TOA Electronics TA 1400 User's Manual
Contents
1. are in red desired output power see MLS table load impedance and the selected maximum gain The sensitivity is in the box labeled Input level for clip in Vrms or dBu 5 13 Options As the DIP switch is recessed one can put a sticker across the bay and prevent from unauthorized changes Another option is to remove the DIP switch This should be done by authorized service personnel only This corresponds to all switches set to off i e 32dB gain and stereo mode Tannoy Limited 6 TA 1400 User Manual 11 06 02 5 2 Link switch The Link switch located on the rear panel the central DIP switch is for changing the operation mode of the amplifier see below section 5 3 5 3 Operation modes LINK BRIDGE A B NK BR SENS 5 3 1 Stereo mode In this mode both channels operate independently of each other This is mrn used for all 2 channel modes such as stereo and bi amping Set the two center switches to off position for the stereo mode The level attenuators LU E on the front panel will control the respective channels levels 12345678 Never connect either output terminal to ground or in parallel The STEREO h recommended minimum nominal impedance for stereo or tandem operation is 2 ohms per channel 5 3 2 Note for bench test A NOTE Channel B is always polarity reversed on the input but polarity compensated by Y feeding the minus pin on the Channel2. e Fuses on the supply branches of each channel e ADC crowbar protection that shorts the output if more than 10 volts DC are being detected on the outputs Both these circuits come into effect once a DC level are beeing detected on either channel 10 MAINTENANCE Under normal use the amplifier should provide years of trouble free service The only user maintenance required by the user is to vacuum the front grill periodically In some extreme cases it may be necessary for authorized service personnel to clean the inside of the amplifier These conditions usually occur after prolonged use e g in environments using cracked oil smoke machines If you are using your amplifier for heavy duty use i e concert touring or industrial music it is recommended that you have your amplifier serviced every 3 years purely as a preventative measure 10 1 Troubleshooting These are typical things to check if you think your amplifier is faulty Fault No output If the Signal Present 40dB is illuminating there is nothing wrong with the amplifier the likely cause is an unsecured Speakon speaker connector Check also that the VHF protection is not activated If it is remove possible high frequency oscillations from the relevant input Fault The amplifier goes into thermal protection when driven at low level Check that nothing causes a short circuit at the amplifier s output e g any component in the loudspeaker this can occur when the spea
3. it locks in place and prevents from shock hazard They are wired in the following manner The right jack Channel A has both channel A and B outputs so it s useful for bridging and bi amp operation see bridged mono operation on page 7 The left Speakon Channel B carries only the channel B output El Aud TE ani Channel A and B into two Channel A and B into one Bridged mono separate Speakons Speakon Stereo and Bi amp Never connect either output terminal to ground or to some other output or input terminal see warnings in chapter 1 For normal two channel operation connect each speaker load across the output s positive and negative terminals Pay attention to speaker polarity loudspeakers connected out of polarity degrade sound quality and may be damaged as a consequence Keep the speaker cable wires as short as possible and use a good quality stranded speaker cable Do not use shielded wire such as microphone or guitar cable Remember that the speaker cable robs the power of the amplifiers in two ways Increases the load impedance and introduces resistive power losses A WARNING To prevent from electric shock do not operate the amplifier with any of the conductor portion of the speaker wire exposed 8 OPERATION 8 1 Operation precautions e Make sure that the power switch is set to off before co
4. Electrical Safety EN60065 Class 3 1 Explanation of graphical symbols y The lightning symbol within a triangle Y is intended to alert the user to the presence of un insulated dangerous voltage within the amplifier s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans The exclamation point within a triangle e is intended to alert the user to presence of important operating and service instructions in the literature accompanying the product 3 2 WARNING To reduce risk of fire or electric shock do not 3 3 CAUTION To reduce the risk of fire or electric shock do not remove screws No user serviceable expose this apparatus to rain or moisture 7 parts inside Refer servicing to qualified service personnel 3 4 Important Safety Instructions Before using your amplifier be sure to carefully read the applicable items of these operating instructions and the safety suggestions 1 Keep this manual for future reference 2 Heed all warnings 3 Follow all instructions 4 Do not use this unit near water Do not spill water or other liquids into or on the unit Do not operate the amplifier while wet or standing in liquid 5 Clean only with dry cloth 6 Do not block the air intake or exhaust ports Install the unit in accordance with the instructions 7 Do not operate the amplifier near heat producing devices such as radiators heat
