Home

Texas Instruments TMS320TCI6486 User's Manual

1. Table 51 Figure 57 Receive Interrupt Mask Set Register RXINTMASKSET 31 24 Reserved R 0 23 22 21 20 19 18 17 16 RX7PULSE RX6PULSE RX5PULSE RX4PULSE RX3PULSE RX2PULSE RX1PULSE RXOPULSE MASK MASK MASK MASK MASK MASK MASK MASK 15 Reserved R 0 7 6 5 4 3 2 1 0 RX7PEND RX6PEND RX5PEND RX4PEND RX3PEND RX2PEND RX1PEND RXOPEND MASK MASK MASK MASK MASK MASK MASK MASK LEGEND R W Read Write R Read only n value after reset Table 51 Receive Interrupt Mask Set Register RXINTMASKSET Field Descriptions Bit Field Value Description 31 24 Reserved 0 Reserved read as 0 23 RX7PULSEMASK 0 Receive channel 7 pulse interrupt mask Write 1 to enable interrupt 22 RX6PULSEMASK 0 Receive channel 6 pulse interrupt mask Write 1 to enable interrupt 21 RX5PULSEMASK 0 Receive channel 5 pulse interrupt mask Write 1 to enable interrupt 20 RX4PULSEMASK 0 Receive channel 4 pulse interrupt mask Write 1 to enable interrupt 19 RX3PULSEMASK 0 Receive channel 3 pulse interrupt mask Write 1 to enable interrupt 18 RX2PULSEMASK 0 Receive channel 2 pulse interrupt mask Write 1 to enable interrupt 17 RX1PULSEMASK 0 Receive channel 1 pulse interrupt mask Write 1 to enable interrupt 16 RXOPULSEMASK 0 Receive channel 0 pulse interrupt mask Write 1 to enable interrupt 15 8 Reserved 0 Reserved read as 0 7 RX7PENDMASK 0 Receive channel
2. 74 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMIC Module Registers 3 3 2 TPSTAT Registers There are eight TPSTAT registers TPSTATO through TPSTAT7 one per transmit event This register configuration is common to all C64x mega modules The TPSTAT register details are shown in Figure 27 and described in Table 20 Figure 27 TPSTAT Register 31 28 27 16 Reserved TIME 0000 R 0000 0000 15 8 7 4 3 2 1 0 CNT Reserved TIM_SM DIV_SM R 0000 0000 0000 R 00 R 00 LEGEND R W Read Write R Read only n value after reset Table 20 TPSTAT Register Field Descriptions Bit Field Value Description 31 28 Reserved Reserved 27 16 TIME Current time delay value 15 8 CNT Current divide by N value 7 4 Reserved Reserved 3 2 TIM_SM Time delay SM 00 Time delay SM in WAITING state 01 Time delay SM in DELAY state 10 Time delay SM in OUTPUT state 11 Reserved 1 0 DIV_SM Divide by N SM 00 Divide by N SM in WAITING state 01 Divide by N SM in DELAY state 10 Divide by N SM in OUTPUT state 11 Reserved 3 4 Prescalar Configuration Register PSCFG There is a single PSCFG register for the wrapper It contains the reload value for the prescalar configuration value The PSCFG register is shown in Figure 28
3. 31 16 Reserved HO 15 1 0 Reserved RXEN R 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 41 Receive Control Register RXCONTROL Field Descriptions Bit Field Value Description 31 1 Reserved 0 Reserved 0 RXEN Receive DMA enable 0 Receive is disabled Receive is enabled SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 99 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 6 Receive Teardown Register RXTEARDOWN The receive teardown register RXTEARDOWN is shown in Figure 48 and described in Table 42 Figure 48 Receive Teardown Register RXTEARDOWN 31 16 RXTD NRDY Reserved HO 15 3 2 0 Reserved RXTDNCH HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 42 Receive Teardown Register RXTEARDOWN Field Descriptions Bit Field Value Description 31 RXTDNRDY 0 Receive teardown ready Read as zero but is always assumed to be one unused 30 3 Reserved 0 Reserved 2 0 RXTDNCH Receive teardown channel Receive channel teardown is commanded by writing the encoded value of the receive channel to be torn down The teardown register is read as zero 0 Teardown receive channel 0 th Teardown receive channel 1 2h Teardown receive channel 2 3h Teardown receive channel 3 4h Teardown receive channel 4 5h Teardown rec
4. Bit Field Value Description 31 23 Reserved 0 Reserved 22 16 RXFIFOFLOWTHRESH Receive FIFO flow control threshold Occupancy of the receive FIFO when Receive FIFO flow control is triggered if enabled The default value is 0x2 which means that receive FIFO flow control is triggered when the occupancy of the FIFO reaches two cells 15 5 Reserved 0 Reserved 4 0 TXCELLTHRESH Transmit FIFO cell threshold Indicates the number of 64 byte packet cells required to be in the transmit FIFO before the packet transfer is initiated Packets with fewer cells are initiated when the complete packet is contained in the FIFO This value must be greater then or equal to 2 and less than or equal to 24 130 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 33 MAC Configuration Register MACCONFIG The MAC configuration register MACCONFIG is shown in Figure 75 and described in Table 69 Figure 75 MAC Configuration Register MACCONFIG 31 24 23 16 TXCELLDEPTH RXCELLDEPTH R 24 R 68 15 8 7 0 ADDRESSTYPE MACCFIG R 2 R 3 LEGEND R W Read Write R Read only n value after reset Table 69 MAC Configuration Register MACCONFIG Field Descriptions Bit Field Value Description 31 24 TXCELLDEPTH
5. INSTRUMENTS www ti com EMAC Functional Architecture 2 5 5 Receive Buffer Descriptor Format A receive RX buffer descriptor Figure 13 is a contiguous block of four 32 bit data words aligned on a 32 bit boundary that describes a packet or a packet fragment Example 2 shows the receive descriptor described by a C structure Figure 13 Receive Descriptor Format a Word 0 31 0 Next Descriptor Pointer b Word 1 31 0 Buffer Pointer c Word 2 31 16 15 H Buffer Offset Buffer Length d Word 3 31 30 29 28 27 26 25 24 SOP EOP OWNER EOQ TDOWNCMPLT PASSCRC JABBER OVERSIZE 23 22 21 20 19 18 17 16 FRAGMENT UNDERSIZED CONTROL OVERRUN CODEERROR ALIGNERROR CRCERROR NOMATCH 15 0 Packet Length Example 2 Receive Descriptor in C Structure Format EMAC Descriptor The following is the format of a single buffer descriptor on the EMAC typedef struct _EMAC_Desc struct _EMAC_ Desc pNext Pointer to next descriptor in chain Uint8 pBuffer Pointer to data buffer Uint32 BufOfflLen Buffer Offset MSW and Length LSW Uint32 PktFlgLen Packet Flags MSW and Length LSW EMAC_Desc Packet Flags define EMAC_DSC_FLAG_SOP 0x80000000u define EMAC_DSC_FLAG_ EOP 0x40000000u define EMAC_DSC_FLAG_ OWNER 0x20000000u define EMAC_DSC_FLAG_EOQ 0x10000000u define EMAC_DSC_FLAG_TDOWNCMPLT 0x08000000u define EMAC_DSC_FLAG_PASSCRC 0x04000000u define EMAC_DSC_FLAG_ JABBER 0x02000000u define EMAC_DSC_FLAG OVERSIZ
6. 18 FAULTENB Fault detect enable This bit has to be set to 1 to enable the physical layer fault detection 0 Disables the physical layer fault detection Enables the physical layer fault detection 17 16 Reserved 0 Reserved 15 0 CLKDIV Clock Divider bits This field specifies the division ratio between peripheral bus set to 0 MDCLK frequency peripheral clock frequency CLKDIV 1 peripheral clock and the frequency of MDCLK MDCLK is disabled when CLKDIV is 78 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 4 PHY Acknowledge Status Register ALIVE The PHY acknowledge status register ALIVE is shown in Figure 31 and described in Table 24 Figure 31 PHY Acknowledge Status Register ALIVE 31 16 ALIVE R WC 0 15 0 ALIVE R WC 0 LEGEND R W Read Write R WC Read Write 1 to clear n value after reset Table 24 PHY Acknowledge Status Register ALIVE Field Descriptions Bit Field Value Description 31 0 ALIVE MDIO Alive bits Each of the 32 bits of this register is set if the most recent access to the PHY with address corresponding to the register bit number was acknowledged by the PHY the bit is reset if the PHY fails to acknowledge the access Both the user and polling accesses to a PHY will cause t
7. External logic element Low skew buffer Zero delay clock buffer SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture S3MII multi PHY TX_CLK TX_SYNC P TD PO_RXD RX_SYNC RX_CLK C6472 TCI6486 EMAC MDIO 27 I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com In the case of the S3MIl switch where the switch has only one TX_SYNC for all ports external logic is needed to synchronize the TX_SYNC signals from multiple ports or TC16486 C6472 devices The TXD signal from the multiple ports should also be synchronized using external logic since the clock phase relation of different TC16486 C6472 devices can be different Figure 8 demonstrates the example mutli PHY configuration for S3MII Figure 8 S3MII Switch Configuration S3MIl switch TX_CLK TX_SYNC Device 1 TXD TX_SYNC TX_CLK RXD RX_SYNC RX_CLK MHZ_125_CLK PO_TXD PO_RXD Device 2 TXD TX_SYNC TX_CLK RXD RX_SYNC External logic element RX_CLK MHZ_125_CLK Device n TXD TX_SYNC TX_CLK RXD RX_SYNC RX_CLK MHZ_125_CLK Low skew buffer RX_SYNC 125 MHz zero delay clock buffer 125 MHz XO Zero delay
8. Figure 10 Basic Descriptor Format Word Offset Bit Fields 31 16 15 0 Next Descriptor Pointer Buffer Pointer Buffer Offset Buffer Length G IMlsa hlO Flags Packet Length Table 13 Basic Descriptors Word Offset Field Field Description 0 Next Descriptor Pointer Buffer Pointer Buffer Offset Buffer Length Flags Packet Length The next descriptor pointer creates a single linked list of descriptors Each descriptor describes a packet or a packet fragment When a descriptor points to a single buffer packet or the first fragment of a packet the start of packet SOP flag is set in the flags field When a descriptor points to a single buffer packet or the last fragment of a packet the end of packet EOP flag is set When a packet is fragmented each fragment must have its own descriptor and appear sequentially in the descriptor linked list The buffer pointer refers to the memory buffer that either contains packet data during transmit operations or is an empty buffer ready to receive packet data during receive operations The buffer offset is the offset from the start of the packet buffer to the first byte of valid data This field only has meaning when the buffer descriptor points to a buffer that contains data The buffer length is the number of valid packet data bytes stored in the buffer If the buffer is empty and waiting to receive data this field repres
9. 0 and EMAC1_EN Decoding MACSEL02 MACSEL01 MACSELO0 MACSEL11 MACSEL10 EMAC_EN EMACO EMAC1 0 0 0 X X 0 MII None 0 0 0 0 X 1 MII None 0 0 0 1 0 1 MII RGMII 0 1 0 X X 0 GMIl None 0 1 0 0 X 1 GMII None 0 1 0 1 0 1 GMIl RGMII 0 0 1 X X 0 RMII None 0 1 1 X xX 0 RGMII None 1 0 0 X X 0 None None 1 0 1 xX X 0 S3MIl None 0 0 1 0 0 1 RMII None 0 0 1 0 1 1 RMII S3MIl 0 0 1 1 0 1 RMII RGMII 0 0 1 1 1 1 RMII RMII 0 1 1 0 0 1 RGMII None 0 1 1 0 1 1 RGMII S3MIl 0 1 1 1 0 1 RGMII RGMII 0 1 1 1 1 1 RGMII RMII 1 0 0 0 0 1 None None 1 0 0 0 1 1 None S3MIl 1 0 0 1 0 1 None RGMII SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated C6472 TCI6486 EMAC MDIO 17 EMAC Functional Architecture A TEXAS INSTRUMENTS www ti com Table 6 MACSELO 2 0 MACSEL1 1 0 and EMAC1_EN Decoding continued MACSEL02 MACSEL01 MACSELO0 MACSEL11 MACSEL10 EMAC_EN EMACO EMAC1 1 0 0 1 1 1 None RMII 1 0 1 0 0 1 S3MIl None 1 0 1 0 1 1 S3MIl S3MIl 1 0 1 1 0 1 S3MIl RGMII 1 0 1 1 1 1 S3MIl RMII 1 1 1 X X 0 None None 1 1 1 0 0 1 None None 1 1 1 0 1 1 None S3MIl 1 1 1 1 0 1 None RGMII 1 1 1 1 1 1 None RMII 2 3 1 Media Independent Interface MII Connections Figure 2 shows a TCI6486 C6472 device with integrated EMAC and MDIO interfaced to the PHY via an MII connection This interface is only available in 10 Mbps and 100 Mbps modes Figure
10. 138 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 41 Receive Pause Timer Register RXPAUSE The receive pause timer register RXPAUSE is shown in Figure 83 and described in Table 77 Figure 83 Receive Pause Timer Register RXPAUSE 31 16 Reserved HO 15 PAUSETIMER HO LEGEND R Read only n value after reset Table 77 Receive Pause Timer Register RXPAUSE Field Descriptions Bit Field Value Description 31 16 Reserved 0 Reserved 15 0 PAUSETIMER Receive pause timer value These bits allow the contents of the receive pause timer to be observed The receive pause timer is loaded with FFOOh when the EMAC sends an outgoing pause frame with pause time of FFFFh The receive pause timer is decremented at slot time intervals If the receive pause timer decrements to 0 then another outgoing pause frame is sent and the load decrement process is repeated SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 139 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 42 Transmit Pause Timer Register TXPAUSE The transmit pause timer register TXPAUSE is shown in Figure 84 and described in Table 78
11. All the interrupts signaled from the EMAC and MDIO modules are level driven If they remain active their level remains constant However the CPU core requires edge triggered interrupts To properly convert the level driven interrupt signal to an edge triggered signal the application software must use the interrupt control logic of the EMIC module For safe interrupt processing the software application should disable interrupts using the EMIC module interrupt control register EW_INTCTL upon entry to the ISR and re enable them upon leaving the ISR 2 17 4 Interrupt Multiplexing The EMIC module combines different interrupt signals from both the EMAC and MDIO modules and generates a single interrupt signal that is wired to the CPU interrupt controller Once this interrupt is generated the reason for the interrupt can be read from the MACINVECTOR register located in the EMAC memory map MACINVECTOR combines the status of the following 20 interrupt signals TXPENDn RXPENDn STATPEND HOSTPEND LINKINT and USERINT The EMAC and MDIO interrupts are combined within the EMIC module and mapped to system events 70 and 71 through the use of the enhanced interrupt selector within the C64x core For more details see the Interrupt Controller chapter in the TMS320C64x Megamodule Peripherals Reference Guide SPRU871 and the TMS320TCI6486 Communications Infrastructure Digital Signal Processor data manual SPRS300 or the TMS320C6472 Fixed Point Digital
12. C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated TEXAS INSTRUMENTS www ti com EMAC Functional Architecture Receive buffer flow control is triggered when the number of free buffers in any enabled receive channel RXnFREEBUFFER is less than or equal to the channel flow control threshold register RXNFLOWTHRESH value Receive flow control is independent of receive QOS except that both use the free buffer values When enabled and triggered receive FIFO flow control prevents further frame reception based on the number of cells currently in the receive FIFO Receive FIFO flow control may be enabled only in full duplex mode FULLDUPLEX bit is set in the MACCONTROL register Receive flow control prevents reception of frames on the port until all of the triggering conditions clear at which time frames may again be received by the port Receive FIFO flow control is triggered when the occupancy of the FIFO is greater than or equal to the RXFIFOFLOWTHRESH value in the FIFOCONTROL register The RXFIFOFLOWTHRESH value must be greater than or equal to 1h and less than or equal to 42h decimal 66 The RXFIFOFLOWTHRESH reset value is 2h Receive flow control is enabled by the RXBUFFERFLOWEN bit and the RXFIFOFLOWEN bit in the MACCONTROL register The FULLDUPLEX bit in the MACCONTROL register configures the EMAC for collision or IEEE 802 3X flow c
13. Copyright 2006 2010 Texas Instruments Incorporated EMAC Port Registers A TEXAS INSTRUMENTS www ti com Table 57 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE Field Descriptions continued Bit Field Value Description 22 RXCEFEN Receive copy error frames enable bit Enables frames containing errors to be transferred to memory The appropriate error bit will be set in the frame EOP buffer descriptor 0 Frames containing errors are filtered 1 Frames containing errors are transferred to memory 21 RXCAFEN Receive copy all frames enable bit Enables frames that do not address match includes multicast frames that do not hash match to be transferred to the promiscuous channel selected by RXPROMCH bits Such frames will be marked with the NOMATCH bit in their EOP buffer descriptor 0 Frames that do not address match are filtered 1 Frames that do not address match are transferred to the promiscuous channel selected by RXPROMCH bits 20 19 Reserved 0 Reserved 18 16 RXPROMCH 0 3h Receive promiscuous channel select 0 Select channel 0 to receive promiscuous frames th Select channel 1 to receive promiscuous frames 2h Select channel 2 to receive promiscuous frames 3h Select channel 3 to receive promiscuous frames 4h Select channel 4 to receive promiscuous frames 5h Select channel 5 to receive promiscuous frames 6h Select channel 6 to receive promiscuous fra
14. Figure 28 Prescalar Configuration Register PSCFG 31 16 Reserved 0000 0000 15 0 PRESCALE_CFG R W 0000 0000 LEGEND R W Read Write R Read only n value after reset SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 75 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated IA TEXAS INSTRUMENTS MDIO Registers www ti com 4 MDIO Registers 4 1 Introduction Table 21 lists the memory mapped registers for the Management Data Input Output MDIO For the memory address of these registers see the TMS320TCI6486 Communications Infrastructure Digital Signal Processor data manual SPRS300 or the 7MS320C6472 Fixed Point Digital Signal Processor data manual SPRS612 Table 21 Management Data Input Output MDIO Registers Offset Acronym Register Description See Oh VERSION MDIO Version Register Section 4 2 4h CONTROL MDIO Control Register Section 4 3 8h ALIVE PHY Alive Status register Section 4 4 Ch LINK PHY Link Status Register Section 4 5 10h LINKINTRAW MDIO Link Status Change Interrupt Unmasked Register Section 4 6 14h LINKINTMASKED MDIO Link Status Change Interrupt Masked Register Section 4 7 20h USERINTRAW MDIO User Command Complete Interrupt Unmasked Section 4 8 Register 24h USERINTMASKED MDIO User Command Complete Interrupt Masked Register Section 4 9 28h USERINTMASKSET MDIO User Command Complete Interrupt Mask Set Register Section 4 10 2Ch USERINTMASKCLEA
15. Figure 84 Transmit Pause Timer Register TXPAUSE 31 16 Reserved HO 15 0 PAUSETIMER HO LEGEND R Read only n value after reset Table 78 Transmit Pause Timer Register TXPAUSE Field Descriptions Bit Field Value Description 31 16 Reserved 0 Reserved 15 0 PAUSETIMER Transmit pause timer value These bits allow the contents of the transmit pause timer to be observed The transmit pause timer is loaded by a received incoming pause frame and then decremented at slot time intervals down to 0 at which time EMAC transmit frames are again enabled SPRUEF8F March 2006 Revised November 2010 140 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 43 MAC Address Low Bytes Register MACADDRLO The MAC address low bytes register MACADDRLO is shown in Figure 85 and described in Table 79 Figure 85 MAC Address Low Bytes Register MACADDRLO 31 21 20 19 18 16 Reserved vaLip MATCH CHANNEL FILT R 0 RIW x RWx R W x 15 8 7 0 MACADDRO MACADDR1 R W 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 79 MAC Address Low Bytes Register MACADDRLO Field Descriptions Bit Field Value Description 31 21 Reserved 0 Reserved 20 VALID Address valid bit Th
16. MDIO_REGS gt CONTROL CSL_FMKT MDIO_CONTROL_ENABLE YES CSL_FMK MDIO_CONTROL_CLKDIV PCLK SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 65 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 16 4 66 If the MDIO module must operate on an interrupt basis the interrupts can be enabled at this time using the USERINTMASKSET register for register access and the USERPHYSELn register if a target PHY is already known Once the MDIO state machine has been initialized and enabled it starts polling all 32 PHY addresses on the MDIO bus looking for active PHYs Since it can take up to 50 us to read one register the MDIO module provides an accurate representation of all the PHYs available after a reasonable interval Also a PHY can take up to 3 seconds to negotiate a link Thus it is advisable to run the MDIO software off a time based event rather than polling For more information on PHY control registers see the PHY device documentation EMAC Module Initialization The EMAC module sends and receives data packets over the network by maintaining up to 8 transmit and receive descriptor queues The EMAC module configuration must also be kept current based on the PHY negotiation results returned from the MDIO module Programming this module is the most time consuming aspect of developing an application or de
17. RMTXEN The transmit enable signal indicates that the RMTXD pins are generating nibble data for use by the PHY It is driven synchronously to the RMII reference clock RMCRSDV l Carrier sense receive data valid RMCRSDV The RMCRSDV pin is asserted by the PHY when the network is not idle in either transmit or receive The data on RMRXD is considered valid once the RMCRSDV signal is asserted The pin is de asserted when both transmit and receive are idle The assertion of this signal is asynchronous to the RMII reference clock RMREFCLK l Reference clock RMREFCLKk A 50 MHz clock must be provided through this pin for RMII operation RMRXDf 1 0 l Receive data RMRXD The receive data pins are a collection of 2 data signals comprising 2 bits of data RMRDXO is the least significant bit LSB The signals are synchronized to the RMII reference clock and valid only when RMCRSDV is asserted In 10 Mbps operation RMRXD is sampled every tenth cycle of the RMII reference clock 20 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS www ti com EMAC Functional Architecture Table 8 EMAC and MDIO Signals for RMII Interface continued Signal Name UO Description RMRXER l Receive error RMRXER The receive error signal is asserted for one or more reference clock periods to indicate that an error was detected in the
18. See Section 2 5 5 for alignment code CRC error definitions Overruns have no effect on this statistic 5 50 4 Pause Receive Frames Register RXPAUSEFRAMES The total number of IEEE 802 3X pause frames received by the EMAC whether acted upon or not A pause frame is defined as having all of the following e Contained any unicast broadcast or multicast address e Contained the length type field value 88 08h and the opcode 0001h e Was of length 64 to RXMAXLEN bytes inclusive e Had no CRC error alignment error or code error e Pause frames had been enabled on the EMAC TXFLOWEN bit is set in MACCONTROL The EMAC could have been in either half duplex or full duplex mode See Section 2 5 5 for alignment code CRC error definitions Overruns have no effect on this statistic 5 50 5 Receive CRC Errors Register RXCRCERRORS The total number of frames received on the EMAC that experienced a CRC error A frame with CRC errors is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of length 64 to RXMAXLEN bytes inclusive e Had no alignment or code error e Had a CRC error A CRC error is defined as having all of the following A frame containing an even number of nibbles Fails the frame check sequence test See Section 2 5 5 for definitions of alignment and code errors Overruns have no effect on this statistic 5 50
19. TIME_CFG Time delay configuration value 15 8 CNT_CFG Divide by N configuration value 7 4 Reserved Reserved 3 TU Write only bit reads return 0 0 N A 1 Enables writes to TIME_CFG 2 CU Write only bit reads return 0 0 N A 1 Enables writes to CNT_CFG 1 TR Write only bit reads return 0 0 N A 1 Resets the timer counter 0 CR Write only bit reads return 0 0 N A 1 Resets the divide by N count 72 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMIC Module Registers 3 2 2 RPSTAT Registers There are eight RPSTAT registers RPSTATO thru RPSTAT7 one per receive event This register configuration is common to all C64x megamodules The RPSTAT register details are shown in Figure 25 and described in Table 18 Figure 25 RPSTAT Register 31 28 27 16 Reserved TIME 0000 R 0000 0000 15 8 7 4 3 2 1 0 CNT Reserved TIM_SM DIV_SM R 0000 0000 0000 R 00 R 00 LEGEND R W Read Write R Read only n value after reset Table 18 RPSTAT Register Field Descriptions Bit Field Value Description 31 28 Reserved Reserved 27 16 TIME Current time delay value 15 8 CNT Current divide by N value 7 4 Reserved Reserved 3 2 TIM_SM Time delay SM 00 Time delay SM in WAITING state 01 Time delay SM in DELAY state 10 Time delay SM in OUTPUT state 11 Res
20. however its value is reserved for broadcast It is classified separately by the EMAC Descriptor Packet Buffer Descriptor A small memory structure that describes a larger block of memory in terms of size location and state Descriptors are used by the EMAC and application to describe the memory buffers that hold Ethernet data Device In this document device refers to the TMS320TCI6486 TMS320C6472 digital signal processor Ethernet MAC Address MAC Address A unique 6 byte address that identifies an Ethernet device on the network In an Ethernet packet a MAC address is used twice first to identify the packet s destination and second to identify the packet s sender or source An Ethernet MAC address is normally specified in hexadecimal using dashes to separate bytes For example 08h 00h 28h 32h 17h 42h The first three bytes normally designate the manufacturer of the device However when the first byte of the address is odd LSB is 1 the address is a group address broadcast or multicast The second bit specifies whether the address is globally or locally administrated not considered in this document Ethernet Packet Packet An Ethernet packet is the collection of bytes that represents the data portion of a single Ethernet frame on the wire Full Duplex Full duplex operation allows simultaneous communication between a pair of stations using point to point media dedicated channel Full duplex operation does not
21. or matched due to promiscuous mode e Was greater than RXMAXLEN in bytes e Had no CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code CRC errors Overruns have no effect on this statistic 5 50 8 Receive Jabber Frames Register RXJABBER The total number of jabber frames received on the EMAC A jabber frame is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was greater than RXMAXLEN bytes long e Hada CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic 5 50 9 Receive Undersized Frames Register RXUNDERSIZED The total number of undersized frames received on the EMAC An undersized frame is defined as having all of the following e Was any data frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was less than 64 bytes long e Had no CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic 5 50 10 Receive Frame Fragments Register RXFRAGMENTS The total number of frame fragments received on the EMAC A frame fragment is defined as having all of the following e Any data frame address matching does not matter e Was less t
22. this enables the PHY to generate the receive clock that is sent to EMAC The RGMII protocol takes a GMII data stream and turns it into an interface with half of the data bus width and sends the same amount of data with a reduced pinout The RGMII protocol also allows for dynamic switching of the mode between 10 100 1000 Mbps modes This negotiation data is embedded in the incoming data stream from the external PHY For timing purposes data is transmitted and received with respect to MTCLK and MRCLK respectively The RGMII interface has separate I O pins from the other EMAC pins because the interface voltage is different from the other interfaces S3MII Clocking S3MIl mode is selected by programming MACSELO to 5 101b and MACSEL1 to 1 01b The S3MII gasket needs a 125 MHz continuous clock 125 CLK supplied by an external source It also needs a peripheral bus clock as input MTCLK and MRCLK are fixed at 125 MHz Memory Map The EMAC includes an internal memory that holds information about the Ethernet packets that are received or transmitted This internal RAM is 2K x 32 bits in size The data can be written to and read from the EMAC internal memory via either the EMAC or the CPU It stores buffer descriptors that are 4 words 16 bytes deep This 8K local memory holds enough information to transfer up to 512 Ethernet packets without CPU intervention The packet buffer descriptors can be put in internal processor memory L2 on the TCl64
23. 2 Ethernet Configuration with MIl Interface MTCLK MTXD 3 0 MTXEN MCOL MCRS Physical MRCLK layer Transformer device MRXD 3 0 PHY Table 7 summarizes the individual EMAC and MDIO signals for the MII interface For more information refer to either the IEEE 802 3 standard or ISO IEC 8802 3 2000 E The EMAC module does not include a transmit error MTXER pin If a transmit error occurs CRC inversion is used to negate the validity of the transmitted frame 18 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated TEXAS INSTRUMENTS www ti com EMAC Functional Architecture Table 7 EMAC and MDIO Signals for MIl Interface Signal Name HO Description MTCLK l Transmit clock MTCLK The transmit clock is a continuous clock that provides the timing reference for transmit operations The MTXD and MTXEN signals are tied to this clock The clock is generated by the PHY and is 2 5 MHz at 10 Mbps operation and 25 MHz at 100 Mbps operation MTXD 3 0 O Transmit data MTXD The transmit data pins are a collection of 4 data signals comprising 4 bits of data MTDXO is the least significant bit LSB The signals are synchronized by MTCLK and valid only when MTXEN is asserted MTXEN O Transmit enable MTXEN The transmit enable signal indicates that the MTXD pins are generating nibble d
24. 2 Receive Packet Completion Interrupts The receive DMA engine has eight channels and each channel has a corresponding interrupt RXPENDn The receive interrupts are level interrupts that remain asserted until cleared by the CPU Each of the eight receive channel interrupts may be individually enabled by setting the appropriate bit in the RXINTMASKSET register Each of the eight receive channel interrupts may be individually disabled by clearing the appropriate bit in the RXINTMASKCLEAR register The raw and masked receive interrupt status may be read by reading the RXINTSTATRAW and RXINTSTATMASKED registers respectively When the EMAC completes a packet reception the EMAC issues an interrupt to the CPU by writing the packet s last buffer descriptor address to the appropriate channel queue s RX completion pointer located in the state RAM block The write generates the interrupt when enabled by the interrupt mask regardless of the value written SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 67 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com Upon interrupt reception the CPU processes one or more packets from the buffer chain and then acknowledges one or more interrupt s by writing the address of the last buffer descriptor processed to the queue s associated RX completion pointer in the receive DMA state RAM The dat
25. 2010 C6472 TCI6486 EMAC MDIO 57 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC A TEXAS INSTRUMENTS Functional Architecture www ti com 2 10 2 7 Speed Duplex and Pause Frame Support 2 11 2 11 1 2 11 2 2 11 3 58 The MAC can operate in half duplex or full duplex mode at 10 Mbps or 100 Mbps and can operate in full duplex only in 1000 Mbps Pause frame support is included in 10 100 1000 Mbps modes as configured by the host Packet Receive Operation Receive DMA Host Configuration To configure the receive DMA for operation the host must perform the following actions e Initialize the receive addresses e Initialize the RXnNHDP registers to zero e Write the MACHASH1 and MACHASH2 registers if hash matching multicast addressing is desired e Initialize the RXnFREEBUFFER RXnFLOWTHRESH and RXFILTERLOWTHRESH registers if flow control is to be enabled e Enable the desired receive interrupts using the RXINTMASKSET and RXINTMASKCLEAR registers e Set the appropriate configuration bits in the MACCONTROL register e Write the RXKBUFFEROFFSET register value typically zero e Set up the receive channel s buffer descriptors and initialize the RXnHDP registers e Enable the receive DMA controller by setting the RXEN bit in the RXCONTROL register e Configure and enable the receive operation as desired in the RXMBPENABLE register and by using the RXUNICASTSET and RXUNICASTCLEAR regist
26. 49 Receive Interrupt Status Unmasked Register RXINTSTATRAW Field Descriptions eceeeeeeeeee 107 50 Receive Interrupt Status Masked Register RXINTSTATMASKED Field Descriptions 0 seeeeeeeee 108 51 Receive Interrupt Mask Set Register RXINTMASKSET Field Description 109 52 Receive Interrupt Mask Clear Register RXINTMASKCLEAR Field Descriptions 0cseeeeeeeeeeeeeeee 110 53 MAC Interrupt Status Unmasked Register MACINTSTATRAW Field Descriptions s2eeseeees 111 54 MAC Interrupt Status Masked Register MACINTSTATMASKED Field Descriptons 112 55 MAC Interrupt Mask Set Register MACINTMASKSET Field Descriptions 0 seeeeeeeeeeeeeeeeeeeeeeees 113 56 MAC Interrupt Mask Clear Register MACINTMASKCLEAR Field Descriptions 2 seeeeeeeeeeeees 114 57 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE Field IR le le Tis 58 Receive Unicast Enable Set Register RXUNICASTSET Field Descriptions 0 seceeeeeeeeeeeeeeeeeeeee 118 59 Receive Unicast Clear Register RXUNICASTCLEAR Field Descriptions cceeeeeeeeeeeeeeeeeeeeeeee 119 60 Receive Maximum Length Register RXMAXLEN Field Description 120 61 Receive Buffer Offset Register RXBUFFEROFFSET Field Descriptions 0 seceeeeeeeeeeeeeeeeeeeeeeee 121 62 Receive Filter Low Priority Frame Threshold Register RXFILTERLOWTHRESH Field Descriptions 122 63 Receive Channel n Flow Control Threshol
27. 5 22 Receive Unicast Enable Set Register RXUNICASTSET cceeeeeeeeee eee nese eee eee eee eeeeeeeeeeeeeeeeee 118 5 23 Receive Unicast Clear Register RXUNICASTCLEAR a 119 5 24 Receive Maximum Length Register RXMAXLEN AN 120 5 25 Receive Buffer Offset Register RXBUFFEROFFSET cseceeeeeeeeee ence eee eeeeeeee eee eeeeeeeeeeeeeneee 121 5 26 Receive Filter Low Priority Frame Threshold Register RXFILTERLOWTHRESH a 122 5 27 Receive Channel 0 7 Flow Control Threshold Register RXNFLOWTHRESH seeeeeeeeeeeeeeeeeeee 123 5 28 Receive Channel 0 7 Free Buffer Count Register RXnFREEBUFFER AN 124 5 29 MAC Control Register MACCONTROL ccceeee eee e eee e eect nena enna eee eee enna ee eeeaeeneeeeeeeeeneeeeeneee 125 5 30 MAC Status Register MACSTATUS ceceeeeeee eect eee eee eee eee nese eens tees teen eee eaeeeae eee eeeenaeeeeeee 127 5 31 Emulation Control Register EMCONTROL eeceeee cece eens eee eee e eee ee enna sees ease eee eeeneeenaeeeeeeee 129 5 32 FIFO Control Register FIFOCONTROL ccceeee eee ee cece e eee eee eee e nese eee ee seas teas eeeneeenae teenies 130 5 33 MAC Configuration Register MACCONFIG ceeceeee eee e erect eee e eee etna ee eee eee eae teat eee eeeenaeneeeeee 131 5 34 Soft Reset Register SOFTRESET ccsccseeeeeeeeeeeeeeeeeceneeeeeeeeseeeeeaeenaeeeeneeeeeeneeeeeeeaneaeeaee 132 5 35 MAC Source Address Low Bytes Register MACSRCADDRLO ecceeeeeee eee eee nese eee ee
28. 5 4 5 Packet Length This 16 bit field specifies the number of data bytes in the entire packet Any leading buffer offset bytes are not included The sum of the buffer length fields of each of the packet s fragments if more than one must be equal to the packet length The software application must set this value prior to adding the descriptor to the active transmit list This field is not altered by the EMAC This value is only checked on the first descriptor of a given packet where the SOP flag is set 2 5 4 6 Start of Packet SOP Flag When set this flag indicates that the descriptor points to a packet buffer that is the start of a new packet For a single fragment packet both the SOP and end of packet EOP flags are set Otherwise the descriptor pointing to the last packet buffer for the packet sets the EOP flag This bit is set by the software application and is not altered by the EMAC SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 35 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 5 4 7 End of Packet EOP Flag When set this flag indicates that the descriptor points to the last packet buffer for a given packet For a single fragment packet both the start of packet SOP and EOP flags are set Otherwise the descriptor pointing to the last packet buffer for the packet sets the EOP flag This bit is set b
29. Bit Field Value Description 31 16 Reserved 0 Reserved 15 0 RXBUFFEROFFSET Receive buffer offset value These bits are written by the EMAC into each frame SOP buffer descriptor Buffer Offset field The frame data begins after the RXBUFFEROFFSET value of bytes A value of 0 indicates that there are no unused bytes at the beginning of the data and that valid data begins on the first byte of the buffer A value of Fh 15 indicates that the first 15 bytes of the buffer are to be ignored by the EMAC and that valid buffer data starts on byte 16 of the buffer This value is used for all channels SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 121 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 26 Receive Filter Low Priority Frame Threshold Register RXFILTERLOWTHRESH The receive filter low priority frame threshold register RXFILTERLOWTHRESH is shown in Figure 68 and described in Table 62 Figure 68 Receive Filter Low Priority Frame Threshold Register RXFILTERLOWTHRESH 31 16 Reserved HO 15 8 7 0 Reserved RXFILTERTHRESH HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 62 Receive Filter Low Priority Frame Threshold Register RXFILTERLOWTHRESH Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reser
30. EMAC Registers continued Offset Acronym Register Description See 15Ch RX7FREEBUFFER Receive Channel 7 Free Buffer Count Register Section 5 28 160h MACCONTROL MAC Control Register Section 5 29 164h MACSTATUS MAC Status Register Section 5 30 168h EMCONTROL Emulation Control Register Section 5 31 16Ch FIFOCONTROL FIFO Control Register Section 5 32 170h MACCOMFIG MAC Configuration Register Section 5 33 174h SOFTRESET Soft Reset Register Section 5 34 1D0h MACSRCADDRLO MAC Source Address Low Bytes Register Section 5 35 1D4h MACSRCADDRHI MAC Source Address High Bytes Register Section 5 36 1D8h MACHASH1 MAC Hash Address Register 1 Section 5 37 1DCh MACHASH2 MAC Hash Address Register 2 Section 5 38 1E0h BOFFTEST Back Off Test Register Section 5 39 1E4h TPACETEST Transmit Pacing Algorithm Test Register Section 5 40 1E8h RXPAUSE Receive Pause Timer Register Section 5 41 1ECh TXPAUSE Transmit Pause Timer Register Section 5 42 500h MACADDRLO MAC Address Low Bytes Register Used in Receive Address Section 5 43 Matching 504h MACADDRHI MAC Address High Bytes Register Used in Receive Address Section 5 44 Matching 508h MACINDEX MAC Index Register Section 5 45 600h TXOHDP Transmit Channel 0 DMA Head Descriptor Pointer Register Section 5 46 604h TX1HDP Transmit Channel 1 DMA Head Descriptor Pointer Register Section 5 46 608h TX2HDP Transmit Channel 2 DMA Head Descriptor Pointer Register Section 5 46 60Ch TX3HDP Transmit Channel 3 DMA Head Descriptor Pointer
31. Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture Configuration register EMACCFG found at device level 20 Enable the device interrupt in EW_INTCTL 2 17 Interrupt Support 2 17 1 EMAC Module Interrupt Events and Requests The EMAC MDIO generates 18 interrupt events as follows e TXPENDn Transmit packet completion interrupt for transmit channels 7 through 0 e RXPENDn Receive packet completion interrupt for receive channels 7 through 0 e STATPEND Statistics interrupt e HOSTPEND Host error interrupt 2 17 1 1 Transmit Packet Completion Interrupts The transmit DMA engine has eight channels and each channel has a corresponding interrupt TXPENDn The transmit interrupts are level interrupts that remain asserted until cleared by the CPU Each of the eight transmit channel interrupts may be individually enabled by setting the appropriate bit in the TXINTMASKSET register Each of the eight transmit channel interrupts may be individually disabled by clearing the appropriate bit in the TXINTMASKCLEAR register The raw and masked transmit interrupt status may be read by reading the TXINTSTATRAW and TXINTSTATMASKED registers respectively When the EMAC completes the transmission of a packet the EMAC issues an interrupt to the CPU by writing the packet s last buffer descriptor address to the appropriate channel queue s TX completion pointer located in the sta
32. Mask Set Register TXINTMASKSET The transmit interrupt mask set register TXINTMASKSET is shown in Figure 51 and described in EMAC Port Registers Table 45 Figure 51 Transmit Interrupt Mask Set Register TXINTMASKSET 31 24 Reserved R 0 23 22 21 20 19 18 17 16 TX7PULSE TX6PULSE TX5PULSE TX4PULSE TX3PULSE TX2PULSE TX1PULSE TXOPULSE MASK MASK MASK MASK MASK MASK MASK MASK 15 Reserved R 0 7 6 5 4 3 2 1 0 TX7PEND TX6PEND TX5PEND TX4PEND TX3PEND TX2PEND TX1PEND TXOPEND MASK MASK MASK MASK MASK MASK MASK MASK LEGEND R W Read Write R Read only n value after reset Table 45 Transmit Interrupt Mask Set Register TXINTMASKSET Field Descriptions Bit Field Value Description 31 24 Reserved 0 Reserved read as 0 23 TX7PULSEMASK 0 Transmit channel 7 pulse interrupt mask Write 1 to enable interrupt 22 TX6PULSEMASK 0 Transmit channel 6 pulse interrupt mask Write 1 to enable interrupt 21 TX5PULSEMASK 0 Transmit channel 5 pulse interrupt mask Write 1 to enable interrupt 20 TX4PULSEMASK 0 Transmit channel 4 pulse interrupt mask Write 1 to enable interrupt 19 TX3PULSEMASK 0 Transmit channel 3 pulse interrupt mask Write 1 to enable interrupt 18 TX2PULSEMASK 0 Transmit channel 2 pulse interrupt mask Write 1 to enable interrupt 17 TX1PULSEMASK 0 Transmit channel 1 pulse interrupt mask Write
33. Port Registers A TEXAS INSTRUMENTS www ti com Table 65 MAC Control Register MACCONTROL Field Descriptions continued Bit Field Value Description 12 RXFIFOFLOWEN Receive FIFO flow control enable Receive flow control disabled For full duplex mode no outgoing pause frames are sent Receive flow control enabled For full duplex mode outgoing pause frames are sent when receive FIFO flow control is triggered 11 CMDIDLE Command Idle bit Idle not commanded Idle commanded read IDLE in the MACSTATUS register Reserved Reserved TXPTYPE Transmit queue priority type The queue uses a round robin scheme to select the next channel for transmission The queue uses a fixed priority channel 7 highest priority scheme to select the next channel for transmission Reserved Reserved GIG Gigabit mode Gigabit mode is disabled 10 100 mode is in operation Gigabit mode is enabled full duplex only TXPACE Transmit pacing enable bit Transmit pacing is disabled Transmit pacing is enabled GMIIEN GMII enable bit GMII RX and TX are held in reset GMII RX and TX are enabled for receive and transmit TXFLOWEN Transmit flow control enable bit This bit determines if incoming pause frames are acted upon in full duplex mode Incoming pause frames are not acted upon in half duplex mode regardless of this bit setting The RXMBPENABLE bits determine whether or not received pau
34. R W 0 LEGEND R W Read Write R Read only n value after reset Table 38 Transmit Control Register TXCONTROL Field Descriptions Bit Field Value Description 31 1 Reserved 0 Reserved 0 TXEN Transmit enable 0 Transmit is disabled Transmit is enabled 96 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 3 Transmit Teardown Register TXTEARDOWN The transmit teardown register TXTEARDOWN is shown in Figure 45 and described in Table 39 Figure 45 Transmit Teardown Register TXTEARDOWN 31 30 16 TXTD NRDY Reserved HO 15 3 2 0 Reserved TXTDNCH HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 39 Transmit Teardown Register TXTEARDOWN Field Descriptions Bit Field Value Description 31 TXTDNRDY 0 Transmit teardown ready Read as zero but is always assumed to be one unused 30 3 Reserved 0 Reserved 2 0 TXTDNCH Transmit teardown channel The transmit teardown channel is commanded by writing the encoded value of the transmit channel to be torn down The teardown register is read as zero 0 Teardown transmit channel 0 th Teardown transmit channel 1 2h Teardown transmit channel 2 3h Teardown transmit channel 3 4h Teardown transmit channel 4 5h Teardown tran
35. RXCH2EN RXCH1EN RXCHOEN R 0 R WC 0 R WC 0 R WC 0 R WC 0 R WC 0 R WC 0 R WC 0 R WC 0 LEGEND R Read only R W Read Write R WC Read Write 1 to clear n value after reset Table 59 Receive Unicast Clear Register RXUNICASTCLEAR Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 RXCH7EN Receive channel 7 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 6 RXCH6EN Receive channel 6 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 5 RXCH5EN Receive channel 5 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 4 RXCH4EN Receive channel 4 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 3 RXCH3EN Receive channel 3 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 2 RXCH2EN Receive channel 2 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 1 RXCH1EN Receive channel 1 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect 0 RXCHOEN Receive channel 0 unicast enable clear bit Write 1 to clear the enable a write of 0 has no effect SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 119 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS EMAC Port Registers www ti com
36. RXMULTCH 0 3h Receive multicast channel select 0 Select channel 0 to receive multicast frames th Select channel 1 to receive multicast frames 2h Select channel 2 to receive multicast frames 3h Select channel 3 to receive multicast frames 4h Select channel 4 to receive multicast frames 5h Select channel 5 to receive multicast frames 6h Select channel 6 to receive multicast frames 7h Select channel 7 to receive multicast frames SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated C6472 TCI6486 EMAC MDIO 117 I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 22 Receive Unicast Enable Set Register RXUNICASTSET The receive unicast enable set register RXUNICASTSET is shown in Figure 64 and described in Table 58 Figure 64 Receive Unicast Enable Set Register RXUNICASTSET 31 16 Reserved R 0 15 8 7 6 5 4 3 2 1 0 Reserved RXCH7EN RXCHG6EN RXCH5EN RXCH4EN RXCH3EN RXCH2EN RXCH1EN RXCHOEN H R WS 0 R WS 0 R WS 0 R WS 0 R WS 0 R WS 0 R WS 0 R WS 0 LEGEND R Read only R W Read Write R WS Read Write 1 to set n value after reset Table 58 Receive Unicast Enable Set Register RXUNICASTSET Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 RXCH7EN Receive channel 7 unicast enable set bit Write 1 to set th
37. TXINTMASKSET cceeceeee cece eens eens eee eeeeeeeeeeeeeeeeeeeeees 103 5 10 Transmit Interrupt Mask Clear Register TXINTMASKCLEAR 0 seeceeeeeeeeeeee eens tees eeeeeeeeeeeeeeeee 104 5 11 MAC Input Vector Register MACINVECTOR ceeceeee cece eee ee eee e eect eee ee enna sees ease neeeeeeeeeaeeeneeee 105 5 12 MAC Ena of Interrupt Vector Register MACEOIVECTOR cceeeeeeeee ences eee eee eee teen eeeeeeeeeeneeeeee 106 5 13 Receive Interrupt Status Unmasked Register RXINTSTATRAW 0ceeceeee eee eee eect eeeeeeeeeeeeeeeee 107 5 14 Receive Interrupt Status Masked Register RXINTSTATMASKED 0cceeeeee eect eee ee seen eee eeeeeee 108 5 15 Receive Interrupt Mask Set Register RXINTMASKSET ecceeee eee ee erect eee ee eee eeeeeeeeeeeeeeeeeeeee 109 5 16 Receive Interrupt Mask Clear Register RXINTMASKCLEAR 0eeeeeeee eee ee sees sees eeeeeeeeeneeeeeee 110 5 17 MAC Interrupt Status Unmasked Register MACINTSTATRAW ccceeeeeee eee eee eee eeeeeeeneeeeeeeee 111 5 18 MAC Interrupt Status Masked Register MACINTSTATMASKED aauusssssssssnnnerrrnrrrnrrnnnnnnnnrennnne 112 5 19 MAC Interrupt Mask Set Register MACINTMASKSET cceeeeeee eens ence eee e eee eee sees eeeeeeeeaeeeeneee 113 5 20 MAC Interrupt Mask Clear Register MACINTMASKCLEAR eceeeeeeeeee eee eee eee eeeeeeeeeeenaeneeeeee 114 5 21 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE 115
38. addresses Application software uses the MDIO module to configure the auto negotiation parameters of the primary PHY attached to the EMAC retrieve the negotiation results and configure required parameters in the EMAC Up to two Ethernet PHYs can be directly controlled and queried The Media Independent Interface addresses of these two PHY devices are specified in the PHYADRMON fields of the USERPHYSELn register The module can be programmed to trigger a CPU interrupt on a PHY link change event by setting the LINKINTENB bit in USERPHYSELn Reads and writes to registers in these PHY devices are performed using the USERACCESSn register The MDIO module powers up in an idle state until it is enabled by setting the ENABLE bit in the CONTROL register This also configures the MDIO clock divider and preamble mode selection The MDIO preamble is enabled by default but it can be disabled if none of the connected PHYs require it Once the MDIO module is enabled the MDIO interface state machine continuously polls the PHY link status by reading the generic PHY Status register of all possible 32 PHY addresses and records the results in the ALIVE and LINK registers The corresponding bit for each PHY 0 31 is set in the ALIVE register if the PHY responded to the read request The corresponding bit is set in the LINK register if the PHY responded and also is currently linked In addition any PHY register read transactions initiated by the application software
39. buffer descriptor Figure 12 is a contiguous block of four 32 bit data words aligned on a 32 bit boundary that describes a packet or a packet fragment Example 1 shows the transmit buffer descriptor described by a C structure Figure 12 Transmit Descriptor Format a Word 0 31 0 Next Descriptor Pointer b Word 1 31 0 Buffer Pointer c Word 2 31 16 15 H Buffer Offset Buffer Length d Word 3 31 30 29 28 27 26 25 16 TDOWN PASS SOP EOP OWNER EOQ CMPLT CRC Reserved 15 Q Packet Length Example 1 Transmit Descriptor in C Structure Format Wi define define define define define define Uint32 Uint32 EMAC_Desc EMAC Descriptor Packet Flags EMAC_DSC_FLAG_SOP EMAC_DSC_FLAG_EOP EMAC_DSC_FLAG_OWNER EMAC_DSC_FLAG_EOQ EMAC_DSC_FLAG_TDOWNCMPLT EMAC_DSC_FLAG_PASSCRC The following is the format on the EMAC typedef struct _EMAC_Desc struct _EMAC_Desc pNext Uint8 pBuffer BufOffLen PktFlgLen of a single buffer descriptor Pointer to next descriptor in chain Pointer to data buffer Buffer Offset MSW Packet Flags MSW 0x80000000u 0x40000000u 0x20000000u 0x10000000u 0x08000000u 0x04000000u and Length LSW and Length LSW 34 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Copyright 2006 2010 Texas Instruments Incorporated Submit Documentation Feedback 1 TEXAS INSTRUM
40. certain multicast addresses on a network to reduce traffic load The multicast address list of acceptable packets is specified by the application Physical Layer and Media Notation To identify different Ethernet technologies a simple three field type notation is used The Physical Layer type used by the Ethernet is specified by these fields lt data rate in Mb s gt lt medium type gt lt maximum segment length x100m gt The definitions for the technologies mentioned in this guide are as follows Term Definition 10Base T IEEE 802 3 Physical Layer specification for a 10 Mb s CSMA CD local area network over two pairs of twisted pair telephone wire 100Base T IEEE 802 3 Physical Layer specification for a 100 Mb s CSMA CD local area network over two pairs of Category 5 unshielded twisted pair UTP or shielded twisted pair STP wire 1000Base T IEEE 802 3 Physical Layer specification for a 1000 Mb s CSMA CD LAN using four pairs of Category 5 balanced copper cabling Twisted pair A cable element that consists of two insulated conductors twisted together in a regular fashion to form a balanced transmission line Port Ethernet device Promiscuous Mode EMAC receives frames that do not match its address 158 Glossary SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Appendix B Revision History This revisio
41. counter is nonzero the frame is delayed by a pacing delay of approximately four inter packet gap delays APO only affects the IPG preceding the first attempt at transmitting a frame APO does not affect the back off algorithm for re transmitted frames 2 10 2 4 Interpacket Gap IPG Enforcement 56 The measurement reference for the IPG of 96 bit times is changed depending on frame traffic conditions If a frame is successfully transmitted without collision and MCRS is de asserted within approximately 48 bit times of MTXEN being de asserted then 96 bit times is measured from MTXEN If the frame suffered a collision or MCRS is not de asserted until more than approximately 48 bit times after MTXEN is de asserted then 96 bit times approximately but not less is measured from MCRS C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 10 2 5 Back Off The EMAC implements the 802 3 binary exponential back off algorithm 2 10 2 6 Transmit Flow Control When enabled incoming pause frames are acted upon to prevent the EMAC from transmitting any further frames Incoming pause frames are only acted upon when the FULLDUPLEX and TXFLOWEN bits in the MACCONTROL register are set Pause frames are not acted upon in half duplex mode Pause frame action is taken if enabled but normally th
42. determine if the interrupt was due to a commanded teardown The read value is FFFF FFFCh if the interrupt was due to a teardown command 2 11 7 Receive Frame Classification Received frames are proper or good frames if they are between 64 and RXMAXLEN in length inclusive and contain no code align or CRC errors Received frames are long frames if their frame count exceeds the value in the RXMAXLEN register The RXMAXLEN register default reset value is 5EEh 1518 in decimal Long received frames are either oversized or jabber frames Long frames with no errors are oversized frames long frames with CRC code or alignment errors are jabber frames Received frames are short frames if their frame count is less than 64 bytes Short frames that address match and contain no errors are undersized frames short frames with CRC code or alignment errors are fragment frames If the frame length is less than or equal to 20 then the frame CRC is passed regardless of whether the RXPASSCRC bit is set or cleared in the RXMBPENABLE register A received long packet always contains RXMAXLEN number of bytes transferred to memory if the RXCEFEN bit is set in RXMBPENABLE regardless of the value of the RXPASSCRC bit Following is an example with RXMAXLEN set to 1518 e Ifthe frame length is 1518 then the packet is not a long packet and there are 1514 or 1518 bytes transferred to memory depending on the value of the RXPASSCRC bit e Ifthe frame length is
43. e Did not experience late collisions excessive collisions underrun or carrier sense error e Was exactly 64 bytes long If the frame was being transmitted and experienced carrier loss that resulted in a frame of this size being transmitted then the frame is recorded in this statistic CRC errors alignment code errors and overruns do not affect the recording of frames in this statistic 5 50 28 Transmit and Receive 65 to 127 Octet Frames Register FRAME65T127 The total number of 65 byte to 127 byte frames received and transmitted on the EMAC Such a frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Did not experience late collisions excessive collisions underrun or carrier sense error e Was 65 bytes to 127 bytes long CRC errors alignment code errors underruns and overruns do not affect the recording of frames in this Statistic 5 50 29 Transmit and Receive 128 to 255 Octet Frames Register FRAME128T255 154 The total number of 128 byte to 255 byte frames received and transmitted on the EMAC Such a frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Did not experience late collisions excessive collisions underrun or carrier sense error e Was 128 bytes to 255 bytes long CRC errors alignment code errors underruns and overru
44. error occurred on receive channel 1 2h The host error occurred on receive channel 2 3h The host error occurred on receive channel 3 4h The host error occurred on receive channel 4 5h The host error occurred on receive channel 5 6h The host error occurred on receive channel 6 7h The host error occurred on receive channel 7 7 5 Reserved 0 Reserved RGMIIGIG RGMII gigabit This is the value of RGMIIGIG input 3 RGMIIFULLDUPLEX RGMII full duplex This is the value of RGMIIFULLDUPLEX input 2 RXQOSACT Receive Quality of Service QOS active bit When asserted indicates that receive quality of service is enabled and that at least one channel freebuffer count RXnFREEBUFFER is less than or equal to the RXFILTERLOWTHRESH value 0 Receive quality of service is disabled 1 Receive quality of service is enabled 1 RXFLOWACT Receive flow control active bit When asserted indicates that at least one channel freebuffer count RXnFREEBUFFER is less than or equal to the channel s corresponding RXnFILTERTHRESH value 0 Receive flow control is inactive 1 Receive flow control is active 0 TXFLOWACT Transmit flow control active bit When asserted this bit indicates that the pause time period is being observed for a received pause frame No new transmissions will begin while this bit is asserted except for the transmission of pause frames Any transmission in progress when this bit is asserted will complete 0 Transmit flow control is inactive 1 Transmit
45. flow control is active 128 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 31 Emulation Control Register EMCONTROL The emulation control register EMCONTROL is shown in Figure 73 and described in Table 67 Figure 73 Emulation Control Register EMCONTROL 31 16 Reserved R 0 15 2 1 0 Reserved SOFT FREE HO R W 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 67 Emulation Control Register EMCONTROL Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 SOFT Emulation soft bit 0 FREE Emulation free bit SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 129 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 32 FIFO Control Register FIFOCONTROL The FIFO control register FIFOCONTROL is shown in Figure 74 and described in Table 68 Figure 74 FIFO Control Register FIFOCONTROL 31 23 22 16 Reserved RXFIFOFLOWTHRESH HO R W 2 15 5 4 0 Reserved TXCELLTHRESH R 0 R W 24 LEGEND R W Read Write R Read only n value after reset Table 68 FIFO Control Register FIFOCONTROL Field Descriptions
46. immediately follows the preamble pattern and indicates Delimiter the start of important data Destination 6 This field contains the Ethernet MAC address of the intended EMAC port for the frame address It may be an individual or multicast including broadcast address If the destination EMAC port receives an Ethernet frame with a destination address that does not match any of its MAC physical addresses and no promiscuous multicast or broadcast channel is enabled it discards the frame Source 6 This field contains the MAC address of the Ethernet port that transmits the frame to the address Local Area Network Len 2 The length field indicates the number of EMAC client data bytes contained in the subsequent data field of the frame This field can also be used to identify the data type carried by the frame Data 46 to RXMAXLEN 18 This field carries the datagram containing the upper layer protocol frame the IP layer datagram The maximum transfer unit MTU of Ethernet is RXMAXLEN 18 bytes Therefore if the upper layer protocol datagram exceeds RXMAXLEN 18 bytes the host must fragment the datagram and send it in multiple Ethernet packets The minimum size of the data field is 46 bytes Thus if the upper layer datagram is less then 46 bytes the data field must be extended to 46 bytes by appending extra bits after the data field but prior to calculating and appending the FCS Frame Check 4 A cyclic redundancy check CRC is used by
47. in the RAM are enabled by the RXUNICASTSET register and not by the RXMULTEN bit in the RXMBPENABLE register The RXMULTEN bit enables the hash multicast match only The address RAM takes precedence over the hash match If a multicast packet is received that hash matches multicast packets enabled but is filtered in the RAM then the packet is filtered If a multicast packet does not hash match regardless of whether or not hash matching is enabled but matches an enabled multicast address in the RAM then the packet will be transferred to the associated channel Receive Channel Addressing The receive address block can store up to 32 addresses to be filtered or matched Before enabling packet reception all the address RAM locations should be initialized including locations to be unused The system software is responsible for adding and removing addresses from the RAM C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 11 4 2 11 5 A MAC address location in RAM is 53 bits wide and consists of e 48 bits of the MAC address e 3 bits for the channel to which a valid address match will be transferred The channel is a don t care if the MATCHFILT bit is cleared e A valid bit e A match or filter bit First write the index into the address RAM in the MACINDEX register
48. interrupt combiner Figure 20 Common Interrupt Combiner Common interrupt combiner block HOST EW_INTCTL 1 STAT EW_INTCTL 2 MACINT MDIO_LINT EW_INTCTL 3 MDIO_USER EW_INTCTL 4 EW_INTCTL 4 1 Management Data Input Output MDIO Module The Management Data Input Output MDIO module manages up to 32 physical layer PHY devices connected to the Ethernet Media Access Controller EMAC The MDIO module allows almost transparent operation of the MDIO interface with little maintenance from the CPU The MDIO module enumerates all PHY devices in the system by continuously polling 32 MDIO addresses Once it detects a PHY device the MDIO module reads the PHY status register to monitor the PHY link state The MDIO module stores link change events that can interrupt the CPU The event storage allows the CPU to poll the link status of the PHY device without continuously performing MDIO module accesses However when the system must access the MDIO module for configuration and negotiation the MDIO module performs the MDIO read or write operation independent of the CPU This independent operation allows the DSP to poll for completion or interrupt the CPU once the operation has completed MDIO Module Components The MDIO module shown in Figure 21 interfaces to PHY components through two MDIO pins MDCLK and MDIO and to the DSP core through the EMIC module and the configuration bus The MDIO module consists of the following lo
49. is used as an offset into a 64 bit hash table stored in MACHASH1 and MACHASH2 that indicates whether a particular address should be accepted or not The MAC hash address register 1 MACHASH1 is shown in Figure 79 and described in Table 73 Figure 79 MAC Hash Address Register 1 MACHASH1 31 16 MACHASH1 R W 0 15 0 MACHASH1 R W 0 LEGEND R W Read Write n value after reset Table 73 MAC Hash Address Register 1 MACHASH1 Field Descriptions Bit Field Value Description 31 0 MACHASH1 Least significant 32 bits of the hash table corresponding to hash values 0 to 31 If a hash table bit is set then a group address that hashes to that bit index is accepted SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 135 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 38 MAC Hash Address Register 2 MACHASH2 The MAC hash address register 2 MACHASH2 is shown in Figure 80 and described in Table 74 Figure 80 MAC Hash Address Register 2 MACHASH2 31 16 MACHASH2 R W 0 15 0 MACHASH2 R W 0 LEGEND R W Read Write n value after reset Table 74 MAC Hash Address Register 2 MACHASH2 Field Descriptions Bit Field Value Description 31 0 MACHASH2 Most significant 32 bits of the hash table corresponding to hash values 32 to 63 If a hash ta
50. of Ethernet utilization SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 155 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 50 34 Receive FIFO or DMA Sitart of Frame Overruns Register RXSOFOVERRUNS The total number of frames received on the EMAC that had either a FIFO or DMA start of frame SOF overrun An SOF overrun frame is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of any size including less than 64 byte and greater than RXMAXLEN byte frames e The EMAC was unable to receive it because it did not have the resources to receive it cell FIFO full or no DMA buffer available at the start of the frame CRC errors alignment errors and code errors have no effect on this statistic 5 50 35 Receive FIFO or DMA Middle of Frame Overruns Register RXMOFOVERRUNS The total number of frames received on the EMAC that had either a FIFO or DMA middle of frame MOF overrun An MOF overrun frame is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of any size including less than 64 byte and greater than RXMAXLEN byte frames e The EMAC was unable to receive it because it
51. pause timer immediately expires The EMAC does not start the transmission of a new data frame any sooner than 512 bit times after a pause frame with a non zero pause time has finished being received MRXDV going inactive No transmission begins until the pause timer has expired the EMAC may transmit pause frames to initiate outgoing flow control Any frame already in transmission when a pause frame is received is completed and unaffected Incoming pause frames consist of e A 48 bit destination address equal to one of the following The reserved multicast destination address 01 80 C2 00 00 01h Any EMAC 48 bit unicast address Pause frames are accepted regardless of whether the channel is enabled e The 48 bit source address of the transmitting device e The 16 bit length type field containing the value 88 08h e The 16 bit pause opcode equal to 00 01h e The 16 bit pause time A pause quantum is 512 bit times e Padding to 64 byte data length e The 32 bit frame check sequence CRC word All quantities are hexadecimal and are transmitted most significant byte first The least significant bit LSB is transferred first in each byte The padding is required to make up the frame to a minimum of 64 bytes The standard allows pause frames longer than 64 bytes to be discarded or interpreted as valid pause frames The EMAC recognizes any pause frame between 64 bytes and RXMAXLEN bytes in length SPRUEF8F March 2006 Revised November
52. rules e For the short term average each 64 byte memory read write request from the EMAC must be serviced in no more than 0 512 us e Any single latency event in request servicing can be no longer than 0 512 TXCELLTHRESH us Bits 0 2 of the PRI_ALLOC register set the transfer node priority for EMACO in the device Bits 12 14 of the PRI_ALLOC register set the transfer node priority for EMAC1 in the device A value of 000b has the highest priority while 111b has the lowest The default priority assigned to EMACO and EMAC 1 is 111b It is important to have a balance between all peripherals In most cases the default priorities will not need adjustment 2 15 Reset Considerations 2 15 1 2 15 2 2 15 3 Software Reset Considerations For information on the chip level reset capabilities of various peripherals see the TMS320TCI6486 Communications Infrastructure Digital Signal Processor data manual SPRS300 or the 7MS320C6472 Fixed Point Digital Signal Processor data manual SPRS612 Within the peripheral itself the EMAC component of the Ethernet MAC peripheral can be placed in a reset state by writing to the SOFTRESET register located in EMAC memory map Writing a one to bit 0 of this register causes the EMAC logic to be reset and the register values to be set to their default values Software reset occurs when the receive and transmit DMA controllers are in an idle state to avoid locking up the configuration bus it is the respo
53. the descriptor s next pointer is NULL allowing the EMAC to indicate to the software application that it has reached the end of the list When the software application sees the EOQ flag set and there are more descriptors to process the application may then submit the new list or missed list portion by writing the new list pointer to the same HDP register that started the process This process applies when adding packets to a transmit list and empty buffers to a receive list Transmit and Receive EMAC Interrupts The EMAC processes descriptors in linked list chains Section 2 5 1 using the linked list queue mechanism Section 2 5 2 The EMAC synchronizes the descriptor list processing by using interrupts to the software application The interrupts are controlled by the application by using the interrupt masks global interrupt enable and the completion pointer register CP This register is also called interrupt acknowledge register As the EMAC supports eight channels for both transmit and receive there are eight CP registers for both They are designated as e TXnCP Transmit Channel n Completion Pointer Interrupt Acknowledge Register e RXnCP Receive Channel n Completion Pointer Interrupt Acknowledge Register These registers serve two purposes When read they return the pointer to the last descriptor that the EMAC has processed When written by the software application the value represents the last descriptor processed by the
54. to be a register write otherwise it is a register read 0 The user command is a read operation The user command is a write operation 29 ACK Acknowledge bit This bit is set if the PHY acknowledged the read transaction 28 26 Reserved 0 Reserved 25 21 REGADR Register address bits This field specifies the PHY register to be accessed for this transaction 20 16 PHYADR PHY address bits This field specifies the PHY to be accessed for this transaction 15 0 DATA User data bits These bits specify the data value read from or to be written to the specified PHY register SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 89 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS MDIO Registers www ti com 4 15 MDIO User PHY Select Register 1 USERPHYSEL1 The MDIO user PHY select register 1 USERPHYSEL1 is shown in Figure 42 and described in Table 35 Figure 42 MDIO User PHY Select Register 1 USERPHYSEL1 31 16 Reserved HO 15 8 7 6 5 4 0 Reserved LINKSEL LINKINTENB Reserved PHYADRMON HO R W 0 R W 0 HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 35 MDIO User PHY Select Register 1 USERPHYSEL1 Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 LINKSEL Link status determination select bit De
55. to start writing a MAC address Then write the upper 32 bits of the MAC address MACADDRHI register and then the lower 16 bits of MAC address with the VALID and MATCHFILT control bits MACADDRLO The valid bit should be cleared for the unused locations in the receive address RAM The most common uses for the receive address sub module are e Set EMAC in promiscuous mode using the RXCAFEN and RXPROMCH bits in the RXMBPENABLE register Then filter up to 32 individual addresses which can be both unicast and or multicast e Disable the promiscuous mode RXCAFEN 0 and match up to 32 individual addresses multicast and or unicast Hardware Receive QOS Support Hardware receive quality of service QOS is supported when enabled by the Tag Protocol Identifier format and the associated Tag Control Information TCI format priority field When the incoming frame length type value is equal to 81 00h the EMAC recognizes the frame as an Ethernet Encoded Tag Protocol Type The two octets immediately following the protocol type contain the 16 bit TCI field Bits 15 13 of the TCI field contain the received frames priority 0 to 7 The received frame is a low priority frame if the priority value is 0 to 3 The received frame is a high priority frame if the priority value is 4 to 7 All frames that have a length type field value not equal to 81 00h are low priority frames Received frames that contain priority information are determined by the EMAC as
56. transmit channel the host error occurred This field is cleared to 0 on a host read 0 The host error occurred on transmit channel 0 th The host error occurred on transmit channel 1 2h The host error occurred on transmit channel 2 3h The host error occurred on transmit channel 3 4h The host error occurred on transmit channel 4 5h The host error occurred on transmit channel 5 6h The host error occurred on transmit channel 6 7h The host error occurred on transmit channel 7 SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 127 Copyright 2006 2010 Texas Instruments Incorporated EMAC Port Registers A TEXAS INSTRUMENTS www ti com Table 66 MAC Status Register MACSTATUS Field Descriptions continued Bit Field Value Description 15 12 RXERRCODE Receive host error code These bits indicate that EMAC detected receive DMA related host errors The host should read this field after a host error interrupt HOSTPEND to determine the error Host error interrupts require a hardware reset in order to recover 0 No error 2h Ownership bit not set in SOP buffer 4h Zero buffer pointer 11 Reserved 0 Reserved 10 8 RXERRCH 0 3h Receive host error channel These bits indicate on which receive channel the host error occurred This field is cleared to 0 on a host read 0 The host error occurred on receive channel 0 th The host
57. two sets of pins associated with serial management interface One serial management interface is for RGMII needed at 1 8 V HSTL buffer and the other serial management interface is for non RGMII interfaces needed at 3 3 V LVCMOS buffers Table 1 Serial Management Interface Pins Signal Description GMDCLK MII GMII RMII S3MII management clock Available on 3 3 V LVCMOS buffers GMDIO MII GMII RMII S3MII management data Available on 3 3 V LVCMOS buffers RGMDCLK RGMII management clock Available on 1 8 V HSTL buffers RGMDIO RGMII management data Available on 1 8 V HSTL buffers As mentioned above the management interface selection is based on the interface selection for EMACO If MACSELO is programmed to select RGMIIO the 1 8 V serial management interface is selected RGMDIO RGMDCLK otherwise the 3 3 V GMDIO GMDCLK management interface is selected Due to this programmed selection in some cases level shifters may have to be used for the management interface As an example if the RGMIIO interface is selected for EMACO and the S3MII1 interface is selected for EMAC1 the 1 8 V serial management interface RGMDCLK and RGMDIO is used Since S3MII PHY needs the 3 3 V management interface level shifters have to be used to level translate these HSTL pins Also note that EMAC1 can be enabled or disabled using the EMAC1_EN internal pulldown pin that controls the I O signals of EMAC1 The EMAC1_EN is also latched into the bit 12 of
58. was detected in the received frame This is meaningful only during data reception when MRXDV is active MDCLK O Management data clock MDCLK The MDIO data clock is sourced by the MDIO module on the system Itis used to synchronize MDIO data access operations done on the MDIO pin The frequency of this clock is controlled by the CLKDIV bits in the MDIO control register CONTROL MDIO UO Management data input output MDIO The MDIO pin drives PHY management data into and out of the PHY by way of an access frame consisting of start of frame read write indication PHY address register address and data bit cycles The MDIO pin acts as an output for everything except the data bit cycles when the pin acts as an input for read operations When the device is interfaced to an Ethernet switch via an MIl interface the carrier sense MCRS and collision MCOL signals are not necessary since full duplex operation is forced On the TC16486 C6472 device the MII Ethernet interface is available only on EMACO MIIO pins are multiplexed with other non RGMII pins RMII1 S3MII1 due to this multiplexing when the MIIO interface is selected on EMACO except for RGMII1 no Ethernet interface is available on EMAC1 SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 19 Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 3 2 Reduce
59. www ti com lprf Video and Imaging www ti com video Wireless www ti com wireless apps Mailing Address Texas Instruments Post Office Box 655303 Dallas Texas 75265 Copyright 2010 Texas Instruments Incorporated
60. 1 EMAC Port Registers Figure 72 MAC Status Register MACSTATUS 24 IDLE Reserved R 0 R 0 23 20 19 18 16 TXERRCODE Reserved TXERRCH R 0 R 0 15 12 11 10 8 RXERRCODE Reserved RXERRCH R 0 R 0 7 5 4 3 2 1 0 Reserved RDMIIGIG RGMIIFULLDUPLEX RXQOSACT RXFLOWACT TXFLOWACT R x R x R 0 R 0 R 0 LEGEND R W Read Write R Read only n value after reset Table 66 MAC Status Register MACSTATUS Field Descriptions Bit Field Value Description 31 IDLE EMAC idle bit This bit is set to 0 at reset one clock after reset it goes to 1 0 The EMAC is not idle 1 The EMAC is in the idle state 30 24 Reserved 0 Reserved 23 20 TXERRCODE Transmit host error code These bits indicate that EMAC detected transmit DMA related host errors The host should read this field after a host error interrupt HOSTPEND to determine the error Host error interrupts require a hardware reset in order to recover A zero packet length is an error but it is not detected 0 No error th SOP error the buffer is the first buffer in a packet but the SOP bit is not set in software 2h Ownership bit not set in SOP buffer 3h Zero next buffer descriptor pointer without EOP 4h Zero buffer pointer 5h Zero buffer length 6h Packet length error sum of buffers lt packet length 19 Reserved 0 Reserved 18 16 TXERRCH 0 3h Transmit host error channel These bits indicate on which
61. 1 to enable interrupt 16 TXOPULSEMASK 0 Transmit channel 0 pulse interrupt mask Write 1 to enable interrupt 15 8 Reserved 0 Reserved read as 0 7 TX7PENDMASK 0 Transmit channel 7 pending interrupt mask Write 1 to enable interrupt 6 TX6PENDMASK 0 Transmit channel 6 pending interrupt mask Write 1 to enable interrupt 5 TX5PENDMASK 0 Transmit channel 5 pending interrupt mask Write 1 to enable interrupt 4 TX4PENDMASK 0 Transmit channel 4 pending interrupt mask Write 1 to enable interrupt 3 TX3PENDMASK 0 Transmit channel 3 pending interrupt mask Write 1 to enable interrupt 2 TX2PENDMASK 0 Transmit channel 2 pending interrupt mask Write 1 to enable interrupt 1 TX1PENDMASK 0 Transmit channel 1 pending interrupt mask Write 1 to enable interrupt 0 TXOPENDMASK 0 Transmit channel 0 pending interrupt mask Write 1 to enable interrupt SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO Copyright 2006 2010 Texas Instruments Incorporated 103 EMAC Port Registers 5 10 Transmit Interrupt Mask Clear Register TXINTMASKCLEAR The transmit interrupt mask clear register TXINTMASKCLEAR is shown in Figure 52 and described in l TEXAS INSTRUMENTS www ti com Table 46 Figure 52 Transmit Interrupt Mask Clear Register TXINTMASKCLEAR 31 24 Reserved R 0 23 22 21 20 19 18 17 16 TX7PULSE TX6PULSE TX5PULSE TX4PULSE TX3
