Mit Connect Manually hax Idle Time 15 minutes 0 means remaining active all the time WAN port is unplugged Figure 4 9 WAN PPPoE gt User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive gt Secondary Connection It s available only for PPPoE Connection If your ISP provides an extra Connection type such as Dynamic Static IP to connect to a local area network then you can check the radio button of Dynamic Static IP to activate this secondary connection e Disabled The Secondary Connection is disabled by default so there is PPPoE connection only This is recommended e Dynamic IP You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP e St
55. configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 4 85 84 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Backup Restore Backup Figure 4 85 Backup amp Restore Configuration gt Click the Backup button to save all configuration settings as a backup file in your local computer gt To upgrade the Router s configuration follow these instructions e Click the Browse button to find the configuration file which you want to restore e Click the Restore button to update the configuration with the file whose path is the one you have input or selected in the blank Note The current configuration will be covered with the uploading configuration file Wrong process will lead the device unmanaged The restoring process lasts for 20 seconds and the Router will restart automatically then Keep the power of the Router on during the process in case of any damage 4 16 6 Reboot Choose menu System Tools Reboot and then you can click the Reboot button to reboot the Router via the next screen Click this button to rebootthe device Figure 4 86 Reboot the Router Some settings of the Router will take effect only after rebooting which include e Change the LAN IP Address system will reboot automatically e Change the DHCP Settings e Change the Wireless configurations e Change the Web Management Port e Upgrade the firmware
56. dding Ping Packet to access the router from the LAN port The default value is disabled If enabled the ping packet from the LAN port cannot access the router Defends against some viruses Click the Save button to save the settings Click the Blocked DoS Host Table button to display the DoS host table by blocking The page will appear Blocked Dos Host List ID Host IP Address Host MAC Address Modify 1 192 1608 1 103 00 13 44 B0 77 Delete Figure 4 48 Thwarted DoS Host Table This page shows Host IP Address and Host MAC Address for each host blocked by the router gt Host IP Address The IP address that blocked by DoS are displayed here gt Host MAC Address The MAC address that blocked by DoS are displayed here To update this page and to show the current blocked host click on the Refresh button Click the Clear All button to clear all displayed entries After the table is empty the blocked host will regain the capability to access Internet Click the Return button to return to the Advanced Security page 4 10 Parental Control Choose menu Parental Control and then you can configure the parental control in the screen as shown in Figure 4 49 The Parental Control function can be used to control the internet activities of the child limit the child to access certain websites and restrict the time of surfing Parental Control Settings Mon Parental PCs not listed will not be able to access the Internet Parenta
57. dify To modify or delete an existing entry To add a new entry please follow the steps below 1 Click the Add New button 2 In Mode field select IP Address or Domain Name 68 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 3 If you select IP Address the screen shown is Figure 4 63 Add or Modify an Access Target Entry Mode IP Address se Protocol Common Service Port please select Y Figure 4 63 Add or Modify an Access Target Entry 1 In Target Description field create a unique description for the target e g Target 1 2 In IP Address field enter the IP address of the target 3 Select a common service from Common Service Port drop down list so that the Target Port will be automatically filled If the Common Service Port drop down list doesn t have the service you want specify the Target Port manually 4 In Protocol field select TCP UDP ICMP or ALL from the drop down list 4 Ifyou select Domain Name the screen shown is Figure 4 64 Add or Modify an Access Target Entry Figure 4 64 Add or Modify an Access Target Entry 1 In Target Description field create a unique description for the target e g Target 1 2 In Domain Name field enter the domain name either the full name or the keywords for example google in the blank Any domain name with keywords in it 69 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router www google com www googl
58. e cn will be blocked or allowed You can enter 4 domain names 5 Click the Save button Click the Delete All button to delete all the entries in the table Click the Next button to go to the next page or click the Previous button to return to the previous page For example If you desire to restrict the internet activities of host with MAC address 00 11 22 33 44 AA in the LAN to access www google com only you should first follow the settings below 1 Click Add New button in Figure 4 62 to enter the Add or Modify an Access Target Entry page In Mode field select Domain Name from the drop down list In Target Description field create a unique description for the target e g Target_1 In Domain Name field enter www google com 1 A AS Click Save to complete the settings Then you will go back to the Target Settings page and see the following list D Target Description information Modify Target_1 Wii google com Edit Delete 4 11 4 Schedule Choose menu Access Control Schedule and then you can view and set a Schedule list in the next screen as shown in Figure 4 65 The Schedule list is necessary for the Access Control Rule schedule Settings D schedule Description Time Modify 1 schedule_1 00 00 24 00 Edit Delete Add Mew Delete All Figure 4 65 Schedule Settings gt Schedule Description Here displays the description of the schedule and this description is unique Day Here displ
59. easures gt Reorient or relocate the receiving antenna gt Increase the separation between the equipment and receiver gt Connect the equipment into an outlet on a circuit different from that to which the receiver is connected gt Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter To comply with FCC RF exposure compliance requirements this grant is applicable to only Mobile Configurations The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co l
60. ecurity by generating a new PIN gt Add device You can add a new device to the existing network manually by clicking this button b To add a new device If the wireless adapter supports Wi Fi Protected Setup WPS you can establish a wireless connection between wireless adapter and Router using either Push Button Configuration PBC method or PIN method cf Note To build a successful connection by WPS you should also do the corresponding configuration of the new device for WPS function meanwhile I Use the Wi Fi Protected Setup Button Use this method if your client device has a Wi Fi Protected Setup button Step 1 Press the WPS button on the back panel of the Router You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4 2 then Choose Press the button of the new device in two minutes and click Connect Shown in the following figure 17 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Add A New Device Enter the new device s PIM Press the button of the new device in two minutes Figure 4 3 Add A New Device Step 2 Press and hold the WPS button of the client device directly Step 3 The Wi Fi Protected Setup LED flashes for two minutes during the Wi Fi Protected Setup process Step 4 When the WPS LED is on the client device has successfully connected to the Router Step 5 Refer back to your client device or its documentation for further
61. ed Rules Choose how the displayed statistics are sorted Select the Auto refresh checkbox to refresh automatically Click the Refresh button to refresh immediately Click Reset All to reset the values of all the entries to zero Click Delete All to delete all entries in the table 89 TL WR720N MEME EEE oleh tele Statistics Table IPIMAG Address IPIMAG Address The IP and MAC address are displayed with related statistics Packets The total number of packets received and transmitted by the Router Total The total number of bytes received and transmitted by the Router The total number of packets received and transmitted in the last Packets Statistic interval seconds The total number of bytes received and transmitted in the last Packets Statistic interval seconds The number of the ICMP packets transmitted to WAN per second at the ICMP Tx specified Packets Statistics interval It is shown like current transmitting rate Current Max transmitting rate The number of UDP packets transmitted to the WAN per second at the UDP Tx specified Packets Statistics interval It is shown like current transmitting rate Max transmitting rate The number of TCP SYN packets transmitted to the WAN per second at the TCP specified Packets Statistics interval It is shown like current transmitting rate SYN Tx Max transmitting rate Reset Reset the value of he entry to zero Modify Delete the existing entry in
62. efault setting is 11bgn mixed 11b only Select if all of your wireless clients are 802 11b 11g only Select if all of your wireless clients are 802 110 11n only Select only if all of your wireless clients are 802 11n 11bg mixed Select if you are using both 802 11b and 802 11g wireless clients 11bgn mixed Select if you are using a mix of 802 11b 11g and 11n wireless clients Select the desired wireless mode When 802 11g mode is selected only 802 11g wireless stations can connect to the Router When 802 11n mode is selected only 802 11n wireless stations can connect to the AP It is strongly recommended that you set the Mode to 802 11b amp g amp n and all of 802 11b 802 11g and 802 11n wireless stations can connect to the Router gt Channel width Select any channel width from the drop down list The default setting is Auto which can automatically adjust the channel width for your clients E Note If 11b only 11g only or 11bg mixed is selected in the Mode field the Channel Width selecting field will turn grey and the value will become 20M which is unable to be changed gt Enable Wireless Router Radio The wireless radio of this Router can be enabled or disabled to allow wireless stations access gt Enable SSID Broadcast When wireless clients survey the local area for wireless networks to associate with they will detect the SSID broadcast by the Router If you select the Enable SSID Broadcast checkbox t