5. daisy chain amplifiers use the screw terminal Phoenix connector labeled Link provided on each TAO KQ channel It is connected in parallel with the Neutrik Combo jack on each input U 7 1 2 Unbalanced inputs To connect an unbalanced source tie pin 3 ring on TRS jack down to the shield of the connector If you leave one pin disconnected you will lose 6 dB A better method for using unbalanced sources is shown in Figure 8 This is similar to the connection for balanced lines but pin 3 is connected to the shield at the source The hum and noise rejection for the cable is equivalent to that for a balanced line To minimize hum in the audio use balanced inputs whenever possible Figure 7 Unbalanced line connection Figure 8 Balanced line with unbalanced equipment n ET H i Ng ms O gt J As SS po MPLIFIER gal For two channel stereo operation use both channels A and B For tandem stereo or bridged mono operation use only one of the inputs See operation modes for more details Tannoy Limited 11 TA 1400 User Manual 11 06 02 7 2 Connecting speakers Speaker connections are made via the two Neutrik NL4FC Speakon connectors The Speakon connector is designed for high power speaker connections It assures the correct polarity
6. registers stoves or other apparatus that produce heat 8 Always operate the unit with the chassis ground wire connected to the electrical safety earth Do not defeat the safety purpose of a grounding type plug A grounding type plug has two pins and a third grounding prong The third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 9 Connect only to AC power outlets rated 230 240V or 100 120V 50 60Hz Tannoy Limited 2 TA 1400 User Manual 11 06 02 10 Do not use this amplifier if the power cord is broken or frayed Protect the power cord from being walked upon or pinched particularly at the plugs and the point where it exits from the apparatus 11 Only use accessories specified by the manufacturer 12 The unit is intended to use in a 19 rack Follow the mounting instructions When a rack on wheels is used use caution when moving the loaded rack to avoid injury from tipping over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Do not connect an amplifier output in parallel or series with any other amplifier s output Do not connect the amplifier output to any other voltage source such as battery mains source or power supply regardless of whether the amplifier is turned on or off 15 Do not run the output of any amplifier back into another channel s input 16 Refer all servic
7. removable for easy cleaning of the filter by simply pulling them off The foam filter should always be used 8 Carry protection handle Both handles can be used to carry the amplifier they also act as protection for the front panel In fixed installations or where rack front covers are too shallow they may be removed by unscrewing the retaining bolts behind the front panel 4 3 Rear Panel 4 2 A O Q et cH la INPUT ome Si a LR ae 2 Po d 508 TANNOY pista scons oa E CON E 9 Figure 2 Rear Panel 1 Output Speaker connector The Speakon connector from Neutrik may be unfamiliar to some users A full description is found in the operation section See page 12 3 Clip limiter switch Turns the clip limiter on switch IN position or off switch OUT position See page 13 4 Input signal XLR Neutrik Combojack features also 1 4 TRS phone jacks Pin 2 is hot see page 10 5 Link Output 3 pole screw terminal of Phoenix brand Connected in parallel to the female XLR input connector for linking the channel to another input 6 Gain switch channel B Three of the switches in the DIP switch selects the maximum gain of the channel to be either 20 23 26 29 32 36 39 or 41 dB See page 6 7 Link and Polarity reverse switch Two of the switches in the DIP switch are used for Link and Bridge operation Se
