Teka Vr.03 User's Manual
Contents
1. a steady air flow has been established before Lu fumes appear Allow the extractor fan to run for several minutes after you have finished cooking between 3 to 5 minutes in order to expel all the grease from the outlet duct This prevents the return of grease smoke and smells 11 ENG Cleaning and maintenance During cleaning and maintenance work make sure the safety instructions set out on page 10 are complied with Cleaning the hood body f your kitchen hood is made from stainless steel use proprietary cleaners mentioned in the product instructions Never use metallic scourers nor abrasive or corrosive products Dry the kitchen hood using a cloth that does not produce fibres Cleaning the metal filters To remove the filters from their fittings press lightly on the locks and then pull them off The metal filters can be cleaned by soaking them in hot water with neutral detergent until the fat dissolves and then rinsing them under the tap or using special anti grease products They can also be washed in a dishwasher In this case it is advisable to stack them vertically to avoid food residues to stick to them Cleaning in a dishwasher may damage the metallic surface blackening it although this will not affect its fat retention capacity Once clean leave them to dry off and then fit them onto the kitchen hood Changing light bulbs Proceed as follows Unscrew the lamp cap trimming cover2. Change the broken burnt out lamp Maximum lamp power is 20 W G 4 Screw in the lamp cap trimming cover Problem solving Proceed with the following checks before calling the Technical Service The extractor fan does not work network There is no current in the network The kitchen hood does not extract sufficiently or vibrates Obstruction in the air exit conduct The lamps do not light up The lamps are blown The lamps are slack The mains cable is not connected to the Filters are saturated with fat Connect mains cable to the network Provide current to the network Change or clean the active charcoal and or metal filters as the case may be Remove the obstruction Change the lamps Tighten the lamps Sizes and specifications See page 30 TEKA INDUSTRIAL S A reserves the right to make changes and corrections to its products as it deems necessary without altering their basic characteristics 12 Accesories supplied 150 120 mm reduction Screws O4 x 12 Screws O4 x 10 Lock screws M8 x 45 DA HRA Installation Fig 1 Page 31 On installing the kitchen hood make sure that the Safety Instructions set out on page 10 are complied with To obtain optimum performance the external conduct must not be more than FOUR METRES long have no more than two 90 angles and its diameter must be at least 120 1 Using the support O trace and drill the where the screw fittin
3. 2 273 19 45 2 273 10 88 China Shanghai TEKA CHINA LTD 86 21 6236 2375 21 6236 2379 Czech Republic Brno TEKA CZ S R O 42 05 4921 0478 05 4921 0479 France Saint Ouen l Aum ne TEKA FRANCE SAS 33 0820072747 0134301596 Greece Athens TEKA HELLAS A E 30 210 9760283 210 9712725 Hungary Budapest TEKA HUNGARY KFT 36 1 354 21 10 1 354 21 15 Indonesia Jakarta P T TEKA BUANA 62 21 39052 74 21 39052 79 Malaysia Kuala Lumpur TEKA K CHENTECHNIK MALAYSIA SDN BHD 60 3 762 001 600 3 762 01 626 Mexico Mexico D F TEKA MEXICANA S A DE C V 52 555 762 04 90 555 762 05 17 Poland Pruszk w TEKA POLSKA SP ZO O 48 22 738 32 80 22 7308 32 89 Portugal IIhavo TEKA PORTUGUESA LTDA 351 234 32 95 00 234 32 54 57 Russia Moscow TEKA RUS LLC 7 095 737 4689 095 737 4690 Singapore Singapore TEKA SINGAPORE PTE LTD 65 6 73 42415 6 73 46881 Thailand Bangkok TEKA THAILAND CO LTD 66 2 5164954 2 9021484 The Netherlands Zoetermeer TEKA B V 31 79 345 15 89 79 345 15 84 Turkey Istanbul TEKA TEKNIK MUTFAK A S 90 212 274 61 04 212 274 56 86 U K Abingdon TEKA PRODUCTS UK LTD 44 1235 86 19 16 1235 83 51 07 U S A Tampa TEKA USA INC 1 800 419 9344 813 228 8604 Venezuela Caracas TEKA ANDINA S A 58 212 291 28 21 212 291 28 25 Mod 4 748 Gr ficas Alhambra Teka Industrial S A Cajo 17 39011 Santander Spain Tel 34 942 35 50 50 Fax 34 942 34 76 94 http www teka net CKO KUCHENTECHNIK Teka Kuchentechn