63. elerate the IEEE 802 11n development process and promote a technology specification for interoperability of next generation wireless local area networking WLAN products gt 802 11b The 802 11b standard specifies a wireless networking at 11 Mbps using direct sequence spread spectrum DSSS technology and operating in the unlicensed radio spectrum at 2 4GHz and WEP encryption for security 802 11b networks are also referred to as Wi Fi networks gt 802 11g specification for wireless networking at 54 Mbps using direct sequence spread spectrum DSSS technology using OFDM modulation and operating in the unlicensed radio spectrum at 2 4GHz and backward compatibility with IEEE 802 11b devices and WEP encryption for security gt DDNS Dynamic Domain Name System The capability of assigning a fixed host and domain name to a dynamic Internet IP Address gt DHCP Dynamic Host Configuration Protocol A protocol that automatically configure the TCP IP parameters for the all the PC s that are connected to a DHCP server gt DMZ Demilitarized Zone A Demilitarized Zone allows one local host to be exposed to the Internet for a special purpose service such as Internet gaming or videoconferencing gt DNS Domain Name System An Internet Service that translates the names of websites into IP addresses gt Domain Name A descriptive name for an address or group of addresses on the Internet gt DSL Digital Subscriber
64. ensitive For example TEST is NOT the same as fest Region Select your region from the drop down list This field specifies the region where the wireless function of the Router can be used It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field If your country or region is not listed please contact your local government agency for assistance gt Channel This field determines which operating frequency will be used The default channel is set to Auto so the AP will choose the best channel automatically It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point gt Mode This field determines the wireless mode which the Router works on gt Channel Width Select any channel width from the drop down list The default setting is automatic which can automatically adjust the channel width for your clients gt Disable Security The wireless security function can be enabled or disabled If disabled the wireless stations will be able to connect the Router without encryption It is strongly recommended that you choose one of following options to enable security gt WPA PSK WPA2 PSK Select WPA based on pre shared passphrase 42 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router e PSK Password You can enter ASCII or Hexadecimal characters For ASCII the key can be made
65. eply from 202 108 225 byres b64 time 1 TTL 127 seq 3 Reply from 202 108 225 bytes 64 time 1 TTL 127 seq 4 Figure 4 82 Diagnostic Results E Note 1 Only one user can use the diagnostic tools at one time 2 Ping Count Ping Packet Size and Ping Timeout are Ping Parameters and Traceroute Max TTL is Traceroute Parameter 4 16 3 Firmware Upgrade Choose menu System Tools Firmware Upgrade and then you can update the latest version of firmware for the Router on the following screen Firmware Upgrade Firmware Version 419 44 Build 120331 Rel 5707 7n Hardware Version WR720N 1 0 00000000 Figure 4 83 Firmware Upgrade gt Firmware Version Displays the current firmware version gt Hardware Version Displays the current hardware version The hardware version of the upgrade file must accord with the Router s current hardware version To upgrade the Router s firmware follow these instructions below 1 Download a most recent firmware upgrade file from our website www tp link com 2 Enter or select the path name where you save the downloaded file on the computer into the File Name blank Click the Upgrade button The Router will reboot while the upgrading has been finished 83 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router E Note 1 New firmware versions are posted at http www tp link com and can be downloaded for free There is no need to upgrade the firmware
66. er 50Mbps Wireless N Router Package Contents The following items should be found in your package gt TL WR720N 150Mbps Wireless N Router gt Power Adapter for TL WR720N 150Mbps Wireless N Router gt Quick Installation Guide gt Resource CD for TL WR720N 150Mbps Wireless N Router including e This Guide e Other Helpful Information E Note Make sure that the package contains the above items lf any of the listed items is damaged or missing please contact with your distributor TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Chapter 1 Introduction 1 1 Overview of the Router The 150Mbps Wireless N Router delivers exceptional range and speed which can fully meet the need of Small Office Home Office SOHO networks and the users demanding higher networking performance Incredible Speed gt The TL WR720N 150Mbps Wireless N Router provides up to 150Mbps wireless connection with other 802 11n wireless clients The incredible speed makes it ideal for handling multiple data streams at the same time which ensures your network stable and smooth The performance of this 802 11n wireless Router will give you the unexpected networking experience at speed 650 faster than 802 11g It is also compatible with all IEEE 802 11g and IEEE 802 11b products Multiple Security Protections With multiple protection measures including SSID broadcast control and wireless LAN 64 128 152 bit WEP encryption Wi
67. er will automatically switch from 192 168 0 1 to 192 168 1 1 to avoid IP conflict Therefore in order to verify the network connection between your PC and the Router you can open a command prompt and type ping 192 168 1 1 and then press Enter 3 2 Quick Installation Guide With a Web based Internet Explorer or Netscape Navigator utility it is easy to configure and manage the 150Mbps Wireless N Router The Web based utility can be used on any Windows Macintosh or UNIX OS with a Web browser 9 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 1 To access the configuration utility open a web browser and type the default address http tplinklogin net in the address field of the browser Address http tplinklagin net Figure 3 3 Login the Router After a moment a login window will appear similar to the Figure 3 4 Enter admin for the User Name and Password both in lower case letters Then click the OK button or press the Enter key Connect to tplinklogin net 15OMbps Wireless H Router TL WRTZOH User name admin e Password Figure 3 4 Login Windows Note If the above screen does not pop up it means that your Web browser has been set to a proxy Go to Tools menu gt Internet Options gt Connections gt LAN Settings in the screen that appears cancel the Using Proxy checkbox and click OK to finish it 2 After successfully log in you can click the Quick Setup to quickly configure
68. ere you can specify the transmit power of Router You can select High Middle or Low which you would like High is the default setting and is recommended gt Beacon Interval Enter a value between 40 1000 milliseconds for Beacon Interval here The beacons are the packets sent by the router to synchronize a wireless network Beacon Interval value determines the time interval of the beacons The default value is 100 gt RTS Threshold Here you can specify the RTS Request to Send Threshold If the packet is larger than the specified RTS Threshold size the router will send RTS frames to a particular receiving station and negotiate the sending of a data frame The default value is 2346 gt Fragmentation Threshold This value is the maximum size determining whether packets will be fragmented Setting the Fragmentation Threshold too low may result in poor network performance since excessive packets 2345 is the default setting and is recommended gt DTIM Interval This value determines the interval of the Delivery Traffic Indication Message DTIM A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages When the Router has buffered broadcast or multicast messages for associated clients it sends the next DTIM with a 38 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router DTIM Interval value You can specify the value between 1 255 Beacon Intervals
69. ernet again If you wish to activate Connect on Demand click the radio button If you want your Internet connection to remain active at all times enter O in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet connection terminates Connect Automatically Connect automatically after the Router is disconnected To use this option click the radio button Connect Manually You can configure the Router to make it connect or disconnect manually 26 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router After a specified period of inactivity Max Idle Time the Router will disconnect from your Internet connection and you will not be able to re establish your connection automatically as soon as you attempt to access the Internet again To use this option click the radio button If you want your Internet connection to remain active at all times enter 0 in the Max Idle Time field Otherwise enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested Caution Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time since some applications is visiting the Internet continually in the background 6 If your ISP provides PPTP connection please select PPTP Russia PPTP option And you should enter the following parameters Figure 4 13 WAN Connection Type PPTP Russia PPTP yl
70. ettings ARP Binding Disable Enable MAC Address IP Address Bind Modify 1 40 61 86 C4 98 43 192 168 0 100 Modify Delete Add New Enable All Disable All Delete Al Current Ho Page Figure 4 71 Binding Setting gt MAC Address The MAC address of the controlled computer in the LAN gt IP Address The assigned IP address of the controlled computer in the LAN 74 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router gt Bind Check this option to enable ARP binding for a specific device gt Modify To modify or delete an existing entry When you want to add or modify an IP amp MAC Binding entry you can click the Add New button or Modify button and then you will go to the next page This page is used for adding or modifying an IP amp MAC Binding entry shown in Figure 4 72 IP amp MAC Binding Settings MAC Address IP Address Figure 4 72 IP amp MAC Binding Setting Add amp Modify To add IP amp MAC Binding entries follow the steps below 1 Click the Add New button as shown in Figure 4 71 2 Enter the MAC Address and IP Address 3 Select the Bind checkbox 4 Click the Save button to save it To modify or delete an existing entry follow the steps below 1 Find the desired entry in the table 2 Click Modify or Delete as desired on the Modify column To find an existing entry follow the steps below 1 Click the Find button as shown in Figure 4 71 2 En
