Tanaka TCP-381 User's Manual
Contents
1. 3 3 The spark plug condition is influenced by e An incorrect carburetor setting e Wrong fuel mixture too much oil in the gasoline e A dirty air filter e Hard running conditions such as cold weather These factors cause deposits on the spark plug electrodes which may result in malfunction and starting difficulties If the engine is low on power difficult to start or runs poorly at idling speed always check the spark plug first If the spark plug is dirty clean it and check the electrode gap Readjust if necessary The correct gap is 0 6 mm The spark plug should be replaced after about 100 operation hours or earlier if the electrodes are badly eroded NOTE In some areas local law requires using a resistor spark plug to suppress ignition signals If this machine was originally equipped with resistor spark plug use same type of spark plug for replacement Muffler Fig 3 4 Remove the muffler and clean out any excess carbon from the exhaust port or muffler inlet from time to time in order to avoid power loss www tanakapowerequipment com 6 custsvc tanaka ism com lanaka _ tezsmoss Ss wner s Manual Maintenance schedule Below you will find some general maintenance instructions For further information please contact your service dealer Daily maintenance e Clean the exterior of the pump e Check that nuts and screws are sufficiently tightened Weekly maintenance e Check the starter especially cord and re2. zsmoss Ss wner s Manual Priming Fig 2 2 It is necessary to prime the pump before the initial usage This is done by filling the pump body with water via the priming plug on the top of the pump housing CAUTION Never start the machine without priming water in the pump It will cause serious damages to the engine and pump parts the manufacturer cannot quarantee in this case Fig 2 3B Starting Fig 2 3 3 B Open the Fuel cock 3 TCP 381 Fig 2 3B 1 Set choke lever to CLOSED position 1 2 Set the throttle lever to approximately 1 2 throttle opening 2 3 Pull recoil starter briskly taking care to keep the handle in your grasp and not allowing it to snap back Fig 2 4 4 When you hear the engine wants to start return choke lever to RUN position open Then pull recoil starter briskly again 5 After starting the engine allow it to warm up for 2 3 minutes before subjecting it to any load Fig 2 6B Fig 2 5 Running If water does not come out smoothly while using stop the engine and wash the suction strainer Fig 2 5 CAUTION Do not pump oil etc which is flammable NOTE After the pumping of seawater chemical fluid or urine wash the pump with fresh water Stopping Fig 2 6 6B When the engine is to be stopped gradually decrease the engine speed to an idle and then stop the engine The engine is stopped by completely raising the throttle lever www tanakapowerequipment
3. Tanak Owner s Manual Model Numbers TCP 25 TCP 210 Date 05 12 01 TCP 381 PUMPS P N 25121 TCP 210 Supplier To The Outdoor Power Equipment Industry ISM Inc 1028 4 Street SW Auburn WA 98001 Phone 253 333 1200 Fax 253 333 1212 www tanakapowerequipment com custsvc tanaka ism com lanaka _ tesz owner s Manual Before using this unit Read the operator s manual carefully Check that the cutting equipment is correctly assembled and adjusted Start the unit and check the carburetor adjustment See Maintenance WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects and other reproductive harm Al headand teg Read understand and follow all warnings and ways Wear ce ede ibe Sar prorecrors instructions in this manual and on the unit when using this unit h ae 141 LH i ER __ Explains choke position Upper sign indicates It is important that you read fully understand choke closed and the lower fully open and observe the following safety precautions and warnings Careless or improper use of the unit may cause serious or fatal injury www tanakapowerequipment com 1 custsvc tanaka ism com Tanaka to 2siztoss1 Owner s Manual 1 What is What Since this manual covers several models there may be some difference between pi
4. com 5 custsvc tanaka ism com Tanaka Fig 3 2 s AG eB TCP 25 L Y G 2 TCP 381 ke Fig 3 4 TCP 25 210 381 Owner s Manual 5 Maintenance Water pump Fig 3 1 All water in the pump should be drained from the housing by means of the drain plug Water left in the pump housing may cause damage by corrosion there is also the danger of freeze up damage in cold weather NOTE When the pump is used for the pumping of seawater chemical fluid or water which may contain any type of contaminant the pump should always be run through with clean water prior to storage Air filter Fig 3 2 The air filter must be cleaned from dust and dirt in order to avoid e Carburetor malfunctions e Starting problems e Engine power reduction e Unnecessary wear on the engine parts e Abnormal fuel consumption Clean the air filter daily or more often if working in exceptionally dusty areas Cleaning the air filter Remove the air filter cover and the filter Rinse it in warm soap suds Check that the filter is dry before reassembly An air filter that has been used for some time cannot be cleaned completely Therefore it must regularly be replaced by a new one A damaged filter must always be replaced NOTE TCP 25 Saturate the element in 2 cycle oil or the equivalent Squeeze the element to distribute the oil completely and to remove any excess oil Spark plug Fig
