Taylor Today's weather 24 hour forecaster 1383 User's Manual
Contents
1. 2 The base unit is intended for indoor use only It is not sealed against moisture and could be damaged if used outdoors 3 Do not immerse the base unit in water If you spill liquid on it dry immediately with a soft lint free cloth 4 The remote sensor is weather resistant but not waterproof and should never be submerged in water It should be placed away from direct sunlight rain and snow 5 Do not clean the units with abrasive or corrosive materials This may scratch plastic parts and corrode electronic circuits 6 Do not subject units to excessive force shock dust temperature or humidity This may result in malfunction shorter electronic life span damaged battery or distorted parts 7 Do not tamper with the units internal components Doing so will invalidate the warranty on this product and may cause damage The units contain no user serviceable parts 8 Do not mix old and new batteries Do not mix Alkaline Lithium carbon zinc standard or NickelLCadmium rechargeable bat teries Do not dispose of batteries in fire Batteries may explode or leak Remove the batteries if the units will not be used for a long period of time 9 Due to continuous product improvements the illustrations shown in this manual may differ from the actual displays 10 If you choose to place the remote sensor indoors in a basement attic child s room etc the sensor will not be tracking outdoor conditions and the base unit will2. re mote are within a 200 foot range Check that there are no major obstacles between the units that may block signals such as build ings trees etc Try to have no more than 2 or 3 walls between the units Try various locations and shorten the distance between units if necessary Over or under temperature range displays If the temperature is outside the unit s temperature range of 4 F to 158 F 20 C to 70 C with use of lithium batteries the LCD will show HH higher than the temperaturerange or LL lower than the temperature range When temperatures are within the range the readings will return If necessary relocate the remote sensor away from loca tions with extreme temperatures such as snow or a hot surface 10 Transmission Information The remote sensor sends temperature and weather condition information to the base unit After installing batteries into both units allow 6 hours to analyze weather conditions and report forecasts Weather readings will update as follows e Current temperature updates approximately every 1 minute e Temperature and weather forecasts update every 6 hours during the first 24 hours of operation after battery installation e After 24 hours updates occur every 1 hour If there are no changes on the display after 6 hours press the SYNC button to send a new signal to repeat the transmission cycle After an extreme temperature change ex relocating the sensor f
3. ME DATE 4 Press UP or DOWN to switch between a 12 or 24 hour clock Press TIME DATE Press UP or DOWN to change the year Press TIME DATE Press UP or DOWN to change the month Press TIME DATE Press UP or DOWN to change the date Press TIME DATE Weather Forecaster and Clock Date setup are complete Press TIME DATE to toggle between the time and year displays SYNC CF CON AD Reading the Weather Forecaster Current outdoor temperature at remote sensor location Current outdoor humidity at remote sensor location Current weather condition icon Current indoor temperature lock Date Base unit low battery indicator Transmission signal icon Remote sensor low battery indicator B 5 forecast displays over 24 hours A Weather condition forecast icon B Outdoor temperature forecast C Outdoor humidity forecast N Q OONAOARW Afternoon 2PM 6PM Evening Overnight Morning Forecast screens will rotate as time periods change with the next period appearing at the left Additional Features C F Selection Press the C F button on the back of the base unit to switch between Fahrenheit and Celsius temperatures Backlight Press the Backlight button on the top of the base unit The LCD screen will light up for approximately 5 seconds Low Battery Warning Base unit r
4. TAYLOR E Today s Weather 24 Hour Forecaster Instruction Manual Get actual current temperatures and predict the weather conditions for the next 24 hours as well as your local television weatherperson Taylor uses the temperature and changes in relative humidity levels to forecast the upcoming day Plan the day with confidence with Taylor Today s Weather Please read this instruction manual carefully before use and keep these instructions handy E To Power and Set Up the Weather Forecaster S 154 801 6 7 55 55 98 98 58 Battery Power 2 AAA alkaline for base unit not included 2 AAA lithium for remote sensor recommended not included Remove the battery compartment cover on the back of the base unit Install 2 AAA batteries according to the polarity markings in the compartment and replace the cover Important Install the base unit batteries first before installing the remote sensor batteries for proper signal connection A Set Current Weather Conditions 1 After battery installation the current weather icon flashes ad a Ent N a k L om eal 2 Press Up or Down to select the weather icon you believe most closely reflects the current conditions in your area Partly Cloudy is the default setting Weather Icons Partl Sunny Cloudy Cloudy Rain Snow ahy a bililillidit e aeg 3 Press Time Date to select the displa