71. example if you want to block the PC s on your LAN to access websites www xxyy com cn www aabbcc com and websites with net in the end on the Internet while no limit for other websites you should specify the following Domain filtering list 0000 2400 Enabled 0800 2000 ww aabbec com Enabled O000 2400 net Enabled 4 9 4 MAC Address Filtering Like the IP Address Filtering page the MAC Address Filtering page allows you to control access to the Internet by users on your local network based on their MAC Address MAC Address Filtering Firewall Settings You can change them on Firewall page Enable Firewall Disabled Enable MAC Address Filtering Disabled Default Filtering Rules Deny these PCs with the enabled rules to access the Internet MAC Address Description Status Modify Add Mew Figure 4 43 MAC address Filtering Before setting up MAC Filtering entries you must ensure that Enable Firewall and Enable MAC Filtering have been selected on the Firewall page To Add a MAC Address filtering entry clicking the Add New button The page Add or Modify a MAC Address Filtering entry will appear shown in Figure 4 44 Add or Modify a MAC Address Filtering Entry Status Enabled ka Figure 4 44 Add or Modify a MAC Address Filtering entry 53 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router To add or modify a MAC Address Filtering entry follow these instructions 1 Enter the appropriate MAC
72. filtering is set on this page IP Address Filtering Firewall Settings You can change them on Firewall page Enable Firewall Disabled Enable IP Address Filtering Disabled Default Filtering Rules Deny the packets not specified by any filtering rules to pass through the device ID Effective time LAN IP Address LAN Pot WAN IP Address WAN Port Protocol Action Status Modify Figure 4 39 IP address Filtering To disable the IP Address Filtering feature keep the default setting Disabled To set up an IP Address Filtering entry click Enable Firewall and Enable IP Address Filtering on the Firewall page and click the Add New button The page Add or Modify an IP Address Filtering entry will appear shown in Figure 4 40 Add or Modify an IP Address Filtering Entry Effective time LAN IP Address LAN Port VVAN IP Address WAN Port Protocol ALL Action Deny Status Enabled Figure 4 40 Add or Modify an IP Address Filtering Entry To create or modify an IP Address Filtering entry please follow these instructions 1 Effective Time Enter a range of time in HHMM format which point to the range time for the entry to take effect For example 0803 1705 the entry will take effect from 08 03 to 17 05 2 LAN IP Address Enter a LAN IP Address or a range of LAN IP addresses in the field in dotted decimal notation format
73. for analysis by SYN Flood UDP Flood and ICMP Flood gt DoS Protection Enable or Disable the DoS protection function Only when it is enabled will the flood filters be effective gt Enable ICMP FLOOD Attack Filtering Enable or Disable the ICMP FLOOD Attack Filtering gt ICMP FLOOD Packets threshold 5 3600 The default value is 50 Enter a value between 5 3600 packets When the current ICMP FLOOD Packets numbers is beyond the set value the router will start up the blocking function immediately Enable UDP FLOOD Filtering Enable or Disable the UDP FLOOD Filtering UDP FLOOD Packets threshold 5 3600 The default value is 50 Enter a value between 5 3600 packets When the current UPD FLOOD Packets numbers is beyond the set value the router will start up the blocking function immediately gt Enable TCP SYN FLOOD Attack Filtering Enable or Disable the TCP SYN FLOOD Attack Filtering gt TCP SYN FLOOD Packets threshold 5 3600 The default value is 50 Enter a value between 5 3600 packets When the current TCP SYN FLOOD Packets numbers is beyond the set value the router will start up the blocking function immediately gt Ignore Ping Packet from WAN Port Enable or Disable ignore ping packet from WAN port The default is disabled If enabled the ping packet from the Internet cannot access the router 57 TL WR720N METER EEE oleh rele gt Forbid Ping Packet from LAN Port Enable or Disable forbi
74. g 1 Check the box to enable Daylight Saving 2 Select the start time from the drop down lists in the Start field 3 Select the end time from the drop down lists in the End field 4 Click the Save button to save the settings Enable Daylight Saving Figure 4 80 Time settings Note 1 This setting will be used for some time based functions such as firewall You must specify your time zone once you login to the router successfully otherwise these functions will not take effect The time will be lost if the router is turned off The Router will automatically obtain GMT from the Internet if it is configured accordingly The Daylight Saving will take effect one minute after the configurations are completed 4 16 2 Diagnostic Choose menu System Tools Diagnostic and then you can transact Ping or Traceroute function to check connectivity of your network in the following screen 81 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Vv Vv V WV Diagnostic Tools Diagnostic Parameters Diagnostic Tool Ping Traceroute IP Address Domain Name cece dl Ping Count a 1 50 Ping Packet Size 4 1472 Bytes Ping Timeout 100 2000 Millisecands Traceroute Max TTL Diagnostic Results The Router is ready Figure 4 81 Diagnostic Tools Diagnostic Tool Check the radio button to select one diagnostic too Ping This diagnostic tool troubleshoots connectivity reachab
75. get For some common service ports you can make use of the Common Service Port item below gt Protocol Here are four options All TCP UDP and ICMP Select one of them from the drop down list for the target gt Common Service Port Here lists some common service ports Select one from the drop down list and the corresponding port number will be filled in the Target Port field automatically For example if you select FTP 21 will be filled in the Target Port automatically If the Domain Name is selected you will see the following items 63 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router gt Domain Name Here you can enter 4 domain names either the full name or the keywords for example google Any domain name with keywords in it www google com www google cn will be blocked or allowed 3 Click Next when finishing creating the access target entry and the next screen will appear as shown in Figure 4 56 Quick Setup Create an Advanced Schedule Entry Note The Schedule is based on the time of the Router Schedule Description Day Everyday Select Days Mon Tue Wed Thu Fri Sat Sun Time all day 24 hours Start Time AA HHMM Stop Time e HHMM Figure 4 56 Quick Setup Create an Advanced Schedule Entry gt Schedule Description In this field create a description for the schedule Note that this description should be unique e g Schedule_ 1 gt D
76. gure 4 79 Time settings Time Zone Select your local time zone from this pull down list Date Enter your local date in MM DD YY into the right blanks Time Enter your local time in HH MM SS into the right blanks Primary NTP Server Secondary NTP Server Enter the address or domain of the Primary NTP Server or Secondary NTP Server and then the Router will get the time from the NTP Server preferentially In addition the Router built in some common NTP Servers so it can get time automatically once it connects the Internet Enable Daylight Saving Check the box to enable the Daylight Saving function Start The time to start the Daylight Saving Select the month in the first field the week in the second field the day in the third field and the time in the last field End The time to end the Daylight Saving Select the month in the first field the week in the second field the day in the third field and the time in the last field To set time manually 1 2 3 4 Select your local time zone Enter the Date in Month Day Year format Enter the Time in Hour Minute Second format Click Save To set time automatically 1 Z 3 Select your local time zone Enter the address or domain of the NTP Server I or NTP Server ll Click the Get GMT button to get system time from Internet if you have connected to the 80 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Internet To set Daylight Savin
77. he Wireless Router will broadcast its name SSID on the air gt Enable WDS Check this box to enable WDS With this function the Router can bridge two or more WLANs If this checkbox is selected you will have to set the following parameters as shown below Make sure the following settings are correct 31 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Enable WOS SSIDito be bridged Po BSSID to be bridged Example 00 1D 0F 11 22 33 Kev WEP Index Auth type e SSID to be bridged The SSID of the AP your Router is going to connect to as a client You can also use the search function to select the SSID to join e BSSID to be bridged The BSSID of the AP your Router is going to connect to as a client You can also use the search function to select the BSSID to join e Survey Click this button you can search the AP which runs in the current channel e Key type This option should be chosen according to the AP s security configuration It is recommended that the security type is the same as your AP s security type WEP Index This option should be chosen if the key type is WEP ASCII or WEP HEX It indicates the index of the WEP key e Auth Type This option should be chosen if the key type is WEP ASCII or WEP HEX It indicates the authorization type of the Root AP e Password If the AP your Router is going to connect needs password you need to fill the password in this blank
78. he change of wireless config will nottake effect until the Router reboot Figure 3 11 Quick Setup Finish 14 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Chapter 4 Configuring the Router This chapter will show each Web page s key functions and the configuration way 4 1 Login After your successful login you will see the main menu on the left of the Web based utility On the right there are the corresponding explanations and instructions Basic Settings Quick Setup WPS Network Wireless Advanced Settings DHCP Forwarding Security Parental Control Access Control Static Routing IP QoS IP amp MAC Binding Dynamic DNS Maintenance System Tools The detailed explanations for each Web page s key function are listed below 4 2 Status The Status page provides the current status information about the Router All information is read only 15 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Status Firmware Version 4 19 43 Build 120409 Rel 73769n Hardware Version WR 720N 1 0 00000000 MAC Address 00 0 EB 07 20 48 IP Address 192 168 0 1 subnet Mask 255 255 255 0 Wireless Wireless Radio Enable Name SSID TP LINK_OF 2048 Channel Automatic Current channel E Mode 11ban mixed Channel Width Automatic MAC Address O0 04 E8 07 20 48 WDS Status Disable MAC Address 00 04 E6 07 20 40 IP Address 192 166 1 102 Dynamic IP Subnet Mask