62. 10 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 29 MAC Control Register MACCONTROL The MAC control register MACCONTROL is shown in Figure 71 and described in Table 65 31 Figure 71 MAC Control Register MACCONTROL 24 Reserved HO 23 19 18 17 16 Reserved RGMIIEN GIGFORCE RMIIDUPLEXMODE R 0 R W 0 R W 0 R W 0 15 14 13 12 11 10 9 8 RMIISPEED RXOFFLENBLOCK RXOWNERSHIP GE CMDIDLE Reserved TXPTYPE Reserved R W 0 R W 0 R W 0 R W 0 R W 0 R 0 R W 0 R 0 7 6 5 4 3 2 1 0 GIG TXPACE GMIIEN TXFLOWEN RXBUFFERFLOWEN Reserved LOOPBACK FULLDUPLEX R W 0 R W 0 R W 0 R W 0 R W 0 R 0 R W 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 65 MAC Control Register MACCONTROL Field Descriptions Bit Field Value Description 31 19 Reserved 0 Reserved 18 RGMIIEN RGMII enable bit Enables the fullduplex and gigabit mode to be selected from the RGMIIFULLDUPLEX and RGMIIGIG input signals and not from the FULLDUPLEX and GIG bits contained in this register This bit is directly connected to the RXINBAND input on the RGMII module 0 The RGMII interface is in forced link mode The duplexity is determined by the FULLDUPLEX bit and the speed is determined by the GIG bit The speed is either 1 Gbps or 100 Mbps 10 Mbps is not supported in forced link mode 1 The RGMII interface requires and use
63. 10 Texas Instruments Incorporated 55 I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 10 2 e Zero padding to 64 byte data length EMAC transmits only 64 byte pause frames e The 32 bit frame check sequence CRC word All quantities are hexadecimal and are transmitted most significant byte first The least significant bit LSB is transferred first in each byte If the RXBUFFERFLOWEN bit in the MACCONTROL register is cleared while the pause time is nonzero then the pause time is cleared and a zero count pause frame is sent Data Transmission The EMAC passes data to the PHY from the transmit FIFO when enabled Data is synchronized to the transmit clock rate Transmission begins when there are TXCELLTHRESH cells of 64 bytes each or a complete packet in the FIFO 2 10 2 1 Transmit Control A jam sequence is output if a collision is detected on a transmit packet If the collision was late after the first 64 bytes have been transmitted the collision is ignored If the collision is not late the controller will back off before retrying the frame transmission When operating in full duplex mode the carrier sense MCRS and collision sensing MCOL modes are disabled 2 10 2 2 CRC Insertion If the SOP buffer descriptor PASSCRC flag is cleared the EMAC generates and appends a 32 bit Ethernet CRC onto the transmitted data For the EMAC generated CRC case a CRC or placeholder at the end of the data is allowed
64. 1519 there are 1518 bytes transferred to memory regardless of the RXPASSCRC bit value The last three bytes are the first three CRC bytes e Ifthe frame length is 1520 there are 1518 bytes transferred to memory regardless of the RXPASSCRC bit value The last two bytes are the first two CRC bytes e Ifthe frame length is 1521 there are 1518 bytes transferred to memory regardless of the RXPASSCRC bit value The last byte is the first CRC byte e Ifthe frame length is 1522 there are 1518 bytes transferred to memory The last byte is the last data byte 60 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 11 8 Promiscuous Receive Mode When the promiscuous receive mode is enabled by setting the RXCAFEN bit in the RXMBPENABLE register non address matching frames that would normally be filtered are transferred to the promiscuous channel Address matching frames that would normally be filtered due to errors are transferred to the address match channel when the RXCAFEN and RXCEFEN bits are set Address matching frames with the filter bit set MATCHFILT 0 are always filtered regardless of the RXCAFEN and RXCEFEN bit setting A frame is considered to be an address matching frame only if it is enabled to be received on a unicast multicast or broadcast channel Frames received t
65. 24TUP The total number of 1024 byte to RXMAXLEN byte frames received and transmitted on the EMAC Such a frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Did not experience late collisions excessive collisions underrun or carrier sense error e Was 1024 bytes to RXMAXLEN bytes long CRC alignment code errors underruns and overruns do not affect frame recording in this statistic 5 50 33 Network Octet Frames Register NETOCTETS The total number of bytes of frame data received and transmitted on the EMAC Each frame counted has all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address address match does not matter e Was of any size including less than 64 byte and greater than RXMAXLEN byte frames Also counted in this statistic is e Every byte transmitted before a carrier loss was experienced e Every byte transmitted before each collision was experienced multiple retries are counted each time e Every byte received if the EMAC is in half duplex mode until a jam sequence was transmitted to initiate flow control The jam sequence is not counted to prevent double counting Error conditions such as alignment errors CRC errors code errors overruns and underruns do not affect the recording of bytes in this statistic The objective of this statistic is to give a reasonable indication
66. 5 24 Receive Maximum Length Register RXMAXLEN The receive maximum length register RXMAXLEN is shown in Figure 66 and described in Table 60 Figure 66 Receive Maximum Length Register RXMAXLEN 31 16 Reserved R 0 15 0 RXMAXLEN R W 1518 LEGEND R W Read Write R Read only n value after reset Table 60 Receive Maximum Length Register RXMAXLEN Field Descriptions Bit Field Value Description 31 16 Reserved 0 Reserved 15 0 RXMAXLEN Receive maximum frame length These bits determine the maximum length of a received frame The reset value is 5EEh 1518 Frames with byte counts greater than RXMAXLEN are long frames Long frames with no errors are oversized frames Long frames with CRC code or alignment errors are jabber frames 120 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 25 Receive Buffer Offset Register RXBUFFEROFFSET The receive buffer offset register RXBUFFEROFFSET is shown in Figure 67 and described in Table 61 Figure 67 Receive Buffer Offset Register RXBUFFEROFFSET 31 16 Reserved HO 15 RXBUFFEROFFSET R W 0 LEGEND R W Read Write R Read only n value after reset Table 61 Receive Buffer Offset Register RXBUFFEROFFSET Field Descriptions
67. 6 Receive Alignment Code Errors Register RXALIGNCODEERRORS The total number of frames received on the EMAC that experienced an alignment error or code error Such a frame is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of length 64 to RXMAXLEN bytes inclusive e Had either an alignment error or a code error An alignment error is defined as having all of the following e A frame containing an odd number of nibbles e Fails the frame check sequence test if the final nibble is ignored A code error is defined as a frame that has been discarded because the EMACs MRXER pin is driven with a one for at least one bit time s duration at any point during the frame s reception Overruns have no effect on this statistic CRC alignment or code errors can be calculated by summing receive alignment errors receive code errors and receive CRC errors SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 149 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 50 7 Receive Oversized Frames Register RXOVERSIZED The total number of oversized frames received on the EMAC An oversized frame is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address
68. 7 Receive Pause Timer Register RXPAUSE Field Descriptions csceeeeeeee eee eee eee sees eeeeeeeeaeeeeeeee 139 78 Transmit Pause Timer Register TXPAUSE Field Descriptions ceceeeeeeeeee eee eeeeeeeeeeeeeeeeeeeees 140 79 MAC Address Low Bytes Register MACADDRLO Field Descriptions 20 seeeeeeeeeeeeeeeeeeeeeees 141 80 MAC Address High Bytes Register MACADDRHI Field DescriptionS ssssssssssnnnnnnnnnnnnnnnnnnnnnnnnn 142 81 MAC Index Register MACINDEX Field Descriptions 0ceeceeee eee e ee eee eee eee eee eeeeeeeeeeeeeeeeeeeeneee 143 82 Transmit Channel n DMA Head Descriptor Pointer Register TXnHDP Field Descriptions ccssssseu 144 83 Receive Channel n DMA Head Descriptor Pointer Register RXnNHDP Field Descriptions 0 seeeeee 145 84 Transmit Channel n Completion Pointer Register TXnCP Field Descriptions 146 85 Receive Channel n Completion Pointer Register RXNCP Field Descriptions AN 147 86 Statistics Register Field DescriptionS eee eee eee eee eee eee ene eee e eee n aetna seat nent ea eee ee eeeneeeeees 148 87 EMAC MDIO Revision Hietonm cece eee eee eee eee nena ene e eee e nee n eee enna enna eee na etna eee ene eeaeeeeneee 159 SPRUEF8F March 2006 Revised November 2010 List of Tables 9 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated IA TEXAS INSTRUMENTS Preface SPRUEF8F March 2006 Revised November 2010 Read This First Ab
69. 7 pending interrupt mask Write 1 to enable interrupt 6 RX6PENDMASK 0 Receive channel 6 pending interrupt mask Write 1 to enable interrupt 5 RX5PENDMASK 0 Receive channel 5 pending interrupt mask Write 1 to enable interrupt 4 RX4PENDMASK 0 Receive channel 4 pending interrupt mask Write 1 to enable interrupt 3 RX3PENDMASK 0 Receive channel 3 pending interrupt mask Write 1 to enable interrupt 2 RX2PENDMASK 0 Receive channel 2 pending interrupt mask Write 1 to enable interrupt 1 RX1PENDMASK 0 Receive channel 1 pending interrupt mask Write 1 to enable interrupt 0 RXOPENDMASK 0 Receive channel 0 pending interrupt mask Write 1 to enable interrupt SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO Copyright 2006 2010 Texas Instruments Incorporated 109 EMAC Port Registers 5 16 Receive Interrupt Mask Clear Register RXINTMASKCLEAR The receive interrupt mask clear register RXINTMASKCLEAR is shown in Figure 58 and described in l TEXAS INSTRUMENTS www ti com Table 52 Figure 58 Receive Interrupt Mask Clear Register RXINTMASKCLEAR 31 24 Reserved R 0 23 22 21 20 19 18 17 16 RX7PULSE RX6PULSE RX5PULSE RX4PULSE RX3PULSE RX2PULSE RX1PULSE RXOPULSE MASK MASK MASK MASK MASK MASK MASK MASK 15 Reserved R 0 7 6 5 4 3 2 1 0 RX7PEND RX6PEND RX5PEND RX4PEND RX3PEND RX2PEND RX1PEND RXOPEND MASK MASK MASK MAS
70. 86 C6472 device There are some trade offs in terms of cache performance and throughput when the descriptors are put in L2 versus when they are put in EMAC internal memory The cache performance improves when the buffer descriptors are put in the internal memory However the EMAC throughput is better when the descriptors are put in the local EMAC RAM C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 2 3 System Level Connections On the TCI6486 C6472 device EMACO and EMAC1 support the following different types of interfaces to EMAC Functional Architecture physical layer devices PHYs or switches Each EMAC can be configured to only one interface at any given time EMACO interface is selected by programming MACSELO 2 0 pins see Table 4 and EMAC1 interface is selected by programming MACSEL1 1 0 pins see Table 5 Table 4 EMACO Interface Selection Pins MACSELO 2 0 Interface 000 MII 001 RMII 010 GMII 011 RGMII 100 Not used 101 S3MII 110 Not used 111 Not used Table 5 EMAC1 Interface Selection Pins MACSEL1 1 0 Interface 00 Not used 01 S3MIl 10 RGMII 11 RMII Table 6 explains the decoding of MACSELO 2 0 MACSEL1 1 0 and EMAC1_EN of the DEVCTL register Table 6 MACSELO 2 0 MACSEL1 1
71. AS INSTRUMENTS www ti com EMAC Functional Architecture e Initialize the TXnHDP registers to zero e Enable the desired transmit interrupts using the TXINTMASKSET and TXINTMASKCLEAR registers e Set the appropriate configuration bits in the MACCONTROL register e Set up the transmit channel s buffer descriptors in host memory e Enable the transmit DMA controller by setting the TXEN bit in the TXCONTROL register e Write the appropriate TXnHDP registers with the pointer to the first descriptor to start transmit operations 2 12 2 Transmit Channel Teardown 2 13 2 14 The host commands a transmit channel teardown by writing the channel number to the TXTEARDOWN register When a teardown command is issued to an enabled transmit channel the following occurs e Any frame currently in transmission completes normally e The TDOWNCMPLT flag is set in the next SOP buffer descriptor in the chain if there is one e The channel head descriptor pointer is cleared e A transmit interrupt is issued informing the host of the channel teardown e The corresponding TXnCP register contains the value FFFF FFFCh e The host should acknowledge a teardown interrupt with an FFFF FFFCh acknowledge value Channel teardown may be commanded on any channel at any time The host is informed of the teardown completion by the set teardown complete buffer descriptor bit TDOWNCMPLT The EMAC does not clear any channel enables due to a teardown command A tea
72. Contents 3 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS www ti com 4 11 MDIO User Command Complete Interrupt Mask Clear Register USERINTMASKCLEAR seeeeee 86 4 12 MDIO User Access Register 0 USERACCESSO ccceeeeeeeee ee ee nese ee eee ee eeeee tease eee eeeeeeeneeeeeeeee 87 4 13 MDIO User PHY Select Register 0 USERPHYSELO cecceeeeeeeee ee ee eee eee sees eeeeeeeeeeeeeeeeeeeeenees 88 4 14 MDIO User Access Register 1 USERACCESS1 ceeceeeeeeeeee eect ence ee eee ee eeeee sees eneeeeeeeeeneeeeeneee 89 4 15 MDIO User PHY Select Register 1 USERPHYSEL1 1 0 ceceeeeeeeeee ence eee eee eee eeeeeeeeeeeeeeeeeeeeenees 90 5 EMAC Port R gisSt rS asermar pe a E a aaa ENa Eaa 91 5 1 Transmit Identification and Version Register TXIDVER a 95 5 2 Transmit Control Register TXCONTROL gege suiieceaneiciieiaate Eea EEE 96 5 3 Transmit Teardown Register TXTEARDOWN 97 5 4 Receive Identification and Version Register RXIDVER an 98 5 5 Receive Control Register RXCONTROL AN 99 5 6 Receive Teardown Register RXTEARDOWN cceeceeece cette eect eee ee seen eee seen eeeeeeeeeenaeeeeeeeeeaees 100 5 7 Transmit Interrupt Status Unmasked Register TXINTSTATRAW cceeceeeeeee eee eeeeeeeeeeeeeeeeeees 101 5 8 Transmit Interrupt Status Masked Register TXINTSTATMASKED cceeeeeeeee tees eee eeeeeeeeeeee 102 5 9 Transmit Interrupt Mask Set Register
73. DIO module uses the USERACCESSn register to access the PHY control registers Software functions that implement the access process include the following four macros PHYREG_read regadr phyadr Starts the process of reading a PHY register PHYREG_write regadr phyadr data Starts the process of writing a PHY register PHYREG_wait Synchronizes operation makes sure read write is idle PHYREG_wait Results results Waits for read to complete and returns data read It is not necessary to wait after a write operation as long as the status is checked before every operation to make sure the MDIO hardware is idle An alternative approach is to call PHYREG_wait after every write and PHYREG_wait Results after every read then the hardware can be assumed to be idle when starting a new operation 50 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture The implementation of these macros using the register layer Chip Support Library CSL is shown in Example 3 USERACCESSO is assumed Note that this implementation does not check the ACK bit on PHY register reads in other words it does not follow the procedure outlined in Section 2 8 2 3 As the ALIVE register initially selects a PHY it is assumed that the PHY is acknowledging read operations It is possible that a PHY could bec
74. Descriptions Bit Field Value Description 31 24 MACADDR2 MAC source address bits 23 16 byte 2 23 16 MACADDR3 MAC source address bits 31 24 byte 3 15 8 MACADDR4 MAC source address bits 39 32 byte 4 7 0 MACADDR5 MAC source address bits 47 40 byte 5 142 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 45 MAC Index Register MACINDEX The MAC index register MACINDEX is shown in Figure 87 and described in Table 81 Figure 87 MAC Index Register MACINDEX 31 16 Reserved HO 15 5 4 0 Reserved MACINDEX R 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 81 MAC Index Register MACINDEX Field Descriptions Bit Field Value Description 31 5 Reserved 0 Reserved 4 0 MACINDEX MAC address index The host must write the index into the RX ADDR RAM in the MACINDEX field followed by the upper 32 bits of address followed by the lower 16 bits of address with control bits The 53 bit indexed ram location is written when the low location is written All 32 address RAM locations must be initialized prior to enabling packet reception SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 143 Cop
75. Descriptor Format SEENEN REENEN ENEE ne neenaeeneneneneeeseneesaneeasereneneneneesanenasenenes of 14 EMIC Block Dark ege EES ee EERSTEN SE 41 15 Pacing Ee e 42 16 TDSM State Transition DiaQtaMsicccscccececseccdeedeceesdsscsdecedanes rede SEKR ERAN ge E Se R NEEN See 43 17 DSM State Transition Diagramm esgebugeu dee SN SEN EENS IERENS SEENEN a Eege A4 18 Transmit Pacer and Interrupt Combiner EE 45 19 Receive Pacer and Interrupt CGombiner EEN 46 20 Gommon Turi ele E EE 47 21 MBI Module BIOCK Diagrams steet eege 48 22 EMAG Module Block DiaQraim snc c cceccsccn cence cecnencnscnnnnwienennec a a SEENEN ENER REENEN KSE NER 52 23 EW INT OTL ET 71 24 RPCFG REISTER eise ele ce od EEE wale wad coatiaaed dead a EE EEE EE EAN 72 25 RPSTAT REGISTON orire TEIE E TEE EEE EE 73 26 BR le Re EE 74 27 MPSTAT EE 75 28 Prescalar Configuration Register PDGCEO eee eee eee e eee eee ee sees nee e eae eaeeeeeneeeeeenaeeeeeeeenaees 75 29 MDIO Version Register VERSION EEN ENNEN 77 30 MDIO Control Register CONTPROL ENEE ENEE 78 31 PHY Acknowledge Status Register ALIVE ENEE EEN 79 32 PHY Link Status Heoleter ENRk 2 gege EES SEENEN EES EEN 80 33 MDIO Link Status Change Interrupt Unmasked Register LINKINTRAW cceeeeeeeeeeeeeeeeeeeeeeeeeees 81 34 MDIO Link Status Change Interrupt Masked Register LINKINTMASKED nnuuassssssssssnnsnnnnnnnnrnnnnnnnnns 82 35 MDIO User Command Complete Interrupt Unmasked Register USERINTRAW eeeeeee
76. E 0x01000000u define EMAC_DSC_FLAG_ FRAGMENT 0x00800000u define EMAC_DSC_FLAG_UNDERSIZED 0x00400000u define EMAC_DSC_FLAG_CONTROL 0x00200000u define EMAC_DSC_FLAG_ OVERRUN 0x00100000u define EMAC_DSC_FLAG_CODEERROR 0x00080000u define EMAC_DSC_FLAG_ALIGNERROR 0x00040000u define EMAC_DSC_FLAG_CRCERROR 0x00020000u define EMAC_DSC_FLAG NOMATCH 0x00010000u SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 37 Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 5 5 1 Next Descriptor Pointer The next descriptor pointer indicates the 32 bit word aligned memory address of the next buffer descriptor in the receive queue The pointer creates a linked list of buffer descriptors If the value of the pointer is zero then the current buffer is the last buffer in the queue The software application must set this value prior to adding the descriptor to the active receive list This pointer is not altered by the EMAC The value of pNext should never be altered once the descriptor is in an active receive queue unless its current value is NULL If the pNext pointer is initially NULL and more empty buffers can be added to the pool the software application may alter this pointer to indicate a newly appended descriptor The EMAC will use the new pointer value and proceed to the next descriptor unless the pNext val
77. EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 5 5 7 End of Packet EOP Flag When set this flag indicates that the descriptor points to the last packet buffer for a given packet For a single fragment packet both the start of packet SOP and EOP flags are set Otherwise the descriptor pointing to the last packet buffer for the packet has the EOP flag set The software application initially clears this flag before adding the descriptor to the receive queue The EMAC sets this bit on EOP descriptors 2 5 5 8 Ownership OWNER Flag When set this flag indicates that the descriptor is currently owned by the EMAC The software application sets this flag before adding the descriptor to the receive descriptor queue The EMAC clears this flag once it is finished with a given set of descriptors associated with a received packet The EMAC updates the flag on SOP descriptor only If the application identifies that the OWNER flag is cleared on an SOP descriptor it may assume that the EMAC has released all descriptors up to and including the first with the EOP flag set Note that for single buffer packets the same descriptor will have both the SOP and EOP flags set 2 5 5 9 End of Queue EOQ Flag When set this flag indicates that the specified descriptor was the last descriptor in the rec
78. EMAC peripheral 2 9 2 EMAC Module Operational Overview After reset initialization and configuration of the EMAC the application software running on the host may initiate transmit operations Transmit operations are initiated by host writes to the appropriate transmit channel head descriptor pointer contained in the state RAM block The transmit DMA controller then fetches the first packet in the packet chain from memory The DMA controller writes the packet into the transmit FIFO in bursts of 64 byte cells The MAC transmitter initiates the packet transmission when either the threshold number of cells configurable via TXCELLTHRESH in the FIFOCONTROL register have been written to the transmit FIFO or a complete packet has been written whichever is smaller The SYNC block transmits the packet over one of the MII interfaces in accordance with the 802 3 protocol The statistics block counts transmit statistics Receive operations are initiated by host writes to the appropriate receive channel head descriptor pointer after host initialization and configuration The SYNC sub module receives packets and strips off the Ethernet related protocol The packet data is input to the MAC receiver which checks for address match in conjunction with the receive address block and processes errors Accepted packets are written to the receive FIFO in bursts of 64 byte cells The receive DMA controller then writes the packet data to memory The statistics block cou
79. EMAC1 If the device is interfaced to an Ethernet switch through the RMII interface all device RMII reference clocks should be externally sourced from the same zero delay clock buffer 2 3 3 Gigabit Media Independent Interface GMIl Connections Figure 4 shows a device with integrated EMAC and MDIO interfaced to the PHY via a GMII connection This interface is available in 10 Mbps 100 Mbps and 1000 Mbps modes Figure 4 Ethernet Configuration with GMIl Interface MTCLK GMTCLK MTXD 7 0 2 5 MHZ 25 MHz MTXEN or 125 MHz MCOL MCRS Physical device Transformer MRXD 7 0 PHY The GMII interface supports 10 100 1000 Mbps modes Only full duplex mode is available in 1000 Mbps mode In 10 100 Mbps modes the GMII interface acts like an MII interface and only the lower 4 bits of data are transferred for each of the data buses Table 9 summarizes the individual EMAC and MDIO signals for the GMII interface SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 21 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture A TEXAS INSTRUMENTS www ti com Table 9 EMAC and MDIO Signals for GMII Interface Signal Name UO Description MTCLK GMTCLK MTXD 7 0 MTXEN MCOL MCRS MRCLK MRXD 7 0 MRXDV MRXER MDCLK MDIO UO Transmit clock MTCLK The transmit clock is a continuous clock that pr
80. END EMAC module host error interrupt HOSTPEND pending status bit 16 STATPEND EMAC module statistics interrupt STATPEND pending status bit 15 8 RXPEND Receive channels 0 7 interrupt RXNPEND pending status bit Bit 8 is receive channel 0 7 0 TXPEND Transmit channels 0 7 interrupt TXnPEND pending status bit Bit 0 is transmit channel 0 SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 105 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 12 MAC End of Interrupt Vector Register MACEOIVECTOR The MAC end of interrupt vector register MACEOIVECTOR is shown in Figure 54 and described in Table 48 Figure 54 MAC End of Interrupt Vector Register MACEOIVECTOR 31 5 4 0 Reserved MAC EOL VECTOR R 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 48 MAC End of Interrupt Vector Register MACEOIVECTOR Field Descriptions Bit Field Value Description 31 5 Reserved 0 Reserved 4 MAC_EOI VECTOR MAC end of interrupt vector The EOI_VECTOR 4 0 pins reflect the value written to this location one peripheral bus clock cycle after a write to this location The EOI_WR signal is asserted for a single clock cycle after a latency of two peripheral bus clock cycles when a write is performed to this location 106 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revis
81. ENTS www ti com EMAC Functional Architecture 2 5 4 1 Next Descriptor Pointer The next descriptor pointer indicates the 32 bit word aligned memory address of the next buffer descriptor in the transmit queue The pointer creates a linked list of buffer descriptors If the value of this pointer is zero then the current buffer is the last buffer in the queue The software application must set this value prior to adding the descriptor to the active transmit list The pointer is not altered by the EMAC The value of pNext should never be altered once the descriptor is in an active transmit queue unless its current value is NULL If the pNext pointer is initially NULL and more packets need to be queued for transmit the software application may alter this pointer to point to a newly appended descriptor The EMAC will use the new pointer value and proceed to the next descriptor unless the pNext value has already been read If the pNext value has already been read the transmitter will halt on the specified transmit channel and the software application may restart it then The software can detect this issue by searching for an end of queue EOQ condition flag on the updated packet descriptor when it is returned by the EMAC 2 5 4 2 Buffer Pointer The buffer pointer is the byte aligned memory address of the memory buffer associated with the buffer descriptor The software application must set this value prior to adding the descriptor to the active tr
82. Flag This flag is used when a transmit queue is being torn down or aborted instead of allowing transmission such as during device driver reset or shutdown conditions The EMAC sets this bit in the SOP descriptor of each packet as it is aborted from transmission Note that this flag is valid on SOP descriptors only Also note that only the first packet in an unsent list has the TDOWNCMPLT flag set The EMAC does not process subsequent descriptors 2 5 4 11 Pass CRC PASSCRC Flag The software application sets this flag in the SOP packet descriptor before it adds the descriptor to the transmit queue Setting this bit indicates to the EMAC that the 4 byte Ethernet CRC is already present in the packet data and that the EMAC should not generate its own version of the CRC When the CRC flag is cleared the EMAC generates and appends the 4 byte CRC The buffer length and packet length fields do not include the CRC bytes When the CRC flag is set the 4 byte CRC is supplied by the software application and is appended to the end of the packet data The buffer length and packet length fields include the CRC bytes as they are part of the valid packet data Note that this flag is valid on SOP descriptors only 36 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS
83. GMDIO UO Receive control RGRXCTL The receive control data has the receive data valid MRXDV signal on the rising edge of the receive clock and a derivative of receive data valid and receive error MRXER on the falling edge of RGRXC When receiving a valid frame with no errors MRXDV TRUE is generated as a logic high on the rising edge on RGRXC and MRXER FALSE is generated as a logic high on the falling edge of RGRXC When no frame is being received MRXDV FALSE is generated as a logic low on the rising edge of RGRXC and MRXER FALSE is generated as a logic low on the falling edge of RGRXC When receiving a valid frame with errors MRXDV TRUE is generated as a logic high on the rising edge of RGRXC and MRXER TRUE is generated as a logic low on the falling edge of RGRXC Management data clock RGMDCLK The RGMDIO data clock is sourced by the MDIO module It synchronizes MDIO data access operations done on the RGMDIO pin The frequency of this clock is controlled by the CLKDIV bits in the MDIO control register CONTROL Management data input output RGMDIO The RGMDIO pin drives PHY management data into and out of the PHY by way of an access frame consisting of start of frame read write indication PHY address register address and data bit cycles The RGMDIO pin acts as an output for everything except the data bit cycles when the pin acts as an input for read operations RGMII pins are not multiplexed with other interfaces
84. HY register to be accessed for this transaction 20 16 PHYADR PHY address bits This field specifies the PHY to be accessed for this transaction 15 0 DATA User data bits These bits specify the data value read from or to be written to the specified PHY register SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 87 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS MDIO Registers www ti com 4 13 MDIO User PHY Select Register 0 VSERPHYSELO The MDIO user PHY select register 0 USERPHYSELO is shown in Figure 40 and described in Table 33 Figure 40 MDIO User PHY Select Register 0 USERPHYSELO 31 16 Reserved HO 15 8 7 6 5 4 0 Reserved LINKSEL LINKINTENB Reserved PHYADRMON R 0 R W 0 R W 0 HO R W 0 LEGEND R Read only R W Read Write n value after reset Table 33 MDIO User PHY Select Register 0 USERPHYSELO Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 LINKSEL Link status determination select bit Default value is 0 which implies that the link status is determined by the MDIO state machine This is the only option supported on this device 6 LINKINTENB Link change interrupt enable Set to 1 to enable link change status interrupts for PHY address specified in PHYADRMON Link change interrupts are disabled if this bit is set to 0 0 Link change
85. K MASK MASK MASK MASK LEGEND R Read only R W Read Write R WC Read Write 1 to clear n value after reset Table 52 Receive Interrupt Mask Clear Register RXINTMASKCLEAR Field Descriptions Bit Field Value Description 31 24 Reserved 0 Reserved read as 0 23 RX7PULSEMASK 0 Receive channel 7 pulse interrupt mask Write 1 to disable interrupt 22 RX6PULSEMASK 0 Receive channel 6 pulse interrupt mask Write 1 to disable interrupt 21 RX5PULSEMASK 0 Receive channel 5 pulse interrupt mask Write 1 to disable interrupt 20 RX4PULSEMASK 0 Receive channel 4 pulse interrupt mask Write 1 to disable interrupt 19 RX3PULSEMASK 0 Receive channel 3 pulse interrupt mask Write 1 to disable interrupt 18 RX2PULSEMASK 0 Receive channel 2 pulse interrupt mask Write 1 to disable interrupt 17 RX1PULSEMASK 0 Receive channel 1 pulse interrupt mask Write 1 to disable interrupt 16 RXOPULSEMASK 0 Receive channel 0 pulse interrupt mask Write 1 to disable interrupt 15 8 Reserved 0 Reserved read as 0 7 RX7PENDMASK 0 Receive channel 7 pending interrupt mask Write 1 to disable interrupt 6 RX6PENDMASK 0 Receive channel 6 pending interrupt mask Write 1 to disable interrupt 5 RX5PENDMASK 0 Receive channel 5 pending interrupt mask Write 1 to disable interrupt 4 RX4PENDMASK 0 Receive channel 4 pending interrupt mask Write 1 to disable interrupt 3 RX3PENDMASK 0 Rec
86. K Timed EVT_TIMED delay SM EVT_IN EVT_OUT DIV_NEXT Divide SM C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 7 2 Timed Delay State Machine TDSM The timed delay state machine fully implements the functionality of the time delay based interrupt pacing The TIME_CFG bit field of the TPCFG and RPCFG registers described in Section 3 is set to 0 on reset and disables this state machine When the TIME_CFG is set to a non zero value an output pulse is generated after the TIME_CFG number of prescalar output periods The counter starts counting on the first event The state machine has three states WAITING DELAY and OUTPUT Upon reset the state machine is placed in the WAITING state The state machine makes transitions between the states as shown in Figure 16 Note that states that are grayed out are transitional states in the sense that the SM does not stay in the grayed state While in the transitional state it typically does an operation like incrementing the TIME or resetting the TIME It then changes the state to the state illustrated by the dotted line Figure 16 TDSM State Transition Diagram EVT_PULSE 0 or EVT_PULSE 1 amp amp TIME gt TIME_CFG 1 amp amp _ TIME lt TIME_CFG EVT_PULSE PS_TICK 0 amp amp DI
87. LIGNERROR Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet contained an alignment error and was not discarded because the RXCEFEN bit was set in the RXMBPENABLE register 2 5 5 20 CRC Error CRCERROR Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet contained a CRC error and was not discarded because the RXCEFEN bit was set in the RXMBPENABLE register 2 5 5 21 No Match NOMATCH Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet did not pass any of the EMAC s address match criteria and was not discarded because the RXCAFEN bit was set in the RXMBPENABLE register Although the packet is a valid Ethernet data packet it is only received because the EMAC is in promiscuous mode 2 6 Communications Port Programming Interface CPPI The CPPI refers to the data structures used by the EMAC to describe transmit and receive packets and the application programming interface to manipulate the data structures The CPPI maximizes the efficiency of communication between host processor and EMAC It minimizes the host interaction maximizes the memory use efficiency and maximizes the symmetry between transmit and receive operations Some of the important features of the CPPI include distributed buffer management protocol independent packet level interface support for multichannel multi priority queuing and support for multiple buffer queues The details of transm
88. MDIO 15 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 1 3 2 2 16 GMIl Clocking The GMII interface is available only on EMACO and requires two clock sources generated internally the peripheral bus clock and the RFTCLK inputs to the EMAC module SYSCLK14 is programmed to 4 for this interface to provide a 125 MHz clock to the RFTCLK input of EMAC The GMIl interface is selected by programming MACSELO to 2 010b Transmit and receive clock sources for 10 100 Mbps modes are provided from an external PHY via the MTCLK and MRCLK pins For 1000 Mbps mode the receive clock is provided by an external PHY via the MRCLK pin For transmit in 1000 Mbps mode the clock is sourced synchronous with the data and is provided by the EMAC to be output on the GMTCLK pin For timing purposes data in 10 100 Mbps mode is transmitted and received with reference to MTCLK and MRCLK respectively For 1000 Mbps mode receive timing is the same but transmit is relative to GMTCLK RGMII Clocking The RGMII interface is selected by programming MACSELO to 3 011b and MACSEL1 to 2 10b RGMII requires 4 internally generated clocks peripheral bus clock and three reference clocks The EMAC drives the transmit clock while an external PHY generates the receive clock The reference clock drives the device pin that gives the 125 MHz clock to the PHY
89. N register to the maximum frame length you want to be received 11 Set up the RXMBPENABLE register with an initial configuration The configuration is based on the current receive filter settings of the device driver Some drivers may enable things like broadcast and multicast packets immediately while others may not 12 Set the appropriate configuration bits in the MACCONTROL register do not set the GMIIEN bit yet 13 Clear all unused channel interrupt bits by writing RXINTMASKCLEAR and TXINTMASKCLEAR 14 Enable the receive and transmit channel interrupt bits in RXINTMASKSET and TXINTMASKSET for the channels to be used and enable the HOSTMASK and STATMASK bits using the MACINTMASKSET register 15 Initialize the receive and transmit descriptor list queues using the 8K descriptor memory block contained in the CPPI buffer manager 16 Prepare to receive by writing a pointer to the head of the receive buffer descriptor list to RXnNHDP 17 Enable the receive and transmit DMA controllers by setting the RXEN bit in the RXCONTROL register and the TXEN bit in the TXCONTROL register Then set the GMIIEN bit in MACCONTROL 18 If the gigabit mode is desired available only if using GMI or RGMII interface set the GIG bit in the MACCONTROL register 19 When using RMIl release the interface logic from reset by clearing the RMII_RST field of the EMAC A C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation
90. PPI buffer manager This DMA engine is totally independent of the TCI6486 C6472 DSP EDMA Transmit FIFO The transmit FIFO consists of 24 cells of 64 bytes each and the associated control logic This enables a packet of 1518 bytes standard Ethernet packet size to be sent without the possibility of under run The FIFO buffers data in preparation for transmission MAC transmitter The MAC transmitter formats frame data from the transmit FIFO and transmits the data using the CSMA CD access protocol The frame CRC can be automatically appended if required The MAC transmitter also detects transmission errors and passes statistics to the statistics registers e Statistics logic The statistics logic RAM counts and stores the Ethernet statistics keeping track of 36 different Ethernet packet statistics e State RAM The state RAM contains the head descriptor pointers and completion pointers registers for both transmit and receive channels e Interrupt controller The interrupt controller contains the interrupt related registers and logic The 18 raw EMAC interrupts are input to this sub module and masked module interrupts are output e Control registers and logic The EMAC is controlled by a set of memory mapped registers The control logic also signals transmit receive and status related interrupts to the CPU through the EMIC module e Clock and reset logic The clock and reset sub module generates all the clocks and resets for the
91. PULSE TX2PULSE TX1PULSE TXOPULSE MASK MASK MASK MASK MASK MASK MASK MASK 15 S Reserved R 0 7 6 5 4 3 2 1 0 TX7PEND TX6PEND TX5PEND TX4PEND TX3PEND TX2PEND TX1PEND TXOPEND MASK MASK MASK MASK MASK MASK MASK MASK LEGEND R W Read Write R Read only n value after reset Table 46 Transmit Interrupt Mask Clear Register TXINTMASKCLEAR Field Descriptions Bit Field Value Description 31 24 Reserved 0 Reserved read as 0 23 TX7PULSEMASK 0 Transmit channel 7 pulse interrupt mask Write 1 to disable interrupt 22 TX6PULSEMASK 0 Transmit channel 6 pulse interrupt mask Write 1 to disable interrupt 21 TX5PULSEMASK 0 Transmit channel 5 pulse interrupt mask Write 1 to disable interrupt 20 TX4PULSEMASK 0 Transmit channel 4 pulse interrupt mask Write 1 to disable interrupt 19 TX3PULSEMASK 0 Transmit channel 3 pulse interrupt mask Write 1 to disable interrupt 18 TX2PULSEMASK 0 Transmit channel 2 pulse interrupt mask Write 1 to disable interrupt 17 TX1PULSEMASK 0 Transmit channel 1 pulse interrupt mask Write 1 to disable interrupt 16 TXOPULSEMASK 0 Transmit channel 0 pulse interrupt mask Write 1 to disable interrupt 15 8 Reserved 0 Reserved read as 0 7 TX7PENDMASK 0 Transmit channel 7 pending interrupt mask Write 1 to disable interrupt 6 TX6PENDMASK 0 Transmit channel 6 pending interrupt mask Write 1 to disable interrupt 5 TX5PENDMASK 0 Transmi