8. A 1400 User Manual 11 06 02 6 3 Operating voltage WARNING A A label just below the mains cable on the rear of the amplifier indicates the AC mains voltage for which the amplifier is wired Connect the power cable only to the AC source referred to on the label The warranty will not cover damage caused by connecting to the wrong type of AC mains If the power plug is not appropriate for your country it can be cut off and wired to a suitable connector in the following way BLACK or BROWN LIVE WHITE or BLUE NEUTRAL GREEN or GREEN YELLOW EARTH Once the AC connector is connected to a suitable AC supply the amplifier can be started with the power switch When you power up the amplifier it takes a couple of seconds to check its circuits this is known as the soft start or slow start sequence the fans then blow at high speed before going into idle and the two bottom green LED s come on to show the output circuits are receiving the correct rail voltage 6 4 Denmark National deviation concerning installation of the TA 1400 Danish safety regulation only permits 8A main fuse As the TA 1400 use an internal primary mains fuse of 15A TA 1400 must be equipped with an industrial mains connector rated for 16A or as an alternative be fixed installed to a 16A circuit 6 5 Switzerland National deviation concerning installation of the TA 1400 Swiss safety regulation stipulates that mains connector of the type 23 mu
9. B output with the output voltage Channel A output is a connected in normal polarity mode By having channel A and B operating in opposite Belay the energy storage in the power supply is more efficient This is significant for signals below 100 Hz sub bass etc and improves the power bandwidth Be sure to use balanced inputs on all measurement equipment also oscilloscope probes if you are bench testing SET opa 99 i INPUT BUFFERS POHER AMP SPEAKERS CH B T N Reverse operation of Channel B 5 3 3 Tandem mode In tandem mode both channels inputs are linked and receive the same signal The tandem mode is active if the Link switches are in position On Both level attenuators are active allowing you to set different levels for each channel Note that only the inputs are connected in parallel This is NOT a parallel output mode Never connect either output terminal to ground or in parallel You can use the remaining input connectors to carry signal to other amps This is called Daisy chaining NOTE Always turn off the Link switch when using the amplifier for Bi amping 5 3 4 Bridge mono mode Bridge mono mode is used to deliver both channels power to a single load The nominal impedance of the load must be more than 3 ohms Set the Link switches to the On position and use one of the input connectors You can use the remaining input connectors to carry signal to other amps Both level att
10. CONNECTIONS css ada E Tin 10 7 1 INPUE CONNECHONS 0 ccsicseteisccatectasccceadcsexchecachecaaveeiagcnlasiecaddelantacensigeaseecagncsdateaiedeghedeates 10 7 1 1 Balanced input ida 10 7 1 2 Unbalanced INPUTS ricota ra a 11 7 2 Connecting speakerS iii da AA A dt AAA 12 8 OPERATION envasar a a a a a aa aa aaea D dad 12 8 1 Operation precautiONS oooconicinnicnnninniccnncnnncnnnnnnn rn 12 8 2 Powering up Oia torta 13 83 ppu ataO Sii A a Rana 13 DA MGICAOMS tii AA AA A A A A AS 13 9 PROTECTION FEATURES viii A ae ae 13 9 1 1 Clip Li rain ad 13 9 1 2 Thermal protectiON occccccnnccnnncnncnnnnnnnnnnnnnonnnnnnnnnnnnnnnnnnnnnnonnnnnnnnnnnonnnonenoneneness 14 9 13 MARE PrOtecliOnss scescs cesestocsladscczscicacdsta cue cxisecasaccedtsdiazscdetecdetesgereoactsenatsheadebautadieias 14 9 1 4 Short Circuit Protection sser elana nan ea r aa eK ar a AE ae Ee AE ARSA NE ERARE AENEASE 14 9 1 5 AC mains voltage proteccion ie e 14 9 1 6 DC protection doc dai 14 10 MAINTENANCE E Wee dicas 14 TOT TPOUDIGS TALO nia aiii falcon ie cocos 14 11 WARRANTY Ai 15 Tannoy ET TA 1400 User Manual 11 06 02 2 APPROVALS amended by 92 31 EEC and 93 68 EEC and the requirements of the Low Voltage C This equipment conforms to the requirements of the EMC directive 89 336 EEC Directive 73 23 EEC amended by 93 68 EEC Standard Applied EMC Emission EN55103 1 E3 EMC Immunity EN55103 2 E3 with S N below 1 at normal operation level
11. TA 1400 USER MANUAL 1 CONTENTS Tis CONTENER A A seais 1 2 APPROVA Sia 2 3 WARNINGS iii a aaa iii 2 3 1 Explanation of graphical symbols actora ancora orinal lapidan 2 32 AVARNIN Gotta a a Sin a eee altar Mate A EE 2 BS CAUTION arniran E r e e 2 3 4 Important Safety Instructions acortan tits 2 3 5 User responsibilty ci e anda 3 3 5 1 Speaker damage cian docto aa aaa T a ra A Ea aia tanisa 3 3 5 2 Speaker output hazard ooooooccnncccccccicccocncnnennnnnnnnnnnnnnnnnnnnnnonnnonnnnnnnnnnnnnnnnninnninnninnness 3 3 5 3 Radio interference macia a a a S 3 A INTRODUCTION stc a A A A AAA 4 DN o O 4 O 4 A lO oa tesaents 5 REAR PANEL FEATURES td aladas 6 Ord Gas Will asados 6 5 1 1 The DIP SWitCO oi a A ia 6 5 1 2 SONS isis taa a ea ek basihan 6 5 1 3 OP IONS cio E E EE 6 A E A O AAA E T TA 7 53 Operation MOS cui ed 7 5 3 1 Stere ModE ist dadas 7 5 3 2 Note for bench testone iaaa cnc 7 5 3 3 Tandem MOC ier eee ea arean e aan O aeea aa aa E ara aa aa chaavecenscectencenes 7 5 3 4 Bridge MOnO MOE susan aaa iaai a aa ti n 7 5 3 5 Bridge mono mode features cc cccceceeeeeeeeeeenceeeeeeeeeesesecceeeeceeeeseeseestenseneeeeeees 8 6 INSTALLATION is ay ee a RAM aaa ee lta eres 8 6 1 MOUNT ede eco 8 0 2 CODINA it e 8 6 3 Operating VONAGC i senseri iagetwexndua fi 9 O aa TE 1 TEE A 9 ESES AT 110 cial E A A EEA EETA TTT EAT 9 AN A O TE Salar 9 6 7 Power CONSUMPTION iii A AAA A A 9 6 7 1 Calcula ii alias 10 F