79. ies You can change the entry s order as desired Fore entries are before hind entries Enter the ID number in the first box you want to move and another ID number in second box you want to move to and then click the Move button to change the entry s order Click the Next button to the next page and click the Previous button to return to the previous page For example If you desire to block E mail received and sent by the IP Address 192 168 0 7 on your local network and to make the PC with IP Address 192 168 0 8 unable to visit the website of IP Address 202 96 134 12 while other PC s have no limit you should specify the following IP address filtering list Effective time LAN IP Address LAN Port WAN IP Address WAN Port Protocol Action Status Modify 0000 2400 192 168 0 7 25 ALL Deny Enabled Modify Delete 0000 2400 192 168 0 7 110 ALL Deny Enabled Modify Delete 0000 2400 192 168 0 8 202 96 134 12 ALL Deny Enabled Modify Delete 4 9 3 Domain Filtering The Domain Filtering page allows you to control access to certain websites on the Internet by 51 TL WR720N METER EEE oTa specifying their domains or key words Domain Filtering Firewall Settings You can change them on Firewall page Enable Firewall Disabled Enable Domain Filtering Disabled ID Effective time Domain Name Status Figure 4 41 Domain Filtering Before adding a Domain Filtering entry you must ensure that Enable Firewall and
80. ility and name resolution to a given host or gateway Traceroute This diagnostic tool tests the performance of a connection Note You can use ping traceroute to test both numeric IP address or domain name If pinging tracerouting the IP address is successful but pinging tracerouting the domain name is not you might have a name resolution problem In this case ensure that the domain name you are specifying can be resolved by using Domain Name System DNS queries IP Address Domain Name Enter the IP Address or Domain Name of the PC whose connection you wish to diagnose Pings Count Specifies the number of Echo Request messages sent The default is 4 Ping Packet Size Specifies the number of data bytes to be sent The default is 64 Ping Timeout Time to wait for a response in milliseconds The default is 800 Traceroute Max TTL Set the maximum number of hops max TTL to be reached in the path to search for the target destination The default is 20 Click Start to check the connectivity of the Internet 82 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router The Diagnostic Results page displays the result of diagnosis If the result is similar to the following screen the connectivity of the Internet is fine Diagnostic Results Pinging 202 108 225 with 64 bytes of data Reply from 202 108 225 btes 64 ftime 1 TTL 127 sedq 1 Reply from 202 108 225 bytes 64 time 1 TIlL 127 seq 2 R
81. instructions ll Enter the client device s PIN on the Router Use this method if your client device has a Wi Fi Protected Setup PIN number Step 1 Keep the default WPS Status as Enabled and click the Add device button in Figure 4 2 then the following screen will appear Add A New Device Enter the new device s PIN Press the button of the new device in two minutes Figure 4 4 Add A New Device Step 2 Enter the PIN number from the client device in the field on the above WPS screen Then click Connect button Step 3 Connect successfully will appear on the screen of Figure 4 4 which means the client device has successfully connected to the Router lil Enter the Router s PIN on your client device Use this method if your client device asks for the Router s PIN number Step 1 On the client device enter the PIN number listed on the Router s Wi Fi Protected Setup screen It is also labeled on the bottom of the Router Step 2 The Wi Fi Protected Setup LED flashes for two minutes during the Wi Fi Protected Setup process Step 3 When the WPS LED is on the client device has successfully connected to the Router Step 4 Refer back to your client device or its documentation for further instructions 18 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router cs Note 1 The WPS LED on the Router will light green for five minutes if the device has been successfully added to the network
82. ireless N Router 50Mbps Wireless N Router gt Modify To modify or delete an existing entry To setup a virtual server entry 1 Click the Add New button pop up Figure 4 32 2 Select the service you want to use from the Common Service Port list If the Common Service Port menu does not list the service that you want to use enter the number of the service port or service port range in the Service Port field 3 Enter the IP address of the computer running the service application in the IP Address field 4 Select the protocol used for this application in the Protocol drop down list either TCP UDP or All 5 Select the Enabled option in the Status drop down list 6 Click the Save button Add or Modify a Virtual Server Entry Service Port ARA OF KO IP Address hgt Status Enabled w z wt Common Serice Port Select ne Figure 4 32 Add or Modify a Virtual Server Entry E Note It is possible that you have a computer or server that has more than one type of available service If so select another service and type the same IP address for that computer or server To modify or delete an existing entry 1 Find the desired entry in the table 2 Click Modify or Delete as desired on the Modify column Click the Enable Disable All button to make all entries enabled disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and click the Previous button t
83. is managing the Router If the MAC address is required you can click the Clone MAC Address button and this MAC address will fill in the WAN MAC Address field Click Restore Factory MAC to restore the MAC address of WAN port to the factory default value Click the Save button to save your settings Note Only the PC on your LAN can use the MAC Address Clone function 4 6 Wireless Wireless Wireless Security Wireless MAC Filtering Wireless Advanced Wireless Statistics Figure 4 15 Wireless menu There are five submenus under the Wireless menu shown in Figure 4 15 Wireless Settings Wireless Security Wireless MAC Filtering Wireless Advanced and Wireless Statistics Click any of them and you will be able to configure the corresponding function 29 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 6 1 Wireless Settings Choose menu Wireless Wireless Setting and then you can configure the basic settings for the wireless network on this page Wireless Settings SSID1 TP LIMk_E3C0860 SSID2 TP LIMk_E30860_2 SSID3 TP LINK E3C860_3 SSID TP LINK_ ESCoBO 4 Region United States Channel Auto w Mode 11bgn mixed Channel Width Auto w Enable Wireless Router Radio Enable SSID Broadcast C Enable WDS Save Figure 4 16 Wireless Settings gt SSID 1 4 Up to four SSIDs for each BSS Basic Service Set can be entered in the filed SSID1 SSID4 The name can be up
84. l Control Disable Enable MAC Address of Parental PC fe MAC Address of Your PC Copy To Above ID MAC address Website Description Schedule Add New Current Ho Page Figure 4 49 Parental Control Settings 58 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router To add a new entry please follow the steps below 1 Click the Add New button and the next screen will pop up as shown in Figure 4 50 Add or Modify Parental Control Entry The Schedule is based on the time ofthe Router The time can be setin System Tools gt Time settings MAC Address of Child PC All MAC Address In Current LAN please select we Website Description Allowed Domain Name IO NE Pp Pp PF Po Pp Pp Po Etective Time The time schedule can be setin Access Control Schedule Status Enabled w Figure 4 50 Add or Modify Parental Control Entry gt Parental Control Check Enable if you want this function to take effect otherwise check Disable gt MAC Address of Parental PC In this field enter the MAC address of the controlling PC or you can make use of the Copy To Above button below gt MAC Address of Your PC This field displays the MAC address of the PC that is managing this Router If the MAC Address of your adapter is registered you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above Website Description Description of
85. ll be reported when an active Internet service is successfully detected by the Router This report is for your reference only To make sure the connection type your ISP provides please refer to the ISP The various types of Internet connections that the Router can detect are as follows e PPPoE Connections which use PPPoE that requires a user name and password e Dynamic IP Connections which use dynamic IP address assignment e Static IP Connections which use static IP address assignment The Router can not detect PPTP L2TP BigPond connections with your ISP If your ISP uses one of these protocols then you must configure your connection manually 28 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 5 3 MAC Clone Choose menu Network MAC Clone and then you can configure the MAC address of the WAN on the screen below Figure 4 14 MAC Clone WAN MAC Address 00 08 01 00 00 05 Restore Factory MAC Your PC s MAC Address Clone MAC Address Figure 4 14 MAC Address Clone Some ISPs require that you register the MAC Address of your adapter Changes are rarely needed here gt WAN MAC Address This field displays the current MAC address of the WAN port If your ISP requires you to register the MAC address please enter the correct MAC address into this field in XX XX XX XX XX XX format X is any hexadecimal digit gt Your PC s MAC Address This field displays the MAC address of the PC that
86. lue is 0 You can input the value between 0 and 120 The value 0 means no detect gt DNS IP address If your ISP does not automatically assign DNS addresses to the Router during login please click Use the following DNS servers check box and enter the IP address in dotted decimal notation of your ISP s primary DNS server If a secondary DNS server address is available enter it as well Click the Save button to save your settings 4 lf your ISP provides BigPond Cable or Heart Beat Signal connection please select BigPond Cable And you should enter the following parameters Figure 4 11 WAN Connection Type Auth Server MTU Size in bytes 1500 The default is 1500 Do not change it unless necessary O Connect on Demand hax Idle Time is minutes 0 means remaining active all the time Connect Automatically O Connect Manually hax Idle Time s minutes 0 means remaining active all the time Connect Disconnected Save Figure 4 11 WAN BigPond Cable gt User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive gt Auth Server Enter the authenticating server IP address or host name gt Auth Domain Type in the domain suffix server name based on your location e g NSW ACT nsw bigpond net au VIC TAS WA SA NT vic bigpond net au QLD qld bigpond net au 24 TL WR720N 150Mbps Wireless N Router 50M