5. atteries Lithium batteries are recommended for the remote sensor since alkaline batteries may freeze or otherwise become damaged in extreme temperatures The sensor will function with alkaline batteries but are best suited for milder climates See Specifications EJ Problem Solving 1 If the LCD readout is faint replace the batteries 2 If outdoor temperature does not display on the base unit a Press the SYNC button to trigger a signal from the base to the remote b Relocate remote sensor if it is obstructed from weather condi ions or in contact with an object that might affect tempera ure readings hot metal object snow etc c Remove and reinstall all batteries using new fully charged batteries d Repeat set up procedures e Place the remote sensor closer to the base unit e Position the base and remote within range and without interfer ing obstructions between units 3 If new batteries are faulty on the initial installation install fresh batteries If you did not notice the Low Battery icon warning and the product performed correctly after initial set up the batteries have lost their charge Replace the batteries see To Power and Set Up the Weather Forecaster General Information Display Information If the base unit does not receive a transmission from a remote channel for 1 hour the display will show dashes Press the SYNC button to send a signal manually Check that the base and
6. eh Mh A hdd 72 72 72 22 22 Only the current temperature will update during first 6 hours Temperature forecasts and weather icons stay identical while analyzing 1st forecast 5 After the first 6 hours when the units begin to forecast weather conditions all temperature and weather screens will update with new forecasts Current humon S lt OT rir CO 45 12 08 amp 8 GO Metts ic vil OUT ka Hilbtdiad Today maaay Todsy anamoon S cas 74 GSD S KD _ 15 80 679 55 65 50 84 90 99 58 2 Temperature and Weather forecasts update 6 The remote sensor will automatically transmit weather condi tions to the base unit e Indoor temperature readings will update approximately every 30 seconds e Current outdoor temperature readings will update approximately every 1 minute Outdoor temperature outdoor humidity and weather condition forecasts will update every 6 hours during the first 24 hours of operation After the first 24 hours updates occur every 1 hour Please note if the remote senses identical weather conditions over a 24 hour period the screens will all show identical readings To Set Clock and Date ee and hold TIME DATE for 2 O O O TIME DATE UP DOWN seconds then release O O 2 Press UP or DOWN to change the hours Press TIME DATE 3 Press UP or DOWN to change the minutes Press TI
7. eplace both batteries when the icon appears on the right side of the screen Current TEMP HUMIDITY oo WN Wh bibl Ww T T IN VAN Remote sensor replace both batteries when the E icon appears on the left side of the screen ElTips Setup Place the base unit as close as possible to the remote sensor during setup This will ensure the best reception of signals as you set up your wireless forecaster OUT Location Position the base unit and remote sensor within the effective trans mission range of 200 feet 60 meters Place the base unit indoors in a well ventilated location away from direct sunlight Place the remote sensor in a dry shaded area Direct sunlight will heat the casing and inflate temperatures readings EXTips continued Important Though the remote unit is weather resistant it should be placed away from direct sunlight rain snow and should never be sub merged in water Note The effective range is greatly affected by the building materials and where the base and remote units are positioned Try various set ups for the best results Check to make sure the transmission path is clear of obstacles and interference Shorten the distance between base and remote units when necessary Placement Table stand use to sit the units on a flat surface such as a desk or countertop Keyhole use to hang on a wall Keyhole Table stand Back View B