92. R MDIO User Command Complete Interrupt Mask Clear Section 4 11 Register 80h USERACCESSO MDIO User Access Register 0 Section 4 12 84h USERPHYSELO MDIO User PHY Select Register 0 Section 4 13 88h USERACCESS1 MDIO User Access Register 1 Section 4 14 8Ch USERPHYSEL1 MDIO User PHY Select Register 1 Section 4 15 76 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 2 MDIO Version Register VERSION The MDIO version register VERSION is shown in Figure 29 and described in Table 22 Figure 29 MDIO Version Register VERSION MODID R 7 REVMAJ REVMIN Di R 3 LEGEND R Read only R W Read Write n value after reset Table 22 MDIO Version Register VERSION Field Descriptions Bit Field Value Description 31 16 MODID Identifies the type of peripheral 15 8 REVMAJ Management Interface Module major revision value 7 0 REVMIN Management Interface Module minor revision value SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 77 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS MDIO Registers www ti com 4 3 MDIO Control Register CONTROL The MDIO control register CONTROL is shown
93. RXnFREEBUFFER The receive channel 0 7 free buffer count register RXnFREEBUFFER is shown in Figure 70 and described in Table 64 Figure 70 Receive Channel n Free Buffer Count Register RXnFREEBUFFER 31 16 Reserved HO 15 0 RXnFREEBUF WI 0 tLEGEND R Read only R W Read Write WI Write to increment n value after reset Table 64 Receive Channel n Free Buffer Count Register RXNFREEBUFFER Field Descriptions Bit Field Value Description 31 16 Reserved 0 Reserved 15 0 RXnFREEBUF Receive free buffer count These bits contain the count of free buffers available The RXFILTERTHRESH value is compared with this field to determine if low priority frames should be filtered The RXnFLOWTHRESH value is compared with this field to determine if receive flow control should be issued against incoming packets if enabled This is a write to increment field This field rolls over to zero on overflow If hardware flow control or QOS is used the host must initialize this field to the number of available buffers one register per channel The EMAC decrements by the number of buffers in the received frame the associated channel register for each received frame The host must write this field with the number of buffers that have been freed due to host processing SPRUEF8F March 2006 Revised November 2010 124 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 20
94. Register MACINTMASKSET Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 HOSTMASK Host error interrupt mask set bit Write 1 to enable interrupt a write of O has no effect 0 STATMASK Statistics interrupt mask set bit Write 1 to enable interrupt a write of 0 has no effect SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated C6472 TCI6486 EMAC MDIO 113 I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 20 MAC Interrupt Mask Clear Register MACINTMASKCLEAR The MAC interrupt mask clear register MACINTMASKCLEAR is shown in Figure 62 and described in Table 56 Figure 62 MAC Interrupt Mask Clear Register MACINTMASKCLEAR 31 16 Reserved R 0 15 2 1 0 HOST STAT Reserved MASK MASK HO R WC 0 R WC 0 LEGEND R Read only R W Read Write R WC Read Write 1 to clear n value after reset Table 56 MAC Interrupt Mask Clear Register MACINTMASKCLEAR Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 HOSTMASK Host error interrupt mask clear bit Write 1 to disable interrupt a write of 0 has no effect 0 STATMASK Statistics interrupt mask clear bit Write 1 to disable interrupt a write of 0 has no effect 114 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feed
95. Register Section 5 46 610h TX4HDP Transmit Channel 4 DMA Head Descriptor Pointer Register Section 5 46 614h TX5HDP Transmit Channel 5 DMA Head Descriptor Pointer Register Section 5 46 618h TX6HDP Transmit Channel 6 DMA Head Descriptor Pointer Register Section 5 46 61Ch TX7HDP Transmit Channel 7 DMA Head Descriptor Pointer Register Section 5 46 620h RXOHDP Receive Channel 0 DMA Head Descriptor Pointer Register Section 5 47 624h RX1HDP Receive Channel 1 DMA Head Descriptor Pointer Register Section 5 47 628h RX2HDP Receive Channel 2 DMA Head Descriptor Pointer Register Section 5 47 62Ch RX3HDP Receive Channel 3 DMA Head Descriptor Pointer Register Section 5 47 630h RX4HDP Receive Channel 4 DMA Head Descriptor Pointer Register Section 5 47 634h RX5HDP Receive Channel 5 DMA Head Descriptor Pointer Register Section 5 47 638h RX6HDP Receive Channel 6 DMA Head Descriptor Pointer Register Section 5 47 63Ch RX7HDP Receive Channel 7 DMA Head Descriptor Pointer Register Section 5 47 640h TXOCP Transmit Channel 0 Completion Pointer Interrupt Section 5 48 Acknowledge Register 644h TX1CP Transmit Channel 1 Completion Pointer Interrupt Section 5 48 Acknowledge Register 648h TX2CP Transmit Channel 2 Completion Pointer Interrupt Section 5 48 Acknowledge Register 64Ch TX3CP Transmit Channel 3 Completion Pointer Interrupt Section 5 48 Acknowledge Register 650h TX4CP Transmit Channel 4 Completion Pointer Interrupt Section 5 48 Acknowledge Register 654h TX5CP Trans
96. Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 35 MAC Source Address Low Bytes Register MACSRCADDRLO The MAC source address low bytes register MACSRCADDRLO is shown in Figure 77 and described in Table 71 Figure 77 MAC Source Address Low Bytes Register MACSRCADDRLO 31 16 Reserved R 0 15 8 7 0 MACSRCADDRO MACSRCADDR1 R W 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 71 MAC Source Address Low Bytes Register MACSRCADDRLO Field Descriptions Bit Field Value Description 31 16 Reserved 0 Reserved 15 8 MACSRCADDRO MAC source address lower 8 bits byte 0 7 0 MACSRCADDRI1 MAC source address bits 15 8 byte 1 SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 133 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 36 MAC Source Address High Bytes Register MACSRCADDRHI The MAC source address high bytes register MACSRCADDRHI is shown in Figure 78 and described in Table 72 Figure 78 MAC Source Address High Bytes Register MACSRCADDRHI 31 24 23 16 MACSRCADDR2 MACSRCADDR3 R W 0 R W 0 15 8 7 0 MACSRCADDR4 MACSRCADDR5 R W 0 R W 0 LEGEND R W Read Write R Read only n value afte
97. Revised November 2010 C6472 TCI6486 EMAC MDIO 101 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 8 Transmit Interrupt Status Masked Register TXINTSTATMASKED The transmit interrupt status masked register TXINTSTATMASKED is shown in Figure 50 and described in Table 44 Figure 50 Transmit Interrupt Status Masked Register TXINTSTATMASKED 31 16 Reserved HO 15 8 7 6 5 4 3 2 1 0 Biesanied TX7 TX6 TX5 TX4 TX3 TX2 TX1 TXO PEND PEND PEND PEND PEND PEND PEND PEND HO HO HO HO HO HO R 0 R 0 R 0 LEGEND R W R Read only n value after reset Table 44 Transmit Interrupt Status Masked Register TXINTSTATMASKED Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 TX7PEND TX7PEND masked interrupt read 6 TX6PEND TX6PEND masked interrupt read 5 TX5PEND TX5PEND masked interrupt read 4 TX4PEND TX4PEND masked interrupt read 3 TX3PEND TX3PEND masked interrupt read 2 TX2PEND TX2PEND masked interrupt read 1 TX1PEND TX1PEND masked interrupt read 0 TXOPEND TXOPEND masked interrupt read 102 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 5 9 Transmit Interrupt
98. SEN ESA NENNEN ES EES SES EN ENEE ENN SNE NEE 13 3 EMAG Clock eet EE ee 15 4 EMACO Interface Selection PINS ENEE L 5 EMAGC1 Interface Selection PINS ezseeui egugueE eege EEGENEN EENEG SEENEN Nee ed eege L 6 MACSELO 2 0 MACSEL1 1 0 and EMAC1_EN Decoding seceeeeeee cece eee eee tenes eeeeeeeeeeeeeeeeeeees 17 7 EMAC and MDIO Signals for MI Interface 19 8 EMAC and MDIO Signals for RMII Interface 20 9 EMAC and MDIO Signals for GMII Interface EE 22 10 EMAC and MDIO Signals for RGMII Interface AN 23 11 EMAC and MDIO Signals for SSMII Interface 0cceeee eee eee eee eee eee nese eee ee teen eee n eee eeenaeeeeeneenaees 26 12 Ethernet Frame Description 29 13 Basic DOSCIIDIONS ease eege CARE NehE ENEE DE NERT EACK ARENS as 31 14 Receive Frame Treatment SUMMALY c cece eee ee ee ee ee ee eee eee e eee cence teen nese eee n etna etna ee ee eae eeaeeeeeeeeeaees 61 15 Middle of Frame Overrun Treatment EEN 62 16 Emulation COnttol eey2gk gekioege geg EENS RE EE EN SERA can ad ev ed EENS n E aasad 70 17 RPCFG Register Field Descriptions EEN EEN 72 18 RPSTAT Register Field Descriptions rsrsrsrsrs errre sereine a E een 73 19 TPGFG Register Field Descriptions e a a E E E EN 74 20 TPSTAT Register Field D scriptioNS neeaae EEEE a ZS 21 Management Data Input Output MDIO Registers ceeeee eee ee eee eee eee e eee neces eens eeeeneeeaeeeeeeeneaees 76 22 MDIO Version Register VERSION Field Descriptions ccee
99. SERINTRAW is shown in Figure 35 and described in Table 28 Figure 35 MDIO User Command Complete Interrupt Unmasked Register USERINTRAW 31 16 Reserved R 0 15 2 1 0 Reserved USERINTRAW HO R WC 0 LEGEND R Read only R WC Read Write 1 to clear n value after reset Table 28 MDIO User Command Complete Interrupt Unmasked Register USERINTRAW Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 0 USERINTRAW MDIO User command complete event bits When asserted a bit indicates that the previously scheduled PHY read or write command using that particular USERACCESS register has completed Writing a 1 will clear the event and writing 0 has no effect SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 83 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS MDIO Registers www ti com 4 9 MDIO User Command Complete Interrupt Masked Register USERINTMASKED The MDIO user command complete interrupt masked register USERINTMASKED is shown in Figure 36 and described in Table 29 Figure 36 MDIO User Command Complete Interrupt Masked Register USERINTMASKED 31 16 Reserved HO 15 2 1 0 Reserved Hen HO R WC 0 LEGEND R Read only R WC Read Write 1 to clear n value after reset Table 29 MDIO User Command Complete Interrupt Masked Re
100. Section 5 26 120h RXOFLOWTHRESH Receive Channel 0 Flow Control Threshold Register Section 5 27 124h RX1FLOWTHRESH Receive Channel 1 Flow Control Threshold Register Section 5 27 128h RX2FLOWTHRESH Receive Channel 2 Flow Control Threshold Register Section 5 27 12Ch RX3FLOWTHRESH Receive Channel 3 Flow Control Threshold Register Section 5 27 130h RX4FLOWTHRESH Receive Channel 4 Flow Control Threshold Register Section 5 27 134h RX5FLOWTHRESH Receive Channel 5 Flow Control Threshold Register Section 5 27 138h RX6FLOWTHRESH Receive Channel 6 Flow Control Threshold Register Section 5 27 13Ch RX7FLOWTHRESH Receive Channel 7 Flow Control Threshold Register Section 5 27 140h RXOFREEBUFFER Receive Channel 0 Free Buffer Count Register Section 5 28 144h RX1FREEBUFFER Receive Channel 1 Free Buffer Count Register Section 5 28 148h RX2FREEBUFFER Receive Channel 2 Free Buffer Count Register Section 5 28 14Ch RX3FREEBUFFER Receive Channel 3 Free Buffer Count Register Section 5 28 150h RX4FREEBUFFER Receive Channel 4 Free Buffer Count Register Section 5 28 154h RX5FREEBUFFER Receive Channel 5 Free Buffer Count Register Section 5 28 158h RX6FREEBUFFER Receive Channel 6 Free Buffer Count Register Section 5 28 SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 91 Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com Table 36 Ethernet Media Access Controller
101. Signal Processor data manual SPRS612 2 18 Power Management The power saver module integrated in this device allows the clock for different peripherals to be shut down when that peripheral is not being used For more information on the power conservation modes available for the EMAC MDIO peripheral see the TMS320TCI6486 Communications Infrastructure Digital Signal Processor data manual SPRS300 or the 7MS320C6472 Fixed Point Digital Signal Processor data manual SPRS612 2 19 Emulation Considerations EMAC emulation control is implemented for compatibility with other peripherals The SOFT and FREE bits from the EMCONTROL register allow EMAC operation to be suspended SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 69 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Functional Architecture www ti com When the emulation suspend state is entered the EMAC will stop processing receive and transmit frames at the next frame boundary Any frame currently in reception or transmission will be completed normally without suspension For transmission any complete or partial frame in the transmit cell FIFO will be transmitted For receive frames that are detected by the EMAC after the suspend state is entered are ignored No statistics will be kept for ignored frames Table 16 shows how the SOFT and FREE bits affect the operation of the emulation suspend Ta
102. TI eee e eee eeeeeeeeeeeeeeeeeeeeeneeeeeeeee 118 65 Receive Unicast Clear Register HXUNICAGTCLEAR tense eeeee sees eeeeeeeeeeenaeeeeneee 119 66 Receive Maximum Length Register RXMAXLEN ceeeeeeeeeeeee eee eee eee eee e eens tease een eeeeeeenaneeeneee 120 67 Receive Buffer Offset Register RXBUFFEROFFSET cceeceeeeeceeeeeeee eee eeeeeeeeeeeeeneeeeeeeneeneeneee 121 68 Receive Filter Low Priority Frame Threshold Register DHXEIL TERLOWTHDEGH 122 69 Receive Channel n Flow Control Threshold Register RXNFLOWTHRESH ssssssssssssssssnnnnnnnnrrrnnnnnne 123 70 Receive Channel n Free Buffer Count Register RXNFREEBUFFER 0seeeeeeeeeeeeeeeeeeeeeeeeeeeeees 124 71 MAC Control Register MACCONTROL cceeeeec cece eee eee n ee eee eens nesses nese eeeeeeeeeeeeeeeeeeteeeeaeeee 125 72 MAG Status Register MAGSTATUS wasicciicniiceiwcmatniasinetatcemedied E AE a EE a OEA EEES 127 73 Emulation Control Register EMCONT TROL eee eens eee eee eee ease eee eeeeeeeeeeeeeeeeeeaeenaeeeeneee 129 74 FIFO Control Register FIFOCONTROE a gesiegegaeee gege o Seege Ee dE EEN 130 75 MAC Configuration Register MACCONEIO A 131 76 Soft Reset Register SOF HESE suerge deg ee Zeg geleed Neie decd dead deele delt ge See geegeN 132 77 MAC Source Address Low Bytes Register MACSRCADDRLO 0 seceeeeeee eee eeeeee tees eeeeeeeeeeeeeees 133 78 MAC Source Address High Bytes Register MACSRCADDRHI seceeee cece eee ee eens eee eeeeeeeeeeee
103. TMS320C6472 TMS320TCI6486 DSP Ethernet Media Access Controller EMAC Management Data Input Output MDIO Module User s Guide di TEXAS INSTRUMENTS Literature Number SPRUEF8F March 2006 Revised November 2010 SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated IJ TEXAS INSTRUMENTS NL Le 10 1 INTRODUCTION sasecesscntistinds macnn asc E E E 11 1 1 Purpose Of the Peripheral 2 eevegugogeiekNNNgENeK SNE SERNNNN RENE ECKER NENNEN EN ENNEN REENK REENEN AEN 11 1 2 EE HEES ee e ee E E e ee Se 1 3 Functional Block RTE 12 1 4 Industry Standard s Compliance Statement cceeceeee eee eee eee eee eee nese eee ee seen seas teen eeeneeeeeeeeeeeee 14 2 EMAC Functional Architecture 2gus See Ee aaa adi elntin at s ieee EE Deeg 15 2 1 Glock Control saimei a E a a a E 15 2 2 Memory Map NEEN 16 2 3 SYSIEM LeVEl CONMECHONS eg sterz Niege e ege ee ENG bade Edge S EES EE Dee GANSEN 17 2 4 Ethernet too eeneg Eeer 29 2 5 Programming Interface EEN 31 2 6 Communications Port Programming Interface CPPI ceeceeee seen ee eee eee e eee eeeeeee eee eeeeneeeeeeeeeeaees 40 2 7 Ethernet Multicore Interrupt Combiner EMIC Module ceeceeeeeeeeee eee eeeeeeeeeeeeeeeeeeeeenaeeeeeeee 40 2 8 Management Data Input Output MDIO Module 47 2 9 EMAG Module Geet 52 2 10 Media Independent Interfaces AE 54 2 11 Packet RECEIVE Operation emanivecniencnnne
104. TRUMENTS EMAC Port Registers www ti com 5 14 Receive Interrupt Status Masked Register RXINTSTATMASKED The receive interrupt status masked register RXINTSTATMASKED is shown in Figure 56 and described in Table 50 Figure 56 Receive Interrupt Status Masked Register RXINTSTATMASKED 31 16 Reserved HO 15 8 7 6 5 4 3 2 1 0 Reserved RX7 RX6 RX5 RX4 RX3 RX2 SEA RX0 PEND PEND PEND PEND PEND PEND PEND PEND R 0 HO HO R 0 HO HO HO HO HO LEGEND R Read only n value after reset Table 50 Receive Interrupt Status Masked Register RXINTSTATMASKED Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 RX7PEND RX7PEND masked interrupt read 6 RX6PEND RX6PEND masked interrupt read 5 RX5PEND RX5PEND masked interrupt read 4 RX4PEND RX4PEND masked interrupt read 3 RX3PEND RX3PEND masked interrupt read 2 RX2PEND RX2PEND masked interrupt read 1 RX1PEND RX1PEND masked interrupt read 0 RXOPEND RXOPEND masked interrupt read 108 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 5 15 Receive Interrupt Mask Set Register RXINTMASKSET EMAC Port Registers The receive interrupt mask set register RXINTMASKSET is shown in Figure 57 and described in
105. Total number of good broadcast frames received Section 5 50 2 208h RXMCASTFRAMES Total number of good multicast frames received Section 5 50 3 20Ch RXPAUSEFRAMES Pause Receive Frames Register Section 5 50 4 210h RXCRCERRORS Total number of frames received with CRC errors Section 5 50 5 214h RXALIGNCODEERRORS Total number of frames received with alignment code errors Section 5 50 6 218h RXOVERSIZED Total number of oversized frames received Section 5 50 7 21Ch RXJABBER Total number of jabber frames received Section 5 50 8 220h RXUNDERSIZED Total number of undersized frames received Section 5 50 9 224h RXFRAGMENTS Receive Frame Fragments Register Section 5 50 10 228h RXFILTERED Filtered Receive Frames Section 5 50 11 22Ch RXQOSFILTERED Received Frames Filtered by QOS Section 5 50 12 230h RXOCTETS Total number of received bytes in good frames Section 5 50 13 234h TXGOODFRAMES Total number of good frames transmitted Section 5 50 14 238h TXBCASTFRAMES Broadcast Transmit Frames Register Section 5 50 15 23Ch TXMCASTFRAMES Multicast Transmit Frames Register Section 5 50 16 240h TXPAUSEFRAMES Pause Transmit Frames Register Section 5 50 17 244h TXDEFERRED Deferred Transmit Frames Register Section 5 50 18 248h TXCOLLISION Transmit Collision Frames Register Section 5 50 19 24Ch TXSINGLECOLL Transmit Single Collision Frames Register Section 5 50 20 250h TXMULTICOLL Transmit Multiple Collision Frames Register Section 5 50 21 254h TXEXCESSIVECOLL Transmit Excessive Collis
106. Transmit cell depth These bits indicate the number of cells in the transmit FIFO 23 16 RXCELLDEPTH Receive cell depth These bits indicate the number of cells in the receive FIFO 15 8 ADDRESSTYPE Address type 7 0 MACCFIG MAC configuration value SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 131 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 34 Soft Reset Register SOFTRESET The soft reset register SOFTRESET is shown in Figure 76 and described in Table 70 Figure 76 Soft Reset Register GOFTRESET 31 16 Reserved HO 15 1 0 Reserved SOFTRESET HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 70 Soft Reset Register SOFTRESET Field Descriptions Bit Field Value Description 31 1 Reserved 0 Reserved 0 SOFTRESET Software reset Writing a one to this bit causes the EMAC logic to be reset Software reset occurs when the receive and transmit DMA controllers are in an idle state to avoid locking up the Configuration bus After writing a one to this bit it may be polled to determine if the reset has occurred If a one is read the reset has not yet occurred If a zero is read then reset has occurred 0 A software reset has not occurred A software reset has occurred 132 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006
107. V_NEXT 0 TIME 7 Increment 21 amp amp TIO EG AY fg pS E CFO Sa l time l PS_TICK 1 amp amp TIME lt TIME_CFG amp amp DIV_NEXT 0 EVT_PULSE 1 amp amp TIME lt TIME_CFG EVT_PULSE 0 or EVT_PULSE 1 amp amp TIME gt TIME_CFG SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 43 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture 2 7 3 44 A TEXAS INSTRUMENTS www ti com Divide by N State Machine DSM The divide by N state machine fully implements the functionality of the count based interrupt pacing The CNT_CFG bit field of the TPCFG and RPCFG registers described in Section 3 is set to 0 on reset and immediately generates a pulse basically means a zero delay when the TIME_CFG is also set to 0 i e timed delay SM is disabled When the TIME_CFG is set to non zero it then disables the divide by N state machine When the CNT_CFG is set to non zero the CNT_CFG number of events are counted before an output pulse is generated The counter resets and reloads every time when a divide by N pulse is generated The state machine has three states WAITING COUNT and OUTPUT Upon reset the state machine is placed in the WAITING state The state machine makes transitions between the states as shown in Figure 17 Note that states that are grayed out are transitional states in the sense
108. a written by the host buffer descriptor address of the last processed buffer is compared to the data in the register written by the EMAC address of last buffer descriptor used by the EMAC If the two values are not equal indicating that the EMAC has received more packets than the CPU has processed interrupts for the receive packet completion interrupt signal remains asserted If the two values are equal indicating that the host has processed all packets that the EMAC has received the pending interrupt is de asserted Reading the RXnCP register displays the value that the EMAC is expecting The EMAC write to the completion pointer stores the value in the state RAM The CPU written value does not change the register value The host written value is compared to the register content which was written by the EMAC If the two values are equal then the interrupt is removed otherwise the interrupt remains asserted The host may process multiple packets prior to acknowledging an interrupt or the host may acknowledge interrupts for every packet 2 17 1 3 Statistics Interrupt The statistics level interrupt STATPEND is issued when any statistics value is greater than or equal to 8000 0000h if it has been enabled by the STATMASK bit in the MACINTMASKSET register The statistics interrupt is removed by writing to decrement any statistics value greater than 8000 0000h The interrupt remains asserted as long as the most significant bit of any statistics va
109. ad transaction The PHY with the corresponding address has a link and the PHY acknowledges the read transaction 80 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 6 MDIO Link Status Change Interrupt Unmasked Register LINKINTRAW The MDIO link status change interrupt unmasked register LINKINTRAW is shown in Figure 33 and described in Table 26 Figure 33 MDIO Link Status Change Interrupt Unmasked Register LINKINTRAW 31 16 Reserved HO 15 2 1 0 Reserved LINKINTRAW HO R WC 0 LEGEND R Read only R WC Read Write 1 to clear n value after reset Table 26 MDIO Link Status Change Interrupt Unmasked Register LINKINTRAW Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 0 LINKINTRAW MDIO Link change event raw value When asserted a bit indicates that there was an MDIO link change event a change in the LINK register corresponding to the PHY address in the USERPHYSEL register LINKINTRAW 0 and LINKINTRAW 1 correspond to USERPHYSELO and USERPHYSEL1 respectively Writing a 1 will clear the event and writing 0 has no effect SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 81 Submit Documentation Feedback Copyright 2006 2010 Texas Instrument
110. affic The statistics values are cleared to zero 38 clocks after the rising edge of reset When the GMIIEN bit in the MACCONTROL register is set all statistics registers are write to decrement The value written is subtracted from the register value with the result stored in the register If a value greater than the statistics value is written then zero is written to the register writing FFFF FFFFh clears a statistics location When the GMIIEN bit is cleared all statistics registers are read write normal write direct so writing 0000 0000h clears a statistics location All write accesses must be 32 bit accesses The statistics interrupt STATPEND is issued if enabled when any statistics value is greater than or equal to 8000 0000h The statistics interrupt is removed by writing to decrement any statistics value greater than 8000 0000h The statistics are mapped into internal memory space and are 32 bits wide All statistics roll over from FFFF FFFFh to 0000 0000h The network statistics register is shown in Figure 92 and described in Table 86 Figure 92 Statistics Register 31 16 COUNT R W 0 15 0 COUNT R W 0 LEGEND R W Read Write n value after reset Table 86 Statistics Register Field Descriptions Bit Field Value Description 31 0 COUNT Count 5 50 1 Good Receive Frames Register RXGOODFRAMES 5 50 2 148 The total number of good frames received on the EMAC A good frame
111. agram Figure 1 shows the functional block diagram of the EMAC peripherals used in the TCI6486 C6472 device It consists mainly of EMACO EMAC1 CPPI buffer manager per EMAC EMIC per EMAC MDIO A TEXAS INSTRUMENTS www ti com Figure 1 EMAC and MDIO Block Diagram To GEMs EMAC Control 0 Module DMA memory transfer control CPPI buffer manager CPPI RAMO Peripheral CPPI buffer manager CPPI RAM1 memory transfer control EMAC Control 1 Module To GEMs 12 C6472 TCI6486 EMAC MDIO MII0 GMIIO S3MIl0 RMIIO RGMIIO To PHYs S3MII1 RMII1 RGMII1 SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l TEXAS INSTRUMENTS www ti com Introduction The EMAC module provides an efficient interface between the TCI6486 C6472 core processor and the networked community The EMAC supports 10Base T 10 Mbits sec and 100Base TX 100 Mbits sec in either half or full duplex mode and 1000Base T 1000 Mbits sec in full duplex mode with hardware flow control and quality of service QOS support Each EMAC module has a communications port programming interface CPPI buffer manager to manage 8K of CPPI RAM The EMAC uses four 32 bit words as buffer descriptors that point to different buffers in the DSP memory The CPUs create and maintain these buffer descriptors The EMAC reads from and writes to these buffer d
112. and are HSTL I O having voltages different than other interfaces RGMII pins are 1 5 V 1 8 V HSTL I O whereas other interfaces are 3 3 V LVCMOS I O The unused pins of the RGMII PHY should be pulled down to avoid floating inputs C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated JA TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 3 5 Source Synchronous Serial Media Independent Interface S3MIl Connections Figure 6 shows a TCI6486 C6472 device with an integrated EMAC and MDIO interface via S3MII connections connected to a PHY The S3MIl interface supports source synchronous 10 Mbps and 100 Mbps operations with full and half duplex support Figure 6 Ethernet Configuration with S3MIl Interface 125 MHz Kee zero delay clock buffer MHZ_125_CLK TX_CLK TXD TX_SYNC RX CLK Physical layer RXD device RX_SYNC PHY MDCLK MDIO SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 25 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture 26 A TEXAS INSTRUMENTS www ti com Table 11 summarizes the individual EMAC and MDIO signals for the S3MIl interface Table 11 EMAC and MDIO Signals for S3MII Interface Signal Name UO Description TX_CLK O Transmit clock The transmit clock is a co
113. ansmit list This pointer is not altered by the EMAC 2 5 4 3 Buffer Offset This 16 bit field indicates how many unused bytes are at the start of the buffer For example a value of 0000h indicates that no unused bytes are at the start of the buffer and that valid data begins on the first byte of the buffer A value of OOOFh indicates that the first 15 bytes of the buffer are to be ignored by the EMAC and that valid buffer data starts on byte 16 of the buffer The software application must set this value prior to adding the descriptor to the active transmit list This field is not altered by the EMAC Note that this value is only checked on the first descriptor of a given packet where the SOP flag is set It cannot specify the offset of subsequent packet fragments Also as the buffer pointer may point to any byte aligned address this field may be unnecessary depending on the device driver architecture The range of legal values for this field is 0 to Buffer Length 1 2 5 4 4 Buffer Length This 16 bit field indicates how many valid data bytes are in the buffer On single fragment packets this value is also the total length of the packet data to be transmitted If the buffer offset field is used the offset bytes are not counted as part of this length This length counts only valid data bytes The software application must set this value prior to adding the descriptor to the active transmit list This field is not altered by the EMAC 2
114. ansmit and Receive Descriptor Queues The EMAC module processes descriptors in linked list chains Section 2 5 1 The lists controlled by the EMAC are maintained by the application software through the head descriptor pointer HDP registers Since the EMAC supports eight channels for both transmit and receive there are eight head descriptor pointer registers for both They are designated as follows e TXnHDP Transmit Channel o DMA Head Descriptor Pointer Register e RXnHDP Receive Channel n DMA Head Descriptor Pointer Register After an EMAC reset and before enabling the EMAC for send or receive you must initialize all 16 head descriptor pointer registers to zero The EMAC uses a simple system to determine ownership of a descriptor either the EMAC or the application software There is a flag in the descriptor flags field called OWNER When this flag is set the EMAC owns the referenced packet NOTE Ownership is assigned on a packet based granularity not on descriptor granularity Thus only SOP descriptors use the OWNER flag The EMAC patches the SOP descriptor of the corresponding packet and clears the OWNER flag as packets are processed This means that the EMAC is finished processing all descriptors up to and including the first with the EOP flag set This indicates that you have reached the end of the packet This may only be one descriptor with both the SOP and EOP flags set C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Re
115. ata for use by the PHY It is driven synchronously to MTCLK MCOL l Collision detected MCOL The MCOL pin is asserted by the PHY when it detects a collision on the network It remains asserted while the collision condition persists This signal is not necessarily synchronous to MTCLK nor MRCLK This pin is used in half duplex operation only MCRS l Carrier sense MCRS The MCRS pin is asserted by the PHY when the network is not idle in either transmit or receive The pin is de asserted when both transmit and receive are idle This signal is not necessarily synchronous to MTCLK or MRCLK This pin is used in half duplex operation only MRCLK l Receive clock MRCLK The receive clock is a continuous clock that provides the timing reference for receive operations The MRXD MRXDV and MRXER signals are tied to this clock The clock is generated by the PHY and is 2 5 MHz at 10 Mbps operation and 25 MHz at 100 Mbps operation MRXDJ 3 0 l Receive data MRXD The receive data pins are a collection of 4 data signals comprising 4 bits of data MRDXO is the least significant bit LSB The signals are synchronized by MRCLK and valid only when MRXDV is asserted MRXDV l Receive data valid MRXDV The receive data valid signal indicates that the MRXD pins are generating nibble data for use by the EMAC It is driven synchronously to MRCLK MRXER l Receive error MRXER The receive error signal is asserted for one or more MRCLK periods to indicate that an error
116. ated EMAC Port Registers 5 18 MAC Interrupt Status Masked Register MACINTSTATMASKED The MAC interrupt status masked register MACINTSTATMASKED is shown in Figure 60 and described A TEXAS INSTRUMENTS www ti com in Table 54 Figure 60 MAC Interrupt Status Masked Register MACINTSTATMASKED 31 16 Reserved HO 15 2 1 0 HOST STAT Reserved PEND PEND HO HO HO LEGEND R W R Read only n value after reset Table 54 MAC Interrupt Status Masked Register MACINTSTATMASKED Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 HOSTPEND Host pending interrupt HOSTPEND masked interrupt read 0 STATPEND Statistics pending interrupt STATPEND masked interrupt read 112 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Copyright 2006 2010 Texas Instruments Incorporated Submit Documentation Feedback 1 TEXAS INSTRUMENTS www ti com 5 19 MAC Interrupt Mask Set Register MACINTMASKSET The MAC interrupt mask set register MACINTMASKSET is shown in Figure 61 and described in EMAC Port Registers Table 55 Figure 61 MAC Interrupt Mask Set Register MACINTMASKSET 31 16 Reserved R 0 15 2 1 0 HOST STAT Reserved MASK MASK R 0 R WS 0 R WS 0 LEGEND R Read only R W Read Write R WS Read Write 1 to set n value after reset Table 55 MAC Interrupt Mask Set
117. back Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 21 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE The receive multicast broadcast promiscuous channel enable register RXMBPENABLE is shown in Figure 63 and described in Table 57 Figure 63 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE 31 30 29 28 27 25 24 Reserved RXPASSCRG RXQOSEN RXNOCHAIN Reserved RXCMFEN HO R W 0 R W 0 R W 0 R 0 R W 0 23 22 21 20 19 18 16 RXCSFEN RXCEFEN RXCAFEN Reserved RXPROMCH R W 0 R W 0 R W 0 R 0 R W 0 15 14 13 12 11 10 8 Reserved RXBROADEN Reserved RXBROADCH R 0 R W 0 R 0 R W 0 7 6 5 4 3 2 0 Reserved RXMULTEN Reserved RXMULTCH HO R W 0 HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 57 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE Field Descriptions Bit Field Value Description 31 Reserved 0 Reserved 30 RXPASSCRC Pass receive CRC enable bit 0 Received CRC is discarded for all channels and is not included in the buffer descriptor packet length field 1 Received CRC is transferred to memory for all channels and is included in the buffer descriptor packet length 29 RXQOSEN Receive quality of service enable bit 0 Receive QOS is disabled Receive QOS is enabled Receive no buffer
118. ble 16 Emulation Control SOFT FREE Description 0 0 Normal operation 1 0 Emulation suspend xX 1 Normal operation 70 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l www ti com 3 3 1 TEXAS INSTRUMENTS EMIC Module Registers EW_INTCTL Registers There are six EW_INTCTL registers one per C64x megamodule These registers shown in Figure 23 reside in the configuration space of the respective Ethernet wrappers This register controls generation of MACTXINT MACRXINT and MACINT interrupts for each core The interrupts are classified into 3 groups e Common interrupts MDIO_USER MDIO_LINT STAT HOST e Transmit interrupts TXO through TX7 e Receive interrupts RX0 through RX7 Generation of MACINTX is conditional on the following e Atleast one of the pulse interrupts in the common group is enabled e Atleast one of the enabled pulse interrupts in the common group is asserted by EMAC or MDIO Generation of MACTXINTX is conditional on the following e Atleast one of the pulse interrupts in the transmit group is enabled e Atleast one of the enabled pulse interrupts in the transmit group is asserted by EMAC Generation of MACRXINTX is conditional on the following e Atleast one of the pulse interrupts in the receive group is enabled e Atleast one of the enabled pulse interrupts in the rece
119. ble bit is set then a group address that hashes to that bit index is accepted 136 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 39 Back Off Test Register BOFFTEST The back off test register BOFFTEST is shown in Figure 81 and described in Table 75 Figure 81 Back Off Test Register BOFFTEST 31 26 25 16 Reserved RNDNUM R 0 HO 15 12 11 10 9 0 COLLCOUNT Reserved TXBACKOFF R 0 HO R 0 LEGEND R Read only n value after reset Table 75 Back Off Test Register BOFFTEST Field Descriptions Bit Field Value Description 31 26 Reserved 0 Reserved 25 16 RNDNUM Back off random number generator This field allows the Back off Random Number Generator to be read Reading this field returns the generator s current value The value is reset to zero and begins counting on the clock after the de assertion of reset 15 12 COLLCOUNT Collision count These bits indicate the number of collisions the current frame has experienced 11 10 Reserved 0 Reserved 9 0 TXBACKOFF Back off count This field allows the current value of the back off counter to be observed for test purposes This field is loaded automatically according to the back off algorithm and is decremented by one for each slot time after the c
120. but not required The buffer byte count value should not include the CRC bytes if they are present If the SOP buffer descriptor PASSCRC flag is set then the last four bytes of the transmit data are transmitted as the frame CRC The four CRC data bytes should be the last four bytes of the frame and should be included in the buffer byte count value The MAC performs no error checking on the outgoing CRC 2 10 2 3 Adaptive Performance Optimization APO The EMAC incorporates adaptive performance optimization APO logic that may be enabled by setting the TXPACE bit in the MACCONTROL register Transmission pacing to enhance performance is enabled when the TXPACE bit is set Adaptive performance pacing introduces delays into the normal transmission of frames delaying transmission attempts between stations and reducing the probability of collisions occurring during heavy traffic as indicated by frame deferrals and collisions These actions increase the chance of a successful transmission When a frame is deferred suffers a single collision multiple collisions or excessive collisions the pacing counter is loaded with an initial value of 31 When a frame is transmitted successfully without experiencing a deferral single collision multiple collision or excessive collision the pacing counter is decremented by 1 down to 0 If the pacing counter is zero this allows a new frame to immediately attempt transmission after one IPG If the pacing
121. ceive are idle This signal is not necessarily synchronous to MTCLK nor MRCLK This pin is used in half duplex operation only Receive clock MRCLK The receive clock is a continuous clock that provides the timing reference for receive operations The MRXD MRXDV and MRXER signals are tied to this clock The clock is generated by the PHY and is 2 5 MHz at 10 Mbps operation 25 MHz at 100 Mbps operation and 125 MHz at 1000 Mbps operation Receive data MRXD The receive data pins are a collection of 8 data signals comprising 8 bits of data MRDX0O is the least significant bit LSB The signals are synchronized by MRCLK and valid only when MRXDV is asserted Receive data valid MRXDV The receive data valid signal indicates that the MRXD pins are generating nibble data for use by the EMAC It is driven synchronously to M RCLK Receive error MRXER The receive error signal is asserted for one or more MRCLK periods to indicate that an error was detected in the received frame This is meaningful only during data reception when MRXDV is active Management data clock MDCLK The MDIO data clock is sourced by the MDIO module on the system It is used to synchronize MDIO data access operations done on the MDIO pin The frequency of this clock is controlled by the CLKDIV bits in the MDIO control register CONTROL Management data input output MDIO The MDIO pin drives PHY management data into and out of the PHY by way of an access frame consisti