87. n Control Protocol internet Protocol The default wide area network protocol that provides communication actos diverse interconnected networks Show icon in notification area when connected M Notify me when this connection has limited or no connectivity Figure B 2 5 The following TCP IP Properties window will display and the IP Address tab is open on this wndow by default 97 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 6 Select Obtain an IP address automatically and Obtain DNS server automatically as shown in the Figure below Internet Protocol TCP IP Properties x General Alternate Configuration fou can get F settings assigned automatically if your network supports this capability Othenwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address Use the following ONS server addresses Prefered DNS server Alternate LHS server Figure B 3 98 TL WR720N METER EEE oTa Appendix C Specifications IEEE 802 3 IEEE 802 3u IEEE802 11n IEEE802 11b IEEE 802 11g TCP IP PPPoE DHCP ICMP NAT SNTP One 10 100M Auto Negotiation WAN RJ45 port Two 10 100M Auto Negotiation LAN RJ45 ports supporting Auto MDI MDIX Standards Protocols Ports 10BASE T UTP category 3 4 5 cable maximum 100m ElA TIA 568 1000 STP maximum 100m
88. n as you attempt to access the Internet again If you wish to activate Connect on Demand click the radio button If you want your Internet connection to remain active at all times enter 0 in the Max Idle Time field Otherwise enter the number of minutes you want to have elapsed before your Internet connection terminates gt Connect Automatically Connect automatically after the Router is disconnected To use this option click the radio button gt Connect Manually You can configure the Router to make it connect or disconnect manually After a specified period of inactivity Max Idle Time the Router will disconnect from your Internet connection and you will not be able to re establish your connection automatically as soon as you attempt to access the Internet again To use this option click the radio button If you want your Internet connection to remain active at all times enter 0 in the Max Idle Time field Otherwise enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested Caution Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time since some applications are visiting the Internet continually in the background E Note If you don t Know how to choose the appropriate connection type click the Detect button to allow the Router to automatically search your Internet connection for servers and protocols The connection type wi
89. n it accesses the DHCP server Reserved IP addresses should be assigned to the servers that require permanent IP settings Address Reservation MAC Address Reserved IP Address Status Modify 40 61 86 C4 08 43 192 168 0 100 Enabled Modify Delete Add New Enable All Disable All Delete All Figure 4 28 Address Reservation gt MAC Address The MAC address of the PC for which you want to reserve IP address gt Reserved IP Address The IP address of the Router reserved gt Status The status of this entry either Enabled or Disabled To Reserve IP addresses 1 Click the Add New button Pop up Figure 4 29 2 Enter the MAC address in XX XX XX XX XX XX format and IP address of the computer you wish to add in dotted decimal notation 3 Click the Save button when finished Add or Modify an Address Reservation Entry Reserved IP Address es Status Enabled Figure 4 29 Add or Modify an Address Reservation Entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete Modify the information Click the Save button 42 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Click the Enable Disable All button to make all entries enabled disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return to the previous page
90. ndards group promoting interoperability among 802 11b devices gt WLAN Wireless Local Area Network A group of computers and associated devices communicate with each other wirelessly which network serving users are limited in a local area 101
91. o load all items to the IP amp MAC Binding list Click the Refresh button to refresh all items Note An item could not be loaded to the IP amp MAC Binding list if the IP address of the item has been loaded before Error warning will prompt as well Likewise Load All only loads the items without interference to the IP amp MAC Binding list 4 15 Dynamic DNS The router offers a Dynamic Domain Name System DDNS feature DDNS lets you assign a fixed 76 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router host and domain name to a dynamic Internet IP Address It is useful when you are hosting your own website FTP server or other server behind the router Before using this feature you need to sign up for DDNS service providers such as www dyndns org The Dynamic DNS client service provider will give you a password or key To set up for DDNS follow these instructions 4 15 1 Comexe cn DDNS If your selected dynamic DNS Service Provider is www comexe cn the page will appear as shown in Figure 4 75 Service Provider Comexe www COMeXE Cr Goto register Domain Name Domain Name Domain Name Po PT PO Domain Name Po Po E Domain Name User Name Password Enable DONS Connection Status DONS not launching Save Figure 4 75 Comexe cn DDNS Settings To set up for DDNS follow these instructions 1 Type the Domain Name received from your dynamic DNS se
92. o return to the previous page Note If you set the service port of the virtual server as 80 you must set the Web management port on Security gt Remote Management page to be any other value except 80 such as 8080 Otherwise there will be a conflict to disable the virtual server 44 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 8 2 Port Triggering Choose menu Forwarding Port Triggering you can view and add port triggering in the next screen shown in Figure 4 33 Some applications require multiple connections like Internet games video conferencing Internet telephoning and so on Port Triggering is used for some of these applications that cannot work with a pure NAT Router Port Triggering ID Trigger Port Trigger Protocol Incoming Port Incoming Protocol Status Modify 1 554 ALL 0970 8999 ALL Enabled Modify Delete Add Mew Enable All Disable All Delete All Figure 4 33 Port Triggering To add a new rule follow the steps below 1 Click the Add New button the next screen will pop up as shown in Figure 4 34 2 Select a common application from the Common Applications drop down list then the Trigger Port field and the Incoming Ports field will be automatically filled If the Common Applications do not have the application you need enter the Trigger Port and the Incoming Ports manually 3 Select the protocol used for Trigger Port from the Trigger Protocol drop down list ei
93. ocated or operating in conjunction with any other antenna or transmitter CE Mark Warning 15880 This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures National restrictions This device is intended for home and office use in all EU countries and other countries following the EU directive 1999 5 EC without any limitation except for the countries mentioned below Country Restriction Reason remark General authorization required for outdoor use and Bulgaria None public service Outdoor use limited to 10 Military Radiolocation use Refarming of the 2 4 GHz France mW e i r p within the band band has been ongoing in recent years to allow current 2454 2483 5 MHz relaxed regulation Full implementation planned 2012 If used outside of own premises general authorization is Italy None required General authorization required for network and service Luxembourg None supply not for spectrum This subsection does not apply for the geographical area Norway Implemented within a radius of 20 km from the centre of Ny Alesund Russian Federation None Only for indoor applications Note Please don t use the product outdoors in France Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interfe
94. ollowing modes to enable security gt WEP Itis based on the IEEE 802 11 standard If you select this check box you will find a notice in red as show in Figure 4 18 Type WEP Key Format Key Selected Key 1 Key 2 Key 3 Key 4 WEP Key Key Type O LEE TO CO iat OoOo A OO i A We do not recommend using the WEP encryption ifthe device operates in 202 11n mode due to the factthat WEF is not supported by Orat 11M specification Figure 4 18 33 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router e Type you can choose the type for the WEP security on the drop down list The default setting is Automatic which can select Open System or Shared Key authentication type automatically based on the wireless station s capability and request e WEP Key Format Hexadecimal and ASCII formats are provided Hexadecimal format stands for any combination of hexadecimal digits 0 9 a f A F in the specified length ASCII format stands for any combination of keyboard characters in the specified length e WEP Key Select which of the four keys will be used and enter the matching WEP key that you create Make sure these values are identical on all wireless stations in your network e Key Type You can select the WEP key length 64 bit or 128 bit or 152 bit for encryption Disabled means this WEP key entry is invalid 64 bit You can enter 10 hexadecimal digits any combination of 0 9 a f A F
95. omain fs optional Primary DNS optional Secondary DNS optional Save Figure 4 26 DHCP Settings gt DHCP Server Enable or Disable the DHCP server If you disable the Server you must have another DHCP server within your network or else you must configure the computer manually gt Start IP Address Specify an IP address for the DHCP Server to start with when assigning IP addresses 192 168 0 100 is the default start address gt End IP Address Specify an IP address for the DHCP Server to end with when assigning IP 40 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router addresses 192 168 0 199 is the default end address gt Address Lease Time The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address Enter the amount of time in minutes and the user will be leased this dynamic IP Address After the time is up the user will be automatically assigned a new dynamic IP address The range of the time is 1 2880 minutes The default value is 120 minutes gt Default Gateway Optional Suggest to input the IP address of the LAN port of the Router default value is 192 168 0 1 gt Default Domain Optional Input the domain name of your network gt Primary DNS Optional Input the DNS IP address provided by your ISP Or consult your ISP gt Secondary DNS Optional Input the IP address of another DNS se