5. ctures and your unit Use the instructions that apply to your unit Carrying Handle Delivery Port Priming Plug Suction Port Drain Plug Throttle Lever Base Choke Lever Recoil Starter 10 Air Cleaner 11 Fuel Tank 12 Fuel Cock CONDO AWNE TCP 381 www tanakapowerequipment com 2 custsvc tanaka ism com Tanaka tezsmoss wner s Manual 2 Warnings and Safety Instructions Before operation e Protection is required for head eyes ears hands and feet Wear a suitable hard hat goggles ear covers heavy gloves and safety shoes e Dress properly do not wear loose clothing or jewelry that could become caught in moving parts of the unit e Never let a child or inexperienced person operate the machine e Be sure to check bolts and other fasteners to see if any of them have become loose or are missing On fuel e Never operate the engine with gasoline only e This engine uses a fuel mix of 25 50 parts regular gasoline to 1 part of two stroke oil The fuel should be premixed prior to pouring into the fuel tank It is recommended a quality two stroke oil be used in the fuel mix e Failure to mix oil with gasoline will result in seizure and severe damage to the engine e Do not use gasoline containing alcohol or gasohol e Do not smoke when the fuel is supplied and when you are working with the machine e Do not touch tank cap or fill the fuel tank while the engine is running or still warm The fuel should be poure
6. d into the fuel tank when the engine is cold e Never start the machine without priming water in the pump It will cause serious damages to the engine and the pump the manufacturer cannot guarantee in this case e Care must be taken to ensure that an air tight connection is made between the female unions and the male pump stubs An air leak at either union will greatly reduce the pump efficiency or no water is pumped at all e A strainer should always be used on the suction hose to prevent debris from entering the pump body and causing possible damage to the impeller During operation e The unit should be operated in well ventilated area e Never carry the unit with the engine running e For safety the unit should not be started without priming water e Do not pump oil etc which is flammable e After the pumping of seawater chemical fluid or urine wash the pump with fresh water CSWaRNING Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed CAUTION Indicates a possibility of personal injury or equipment damage if instructions are not followed NOTE Helpful information for correct function and use www tanakapowerequipment com 3 custsvc tanaka ism com Tanaka TCP 25 210 381 3 Assembly Procedure Hose to pump connection Fig 1 1 Care must be taken to ensure that tight connection is made between the female unions and the male pump stubs NOTE An air leak at
7. either union will greatly reduce the pump efficiency or no water is pumped at all Strainer Fig 1 2 CAUTION A strainer should always be used on the suction hose to prevent debris from entering the pump body and causing possible damage to the impeller 4 Operating Procedures Fuel e Always use branded 89 octane unleaded gasoline e Use Tanaka two cycle oil or a quality two cycle oil at mixing ratio of 25 50 1 Gasoline A Oil B only for the state of California at 50 1 e Never use multi grade oil 10 W 30 or waste oil e Always mix fuel and oil in a separate clean container e Always start by filling half the amount of fuel which is to be used Then add the whole amount of oil Mix shake the fuel mixture Add the remaining amount of fuel e Mix shake the fuel mix thoroughly before filling the fuel tank Fueling AS WARNING e Always shut off the engine before refueling Owner s Manual Fig 1 2 e Slowly open the fuel tank when filling up with fuel so that possible over pressure disappears e Tighten the fuel cap carefully after fueling e Always move the unit at least 3 m 10 ft from the fueling area before starting Before fueling clean the tank cap area carefully to ensure that no dirt falls into the tank Make sure that the fuel is well mixed by shaking the container before fueling www tanakapowerequipment com 4 custsvc tanaka ism com lanaka _ te
8. tions with the following time distribution Y idle 1 2 full speed x All data subject to change without notice www tanakapowerequipment com 8 custsvc tanaka ism com lanaka _ te rsiztose1 Ss wner s Manual Declaration of conformity Tanaka Kogyo Co Ltd 3 4 29 Tsudanuma Narashino Chiba Japan Declare under our sole responsibility that the product engine pump model TCP 25 381 to which this declaration relates is in conformity with the essential safety requirements of directives 89 392 EEC 91 368 EEC 93 44 EEC 93 68 EEC EMC89 336 EEC The following standards have been taken into consideration ISO 3864 EN 292 2 Manufactured at Chiba Japan Serial No up from V001001 Signature Seiji Tanaka Position Vice president www tanakapowerequipment com 9 custsvc tanaka ism com
9. turn spring e Clean the exterior of the spark plug e Remove the spark plug and check the electrode gap Adjust it to 0 6 mm 024 or change the spark plug e Clean the cooling fins on the cylinder and check that the air intake at the starter is not clogged e Clean the air filter Monthly maintenance e Rinse the fuel tank with gasoline and clean fuel filter e Clean the exterior of the carburetor and the space around it e Clean the fan and the space around it www tanakapowerequipment com 7 custsvc tanaka ism com Tanaka 6 Technical Data TCP 25 210 381 Owner s Manual Model TCP 25 210 TCP 381 Engine Type High torque 2 cycle single cylinder E Size 22 ml 51 ml Max Power 0 75 kW 8 000 min 1 65 kW 5 500 min Carburetor System Walbro diaphragm Float type Ignition System Electronic a Spark Plug NGK BPM 7A or BPMR 7A NGK BM 6A or BMR 6A Fuel Tank Capacity 0 75 1 2 Pump Max Capacity 120 I min 300 min Max suction height 8m 5m Max delivery height 35m 40 m Connection diameter 1 25 4 mm 1 5 38 mm Dry weight 5 1 kg 9 5 kg Overall dimensions L x W x H 287 x 219 x 288 mm 398 x 300 x 382 mm Sound pressure level dB A 85 1 91 1 Sound power level dB A 91 9 98 3 NOTE Equivalent noise level vibration level are calculated as the time weighted energy total for noise vibration levels under various working condi
Download Pdf Manuals
Related Search