12. ation number on the outside of the packing 4 Ship the product prepaid to Tannoy Limited Rosehall Industrial Estate Coatbridge ML5 4TF Tel 44 01236 420 199 Fax 44 01236 428 230 www tannoy com Tannoy Limited 15 TA 1400 User Manual 11 06 02
13. crossover units In an actively 1 divided system there is very often a so called loudspeaker 2345678 processor or controller involved being unique for the loudspeaker y system In most cases the manufacturers of these processors mm and or loudspeakers recommend a specific system gain for the amplifiers There are eight positions with different gain from 20dB to 41dB in 3dB steps See the different settings for the DIP switches in the table below The three switches to the very left are for channel B and the three to the very right are for channel A GAIN 123 5 1 2 Sensitivity 200B A Eon 23dB LF orr Sensitivity is defined as how many volts rms or dBu referred to 26dBlel 0 775Vrms are required to get full output power As the output power rl varies with the load impedance usually 4 ohms is the reference But in 29dB case of an MLS switch equipped amplifier there are enough choices for full 32dBlelelsl output levels into different load impedances for a sensitivity table to fill 35dB les several pages 38dB eF Hence we recommend calculating the sensitivity if this is necessary Our Audio calculator can do this which is an Excel file with many useful 41dB EF formulas It contains help for setting up digital loudspeaker processors and 678 can be found on our website www tannoy com The sensitivity calculator is found in the box labeled Amplifier gain conversions The values to enter
14. e if any protection circuits are activated O protect C These are described on page 13 cue The Clip limit indicator tells when the A0dB O amplifier output is clipping or limiting It EN O has two different indication statuses e Ifthe clip limiter is engaged it has a Me 7 Ag d short time constant and it w 1 a 6 ls illuminates briefly 2 3 eee CD ae e If the clip limiter is not engaged it ae fs mg Figs as has an increased time constant ad ao TA 1400 sd as and it illuminates for a longer AS ae ka period Front Indicators The 40 dB LED s illuminate if the output signal is greater than 40dB with OdB as reference to full output power These LED s also act as signal present indicators The two bottom green ON LED s indicate that the output circuits are receiving the correct rail voltage 9 PROTECTION FEATURES Each Tannoy amplifier has many advanced protection features protecting both the amplifier and the speakers connected to it should a fault condition arise Under normal use these features are inaudible All protection circuits are independent 9 1 1 Clip Limiter The clip limiter is included to prevent dangerous clipped signals reaching the speaker and damaging it When an amplifier is severely overdriven its output waveform is clipped its peaks are squared off reducing the crest factor In extreme cases the waveform can approach that of a square wave An amplif
15. e page 6 Tannoy Limited 5 TA 1400 User Manual 11 06 02 8 Gain switch channel A Three of the switches in the DIP switch selects the maximum gain of the channel to be either 20 23 26 29 32 36 39 or 41 dB See page 6 9 AC power cable WARNING A label just below the mains cable on the rear of the amplifier indicates the AC mains voltage for which the amplifier is wired Connect the power cable only to the AC source referred to on the label 5 REAR PANEL FEATURES 5 1 Gain switch The gain switch located on the rear panel the central DIP switch changes the input sensitivity of the amplifier This can be handy when using low or high nominal input signals E g most professional mixing consoles operate at a nominal level of 4 to 6 dBu therefore you may use the 32dB position to provide you with plenty of fader movement On the other hand for a disco mixer operating at a nominal level of OdBu or less use the higher gain positions 5 1 1 The DIP switch There are separate sections for the two channels so different gain A TR can be selected for channel A or B The selection of maximum gain GAIN GAIN in the amplifier is always a trade between noise and headroom A CH B CH A low gain amplifier amplifies less of the noise of the preceding i a a equipment mixer crossover equalizer etc On the other hand a higher lever is needed to get full power so the headroom will be UW UW UW UW UW E decreased on mixer output and or