96. onnection please select L2TP Russia L2TP option And you should enter the following parameters Figure 4 12 25 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router WAN Connection Type User Name Password Server IF Address Name IP Address Subnet Mask Gateway DNS Internet IP Address Internet DNS L2TF Russia L2TP username 1 20000000 Disconnected DynamicIP Static IP 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 gt gt MTU Size in bytes The defaultis 1460 do not change unless necessary Max Idle Time minutes 0 means remain active at all times WAN Connection Mode Connecton Demand O Connect Automatically O Connect Manually Save Figure 4 12 WAN L2TP User Name Password Enter the User Name and Password provided by your ISP These fields are case sensitive Dynamic IP Static IP Choose either as you are given by your ISP Click the Connect button to connect immediately Click the Disconnect button to disconnect immediately Connect on Demand You can configure the Router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time If your Internet connection has been terminated due to inactivity Connect on Demand enables the Router to automatically re establish your connection as soon as you attempt to access the Int
97. ontent INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 INFO 2006 01 08 014 1 3JDHEPE Network config succeeded 08 01 11 PHEF client read totlen 6161040 06 01 11 OHCP client t request 06 017 11 DHCP client read totlen 6161040 08 00 36 Flags was changed to be 0x0 08 00 1 0J0AER client tx discover B De O0 06 DHCR client t discover B OS 00 04 DHCPS 1 0x406186cf20 a 192 168 0 100 ACK in request O6 00 03 DHCPS 1 084061 86ct20 a NAK in request 06 00 02 System The device initialization succeeded 1 INFO INFO 2006 04 01 08 00 02 noip O task sleep Time 2006 01 01 8 27 40 16615 H Ver WR720N 1 0 00000000 S Ver 4 19 44 Build 120331 ReL57077n L 192 168 0 1 M 255 255 255 0 W1 DHCP W 192 168 1 101 M 255 255 255 0 G 192 168 1 1 Free 5028 Busy 2 Bind 0 Im 0 3 Bc 0 15 Dns 98 cl 384 fc 0 0 sq 0 0 Figure 4 88 System Log gt Auto Mail Feature Indicates whether auto mail feature is enabled or not gt Mail Settings Set the receiving and sending mailbox address server address validation information as well as the timetable for Auto Mail Feature as shown in Figure 4 89 Mail Account Settings To SMTP Server L Authentication Enable Auto Mail Feature Everday mail the log at 18 00 Mail the log every 45 hours Figure 4 89 Mail Account Settings e From Your mail bo
98. ost Entry 67 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Add or Modify a Host Entry Mode MAC Address Host Description MAC Address 00 11 22 33 44 44 Figure 4 61 Add or Modify a Host Entry For example If you desire to restrict the internet activities of host with MAC address 00 11 22 33 44 AA you should first follow the settings below 1 Click Add New button in Figure 4 59 to enter the Add or Modify a Host Entry page 2 In Mode field select MAC Address from the drop down list 3 In Host Description field create a unique description for the host e g Host_1 4 In MAC Address field enter 00 1 1 22 33 44 AA 5 Click Save to complete the settings Then you will go back to the Host Settings page and see the following list ID Host Description information Modify 1 Host_1 MAC 00 11 22 33 44 AA Edit Delete 4 11 3 Target Choose menu Access Control Target and then you can view and set a Target list in the screen as shown in Figure 4 62 The target list is necessary for the Access Control Rule Target Settings ID Target Description Information Modify 1 Target 1 192 168 0 1 192 168 0 2 321 1 CF Edit Delete Add New Delete All Current No Page Figure 4 62 Target Settings gt Target Description Here displays the description about the target and this description is unique gt Information The target can be IP address port or domain name gt Mo
99. pull down list A Click the Save button to save it Add or Modify a Static Route Entry Destination IP Address Subnet Mask Default Gateway Status Enabled ld Figure 4 68 Add or Modify a Static Route Entry To modify or delete an existing entry 2 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete 2 Modify the information 3 Click the Save button Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled Click the Delete All button to delete all entries 4 13 IP QoS You can configure the IP QoS function on this page C Enable IP QoS Choose BandWidth Type Bandwidth Apply Kbps 5 IP Range Mode Bandwidth Description Enable Clear 192 168 0 192 168 0 192 168 0 192 168 0 192 168 0 192 168 0 E a a 192 168 0 192 168 0 192 168 0 192 168 0 192 168 0 192 168 0 a 192 168 0 192 168 0 1 2 3 4 5 6 T 8 192 168 0 TI 192 168 0 Figure 4 69 IP QoS gt Enable IP QoS Enable or disable the function of IP QoS gt Choose BandWidth Type Select the network connection type from the drop down list gt Bandwidth Apply The bandwidth you get If you are not clear about that please contact with your ISP for help gt IP Range IP range of this entry
100. ready listed in the drop down list of Incoming Protocol To modify or delete an existing entry 1 Find the desired entry in the table 2 Click Modify or Delete as desired on the Modify column Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled Click the Delete All button to delete all entries Once the Router is configured the operation is as follows 1 A local host makes an outgoing connection to an external host using a destination port number defined in the Trigger Port field 46 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 2 The Router records this connection opens the incoming port or ports associated with this entry in the Port Triggering table and associates them with the local host 3 When necessary the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field Note 1 When the trigger connection is released the corresponding opened ports will be closed 2 Each rule can only be used by one host on the LAN at a time The trigger connection of other hosts on the LAN will be refused 3 Incoming Ports ranges cannot overlap each other 4 8 3 DMZ Choose menu Forwarding DM2Z and then you can view and configure DMZ host in the screen shown in Figure 4 35 The DMZ host feature allows one local host to be exposed to the Internet for a special purpose servi
101. rence and 2 This device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 Le dispositif ne doit pas produire de brouillage pr judiciable et 2 Ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable NOTE IMPORTANTE Declaration d exposition aux radiations Cet equipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps Korea Warning Statements da FIA E 22 APEN HO QS NCC Notice STARS ERT RE AE SERRE AA RAE NADA E A AR MAI K BY Ses A et EE MINA o RIRI EL E A ME SR ER Hee MDA Teak BIE A We Die BART HE AO MAA TEM Te VAIL KE VE SZ PRR Te fo IRR a BSAA Se GZ LAR PEA OC ee CHIN TE Bs BD A PE o y MlpoaykT CepTUdiKOBaHO 3riaHo c npaBunamu cucrema YkpCENMNPO Ha BIAnoBiAaHic
102. rver if your ISP provides two DNS servers E Note To use the DHCP server function of the Router you must configure all computers on the LAN as Obtain an IP Address automatically mode 4 7 2 DHCP Clients List Choose menu DHCP DHCP Clients List and then you can view the information about the clients attached to the Router in the next screen shown in Figure 4 27 DHCP Clients List ID Client Name MAC Address Assigned IP Lease Time 1 tplink 419c5dd6 40 61 86 C4 98 43 192 168 0 100 01 49 12 Figure 4 27 DHCP Clients List gt ID The index of the DHCP Client gt Client Name The name of the DHCP client gt MAC Address The MAC address of the DHCP client gt Assigned IP The IP address that the Router has allocated to the DHCP client gt Lease Time The time of the DHCP client leased After the dynamic IP address has expired a new dynamic IP address will be automatically assigned to the user You cannot change any of the values on this page To update this page and to show the current attached devices click the Refresh button 41 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 7 3 Address Reservation Choose menu DHCP Address Reservation and then you can view and add a reserved address for clients via the next screen shown in Figure 4 28 When you specify a reserved IP address for a PC on the LAN that PC will always receive the same IP address each time whe
103. rvice provider 2 Type the User Name for your DDNS account 3 Type the Password for your DDNS account 4 Click the Login button to log in to the DDNS service Connection Status The status of the DDNS service connection is displayed here Click Logout to log out of the DDNS service 4 15 2 Dyndns org DDNS If your selected dynamic DNS Service Provider is www dyndns org the page will appear as shown in Figure 4 76 f TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router service Provider Dyndns www dyndns org Goto register C Enable DONS Connection Status DONS notlaunching Figure 4 76 Dyndns org DDNS Settings To set up for DDNS follow these instructions 1 Type the User Name for your DDNS account 2 Type the Password for your DDNS account 3 Type the Domain Name you received from dynamic DNS service provider here 4 Click the Login button to log in to the DDNS service Connection Status The status of the DDNS service connection is displayed here Click Logout to logout of the DDNS service 4 15 3 No ip com DDNS If the dynamic DNS Service Provider you select is www no ip com the page will appear as shown in Figure 4 77 Service Provider No lP f www nd ip corr 7 Go to register Enable DONS Connection Status DDNS not launching SAWE Figure 4 77 No ip com DDNS Settings 78 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router To set up for