4. A13 3 Connect the upper part of the inner tube not supplied to the circular support exit A13 4 Using the support O trace and drill the where the screw fittings will sit onto the roof S Q8 x 45 5 Screw the support O into the roof with the screw fittings S 28 x 45 6 Mount the upper chassis A6 onto the support O using the screws Q M6 x 16 7 Mount the upper cover A8 and attach it to the upper chassis A6 with the screws G M4 x 12 8 Fit the part B if the inner tube not supplied is 0120 9 Mount the whole lower unit to the upper section attaching it to the roof using the screws A10 M4 x 12 at the required height 10 Attach the inner tube with a clamp not supplied to B or on to the motor s air outlet vent as the case may be 11 Mount the lower part A9a of the cover to the lower chassis A7 with the screws I M4x12 12 Adjust the lower part A9b of the cover A9a as shown in the diagrams 13 Remove the metal filters Loosen the screws without unscrewing them of the EASYCLEAN panels A19 move the panels aside carefully and take them off 14 Put the filters into the lateral draught section of the motor making the holes in the filters match up A11 with the pivots A12 of the motor carcass 15 Mount the EASYCLEAN panel again A19 Fit the metal filters 13 e lu 30 CAMPANA DECORATIVA C digo T cnico TEKA INDUSTRIAL SA o aa No SANTA
5. of fumes produced during food preparation It will be your responsibility if it is used for other purposes which may be dangerous The manufacturer cannot accept responsibility for damage caused by improper use of the appliance For repairs please contact the nearest TEKA Technical Assistance Service and always use genuine spare parts Repairs or modifications carried out by unqualified personnel can cause malfunctions or may damage the appliance putting your safety in danger This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE This guideline is the frame of a European wide validity of return and recycling on Waste Electrical and Electronic Equipment X Index Page Description of the appliance 11 Instructions for use 11 Cleaning and maintenance 12 Problem solving 12 Sizes and specifications 12 Accessories supplied 13 Installation 13 Active charcoal filters 13 Description of the appliance A On Off Push button speed selector light and working pilot Metal filters Lamps 20 W G 4 D E Vertically adjustable tubecovers O Instructions for use You may control the kitchen hood by operating the controls as shown in the diagram Minimum speed Medium speed Maximum speed Extra fan Pilot indicator Switch on the extractor fan a few minutes before you start to cook in order to ensure that
6. Manual de Instrucciones Campanas Extractoras DS ISLA Vr 03 Bedienungsanleitung Dunstabzugshauben DS ISLA Vr 03 Instructions Manual Kitchen Hoods DS ISLA Vr 03 Manuel d instructions Hottes aspirantes DS ISLA Vr 03 Manual de Instruc es Exaustores DS ISLA Vr 03 OAHITEZ XPHXEOX KAMINAAA TOIXOYDS ISLA Vr 03 Kullanim Kilavuzu Davlumbaz DS ISLA Vr 03 CKA K CHENTECHNIK ENG Dear client Congratulations on your choice We are sure that this modern functional and practical appliance made with top quality materials will fully satisfy your needs Please read every section of this INSTRUCTIONS MANUAL before using your kitchen hood for the first time to ensure maximum performance from the appliance and to avoid breakdowns which may be caused by incorrect use as well as to allow any minor problems to be solved Store this manual as it will provide useful information about your kitchen hood at all times and will also help other people to use it Safety Instructions Please be aware of current local regulations with reference to domestic electrical fittings and gas eduction Verify that the tension and frequency of the network match those indicated on the label located inside the kitchen hood The appliance must be connected to the network using a break switch with a universal cut off and minimum contact separation of 3 mm THE NET CABLE MUST NOT BE SUBTITUTED Once the kitchen hood ha