122. cell latency is less than the time required to transmit a 64 byte cell on the wire 0 512 us in 1 Gbps mode 5 12 us in 100 Mbps mode or 51 2us in 10 Mbps mode The latency time includes any required buffer descriptor reads for the cell data Latency to system s internal and external RAM can be controlled through the use of the transfer node priority allocation register in the TC16486 C6472 devices Latency to descriptor RAM is low because RAM is local to the EMAC as it is part of the CPPI buffer manager Transfer Node Priority The TCl6486 C6472 devices contain a system level priority allocation register PRI_ALLOC that sets the priority of the transfer node used in issuing memory transfer requests to system memory Although the EMAC has internal FIFOs to help alleviate memory transfer arbitration problems the average transfer rate of data read and written by the EMAC to internal or external DSP memory must be at least equal to the Ethernet wire rate In addition the internal FIFO system cannot withstand a single memory latency event greater than the time it takes to fill or empty a TXCELLTHRESH number of internal 64 byte FIFO cells SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 63 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com For example for 1000 Mbps operation these restrictions translate into the following
123. chaining bit 28 RXNOCHAIN 0 Received frames can span multiple buffers Receive DMA controller transfers each frame into a single buffer regardless of the frame or buffer size All remaining frame data after the first buffer is discarded The buffer descriptor buffer length field will contain the entire frame byte count up to 65535 bytes 27 25 Reserved 0 24 RXCMFEN Reserved Receive copy MAC control frames enable bit Enables MAC control frames to be transferred to memory MAC control frames are normally acted upon if enabled but not copied to memory MAC control frames that are pause frames will be acted upon if enabled in MACCONTROL regardless of the value of RXCMFEN Frames transferred to memory due to RXCMFEN will have the CONTROL bit set in their EOP buffer descriptor 0 MAC control frames are filtered but acted upon if enabled MAC control frames are transferred to memory Receive copy short frames enable bit Enables frames or fragments shorter than 64 bytes to be copied to memory Frames transferred to memory due to RXCSFEN will have the FRAGMENT or UNDERSIZE bit set in their EOP buffer descriptor Fragments are short frames that contain CRC align code errors and undersized are short frames without errors 23 RXCSFEN 0 Short frames are filtered Short frames are transferred to memory SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 115 Submit Documentation Feedback
124. cing of the EMAC interrupt if there are real time tasks to perform Eight channels are supplied for both transmit and receive operations On transmit the eight channels represent eight independent transmit queues The EMAC can be configured to treat these channels as an equal priority round robin queue or as a set of eight fixed priority queues On receive the eight channels represent eight independent receive queues with packet classification Packets are classified based on the destination MAC address Each of the eight channels is assigned its own MAC address enabling the EMAC module to act like eight virtual MAC adapters Also specific types of frames can be sent to specific channels For example multicast broadcast or other promiscuous error etc frames can each be received on a specific receive channel queue The EMAC tracks 36 different statistics as well as recording the status of each individual packet in its corresponding packet descriptor Media Independent Interfaces The EMACO supports MII GMII RMII S3MII and RGMII physical interfaces to external PHY devices whereas the EMAC1 supports RMII S3MII and RGMII interfaces The following sections discuss the operation of these interfaces in 10 100 Mbps mode MII RMII GMII and RGMII and 1000 Mbps mode GMII and RGMII An IEEE 802 3 compliant Ethernet MAC controls these interfaces Data Reception 2 10 1 1 Receive Control Data received from the PHY is interpreted an
125. clock buffer RX_CLK 28 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 4 Ethernet Protocol Overview Ethernet provides a reliable connectionless service to a networking application A brief overview of the ethernet protocol follows For more information on the carrier sense multiple access with collision detection CSMA CD access method ethernet s multiple access protocol see the IEEE 802 3 standard document 2 4 1 Ethernet Frame Format All the ethernet technologies use the same frame structure The format of an ethernet frame is shown in Figure 9 and described in Table 12 The ethernet packet is the collection of bytes representing the data portion of a single ethernet frame on the wire shown outlined in bold in Figure 9 The ethernet frames are of variable lengths with no frame smaller than 64 bytes or larger than RXMAXLEN bytes header data and CRC Figure 9 Ethernet Frame Number of bytes 7 1 6 6 2 46 RXMAXLEN 18 4 Legend SFD Start Frame Delimiter FCS Frame Check Sequence CRC Table 12 Ethernet Frame Description Field Bytes Description Preamble 7 These 7 bytes have a fixed value of 55h They wake up the receiving EMAC ports and synchronize their clocks to that of the sender s clock Start of Frame 1 This field with a value of 5Dh
126. d Media Independent Interface RMII Connections Figure 3 shows a TCI6486 C6472 device with integrated EMAC and MDIO interfaced to the PHY via an RMII connection This interface is available only in 10 Mbps and 100 Mbps modes Figure 3 Ethernet Configuration with RMIl Interface 50 MHz zero delay clock buffer RMREFCLK RMREFCLK RMTXD 1 0 RMTXEN RMCRSDV Physical layer device PHY RMRXD 1 0 RMRXER The RMIl interface has the same functionality as the MII but it does so with a reduced number of pins thus lowering the total cost for an application In devices incorporating many PHY interfaces such as switches the number of pins can add significant cost as the port counts increase Table 8 summarizes the individual EMAC and MDIO signals for the RMII interface The RMIl interface does not include an MCOL signal A collision is detected from the receive and transmit data delimiters The data signals are 2 bits wide and a single reference clock must be provided to the MAC operating at 50 MHz to sustain the same data rate as MIl Table 8 EMAC and MDIO Signals for RMII Interface Signal Name UO Description RMTXD 1 0 O Transmit data RMTXD The transmit data pins are a collection of 2 data signals comprising 2 bits of data RMTDXO is the least significant bit LSB The signals are synchronized to the RMII reference clock and valid only when RMTXEN is asserted RMTXEN O Transmit enable
127. d Register RXnFLOWTHRESH Field Descriptions 123 64 Receive Channel n Free Buffer Count Register RXnFREEBUFFER Field Descriptions eeeeee 124 65 MAC Control Register MACCONTROL Field Descriptions cceeeeee eee eeee nese eee eee nese eeeeeeeeeenaeeee 125 66 MAC Status Register MACSTATUS Field Descrpttons eee ee reese eee ee eens seen nese eeeeeeeaeeee 127 67 Emulation Control Register EMCONTROL Field Descriptions ccceeeeeeeeee eee eeeeeeeeeeeeeeeeeeeeneee 129 68 FIFO Control Register FIFOCONTROL Field Descriptions eee eee eee eee teen eeeeeeeeeeeeeneee 130 69 MAC Configuration Register MACCONFIG Field Descriptions seceeee ence este eeee nese eeeeeeeeeeeaeeee 131 70 Soft Reset Register SOFTRESET Field Descriptions cceeeee eee ee eee eee teen nese ee eee sees eeeeeeeeaeeee 132 71 MAC Source Address Low Bytes Register MACSRCADDRLO Field Descriptions eesceeeeeeeeeeee 133 72 MAC Source Address High Bytes Register MACSRCADDRHI Field Description 134 73 MAC Hash Address Register 1 MACHASH1 Field Descriptions sees eeeeeeeeeeeeeees 135 74 MAC Hash Address Register 2 MACHASH2 Field Descriptions seen eee eee eee eeeeeeeeeeeeeeees 136 75 Back Off Test Register BOFFTEST Field Descriptions cceeeeeeeeeeee eee eee eeeeeeeeeeeeeeeeeeeeenenees 137 76 Transmit Pacing Algorithm Test Register TRACETEST Field Descriptions ceeceeeeeeeeeeeeeeeeeeeees 138 7
128. d output to the EMAC receive FIFO Interpretation involves detection and removal of the preamble and start of frame delimiter extraction of the address and frame length data handling error checking and reporting cyclic redundancy checking CRC and statistics control signal generation Receive address detection and frame filtering of the frames that do not address match is performed outside the Media Independent interface 2 10 1 2 Receive Inter Frame Interval The 802 3 required inter packet gap IPG is 24 receive data clocks 96 bit times However the EMAC can tolerate a reduced IPG 2 receive clocks in 10 100 Mbps mode and 5 receive clocks in 1000 Mbps mode with a correct preamble and start frame delimiter This interval between frames must comprise in the following order 1 An Inter Packet Gap IPG 2 A seven bytes preamble all bytes 55h 3 Aone byte start of frame delimiter 5Dh 2 10 1 3 Receive Flow Control 54 When enabled and triggered receive flow control is initiated to limit the EMAC from further frame reception Two forms of receive flow control are implemented on the TC16486 C6472 device e Receive buffer flow control e Receive FIFO flow control When enabled and triggered receive buffer flow control prevents further frame reception based on the number of free buffers available Receive buffer flow control issues flow control collisions in half duplex mode and IEEE 802 3X pause frames for full duplex mode
129. device driver initialize the MDIO device perform the following 1 Configure the PREAMBLE and CLKDIV bits in the CONTROL register 2 Enable the MDIO module by setting the ENABLE bit in the CONTROL register 3 The ALIVE register can be read after a delay to determine which PHYs responded and the LINK register can determine which of those if any already have a link 4 Set up the appropriate PHY addresses in the USERPHYSELn register and set the LINKINTENB bit to enable a link change event interrupt if desirable 5 If an interrupt on a general MDIO register access is desired set the corresponding bit in the USERINTMASKSET register to use the USERACCESSn register If only one PHY is to be used the application software can set up one of the USERACCESSn registers to trigger a completion interrupt The other register is not set up SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 49 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 8 2 2 Writing Data to a PHY Register The MDIO module includes a user access register USERACCESSn to directly access a specified PHY device To write a PHY register perform the following 1 Ensure that the GO bit in the USERACCESSn register is cleared 2 Write to the GO WRITE REGADR PHYADR and DATA bits in USERACCESSn corresponding to the desired PHY and PHY register 3 The w
130. did not have the resources to receive it cell FIFO full or no DMA buffer available after the frame was successfully started no SOF overrun CRC errors alignment errors and code errors have no effect on this statistic 5 50 36 Receive DMA Start of Frame and Middle of Frame Overruns Register RXDMAOVERRUNS 156 The total number of frames received on the EMAC that had either a DMA start of frame SOF overrun or a DMA middle of frame MOF overrun A receive DMA overrun frame is defined as having all of the following e Was any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of any size including less than 64 byte and greater than RXMAXLEN byte frames e The EMAC was unable to receive it because it did not have the DMA buffer resources to receive it zero head descriptor pointer at the start or during the middle of the frame reception CRC errors alignment errors and code errors have no effect on this statistic C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Appendix A Glossary Broadcast MAC Address A special Ethernet MAC address used to send data to all Ethernet devices on the local network The broadcast address is FFh FFh FFh FFh FFh FFh The LSB of the first byte is odd qualifying it as a group address
131. e A 48 bit 6 bytes destination address equal to The destination station s individual unicast address The destination station s multicast address MACHASH1 and MACHASH2 registers The broadcast address of all ones e A 48 byte 6 bytes source address e The 16 bit 2 bytes length type field containing the value 81 00h e The 16 bit 2 bytes TCI field with the priority field in the upper 3 bits e Data bytes e The 4 bytes CRC The RXFILTERLOWTHRESH and the RXnFREEBUFFER registers are used in conjunction with the priority information to implement receive hardware QOS Low priority frames are filtered if the number of free buffers RXnFREEBUFFER for the frame channel is less than or equal to the filter low threshold RXFILTERLOWTHRESH value Hardware QOS is enabled by the RXQOSEN bit in the RXMBPENABLE register Host Free Buffer Tracking The host must track free buffers for each enabled channel including unicast multicast broadcast and promiscuous if receive QOS or receive flow control is used Disabled channel free buffer values are don t cares During initialization the host should write the number of free buffers for each enabled channel to the appropriate RXnFREEBUFFER register The EMAC decrements the appropriate channel s free buffer value for each buffer used When the host reclaims the frame buffers the host should write the channel free buffer register with the number of reclaimed buffers write to increment There ar
132. e a maximum of 65 535 free buffers available The RXnFREEBUFFER registers only need to be updated by the host if receive QOS or flow control is used SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 59 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 11 6 Receive Channel Teardown The host commands a receive channel teardown by writing the channel number to the RXTEARDOWN register When a teardown command is issued to an enabled receive channel the following occurs e Any current frame in reception completes normally e The TDOWNCMPLT flag is set in the next buffer descriptor in the chain if there is one e The channel head descriptor pointer is cleared e A receive interrupt for the channel is issued to the host e The corresponding RXnCP register contains the value FFFF FFFCh e The host should acknowledge a teardown interrupt with an FFFF FFFCh acknowledge value Channel teardown may be commanded on any channel at any time The host is informed of the teardown completion by the set teardown complete buffer descriptor bit The EMAC does not clear any channel enables due to a teardown command A teardown command to an inactive channel issues an interrupt that software should acknowledge with an FFFF FFFCh acknowledge value to RXnCP note that there is no buffer descriptor in this case Software may read RXnCP to
133. e enable a write of 0 has no effect May be read 6 RXCH6EN Receive channel 6 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 5 RXCH5EN Receive channel 5 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 4 RXCH4EN Receive channel 4 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 3 RXCH3EN Receive channel 3 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 2 RXCH2EN Receive channel 2 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 1 RXCH1EN Receive channel 1 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 0 RXCHOEN Receive channel 0 unicast enable set bit Write 1 to set the enable a write of 0 has no effect May be read 118 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 23 Receive Unicast Clear Register RXUNICASTCLEAR The receive unicast clear register RXUNICASTCLEAR is shown in Figure 65 and described in Table 59 Figure 65 Receive Unicast Clear Register RXUNICASTCLEAR 31 16 Reserved HO 15 8 7 6 5 4 3 2 1 0 Reserved RXCH7EN RXCH6EN RXCH5EN RXCH4EN RXCHS3EN
134. e frame is filtered and not transferred to memory MAC control frames are transferred to memory if the RXCMFEN bit in the RXMBPENABLE register is set The TXFLOWEN and FULLDUPLEX bits affect whether MAC control frames are acted upon but they have no effect upon whether MAC control frames are transferred to memory or filtered Pause frames are a subset of MAC control frames with an opcode field of 0001h Incoming pause frames are only acted upon by the EMAC if the following conditions occur e The TXFLOWEN bit is set in the MACCONTROL register e The frame s length is between 64 bytes and RXM AXLEN bytes inclusive e The frame contains no CRC error or align code errors The pause time value from valid frames is extracted from the two bytes following the opcode The pause time is loaded into the EMAC transmit pause timer and the transmit pause time period begins If a valid pause frame is received during the transmit pause time period of a previous transmit pause frame then either the destination address is not equal to the reserved multicast address or any enabled or disabled unicast address and the transmit pause timer immediately expires or the new pause time value is 0 and the transmit pause timer immediately expires Otherwise the EMAC transmit pause timer is set immediately to the new pause frame pause time value Any remaining pause time from the previous pause frame is discarded If the TXFLOWEN bit in MACCONTROL is cleared then the
135. e of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice TI is not responsible or liable for any such statements TI products are not authorized for use in safety critical applications such as life support where a failure of the TI product would reasonably be expected to cause severe personal injury or death unless officers of the parties have executed an agreement specifically governing such use Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications and acknowledge and agree that they are solely responsible for all legal regulatory and safety related requirements concerning their products and any use of TI products in such safety critical applications notwithstanding any applications related information or support that may be provided by TI Further Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety critical applications TI products are neither designed nor intended for use in military aerospace applications or environments unless the TI products are specifically designated by TI as military grade or enhanced plastic Only products designated by TI as military grade meet military specifications Buyers ackn
136. eceeeeeeeeeeeeee eee eeeeeeeeeeeeeeeeenee 146 5 49 Receive Channel 0 7 Completion Pointer Register RXNCP cceeeeeeee eee eee eee eee nese eeeeeeeeeeeeeeee 147 5 50 INGtWOrk Statisties REGISLEPS Zeetegebegeg ee deg ENEE AE 148 Appendix A Glossary ageet gees EE e 157 Appendix B Revision History euegegegegekSENESESKSK EN ENEE cease ct ec ctetsednseiese EES ESNEERN ENEE EE ENEE EN ENNEN 159 SPRUEF8F March 2006 Revised November 2010 Contents 5 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS www ti com List of Figures 1 EMAC and MDIO Block Diaetant eege NEE NK EANE EN ES Ne NEEN SES NES E de AR aa SES 12 2 Ethernet Configuration with MII Interface cceceeee cece ence eee e eee eee eee eee e eee nae ease eee eeeeeeenaeeeeeeeeeaees 18 3 Ethernet Configuration with RMII Interface EE 20 4 Ethernet Configuration with GMII Interface A 21 5 Ethernet Configuration with RGMII Interface AN 23 6 Ethernet Configuration with S3MII Interface EEN 25 7 SOMILMUITAPELY Contiguratio TEE 27 8 SoMIl Switch ConliQuratiOn EE 28 9 Ethernet Fraime gege d en AER ENEE EE DEENEN Ee ENEE dee Ee ENEE Eege 29 10 Basic Descriptor FORM at iecicwaisincney SEVEN EE NKNENN ENKEN ER EN ENER SEENEN E NENNEN ENNEN EN EEN ENEE eEENeN 31 11 Typical Descriptor Linked US ou eu ENNEN neve NENNENNKENK ENEE ENER ENNEN E SEENEN ENEE KEEN SEENEN ENEE EN een 32 12 Transmit Descriptor Format 34 13 Receive
137. ects and processes incoming network frames de frames them and places them into the receive FIFO The MAC receiver also detects errors and passes statistics to the statistics RAM Receive address sub module The receive address sub module performs address matching and address filtering based on the incoming packet s destination address It contains a 32 x 53 bit two port RAM in which up to 32 addresses can be stored to be either matched or filtered by the EMAC The RAM may contain multicast packet addresses but the associated channel must have the unicast enable bit set even though it is a multicast address The unicast enable bits are used with multicast addresses in the receive address RAM not the multicast hash enable bits Therefore hash matches can be disabled but specific multicast addresses can be matched or filtered in the RAM If a multicast packet hash matches the packet may still be filtered in the RAM Each packet Configuration bus 52 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture can be sent to only a single channel e The transmit path Transmit DMA engine The transmit DMA engine performs the data transfer between the device internal or external memory and the transmit FIFO It interfaces to the processor through the bus arbiter in the C
138. ed November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 13 Receive Interrupt Status Unmasked Register RXINTSTATRAW The receive interrupt status unmasked register RXINTSTATRAW is shown in Figure 55 and described in Table 49 Figure 55 Receive Interrupt Status Unmasked Register RXINTSTATRAW 31 16 Reserved HO 15 8 7 6 5 4 3 2 1 0 Reserved RX7 RX6 RX5 RX4 RX3 RX2 SEA RX0 PEND PEND PEND PEND PEND PEND PEND PEND R 0 HO HO R 0 HO HO HO HO HO LEGEND R Read only n value after reset Table 49 Receive Interrupt Status Unmasked Register RXINTSTATRAW Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 RX7PEND RX7PEND raw interrupt read before mask 6 RX6PEND RX6PEND raw interrupt read before mask 5 RX5PEND RX5PEND raw interrupt read before mask 4 RX4PEND RX4PEND raw interrupt read before mask 3 RX3PEND RX3PEND raw interrupt read before mask 2 RX2PEND RX2PEND raw interrupt read before mask 1 RX1PEND RX1PEND raw interrupt read before mask 0 RXOPEND RXOPEND raw interrupt read before mask SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 107 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INS
139. educed pin alternative to the GMII interface The data paths are reduced control signals are multiplexed together and both edges of the clock are used The RGMII interface does not include a MCOL and a MCRS signal for half duplex mode only available in 10 100 Mbps mode Carrier sense MCRS is indicated by one of the following cases instead e MRXDV signal multiplexed in the RGRXCTL signal is true e MRXDV is false MRXERR multiplexed in the RGRXCTL signal is true and a value of FFh exists on the RGRXDJ3 0 simultaneously Table 10 summarizes the individual EMAC and MDIO signals for the RGMII interface Table 10 EMAC and MDIO Signals for RGMII Interface Signal Name UO Description RGTXC O Transmit clock RGTXC The transmit clock is a continuous clock that provides the timing reference for transmit operations The RGTXD and RGTXCTL signals are tied to this clock The clock is driven by the EMAC and is 2 5 MHz at 10 Mbps operation 25 MHz at 100 Mbps operation and 125 MHz at 1000 Mbps operation RGTXD 3 0 O Transmit data RGTXD The transmit data pins are a collection of 4 data signals comprising 4 bits of data RGTDXO is the least significant bit LSB The signals are synchronized by RGTXC and valid only when RGTXCTL is asserted The lower 4 bits of data are transmitted on the rising edge of the clock and the higher 4 bits of data are transmitted on the falling edge of the RGTXC RGTXCTL O Transmit enable RGTXCTL The
140. eeee eee eee eee eee eee e eee eeeeeeeeaeeeeeeeeeeees 77 23 MDIO Control Register CONTROL Field Descriptions ceeee eee ee eee eee eee eee eee nese eee eee nese eeeneees 78 24 PHY Acknowledge Status Register ALIVE Field Descriptions sssssssssssssnnnrnrnnnnnnnennnnnnnnnnnnnnnnn 79 25 PHY Link Status Register LINK Field Descriptions 0cceeeeee eee eee nese eee eee seen eee eeeeeeeeeeeeeeeeeeaees 80 26 MDIO Link Status Change Interrupt Unmasked Register LINKINTRAW Field Descriptions 81 27 MDIO Link Status Change Interrupt Masked Register LINKINTMASKED Field Descriptions 82 28 MDIO User Command Complete Interrupt Unmasked Register USERINTRAW Field Descriptions 83 29 MDIO User Command Complete Interrupt Masked Register USERINTMASKED Field Descriptions 84 30 MDIO User Command Complete Interrupt Mask Set Register USERINTMASKSET Field Descriptions 85 31 MDIO User Command Complete Interrupt Mask Clear Register USERINTMASKCLEAR Field DS SCID le 86 32 MDIO User Access Register 0 USERACCESSO Field Descriptions sees eee eeeeeeeeeeeeeeeees 87 33 MDIO User PHY Select Register 0 USERPHYSELO Field Descriptions ceceeeeeeeeeeeeeeeeeeeeeeees 88 34 MDIO User Access Register 1 USERACCESS1 Field Descriptions sees eeeeeeeeeeeeeeeees 89 35 MDIO User PHY Select Register 1 USERPHYSEL1 Field Descriptions cccceeeeeeeeeeeeeeeeeeeeeeeee 90 36 Ethernet Med
141. eeeee 134 79 MAC Hash Address Register 1 MACHAGHT eee e enter eee eee e eee ee snes eee eeeenaeeeeeeeeeeeeeeeeeees 135 80 MAC Hash Address Register 2 MACHAGHD cece renee teen een eee ee sees eeeeneeeaeeeeeeeeeeeeeaeeeees 136 81 Back Off Test Register BOFFTEST snsiccceinncteccnna gsgeghu ge SEENEN SNE a 137 82 Transmit Pacing Algorithm Test Register TPACETEST cseceeeeeee cess eee eeeeeeeeeeeeeeeeeeeeeeeeeeeneees 138 83 Receive Pause Timer Register RXPAUSE EEN 139 84 Transmit Pause Timer Register TXPAUSE ENEE 140 85 MAC Address Low Bytes Register MAC ADDPL ON 141 86 MAC Address High Bytes Register MACADDRHI A 142 87 MAC Index Register MACINDEX cecceeee eee e eee eee eee eee eee eee eee n eens ene e teen eee n aetna eee e eee e nee eae eee 143 88 Transmit Channel n DMA Head Descriptor Pointer Register TXNHDP A 144 89 Receive Channel n DMA Head Descriptor Pointer Register DX oHlDP 145 90 Transmit Channel n Completion Pointer Register TI XnChi 146 91 Receive Channel n Completion Pointer Register Do 147 92 Statistics EE 148 SPRUEF8F March 2006 Revised November 2010 List of Figures 7 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS www ti com List of Tables 1 Serial Management Interface PINS cceeeee ee eee eee rete eee e eee eee een etna eee nee nets eee e nee eee ee ene 13 2 EMAC EN Pin Description asics cece NENNEN SEHR REENEN
142. eeeeeeeeeeee 133 5 36 MAC Source Address High Bytes Register MACSRCADDRHI seceeee seen eee ee eee eee eeeeeeeeeeeeee 134 5 37 MAC Hash Address Register 1 MACHASH1 cceeeeee eee eee eee ee eee tease neces sees tees neeeeeeaeeeneeee 135 5 38 MAC Hash Address Register 2 MACHASH2 ccceee eee eee ee eee nent nena enna snes ease eee eeeeaeenaeeeeeeee 136 539 Back Oif Test Register BORF TEST eege enn EEN 137 5 40 Transmit Pacing Algorithm Test Register TPACETEST cceeeeeeeee cece tent eee eee teen eeeeeeeeeeeeeeeee 138 5 41 Receive Pause Timer Register RXPAUSE cccecceee cece ee eee tees eee eee tees eee eee seas eneeeeeeaeeeaeneeeeee 139 5 42 Transmit Pause Timer Register TXPAUSE seceeeeeee eee ee eee eee eee ee ee eee eee eae teen eee eeeeeaeeeeeeee 140 4 Contents SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated AA TEXAS INSTRUMENTS www ti com 5 43 MAC Address Low Bytes Register MACADDRLO 0cseeeeee cece ee eee eee eee eee sees eeeeeeeeeeeeaeeeeeeee 141 5 44 MAC Address High Bytes Register MACADDRHI 142 5 45 MAC Index Register MACINDEX EEN 143 5 46 Transmit Channel 0 7 DMA Head Descriptor Pointer Register TXNHDP AN 144 5 47 Receive Channel 0 7 DMA Head Descriptor Pointer Register RXNHDP eceeeeeeeeeeeeeeeeeeeeeeee 145 5 48 Transmit Channel 0 7 Completion Pointer Register TXNCP cs
143. eeeeeeeeeees 83 36 MDIO User Command Complete Interrupt Masked Register USERINTMASKED eeeeeeeeeeeeeeees 84 37 MDIO User Command Complete Interrupt Mask Set Register USERINTMASKSET 0 seeeeeeeeeeeeeeees 85 38 MDIO User Command Complete Interrupt Mask Clear Register USERINTMASKCLEAR An 86 39 MDIO User Access Register 0 UGERACCEGGO cece eee e eens teen eee eeeeeeeneeeeeeneeeeeeneeeeeeeees 87 40 MDIO User PHY Select Register 0 USERPHYSELO eee eee eee eee e tees eee eeeeeeeeeeeeeeeeeeeeenaes 88 41 MDIO User Access Register 1 USERACCESS1 ssssssssssnunnrrrrrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 89 42 MDIO User PHY Select Register 1 USERPHYSEL1 EEN 90 43 Transmit Identification and Version Register TXIDVER e 95 44 Transmit Control Register TXGON HOER ENEE 96 45 Transmit Teardown Register TXTEARDOWN A 97 46 Receive Identification and Version Register RSIDVER E 98 47 Receive Control Register RXCONTROL eeceee eee ence ee eee eee ee eee e eee eee eee eaeenee nese eeeeaeneeeeeeneeeaees 99 List of Figures SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated AA TEXAS INSTRUMENTS www ti com 48 Receive Teardown Register RXTEARDOWN cceeceee ence eee eee eee e eee ee eeeeeeeee seas eeeeeeenaeenaeeeeneee 100 49 Transmit Interrupt Status Unmasked Register TSINTGTATRAMW 101 50 Transmit Interrupt Status Masked Regist
144. egister is 0 to Buffer Length 1 for the smallest value of buffer length for all descriptors in the list 2 5 5 4 Buffer Length This 16 bit field has two functions e Before the descriptor is first placed on the receive queue by the application software the software initializes the buffer length field with the physical size of the empty data buffer specified by the buffer pointer field e After the empty buffer has been processed by the EMAC and filled with received data bytes the EMAC updates the buffer length field to reflect the actual number of valid data bytes written to the buffer 2 5 5 5 Packet Length This 16 bit field specifies the number of data bytes in the entire packet The software application initializes this value to zero for empty packet buffers The EMAC fills in the value on the first buffer used for a given packet as signified by the EMAC setting a start of packet SOP flag The EMAC sets the packet length on all SOP buffer descriptors 2 5 5 6 Start of Packet SOP Flag 38 When set this flag indicates that the descriptor points to the starting packet buffer of a new packet For a single fragment packet both the SOP and end of packet EOP flags are set Otherwise the descriptor pointing to the last packet buffer for the packet has the EOP flag set The software application initially clears this flag before adding the descriptor to the receive queue The EMAC sets this bit on SOP descriptors C6472 TCI6486
145. eive Control Register Section 5 5 18h RXTEARDOWN Receive Teardown Register Section 5 6 80h TXINTSTATRAW Transmit Interrupt Status Unmasked Register Section 5 7 84h TXINTSTATMASKED Transmit Interrupt Status Masked Register Section 5 8 88h TXINTMASKSET Transmit Interrupt Mask Set Register Section 5 9 8Ch TXINTMASKCLEAR Transmit Interrupt Clear Register Section 5 10 90h MACINVECTOR MAC Input Vector Register Section 5 11 94h MACEOIVECTOR MAC End of Interrupt Vector Register Section 5 12 AOh RXINTSTATRAW Receive Interrupt Status Unmasked Register Section 5 13 A4h RXINTSTATMASKED Receive Interrupt Status Masked Register Section 5 14 A8h RXINTMASKSET Receive Interrupt Mask Set Register Section 5 15 ACh RXINTMASKCLEAR Receive Interrupt Mask Clear Register Section 5 16 Boh MACINTSTATRAW MAC Interrupt Status Unmasked Register Section 5 17 B4h MACINTSTATMASKED MAC Interrupt Status Masked Register Section 5 18 B8h MACINTMASKSET MAC Interrupt Mask Set Register Section 5 19 BCh MACINTMASKCLEAR MAC Interrupt Mask Clear Register Section 5 20 100h RXMBPENABLE Receive Multicast Broadcast Promiscuous Channel Enable Section 5 21 Register 104h RXUNICASTSET Receive Unicast Enable Set Register Section 5 22 108h RXUNICASTCLEAR Receive Unicast Clear Register Section 5 23 10Ch RXMAXLEN Receive Maximum Length Register Section 5 24 110h RXBUFFEROFFSET Receive Buffer Offset Register Section 5 25 114h RXFILTERLOWTHRESH Receive Filter Low Priority Frame Threshold Register
146. eive channel 3 pending interrupt mask Write 1 to disable interrupt 2 RX2PENDMASK 0 Receive channel 2 pending interrupt mask Write 1 to disable interrupt 1 RX1PENDMASK 0 Receive channel 1 pending interrupt mask Write 1 to disable interrupt 0 RXOPENDMASK 0 Receive channel 0 pending interrupt mask Write 1 to disable interrupt 110 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 17 MAC Interrupt Status Unmasked Register MACINTSTATRAW The MAC interrupt status unmasked register MACINTSTATRAW is shown in Figure 59 and described in Table 53 Figure 59 MAC Interrupt Status Unmasked Register MACINTSTATRAW 31 16 Reserved HO 15 2 1 0 HOST STAT Reserved PEND PEND R 0 HO R 0 LEGEND R Read only n value after reset Table 53 MAC Interrupt Status Unmasked Register MACINTSTATRAW Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 HOSTPEND Host pending interrupt HOSTPEND raw interrupt read before mask 0 STATPEND Statistics pending interrupt STATPEND raw interrupt read before mask SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 111 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorpor
147. eive channel 5 6h Teardown receive channel 6 7h Teardown receive channel 7 100 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 7 Transmit Interrupt Status Unmasked Register TXINTSTATRAW The transmit interrupt status unmasked register TXINTSTATRAW is shown in Figure 49 and described in Table 43 Figure 49 Transmit Interrupt Status Unmasked Register TXINTSTATRAW 31 16 Reserved HO 15 8 7 6 5 4 3 2 1 0 Biesanied TX7 TX6 TX5 TX4 TX3 TX2 TX1 TXO PEND PEND PEND PEND PEND PEND PEND PEND R 0 R 0 R 0 HO HO HO R 0 R 0 R 0 LEGEND R Read only n value after reset Table 43 Transmit Interrupt Status Unmasked Register TXINTSTATRAW Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 TX7PEND TX7PEND raw interrupt read before mask 6 TX6PEND TX6PEND raw interrupt read before mask 5 TX5PEND TX5PEND raw interrupt read before mask 4 TX4PEND TX4PEND raw interrupt read before mask 3 TX3PEND TX3PEND raw interrupt read before mask 2 TX2PEND TX2PEND raw interrupt read before mask 1 TX1PEND TX1PEND raw interrupt read before mask 0 TXOPEND TXOPEND raw interrupt read before mask SPRUEF8F March 2006
148. eive queue for a given receive channel and that the corresponding receiver channel has halted The software application initially clears this flag prior to adding the descriptor to the receive queue The EMAC sets this bit when the EMAC identifies that a descriptor is the last for a given packet received it also sets the EOP flag and there are no more descriptors in the receive list the next descriptor pointer is NULL The software application uses this bit to detect when the EMAC receiver for the corresponding channel has halted This is useful when the application appends additional free buffer descriptors to an active receive queue Note that this flag is valid on EOP descriptors only 2 5 5 10 Teardown Complete TDOWNCMPLT Flag This flag is used when a receive queue is being torn down or aborted instead of being filled with received data such as during device driver reset or shutdown conditions The EMAC sets this bit in the descriptor of the first free buffer when the teardown occurs No additional queue processing is performed 2 5 5 11 Pass CRC PASSCRC Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet includes the 4 byte CRC The software application must clear this flag before submitting the descriptor to the receive queue 2 5 5 12 Jabber Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet is a jabber frame and was not discarded because the RXCEFEN bit was set in t
149. ements on each occasion if a frame experiences multiple collisions and increments on late collisions CRC errors have no effect on this statistic e When the EMAC is in half duplex mode flow control is active and a frame reception begins 5 50 20 Transmit Single Collision Frames Register TXSINGLECOLL The total number of frames transmitted on the EMAC that experienced exactly one collision Such a frame is defined as having all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address 152 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers e Was any size e Had no carrier loss and no underrun e Experienced one collision before successful transmission The collision was not late CRC errors have no effect on this statistic 5 50 21 Transmit Multiple Collision Frames Register TXMULTICOLL The total number of frames transmitted on the EMAC that experienced multiple collisions Such a frame is defined as having all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address e Was any size e Had no carrier loss and no underrun e Experienced 2 to 15 collisions before being successfully transmitted None of the collisions were late CRC errors have no effect on this statis
150. ents the size of the empty buffer The flags field contains more information about the buffer such as whether it is the first fragment in a packet SOP the last fragment in a packet EOP or contains an entire contiguous Ethernet packet both SOP and EOP Section 2 5 4 and Section 2 5 5 describe the flags The packet length only has meaning for buffers that both contain data and are the start of a new packet SOP For SOP descriptors the packet length field contains the length of the entire Ethernet packet even if it is contained in a single buffer or fragmented over several buffers SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 31 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 5 2 32 For example consider three packets to be transmitted Packet A is a single fragment 60 bytes Packet B is fragmented over three buffers 1514 bytes total and Packet C is a single fragment 1514 bytes Figure 11 shows the linked list of descriptors to describe these three packets Figure 11 Typical Descriptor Linked List pNext pBuffer Packet A 0 60 bytes SOP EOP Packet B Fragment 1 512 bytes Packet B Fragment 2 502 bytes Packet B Fragment 3 500 bytes pNext NULL pBuffer Packet C 0 1514 1514 bytes SOP EOP 1514 Tr
151. er TXINTSTATMASKED eeeeeeeee ence eeeeeeeeeeeeeeeeeeeees 102 51 Transmit Interrupt Mask Set Register TXINTMASKSET 0cceeeeeeeee eee e eee eee ee eens eeeeeeenaeeneeeeeeaees 103 52 Transmit Interrupt Mask Clear Register TXINTMASKCLEAR 0cseceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 104 53 MAC Input Vector Register MACINVECTOR eee eee teen eee e eee ee snes eee eeeeeaeenaeeeeeeeeeeeeeeees 105 54 MAC End of Interrupt Vector Register MAC EOINEC TO 106 55 Receive Interrupt Status Unmasked Register RXINTSTATRAW ceeceeeeeeeeee ences eeeeeeeeeeeeeeeeneee 107 56 Receive Interrupt Status Masked Register HXINTSTATMAGRED 108 57 Receive Interrupt Mask Set Register RXINTMASKSET eceeeeeee eee eee ence nesses sees eeeeeeeeeeeeaeeeeeeee 109 58 Receive Interrupt Mask Clear Register RXINTMASKCLEAR eeeeceeee eee eeeee eect eeeeeeeeeeneeeeeneee 110 59 MAC Interrupt Status Unmasked Register MACINTSTATRAW 0cseceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee 111 60 MAC Interrupt Status Masked Register MACINTSTATMASKED 0cseeeeee sees eee eeeeeeeeeeeeeeeeeeeeees 112 61 MAC Interrupt Mask Set Register MACINTMAGKGETI eens sees eeeeeeeeeeeeeteeeeeeteeeeaeeee 113 62 MAC Interrupt Mask Clear Register MACINTMASKCLEAR 0cceeeeeeeee eee eeeeeeeeeeeeeeeeeeeeeeeeeaeees 114 63 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE AN 115 64 Receive Unicast Enable Set Register DXSUINIKCAGTGE
