Telular SX4e TDMA User's Manual
Contents
1. ered invalid The factory default is 0 SOC disable defines whether the SID or SOC takes priority when classifying a service provider When the SOC disable value is set to 0 the highest priority classification of either the SID or SOC will take precedence when set to 1 the SID priority will take precedence If the SOC disable value is not in the range 0 or 1 it is considered invalid The factory default is 0 Band Order System Selection The following key sequence is used to enter the preferred band order Press 7 lt band order gt The band order value is a series of digits between 1 and 2 1 and 8 for Tri Mode model that must be at least 1digit and not more than 2 digits 8 digits for Tri Mode model long The following table describes the relationship between the band order digits and EIA TIA 136 system band assignment Band Order Digits EIA TIA 136 Band D 1900 MHz Band E 1900 MHz Band F 1900 MHZ 1 System A 800 MHz 2 System B 800 Miz TOMA 809 moge 3 Digital Band A 1900 MHz 4 Tri Mode Band B 1900 MHz 5 model Band C 1900 MHz 6 7 8 The factory default is 12 for the TDMA 800 model and 34125678 for the Tri Mode model Post Receiver Off Hook Option The following key sequence is used to enter the post receiver off hook option Press 9 lt post ROH option gt The post ROH value is set to 0 for continuous ROH tone 1 to disable ROH tone and periodically check for an on hook condition2. Band Order Digits EIA TIA 136 Band D 1900 MHz Band E 1900 MHz Band F 1900 MHZ 1 System A 800 MHz 2 System B 800 MHz TDMA On inoue 3 Digital Band A 1900 MHz 4 TriMode Band B 1900 MHz 5 model Band C 1900 MHz 6 7 8 The factory default is 12 for the TDMA 800 model and 34125678 for the Tri Mode model 7 Hang up the phone The flashing LED indicator will become solid GREEN Phone Number Setup is complete SX4e TDMA 800 e SX4e Tri Mode 7 Technical Manual PHONECELL SX4e OPERATION How to Use the LED Status Indicators 5 e Plug in the power supply e Wait for the unit to initialize e The three LED indicators on the front of your Phonecell will turn ON The Tables below describe the modes and operation of the three indicators see Figures 9 and 10 LED 1 Power Status Indicator LED Color LED Activity Description GREEN FWT Power ON ORANGE Low Voltage Detection NONE Dark No FWT Power LED 2 Cellular Status Indicator LED Color LED Activity Description GREEN Good Cellular Signal Strength GREEN Flashing Poor Cellular Signal RED No Cellular Service Figure 9 LED status indicators Contact your service provider to verify that cellular service is activated LED 3 FWT Status Indicator LED Color Description GREEN Normal Operation GREEN Flashing Normal Operation Analog Fax Call GREEN RED Alternating Programming Mode RED FWT Failure RED Flashing Phone or Fax Inter
3. From 20 C 4 F to 60 C 140 F Up to 95 relative humidity non condensing IMPORTANT To ensure safe and efficient operation please read the following information and observe these guidelines whenever using your Phonecell SX4e WARNING Only Authorized Service Personnel should remove the cover of your Phonecell For further assis tance contact your Authorized Telular Representative Please have the model and serial number ready model and serial numbers are located on the label on the bottom of the unit Your Phonecell SX4e FWT Fixed Wireless Terminal functions as both a radio transmitter and receiver When it is ON the FWT receives and sends out radio frequency RF energy The Phonecell SX4e 800 operates in the frequency ranges of between 824 MHz and 894 MHz The Phonecell SX4e Tri Mode operates in the frequency ranges of between 824 MHz and 894 MHz Digital TDMA and analog AMPS and between 1850 MHz and 1990 MHz Digital PCS It employs commonly used phase frequency modu lation techniques When you use your Phonecell SX4e the cellular system handling your call controls the power level at which your unit transmits Exposure to RF Radio Frequency Energy In 1991 the Institute of Electrical and Electronics Engineers IEEE and in 1992 the American National Standards Institute ANSI updated the 1982 ANSI Standard for safety levels with respect to human expo sure to RF energy After reviewing the available body of rese
4. incurred in returning Product for warranty service to Telular s Repair Center j Repair programming or servicing by someone other than Telular SX4e TDMA 800 e SX4e Tri Mode 22 Technical Manual V GENERAL PROVISIONS THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS OR STATUTORY WARRANTIES IMPLIED WAR RANTIES INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE TITLE INFRINGEMENT DELIVERY NEGLIGENCE AND PERSONAL INJURY ARE DIS CLAIMED FURTHER AS THE CELLULAR CARRIER IS NOT CONTROLLED BY TELULAR NO WARRANTY IS MADE AS TO COVERAGE AVAILABILITY OR GRADE OF SERVICE PROVIDED BY THE CELLULAR CARRIER IN NO EVENT SHALL TELULAR BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT FOR ANY LOSS OF USE LOSS OF TIME INCONVENIENCE COMMERCIAL LOSS LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW SOME J URISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS VI SOFTWARE PROVISIONS Laws in the United States and other countries preserve for Telular certain exclusive rights for copyrighted Telular software such as the exclusive rights to reproduce in copies and distribute copies of such Telular software Telular software may be copied into used in an
5. steady dial tone ROH Receiver Off Hook Tone If the telephone equipment remains off hook off its cradle with no dialing activity for 30 seconds the receiver emits an ROH tone for 45 seconds Incoming Call Alert If you re dialing a number and an incoming call occurs the receiver will emit an audible ring To answer the incoming call e Press the HOOKFLASH button once This will connect the incoming call e OR hang up immediately This will cause the phone to start ringing Roam Dial Tone When cellular service is available but the SX4e is in a Roam area the receiver may emit a different dial tone to indicate the roaming condition However unless the FWT is repro grammed in the field the factory default tone is set the same as normal service dial tone How to Adjust the Volume Level If the volume level on your phone is too high or too low you can adjust the levels using the keypad on your telephone Note your telephone must be in Tone Dial DTMF mode to adjust the levels To Increase Audio Level Increase the audio level in steps by pressing Press 8 also known as Up Continue to press 8 until the desired level is reached To Decrease Audio Level Decrease the audio level in steps by pressing Press 3 also known as Down Continue to press 3 until the desired level is reached NOTE The default setting lets you adjust the audio up to three 3 steps from the default volume i
6. Phonecell SX4 model has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules Changes or modifications not expressly approved by Telular Corporation will void your authority to operate the equipment per FCC part 15 paragraph 15 21 These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the antenna e Increase the separation between the equipment and the terminal Connect the equipment into an outlet on a circuit different from that to which the terminal is connected e Consult your Authorized Telular Distributor or an experienced radio TV technician for help SX4e TDMA 800 e SX4e Tri Mode 21 Technical Manual IMPORTANT NOTICES CONTINUED WARRANTY WHAT THIS WARRANTY COVERS AND FOR HOW LONG TELULAR CORPORATION Telular warrants to a distributor Buyer or to a cust