16. enuators must be at the same position We recommend that you put them in the OdB full position Connect the speaker as shown Always use Channel A s output connector wz N SS 17 O NAS Z NINS H a TA 1400 User Manual 11 06 02 5 3 5 Bridge mono mode features Bridged mono mode combines the power of both channels into one speaker This results in twice the voltage swing four times the peak power and just less than three times the full power of a single channel One way to understand the load and power from the amplifier s perspective in bridged mode is that it is zero voltage at the center of the voice coil winding This is because the coil is driven with positive voltage at one pole and an equivalent negative voltage at the other pole So if an 8 onms load is connected in bridged mode one channel shares one 4 ohms part of the load and the other channel shares the other 4 ohms part The power into 4 ohms from an TA 1200 is 700W So the total bridged power into the 8 ohms load will be 2 x 700 1400W Bl a 0 LINK A 00 00 INPUT BUFFERS gt POWER AMP 1 SPEAKER CH B E y x o P 2 D pas 6 INSTALLATION 6 1 Mounting The amplifier is two rack units high 2U and will mount in a standard EIA 19 rack Amplifiers may be stacked directly on top of each other There is no need for spacing between units If it is the intention to fill a rack with ampli
17. es and radio interference e Consult the dealer or an experienced radio TV technician for help 4 INTRODUCTION Thank you for purchasing a TANNOY power amplifier This manual contains important information on operating your amplifier correctly and safely Please take some time and read this manual to familiarize you with the advanced features of this amplifier 4 1 Unpacking Carefully open the shipping carton and check for any noticeable damage Every Tannoy amplifier is tested and inspected before leaving the factory and should arrive in perfect condition If found to be damaged notify the shipping company immediately Only the consignee may institute a claim with the carrier for damage incurred during shipping Be sure to save the carton and packing materials for the carrier s inspection It is also advisable to save the carton and packing material even if the amplifier is undamaged Should you ever need to ship the amplifier always use the original packing i _ 4 2 Front Panel a Sat Mo N ve TA 1400 AS Figure 1 front panel 1 Input level attenuators These controls are used to alter the signal level entering the amplifier They are calibrated in dB to assist the setup of active loudspeaker systems or cut down unwanted noise from the input signal See page 13 2 Protect indicator This indicator illuminates if the amplifier tries to operate above its max
18. fiers we recommend racking is started from the bottom of the rack It is also recommended that rear supports are used for amplifiers mounted in the middle of the rack especially if used as part of a portable system 6 2 Cooling Your amplifier uses a forced air cooling system to maintain a low and even operating temperature All fan cooled Tannoy amplifiers have front to rear airflow There are several reasons for this one being that there is usually cooler air outside the rack than inside and therefore the amplifiers can run at higher continuous power levels without thermal problems Never try to reverse the airflow as the Intercooler needs a pressure chamber between the fans and heat sink and this only works in one direction of the airflow Should a heat sink get too hot its sensing circuit will mute the hot channel If the power supply overheats another sensing circuit will mute all output channels until it cools down to a safe operating temperature Make sure that there is an adequate air supply in front of the amplifier and that the rear of the amplifier has sufficient space to allow the exhaust to escape If the amplifier is rack mounted do not use covers or doors on the front or rear of the rack For installations with a central cooling system usually found in fixed installations with a dedicated rack room it may be necessary to calculate the maximum heat emission Refer to Power consumption on page 9 Tannoy Limited 8 T