104. ss Filtering entry Status Enabled w Figure 4 22 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry follow these instructions 1 Enter the appropriate MAC Address into the MAC Address field The format of the MAC Address iS XX XX XX XX XX XX X is any hexadecimal digit For example 00 0A EB 00 07 8A 2 Enter a simple description of the wireless station in the Description field For example 36 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Wireless station A 3 Select Enabled or Disabled for this entry on the Status drop down list 4 Click the Save button to save this entry To modify or delete an existing entry 1 Click the Modify in the entry you want to modify If you want to delete the entry click the Delete Modify the information Click the Save button Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled Click the Delete All button to delete all entries Click the Next button to go to the next page Click the Previous button to return to the previous page For example If you desire that the wireless station A with MAC address 00 OA EB 00 07 8A and the wireless station B with MAC address 00 OA EB 00 23 11 are able to access the Router but all the other wireless stations cannot access the Router you can configure the Wireless MAC Address Filtering list by following these steps
105. sure the wireless stations have right KEY for encryption when the Router is encrypted 4 Ifthe wireless connection is ready but you can t access the Router check the IP Address of your wireless stations 95 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Appendix B Configuring the PCs In this section we ll introduce how to install and configure the TCP IP correctly in Windows XP First make sure your Ethernet Adapter is working refer to the adapter s manual if needed 1 Install TCP IP component 1 On the Windows taskbar click the Start button point to Settings and then click Control Panel 2 Click the Network and Internet Connections icon and then click on the Network Connections tab in the appearing window 3 Right click the icon that showed below select Properties on the prompt page LAN or High Speed Internet ocal Area Connection Connected Firewalled Disable Status Repair Bridge Connections Create Shortcut Delete Rename Properties Figure B 1 96 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 4 Inthe prompt page that showed below double click on the Internet Protocol TCP IP Local Area Connection Properties l x General Authentication Advanced Connect using E Realtek ATL8139 Family PCI Fast Ett This connection uses the following tems r H lrstall Onmetal Properties Description Transmissio
106. ted Setup then you can press this button to quickly establish a connection between the Router and client devices and automatically configure wireless security for your wireless network gt POWER The Power socket is where you will connect the power adapter Please use the power adapter provided with this TL WR720N 150Mbps Wireless N Router gt WAN The WAN port is where you will connect the DSL cable Modem or Ethernet gt LAN 1 2 These ports connect the Router to the local PC s 5 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Chapter 2 Connecting the Router 2 1 System Requirements gt Broadband Internet Access Service DSL Cable Ethernet gt One DSL Cable Modem that has an RJ45 connector which is not necessary if the Router is connected directly to the Ethernet gt PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors gt TCP IP protocol on each PC gt Web browser such as Microsoft Internet Explorer 5 0 Netscape Navigator 6 0 or above 2 2 Installation Environment Requirements gt Place the Router in a well ventilated place far from any heater or heating vent gt Avoid direct irradiation of any strong light Such as sunlight gt Keep at least 2 inches 5 cm of clear space around the Router gt Operating Temperature 0 C 40 C 82 F 104 F gt Operating Humidity 10 90 RH Non condensing 2 3 Connecting the Router Before installing the Router
107. ter the MAC Address or IP Address 3 Click the Find button in the page as shown in Figure 4 73 Find IP amp MAC Binding Entry MAC Address 00 14 5E 61 150 E3 ID MAC Address IP Address Bind Link 2 O0 14 5E 91 19 E3 192 168 056 To page 75 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Figure 4 73 Find IP amp MAC Binding Entry Click the Enable All button to make all entries enabled Click the Delete All button to delete all entries 4 14 2 ARP List To manage the computer you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list and you could also configure the items on the ARP list This page displays the ARP List it shows all the existing IP amp MAC Binding entries shown in Figure 4 74 ARP List MAC Address IP Address Status Configure 40 61 86 C4 98 43 192 168 0 100 Bound Load Delete 40 61 86 C4 98 42 192 168 0 101 Bound Load Delete Bind All Load All Figure 4 74 ARP List 1 MAC Address The MAC address of the controlled computer in the LAN 2 IP Address The assigned IP address of the controlled computer in the LAN 3 Status Indicates whether or not the MAC and IP addresses are bound 4 Configure Load or delete an item gt Load Load the item to the IP amp MAC Binding list gt Delete Delete the item Click the Bind All button to bind all the current items available after enable Click the Load All button t
108. the Router will automatically detect the connection type your ISP provides Make sure the cable is securely plugged into the WAN port before detection The appropriate configuration page will be displayed when an active Internet service is successfully detected by the Router gt If the connection type detected is PPPoE the next screen will appear as shown in Figure 3 7 Quick Setup PPPoE User Name username Figure 3 7 Quick Setup PPPoE gt User Name and Password Enter the User Name and Password provided by your ISP These fields are case sensitive If you have difficulty with this process please contact your ISP gt Confirm Password Re enter the password provided by your ISP to ensure the Password you entered is correct If the Password is different from the Confirm Password the screen will appear as shown below Click OK and re enter the Password and Confirm Password TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Microsoft Internet Explorer A The Password is different from the Confirm Password gt Ifthe connection type detected is Dynamic IP the next screen will appear as shown in Figure 3 9 gt If the connection type detected is Static IP the next screen will appear as shown in Figure 3 8 Quick Setup Static IP IP Address 0 0 0 0 Subnet Mask 0 0 0 Default Gateway 0 0 0 0 Optional Primary DHS 0000 Optional Secondary DHS 0 0 0 0 Optional Figure
109. the allowed website for the PC controlled gt Schedule The time period allowed for the PC controlled to access the Internet For detailed information please go to Access Control Schedule gt Enable Check this option to enable a specific entry gt Modify Here you can edit or delete an existing entry 2 Enter the MAC address of the PC e g 00 11 22 33 44 AA you d like to control in the MAC Address of Child PC field or you can choose the MAC address from the All Address in Current LAN drop down list 59 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 3 Give a description e g Allow Google for the website allowed to be accessed in the Website Description field 4 Enter the allowed domain name of the website either the full name or the keywords e g google in the Allowed Domain Name field Any domain name with keywords in it www google com www google com hk will be allowed 5 Select from the Effective Time drop down list the schedule e g Schedule_1 you want If there are not suitable schedules for you click the Schedule in red below to go to the Advance Schedule Settings page and create the schedule you need 6 Inthe Status field you can select Enabled or Disabled to enable or disable your entry 7 Click the Save button Click the Enable All button to enable all the rules in the list Click the Disable All button to disable all the rules in the list Click the Delete All button
110. the logs in a txt file Vv Vv VY V WV Mail Log Click to send an email of current logs manually according to the address and validation information set in Mail Settings gt Clear Log All the logs will be deleted from the Router permanently not just from the page Click the Next button to go to the next page or click the Previous button to return to the previous page 4 16 9 Statistics Choose menu System Tools Statistics and then you can view the statistics of the Router including total traffic and current traffic of the last Packets Statistic Interval 88 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Statistics Current Statistics Status Disabled Packets Statistics Interval 5 60 10 Seconds Auto retreshi Sorted Rules sorted by IP Address he Reset All Delete All Total Current Modify IP Address MAC Address Packets Bytes Packets Bytes ICMP Tx UDP Tx SYN Tx The current listis empty entries per page Current No page Figure 4 90 Statistics gt Current Statistics Status Enable or Disable The default value is disabled To enable it click the Enable button If it is disabled the function of DoS protection in Security settings will be disabled gt Packets Statistics Interval 5 60 The default value is 10 Select a value between 5 and 60 seconds in the drop down list The Packets Statistic interval indicates the time section of the packets statistic gt Sort
111. ther TCP UDP or All 4 Select the protocol used for Incoming Ports from the Incoming Protocol drop down list either TCP or UDP or All 5 Select Enable in Status field 6 Click the Save button to save the new rule 45 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Add or Modify a Port Triggering Entry Trigger Port Trigger Protocol Incoming Ports Incoming Protocol ALL ow Status Enabled Common Applications Select One Figure 4 34 Add or Modify a Triggering Entry gt Trigger Port The port for outgoing traffic An outgoing connection using this port will trigger this rule gt Trigger Protocol The protocol used for Trigger Ports either TCP UDP or All all protocols supported by the Router gt Incoming Ports The port or port range used by the remote system when it responds to the outgoing request A response using one of these ports will be forwarded to the PC which triggered this rule You can input at most 5 groups of ports or port sections Every group of ports must be separated with for example 2000 2038 2046 2050 2051 2085 3010 3030 gt Incoming Protocol The protocol used for Incoming Port either TCP UDP or ALL all protocols supported by the Router gt Status The status of this entry Enabled means the Port Triggering entry is enabled gt Modify To modify or delete an existing entry gt Common Applications Some popular applications al