7. et E ro by means of an 18 gauge or heavier insu safety ground r J lated wire The wire insulation should be terminal screw a green with a yellow stripe to indicate that m this is a protective earth safety ground connection see Figure 5 Figure 5 Protective earth terminal screw Connect the Line Cord from the AC power source to the Power Supply Connect the barrel plug on the Power Supply to the Power Input port marked DC Input on the side of the SX4e NOTE An optional battery back up unit not supplied may be used instead of the Power Supply see Figure 6 Follow the battery installation instructions provided with the Backup Unit 4 The LED Power Status indicator located on the front of the FWT will turn green immediately upon connecting to power T 2 Power DC INPUT Port Optional Batey ee Backup Unit zy Line Cord eo o lt AC Power Figure 6 Connect the SX4e to power SX4e TDMA 800 e SX4e Tri Mode 5 Technical Manual Plug in Your Telephone 1 Locate the modular line port on your phone and plug in one end of a standard phone cord 2 Connect the other end of the cord to the telephone port on the side of your SX4e see Figure 7 NOTE An Ru 11 connector will fit into the phone port NOTE The SX4e does not support direct computer modem data operation through the phone port or fax port See the Digital Data Service section of this manual for computer digital data operati
8. information fixed at midnight January 1 Contact your service provider to activate Caller ID FAX AND DATA TRANSMISSION Fax and Data Applications When considering using a device other than a telephone in conjunction with the Phonecell SX4e such as a modem consider if that device would plug directly into the Fax jack on the premise and work with a normal telephone line If the answer is yes you can use that device with the Phonecell SX4e if the answer is no that device will most likely not work in this application Multi extension installations For a multi extension installation make sure that all the extensions are on hook If one extension is off hook not hung up none of the extensions on that line will ring when a call is being received Facsimile Machines A facsimile machine needs to be connected exactly as it needs to be configured for use on a regular wired telephone company line Some models of portable facsimile machines require an external telephone for normal operation These models still need this external telephone when hooked up to the Phonecell SX4e A splitter may be required Fax and Data Transmission Overview The Phonecell SX4e operates on TDMA 800 MHz and PCS 1900 MHz digital networks and on AMPS 800 MHz analog networks Because most TDMA and PCS networks do not support digital fax and data services AMPS 800 MHz networks and AMPS 800 MHz channels on TDMA 800 MHz net works can be used for fax and data s
9. invalid The lt cas_pls_duration gt value is programmed in 1 ms increments from 10 to 65535 10 65 535 ms If the value is not between 10 and 65535 inclusive it will be considered invalid The cas_pls_level can be programmed to any of the values shown in the table below If the cas_pls_level is not between 0 and 6 inclusive it will be considered invalid The factory default is 0 0 100 and 3 Line Reversal Outgoing Option The following key sequence is used to enable or disable line tip ring reversal for outgoing calls Press 22 lt line_reversal_outgoing gt The line reversal outgoing value is set to 0 to disable line reversal 1 to enable line reversal If the value is neither 0 nor 1 it is considered invalid The factory default is 0 Line Reversal Incoming Option The following key sequence shall be used to enable or disable line tip ring reversal for incoming calls Press 23 lt line_reversal_incoming gt The line reversal incoming value is set to 0 to disable line reversal 1 to enable line reversal If the value is neither 0 nor 1 it is considered invalid The factory default is 0 A Key The following key sequence is used to enter the A Key Press 27 lt A Key gt If the A Key is less than 6 digits or more than 26 digits it is considered invalid and the FWT will not update or store this value the currently stored value will remain On Hook Call Alert Cadence Option The following key sequence wil
10. the Received Signal Strength Indicator RSSI LED on the unit See the How to Use the LED Status Indicators section of this guide 1 Connect the antenna to the SX4e see Figure 1 2 Finger tighten the antenna do not over tighten Standard Antenna TNC Antenna Connector Figure 2 For optimum signal strength locate the unit near a window with the antenna pointed upward Figure 1 SX4e antenna installation Optional Wall Mount Installation After you ve selected a location and made all the necessary connections and adjustments your SX4e is ready for wall mounting 1 To mount the Phonecell SX4e on a wall mark two hole locations 166 mm 6 17 32 inches apart These hole locations match the mounting hooks on the back of the unit see Figure 3 2 Install the screws not supplied leaving a gap approximately 3mm 1 8 inches between screw head and wall E 3 Mount the FWT onto the screws see Figure 4 166 mm 6 17 32 inches a _ i a a7 a Figure 3 Mounting hooks for Figure 4 Mount the SX4e onto the screws in optional wall mounting the wall SX4e TDMA 800 e SX4e Tri Mode 4 Technical Manual Connect Your SX4e to AC Power 1 A protective earth safety ground terminal ie screw marked with this protective earth O fhaa aa symbol is provided on the back of the SX4e irks i OE Phonecell unit Connect this terminal to a Kia ma T good earth ground i e a cold water pipe Protective earth
11. the air Children Do not allow children to play with your Phonecell SX4e to prevent damage to the unit Blasting Areas Construction crews often use remote control RF devices to set off explosives Therefore to avoid interfering with blasting operations turn your Phonecell SX4e OFF when in a blasting area or in areas posted Turn off two way radio Potentially Explosive Atmospheres Turn your Phonecell OFF when in any area with a potentially explosive atmosphere It is rare but your Phonecell or its accessories could generate sparks Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death Areas with a potentially explosive atmosphere are often but not always clearly marked They include fueling areas such as gas stations below deck on boats fuel or chemical transfer or storage facilities areas where the air contains chemicals or particles such as grain dust or metal powders and any other area where you would normally be advised to turn off your vehicle engine Do not transport or store flammable gas liquid or explosives in the area of your Phonecell or acces sories Vehicles using liquefied petroleum gas such as propane or butane must comply with the National Fire Protection Standard FPA 58 For a copy of this standard contact the National Fire Protection Association One Batterymarch Park Quincy MA 02269 Attn Publications Sales Division FCC Part 15 Class B Compliance This