7. NDER E No KATAEKET HE NENNLEISTUNG HALOGENLAMPEN POTENCIA NOMINAL DAS LAMPADAS ETH XII 8 Lt 9 F EIEISCHIEIEN zd TE x 3 Potencia W de eee 20 20 50 2 x 20 250 880 m h E LEA 2x20 270 780 m h Ver Placa de Caracter sticas en el interior de la campana CODE NR NETZSPANNUNG V puit ie a LEISTUNG 220 230 2 x 20 250 880 m h Siehe Typenschild im Innern der uL 20 230 850 2x20 250 880 m h t 110 120 ss 2x20 270 780 mi h Check Characteristics label inside the hood gt 220 230 50 2x 20 250 880 m h Voir Plaque des Caract ristiques l int rieur de la hotte C digo T cnico Tens o V Da Rede Frequ ncia Hz Da Rede riim or Caudal De Aspirag o 220 230 50 2 x 20 250 880 m h V r Placa de caracter sticas no interior do exhaustor oo 50 2x20 250 880 m h Ex y te mv Taur la Teyvik v Xapaktrnptotik v H GOA otov axoppogntpa Teknik Kodu Hat Gerilimi V Hat Frekansi Hz Isik Motor G c W T 220 280 2x 20 250 880 mh Cihazin zerindeki teknik zellikler etiketini kontrol ediniz TEKA GROUP COUNTRY CITY COMPANY CC PHONE FAX Austria Wien K PPERSBUSCH GES M B H 43 1 86680 0 1 86680 72 Belgium Zellik B V B A K PPERSBUSCH S P R L 32 2466 8740 2466 7687 Chile Santiago de Chile TEKA CHILE S A 56
8. gs will sit onto the roof S Q8 x 45 2 Screw the support O into the roof with the screw fittings S 28 x 45 3 Mount the upper chassis A6 onto the support O using the screws Q M6 x 16 4 Connect the upper part of the inner tube not supplied to the exit 5 Mount the upper cover A8 and attach it to the upper chassis A6 with the screws G M4 x 12 6 Fit the part B if the inner tube not supplied is 0120 7 Mount the whole lower unit to the upper section attaching it to the roof using the screws A10 M4 x 12 at the required height 8 Attach the inner tube with a clamp not supplied to B or on to the motor s air outlet vent as the case may be 9 Mount the lower part A9a of the cover to the lower chassis A7 with the screws I M4 x 12 10 Adjust the lower part A9b of the cover A9a as shown in the diagrams Active charcoal filters Optional When exterior gas extraction is not possible then the kitchen hood may be set to purify the air by recycling it through active charcoal filters The active charcoal filters have an active life of between three to six months depending on the individual conditions of use These filters cannot be washed nor regenerated They must be replaced once their useful life comes to an end Fig 1 Page 31 1 Mount the diffuser support A13 onto the upper chassis A6 with the screws A4 M4 x 12 2 Adjust the diffuser A5 over the support
9. ik GmbH Sechsheldener Str 122 35708 Haiger Germany Tel 49 2771 8141 0 Fax 49 2771 8141 10 http www teka net JKP 06 03
10. s been installed ensure that the mains cable to the network is not in contact with any live metal edges Avoid connecting the appliance to conductors used as exits for fumes produced by a non electric energy source e g boilers chimneys etc f the extractor fan is going to be used simultaneously with equipment powered by a non electric energy source e g gas cookers then the room must have sufficient ventilation Excessive fat accumulation in the kitchen hood and metal filters is a fire risk and may 10 also cause dripping therefore the inside of the kitchen hood and the metal filters must be cleaned at least once a month The lower part of the kitchen hood must be fitted at least 50 cm over electric hobs and 65 cm over gas or mixed hobs FOLLOW THE HOBS MANUFACTURER S MINIMUM RECOMMENDATIONS Never leave gas hobs lit if not covered by a container The fat accumulated in the filters may drip or catch fire when the temperature increases Avoid cooking under the kitchen hood if the metal filters are not fitted e g while they are being cleaned in the dishwasher You must not produce flames under the kitchen hood Disconnect the appliance before any interior manipulation e g during cleaning or maintenance We recommend the use of gloves and to be extremely careful when cleaning the kitchen hood s interior Your kitchen hood is designed for domestic use and only for extraction and purification
Download Pdf Manuals
Related Search