152. ers Receive Channel Enabling Each of the eight receive channels has an enable bit RXCHnEN in the RXUNICASTSET register that is controlled using the RXUNICASTSET and RXUNICASTCLEAR registers The RXCHnEN bits determine whether the given channel is enabled when set to 1 to receive frames with a matching unicast or multicast destination address The RXBROADEN bit in the RXMBPENABLE register determines if broadcast frames are enabled or filtered If broadcast frames are enabled then they are copied to only a single channel selected by the RXBROADCH field of RXMBPENABLE register The RXMULTEN bit in the RXMBPENABLE register determines if hash matching multicast frames are enabled or filtered Incoming multicast addresses group addresses are hashed into an index in the hash table If the indexed bit is set the frame hash will match and it will be transferred to the channel selected by the RXMULTCH field when multicast frames are enabled The multicast hash bits are set in the MACHASH1 and MACHASH2 registers The RXPROMCH bits in the RXMBPENABLE register select the promiscuous channel to receive frames selected by the RXCMFEN RXCSFEN RXCEFEN and RXCAFEN bits These four bits allow reception of MAC control frames short frames error frames and all frames promiscuous respectively The address RAM can be configured to set multiple unicast and or multicast addresses to a given channel if the match bit is set in the RAM Multicast addresses
153. erved 1 0 DIV_SM Divide by N SM 00 Divide by N SM in WAITING state 01 Divide by N SM in DELAY state 10 Divide by N SM in OUTPUT state 11 Reserved SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 73 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS EMIC Module Registers www ti com 3 3 TPIC Registers 3 3 1 TPCFG Registers There are eight TPCFG registers TPCFGO through TPCFG7 one per transmit event This register configuration is common to all C64x megamodules The TPCFG register details are shown in Figure 26 and described in Table 19 Figure 26 TPCFG Register 31 28 27 16 Reserved TIME_CFG 0000 R W 0000 0000 15 8 7 4 3 2 1 0 CNT_CFG Reserved TU CU TR CR R W 0000 0000 0000 R W 0 R W 0 R W 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 19 TPCFG Register Field Descriptions Bit Field Value Description 31 28 Reserved Reserved 27 16 TIME_CFG Time delay configuration value 15 8 CNT_CFG Divide by N configuration value 7 4 Reserved Reserved 3 TU Write only bit reads return 0 0 N A Enables writes to TIME_CFG 2 CU Write only bit reads return 0 0 N A Enables writes to CNT_CFG 1 TR Write only bit reads return 0 0 N A Resets the timer counter 0 CR Write only bit reads return 0 0 N A Resets the divide by N count
154. escriptors as it transfers data to or from the buffers The EMIC module associated with each EMAC takes a single set of interrupts from respective EMAC and common MDIO and creates six different sets of TX RX and common interrupts to six cores of the TC1I6486 C6472 device In addition this module implements the interrupt pacing operation The control registers of the EMAC and MDIO modules are memory mapped into device memory space via the device configuration bus The MDIO module implements the 802 3 serial management interface to interrogate and control up to 32 Ethernet PHYs connected to the device using a shared two wire bus Application software uses the MDIO module to configure the auto negotiation parameters of each PHY attached to the EMAC retrieve the negotiation results and configure required parameters in the EMAC module for correct operation The module is designed to allow almost transparent operation of the MDIO interface with very little maintenance from the core processor A single MDIO is shared by both EMACs MACSELO 2 0 and MACSEL1 1 0 are device configuration pins used to select the MII interface for EMACO and EMAC1 respectively The MDIO communicates to PHY through two signals MDCLK output clock and MDIO bi directional data For details of MDIO operation and signals see Section 2 8 The device has two serial management interfaces although only one is used based on the interface selection of EMACO Table 1 shows the
155. fault value is 0 which implies that the link status is determined by the MDIO state machine This is the only option supported on this device 6 LINKINTENB Link change interrupt enable Set to 1 to enable link change status interrupts for PHY address specified in PHYADRMON Link change interrupts are disabled if this bit is set to 0 0 Link change interrupts are disabled Link change status interrupts for PHY address specified in PHYADDRMON bits are enabled 5 Reserved 0 Reserved 4 0 PHYADRMON PHY address whose link status is to be monitored 90 C6472 TC16486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 5 EMAC Port Registers Table 36 lists the memory mapped registers for the Ethernet Media Access Controller EMAC For the memory address of these registers see the TMS320TCI6486 Communications Infrastructure Digital Signal EMAC Port Registers Processor data manual SPRS300 or the 7MS320C6472 Fixed Point Digital Signal Processor data manual SPRS612 Table 36 Ethernet Media Access Controller EMAC Registers Offset Acronym Register Description See Oh TXIDVER Transmit Identification and Version Register Section 5 1 4h TXCONTROL Transmit Control Register Section 5 2 8h TXTEARDOWN Transmit Teardown Register Section 5 3 10h RXIDVER Receive Identification and Version Register Section 5 4 14h RXCONTROL Rec
156. gical components e MDIO clock generator e Global PHY detection and link state monitoring e Active PHY monitoring e PHY register user access SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 47 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Functional Architecture www ti com Figure 21 MDIO Module Block Diagram Peripheral clock MDIO clock generator MDIO MDCLK USERINT interface E MDIO EMIC module LINKINT PHY monitoring Control Configuration bus registers and logic 2 8 1 1 MDIO Clock Generator The MDIO clock generator controls the MDIO clock based on a divide down of the peripheral clock CPUCLK 6 The MDIO clock is specified to run up to 2 5 MHz although typical operation would be 1 0 MHz As the peripheral clock frequency is variable CPUclk 6 the application software or driver controls the divide down amount 2 8 1 2 Global PHY Detection and Link State Monitoring The MDIO module enumerates all PHY devices in the system by continuously polling all 32 MDIO addresses The module tracks whether a PHY on a particular address has responded and whether the PHY currently has a link This information allows the software application to quickly determine which MDIO address the PHY is using and if the system is using more than one PHY The software application can then quickly switch between PHYs based on their current lin
157. gister USERINTMASKED Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 0 USERINTMASKED Masked value of MDIO User command complete interrupt When asserted a bit indicates that the previously scheduled PHY read or write command using that particular USERACCESS register has completed and the corresponding USERINTMASKSET bit is set to 1 Writing a 1 will clear the interrupt and writing 0 has no effect SPRUEF8F March 2006 Revised November 2010 84 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 10 MDIO User Command Complete Interrupt Mask Set Register USERINTMASKSET The MDIO user command complete interrupt mask set register USERINTMASKSET is shown in Figure 37 and described in Table 30 Figure 37 MDIO User Command Complete Interrupt Mask Set Register USERINTMASKSET 31 16 Reserved HO 15 2 1 0 Reserved KE HO R WC 0 LEGEND R Read only R WC Read Write 1 to clear n value after reset Table 30 MDIO User Command Complete Interrupt Mask Set Register USERINTMASKSET Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 0 USERINTMASKSET MDIO user interrupt mask set for USERINTMASKED 1 0 respectively Setting a bit to 1 will enable MDIO user command complete interrupts for that partic
158. han 64 bytes long e Hada CRC error alignment error or code error e Was not the result of a collision caused by half duplex collision based flow control See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic 150 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 50 11 Filtered Receive Frames Register RXFILTERED The total number of frames received on the EMAC that the EMAC address matching process indicated should be discarded Such a frame is defined as having all of the following e Was any data frame not MAC control frame destined for any unicast broadcast or multicast address e Did not experience any CRC error alignment error code error e The address matching process decided that the frame should be discarded filtered because it did not match the unicast broadcast or multicast address and it did not match due to promiscuous mode To determine the number of receive frames discarded by the EMAC for any reason sum the following statistics promiscuous mode disabled e Receive fragments e Receive undersized frames e Receive CRC errors e Receive alignment code errors e Receive jabbers e Receive overruns e Receive filtered frames This may not be an exact count because the receive overruns statist
159. he RXMBPENABLE register 2 5 5 13 Oversize Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet is an oversized frame and was not discarded because the RXCEFEN bit was set in the RXMBPENABLE register 2 5 5 14 Fragment Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet is only a packet fragment and was not discarded because the RXCEFEN bit was set in the RXMBPENABLE register 2 5 5 15 Undersized Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet is undersized and was not discarded because the RXCSFEN bit was set in the RXMBPENABLE register SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 39 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 5 5 16 Control Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet is an EMAC control frame and was not discarded because the RXCMFEN bit was set in the RXMBPENABLE register 2 5 5 17 Overrun Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet was aborted due to a receive overrun 2 5 5 18 Code Error CODEERROR Flag The EMAC sets this flag in the SOP buffer descriptor if the received packet contained a code error and was not discarded because the RXCEFEN bit was set in the RXMBPENABLE register 2 5 5 19 Alignment Error A
160. he corresponding alive bit to be updated The alive bits are only meant to be used to give an indication of the presence or not of a PHY with the corresponding address Writing a 1 to any bit will clear it writing a 0 has no effect 0 The PHY fails to acknowledge the access The most recent access to the PHY with an address corresponding to the register bit number was acknowledged by the PHY SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 79 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS MDIO Registers www ti com 4 5 PHY Link Status Register LINK The PHY link status register LINK is shown in Figure 32 and described in Table 25 Figure 32 PHY Link Status Register LINK 31 16 LINK R 0 15 0 LINK R 0 LEGEND R Read only n value after reset Table 25 PHY Link Status Register LINK Field Descriptions Bit Field Value Description 31 0 LINK MDIO Link state bits This register is updated after a read of the Generic Status Register of a PHY The bit is set if the PHY with the corresponding address has link and the PHY acknowledges the read transaction The bit is reset if the PHY indicates it does not have a link or fails to acknowledge the read transaction Writes to the register have no effect The PHY indicates it does not have a link or fails to acknowledge the re
161. ia Access Controller EMAC Registers ecceeeeeeeee eens eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaees 91 37 Transmit Identification and Version Register TXIDVER Field Descriptions sssssssssssssesrrrnrrrrerrrene 95 38 Transmit Control Register TXCONTROL Field Descrpttons seen ee eeeeeeeeeeeeeeeeeeeeeaeeee 96 39 Transmit Teardown Register TXTEARDOWN Field Description 97 40 Receive Identification and Version Register RXIDVER Field Descriptions E 98 41 Receive Control Register RXCONTROL Field Descriptions sssssssssrerrrrrrnnnnnnnnrnnnnnnnnnnnnnnnnnnn 99 42 Receive Teardown Register RXTEARDOWN Field Descriptons 100 43 Transmit Interrupt Status Unmasked Register TXINTSTATRAW Field Descriptions eeeeeeeees 101 44 Transmit Interrupt Status Masked Register TXINTSTATMASKED Field Descriptions ssseccccscceenns 102 45 Transmit Interrupt Mask Set Register TXINTMASKSET Field Descripttons 103 46 Transmit Interrupt Mask Clear Register TXINTMASKCLEAR Field Descriptions ecseeeeeeeeeeeees 104 List of Tables SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 47 MAC Input Vector Register MACINVECTOR Field Descriptions cceeeeeee sees teens eeeeeeeeeeeeeeeeeee 105 48 MAC End of Interrupt Vector Register MACEOIVECTOR Field Descripitons s s sssssssssssrrnrrnnnrsssnne 106
162. ic is independent of the other statistics so if an overrun occurs at the same time as one of the other discard reasons then the above sum double counts that frame 5 50 12 Receive QOS Filtered Frames Register RXQOSFILTERED The total number of frames received on the EMAC that were filtered due to receive quality of service QOS filtering Such a frame is defined as having all of the following e Any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e The frame destination channel flow control threshold register RXnNFLOWTHRESH value was greater than or equal to the channel s corresponding free buffer register RXnFREEBUFFER value e Was of length 64 to RXMAXLEN e RXQOSEN bit is set in RXMBPENABLE e Had no CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic 5 50 13 Receive Octet Frames Register RXOCTETS The total number of bytes in all good frames received on the EMAC A good frame is defined as having all of the following e Any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of length 64 to RXMAXLEN bytes inclusive e Had no CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic 5 50 14 Go
163. icnnennendrenesiententieieinicincsiece SEENEN a eege eeben 58 2 12 Packet Transmit Operation Zeg ines Au bee geed ees Ge ee E ENEE A 62 2 13 Receive and Transmit Latency E 63 2 14 Tramster Node Priority eiis g eege ENEE EE ENEE 63 2 15 Reset Considerations ue ee ee 64 ALE 65 2 07 Interrupt SUPPOR E 67 2 18 Power Management EE 69 2 19 Emulation Considerations ube sue eE ene ES EEGENEN NEES 69 3 EMIC Module E UE TE 71 3 1 EW INTC TE EE d 3 2 RPIC Registers eet siereeugeregetere g e RENE E a euee 71 3 3 PIG TE EE 74 3 4 Prescalar Configuration Register PSCFG ae 75 4 MDIO ge ET sennsnionnpiead aE EE a E E a aE a aaa 76 4 1 ite ele TEE 76 4 2 MDIO Version Register VERSION ENEE Jr 4 3 MDIO Control Register CONTROL staresina SE AE EES dE Ee 78 4 4 PHY Acknowledge Status Register ALIVE ua 79 4 5 PAX Link Statuis Register LINK Zeg ecicis acca andes is cit anette araeiuiainn unio eislrarersetareine women EOR 80 4 6 MDIO Link Status Change Interrupt Unmasked Register LINKINTRAW A 81 4 7 MDIO Link Status Change Interrupt Masked Register LINKINTMASKED ssassssssssssssnsnnnnnerrseseenns 82 4 8 MDIO User Command Complete Interrupt Unmasked Register USERINTRAW eeeeeeeeeeeeeeee 83 4 9 MDIO User Command Complete Interrupt Masked Register USERINTMASKED nssssssssssssssrssssseee 84 4 10 MDIO User Command Complete Interrupt Mask Set Register USERINTMASKSET an 85 SPRUEF8F March 2006 Revised November 2010 Table of
164. in Figure 30 and described in Table 23 Figure 30 MDIO Control Register CONTROL 31 30 29 28 24 23 21 20 19 18 17 16 IDLE ENABLE Reserved HIGHEST USER CHANNEL Reserved PREAMBLE FAULT Te Reserved R 1 R W 0 HO R 1 HO R W 0 R WC 0 R W 0 HO 15 0 CLKDIV R W 255 LEGEND R W Read Write R Read only n value after reset Table 23 MDIO Control Register CONTROL Field Descriptions Bit Field Value Description 31 IDLE State machine IDLE status bit 0 State machine is not in idle state State machine is in idle state 30 ENABLE State machine enable control bit If the MDIO state machine is active at the time it is 0 Disables the MDIO state machine Enable the MDIO state machine disabled it will complete the current operation before halting and setting the idle bit 29 Reserved 0 Reserved 28 24 HIGHEST _USER_CHANNEL Highest user channel that is available in the module It is currently set to 1 This implies that MDIOUserAccess1 is the highest available user access channel 23 21 Reserved 0 Reserved 20 PREAMBLE Preamble disable 0 Standard MDIO preamble is used Disables this device from sending MDIO frame preambles 19 FAULT Fault indicator This bit is set to 1 if the MDIO pins fail to read back what the device is driving onto them This indicates a physical layer fault and the module state machine is reset Writing a 1 to it clears this bit 0 No failure Physical layer fault the MDIO state machine is reset
165. interrupts are disabled Link change status interrupts for PHY address specified in PHYADDRMON bits are enabled 5 Reserved 0 Reserved 4 0 PHYADRMON PHY address whose link status is to be monitored 88 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 14 MDIO User Access Register 1 USERACCESS1 The MDIO user access register 1 USERACCESS1 is shown in Figure 41 and described in Table 34 Figure 41 MDIO User Access Register 1 USERACCESS1 31 30 29 28 oe 25 ou 20 16 GO WRITE ACK Reserved REGADR PHYADR R WS 0 R W 0 DW R 0 R W 0 R W 0 15 0 DATA R W 0 LEGEND R Read only R W Read Write R WS Read Write 1 to set n value after reset Table 34 MDIO User Access Register 1 USERACCESS1 Field Descriptions Bit Field Value Description 31 GO Go bit Writing a 1 to this bit causes the MDIO state machine to perform an MDIO access when it is convenient for it to do so this is not an instantaneous process Writing a 0 to this bit has no effect This bit is write able only if the MDIO state machine is enabled This bit will self clear when the requested access has been completed Any writes to the USERACCESSO register are blocked when the go bit is 1 30 WRITE Write enable bit Setting this bit to a 1 causes the MDIO transaction
166. ion Frames Register Section 5 50 22 258h TXLATECOLL Transmit Late Collision Frames Register Section 5 50 23 25Ch TXUNDERRUN Transmit Underrun Error Register Section 5 50 24 260h TXCARRIERSENSE Transmit Carrier Sense Errors Register Section 5 50 25 264h TXOCTETS Transmit Octet Frames Register Section 5 50 26 268h FRAME64 Transmit and Receive 64 Octet Frames Register Section 5 50 27 26Ch FRAME651127 Transmit and Receive 65 to 127 Octet Frames Register Section 5 50 28 270h FRAME128T255 Transmit and Receive 128 to 255 Octet Frames Register Section 5 50 29 274h FRAME256T511 Transmit and Receive 256 to 511 Octet Frames Register Section 5 50 30 278h FRAME512T1023 Transmit and Receive 512 to 1023 Octet Frames Register Section 5 50 31 SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 93 Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com Table 36 Ethernet Media Access Controller EMAC Registers continued Offset Acronym Register Description See 27Ch FRAME1024TUP Transmit and Receive 1024 to RXMAXLEN Octet Frames Section 5 50 32 Register 280h NETOCTETS Network Octet Frames Register Section 5 50 33 284h RXSOFOVERRUNS Receive FIFO or DMA Start of Frame Overruns Register Section 5 50 34 288h RXMOFOVERRUNS Receive FIFO or DMA Middle of Frame Overruns Register Section 5 50 35 28Ch RXDMAOVERRUNS Receive DMA Start of Frame and Midd
167. is bit should be cleared to zero for unused address RAM locations 0 Address location is not valid and will not be used in determining whether or not an incoming packet matches or is filtered 1 Address location is valid and will be used in determining whether or not an incoming packet matches or is filtered 19 MATCHFILT Match or filter bit 0 The address will be used if VALID is set to determine if the incoming packet address should be filtered 1 The address will be used if VALID is set to determine if the incoming packet address is a match 18 16 CHANNEL Channel bit determines which receive channel a valid address match will be transferred to The channel is a don t care if the MATCHFILT bit is cleared to zero 15 8 MACADDRO MAC address lower 8 bits byte 0 7 0 MACADDRI1 MAC address bits 15 8 byte 1 SPRUEF8F March 2006 Revised November 2010 C6472 TC1I6486 EMAC MDIO 141 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 44 MAC Address High Bytes Register MACADDRHI The MAC address high bytes register MACADDRHI is shown in Figure 86 and described in Table 80 Figure 86 MAC Address High Bytes Register MACADDRHI 31 24 23 16 MACADDR2 MACADDR3 R W 0 R W 0 15 8 7 0 MACADDR4 MACADDR5 R W 0 R W 0 LEGEND R W Read Write n value after reset Table 80 MAC Address High Bytes Register MACADDRHI Field
168. is defined as having all of the following e Any data or MAC control frame that matched a unicast broadcast or multicast address or matched due to promiscuous mode e Was of length 64 to RXMAXLEN bytes inclusive e Had no CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic Broadcast Receive Frames Register RXBCASTFRAMES The total number of good broadcast frames received on the EMAC A good broadcast frame is defined as having all of the following e Any data or MAC control frame that was destined for address FF FF FF FF FF FFh only e Was of length 64 to RXMAXLEN bytes inclusive e Had no CRC error alignment error or code error See Section 2 5 5 for definitions of alignment code and CRC errors Overruns have no effect on this statistic C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 50 3 Multicast Receive Frames Register RXMCASTFRAMES The total number of good multicast frames received on the EMAC A good multicast frame is defined as having all of the following e Any data or MAC control frame that was destined for any multicast address other than FF FF FF FF FF FFh e Was of length 64 to RXMAXLEN bytes inclusive e Had no CRC error alignment error or code error
169. it and receive operations and buffer descriptors are covered in Section 2 5 2 7 Ethernet Multicore Interrupt Combiner EMIC Module The ethernet multicore interrupt combiner EMIC module is designed to efficiently route a single set of interrupts from EMAC and MDIO to multiple cores on a multicore device It also incorporates interrupt pacing functionality for the Ethernet TX and RX pulse interrupts The EMIC module uses the pulse interrupts to incorporate some of its pacing functionality A high level block diagram of the EMIC is shown in Figure 14 The following components as shown in Figure 14 make up the EMIC e Pacer Block which consists of Timed Delay state machine TSM Divide State Machine DSM e Transmit Pacer and Interrupt Combiner TPIC which consists of Pacer block per TX event Interrupt combiner e Receive Pacer and Interrupt Combiner RPIC which consists of Pacer block per TX event 40 C6472 TC16486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture Interrupt combiner e Common Interrupt Combiner CIC e Prescaler e Registers e CFG peripheral bus interface Figure 14 EMIC Block Diagram MACRXINTO gt To GEMO interrupts 18 MACTXINT1 7 MACRXINT1 gt To GEM interrupts 2 MACRXINT2 gt To GEM2 Peripheral bus MACRXINT3 gt T
170. ive group is asserted by EMAC Figure 23 EW_INTCTL Register 31 24 Reserved 0000 0000 23 22 21 20 19 18 17 16 RX7 RX6 RX5 RX4 RX3 RX2 SEA RX0O R W 0 R W 0 R W 0 R W 0 R W 0 R W 0 R W 0 R W 0 15 14 13 12 11 10 9 8 TX7 TX6 TX5 TX4 TX3 TX2 TX1 TXO R W 0 R W 0 R W 0 R W 0 R W 0 R W 0 R W 0 R W 0 7 5 4 3 2 1 0 Reserved MDIO_USER MDIO_LINT STAT HOST Reserved 000 R W 0 R W 0 R W 0 R W 0 0 LEGEND R W Read Write R Read only n value after reset 3 2 RPIC Registers 3 2 1 RPCFG Registers There are eight RPCFG registers RPCFGO through RPCFG7 one per receive event This register configuration is common to all C64x megamodules The RPCFG register details are shown in Figure 24 and described in Table 17 SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMIC Module Registers IA TEXAS INSTRUMENTS EMIC Module Registers www ti com Figure 24 RPCFG Register 31 28 27 16 Reserved TIME_CFG 0000 R W 0000 0000 15 8 7 4 3 2 1 0 CNT_CFG Reserved TU CU TR CR R W 0000 0000 0000 R W 0 R W 0 R W 0 R W 0 LEGEND R W Read Write R Read only n value after reset Table 17 RPCFG Register Field Descriptions Bit Field Value Description 31 28 Reserved Reserved 27 16
171. ively supports an additional two interfaces standard media independent interface MII and standard gigabit media independent interface GMIII e EMAC acts as DMA master to either internal or external device memory space e Eight receive channels with VLAN tag discrimination for receive quality of service QOS support e Eight transmit channels with round robin or fixed priority for transmit quality of service QOS support e Ether stats and 802 3 stats statistics gathering e Transmit CRC generation selectable on a per channel basis e Broadcast frames selection for reception on a single channel e Multicast frames selection for reception on a single channel e Promiscuous receive mode frames selection for reception on a single channel all frames all good frames short frames error frames e Hardware flow control e CPPI 3 0 compliant e Tl adaptive performance optimization for improved half duplex performance e Ethernet Multicore Interrupt Combiner EMIC for EMAC and MDIO interrupts e Programmable interrupt logic permits the software driver to restrict the generation of back to back interrupts thus allowing more work to be performed in a single call to the interrupt service routine SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 11 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated Introduction Single MDIO shared by both EMAC modules 1 3 Functional Block Di
172. k status 2 8 1 3 Active PHY Monitoring Once a PHY candidate has been selected for use the MDIO module transparently monitors its link state by reading the PHY status register The MDIO device stores link change events that may optionally interrupt the CPU Thus the system can poll the link status of the PHY device without continuously performing MDIO accesses Up to two PHY devices can be actively monitored at any given time 2 8 1 4 PHY Register User Access When the DSP must access the MDIO for configuration and negotiation the PHY access module performs the actual MDIO read or write operation independent of the CPU Thus the CPU can poll for completion or receive an interrupt when the read or write operation has been performed There are two user access registers USERACCESSO and USERACCESS1 allowing the software to submit up to two access requests simultaneously The requests are processed sequentially 48 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 8 2 MDIO Module Operational Overview The MDIO module implements the 802 3 serial management interface to simultaneously interrogate and control up to two Ethernet PHYs using a shared two wired bus It separately performs auto detection and records the current link status of up to 32 PHYs polling all 32 MDIO
173. le of Frame Overruns Section 5 50 36 Register 94 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 5 1 Transmit Identification and Version Register TXIDVER The transmit identification and version register TXIDVER is shown in Figure 43 and described in EMAC Port Registers Table 37 Figure 43 Transmit Identification and Version Register TXIDVER 31 16 TXIDENT 0x000C 15 11 10 8 7 0 RTLVER TXMAJORVER TXMINORVER 0x01 0x02 0x08 LEGEND R Read only n value after reset Table 37 Transmit Identification and Version Register TXIDVER Field Descriptions Bit Field Value Description 31 16 TXIDENT Transmit identification value 15 11 RTLVER RTL version value 10 8 TXMAJORVER Transmit major version value 7 0 TXMINORVER Transmit minor version value SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated C6472 TCI6486 EMAC MDIO 95 I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 2 Transmit Control Register TXCONTROL The transmit control register TXCONTROL is shown in Figure 44 and described in Table 38 Figure 44 Transmit Control Register TXCONTROL 31 16 Reserved HO 15 1 0 Reserved TXEN R 0
174. lue is set 2 17 1 4 Host Error Interrupt The host error interrupt HOSTPEND is issued if enabled under error conditions due to the handling of buffer descriptors detected during transmit or receive DMA transactions The failure of the software application to supply properly formatted buffer descriptors results in this error The error bit can only be cleared by resetting the EMAC module in hardware The host error interrupt is enabled by setting the HOSTMASK bit in the MACINTMASKSET register The host error interrupt is disabled by clearing the appropriate bit in the MACINTMASKCLEAR register The raw and masked host error interrupt status may be read by reading the MACINTSTATRAW and MACINTSTATMASKED registers respectively Transmit host error conditions include e SOP error e Ownership bit not set in SOP buffer e Zero next buffer descriptor pointer without EOP e Zero buffer pointer e Zero buffer length e Packet length error Receive host error conditions include e Ownership bit not set in input buffer e Zero buffer pointer 2 17 2 MDIO Module Interrupt Events and Requests The MDIO module generates two interrupt events as follows e LINKINT Serial interface link change interrupt Indicates a change in the state of the PHY link e USERINT Serial interface user command event complete interrupt 68 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texa
175. mes 7h Select channel 7 to receive promiscuous frames 15 14 Reserved 0 Reserved 13 RXBROADEN Receive broadcast enable Enable received broadcast frames to be copied to the channel selected by RXBROADCH bits 0 Broadcast frames are filtered 1 Broadcast frames are copied to the channel selected by RXBROADCH bits 12 11 Reserved 0 Reserved 10 8 RXBROADCH 0 3h Receive broadcast channel select 0 Select channel 0 to receive broadcast frames th Select channel 1 to receive broadcast frames 2h Select channel 2 to receive broadcast frames 3h Select channel 3 to receive broadcast frames 4h Select channel 4 to receive broadcast frames 5h Select channel 5 to receive broadcast frames 6h Select channel 6 to receive broadcast frames 7h Select channel 7 to receive broadcast frames 7 6 Reserved 0 Reserved 5 RXMULTEN RX multicast enable Enable received hash matching multicast frames to be copied to the channel selected by RXMULTCH bits 0 Multicast frames are filtered 1 Multicast frames are copied to the channel selected by RXMULTCH bits 4 3 Reserved 0 Reserved 116 C6472 TC1I6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Table 57 Receive Multicast Broadcast Promiscuous Channel Enable Register RXMBPENABLE Field Descriptions continued EMAC Port Registers Bit Field Value Description 2 0
176. mit Channel 5 Completion Pointer Interrupt Section 5 48 Acknowledge Register 658h TX6CP Transmit Channel 6 Completion Pointer Interrupt Section 5 48 Acknowledge Register 92 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers Table 36 Ethernet Media Access Controller EMAC Registers continued Offset Acronym Register Description See 65Ch TX7CP Transmit Channel 7 Completion Pointer Interrupt Section 5 48 Acknowledge Register 660h RXOCP Receive Channel 0 Completion Pointer Interrupt Section 5 49 Acknowledge Register 664h RX1CP Receive Channel 1 Completion Pointer Interrupt Section 5 49 Acknowledge Register 668h RX2CP Receive Channel 2 Completion Pointer Interrupt Section 5 49 Acknowledge Register 66Ch RX3CP Receive Channel 3 Completion Pointer Interrupt Section 5 49 Acknowledge Register 670h RX4CP Receive Channel 4 Completion Pointer Interrupt Section 5 49 Acknowledge Register 674h RX5CP Receive Channel 5 Completion Pointer Interrupt Section 5 49 Acknowledge Register 678h RX6CP Receive Channel 6 Completion Pointer Interrupt Section 5 49 Acknowledge Register 67Ch RX7CP Receive Channel 7 Completion Pointer Interrupt Section 5 49 Acknowledge Register Network Statistics Registers 200h RXGOODFRAMES Good Receive Frames Section 5 50 1 204h RXBCASTFRAMES
177. n 4 125 MHz 125 MHz used for GMI SYSCLK15 100 5 MHz Used for RGMIIO only SYSCLK16 2 250 MHz Used for RGMII1 only SYSCLK17 10 50 MHz Used for RGMII1 default SYSCLK18 100 5 MHz Used for RGMII1 only 2 1 1 MII Clocking The Mil interface is supported by EMACO only When MACSELO is set to zero 000b the transmit and receive clock sources are provided from an external PHY via the MTCLK and MRCLK pins These clocks are inputs to the EMAC module and operate at 2 5 MHz in 10 Mbps mode and at 25 MHz in 100 MHz mode The MII clocking interface is not used in 1000 Mbps mode For timing purposes data is transmitted and received with reference to MTCLK and MRCLK respectively 2 1 2 RMII Clocking The RMII interface is selected when MACSELO is set to 1 001b or MACSEL1 is set to 3 11b RMII requires two clock sources the peripheral bus clock and the reference clock REF_CLKk input to the RMII gasket A 50 MHz clock from device input pin REFCLKx is supplied to the REF_CLK input of the RMII gasket The EMAC clocks the transmit and receive operations from the reference clock The MTCLK and MRCLK device pins are not used for this interface The RMII protocol turns one data phase of an MII transfer into two data phases at double the clock frequency This is the driving factor for the 50 MHz reference clock Data at the I O pins are running at 5 MHz in 10 Mbps mode and at 50 MHz in 100 Mbps mode SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC
178. n history highlights the technical changes made to the document in this revision Table 87 EMAC MDIO Revision History See Additions Modifications Deletions Figure 52 Modified TXINTMASKCLEAR register figure Table 46 Modified TXINTMASKCLEAR register table Figure 57 Modified RXINTMASKSET register figure Table 51 Modified RXINTMASKSET register table Figure 58 Modified RXINTMASKCLEAR register figure Table 52 Modified RXINTMASKCLEAR register table SPRUEF8F March 2006 Revised November 2010 Revision History 159 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries Tl reserve the right to make corrections modifications enhancements improvements and other changes to its products and services at any time and to discontinue any product or service without notice Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete All products are sold subject to Tl s terms and conditions of sale supplied at the time of order acknowledgment TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Tl s standard warranty Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty Except where mandated by government requirements testing
179. nagement Data Input Output MDIO module integrated with TMS320TCI6486 TMS320C6472 devices Included are the features of the EMAC and MDIO modules a discussion of their architecture and operation how these modules connect to the outside world and the registers descriptions for each module The EMAC controls the flow of packet data from the processor to the PHY The MDIO module controls PHY configuration and status monitoring Both the EMAC and the MDIO modules interface to the DSP through EMIC modules and CPPI buffer managers that allow efficient data transmission and reception These two modules are considered integral to the EMAC MDIO peripheral 1 1 Purpose of the Peripheral The EMAC module is used on TMS320TCI6486 TMS320C6472 devices to move data between the device and another host connected to the same network in compliance with the Ethernet protocol 1 2 Features Two EMAC modules are integrated with the TCl6486 C6472 device The basic feature set of the integrated EMAC modules is e Synchronous 10 100 1000 Mbps operation e Full duplex Gigabit operation half duplex gigabit is not supported e Little endian and big endian support e Both EMAC modules support three types of interfaces to the physical layer device PHY reduced pin count media independent interface RMII reduced pin count gigabit media independent interface RGMII and source synchronous serial independent interface S3MIl e In addition to above four EMACO nat
180. ng except the data bit cycles when the pin acts as an input for read operations The TCl6486 C6472 device S3MIl pins are multiplexed with other non RGMII pins When using the S3MII0 port on EMACO there are no restrictions on the available EMAC1 Ethernet interfaces RMII1 S3MII1 and RGMII1 are useable When using the S3MII1 port on EMAC1 the EMACO Ethernet interfaces not available due to pin multiplexing are GMIIO MIIO0 The RMIIO S3MIIO and RGMIIO ports are available on EMACO Ethernet interfaces In a multi PHY situation where PHY has only one TX_SYNC for all ports external logic is needed to synchronize the TX_SYNC signals from multiple ports or TCI6486 C6472 devices The TXD signal from the multiple ports should also be synchronized using external logic since the clock phase relation of different TC16486 C6472 devices can be different Figure 7 demonstrates the example mutli PHY configuration for S3MIl C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Device 1 TXD TX_SYNC TX_CLK RXD RX_SYNC RX_CLK MHZ_125_CLK Device 2 TXD TX_SYNC TX_CLK RXD RX_SYNC RX_CLK MHZ_125_CLK Device n TXD TX_SYNC TX_CLK RXD RX_SYNC RX_CLK MHZ_125_CLK 125 MHz zero delay clock buffer Figure 7 S3MII Multi PHY Configuration
181. ng of start of frame read write indication PHY address register address and data bit cycles The MDIO pin acts as an output for everything except the data bit cycles when the pin acts as an input for read operations When the TCI6486 C6472 device is interfaced to an Ethernet switch via the GMIl interface the carrier sense MCRS and collision MCOL signals are not necessary since full duplex operation is forced On the device the GMII Ethernet interface is available only on EMACO of the device GMIIO pins are multiplexed with other non RGMII pins RMII1 S3MII1 Due to this multiplexing when the MIIO interface is selected on EMACO except for RGMII1 no Ethernet interface is available on EMAC1 2 3 4 Reduced Gigabit Media Independent Interface RGMII Connections Figure 5 shows a TCI6486 C6472 device with integrated EMAC and MDIO interfaced to the PHY via an RGMII connection This interface is available in 10 Mbps 100 Mbps and 1000 Mbps modes 22 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture Figure 5 Ethernet Configuration with RGMII Interface RGTXC RGTXD 3 0 2 5 MHz RGTXCTL 25 MHz or 125 MHz RGREFCLK Physical RGRXC layer device Transformer RGRXDJ3 0 PHY RGRXCTL RGMDCLK RGMDIO The RGMII interface is a r