12. If the post ROH value is neither 0 nor 1 it is considered invalid The factory default is 1 System Operator Code The following key sequence is used to program the system operator code Press 77 lt code gt If the code value is not in the range of 0 to 4 095 it is considered invalid The factory default is 0 Emergency Numbers The following key sequence is used to program the emergency numbers Press 78 lt index gt lt emergency number gt The index is a number from 1 to 3 representing the emergency number to be programmed If the emergency number is less than 3 digits or more than 10 digits it is considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default is an emergency number of 911 in index 1 indices 2 and 3 are not programmed SX4e TDMA 800 e SX4e Tri Mode 15 Technical Manual Call Answered Supervision Pulse Option The following key sequence is used to enable or disable the call answered supervision pulse select its frequency and program its duration Press 18 lt cas_ pls enable gt lt cas_ pls freq gt lt cas_pls_duration gt x lt cas_pls_level gt The lt cas_pls_enable gt value is set to 0 to disable the pulse 1 to enable the pulse If the value is neither 0 nor 1 it will be considered invalid The lt cas_pls_frequency gt value is set to O for 12 kHz 1 for 16 kHz If the value is neither O nor 1 it will be considered
13. NS INCLUDING WARRANTY DISCLAIMERS LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS DO NOT USE THE PRODUCT AND IMMEDIATELY RETURN THE UNUSED PRODUCT FOR A COMPLETE REFUND You agree to accept sole responsibility for any misuse of the Product by you and in addition any negligent or illegal act or omission of your or your agents contractors servants employees or other users of the Product so long as the Product was obtained from you in the use and operation of the Product INDEMNIFICATION OF TELULAR CORPORATION TELULAR YOU SHALL INDEMNIFY DEFEND AND HOLD HARMLESS TELULAR FOR ANY OF THE COST INCLUDING REA SONABLE ATTORNEYS FEES AND FROM CLAIMS ARISING OUT OF YOU YOUR CLIENTS OR OTHER THIRD PARTIES USE OR OPERATION OF THE PRODUCT i FOR MISUSE OR IN A MANNER NOT CONTEMPLATED BY YOU AND TELULAR OR INCONSISTENT WITH THE PROVISIONS OF THIS MANUAL ii IN AN ILLEGAL MANNER OR AGAINST PUBLIC POLICY iii INA MANNER SPECIFICALLY UNAUTHORIZED IN THIS MANUAL iv INA MANNER HARMFUL OR DANGEROUS TO THIRD PARTIES v FROM CLAIMS BY ANYONE RESPECTING PROB LEMS ERRORS OR MISTAKES OF THE PRODUCT OR vi COMBINATION OF THE PRODUCT WITH MATERIAL MODIFICATION OF THE PRODUCT OR USE OF THE PRODUCT IN AN ENVIRONMENT NOT PROVIDED OR PER MITTED BY TELULAR IN WRITING THE PARTIES SHALL GIVE EACH OTHER PROMPT NOTICE OF ANY SUCH COST OR CLAIMS AND COOPERATE EACH WITH THE OTHER TO EFFECT
14. TS WHEN THE PRODUCT IS USED IN CONJ UNCTION WITH ANCILLARY OR PERIPHERAL EQUIPMENT NOT MANU FACTURED BY TELULAR TELULAR DOES NOT WARRANT THE OPERATION OF THE PRODUCT PERIPHERAL COMBINATION AND TELULAR SHALL HONOR NO WARRANTY CLAIM WHERE THE PRODUCT IS USED IN SUCH A COMBINATION AND IT IS DETERMINED BY TELULAR THAT THERE IS NO FAULT WITH THE PRODUCT TELU LAR DISCLAIMS LIABILITY FOR RANGE COVERAGE AVAILABILITY OR OPERATION OF THE CELLULAR SYS TEM WHICH IS PROVIDED BY THE CARRIER IV WHAT THIS WARRANTY DOES NOT COVER a Subsequent upgrades and enhancements to the Product b Defects non compliance or damage resulting from use of the Product in other than its normal and customary manner or environment c Defects noncompliance or damage from mis use lightening accident or neglect d Defects noncompliance or damage from improper testing operation maintenance installation adjustment or any alteration or modification of any kind e Product disassembled or repaired in such a man ner as to adversely affect performance or prevent adequate inspection and testing to verify any warranty claim f Product which has had the serial number removed or made illegible g Defects non compliance or damage due to spills of food or liquid h All plastic surfaces and all other externally exposed parts that are scratched or damaged due to customer normal use i Costs and expenses including without limitation handling labor and transportation
15. UATE THIS INDEMNIFICATION DEFENSE AND HOLD HARMLESS TELULAR CORPORATION Corporate Headquarters 647 North Lakeview Parkway Vernon Hills Illinois 60061 USA Technical Support USA 1 800 TELULAR 1 800 835 8527 Tel 847 247 9400 Fax 847 247 0021 E mail support telular com http www telular com Part Number 56024002 2002 Telular Corporation All Rights Reserved SX4e TDMA 800 e SX4e Tri Mode 2 Technical Manual TABLE OF CONTENTS Safe Operation Instructions cc eceecceeeeeeeceeeeeeeeeeeeeeaeeeeaeeeeeeeaeeseeeeeaeeseaeeeneesaas 2 Important Notices nnan aches ct iri ashe seater aE E EE e TNE 2 Technical Support eirinen eects eee a aaa Nea ie en era nie 2 Installation iji s css Rose A ed eee eas 4 Antenna Location and Setup cecceesceseseeseeeeeeeceeeeeaeeseeeeeaceseaeesaeeseaeeeeeseaeeeneetenees 4 Optional Wall Mount Installation cececceeeeeeeeeeeeeeeeeeeeneeeeeeseeeeeneeseaeeseeeeeeseeeeeaees 4 Connect Your SX4e to AC POWED ecceeeceeseeeeeeceneeceeeeeeeseaeeeaeeseaeesieeseaeesieeeeaeeenetens 5 Plug in Your Telephone eniin a aparece ate tiene eaa ee 6 How to Set Up Your Phone Number ceecceesceseceeeeeeeeeeeeeeseeeeeaeeseeeeeeeeeneenaees 7 Phonecell SX4e Operation c ceccceecceseeeeeceneeceeeeeaeeseaeeeaeeseaeesseeseaeessaeeeeeseeeeeaees 8 How to Use the LED Status Indicators eeceeceeeeeeeeeeeneeeeeeeeeeeseaeeeeeseaeeseeeenaeetias 8 How to Place
16. Zero Dial Delay option gt Enter 0 to disable Zero Dial Delay option 1 to enable Zero Dial Delay option Enter either 0 or 1 otherwise the Phonecell will not update or store this value the existing stored parameter will remain The factory default setting is 1 Audio Output Level Control Use the following key sequence to program the nominal audio output level Press 69 lt output level gt The output level value is set to 0 for low 1 for normal and 2 for high If the output level value is greater than 2 it will be considered invalid The factory default is 1 Caller ID Format Selection The following key sequence is used to enter the Caller ID format selection Press 84 lt CID format gt The CID format value is set to 0 to select a CID Multiple Data Message Format MDMF with no date or time information set to 1 to select a CID MDMF with date and time information fixed at mid night January 1 set to 2 to select a CID Single Data Message Format SDMF with date and time information fixed at midnight January 1 If the CID format value is greater than 2 it is considered invalid The factory default is 0 SX4e TDMA 800 e SX4e Tri Mode 13 Technical Manual PHONECELL SX4e TECHNICIAN PROGRAMMING COMMANDS IMPORTANT The Phonecell SX4e is capable of over the air activation P lease contact your local cellular serv ice provider for more information IMPORTANT The following commands may be used by a trained service te