19. ier is normally capable of producing far more power under these conditions than its normal undistorted rated output power The limiter works by monitoring the output and comparing the distortion produced between the input and output of the amplifier If the distortion exceeds 1 THD for any reason voltage or current clipping the limiter reduces the input signal proportionally Note that if the signal is distorted or clipped before it reaches the amplifier the clip limiter cannot detect it and will not be activated Under normal operation the clip limiting is inaudible The limiter can be turned On or Off by depressing or pressing the relevant clip limit switch Some manufacturers of loudspeaker controllers do not recommend the use of clip limiters in amplifiers as they tend to upset the tracking of the controller s limiters Apart from this one exception Tannoy recommend leaving the clip limiters switched on button depressed As a side effect once the amplifier comes out of a protect condition the output level has a slow rise time the effect is like turning the gain up slowly Tannoy Limited 13 TA 1400 User Manual 11 06 02 9 1 2 Thermal protection If the amplifier is driven very hard into a low impedance load the cooling fans will run at high speed If the causing conditions continue the Temperature indicator s will illuminate indicating that the amplifier is about to go into thermal shutdown After five seconds the amplifier w
20. ill go into thermal protection by muting the input signal After 15 20 seconds the amplifier will have cooled down enough for the amplifier to come out of shutdown and operate as normal If the load conditions remain unchanged the thermal protection will be reinitiated Thermal protection starts when the Intercooler heatsink reaches a temperature above 90 C 9 1 3 VHF protection If a signal above 12kHz is detected at the amplifier outputs for more than five seconds at full output power the VHF protection mutes the input signal This is indicated on the front panel 2 labeled Protect After five seconds the outputs will un mute and return to normal operation unless the output signal has remained unchanged in which case the VHF protection will re initiate 9 1 4 Short circuit protection All Tannoy amplifiers are completely short circuit protected The protection circuit permits very high peak currents but still holds the output devices within the safe operation area If a short circuit is maintained the channel affected will eventually go into thermal protect cycle until the short circuit has been removed 9 1 5 AC mains voltage protection If the AC mains voltage is over the allowed operational voltage the power supply will automatically shut down Once the mains voltage is above the minimum start voltage and below its maximum operating voltage the amplifier will restart 9 1 6 D C protection There are two types of DC protection
21. imum operating temperature 90 C The indicator first comes on as a warning to either turn down the input level or check the cooling arrangements Beyond the maximum temperature the amplifier will mute the input signal Once the cooling fans have brought the output heat sinks back to normal operating temperature the input signal is un muted This indicator also illuminates when signals above 12 kHz are continuously present at full power at the output terminals or if short circuit protection is activated If this occurs the input signal is muted and the process cycles until the VHF signal is no longer present or the short is removed See page 14 Tannoy Limited 4 TA 1400 User Manual 11 06 02 3 Clip limit indicator This indicator signals when the amplifier output is clipping or limiting It has two different indication states If the clip limiter is engaged it has a short time constant and it illuminates briefly See page 13 If the clip limiter is not engaged it has an increased time constant and it illuminates for a longer period 4 Signal present indicator Illuminates at 40dB below full output signal 5 On indicator The two bottom green ON LEDs indicate that the output circuits are receiving the correct rail voltage 6 Power switch Turns mains power on or off See page 9 and 12 7 Fan grill filters A grille with foam filters is located on the front panel to prevent dust from entering the amplifier The grille is
22. ing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as e Power supply cord or plug is damaged Liquid has been spilled into the unit An object has fallen into the unit The unit has been exposed to rain or moisture The unit does not operate normally e The unit was dropped or the enclosure is damaged 17 Do not remove top or bottom covers Removal of the cover will expose hazardous voltages There are no serviceable parts inside and removal may void the warranty 18 An experienced user shall always supervise this professional audio equipment especially if inexperienced adults or minors are using the equipment 3 5 User responsibility 3 5 1 Speaker damage Your amplifier is very powerful and can be potentially dangerous to both loudspeakers and humans alike Many loudspeakers can be easily damaged or destroyed by overpowering especially with the high power available from a bridged amplifier Always check the speaker s continuous and peak power capabilities Even if using the amplifier s front panel attenuator reduces the gain it is still possible to reach full output power if the input signal level is high enough 3 5 2 Speaker output hazard Power amplifiers are capable of producing hazardous output voltages To avoid electrical be shock do not touch any exposed speaker wiring while the amplifier is operating See page 6 about outputs for proper connection of speaker