8. not be able to receive an ac curate weather forecast IB Specifications Range of temperature measurement Base unit indoor only 14 F to 122 F 10 C to 50 C Remote sensor With Lithium batteries 4 F to 158 F 20 C to 70 C With Alkaline batteries 14 F to 122 F 10 C to 50 C Resolution 1 for temperature Outdoor Humidity 20 99 RH Power Base unit 2 AAA alkaline batteries Remote sensor 2 AAA lithium batteries recommended for wider temperature range 5 weather forecast icons Sunny Partly Cloudy Cloudy Rain Snow 5 forecast time displays over 24 hours Evening 6PM 10PM Overnight 10PM 6PM Morning 6AM 10AM Midday 10AM 2PM Afternoon 2PM 6PM 12 24 clock with date and year 5 second backlight Transmission Max 200 ft 60m open area RF433 92MHz One Year Limited Warranty This product is warranted against defects in materials or workmanship for one 1 year from date of original purchase for original purchaser It does not cover damages or wear resulting from accident misuse abuse commercial use or unauthorized adjustment and or repair Should this product require service or replacement at our option while under warranty do not return to retailer Please pack the item carefully and return it prepaid along with store receipt showing date of purchase and a note explaining reason for return to Taylor Precision Products 2220 Entrada Del Sol Suite A Las Cruces New Mexico 88001 www ta
9. rom a warm indoor location to snowy outdoors allow a few minutes for the temperature reading to stabilize Transmission Collision Signals from other household devices such as doorbells home security systems and entry controls may interfere This is normal and does not affect the general performance of this product The transmission will resume once the interference recedes Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Modifications not authorized by the manufacturer may void user s authority to operate this device H Precautions 1 Always read the instruction manual before operating this product
10. s are recommended for the wider temperature range EJ Set Up Remote Sensor 1 After installing the batteries into the base unit and the remote sensor place the units close together for best setup connection 2 Press the SYNC button on the back of the base unit to send a transmission signal to the remote sensor Allow a few minutes for a connection as the F icon flashes and the temperature digits show dashes When connected the icon disappears Current HUMIDITY _ 1 0 AM E QD age IEU y IZ i A Sey NMA Zane dilililidlitl IN F icon flashes while transmitting disappears after connection to remote 3 After a signal is received position the remote sensor at an outdoor location within 200 feet of the base unit in a dry shaded area Direct sunlight will heat the casing and inflate temperatures readings Important Though the remote is weather resistant it should be placed away from direct sunlight rain snow and should never be submerged in water 4 Allow at least 6 hours for the remote to analyze weather conditions and report forecast readings During that time indoor temperature will update every 30 seconds and appears on the forecast screens Outdoor temperature and humidity show and all weather icons are identical Current gt sve MUMMY yan m f BO q5 12 00 eg et I vod out Rhin ili IN EID ED KD D K WEL AMA MD bh AA MAY Udit dad beh d ddd Wh bth Ub hb Vib ddd b d
11. yed weather icon The icon stops flashing Current TEMP HUMIDITY a ee E rc CD 476 00 She ee MA im ved out Nhat Mal IN Icon flashes during setup then steady when set 4 The selected weather icon appears on all screens The temperature and forecast readings update after remote sensor is added f Current N Teve HUMIDITY pon am GOD qy 1200 aa ny Mhhltd IT yi out Uhhh N Today Midday Today Afternoon Today Evening Today Overnight Moming Tomorrow CCOA TD TS KT TAA ALA Mh bib Al ML dD Adal A AAA AM hh bad VAAA ALA bb A AAG AAA bide d he ddd dd hed ad SSF Rl SOF ware Flr Ak S B Install Batteries into Remote Sensor Important Install the remote sensor batteries after installing the base unit batteries for proper signal connection Remote sensor use 2 AAA lithium batteries not included Remove the screws from the battery compartment on the back of the remote take care not to misplace the screws Install the batteries according to the polarity markings in the compartment Replace the cover and the screws Please note The TX button does not operate any functions on this unit please disregard Battery Advice Alkaline batteries will read outdoor temperatures from 14 F to 122 F 10 C to 50 C Lithium batteries will read outdoor temperatures from 4 F to 158 F 20 C to 70 C Although alkaline batteries may be used lithium batterie
12. ylorusa com 1 866 843 3905 There are no express warranties except as listed above This warranty gives you specific legal rights and you may have other rights which vary from state to state For additional product information or warranty information in Canada or elsewhere outside the USA please contact us through www taylorusa com Made to our exact specifications in China 2011 Taylor Precision Products and its affiliated companies all rights reserved
Download Pdf Manuals
Related Search