17. a Callll csr sicece occ sti saze ceases Sasceaaanes E E AE 8 How to Receive a Cale erince iyeon leas pease reas eee 8 How to End a Calli aca ha d ci tanec ila RAs ie a Ea 8 The Hookflash FUNCHON roienc ities sear Roisin Aisa nese eee 8 How to Use the Hookflash Function eeecceesseeeeeneeeeeeneeeseeeeeeneeeeeeaeeeseeeeeeneeeeees 8 Important Tones and Alerts 0 eee eeseeeeseeeeeeneeeeeneeeeeaeesesaeeeceaeeeeesaeeseeaeeeseeeeeseateteaes How to Adjust the Volume Level Variable Dial Time Auto Send Delay Option cecceeeceeseeeeeeeeneeseeeeeneeteeeeeeeeeaees 9 In Call DTMF Signalling Option cceeeeeceseseeeeeeeneeeeeeeeeeeeeeseeeeseeseaeesneeeeeeseeeeaees 9 Supplementary Services Network Dependent cccceeceeeeeeeeeeentetseeeeeetaes 9 Call Wait ceca Ste 6 Sick atl ha n aa Se ates cise Hs geen chan a tes oe SO 9 Three Way Galing ici ctsset cccek ices ct cen hcvebeesa ces ecszess aasa aana Taaa akaa a Eora Eai aa anera ESE 9 Gall oane tae ala EE T E A A E E 9 EET a DIETE E E A oe A A E E A EE 10 Fax and Data Transmission cccceeeeeneeeeeeeeeeeeeeeeeneeesenneeeeeaeeeeeaeesenaeeeseneeeee 10 Fax and Data Application Sis noresite a aa a i 10 Originating Fax and Data Calls ceccecceeeeeceeeeeeneeeeeeeeeeeseeeeeeeeeeeseaeeseeteaeeseeeenaees 11 Receiving Fax and Data Callls ceecceeeceeseeeeeeceaeeeeeeeeeeeceaeeeaeeseeeeeeeeeaeesieeseeeeneeees 11 Phonecell SX4e User Setup
18. ar dealer or service provider to determine the availability of an analog channel Moisture or Ventilation Problems Visually inspect your Phonecell unit s enclosure Moisture can damage the equipment Ventilation is also very important If there are moisture or ventilation problems move your Phonecell to correct as necessary see the Temperature Environment section of this manual No Power The top LED lamp on the front of your Phonecell SX4e indicates the unit s power condition If the LED is ORANGE or GREEN your Phonecell is receiving power If the power cord is connected and the LED lamp is not lit the Phonecell is not receiving power Verify that the AC power source and its corresponding circuit breaker are functioning properly Battery Backup Failure If you re using the optional Battery Backup Unit the unit must be connected to AC power for at least 24 hours to fully charge the batteries before they ll provide back up power to your Phonecell Verify that the batteries have been charged for at least 24 hours and that the power source and its corre sponding circuit breaker are functioning properly Then examine the batteries for physical damage and corrosion Replace the batteries if necessary SX4e TDMA 800 e SX4e Tri Mode 19 Technical Manual GENERAL INFORMATION AND SAFETY Temperature Environment Operating Temperature From 10 C 14 F to 50 C 122 F Up to 95 relative humidity non condensing Storage Temperature
19. arch more than 120 scientists engineers and physicians from universities government health agencies and industry developed this updated Standard In March 1993 the U S Federal Communications Commission FCC proposed the adoption of this updated Standard The design of your Telular Phonecell SX4e complies with this updated Standard Of course if you want to limit RF exposure even further than the updated ANSI Standard you may choose to control the duration of your calls and operate your phone in the most power efficient manner Safe Operation Requirement Do not operate your Phonecell SX4e when any person is within 203 mm 8 inches of the antenna Antenna Care and Replacement Do not use the Phonecell SX4e with a damaged antenna If a damaged antenna comes into contact with the skin a minor burn may result Have your antenna replaced by a qualified technician immediately Use only a manufacturer approved antenna Unauthorized antennas modifications or attachments could dam age the Phonecell SX4e Driving Check the laws and regulations on the use of cellular products in the areas where you drive Some juris dictions prohibit your using a cellular device while driving a vehicle Even if your jurisdiction does not have such a law we strongly suggest that for safety reasons the driver use extreme caution when operating the cellular device while the vehicle is in motion Always obey the law Exposure to Electronic Devices Most modern ele
20. cccccecccceeceeeeceneeeeeeeeeeeseaeseaeeeeeeeaeeseeeeeeeseaeeeeeeeas 12 How to Enter the User Setup Mode cccceesceeseeeeeeeeeeeeeneeseeeeeeeseaeeeaeessaeeneeeenaten 12 User Setup Commands Serisinin aeaaee aee sii 12 In Call DTMF Signalling Option ceeceeeceseeeeeeeeeeeeeeeeeseeeeeeeseeeeseeseaeeeieeseaeesseeeeas 12 Auto Send Delay Pulse Dial Option Enable Disable Zero Dial Delay for Frequently Called Numbers cceeseeeeeee 13 Audio Output Level Controls apesin iiion oeiee iveene ia asan iiS oa 13 Caller ID Format Selection ccceeceeeeeesceeeeeeseeteaeeeeeeceaeeseeeseaeessaeeeaeessaeseeeeeaeeeaees 13 Phonecell SX4e Technician Programming Commands ccsecceeeeeeeeeeeeeeees 14 Phonecell SX4e Troubleshooting cceecceeeceeeceeeeeeseeeeeeeeeeeeeeesneeeeneeseaeeeneeeas 19 General Information and Safety 00 0 0 cece ceeeeeeeeeneeeeaeeeeeeeeaeeseeeeeaeeteaeeeeeeteaten 20 Wairanty 255 25 eceeees cos cede e cali Sis ea ra aae cece eda ch ca env ar a oe os ned dela th OE ae aN 22 SX4e TDMA 800 e SX4e Tri Mode 3 Technical Manual INSTALLATION Antenna Location and Setup The Phonecell SX4e comes with a standard spike antenna See Figure 1 The Phonecell SX4e comes with a standard spike antenna TNC For optimal signal strength choose an antenna loca tion that is above ground and as close to windows or exterior walls as possible See Figure 2 Cellular signal strength is displayed by
21. chnician to change the configuration of the Phonecell FWT WARNING These commands are intended for use by trained service technicians only Untrained users could damage the Phonecell violate local regulations and breach the service agreement with the cellular provider For further assistance please contact your Authorized Telular Representative How to Enter the Technician Programming Mode Use the following access code to enter the Technician Programming mode Press 0 12344321 The access code is 8 digits If the access code is not 8 digits or does not match the access code the Programming mode cannot be entered This code is pre programmed during production and cannot be changed in the field If you enter the access code correctly the dial tone should change to a different steady Programming tone and the bottom LED indicator on the front of the Phonecell will blink alternately RED and GREEN to indicate that you re in the programming mode Mobile Identification Number MIN The following key sequence is used to enter the FWT phone number Press 1 lt MIN gt If the MIN phone number value is not 10 digits it is considered invalid and the FWT will not update or store this value the currently stored value will remain Access Overload Class ACCOLC The following key sequence is used to enter the ACCOLC Press 2 lt ACCOLC gt If the ACCOLC is not in the range of 0 to 15 it is considered invalid The factory
22. ctronic equipment is shielded from RF energy However RF energy from cellular devices may affect inadequately shielded electronic equipment RF energy may affect improperly installed or inadequately shielded electronic operating and entertainment systems in motor vehicles Check with the manufacturer or its representative to determine if these systems are adequately shielded from external RF energy You should also check with the manufacturer of any equipment that has been added to your vehicle Consult the manufacturer of any personal medical devices such as pacemakers hearing aids etc to determine if they are adequately shielded from external RF energy Turn your Phonecell SX4e OFF in health care facilities when any regulations posted in the areas instruct you to do so Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy SX4e TDMA 800 e SX4e Tri Mode 20 Technical Manual Aircraft Turn OFF your Phonecell SX4e before boarding any aircraft e Use it on the ground only with crew permission e Do not use it in the air To prevent possible interference with aircraft systems U S Federal Aviation Administration FAA regulations require you to have permission from a crew member to use your cellular phone or any other cellular product while the plane is on the ground To prevent interference with aircraft sys tems FCC regulations prohibit using your cellular device while the plane is in
23. d redistributed with only the Product associated with such Telular software No other use including without limitation disassembly of such Telular software or exercise of exclusive rights in such Telular software is permitted and Telular reserves all rights not expressly granted in this Limited Commercial Warranty Patents Telular Corporation products are protected and manufactured under one or more of the following U S patents and related international patents and patents pending relating thereto 4 658 096 4 737 975 4 775 997 4 868 519 4 922 517 5 134 651 5 361 297 5 469 494 5 046 085 5 715 296 Trademarks Telular Corporation owns the following registered trademarks TELULAR and design TELULAR CELJACK MAXJACK TELCEL HEXAGON LOGO PHONECELL CELSERV TELGUARD CPX and AXCELL SX4e TDMA 800 e SX4e Tri Mode 23 Technical Manual ee eee TELULAR 2 647 North Lakeview Parkway Vernon Hills Illinois 60061 USA USA 1 800 TELULAR 1 800 835 8527 Tel 847 247 9400 Fax 847 247 0021 E mail support telular com http www telular com 06 11 02 Part Number 56024002
24. d users cannot submit items to Telular under this warranty To receive warranty service an RMA number must first be obtained from Telular Technical Support The defective or non compliant Product should be sent by Buyer freight pre paid to Telular Corporation 647 North Lakeview Parkway Vernon Hills IL 60061 USA or other designated location The product must be packaged in the original carton and packing material or an equivalent package and must have the assigned RMA number clearly marked on the carton Returned Product received without an RMA num ber will be returned to the sender Ill WARRANTY CONDITIONS This is the complete warranty for the Products manufactured by Telular and sold to Buyer Telular assumes no obligation or liability for additions or modifications to this warranty unless made in writing and signed by an officer of Telular Unless made in Separate written agreement between Telular and Buyer Telular does not warrant the installation field maintenance or serv ice of the Products or parts TELULAR CANNOT BE RESPONSIBLE IN ANY WAY FOR ANY ANCILLARY EQUIPMENT NOT FURNISHED BY TELULAR WHICH IS ATTACHED TO OR USED IN CONNECTION WITH THE PRODUCTS OR FOR OPERATION OF THE PRODUCTS WITH ANY ANCILLARY EQUIPMENT AND ALL SUCH EQUIPMENT IS EXPRESSLY EXCLUDED FROM THIS WARRANTY FURTHERMORE TELULAR CANNOT BE RESPONSIBLE FOR ANY DAMAGE TO THE PRODUCTS RESULTING FROM THE USE OF ANCILLARY EQUIPMENT NOT FURNISHED BY TELULAR FOR USE WITH THE PRODUC
25. dary A Side Non Standard Control Channel Option The following key sequence is used to select the non standard secondary control channel range for A side AMPS systems Press 91 lt first ACC gt lt last ACC gt The first ACC and last ACC values must be in the range of 0 799 or 991 1023 If the value is not in the range it will be considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default for first ACC is 708 and for last ACC is 688 Secondary Control Channel Option The following key sequence is used to select the non standard secondary control channel range for B side AMPS systems Press 92 lt first ACC gt lt last ACC gt The first ACC and last ACC values must be in the range of 0 799 or 991 1023 If the value is not in the range it will be considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default for first ACC is 737 and for last ACC is 757 Secondary Paging Channel Option The following key sequence is used to select the secondary paging channel AMPS systems Press 93 lt paging chan gt The paging channel value must be in the range of 0 799 or 991 1023 If the value is not in the range it will be considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default for is 708 SX4e TDMA 800 e SX4e Tri Mode 18 Techn
26. default is 2 First Paging Channel The following key sequence is used to set up the first paging channel Press 4 lt paging channel gt If the paging channel is not in the range of 1 to 1023 it is considered invalid Channels 800 to 990 are invalid The factory default channel setting is 333 Home System Identification SID The following key sequence is used to enter the home SID Press 5 lt SID gt If the SID value is not in the range of 0 to 32 767 it is considered invalid The factory default is 69 Dial Tone After Remote On Hook Option The following key sequence is used to enter the dial tone after remote on hook option Press 8 lt dial tone option gt The dial tone value is set to 0 for no tone after a remote on hook 1 to enable dial tone after remote on hook If the value is neither 0 nor 1 it is considered invalid The factory default is 1 SX4e TDMA 800 e SX4e Tri Mode 14 Technical Manual Roam Option The following key sequence is used to enter the roam option Press 6 lt home only gt lt SOC disable gt When the home only value is set to 0 the Phonecell will use the SOC SID list specified in the IRDB along with the home SID and home SOC when searching for service and will search for the highest priority service provider that is not forbidden When the home only value is set to 1 the Phonecell will use only the home SID and home SOC If the home only value is not set to 0 or 1 it is consid
27. during a particular call Contact your service provider to activate Call Waiting Three Way Calling Three Way Calling enables you to set up a three way conversation with two other different numbered users Contact your service provider to activate Three Way Calling Call Forwarding Call Forwarding enables you to forward all your incoming calls to another phone number even if your telephone is turned off You can continue to make calls from your telephone when Call Forwarding is activated Contact your service provider to activate Call Forwarding SX4e TDMA 800 SX4e Tri Mode 9 Technical Manual Caller ID The Phonecell SX4e sends information to an external Caller ID device to allow presentation of the calling party s telephone number if this service is available from the network Caller ID boxes in compliance with ETSI 300 659 or Bellcore GR 30 CORE standards are supported Only type 1 on hook presentation is supported Because there is no source of date and time available to the FWT the displayed date and time will be arbitrary Three Caller ID message formats are available to satisfy the requirements of currently available Caller ID devices e Multiple Data Message Format MDMF with blank date and time fields this selection will work for most currently available caller ID devices e Multiple Data Message Format MDMF with date and time information fixed at midnight January 1 e Single Data Message Format SDMF with date and time
28. e that you re in the programming mode USER SETUP COMMANDS In Call DTMF Signaling Option Use the following key sequence to set the In Call DTMF Signaling option Press 10 lt In Call DTMF option gt The lt gt brackets represents the 1 digit in call DTMF signaling option Enter 0 for In Band Signaling 1 for Out of Band Signaling 2 for both In Band and Out of Band signaling 3 for neither Enter a value between 0 and 3 otherwise the FWT will not update or store this value the existing stored parameter will remain The factory default setting is 1 Out of Band signaling Auto SEND Delay Use the following key sequence to set the Auto SEND Delay Press 11 lt Auto SEND Delay gt Enter a value between 2 and 20 seconds otherwise the Phonecell will not update or store this value the existing stored parameter will remain The factory default setting is 3 seconds Pulse Dial Option Use the following key sequence to set the Pulse Dial option Press 12 lt Pulse Dial option gt Enter 0 to disable pulse dialing capability 1 to enable pulse dialing capability Enter either 0 or 1 otherwise the Phonecell will not update or store this value the existing stored parameter will remain The factory default setting is 1 SX4e TDMA 800 e SX4e Tri Mode 12 Technical Manual Enable Disable Zero Dial Delay for Frequently Called Numbers Use the following key sequence to set the Zero Dial Delay option Press 21 lt
29. ectly you ll hear 3 short tones followed by the programming tone If correct you ll hear the programming tone again If the MIN phone number value is not 10 digits it is considered invalid and the FWT will not update or store this value the currently stored value will remain 4 Press 5 lt SID gt This key sequence is used to enter the 1 to 5 digit System Identifier or SID This information identifies your cellular service company If you enter the SID incorrectly you ll hear three short tones followed by the programming tone if correct you ll hear the programming tone again If the SID value is not in the range of 0 to 32 767 it is considered invalid The factory default is 69 5 Press 4 lt paging channel gt This key sequence is used to set up your 1 to 4 digit initial paging channel When you turn on your Phonecell this channel helps the service provider find you and vice versa If the paging channel is not in the range of 1 to 1023 it is considered invalid Channels 800 to 990 are invalid The factory default channel setting is 333 6 Press 7 lt band order gt This key sequence is used to enter the band order The band order value is a series of digits between 1 and 2 1 and 8 for Tri Mode model that must be at least 1 digit and not more than 2 digits 8 digits for Tri Mode model long The following table describes the relationship between the band order digits and EIA TIA 136 system band assignment
30. ee i eee TELULAR Y lt gt i Fr i PHONECELL SX4e TDMA 800 MHz VoIckE FAx DATA and DIGITAL TRI MOoODE TDMA PCS AMPS VOICE FAX DATA TECHNICAL MANUAL 06 11 02 Part Number 56024002 CONTENTS i A A Phonecell SX4e Spike Antenna Power Supply Fixed Wireless Terminal FWT ce Before installing your Phonecell SX4e carefully remove the unit from the shipping carton and check for evidence of shipping damage If damage is found contact your Authorized Telular Distributor or shipping agent immediately Next make sure you have the following components e Phonecell SX4e Fixed Wireless Terminal FWT e Antenna e Power Supply and AC Line Cord SAFE OPERATION INSTRUCTIONS IMPORTANT Before installing or operating this product read the SAFETY AND GENERAL INFORMATION located at the end of this guide e Install unit indoors e Install unit on hard flat surface for proper ventilation Do not expose unit to rain or moisture Do not place unit on or close to sources of heat PLEASE SEE THE IMPORTANT NOTICES SECTION OF THIS GUIDE FOR IMPORTANT INFORMATION ON USE WARRANTY AND INDEMNIFICATION IMPORTANT NOTICES TERMS AND CONDITIONS FOR USE OF PHONECELL PRODUCTS Product These Terms and Conditions are a legal contract between you and Telular Corporation for the title to and use of the Product BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT YOU AGREE TO THE TERMS AND CONDITIO
31. ervices Contact your local cellular dealer or service provider to determine the availability of an AMPS analog network To make a fax or data modem call a special dial sequence to request an analog channel MUST be entered just before the call is made Do not use this dial sequence for a voice call If the request is successful the normal fax or data rate negotiations will commence and the call will continue The analog channel assignment lasts for the duration of the call NOTE There is no guarantee that the analog channel request will be granted there may be no analog channel available The fax or data call will fail if an analog channel is not assigned Contact your local cellular dealer or service provider to determine the availability of an analog channel The SX4e automatically adjusts the transmit and receive audio levels for optimum data transmission when a fax or modem is detected After the completion of the call the audio levels are returned to the user s previous settings patent pending The SX4e is compatible with all group 3 facsimile machines and computer modems Normally data transmission rates of up to 9600 baud are possible dependent upon the type of modem used and your cellular service provider s capability The SX4e s Status LED will indicate when an analog call has been initiated see the How to Use the LED Status Indicators section of this manual SX4e TDMA 800 e SX4e Tri Mode 10 Technical Manual Originating Fa
32. face Failure Check Wiring to Telephone C ontact your Authorized Telular Service Representative How to Place a Call 1 Pick up your telephone handset your phone is now off hook 2 Listen for dial tone If service is not available a No Service tone is produced Hang up the phone and try again If the No Service tone continues contact your service provider to make sure cellu lar service is activated 3 Dial the phone number How to Receive a Call When your telephone rings pick up the handset and begin talking How to End a Call Hang up the phone place the handset back onto the telephone cradle The Hookflash Function When you initiate the Hookflash function it automatically lets you Speed up the connection after you dial a phone number e Answer an incoming call that occurs when you re dialing a phone number e Use special supplementary cellular services which may be available in your cellular service area How to Use the Hookflash Function Depending upon your phone there are two ways to initiate the Hookflash function e Press the dedicated HOOKFLASH or FLASH key on your telephone e Press the hang up or switch hook mechanism on your phone once quickly approximately 1 2 second SX4e TDMA 800 e SX4e Tri Mode 8 Technical Manual Important Tones and Alerts No Service Tone When cellular service is not available the receiver emits a No Service fast beeping tone instead of the normal
33. ical Manual PHONECELL SX4e TROUBLESHOOTING Telephone Service is Not Working If the telephone service is not working first check the operation of the telephone equipment and wiring connected to your Phonecell Test the equipment on a different service or piece of equipment to ensure proper operation or connect a known good telephone device to the Phone port on the Phonecell unit This will verify the condition of the telephone equipment and the internal wiring of the telephone service to ensure that it s working properly If the telephone system or wiring is not work ing properly replace or repair the equipment as required Otherwise contact your cellular provider or your authorized Telular distributor Unable to Receive Incoming Calls If more than one telephone or telephone device is connected to your Phonecell make sure that all devices are on hook hung up If one extension is off hook off its cradle none of the exten sions on your phone line will ring when an incoming call occurs Unable to Send and Receive Fax or Data Calls Because most TDMA and PCS networks do not support digital fax and data services AMPS 800 MHz networks and AMPS 800 MHz channels on TDMA 800 MHz networks can be used for fax and data services There is no guarantee that the analog channel request will be granted there may be no analog channel available The fax or data call will fail if an analog channel is not assigned Contact your local cellul
34. ill remain The factory default is 0 Non Standard Control Channel Option The following key sequence is used to select the non standard control channel option Press 88 lt non standard option gt The non standard option is set to 0 to disable non standard control channels set to 1 to enable This option applies to AMPS systems only The factory default is 0 Primary A Side Non Standard Control Channel Option The following key sequence is used to select the non standard primary control channel range for A side AMPS systems Press 89 lt first ACC gt lt last ACC gt The first ACC and last ACC values must be in the range of 0 799 or 991 1023 If the value is not in the range it will be considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default for first ACC is 333 and for last ACC is 313 SX4e TDMA 800 e SX4e Tri Mode 17 Technical Manual Primary B Side Non Standard Control Channel Option The following key sequence is used to select the non standard primary control channel range for B side AMPS systems Press 90 lt first ACC gt lt last ACC gt The first ACC and last ACC values must be in the range of 0 799 or 991 1023 If the value is not in the range it will be considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default for first ACC is 334 and for last ACC is 354 Secon
35. inary telephone which is sometimes referred to as a POTS Plain Old Telephone Service phone NOTE The User Setup mode is not accessible while you re in a call In the following sections an lt entered value gt is comprised of the digits 0 through 9 The digits and are considered invalid when used inside an lt entered value gt and will cause that com mand value to be rejected If there are no key entries within any 2 minute period the FWT will revert to its normal mode Going on hook hanging up the phone will exit the setup mode Correct entry of the commands below will be confirmed by the return of the programming tone which signifies that the unit is ready to accept the next entry Incorrect entry will result in a short three tone sequence of rising frequencies followed by the return of the programming tone which again signifies that the unit is ready to accept the corrected entry How to Enter the User Setup Mode Use the following access code to enter the User Setup mode Press 0 12345678 The access code is 8 digits If the access code is not 8 digits or does not match the access code the Programming mode cannot be entered This code is pre programmed during production and cannot be changed If you enter the access code correctly the dial tone should change to a different steady Programming tone and the bottom LED indicator on the front of the Phonecell will blink alternately RED and GREEN to indicat
36. l be used to program the on hook call alert ring cadence Press 30 lt on time gt lt off time gt Both the on time and off time durations are programmed in 100 ms increments from 1 to 255 0 1 25 5 seconds If the value is not between 1 and 255 inclusive it will be considered invalid The factory default is 20 and 40 respectively On Hook Call Alert Frequency Option The following key sequence will be used to program the on hook call alert ring frequency Press 32 lt frequency gt The frequency value is set to 0 for 20 Hz 1 for 25 Hz and 2 for 50 Hz If the frequency value is greater than 2 it will be considered invalid The factory default is 0 Audio Input Impedance Option The following key sequence is used to select the audio input impedance Press 68 lt audio Z gt The audio Z value is set to 0 for 600 ohms 1 for 900 ohms If the value is neither O nor 1 it is considered invalid The factory default is 0 SX4e TDMA 800 SX4e Tri Mode 16 Technical Manual Ring Back request The following key sequence is used to request immediate ring back Press 13 There is no ring back value to be set the command activates when the phone is placed back on hook Restore Factory Defaults Request The following key sequence is used to request restoration of all factory set default values except the NAM information Press 15 There is no restore defaults value to be entered the command activates im
37. mediately If a value is entered it is considered invalid and the Phonecell will not restore the factory defaults Periodic Self Test Option The following key sequence is used to program periodic self test Press 76 lt self test interval gt The self test interval is programmed in 1 second increments from 1 to 65 535 A value of 0 disables periodic self test If the value is not between 0 and 65 535 inclusive it will be considered invalid The factory default is 180 Disconnect Pulse Option The following key sequence is used to enter the disconnect pulse option Press 79 lt disconnect pulse gt The disconnect pulse value is programmed in 1 millisecond increments from 10 to 65 535 A value of 0 disables the disconnect pulse If the value is not between 10 and 65 535 inclusive it will be considered invalid and the FWT will not update or store this value the currently stored value will remain The factory default is 700 Dial Tone Frequency Selection Option The following key sequence is used to select the dial tone frequency option Press 80 lt dial tone frequency gt The dial tone frequency value is set to 0 to select the North American dial tone frequency pair 350 440 Hz set to 1 to select European dial tone frequency 425 Hz If the dial tone fre quency selection option value is neither 0 nor 1 it is considered invalid and the FWT will not update or store this value the currently stored value w