23. ker coil gets warm Fault The amplifier goes into protection with power indicators off Check that the AC line voltage is within the amplifiers operating range 130 265V 230V 65 135V 115V Over voltage protection may have occurred If the amplifier is connected by Tannoy Limited 14 TA 1400 User Manual 11 06 02 mistake to a 3 phase supply an internal non resetable fuse or resistor may have blown Then return the amplifier to your supplier for service Fault The amplifier does not respond even after checking above items In the unlikely event of on a non user rectifiable fault return the amplifier to your supplier or an approved service centre Tannoy cannot be held responsible for damage or injury as a result of the top cover being removed 11 WARRANTY General This product is manufactured by Tannoy and is warranted to be free from defects in components and factory workmanship under normal use and service for a period of one 1 year from the date of original purchase During the warranty period Tannoy or its nominated agents will undertake to repair or at their option replace this product at no charge to its owner when failing to perform as specified provided the unit is returned undamaged and shipping pre paid to factory or authorised service facility This warranty shall be null and void if the product is subjected to Repair work or alteration by person other than those authorised by Tannoy or its agents Shi
24. nnecting any input or output or operating the switches on rear panel See pages 8 about installation e Make sure that the AC mains voltage is correct and the same as the one printed on the rear panel of the amplifier See pages 9 about operating voltage and power consumption e Make sure that the switches on the rear panel for operation modes gain switch and clip limiter switch are in the correct position See page 7 about operation modes and page 13 about clip limiters e tis always a good idea to turn down the gain controls during power up to prevent speaker damage in case a high signal is present at the input Tannoy Limited 12 TA 1400 User Manual 11 06 02 8 2 Powering up Soft start When you power up the amplifier it takes a couple of seconds to check its circuits This is known as the soft start or slow start sequence The fans then blow at high speed before going into idle and the two bottom green LED s illuminate to show the amplifier is operational 8 3 Input attenuators The two input level attenuators on the front panel adjust the signal level for their respective amplifier channel in all modes They are calibrated in dB to help setting up active loudspeaker systems or cutting down unwanted noise from the input signal In bridged mode both controls must be in the same position so that the speaker load will be shared equally between the channels 8 4 Indicators The yellow LEDs at the top indicat
25. pping accidents war civil insurrection misuse abuse operation with incorrect AC voltage operation with faulty associated equipment exposure to inclement weather conditions and normal wear and tear Units on which the serial number has been removed or defaced will not be eligible for warranty service Tannoy shall not be responsible for any incidental or consequential damages with respect to the products warranted Tannoy reserve the right to make changes or improvements in design or manufacturing without assuming any obligation to change or improve products previously manufactured This warranty is exclusive and no other warranty is expressed or implied This warranty does not affect your statutory rights International Please contact your supplier for this information as rights and disclaimers may vary from country to country Technical assistance and services International If your Tannoy product needs repair contact your Tannoy dealer or distributor or contact Tannoy Limited by fax or email to obtain the location of the nearest authorized service center Factory services In the event of your Tannoy product needing factory service you may contact Tannoy s service department for return instructions Please note for product return 1 Use the original packing 2 Include a copy of the sales receipt your name return address phone and fax number email address and description of the defect 3 Mark the Return Authoris
26. producing 700 watts per channel The 1 8 power per channel is accordingly 700 8 87 watts and total output 2 x 87 175 watts The power consumption according to the chart above is then 1200 watts The heat power produced is the difference between the power consumption and output power 1200 175 1025 watts per amplifier 7 CONNECTIONS 7 1 Input connections 7 1 1 Balanced inputs XLR Input connectors are active balanced and wired according to the IEC 268 that is pin 2 hot and wired in the following way PIN 1 GROUND SHIELD PIN 2 HOT PIN 3 COLD Gnd Figure 4 XLR input connector Figure 5 XLR balanced sli Tannoy Limited 10 TA 1400 User Manual 11 06 02 Within the Neutrik Combojack there is a 4 6 3mm phone jack which is wired in parallel with the XLR TIP HOT D RING COLD Ll SLEEVE SHIELD GROUND ii m Figure 6 14 TRS plug The input impedance is high enough 20 kohms balanced to allow daisy chaining or multiple parallel input connections e A The headroom of the input circuits is also high enough to accept the maximum output level from virtually any low level signal source Balanced signals are less sensitive to AC hum and radio interference The source impedance should be less than 1 kohms to avoid high frequency loss in long cables Bos oeoaenach ore Sr al To
27. s 3 5 3 Radio interference A sample of this product has been tested and complies with the limits for the European Electro Magnetic Compatibility EMC directive This equipment has also been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference from electrical equipment This product uses radio frequency energy and if not used or installed in accordance with these operating instructions may cause interference to other equipment such as radio receivers However there is no guarantee that interference will not occur in a particular installation Tannoy Limited 3 TA 1400 User Manual 11 06 02 If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Check if the affected unit complies with the EMC limits for immunity CE labelled If not address the problem with the manufacturer or supplier All electrical products sold in the EC must be approved for immunity against electromagnetic fields high voltage flash
28. st be used 6 6 Grounding There is no ground lift switch or terminal on this amplifier The signal ground is always floating via a resistor to chassis and the grounding system is automatic If a potential above 0 6V presents itself between signal ground and chassis ground a short circuit is introduced between the two thereby enabling electrical protection If a unit in the system is faulty its mains fuse will blow due to this automatic ground system If however you wish to tie the signal ground to chassis connect the XLR connector s shell lug to pin 1 In the interest of safety never disconnect the earth pin on the AC power cord For all units that are CE approved radio interference there is an AC mains filter This filter needs the chassis ground for reference otherwise a current loop is formed via the signal ground Use the balanced input to avoid hum and interference 6 7 Power consumption There are three ways to determine the power current consumption of the amplifier First the peak current draw at full output power Under this condition the power will blow the mains breaker within 30 second and the amplifier will operate for less than 2 minutes before thermally limiting During this time the temperature of the power supply will be stabilised at a temperature that will have no effect on the insulation rating of the AC line cord Second the maximum expected average current under worst case program material which is 1 3 of f
29. ull power according to the FTC standard At this level the music will be in the state of constant Tannoy Limited 9 TA 1400 User Manual 11 06 02 clip and is therefore the highest power level one can obtain without completely obliterating the program Last the normal operating power as defined by the safety standard IEC 65 ANSI UL 6500 and used by a majority of safety agencies The normal operating power is measured using pink noise with an average output power equal to 1 8 of full power The one eighth of the total power is as loud as you can play music while making some attempt to avoid obvious clipping It also corresponds to headroom of 9dB which is very low for normal audio program MAX OUTPUT POWER MAINS INPUT POWER Power 1 3 Power 1 8 Power Idle W note 1 note 2 TA 1400 8 ohms 2x 425 690 430 90 4 ohms 2x 700 1150 760 90 2 ohms 2x 1050 1925 1225 90 note 1 Average power with music as program source The amplifier driven to clip level note 2 Normal music power with 9dB headroom IEC standard power rating Table 1 6 7 1 Calculation The current draw can be calculated by dividing the mains input power by the mains voltage We recommend you to design the power distribution for at least the current at 1 8 power and 1 3 power for heavy duty demands like discos etc The heat power can be calculated as in the following example We consider headroom of at least 9dB and a 4 ohms load on an amplifier
Download Pdf Manuals
Related Search