112. tion in Navigator box followed by a colon and the custom port number For example if your Router s WAN address is 202 96 12 8 and the port number used is 8080 please enter http 202 96 12 8 8080 in your browser Later you may be asked for the Router s password After successfully entering the username and password you will be able to access the Router s web based utility 2 Be sure to change the Router s default password to a very secure password 4 9 7 Advanced Security Using Advanced Security page you can protect the router from being attacked by TCP SYN Flood UDP Flood and ICMP Flood from LAN 56 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Advanced Security Packets Statistics Interval 5 60 Seconds Dos Protection Disable O Enable Enable OMP FLOOD Attack Filtering ICMP FLOOD Packets Threshold 5 3600 so Packets s Enable DOP FLOGD Filtering UDP FLOOD Packets Threshold 5 3600 soo Packets s Enable TOP SYM FLOOD Attack Filtering TCP SYN FLOOD Packets Threshold 5 3600 so Packetsls Ignore Ping Packet From WAN Port Forbid Ping Packet From LAM Por Blocked Dos Host List Figure 4 47 Advanced Security settings gt Packets Statistic interval 5 60 The default value is 10 Select a value between 5 and 60 seconds in the pull down list The Packets Statistic interval value indicates the time section of the packets statistic The result of the statistic used
113. ton on the back panel for at least 5 seconds to reset the Router s factory defaults on the Router s Web Based Utility 4 9 6 Remote Management Choose menu Security Remote Management and then you can configure the Remote Management function in the screen as shown in Figure 4 46 This feature allows you to manage your Router from a remote location via the Internet 55 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Remote Management Web Management Port Remote Management IP Address 0 0 0 0 Enter 255 255 255 255 for alli Dave Figure 4 46 Remote Management gt Web Management Port Web browser access normally uses the standard HTTP service port 80 This Router s default remote management web port number is 80 For greater security you can change the remote management web port to a custom port by entering that number in the box provided Choose a number between 1 and 65534 but do not use the number of any common service port gt Remote Management IP Address This is the current address you will use when accessing your Router from the Internet This function is disabled when the IP address is set to the default value of 0 0 0 0 To enable this function change 0 0 0 0 to a valid IP address If set to 255 255 255 255 then all the hosts can access the Router from internet E Note 1 To access the Router you should type your Router s WAN IP address into your browser s address in IE or Loca
114. u specify a time to Max Idle Time since some applications are visiting the Internet continually in the background If you want to do some advanced configurations please click the Advanced button and the page shown in Figure 4 10 will then appear PPPoE Advanced Settings MTU Size in bytes 1480 The defaultis 1480 do not change unless necessary C Use IP address specified by ISP ISP Specified IP Address ooon Detect Online Interval lo Seconds 0 120 seconds the default is 0 0 means not detecting C Use the following DNS Servers Secondary DNS ooon Optional Figure 4 10 PPPoE Advanced Settings gt MTU Size The default MTU size is 1480 bytes which is usually fine It is not recommended that you change the default MTU Size unless required by your ISP gt Service Name AC Name The service name and AC Access Concentrator name which should not be configured unless you are sure it is necessary for your ISP In most cases leaving these fields blank will work gt ISP Specified IP Address If your ISP does not automatically assign IP addresses to the Router during login please click Use IP address specified by ISP check box and enter the IP address provided by your ISP in dotted decimal notation gt Detect Online Interval The Router will detect Access Concentrator online at every interval 22 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router The default va
115. up of any numbers from 0 to 9 and any letters from A to Z and the length should be between 8 and 63 characters For Hexadecimal the key can be made up of any numbers from 0 to 9 and letters from A to F and the length should be between 8 and 64 characters Please also note the key is case sensitive which means that upper and lower case keys will affect the outcome It would also be a good idea to write down the key and all related wireless security settings gt No Change If you choose this option wireless security configuration will not change These settings are only for basic wireless parameters For advanced settings please refer to Section 4 6 Wireless 6 Click the Next button You will then see the Finish page If you don t make any changes on the Wireless page you will see the Finish page as shown in Figure 3 10 Click the Finish button to finish the Quick Setup Quick Setup Finish Congratulations The Router is now connecting you to the Internet For detail settings please click other menus if necessary Figure 3 10 Quick Setup Finish If there is something changed on the Wireless page you will see the Finish page as shown in Figure 3 11 Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup Quick Setup Finish Congratulations The Router is now connecting you to the Internet For detail settings please click other menus if necessary T
116. users supporting Dynamic IP Static IP PPPoE Internet access gt Upto 4 SSIDs supporting multiple wireless networks with different SSIDs and passwords gt Supports Virtual Server Special Application and DMZ host gt Supports UPnP Dynamic DNS gt Provides Automatic connection and Scheduled Connection on certain time to the Internet gt Connects Internet on demand and disconnects from the Internet when idle for PPPoE gt Built in NAT and DHCP server supporting static IP address distributing gt Supports Stateful Packet Inspection gt Supports Parental Control and Access Control gt Provides 64 128 152 bit WEP encryption security and wireless LAN ACL Access Control List gt Supports Flow Statistics gt Supports firmware upgrade and Web management sas TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 1 4 Panel Layout 1 4 1 The Front Panel 06 gt 090048 Figure 1 1 Front Panel sketch The Router s LEDs and the WPS button are located on the front panel View from left to right pe e e a a aooo EZ The Router is oO properly System On Off Off The Router has a system error Pa Of The Wireless function is disabled gt WLAN The Wireless function is enabled There is no device linked to the corresponding port a LAN1 2 On There is a device linked to the corresponding port but WAN there is no activity Flashing There is an active device linked to the corresponding port
117. utomatically Time based Connecting Period of Time fram la o HH to 23 59 HH Connect Manually hax Idle Time 15 minutes 0 means remain active at all times Disconnected Figure A 2 PPPoE Connection Mode E Note i Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time since some applications is visiting the Internet continually in the background ii If you are a Cable user please configure the Router following the above steps 91 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router 2 How do I configure the Router to access Internet by Ethernet users 1 Login to the Router click the Network menu on the left of your browser and click WAN submenu On the WAN page select Dynamic IP for WAN Connection Type finish by clicking Save 2 Some ISPs require that you register the MAC Address of your adapter which is connected to your cable DSL Modem during installation If your ISP requires MAC register login to the Router and click the Network menu link on the left of your browser and then click MAC Clone submenu link On the MAC Clone page if your PC s MAC address is proper MAC address click the Clone MAC Address button and your PC s MAC address will fill in the WAN MAC Address field Or else type the MAC Address into the WAN MAC Address field The format for the MAC Address is XX XX XX XX XX XX Then
118. will take effect Select Disable so that the rule won t take effect 5 Click Finish to complete adding a new rule Method Two 1 Click the Add New button and the next screen will pop up as shown in Figure 4 58 Give a name e g Rule_1 for the rule in the Rule Name field Select a host from the Host drop down list or choose Click Here To Add New Host List gt 0 N Select a target from the Target drop sown list or choose Click Here To Add New Target List 5 Select a schedule from the Schedule drop down list or choose Click Here To Add New Schedule 6 Inthe Status field select Enabled or Disabled to enable or disable your entry 7 Click the Save button 65 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router Add Internet Access Control Entry Rule Name Host Click Here To Add Mew Host List Target Any Target Click Here To Add New Target List Schedule Anytime Click Here To Add New Schedule Status Enabled Figure 4 58 Add Internet Access Control Entry For example If you desire to allow the host with MAC address 00 11 22 33 44 AA to access www google com only from 18 00 to 20 00 on Saturday and Sunday and forbid other hosts in the LAN to access the Internet you should follow the settings below 1 Click the submenu Rule of Access Control in the left to return to the Rule List page Select Enable Internet Access Control and choose Allow the packets specified
119. x address The Router would connect it to send logs e To Recipient s address The destination mailbox where the logs would be received e SMTP Server Your smtp server It corresponds with the mailbox filled in the From field 87 TL WR720N 150Mbps Wireless N Router 50Mbps Wireless N Router You can log on the relevant website for help if you are not clear with the address e Authentication Most SMTP Server requires Authentication It is required by most mailboxes that need User Name and Password to log in 5 Note Only when you select Authentication do you have to enter the User Name and Password in the following fields e User Name Your mail account name filled in the From field The part behind is excluded e Password Your mail account password e Confirm The Password Enter the password again to confirm e Enable Auto Mail Feature Select it to mail logs automatically You could mail the current logs either at a specified time everyday or by intervals but only one could be the current effective rule Enter the desired time or intervals in the corresponding field as shown in Figure 4 89 Click Save to keep your settings Click Back to return to the previous page Log Type By selecting the log type only logs of this type will be shown Log Level By selecting the log level only logs of this level will be shown Refresh Refresh the page to show the latest log list Save Log Click to save all

TP-Link 150Mbs User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents