TOA Electronics HS-1200BT User's Manual
Contents
1. Make sure that the volume control is set to minimum position before power is switched on Loud noise produced at high volume when power is switched on can impair hearing Do not operate the unit for an extended period of time with the sound distorting This is an indication of a malfunction which in turn can cause heat to generate and result in a fire 2 GENERAL DESCRIPTION TOA s HS 1200 series and HS 1500 series speakers are 2 way speaker systems made of resin and feature a large diameter woofer They can be installed in many different applications with combined use of the supplied handles and the optional mounting brackets 3 FEATURES Tweeter array realizes a 90 horizontal x 40 vertical directivity control at high frequencies Compact and lightweight with its high frequency tweeter array arranged in front of the low frequency woofer Built in overload protection circuitry for the tweeters Both permanent and temporary installations available Either vertical or horizontal speaker installation available for the permanent installation Easy to carry with a handy handle Both high and low impedance applications available by a rotary switch 4 DIMENSIONAL DIAGRAM Front Side Rear Screw terminal NEUTRIK NL4MP Speakon Rotary switch aaa 0000 Dimensions A B C Bottom HS 1200BT 1200WT 448 17 64 320 12. back and forth Align the datum line on the rubber foot with the positioning mark A on the speaker unit as shown at right Positioning mark Q 3 Rubber foot accessory Screw M6 x 30 accessory 8 5 Attaching a Handle Screw M6 x 30 The speaker system comes with a handy carrying handle accessory Attach the handle on the speaker s top surface Handle fitting bracket accessory Handle accessory 9 EQUALIZING BY THE DIGITAL SIGNAL PROCESSOR The speaker system is capable of providing high efficiency and wide range reproduction without using an equalizer however more clear and dynamic sound quality can be reproduced by using our digital signal processor and performing its settings as shown in the tables below For the HS 1200BT and HS 1200WT For the HS 1500BT and HS 1500WT Filter Frequency Hz Gain dB Q Filter Frequency Hz HPF 12 dB HPF 12 dB PEQ PEQ PEQ PEQ PEQ PEQ PEQ PEQ PEQ PEQ 10 SPECIFICATIONS HS 1200BT HS 1200WT HS 1500BT HS 1500WT Enclosure Sealed type Rated Power Continuous pink noise 100 W Continuous program 300 W Rated impedance 80 100 V line 170 Q 60 W 330 Q 30 W 670 Q 15 W 70 V line 83 Q 60 W 170 Q 30 W 330 Q 15 W 670 Q 7 5 W Sensitivity 97 dB 1 W 1m 98 dB 1 W 1m Frequency Response 70 to 20 000 Hz 60 to 20 000 Hz Crossover Frequency 3 kHz Directivity Angle Horizontal 90 Vertical 40 Spe
3. 2 6 361 14 21 HS 1500BT 1500WT 560 22 05 400 15 75 451 17 76 Unit mm inches 5 INPUT TERMINAL SECTION As the Speakon connector is internally connected in parallel to the screw terminal as shown below you can use either of the two The usable connector on the cable end that matches the NEUTRIK NLAMP Speakon is NEUTRIK NL4FX Speakon Input terminal connection diagram is as shown below Rear Input terminal connection diagram Dp o l Screw terminal p Speaker Speakon Se Screw terminal NEUTRIK NL4MP Speakon 6 IMPEDANCE CHANGE To change the impedance use a standard screwdriver to er rotate the rotary switch on the speaker s rear panel to select aS the desired input power This switch is factory preset to 670 Q Rotary switch Kroooooo eS Note When using a high impedance amplifier never select 8 Q SHE as this will damage the speaker and the amplifier LINE LINE Be sure to turn the rotary switch to 8 O when using a low 6709 15W 7 5W impedance amplifier 13309 30W 15w e 1709 GOW 30W D 839 60W OFF gt lt Rotary switch The figure represents factory preset position NE p 7 ABOUT THE INPUT OVERLOAD PROTECTION CIRCUIT The speaker system has a built in input overload protection circ
4. A ABO MIRE GA SEO EIE CES EAU Zu OA f OPERATING INSTRUCTIONS SPEAKER SYSTEMS HS 1200BT HS 1200WT HS 1500BT HS 1500WT Ne P TABLE OF CONTENTS 1 SAFETY PRECAUTIONS 2 8 INSTALLATION mn 5 2 GENERAL DESCRIPTION 3 9 EQUALIZING BY THE 3 FEATURES eet 3 DIGITAL SIGNAL PROCESSOR 7 4 DIMENSIONAL DIAGRAM janaan 3 10 SPECIFICATIONS 8 5 INPUT TERMINAL SECTION 4 ACCeSSOLGOS irren iiti iesnade 8 Optional products sseseseess 8 6 IMPEDANCE CHANGE 4 7 ABOUT THE INPUT OVERLOAD PROTECTION CIRCUIT 4 Thank you for purchasing TOA s Speaker System Please carefully follow the instructions in this manual to ensure long trouble free use of your equipment TOA Corporation 1 SAFETY PRECAUTIONS Before installation or use be sure to carefully read all the instructions in this section for correct and safe operation e Be sure to follow all the precautionary instructions in this section which contain important warnings and or cautions regarding safety After reading keep this manual handy for future reference Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which cou
5. HY 1200VB and HY 1200VW For the HS 1200 series speaker system HY 1500VB and HY 1500VW For the HS 1500 series speaker system They allow speaker s vertical angle to be adjusted Ceiling From 15 upward to 90 downward Wall From 15 upward to 60 downward Note They also permit speaker s horizontal angle to be adjusted in conjunction with the optional HY C0801 or HY C0801W Ceiling Mount Bracket or the HY W0801 or HY W0801W Wall Mount Bracket Ceiling installation Wall installation Mounting Bracket Mounting Bracket 8 1 2 HY 1200HB HY 1200HW HY 1500HB and HY 1500HW Mounting Brackets For horizontal speaker mounting These brackets are designed to mount HS series speakers to ceilings or walls horizontally HY 1200HB and HY 1200HW For the HS 1200 series speaker system HY 1500HB and HY 1500HW For the HS 1500 series speaker system They allow speaker s vertical angle to be adjusted Ceiling From 0 horizontal to 90 downward Wall From 15 upward to 60 downward Note They also permit speaker s horizontal angle to be adjusted in conjunction with the optional HY C0801 or HY C0801W Ceiling Mount Bracket or the HY W0801 or HY W0801W Wall Mount Bracket Ceiling installation Wall installation Mounting Bracket Mounting Bracket 8 1 3 HY C0801 and HY C0801W Ceiling Mount Brackets For ceiling installation horizontal angle adjustable Installing the HS series speaker to a ceiling in conjunction with th
6. aker Component Low frequency Low frequency 30 cm 12 cone type 38 cm 15 cone type High frequency High frequency Balanced dome tweeter x 6 balanced dome tweeter x 6 Input Terminal NEUTRIK NL4MP Speakon and M4 screw terminal Barrier spacing 9 mm Enclosure Polypropylene Polypropylene Polypropylene Polypropylene black white black white Punched net Surface treated Surface treated Surface treated Surface treated steel plate black steel plate white steel plate black steel plate white Operating Temperature 10 C to 50 C 14 F to 122 F Dimensions 361 w x 448 h x 320 d mm 451 w x 560 h x 400 d mm 14 21 x 17 64 x 12 6 17 76 x 22 05 x 15 75 Weight 10 kg 22 05 Ib 14 kg 30 86 Ib Finish Note The design and specifications are subject to change without notice for improvement Accessories Handle 5 2 2 ERES ee eed bei ee ee ees 1 Handle fitting bracket sss eme 2 RUDDENIOOL ee e E 2 Screw M6 x 30 Used for attaching a handle and rubber foot 4 Optional products Mounting bracket For vertical speaker mounting HY 1200VB HY 1200VW HY 1500VB HY 1500VW Mounting bracket For horizontal speaker mounting HY 1200HB HY 1200HW HY 1500HB HY 1500HW Ceiling mount bracket HY C0801 HY C0801W Wall mount bracket HY W0801 HY W0801W Speaker stand ST 33B Traceability Information for Europe EMC dire
7. ation position of an M8 bolt M8 Screw pitch 1 25 mm effective depth 24 mm Speaker s Note Unified inch screws cannot be used bottom surface Changing the orientation of the front panel logo Turn the logo mark while holding its edges to change its orientation 8 2 Mounting on the ST 33B Speaker Stand optional Note Refer to the instruction manual enclosed with the Speaker Speaker Stand for its mounting details Step 1 Fix the bracket supplied with the speaker stand Bracket to the speaker supplied with the Stand Step 2 Spread the tripod legs of the stand to their full extension 4 Note Bracket fixing screw Spread the tripod legs until the stays extend horizontally Plain washer for M8 supplied with the Stand Step 3 Mount the speaker with the bracket fixed onto the stand Speaker mounting screw M8 supplied with the Stand Step 4 Determine the speaker direction and tighten the bracket fixing screw Step 5 Adjust the stand height ST 83B Speaker Stand 8 3 Using as a Floor Monitor Notes When installing the speaker system on slippery floor put a non slip mat under the speaker Do not kick or stand on the speaker system as this will damage the speaker The figure shows the HS 1200 series 8 4 Attaching the Supplied Rubber Feet Attach the rubber feet in the case of speaker storage or on floor speaker installation Datum line Note The rubber foot has a direction
8. ctive 2004 108 EC Manufacturer Authorized representative TOA Corporation TOA Electronics Europe GmbH 7 2 1 Minatojima Nakamachi Chuo ku Kobe Hyogo Suederstrasse 282 20537 Hamburg Japan i Germany PA URL http www toa jp E TOA Corporation RR
9. e HY 1200 series or HY 1500 series Mounting Bracket permits the speaker s 7 horizontal angle to be adjusted Ceiling Moun Bracket The figure at right shows an example of vertical Mounting Bracket speaker installation 8 1 4 HY W0801 and HY W0801W Wall Mount Brackets For wall installation horizontal angl justabl For wall installation horizontal angle adjustable WEU Bra ke Installing the HS series speaker to a wall in conjunction with the HY 1200 series or HY 1500 series Mounting Bracket permits the speaker s horizontal angle to be adjusted Mounting Bracket The figure at right shows an example of vertical speaker installation 8 1 5 Safety wire installation For speaker fall prevention When mounting the speaker system to the ceiling or wall install a safety wire as needed AN WAR N l N When installing the safety wire be sure to follow the instructions below Failure to do so may cause the speaker to fall off resulting in personal injury Use a wire rope of 2 mm 0 08 or more in diameter The safety wire is not supplied e Tighten the safety wire to take up the slack Otherwise impact shock at speaker fall may cause the wire connected parts or wire itself to break Install the safety wire to a place that can structurally support the full weight of load Screw a speaker suspension bolt M8 into one of the screw holes on the speaker s bottom surface Then connect the safety wire to the bolt Install
10. e the unit to fall resulting in personal injury Ensure that all screws are securely tightened If they are not tightened or firmly secured after installation the unit could fall down possibly resulting in personal injury Use the specified mounting bracket in combination Doing otherwise may cause the unit or component to fall off resulting in personal injury Do not mount the unit in locations exposed to constant vibration The mounting bracket can be damaged by excessive vibration potentially causing the unit to fall which could result in personal injury CAUTIO N Indicates a potentially hazardous situation which if mishandled could result in moderate or minor personal injury and or property damage When Installing the Unit When unpacking or installing the unit be sure to handle it with two or more persons Falling or dropping the unit may cause personal injury Avoid touching the unit s sharp metal edge to prevent injury To avoid electric shocks be sure to switch off the amplifier s power when connecting speakers CAUTIO N Indicates a potentially hazardous situation which if mishandled could result in moderate or minor personal injury and or property damage When the Unit is in Use Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal injury and or property damage In addition the object itself may fall off and cause injury and or damage
11. ld result from mishandling Before operating your product read this manual first and understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards AN WAR N l NG Indicates a potentially hazardous situation which if mishandled could result in death or serious personal injury When Installing the Unit Avoid installing or mounting the unit in unstable locations such as on a rickety table or a slanted surface Doing so may result in the unit falling down and causing personal injury and or property damage Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket Doing otherwise may result in the unit falling down and causing personal injury and or property damage Since the unit is designed for in door use do not install it outdoors If installed outdoors the aging of parts causes the unit to fall off resulting in personal injury Also when it gets wet with rain there is a danger of electric shock Owing to the unit s size and weight be sure that at least two persons are available to install the unit Failure to do so could result in personal injury Do not use other methods than specified to mount the bracket Extreme force is applied to the unit and the unit could fall off possibly resulting in personal injuries Use screws that are appropriate for the ceiling s or wall s structure and composition Failure to do so may caus
12. uitry If an excessive input signal is applied to the speaker the protection circuitry is activated and cuts off the signal input to the tweeters A sudden drop of the sound volume level during speaker operation indicates that the protection circuitry has been activated In Such a case reduce the amplifier volume and wait The protection circuitry is automatically reset after approximately 10 seconds After the circuitry is reset set the volume at a lower level than before Note This input overload protection circuitry does not completely protect the speaker component Depending on the nature of the excessive input signal applied to the speaker there may be damage to the speaker components before protection circuitry can operate Also if the excessive input signal is applied to the speaker for extended periods of time the protection circuitry may be damaged and will not recover Take special care that the excessive input signal is not applied to the speaker during use 8 INSTALLATION 8 1 Installing to a Ceiling or Wall Install the speaker system to a ceiling or wall using the optional mounting brackets shown below Note Refer to the instruction manual enclosed with the HY 1200 series or HY 1500 series Mounting Bracket for its mounting details 8 1 1 HY 1200VB HY 1200VW HY 1500VB and HY 1500VW Mounting Brackets For vertical speaker mounting These brackets are designed to mount HS series speakers to ceilings or walls vertically
Download Pdf Manuals
Related Search