182. ns do not affect the recording of frames in this Statistic C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 50 30 Transmit and Receive 256 to 511 Octet Frames Register FRAME256T511 The total number of 256 byte to 511 byte frames received and transmitted on the EMAC Such a frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Did not experience late collisions excessive collisions underrun or carrier sense error e Was 256 bytes to 511 bytes long CRC errors alignment code errors underruns and overruns do not affect the recording of frames in this statistic 5 50 31 Transmit and Receive 512 to 1023 Octet Frames Register FRAME512T1023 The total number of 512 byte to 1023 byte frames received and transmitted on the EMAC Such a frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Did not experience late collisions excessive collisions underrun or carrier sense error e Was 512 bytes to 1023 bytes long CRC errors alignment code errors and overruns do not affect the recording of frames in this statistic 5 50 32 Transmit and Receive 1024 to RXMAXLEN Octet Frames Register FRAME10
183. nsibility of the software to verify that there are no pending frames to be transferred After writing a one to this bit it may be polled to determine if the reset has occurred A value of one indicates that the reset has not yet occurred A value of zero indicates that a reset has occurred After a software reset operation all the EMAC registers need to be re initialized for proper data transmission Unlike the EMAC module the MDIO EMIC modules and CPPI buffer managers cannot be placed in reset from a register inside their memory map Hardware Reset Considerations When a hardware reset occurs the EMAC peripheral will have its register values reset and all the sub modules will return to their default state After the hardware reset the EMAC needs to be initialized before resuming its data transmission as described in Section 2 16 A hardware reset is the only means of recovering from the error interrupts HOSTPEND which are triggered by errors in packet buffer descriptors Before doing a hardware reset you should inspect the error codes in the MACSTATUS register This register provides information about the software error type that needs correction For more information on error interrupts see Section 2 17 1 4 RGMII Transmission On device reset packet transmissions on the RGMII interface are precluded for 4096 transmit clock cycles after the RGMII link signal goes high Transmission can be started only after 4096 cycles of transmi
184. ntegrated with the TC16486 C6472 device does not use the transmit coding error signal MTXER Instead of driving the error pin when an underflow condition occurs on a transmitted frame the EMAC intentionally generates an incorrect check sum by inverting the frame CRC so that the network detects the transmitted frame as an error 14 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 EMAC Functional Architecture This section discusses the architecture and basic function of the EMAC peripheral 2 1 Clock Control The frequencies for the transmit and receive clocks are fixed by the IEEE 802 3 specification as shown below s 2 5 MHz at 10 Mbps e 25 MHz at 100 Mbps e 125 MHz at 1000 Mbps All clock sources with the exception of the EMAC peripheral bus clock are sourced from the PLL2 controller The PLL2 controller has 3 clocks for EMACO SYSCLK13 SYSCLK14 and SYSCLK15 For EMACO operation the SYSCLK14 divider is programmable and other clocks are fixed The PLL multiplier value of the PLL2 controller is also fixed The PLL2 controller has 3 clocks for EMAC1 SYSCLK16 SYSCLK17 and SYSCLK18 These clocks should remain fixed Table 3 EMAC Clock Specifications Clock Divider Frequency Purpose SYSCLK13 2 250 MHz Used for RGMIIO only 10 or 50 or 50 MHz used for RGMII default Ser
185. ntinuous clock that provides the timing reference for transmit operations The TXD and TX_SYNC signals are tied to this clock This clock is 125 MHz at 10 and 100 Mbps operations TX_SYNC O Transmit Synchronization The TX_SYNC signal is used to synchronize the TXD data signal This signal is synchronized with a 125 MHz clock TXD O Transmit Data The transmit data is synchronized with a transmit clock and a transmit synchronization signal RX_CLK l Transmit clock The transmit clock is a continuous clock that provides the timing reference for transmit operations The RXD and RX_SYNC signals are tied to this clock This clock is 125 MHz at 10 and 100 Mbps operations RX_SYNC l Receive Synchronization The RX_SYNC signal is used to synchronize the RXD data signal This signal is synchronized with a 125 MHz clock RXD l Receive Data The receive data is synchronized with a receive clock and a receive synchronization signal MDCLK O Management data clock MDCLK The MDIO data clock is sourced by the MDIO module It synchronizes MDIO data access operations done on the MDIO pin The frequency of this clock is controlled by the CLKDIV bits in the MDIO control register CONTROL MDIO UO Management data input output MDIO The MDIO pin drives PHY management data into and out of the PHY via an access frame consisting of start of frame read write indication PHY address register address and data bit cycles The MDIO pin acts as an output for everythi
186. nts receive statistics The EMAC module operates independently of the CPU It is configured and controlled by its register set mapped into device memory Information about data packets is communicated using 16 byte descriptors For transmit operations each 16 byte descriptor describes a packet or packet fragment in the system s internal or external memory For receive operations each 16 byte descriptor represents a free packet buffer or buffer fragment On both transmit and receive an Ethernet packet is allowed to span one or more memory fragments represented by one 16 byte descriptor per fragment In typical operation there is only one descriptor per receive buffer but transmit packets may be fragmented depending on the software architecture SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 53 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 10 2 10 1 An interrupt is issued to the CPU whenever a transmit or receive operation has completed However it is not necessary for the CPU to service the interrupt while there are additional resources available In other words the EMAC continues to receive Ethernet packets until its receive descriptor list has been exhausted On transmit operations the transmit descriptors need only be serviced to recover their associated memory buffer Thus it is possible to delay servi
187. o GEM3 MACRXINT4 gt To GEM4 Peripheral bus EE J MACRXINT5 gt To GEM5 PS_TICK Peripheral bus SPRUEF8F March 2006 Revised November 200 C6A72 TCI6486 EMACMDIO A Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 7 1 42 Pacing Block In simple terms interrupt pacing represents delaying the initial EMAC events to CPU interrupt based on certain criteria The pacing block is the basic building block for the interrupt pacing operation One of the motivations for interrupt pacing is that during Ethernet operation hundreds or thousands of interrupts are generated per second for packets transmitted or received and interrupt pacing relieves the CPU of the burden of processing every single interrupt This block provides time based or count based pacing of interrupts in any combination In addition this block supports reprogramming of timer value and count value without hardware software race condition and also facilitates use of the same timer and count values for the next event period The EVT_IN is the pulse interrupt from EMAC This is forwarded to timed delay and divide by N state machines see Figure 15 The state machine outputs are combined and sent out as EVT_OUT PS_TICK is the clock tick from the prescalar block The prescaler block forwards this signal to all the pacing blocks Figure 15 Pacing Block Pacing block PS_TIC
188. o disabled unicast multicast or broadcast channels are considered non address matching MAC control frames address match only if the RXCMFEN bit is set RXCEFEN and RXCSFEN determine whether error frames are transferred to memory or not but they do not determine whether error frames are address matching or not Short frames are a special type of error frames A single channel is selected as the promiscuous channel by the RXKPROMCH field in the RXMBPENABLE register The promiscuous receive mode is enabled by the RXCMFEN RXCEFEN RXCSFEN and RXCAFEN bits in RXMBPENABLE Table 14 shows the effects of the promiscuous enable bits Proper frames are frames that are between 64 and RXMAXLEN bytes in length inclusive and contain no code align or CRC errors Table 14 Receive Frame Treatment Summary Address RXMBPENABLE Bits Match RXCAFEN RXCEFEN RXCMFEN RXCSFEN Frame Treatment 0 0 X X X No frames transferred 0 1 0 0 0 Proper frames transferred to promiscuous channel 0 1 0 0 1 Proper undersized data frames transferred to promiscuous channel 0 1 0 1 0 Proper data and control frames transferred to promiscuous channel 0 1 0 1 1 Proper undersized data and control frames transferred to promiscuous channel 0 1 1 0 0 Proper oversize jabber code align CRC data frames transferred to promiscuous channel No control or undersized fragment frames are transferred 0 1 1 0 1 Proper undersized fragment oversize jabber code align CRC da
189. ocessed by the host during interrupt processing The EMAC uses the value written to determine if the interrupt should be de asserted 146 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 49 Receive Channel 0 7 Completion Pointer Register RXnCP The receive channel 0 7 completion pointer register RXnCP is shown in Figure 91 and described in Table 85 Figure 91 Receive Channel n Completion Pointer Register RXnCP 31 16 RXnCP R W x 15 0 RXnCP R W x LEGEND R W Read Write n value after reset Table 85 Receive Channel n Completion Pointer Register RXnCP Field Descriptions Bit Field Value Description 31 0 RXnCP Receive channel n completion pointer register is written by the host with the buffer descriptor address for the last buffer processed by the host during interrupt processing The EMAC uses the value written to determine if the interrupt should be de asserted SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 147 5 50 A TEXAS INSTRUMENTS EMAC Port Registers www ti com Network Statistics Registers The EMAC has a set of statistics that record events associated with frame tr
190. od Transmit Frames Register TXGOODFRAMES The total number of good frames transmitted on the EMAC A good frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Was any length e Had no late or excessive collisions no carrier loss and no underrun SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 151 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 50 15 Broadcast Transmit Frames Register IXBCASTFRAMES The total number of good broadcast frames transmitted on the EMAC A good broadcast frame is defined as having all of the following e Any data or MAC control frame destined for address FF FF FF FF FF FFh only e Was of any length e Had no late or excessive collisions no carrier loss and no underrun 5 50 16 Multicast Transmit Frames Register TXMCASTFRAMES The total number of good multicast frames transmitted on the EMAC A good multicast frame is defined as having all of the following e Any data or MAC control frame destined for any multicast address other than FF FF FF FF FF FFh e Was of any length e Had no late or excessive collisions no carrier loss and no underrun 5 50 17 Pause Transmit Frames Register TXPAUSEFRAMES The total number of IEEE 802 3X pause frames transmitted by the EMAC Pause frames cannot underrun or c
191. of all parameters of each product is not necessarily performed TI assumes no liability for applications assistance or customer product design Customers are responsible for their products and applications using TI components To minimize the risks associated with customer products and applications customers should provide adequate design and operating safeguards TI does not warrant or represent that any license either express or implied is granted under any TI patent right copyright mask work right or other TI intellectual property right relating to any combination machine or process in which TI products or services are used Information published by TI regarding third party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof Use of such information may require a license from a third party under the patents or other intellectual property of the third party or a license from TI under the patents or other intellectual property of TI Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties conditions limitations and notices Reproduction of this information with alteration is an unfair and deceptive business practice TI is not responsible or liable for such altered documentation Information of third parties may be subject to additional restrictions Resal
192. of receive pacer and interrupt combiner RPIC RXEVT 0 RXEVT 1 RXEVT 2 RXEVT 3 RXEVT 4 RXEVT 5 RXEVT 6 RXEVTI7 Figure 19 Receive Pacer and Interrupt Combiner Pacing block gt gt gt gt gt gt Pacing block _ Pacing block Pacing block Pacing block gt PS_TICK 46 C6472 TCI6486 EMAC MDIO EW_INTCTL 16 EW_INTCTL 17 EW_INTCTL 18 EW_INTCTL 19 EW_INTCTL 20 EW_INTCTL 21 EW_INTCTL 22 EW_INTCTL 23 EW_INTCTL 23 16 Receive pacer and interrupt combiner MACRXINT SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 7 6 2 8 2 8 1 Common Interrupt Combiner CIC The common interrupt combiner CIC block performs following functions e Combines the two common interrupts from EMAC HOST and STAT with the two MDIO interrupts MDIO_LINT and MDIO_USER and generates a single MACINT interrupt per theC64x megamodule e Performs a level to pulse conversion of the interrupts because the interrupts from EMAC and MDIO are level sensitive and the C64x megamodule expects a pulse interrupt e Allows per interrupt enabling or disabling of the interrupts the setting of bits 1 to 4 in the EW_INTCTL register Figure 20 is the block diagram representing common
193. ollision SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 137 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Port Registers A TEXAS INSTRUMENTS www ti com 5 40 Transmit Pacing Algorithm Test Register TPACETEST The transmit pacing algorithm test register TRACETEST is shown in Figure 82 and described in Table 76 31 Figure 82 Transmit Pacing Algorithm Test Register TPACETEST Reserved 15 HO Reserved PACEVAL HO R 0 LEGEND R Read only n value after reset Table 76 Transmit Pacing Algorithm Test Register TPACETEST Field Descriptions Bit Field Value Description 31 5 Reserved 0 Reserved 4 0 PACEVAL Pacing register current value A nonzero value in this field indicates that transmit pacing is active A transmit frame collision or deferral causes PACEVAL to be loaded with 1Fh 31 good frame transmissions with no collisions or deferrals cause PACEVAL to be decremented down to 0 When PACEVAL is nonzero the transmitter delays four Inter Packet Gaps between new frame transmissions after each successfully transmitted frame that had no deferrals or collisions If a transmit frame is deferred or suffers a collision the IPG time is not stretched to four times the normal value Transmit pacing helps reduce capture effects which improves overall network bandwidth
194. ome inactive at a future point in time For example a PHY can have its MDIO addresses changed while the system is running although it is not a common occurrence This condition can be tested by periodically checking the PHY state in the ALIVE register Example 3 MDIO Register Access Macros define PHYREG_read regadr phyadr MDIO_REGS gt USERACCESSO CSL_FMK MDIO_USERACCESS0_GO 1u CSL_FMK MDIO_USERACCESSO_REGADR regadr CSL_FMK MDIO_USERACCESSO0_PHYADR phyadr define PHYREG_write regadr phyadr data MDIO_REGS gt USERACCESSO CSL_FMK MDIO_USERACCESS0_GO 1u CSL_FMK MDIO_USERACCESS0_WRITE 1 CSL_FMK MDIO_USERACCESSO_REGADR regadr CSL_FMK MDIO_USERACCESSO_PHYADR phyadr CSL_FMK MDIO_USERACCESSO_DATA data define PHYREG_wait while CSL_FEXT MDIO_REGS gt USERACCESS0 MDIO_USERACCESS0_GO define PHYREG_wait Results results while CSL_FEXT MDIO_REGS gt USERACCESS0 MDIO_USERACCESSO_GO results CSL_FEXT MDIO_REGS gt USERACCESS0 MDIO_USERACCESSO_DATA SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 51 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated A TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 9 EMAC Module This section discusses the architecture and basic functions of the EMAC sub module integrated with the TC1I6486 C6472 device 2 9 1 EMAC Module Comp
195. on set and interrupts for the TMS320C6000 digital signal processors DSPs SPRU198 TMS320C6000 Programmer s Guide Describes ways to optimize C and assembly code for the TMS320C6000 DSPs and includes application program examples SPRU301 TMS320C6000 Code Composer Studio Tutorial Introduces the Code Composer Studio integrated development environment and software tools SPRU321 Code Composer Studio Application Programming Interface Reference Guide Describes the Code Composer Studio application programming interface API which allows you to program custom plug ins for Code Composer SPRU871 TMS320C64x Megamodule Reference Guide Describes the TMS320C64x digital signal processor DSP megamodule Included is a discussion on the internal direct memory access IDMA controller the interrupt controller the power down controller memory protection bandwidth management and the memory and cache C6000 TMS320C6000 Code Composer Studio are trademarks of Texas Instruments All other trademarks are the property of their respective owners 10 Preface SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated User s Guide Lee E SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 1 Introduction This document provides a functional description of the Ethernet Media Access Controller EMAC and Physical layer PHY device Ma
196. onents There are two EMAC modules integrated with the TC16486 C6472 device EMACO interfaces with PHY through one of five interfaces MII GMII S8MII RMII or RGMII EMAC1 interfaces with PHY through one of three interfaces S3MII RMII or RGMII In Figure 22 the number associated with each MII interface shows the EMAC module with which the interface is available For example RMIIO is EMACO interface RMII1 is EMAC1 interface Figure 22 EMAC Module Block Diagram Clock and reset logic Receive Receive address MAC Configuration bus Receive P MIIO GMIIO CPPI DMA engine FIFO receiver GE RMIIO RMII1 ee Transmit Transmit MAC DMA engine FIFO transmitter RGMIIO RGMII1 S3MII0 S3MII1 Interrupt EMIC Eet controller Control Statistics Each EMAC peripheral used has the following components e The receive path Receive DMA engine The receive DMA engine performs the data transfer between the receive FIFO and the device internal or external memory It interfaces to the processor through the bus arbiter in the CPPI buffer manager This DMA engine is totally independent of the TCI6486 C6472 DSP EDMA Receive FIFO The receive FIFO consists of 68 cells of 64 bytes each and the associated control logic The FIFO buffers receive data in preparation for writing into packet buffers in device memory and also enable receive FIFO flow control MAC receiver The MAC receiver det
197. ontain a CRC error because they are created in the transmitting MAC so these error conditions have no effect on this statistic Pause frames sent by software are not included in this count Since pause frames are only transmitted in full duplex mode carrier loss and collisions have no effect on this statistic Transmitted pause frames are always 64 byte multicast frames so appear in the multicast transmit frames register and 64 octect frames register statistics 5 50 18 Deferred Transmit Frames Register TXDEFERRED The total number of frames transmitted on the EMAC that first experienced deferment Such a frame is defined as having all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address e Was any size e Had no carrier loss and no underrun e Experienced no collisions before being successfully transmitted e Found the medium busy when transmission was first attempted so had to wait CRC errors have no effect on this statistic 5 50 19 Transmit Collision Frames Register TXCOLLISION The total number of times that the EMAC experienced a collision Collisions occur under two circumstances e When a transmit data or MAC control frame has all of the following Was destined for any unicast broadcast or multicast address Was any size Had no carrier loss and no underrun Experienced a collision A jam sequence is sent for every non late collision so this statistic incr
198. ontrol 2 10 1 4 Collision Based Receive Buffer Flow Control Collision based receive buffer flow control provides a means of preventing frame reception when the EMAC is operating in half duplex mode FULLDUPLEX bit is cleared in MACCONTROL register When receive flow control is enabled and triggered the EMAC generates collisions for received frames The jam sequence transmitted is the 12 byte sequence C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 in hexadecimal The jam sequence begins approximately when the source address starts to be received These forced collisions are not limited to a maximum of 16 consecutive collisions and are independent of the normal back off algorithm Receive flow control does not depend on the value of the incoming frame destination address A collision is generated for any incoming packet regardless of the destination address if any EMAC enabled channel s free buffer register value is less than or equal to the channel s flow threshold value 2 10 1 5 IEEE 802 3X Based Receive Buffer Flow Control IEEE 802 3x based receive buffer flow control provides a means of preventing frame reception when the EMAC is operating in full duplex mode the FULLDUPLEX bit is set in the MACCONTROL register When receive flow control is enabled and triggered the EMAC transmits a pause frame to request that the sending station stop transmitting for the period indicated within the transmitted pause frame The EMAC transmits a pause frame to the
199. out This Manual This document provides a functional description of the Ethernet Media Access Controller EMAC and Physical layer PHY device Management Data Input Output MDIO module integrated with TMS320TCI6486 TMS320C6472 devices Included are the features of the EMAC and MDIO modules a discussion of their architecture and operation how these modules connect to the outside world and the registers descriptions for each module Notational Conventions This document uses the following conventions e Hexadecimal numbers are shown with the suffix h For example the following number is 40 hexadecimal decimal 64 40h e Registers in this document are shown in figures and described in tables Each register figure shows a rectangle divided into fields that represent the fields of the register Each field is labeled with its bit name its beginning and ending bit numbers above and its read write properties below A legend explains the notation used for the properties Reserved bits in a register figure designate a bit that is used for future device expansion Related Documentation From Texas Instruments The following documents describe the C6000 devices and related support tools Copies of these documents are available on the Internet Tip Enter the literature number in the search box provided at www ti com SPRU189 TMS320C6000 DSP CPU and Instruction Set Reference Guide Describes the CPU architecture pipeline instructi
200. ovides the timing reference for transmit operations in 10 100 Mbps mode The MTXD and MTXEN signals are tied to this clock when in 10 100 Mbps mode The clock is generated by the PHY and is 2 5 MHz at 10 Mbps operation and 25 MHz at 100 Mbps operation GMI source synchronous transmit clock GMTCLKk This clock is used in 1000 Mbps mode only providing a continuous 125 MHz frequency for transmit operations The MTXD and MTXEN signals are tied to this clock when in Gigabit mode The clock is generated by the EMAC and is 125 MHz Transmit data MTXD The transmit data pins are a collection of 8 data signals comprising 8 bits of data MTDXO is the least significant bit LSB The signals are synchronized by MTCLK in 10 100 Mbps mode and by GMTCLK in Gigabit mode and valid only when MTXEN is asserted Transmit enable MTXEN The transmit enable signal indicates that the MTXD pins are generating nibble data for use by the PHY It is driven synchronously to MTCLK in 10 100 Mbps mode and to GMTCLK in Gigabit mode Collision detected MCOL The MCOL pin is asserted by the PHY when it detects a collision on the network It remains asserted while the collision condition persists This signal is not necessarily synchronous to MTCLK nor MRCLK This pin is used in half duplex operation only Carrier sense MCRS The MCRS pin is asserted by the PHY when the network is not idle in either transmit or receive The pin is de asserted when both transmit and re
201. owledge and agree that any such use of TI products which TI has not designated as military grade is solely at the Buyer s risk and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO TS 16949 requirements Buyers acknowledge and agree that if they use any non designated products in automotive applications TI will not be responsible for any failure to meet such requirements Following are URLs where you can obtain information on other Texas Instruments products and application solutions Products Applications Amplifiers amplifier ti com Audio www ti com audio Data Converters dataconverter ti com Automotive www ti com automotive DLP Products www dp com Communications and www ti com communications Telecom DSP dsp ti com Computers and www ti com computers Peripherals Clocks and Timers www ti com clocks Consumer Electronics www ti com consumer apps Interface interface ti com Energy www ti com energy Logic logic ti com Industrial www ti com industrial Power Mgmt power ti com Medical www ti com medical Microcontrollers microcontroller ti com Security www ti com security RFID www ti rfid com Space Avionics amp www ti com space avionics defense Defense RF IF and ZigBee Solutions
202. porated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 12 MDIO User Access Register 0 USERACCESSO The MDIO user access register 0 USERACCESSO is shown in Figure 39 and described in Table 32 Figure 39 MDIO User Access Register 0 USERACCESS0 31 30 29 28 oe 25 ou 20 16 GO WRITE ACK Reserved REGADR PHYADR R WS 0 R W 0 DW R 0 R W 0 R W 0 15 0 DATA R W 0 LEGEND R Read only R W Read Write R WS Read Write 1 to set n value after reset Table 32 MDIO User Access Register 0 USERACCESSO0 Field Descriptions Bit Field Value Description 31 GO Go bit Writing a 1 to this bit causes the MDIO state machine to perform an MDIO access when it is convenient for it to do so this is not an instantaneous process Writing a 0 to this bit has no effect This bit is writeable only if the MDIO state machine is enabled This bit will self clear when the requested access has been completed Any writes to the USERACCESSO register are blocked when the GO bit is 1 30 WRITE Write enable bit Setting this bit to a 1 causes the MDIO transaction to be a register write otherwise it is a register read 0 The user command is a read operation The user command is a write operation 29 ACK Acknowledge bit This bit is set if the PHY acknowledged the read transaction 28 26 Reserved 0 Reserved 25 21 REGADR Register address bits This field specifies the P
203. possible is transferred to the promiscuous channel until overrun The appropriate overrun statistic s is incremented and the OVERRUN and NOMATCH flags are set in the SOP buffer descriptor Note that the RXMAXLEN number of bytes cannot be reached for an overrun to occur it would be truncated and be a jabber or oversize 1 X 0 Overrun frame filtered with the appropriate overrun statistic s incremented 1 X 1 As much frame data as possible is transferred to the address match channel until overrun The appropriate overrun statistic s is incremented and the OVERRUN flag is set in the SOP buffer descriptor Note that the RXMAXLEN number of bytes cannot be reached for an overrun to occur it would be truncated Packet Transmit Operation The transmit DMA is an eight channel interface Priority between the eight queues may be either fixed or round robin as selected by the TXPTYPE bit in the MACCONTROL register If the priority type is fixed then channel 7 has the highest priority and channel 0 has the lowest priority Round robin priority proceeds from channel 0 to channel 7 Transmit DMA Host Configuration To configure the transmit DMA for operation the host must perform the following e Write the MACSRCADDRLO and MACSRCADDRHI registers used for pause frames on transmit C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l TEX
204. pts to one of the CPU s interrupts Once the interrupt is mapped to a CPU interrupt general masking and unmasking of the interrupt to control reentrancy should be done at the chip level by manipulating the interrupt enable mask The EMIC module interrupt control register EW_INTCTL should only enable and disable interrupts from within the EMAC interrupt service routine ISR as disabling and re enabling the interrupt in EW_INTCTL also resets the interrupt pace counter 2 16 3 MDIO Module Initialization The MDIO module initially configures and monitors one or more external PHY devices Other than initializing the software state machine details on the MDIO state machine can be found in the IEEE 802 3 standard the MDIO module only needs the MDIO engine enabled and the clock divider configured To set the clock divider supply an MDIO clock of 1 MHz As the peripheral clock is used as the base clock CPUclIk 6 the divider can be set to 125 for a 750 MHz device Slower MDIO clocks for slower CPU frequencies are acceptable Both the state machine enable and the MDIO clock divider are controlled through the MDIO control register CONTROL If none of the potentially connected PHYs require the access preamble the PREAMBLE bit can also be set in CONTROL to speed up PHY register access See Example 4 for an example of the code for initialization Example 4 MDIO Module Initialization Code define PCLK 125 Enable MDIO and setup divider
205. r reset Table 72 MAC Source Address High Bytes Register MACSRCADDRHI Field Descriptions Bit Field Value Description 31 24 MACSRCADDR2 MAC source address bits 23 16 byte 2 23 16 MACSRCADDR3 MAC source address bits 31 24 byte 3 15 8 MACSRCADDR4 MAC source address bits 39 32 byte 4 7 0 MACSRCADDR5 MAC source address bits 47 40 byte 5 134 C6472 TC16486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l www t TEXAS INSTRUMENTS i com EMAC Port Registers 5 37 MAC Hash Address Register 1 MACHASH1 The MAC hash registers allow group addressed frames to be accepted on the basis of a hash function of the address The hash function creates a 6 bit data value hash_fun from the 48 bit destination address DA as follows Hash_fun 0 DA 0 XOR DA 6 XOR DA 12 XOR DA 18 XOR DA 24 XOR DA 30 XOR DA 36 XOR DA 42 Hash_fun 1 DA 1 XOR DA 7 XOR DA 13 XOR DA 19 XOR DA 25 XOR DA 31 XOR DA 37 XOR DA 43 Hash_fun 2 DA 2 XOR DA 8 XOR DA 14 XOR DA 20 XOR DA 26 XOR DA 32 XOR DA 38 XOR DA 44 Hash_fun 3 DA 3 XOR DA 9 XOR DA 15 XOR DA 21 XOR DA 27 XOR DA 33 XOR DA 39 XOR DA 45 Hash_fun 4 DA 4 XOR DA 10 XOR DA 16 XOR DA 22 XOR DA 28 XOR DA 34 XOR DA 40 XOR DA 46 Hash_fun 5 DA 5 XOR DA 11 XOR DA 17 XOR DA 23 XOR DA 29 XOR DA 35 XOR DA 41 XOR DA 47 This function
206. rdown command to an inactive channel issues an interrupt that software should acknowledge with an FFFF FFFCh acknowledge value to TXnCP note that there is no buffer descriptor Software may read the interrupt acknowledge location TXnCP to determine if the interrupt was due to a commanded teardown The read value is FFFF FFFCh if the interrupt was due to a teardown command Receive and Transmit Latency The transmit FIFO contains twenty four 64 byte cells and the receive FIFO contains sixty eight 64 byte cells The EMAC begins transmission of a packet on the wire after TXCELLTHRESH cells configurable through the FIFOCONTROL register or a complete packet are available in the FIFO Transmit underrun cannot occur for packet sizes of TXKCELLTHRESH times 64 bytes or less For larger packet sizes transmit underrun can occur if the memory latency is greater than the time required to transmit a 64 byte cell on the wire this is 0 512 us in 1 Gbit mode 5 12 us in 100 Mbps mode and 51 2 us in 10 Mbps mode The memory latency time includes all buffer descriptor reads for the entire cell data The EMAC transmit FIFO uses 24 cells thus underrun cannot happen for a normal size packet less than 1536 packet bytes Cell transmission can be configured to start only after an entire packet is contained in the FIFO for a maximum size packet set the TXCELLTHRESH field to the maximum possible value of 24 Receive overrun is prevented if the receive memory
207. received frame This is meaningful only during data reception when RMCRSDV is active It is driven synchronously to the RMII reference clock MDCLK O Management data clock MDCLK The MDIO data clock is sourced by the MDIO module on the system Itis used to synchronize MDIO data access operations done on the MDIO pin The frequency of this clock is controlled by the CLKDIV bits in the MDIO control register CONTROL MDIO UO Management data input output MDIO The MDIO pin drives PHY management data into and out of the PHY by way of an access frame consisting of start of frame read write indication PHY address register address and data bit cycles The MDIO pin acts as an output for everything except the data bit cycles when the pin acts as an input for read operations The 50 MHz reference clock RMREFCLK for the RMII gasket is sourced externally through a zero delay clock buffer If multiple RMII PHY ports are used all device RMII reference clocks must come from same zero delay clock buffer On the TC16486 C6472 device RMII pins are multiplexed with other non RGMII pins When using the RMIIO port on EMACO there are no restrictions on the available EMAC1 Ethernet interfaces RMII1 S3MII1 and RGMII1 are useable When using the RMII1 port on EMAC1 the EMACO Ethernet interfaces not available due to pin multiplexing are GMIIO MIIO The RMIIO SSMIIO and RGMIIO ports are available on EMACO Ethernet interfaces when using the RMII1 port on
208. require that transmitters defer nor do they monitor or react to receive activity as there is no contention for a shared medium in this mode Full duplex mode can only be used when all of the following are true e The physical medium is capable of supporting simultaneous transmission and reception without interference e There are exactly two stations connected with a full duplex point to point link As there is no contention for use of a shared medium the multiple access i e CSMA CD algorithms are unnecessary e Both stations on the LAN are capable of and have been configured to use full duplex operation The most common configuration envisioned for full duplex operation consists of a central bridge also known as a switch with a dedicated LAN connecting each bridge port to a single device Full duplex operation constitutes a proper subset of the MAC functionality required for half duplex operation Half Duplex In half duplex mode the CSMA CD media access method is the means by which two or more stations share a common transmission medium To transmit a station waits defers for a quiet period on the medium that is no other station is transmitting It then sends the intended message in bit serial form If after initiating a transmission the message collides with that of another station then each transmitting station intentionally transmits for an additional predefined period to ensure propagation of the collision throughout
209. reserved multicast address at the first available opportunity immediately if currently idle or following the completion of the frame currently being transmitted The pause frame contains the maximum possible value for the pause time FFFFh The EMAC counts the receive pause frame time decrements FFOOh to 0 and retransmits an outgoing pause frame if the count reaches zero When the flow control request is removed the EMAC transmits a pause frame with a zero pause time to cancel the pause request Note that transmitted pause frames are only a request to the other end station to stop transmitting Frames that are received during the pause interval are received normally provided the receive FIFO is not full Pause frames are transmitted if enabled and triggered regardless of whether or not the EMAC is observing the pause time period from an incoming pause frame The EMAC transmits pause frames as described below e The 48 bit reserved multicast destination address 01 80 C2 00 00 01h e The 48 bit source address set via the MACSRCADDRLO and MACSRCADDRHI registers e The 16 bit length type field containing the value 88 08h e The 16 bit pause opcode equal to 00 01h e The 16 bit pause time value of FF FFh A pause quantum is 512 bit times Pause frames sent to cancel a pause request have a pause time value of 00 00h SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 20
210. rite operation to the PHY is scheduled and completed by the MDIO module Completion of the write operation can be determined by polling the GO bit in USERACCESSn for a 0 4 Completion of the operation sets the corresponding bit in the USERINTRAW register for the USERACCESSn used If interrupts have been enabled on this bit using the USERINTMASKSET register then the bit is also set in the USERINTMASKED register and an interrupt is triggered on the DSP 2 8 2 3 Reading Data From a PHY Register The MDIO module includes a user access register USERACCESSn to directly access a specified PHY device To read a PHY register perform the following 1 Ensure that the GO bit in the USERACCESSn register is cleared 2 Write to the GO REGADR and PHYADR bits in USERACCESSn corresponding to the desired PHY and PHY register 3 The read data value is available in the DATA bits of USERACCESSn after the module completes the read operation on the serial bus Completion of the read operation can be determined by polling the GO and ACK bits in USERACCESSn Once the GO bit has cleared the ACK bit is set on a successful read 4 Completion of the operation sets the corresponding bit in the USERINTRAW register for the USERACCESSn used If interrupts have been enabled on this bit using the USERINTMASKSET register then the bit is also set in the USERINTMASKED register and an interrupt is triggered on the DSP 2 8 2 4 Example of MDIO Register Access Code The M