38. n either direction Up or Down The volume setting remains in effect for future calls until changed manually even if the telephone is on hook If the SX4e power is cycled turned OFF ON the default mid range volume setting will be restored Variable Dial Time Auto SEND Delay Option When you place a call your Phonecell SX4e automatically sends the phone number over the cellu lar network after you dial the last digit However to make sure you have enough time to dial the last digit a 3 second Auto SEND Delay is programmed into the unit at the factory To change the Auto SEND Delay setting see the User Programming Commands section of this manual In Call DTMF Signaling Option Depending upon your cellular provider the Data After SEND option may need to be Enabled or Disabled to use special cellular features such as call waiting three way conference calls voice mail etc Please consult your service provider for the required In Call DTMF Signaling configura tion The factory default setting is 0 In Band Signaling only To change the Data After Send setting see the How To Set the Auto SEND Delay in the Phonecell SX4e Programming section of this manual SUPPLEMENTARY SERVICES NETWORK DEPENDENT Call Waiting Call Waiting enables you to be alerted to an incoming call while you are already on a call You have the option of responding to the second call while putting the first call on hold You can also disable the call waiting option
39. omer only if the customer is a Buyer direct ly from Telular that the Products including accessories shall comply with the applicable Specifications and shall be free from defects in material and workmanship under normal use and service for a period of fifteen 15 months from date of ship ment from Telular Telular at its option shall at no charge either repair replace or refund the purchase price of the Product during the warranty period provided itis returned by Buyer in accordance with the terms of this warranty to the Telular des ignated repair center Repair or replacement at Telular s option may include the replacement of parts boards or Products with functionally equivalent reconditioned items Repaired and replacement items are warranted for the balance of the orig inal warranty period All replaced items shall become the property of Telular SUCH ACTION ON THE PART OF TELULAR SHALL BE THE FULL EXTENT OF TELULAR S LIABILITY HEREUNDER AND BUYERS EXCLUSIVE REMEDY Buyer shall be responsible for all costs and expenses incurred by Buyer including without limitation any handling labor or trans portation charges OTHER THAN AFORESAID THIS EXPRESS WARRANTY IS EXTENDED BY TELULAR TO BUYER ONLY AND NOT TO BUYER S CUSTOMERS OR USERS OF BUYER S PRODUCTS Il HOW TO OBTAIN WARRANTY SERVICE Product covered under this warranty shall only be accepted from and returned to Buyer s designated repair center Buyer s dealers distributors agents and en
40. on 3 To add more telephones plug in a line splitter not supplied to the phone port see Figure 8 NOTE The SX4e will only let you make one phone call at a time a ae z poe R Line eiA PAFI Torts GSE spie E k ir pnp P Phone 5 To Phone Port H H Cords Figure 8 An optional Line Splitter lets you connect additional phones to your Phonecell SX4e Figure 7 Connect the SX4e to a telephone SX4e TDMA 800 e SX4e Tri Mode 6 Technical Manual HOW TO SET UP YOUR PHONE NUMBER Your SX4e has been designed for easy setup and installation You can program the Phonecell SX4e with an ordinary tone dial DTMF telephone which is sometimes referred to as a POTS Plain Old Telephone Service phone Note This programming mode is not accessible while you re in a call Before you begin programming connect the antenna plug in the power and connect a tone dial DTMF telephone 1 Pick up the POTS telephone handset and listen for a tone either a steady dial tone or a beeping no service tone 2 Press 0 12344321 The tone will change to a different steady Programming tone and the bottom LED indicator on the Phonecell will blink alternately RED and GREEN to indicate that you re in programming mode You now have two minutes to start the programming steps 3 Press 1 lt MIN gt This key sequence is used to enter your 10 digit telephone number Mobile Identification Number or MIN If you enter the number incorr
41. ve analog channels available the call will be unsuccessful Try the call at a later time NOTE As a result of using this dial string prefix the SX4e will be placed in the analog mode and an analog channel will be requested before the call is dialed If the request is successful the data rate negotiations will commence and the call will continue The FWT Status LED will indicate an analog call by flashing green Receiving Fax and Data Calls When your fax machine or modem answers a call the Phonecell will decode the answer tone from the local device This will cause the Phonecell to go to analog mode regardless of which mode is currently set to receive the data or fax The FWT Status LED will indicate an analog call by flash ing green You do not need to do anything to allow your unit to receive fax or data calls However the facsimile machine and or computer data modem must be connected to the Phonecell SX See Step by Step Fax Instructions If the call is not completed successfully the remote caller should retry the call immediately The Phonecell SX4e will remain in analog mode for a short time after call failure waiting for retry Refresh FWT to Digital Mode When the analog fax data call ends the FWT Status LED will return to continuous green indicating the FWT has returned to its normal operating digital mode SX4e TDMA 800 e SX4e Tri Mode 11 Technical Manual PHONECELL SX4e USER SETUP The SX4e can be programmed with an ord
42. x and Data Calls Sending a Fax Message 1 Set up your fax machine just as you a would for a wired telephone line C f 2 If your fax machine has a prefix Lo I igi W setting set it to 2 If your pro ee y gram does not have such a setting f Telephone Cord x 7 add 2 to the phone number as eee shown in the example below T Phone Port Example If you are sending to Fax Machine 1 800 123 4567 enter 218001234567 The 2 tells the SX4e to use the analog mode for this call only 3 Your fax should then proceed normally NOTE If the network does not have analog channels available the call will be unsuccessful Try the call at a later time Sending Data a i api 1 Connect your computer modem to I EA pt y p la E ip Figure 11 Connecting a fax machine to the SX4e the Phonecell SX4e exactly the same way you would to wired tele phone service e i Telephone Cord 2 If your modem communications l ee Bx program has a prefix setting set it Sas ay Computer Phone Port to 2 If your fax machine does not have such a setting add 2 Figure 12 Connecting a computer to the SX4e to the phone number as shown in the example below Example lf you are sending to 1 800 123 4567 enter 218001234567 The 2 tells the Phonecell to use the analog mode for this call only 3 Your data transmission should then proceed normally NOTE If the network does not ha
Download Pdf Manuals
Related Search