211. rsized fragment frames are transferred 1 X 1 1 1 All address matching frames with and without errors transferred to the address match channel Receive Overrun The types of receive overruns are e FIFO start of frame overrun FIFO_SOF e FIFO middle of frame overrun FIFO_MOF e DMA start of frame overrun DMA_SOF e DMA middle of frame overrun DMA_MOF The statistics counters used to track these types of receive overruns are e Receive Start of Frame Overruns Register RXSOFOVERRUNS e Receive Middle of Frame Overruns Register RXMOFOVERRUNS e Receive DMA Overruns Register RXDMAOVERRUNS Start of frame overruns happen when there are no resources available when frame reception begins Start of frame overruns increment the appropriate overrun statistic s and the frame is filtered Middle of frame overruns happen when there are some resources to start the frame reception but the resources run out during frame reception In normal operation a frame that overruns after starting the frame reception is filtered and the appropriate statistic s are incremented however the RXCEFEN bit in the RXMBPENABLE register affects overrun frame treatment Table 15 shows how the overrun condition is handled for the middle of frame overrun Table 15 Middle of Frame Overrun Treatment Address Match RXCAFEN RXCEFEN Middle of Frame Overrun Treatment 0 0 X Overrun frame filtered 0 1 0 Overrun frame filtered 0 1 1 As much frame data as
212. s Incorporated I TEXAS INSTRUMENTS MDIO Registers www ti com 4 7 MDIO Link Status Change Interrupt Masked Register LINKINTMASKED The MDIO link status change interrupt masked register LINKINTMASKED is shown in Figure 34 and described in Table 27 Figure 34 MDIO Link Status Change Interrupt Masked Register LINKINTMASKED 31 16 Reserved R 0 15 2 1 0 LINKINT Reserved MASKED R 0 R WC 0 LEGEND R Read only R WC Read Write 1 to clear n value after reset Table 27 MDIO Link Status Change Interrupt Masked Register LINKINTMASKED Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 0 LINKINTMASKED MDIO Link change interrupt masked value hen asserted a bit indicates that there was an MDIO link change event a change in the LINK register corresponding to the PHY address in the USERPHYSEL register and the corresponding LINKINTENB bit was set LINKINTRAW 0 and LINKINTRAW 1 correspond to USERPHYSELO and USERPHYSEL1 respectively Writing a 1 will clear the event and writing 0 has no effect 82 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com MDIO Registers 4 8 MDIO User Command Complete Interrupt Unmasked Register USERINTRAW The MDIO user command complete interrupt unmasked register U
213. s Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 17 2 1 Link Change Interrupt The MDIO module asserts a link change interrupt LINKINT if there is a change in the link state of the PHY corresponding to the address in the PHYADRMON bits in the USERPHYSELn register and if the LINKINTENB bit is also set in USERPHYSELn This interrupt event is also captured in the LINKINTRAW bits of the LINKINTRAW register The LINKINTRAW bits 0 and 1 correspond to USERPHYSELO and USERPHYSEL1 respectively When the interrupt is enabled and generated the corresponding bit is also set in the LINKINTMASKED register The interrupt is cleared by writing back the same bit to LINKINTMASKED write to clear 2 17 2 2 User Access Completion Interrupt A user access completion interrupt USERINT is asserted when the GO bit in one of the USERACCESSn registers transitions from 1 to 0 indicating completion of a user access and the bit in the USERINTMASKSET register corresponding to USERACCESS0 or USERACCESS1 is set This interrupt event is also captured in bits 0 and 1 of the USERINTRAW register USERINTRAW bits 0 and bit 1 correspond to USERACCESS0 and USERACCESS1 respectively When the interrupt is enabled and generated the corresponding USERINTMASKED bit is also set in the USERINTMASKED register The interrupt is cleared by writing back the same bit to USERINTMASKED write to clear 2 17 3 Proper Interrupt Processing
214. s the in band signals coming in on its receive 17 GIGFORCE Gigabit force mode This bit is used to force the EMAC into gigabit mode if the input MTCLK signal has been stopped by the PHY 16 RMIIDUPLEXMODE Duplex mode for the RMII interface 0 The RMII operates in half duplex mode This mode is not supported in the TC16486 C6472 devices 1 The RMII operates in full duplex mode 15 RMIISPEED Operating speed for the RMII interface 0 The RMII operates at 2 5 MHz 10Mbps mode 1 The RMII operates at 25 MHz 100 Mbps mode 14 RXOFFLENBLOCK Receive offset length word write block 0 Do not block the DMA writes to the receive buffer descriptor offset buffer length word 1 Block all EMAC DMA controller writes to the receive buffer descriptor offset buffer length words during packet processing When this bit is set the EMAC will never write the third word to any receive buffer descriptor 13 RXOWNERSHIP Receive ownership write bit value 0 The EMAC writes the Receive ownership bit to zero at the end of packet processing 1 The EMAC writes the Receive ownership bit to one at the end of packet processing If you do not use the ownership mechanism you can set this mode to preclude the necessity of software having to set this bit each time the buffer descriptor is used SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO 125 Copyright 2006 2010 Texas Instruments Incorporated EMAC
215. s will all return a value of zero The interface to be used MII RMII GMII or RGMII is automatically selected at power on reset based on the state of the MACSEL configuration pins EMAC MDIO is enabled through the chip level module state control register 0 MDCTLO and module status register 0 MDSTATO For detailed information on the programming sequence see the TMS320TCI6486 Communications Infrastructure Digital Signal Processor data manual SPRS300 or the TMS320C6472 Fixed Point Digital Signal Processor data manual SPRS612 This sequence enables the EMAC peripheral and the register values are reset to default Module specific initialization may proceed 2 16 2 EMIC Module Initialization The EMIC module is used for global interrupt enable and to pace back to back interrupts using an interrupt re trigger count based on the peripheral clock CPUCLK 6 Note that although the EMIC module and the EMAC module have slightly different functions in practice the type of maintenance performed on the EMIC module is more commonly conducted from the EMAC module software as opposed to the MDIO module The initialization of the EMIC module consists of two parts 1 Configuration of the interrupt on the DSP 2 Initialization of the EMIC module e Setting the interrupt pace count delay and prescaler e Initializing the EMAC and MDIO modules e Enabling interrupts in the EW_INTCTL Use the system s interrupt controller to map the EMAC interru
216. se frames are transferred to memory Transmit flow control is disabled Full duplex mode incoming pause frames are not acted upon Transmit flow control is enabled Full duplex mode incoming pause frames are acted upon RXBUFFERFLOWEN Receive buffer flow control enable bit Receive flow control is disabled Half duplex mode no flow control generated collisions are sent Full duplex mode no outgoing pause frames are sent Receive flow control is enabled Half duplex mode collisions are initiated when receive buffer flow control is triggered Full duplex mode outgoing pause frames are sent when receive flow control is triggered Reserved Reserved LOOPBACK Loopback mode The loopback mode forces internal full duplex mode regardless of the FULLDUPLEX bit The loopback bit should be changed only when the GMIIEN bit is de asserted Loopback mode is disabled Loopback mode is enabled FULLDUPLEX Full duplex mode The gigabit mode forces full duplex mode regardless of whether the FULLDUPLEX bit is set or not Half duplex mode is enabled Full duplex mode is enabled 126 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 5 30 MAC Status Register MACSTATUS The MAC status register MACSTATUS is shown in Figure 72 and described in Table 66 3
217. sion medium is busy it waits until it senses no signal energy plus an inter packet gap time and then starts to transmit the frame While transmitting the port monitors for the presence of signal energy coming from other ports If the port transmits the entire frame without detecting signal energy from other ethernet devices the port is finished with the frame lf the port detects signal energy from other ports while transmitting it stops transmitting its frame and instead transmits a 48 bit jam signal After transmitting the jam signal the port enters an exponential back off phase Specifically when transmitting a given frame after experiencing a number of collisions in a row for the frame the port chooses a random value that is dependent on the number of collisions The port then waits an amount of time which is multiple of this random value and returns to Step 1 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 5 Programming Interface 2 5 1 Packet Buffer Descriptors The buffer descriptor is a central part of the EMAC module It determines how the application software describes ethernet packets to be sent and empty buffers to be filled with incoming packet data The basic descriptor format is shown in Figure 10 and described in Table 13
218. smit channel 5 6h Teardown transmit channel 6 7h Teardown transmit channel 7 SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 97 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 4 Receive Identification and Version Register RXIDVER The receive identification and version register RXIDVER is shown in Figure 46 and described in Table 40 Figure 46 Receive Identification and Version Register RXIDVER 31 16 RXIDENT 0x000C 15 11 10 8 7 0 RTLVER RXMAJORVER RXMINORVER 0x01 0x02 0x08 LEGEND R Read only n value after reset Table 40 Receive Identification and Version Register RXIDVER Field Descriptions Bit Field Value Description 31 16 RXIDENT Receive identification value 15 11 RTLVER RTL version value 10 8 RXMAJORVER Receive major version value 7 0 RXMINORVER Receive minor version value 98 C6472 TC16486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 5 Receive Control Register RXCONTROL The receive control register RXCONTROL is shown in Figure 47 and described in Table 41 Figure 47 Receive Control Register RXCONTROL
219. software application If these two values do not match the interrupt is active The system configuration determines whether an active interrupt can interrupt the CPU In general the global interrupt for EMAC and MDIO must be enabled in the EMIC module and it also must be mapped in the DSP interrupt controller and enabled as a CPU interrupt If the system is configured properly the interrupt for a specific receive or transmit channel executes under these conditions when the corresponding interrupt is enabled in the EMAC using the RXINTMASKSET or TXINTMASKSET registers The current state of the receive or transmit channel interrupt can be examined directly by the software application by reading the RXINTSTATRAW and TXINTSTATRAW registers whether or not the interrupt is enabled Interrupts are acknowledged when the application software updates the value of TXnCP or RXnCP with a value that matches the internal value kept by the EMAC This mechanism ensures that the application software never misses an EMAC interrupt as the interrupt and its acknowledgment are tied directly to the actual buffer descriptors processing SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 33 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture A TEXAS INSTRUMENTS www ti com 2 5 4 Transmit Buffer Descriptor Format A transmit TX
220. t channel 5 pending interrupt mask Write 1 to disable interrupt 4 TX4PENDMASK 0 Transmit channel 4 pending interrupt mask Write 1 to disable interrupt 3 TX38PENDMASK 0 Transmit channel 3 pending interrupt mask Write 1 to disable interrupt 2 TX2PENDMASK 0 Transmit channel 2 pending interrupt mask Write 1 to disable interrupt 1 TX1PENDMASK 0 Transmit channel 1 pending interrupt mask Write 1 to disable interrupt 0 TXOPENDMASK 0 Transmit channel 0 pending interrupt mask Write 1 to disable interrupt 104 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 11 MAC Input Vector Register MACINVECTOR The MAC input vector register MACINVECTOR is shown in Figure 53 and described in Table 47 Figure 53 MAC Input Vector Register MACINVECTOR 31 an 29 um 1417 46 USER LINK HOST STAT INT INT Reserved PEND PEND RO RO R 0 RO RO 15 8 7 0 RXPEND TXPEND R 0 R 0 LEGEND R Read only n value after reset Table 47 MAC Input Vector Register MACINVECTOR Field Descriptions Bit Field Value Description 31 USERINT MDIO module user interrupt USERINT pending status bit 30 LINKINT MDIO module link change interrupt LINKINT pending status bit 29 18 Reserved 0 Reserved 17 HOSTP
221. t clock after the link signal goes high Any packet transmission attempt within 4096 clock cycles of transmit clock will not cause an actual packet transmission over the RGMII interface This restriction on packet transmissions calls for a delay in the packet transmission after device reset An approximate delay of 2 ms after reset should be enough to start packet transmissions 2 15 4 S3MIl Transmission 64 On device reset packet transmissions on the S3MIl interface are precluded for 4096 transmit clock cycles after the S3MII link signal goes high Transmission can be started only after 4096 cycles of transmit clock after the link signal goes high Any packet transmission attempt within 4096 clock cycles of transmit clock will not cause an actual packet transmission over the S3MIl interface This restriction on packet transmissions calls for a delay in the packet transmission after device reset An approximate delay of 2 ms after reset should be enough to start packet transmissions C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 16 Initialization 2 16 1 Enabling the EMAC MDIO Peripheral When the device is powered on the EMAC peripheral is disabled Prior to EMAC specific initialization the EMAC must be enabled otherwise its registers cannot be written and the read
222. ta frames transferred to promiscuous channel No control frames are transferred 0 1 1 1 0 Proper oversize jabber code align CRC data and control frames transferred to promiscuous channel No undersized frames are transferred 0 1 1 1 1 All non address matching frames with and without errors transferred to promiscuous channel 1 X 0 0 0 Proper data frames transferred to address match channel 1 X 0 0 1 Proper undersized data frames transferred to address match channel 1 X 0 1 0 Proper data and control frames transferred to address match channel 1 X 0 1 1 Proper undersized data and control frames transferred to address match channel 1 X 1 0 0 Proper oversize jabber code align CRC data frames transferred to address match channel No control or undersized frames are transferred 1 X 1 0 1 Proper oversize jabber fragment undersized code align CRC data frames transferred to address match channel No control frames are transferred SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO_ 61 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 2 11 9 2 12 2 12 1 62 A TEXAS INSTRUMENTS EMAC Functional Architecture www ti com Table 14 Receive Frame Treatment Summary continued Address RXMBPENABLE Bits Match RXCAFEN RXCEFEN RXCMFEN RXCSFEN Frame Treatment 1 X 1 1 0 Proper oversize jabber code align CRC data and control frames transferred to address match channel No unde
223. te RAM block The write generates the interrupt when enabled by the interrupt mask regardless of the value written Upon interrupt reception the CPU processes one or more packets from the buffer chain and then acknowledges an interrupt by writing the address of the last buffer descriptor processed to the queue s associated TX completion pointer in the transmit DMA state RAM The data written by the host buffer descriptor address of the last processed buffer is compared to the data in the register written by the EMAC port address of last buffer descriptor used by the EMAC If the two values are not equal indicating that the EMAC has transmitted more packets than the CPU has processed interrupts for then the transmit packet completion interrupt signal remains asserted If the two values are equal indicating that the host has processed all packets that the EMAC has transferred then the pending interrupt is cleared Reading the TXnCP register displays the value that the EMAC is expecting The EMAC write to the completion pointer stores the value in the state RAM The CPU written value does not change the register value The host written value is compared to the register content which was written by the EMAC If the two values are equal then the interrupt is removed otherwise the interrupt remains asserted The host may process multiple packets prior to acknowledging an interrupt or the host may acknowledge interrupts for every packet 2 17 1
224. ter Register RXnNHDP 31 16 RXnHDP DW 15 0 RXnHDP RIW x LEGEND R W Read Write n value after reset Table 83 Receive Channel n DMA Head Descriptor Pointer Register RXnNHDP Field Descriptions Bit Field Value Description 31 0 RXnHDP Receive channel n DMA Head Descriptor pointer Writing a receive DMA buffer descriptor address to this location allows receive DMA operations in the selected channel when a channel frame is received Writing to these locations when they are nonzero is an error except at reset Host software must initialize these locations to zero on reset SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 145 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 48 Transmit Channel 0 7 Completion Pointer Register TXnCP The transmit channel 0 7 completion pointer register TXnCP is shown in Figure 90 and described in Table 84 Figure 90 Transmit Channel n Completion Pointer Register TXnCP 31 16 TXnCP R W x 15 0 TXnCP R W x LEGEND R W Read Write n value after reset Table 84 Transmit Channel n Completion Pointer Register TXnCP Field Descriptions Bit Field Value Description 31 0 TXnCP Transmit channel n completion pointer register is written by the host with the buffer descriptor address for the last buffer pr
225. that the SM does not stay in the grayed state While in the transitional state it typically does an operation like setting the counter to a certain value Figure 17 DSM State Transition Diagram EVT_PULSE 0 or EVT_PULSE 1 amp amp CNT gt CNT_CFG amp amp TIME_CFG I 0 A Co gt A Ae W EX S P gt XY ok Ly Q SSO Oo a A ON qy SE G i As w die Sa Yak A o DS ao woe Vr END A AN Jo SE 7 Q D o SS Ee On amp Sey w LS i O V S SSL A ZS g TS KY ae A S GS EVT_PULSE 0_ NS e amp amp CR 0 gt te A l l 1 amp amp O EVT_PULSE 1 amp amp 5 CR 1 amp amp CNT lt l ONT CEG CNT gt CNT_CFG giz amp amp EVT_PULSE 1 36 7 av oe Jk Ez go SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback C6472 TCI6486 EMAC MDIO Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com 2 7 4 EMAC Functional Architecture Transmit Pacer and Interrupt Combiner TPIC The transmit pacer and interrupt combiner TPIC block performs the following functions Optionally implements pacing for transmit events Combines the output of the pacer module based on the settings of the bits 8 to 15 in the EW_INTCTL register and generates a single MACTXINT interrupt per the C64x megamodule Receives a single PS_TICK and forwards it to all the pacing blocks Allows per interrupt enabling or disabling of the interrup
226. the DEVCTL register Table 2 describes the EMAC1_EN pin Table 2 EMAC1_EN Pin Description Value Description 0 EMAC1 is disabled or not used Pulls on EMAC1 I O are enabled except RGMII pins and the corresponding I O buffers are powered down SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 13 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS Introduction www ti com Table 2 EMAC1_EN Pin Description continued Value Description 1 EMAC1 is enabled and used Pulls on EMAC1 I O are disabled except RGMII pins and the corresponding UO buffers are powered up except RGMII output only pins NOTE RGMII buffers are HSTL buffers with no internal pulls RGMII output only pins will always be powered down even when the module is enabled EMAC1_EN is also software programmable through the DEVCTL register A write to the DEVCTL register is key protected by the DEVCTL_KEY register For details of MACSELO MACSEL1 and EMAC1_EN decoding see Section 2 3 1 4 Industry Standard s Compliance Statement The EMAC peripheral conforms to the IEEE 802 3 standard describing the Carrier Sense Multiple Access with Collision Detection CSMA CD Access Method and Physical Layer specifications ISO IEC has also adopted the IEEE 802 3 standard and re designated it as ISO IEC 8802 3 2000 E In difference from this standard the EMAC peripheral i
227. the system The station remains silent for a random amount of time back off before attempting to transmit again Host The host is an intelligent system resource that configures and manages each communications control module The host is responsible for allocating memory initializing all data structures and responding to port EMAC interrupts In this document host refers to the TMS320TC16486 TMS320C6472 device Jabber A condition wherein a station transmits for a period of time longer than the maximum permissible packet length usually due to a fault condition SPRUEF8F March 2006 Revised November 2010 Glossary 157 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS Appendix A www ti com Jumbo Packets Jumbo frames are defined as those packets whose length exceeds the standard Ethernet MTU which is 1500 kbytes For the C64x devices it is recommended not to use packets exceeding 35K in length The PHY that you use can place additional limits on to the length of the packets that you can transfer in a system Link The transmission path between any two instances of generic cabling Multicast MAC Address A class of MAC address that sends a packet to potentially more than one recipient A group address is specified by setting the LSB of the first MAC address byte Thus 01h 02h 03h 04h 05h 06h is a valid multicast address Typically an Ethernet MAC looks for only
228. the transmit and receive algorithms to Sequence generate a CRC value for the FCS field The frame check sequence covers the 60 to RXMAXLEN 4 bytes of the packet data Note that the 4 byte FCS field may not be included as part of the packet data depending on the EMAC configuration SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 29 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Functional Architecture www ti com 2 4 2 30 Multiple Access Protocol Nodes in an ethernet local area network are interconnected by a broadcast channel As a result when an EMAC port transmits a frame all of the adapters on the local network receive the frame Carrier sense multiple access with collision detection CSMA CD algorithms are used when the EMAC operates in half duplex mode When operating in full duplex mode there is no contention for use of a shared medium because there are exactly two ports on the local network Each port runs the CSMA CD protocol without explicit coordination with the other ports on the ethernet network Within a specific port the CSMA CD protocol is as follows 1 2 The port obtains data from upper layer protocols at its node prepares an ethernet frame and puts the frame in a buffer If the port senses that the medium is idle it starts to transmit the frame If the port senses that the transmis
229. tic 5 50 22 Transmit Excessive Collision Frames Register TXEXCESSIVECOLL The total number of frames when transmission was abandoned due to excessive collisions Such a frame is defined as having all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address e Was any size e Had no carrier loss and no underrun e Experienced 16 collisions before abandoning all attempts at transmitting the frame None of the collisions were late CRC errors have no effect on this statistic 5 50 23 Transmit Late Collision Frames Register TXLATECOLL The total number of frames when transmission was abandoned due to a late collision Such a frame is defined as having all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address e Was any size e Had no carrier loss and no underrun e Experienced a collision later than 512 bit times into the transmission There may have been up to 15 previous non late collisions that had previously required the transmission to be re attempted The late collisions statistic dominates over the single multiple and excessive collisions statistics If a late collision occurs the frame is not counted in any of these other three statistics CRC errors carrier loss and underrun have no effect on this statistic 5 50 24 Transmit Underrun Error Register TXUNDERRUN The number of frames sent by the EMAC that experienced FIFO
230. transmit enable signal indicates that the RGTXD pins are generating nibble data for use by the PHY It is driven synchronously to RGTXC RGREFCLK O Reference clock RGREFCLK This 125 MHz reference clock is provided as a convenience It can be used as a clock source to the PHY so that the PHY may generate the RGRXC clock to be sent to EMAC This clock is stopped while the device is in reset RGRXC l Receive clock RGRXC The receive clock is a continuous clock that provides the timing reference for receive operations The RGRXD and RGRXCTL signals are tied to this clock The clock is generated by the PHY and is 2 5 MHz at 10 Mbps operation 25 MHz at 100 Mbps operation and 125 MHz at 1000 Mbps operation RGRXDJ 3 0 l Receive data RGRXD The receive data pins are a collection of 4 data signals comprising 4 bits of data RGRDXO is the least significant bit LSB The signals are synchronized by RGRXC and valid only when RGRXCTL is asserted The lower 4 bits of data are received on the rising edge of the clock and the higher 4 bits of data are received on the falling edge of the RGRXC SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 23 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture 24 A TEXAS INSTRUMENTS www ti com Table 10 EMAC and MDIO Signals for RGMII Interface continued Description Signal Name UO RGRXCTL l RGMDCLK O R
231. ts the setting of bits 8 to 15 in the EW_INTCTL register Figure 18 shows the block diagram of transmit pacer and interrupt combiner TPIC TXEVT is an interrupt from EMAC Figure 18 Transmit Pacer and Interrupt Combiner Transmit pacer and interrupt combiner TXEVT 0 Pacing block EW_INTCTL 8 TXEVT 1 Pacing block ee EW_INTCTL 9 TXEVT 2 Pacing block ee EW_INTCTL 10 TXEVT 3 Pacing block ee EW_INTCTL 11 MACTXINT TXEVT 4 Pacing block EE EW_INTCTL 12 TXEVT 5 Pacing block EE EW_INTCTL 13 TXEVT 6 Pacing block IECH EW_INTCTL 14 TXEVT 7 Pacing block EW_INTCTL 15 PS_TICK EW_INTCTL 15 8 SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 45 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated EMAC Functional Architecture 2 7 5 Receive Pacer and Interrupt Combiner RPIC A TEXAS INSTRUMENTS www ti com The receive pacer and interrupt combiner RPIC block performs following functions Implements pacing for receive events Combines the output of the pacer module based on the settings of bits 16 to 23 in the EW_INTCTL register and generates a single MACRXINT interrupt per the C64x megamodule Receives a single PG TICK and forwards it to all the pacing blocks Allows per interrupt enabling or disabling of the interrupts the setting of bits 16 to 23 in the EW_INTCTL register Figure 19 shows the block diagram
232. ue has already been read If the pNext value has already been read the receiver will halt the receive channel in question and the software application may restart it at that time The software can detect this case by searching for an end of queue EOQ condition flag on the updated packet descriptor when it is returned by the EMAC 2 5 5 2 Buffer Pointer The buffer pointer is the byte aligned memory address of the memory buffer associated with the buffer descriptor The software application must set this value prior to adding the descriptor to the active receive list This pointer is not altered by the EMAC 2 5 5 3 Buffer Offset This 16 bit field must be initialized to zero by the software application before adding the descriptor to a receive queue This field will be updated depending on the RXBUFFEROFFSET register setting When the offset register is set to a non zero value the received packet is written to the packet buffer at an offset given by the value of the register and this value is also written to the buffer offset field of the descriptor When a packet is fragmented over multiple buffers because it does not fit in the first buffer supplied the buffer offset only applies to the first buffer in the list which is where the start of packet SOP flag is set in the corresponding buffer descriptor In other words the buffer offset field is only updated by the EMAC on SOP descriptors The range of legal values for the BUFFEROFFSET r
233. ular USERACCESS register MDIO user interrupt for a particular USERACCESS register is disabled if the corresponding bit is 0 Writing a 0 to this register has no effect SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 85 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS MDIO Registers www ti com 4 11 MDIO User Command Complete Interrupt Mask Clear Register USERINTMASKCLEAR The MDIO user command complete interrupt mask clear register USERINTMASKCLEAR is shown in Figure 38 and described in Table 31 Figure 38 MDIO User Command Complete Interrupt Mask Clear Register USERINTMASKCLEAR A 16 Reserved HO 15 2 1 0 Reserved Der R 0 R WC 0 LEGEND R Read only R WC Read Write 1 to clear n value after reset Table 31 MDIO User Command Complete Interrupt Mask Clear Register USERINTMASKCLEAR Field Descriptions Bit Field Value Description 31 2 Reserved 0 Reserved 1 0 USERINTMASKCLEAR MDIO user command complete interrupt mask clear for USERINTMASKEDf 1 0 respectively Setting a bit to 1 will disable further user command complete interrupts for that particular USERACCESS register Writing a 0 to this register has no effect 86 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incor
234. underrun Late collisions CRC errors carrier loss and underrun have no effect on this statistic SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 153 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 50 25 Transmit Carrier Sense Errors Register TXCARRIERSENSE The total number of frames on the EMAC that experienced carrier loss Such a frame is defined as having all of the following e Was any data or MAC control frame destined for any unicast broadcast or multicast address e Was any size e The carrier sense condition was lost or never asserted when transmitting the frame the frame is not re transmitted CRC errors and underrun have no effect on this statistic 5 50 26 Transmit Octet Frames Register TXOCTETS The total number of bytes in all good frames transmitted on the EMAC A good frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address e Was any length e Had no late or excessive collisions no carrier loss and no underrun 5 50 27 Transmit and Receive 64 Octet Frames Register FRAME64 The total number of 64 byte frames received and transmitted on the EMAC Such a frame is defined as having all of the following e Any data or MAC control frame that was destined for any unicast broadcast or multicast address
235. using the USERACCESSn register cause the ALIVE register to be updated The USERPHYSELn register is used to track the link status of any two of the 32 possible PHY addresses Changes in the link status of the two monitored PHYs sets the appropriate bit in the LINKINTRAW and LINKINTMASKED registers if they are enabled by the LINKINTENB bit in USERPHYSELn While the MDIO module is enabled the host can issue a read or write transaction over the management interface using the DATA PHYADR REGADR and WRITE bits in the USERACCESSn register When the application sets the GO bit in USERACCESSn the MDIO module begins the transaction without any further intervention from the CPU Upon completion the MDIO module clears the GO bit and sets the USERINTRAW 0 1 bit in the USERINTRAW register corresponding to the USERACCESSn used The corresponding USERINTMASKED bit in the USERINTMASKED register may also be set depending on the mask setting configured in the USERINTMASKSET and USERINTMASKCLEAR registers A round robin arbitration scheme schedules transactions that may be queued using both USERACCESSO and USERACCESS1 The application software must verify the status of the GO bit in USERACCESSn before initiating a new transaction to ensure that the previous transaction has completed The application software can use the ACK bit in USERACCESSn to determine the status of a read transaction 2 8 2 1 Initializing the MDIO Module To have the application software or
236. ved 7 0 RXFILTERTHRESH Receive filter low threshold These bits contain the free buffer count threshold value for filtering low priority incoming frames This field should remain 0 if no filtering is desired 122 C6472 TCI6486 EMAC MDIO SPRUEF8F March 2006 Revised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 27 Receive Channel 0 7 Flow Control Threshold Register RXnFLOWTHRESH The receive channel 0 7 flow control threshold register RXnFLOWTHRESH is shown in Figure 69 and described in Table 63 Figure 69 Receive Channel o Flow Control Threshold Register RXnFLOWTHRESH 31 Reserved HO 15 8 Reserved RXnFLOWTHRESH HO R W 0 LEGEND R W Read Write R Read only n value after reset Table 63 Receive Channel o Flow Control Threshold Register RXnFLOWTHREShH Field Descriptions Bit Field Value Description 31 8 Reserved 0 Reserved 7 0 RXnFLOWTHRESH Receive flow threshold These bits contain the threshold value for issuing flow control on incoming frames for channel n when enabled SPRUEF8F March 2006 Revised November 2010 C6472 TCI6486 EMAC MDIO 123 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 28 Receive Channel 0 7 Free Buffer Count Register
237. vice driver for Ethernet A device drive should follow this initialization procedure to get the EMAC to the state where it is ready to receive and send Ethernet packets Some of these steps are not necessary when performed immediately after device reset 1 If enabled clear the device interrupt enable in EW_INTCTL 2 Clear the MACCONTROL RXCONTROL and TXCONTROL registers not necessary immediately after reset 3 Initialize all 16 Head Descriptor Pointer registers RXNHDP and TXnHDP to 0 Clear all 36 statistics registers by writing O not necessary immediately after reset 5 Initialize all 32 receive address RAM locations to 0 Set up the addresses to be matched to the eight receive channels and the addresses to be filtered through programming the MACINDEX MACADDRHI and MACADDRLO registers 6 Initialize the RXnFREEBUFFER RXnFLOWTHRESH and RXFILTERLOWTHRESH registers if buffer flow control is to be enabled Program the FIFOCONTROL register if FIFO flow control is desired 7 Most device drivers open with no multicast addresses so clear the MACHASH1 and MACHASH2 registers 8 Write the RXBUFFEROFFSET register value typically zero 9 Initially clear all unicast channels by writing FFh to the RKUNICASTCLEAR register If unicast is desired it can be enabled now by writing the RXUNICASTSET register Some drivers will default to unicast on device open while others will not 10 If you want to transfer jumbo frames set the RXMAXLE
238. vised November 2010 Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated l TEXAS INSTRUMENTS www ti com EMAC Functional Architecture 2 5 3 To add a descriptor or a linked list of descriptors to an EMAC descriptor queue for the first time the software application writes the pointer to the descriptor or first descriptor of a list to the corresponding HDP register Note that the last descriptor in the list must have its next pointer cleared so that the EMAC can detect the end of the list If only a single descriptor is added its next descriptor pointer must be initialized to zero The HDP register must never be written to a second time while a previous list is active To add additional descriptors to a descriptor list already owned by the EMAC the NULL next pointer of the last descriptor of the previous list is patched with a pointer to the first descriptor in the new list The list of new descriptors to be appended to the existing list must itself be NULL terminated before the pointer patch is performed If the EMAC reads the next pointer of a descriptor as NULL in the instant before an application appends additional descriptors to the list by patching the pointer this may result in a race condition Thus the software application must always examine the Flags field of all EOP packets looking for a special flag called end of queue EOQ The EOQ flag is set by the EMAC on the last descriptor of a packet when
239. y the software application and is not altered by the EMAC 2 5 4 8 Ownership OWNER Flag When set this flag indicates that all the descriptors for the given packet from SOP to EOP are currently owned by the EMAC This flag is set by the software application on the SOP packet descriptor before adding the descriptor to the transmit descriptor queue For a single fragment packet the SOP EOP and OWNER flags are all set The OWNER flag is cleared by the EMAC once it is finished with all the descriptors for the given packet Note that this flag is valid on SOP descriptors only 2 5 4 9 End of Queue EOQ Flag When set this flag indicates that the descriptor in question was the last descriptor in the transmit queue for a given transmit channel and that the transmitter has halted This flag is initially cleared by the software application prior to adding the descriptor to the transmit queue This bit is set by the EMAC when the EMAC identifies that a descriptor is the last for a given packet the EOP flag is set and there are no more descriptors in the transmit list next descriptor pointer is NULL The software application can use this bit to detect when the EMAC transmitter for the corresponding channel has halted This is useful when the application appends additional packet descriptors to a transmit queue list that is already owned by the EMAC Note that this flag is valid on EOP descriptors only 2 5 4 10 Teardown Complete TDOWNCMPLT
240. yright 2006 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS EMAC Port Registers www ti com 5 46 Transmit Channel 0 7 DMA Head Descriptor Pointer Register TXnHDP The transmit channel 0 7 DMA head descriptor pointer register TXNHDP is shown in Figure 88 and described in Table 82 Figure 88 Transmit Channel n DMA Head Descriptor Pointer Register TXnHDP 31 16 TXnHDP R W x 15 0 TXnHDP R W x LEGEND R W Read Write n value after reset Table 82 Transmit Channel n DMA Head Descriptor Pointer Register TXnHDP Field Descriptions Bit Field Value Description 31 0 TXnHDP Transmit channel n DMA Head Descriptor pointer Writing a transmit DMA buffer descriptor address to a head pointer location initiates transmit DMA operations in the queue for the selected channel Writing to these locations when they are nonzero is an error except at reset Host software must initialize these locations to zero on reset SPRUEF8F March 2006 Revised November 2010 144 C6472 TCI6486 EMAC MDIO Submit Documentation Feedback Copyright 2006 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com EMAC Port Registers 5 47 Receive Channel 0 7 DMA Head Descriptor Pointer Register RXnHDP The receive channel 0 7 DMA head descriptor pointer register RXNHDP is shown in Figure 89 and described in Table 83 Figure 89 Receive Channel n DMA Head Descriptor Poin

Texas Instruments TMS320TCI6486 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents