Swisher LS728 User's Manual
Contents
1. WARNING DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND HYDRAULIC RESERVOIR See separate Engine Manual for fuel and oil recommendations Your log splitter has come equipped with a fuel shut off valve for towing purposes Before starting engine make sure crankcase 1s filled correctly with oil and the proper fuel has been used The engine will only start when the throttle lever and fuel shut off valve are turned to their ON positions COLD WEATHER START UP The Cold Weather Clutch enables the engine to be started without having to pull through cold thickened hydraulic fluid Simply pull the handle out into locked position Start engine let it warm up and release Cold Weather Clutch After starting assure that the lever has reengaged OPERATION TOWING This unit should not be towed on any street highway or public road without checking the existing federal local and state laws Any licensing or modifications such as taillights etc need to comply with existing federal local or state vehicle requirements is the sole responsibility of the purchaser Obey all regulations when towing on public roads and highways See also TOWING SAFETY Be sure you are using the correct ball hitch size for the hitch coupler on the log splitter 2 ball Be sure safety chains are properly connected Leave enough slack in chains for turning See TOWING SAFETY to read warnings about coupling Make sure beam attachment is locked in the2. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state This is a limited warranty as defined by the Magnuson Moss Act of 1975 WARRANTY SAFETY TOWING OPERATION TABLE OF CONTENTS MAINTENANCE DECALS PARTS BREAKDOWN SPECIFICATIONS gt gt SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual When you see this symbol carefully read the message that follows and be alert to the possibility of personal injury Read this manual completely This machine can amputate hands feet and throw objects Failure to observe the following safety instructions could result in serious injury or death WARNING The engine exhaust from this product contains chemicals known to the state of California to cause cancer birth defects or other reproductive harm DANGER Your log splitter was built to be operated according to the rules for safe operation in this manual As with any type of power equipment carelessness or error on the part of the operator can result in serious injury If you violate any of these rules you may cause serious injury to yourself or others e Read the manual Learn to operate this equipment in a safe manner e Do not under any circumstances a
3. horizontal position NEVER tow splitter in the vertical position Turn the fuel shut off valve OFF to prevent flooding of the engine while traveling TOWING AT NIGHT The requirements for taillights are based on States regulations Some states allow towing at night as long as the towed equipment does not visibly impair the tow vehicle taillights This is based on a state to state requirements The customer is responsible for meeting the states requirements If a Statement of Origin is required in your state see your local dealer to receive one OPERATION 1 Set up the log splitter in a clear level area and block the wheels The suction port on the tank should always be on the lower side of the log splitter 2 Place a log on the beam against the foot plate Make sure the log is securely on the foot plate and up against the beam 3 Depress the valve lever so that the cylinder will drive the wedge into the log Extend the cylinder until the log splits or to the end of its stroke If the log has not completely split after the cylinder has reached the end of its extension retract the cylinder NOTE Leaving the valve in the actuate position at the end of the stroke may damage the pump OPERATING POSITIONS WARNING THE LOG SPLITTER BEAM IS HEAVY AND CAN PINCH HANDS FINGERS IF CARE IS NOT TAKEN STANDARD HORIZONTAL TO VERTICAL The Standard Splitter has 2 operating positions Horizontal Vertical Remove pin from below be
4. AL OPERATOR S INSTRUCTIONS READ OPERATOR S MANUAL 1 Place log splitter on flat dry solid ground 2 Lock in either the Horizontal or Vertical position Splitting Wedge Control Handle Block tires to prevent rolling Set the engine throttle at maximum speed Place the log against the end plate Stabilize the log when needed on its side NEVER on the end between the log and the splitting wedge Only one adult should stabilize the log and operate the control Move the control handle in the splitting direction Release the control handle to stop the wedge movement Move the control handle gt al the splitting direction to return the wedge Vertical Position Lock Qo EN PD mmo OD03 OPERATOR INSTRUCTION DECAL VERTICAL ADANGER HORIZONTAL POSITION AVOID SERIOUS INJURY OR DEATH READ OPERATOR S MANUAL POSITION Keep hands away rom wedge end plate partly split wood and moving parts Hold log on its side not on ends Only one operator permitted Adult who loads and halds log must be the one who operates control handle Keen bystanders helpers and children at least 10 feet away High pressure fluid can escape through a pin hole leak and cause serious injury by puncturing the skin and causing blood poisoning Never check for leaks with your hands Operate the log splitter on level surface Lock in vertical or horizontal position Wear protective work glaves safety shoes and safely goggles Watch you
5. E ON ALL MODELS DESCRIPTION Beam Weldment Wedge Weldment Wedge GIB Angle Bolt 3 8 16 X 1 1 4 Carriage 5 g Ni38d6Nyo NBIB2 8 Nuigi3NyeoJam NBi i 8 Ram Cylinder S722 Model TR Ram yinder L810828 and LS728 Model 7354K 3 Way Pipe Nipple 7292 12 ENGINE DETAIL LS10525 MODELS AAA Ae NA 2 BUITETBXTVMSer Flange NER 4 pper Spacer 838 3 ngine Pulley BB 6 LowrSpcer BBi058 7 Washer Ro AE Washer Belleville 609 9 Bolt 7 16 20X1GR5whloctie NB452N m 1 4 X1 Keystock 9031 253 D 9 C NOTSHOWN Fuel Shut Off Valve Inline 7414 NOTSHOWN Fuel Line Clamp 6FLC ENGINE DETAIL LS722 and LS728 MODELS Enge NA 2 f ANGIE AZ 14 Sem Fang MB L 4 Nesne Sem Fange Nero 8 IX Keystock 9000 9 AZ Set Screw wiLoctie NB3I2 7 EngnePuly7i iD aa A Wester Beenie 5 a 13 14 SPECIFICATIONS Splitting garen 22 Tons 28 Tons 28 Tons Force 7 Hp Briggs and 10 5 HP Briggs 7 Hp Briggs and Stratton Intek OHV and Stratton I C Stratton Intek OHV Splitting Horizontal and Horizontal and Horizontal and Positions Vertical Vertical Vertical Cylinder Size 4 X24 4 1 2 X24 4 1 2
6. RMATION AVAILABLE PRODUCT SWISHER LOG SPLITTER SERIAL NUMBER MODEL NUMBER ENGINE MODEL NUMBER PART NUMBER PART DESCRIPTION www swisherinc com TELEPHONE 1 800 222 8183 FAX 1 660 747 8650 SWISHER MOWER amp MACHINE CO INC 1602 CORPORATE DRIVE WARRENSBURG MO 64093 SWISHER MOWER amp MACHINE CO INC 16
7. X24 2 Stage with Heavy 2 Stage with Heavy 2 Stage with Heavy Duty Bearings Duty Bearings Duty Bearings Pump 11 Gallons Per 16 Gallons Per 11 Gallons Per Specs Minute Minute Minute Valve Auto Return Auto Return Auto Return Belt Drive 1 1 Ratio Belt Drive 1 1 Ratio Belt Drive 1 1 Ratio with Clutch for with Clutch for with Clutch for T m Easy Starting Easy Starting Easy Starting 16 Quarts 17 Quarts 17 Quarts capacity 999 25 25 25 Drive Maximum Log length 4 00 X4 80 X8 4 00 X4 80 X8 4 00 X4 80 X8 Tire Specs with High Speed with High Speed with High Speed Bearings Bearings Bearings Metal No No No Fenders Unit 450 Lbs 490 Lbs 465 Lbs Weight 15 SWISS HER A TRADITION OF QUALITY SINCE 1945 OWNER S MANUAL MODEL NO LS722 LS10528 LS728 LOG SPLITTER HOW TO ORDER REPAIR PARTS Each Log Splitter has its own serial number Each engine has its own serial number The serial number for the Log Splitter will be found on the right hand side of the hydraulic oil reservoir The serial number for the engine will be found on the top of the blower fan housing All Log Splitter parts listed herein may be ordered directly from Swisher Mower amp Machine Co Inc your nearest Swisher dealer or from our website All engine parts may be ordered from the nearest dealer of the engine supplied with your log splitter Parts subject to change without notice WHEN ORDERING PARTS PLEASE HAVE THE FOLLOWING INFO
8. am Do not remove bolt and nut Rotate beam into vertical position and pin so beam cannot fall into horizontal position DO NOT TOW IN VERTICAL POSITION IMPORTANT When operating splitter in wooded areas obtain a spark arrestor for the exhaust system See your local engine dealer When preparing logs cut ends as square as possible The maximum length of any logs should be only 24 MAINTENANCE amp STORAGE A WARNING Disconnect spark plug before performing any maintenance or making adjustments RESERVOIR FLUID Check the hydraulic fluid level in the reservoir tank before each use Operating without an adequate oil supply will cause severe damage to the pump Change the hydraulic fluid in the reservoir per manufacturers recommendations Be aware of the environment when disposing of used petroleum products Please dispose of used hydraulic fluid engine oil and any by products from the maintenance of your log splitter at approved recycling centers Should it become necessary to loosen or remove any hydraulic fitting or line be sure to remove all pressure by shutting off the engine and moving the control handle back and forth several times NEVER remove the cap from the hydraulic tank or reservoir while your unit is running Hot oil under pressure will cause injury Always store gasoline in an approved tightly sealed container Store container in a dry cool place Keep fuel away from gas appliances where fumes could contact open
9. c could cause an accident Never operate or allow someone to operate this equipment while under the influence of alcohol or drugs Always block the wheels to prevent movement while using splitter Never operate your splitter on wet muddy or icy surfaces Safe footing is essential in preventing accidents Never operate your splitter while it is attached to the tow vehicle Never make adjustments or repairs with the engine running Never attempt to split woods across the grain Some types of wood may burst or fly out of your splitter and result in injury Both ends of the log should be cut as squarely as possible to prevent the log from sliding out of the splitter during operation Log length should be kept to 24 or less TOWING SAFETY e Do not allow persons to ride on splitter Do not carry any cargo or wood on your splitter It may fall off and endanger vehicles that are following you e Be sure support leg is in the travel position and coupling secure This must also be retracted so not to interfere while towing Retract support leg by removing pin sliding up and replacing pin e Never exceed 45 MPH while towing your splitter Be extra cautious when traveling over rough terrain especially over railroad tracks e Always be careful while backing your splitter You could jackknife your log splitter if not careful e Before using splitter disconnect it from tow vehicle A log could easily be POSITION pushed forward into th
10. e vehicle e See tire and wheel specifications for PSI while towing e Beaware of the extra length of splitter while turning parking crossing intersections and in all driving situations OPERATION INSTRUCTIONS POSI LOCK COUPLER ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE PLACE HANDLE IN LOCKED POSITION WITH BALL IN COUPLER TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT COUPLER IS NOT LOOSE ON BALL CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE TO OPEN PULL UP ON COUPLER HANDLE AND ROTATE FORWARD PLACE COUPLER ON BALL WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET ROTATE COUPLER HANDLE BACKWARD UNTIL HANDLE IS IN LOCKED POSITION AFTER TOWING FOR 50 MILES CHECK COUPLER FOR TIGHTNESS ON BALL ALWAYS CHECK TIGHTNESS BEFORE TOWING BE SURE COUPLER HANDLE IS IN LOCKED POSITION WARNING NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS ALWAYS USE CORRECT BALL SIZE MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER LOCK COUPLER HANDLE SECURELY BEFORE TOWING ALWAYS CHECK FOR DAMAGES AND REPLACE IF DAMAGED AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING OPERATION Intended use This log splitter is intended and designed to only split wood NEVER use for any other purposes Doing so can cause injury or VOID THE WARRANTY ASSEMBLY INSTRUCTIONS This log splitter has been partially assembled at the factory Refer to the drawings and part lists should
11. ed to ninety 90 days from the date of original purchase This warranty applies only to products which have been properly assembled adjusted and operated in accordance with the instructions contained within this manual This warranty does not apply to any product of Swisher Mower Co Inc that has been subject to alteration misuse abuse improper assembly or installation shipping damage or to normal wear of product Excluded from this warranty are normal wear normal adjustments and normal maintenance The pump valve and cylinder each carry separate manufacture s warranties The valve and cylinder both carry a one 1 year limited warranty The pump carries a two 2 year limited warranty In the event you have a claim under this warranty you must return the product to an authorized service dealer All transportation charges damage or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser Should you have any questions concerning this warranty please contact us toll free at 1 800 222 8183 The model number serial number date of purchase and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any warranty claim can be processed THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES
12. ent before starting to work with this machine Fluid escaping from a very small hole can be almost invisible Do not check for leaks with your hand Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury Leaks can be located by passing a piece of cardboard or wood over the suspected leak and looking for discoloration IF injured by escaping fluid see a doctor at once Serious infection or reaction can develop if proper medical treatment is not administered immediately Split only one log at a time Never attempt to split two logs on top of each other Do not straddle or reach across the splitting area while operating the splitter Do not step over splitter when the engine is running You may trip or accidentally activate the splitting wedge Walk around to get to the other side Never place hands or feet between log and splitting wedge or between log and ram during forward or reverse stroke Never attempt to load splitter while splitting wedge is in motion When loading log splitter place hands on the sides of the log not the ends Only use your hands to operate the control lever Never use foot knee rope or any extension device Always keep fingers clear of splits that open in log during splitter operation When splitter is in the return mode keep hands off the machine Only operate splitter on level ground not on the side of a hill It could tip or rolling logs poor footing et
13. flame pilot lights or sparks Do not operate your splitter in poor mechanical condition or when needing repair Repair and replace worn or broken parts immediately Periodically tighten nuts bolts and hydraulic fittings The hydraulic system of your log splitter requires careful inspection along with the mechanical parts Be sure to replace frayed kinked or otherwise damaged hydraulic components The pressure relief valve on the splitter is preset at the factory Do not adjust valve Only a qualified service technician should perform this adjustment If the wedge becomes dull or nicked it can be removed and sharpened The wedge is heavy and may still have sharp edges wear gloves while handling the wedge REPAIR PARTS Your Swisher Log Splitter has been produced with components designed specifically to this machine Although standard springs hardware etc may look similar to parts used on other machinery they may in some cases be made of a different construction and or materials SAFETY DECALS Replace decals immediately if damaged COLD WEATHER CLUTCH TR Shut off fuel for transport Failure to do so may cause unit to flood OD16 FUEL SHUT OFF DECAL OD07 COLD WEATHER DECAL PULL LOCK NOTICE HYDRAULIC FILL PLUG Maintain level of hydraulic oil at 3 below the plug Recommended to use universal hydraulic oil or Dextron A Transmission fluid OD12 HYDRAULIC FILL PLUG DECAL VERTIC
14. it become necessary to disassemble the unit for repair or replacement of parts Inspect all components for damage WARNING Exercise extreme caution as parts are very heavy Sufficient persons or mechanical handling equipment should be used IMPORTANT This unit is shipped with oil but without gasoline in the engine After assembly see separate Engine Manual for proper fuel and oil recommendations FILLING THE HYDRAULIC RESERVOIR Fill the hydraulic reservoir with at least 12 Quarts of Dextron III Automatic Transmission fluid or 10W AW hydraulic fluid After the hydraulic reservoir and the engine crankcase are filled correctly with their respective oils start the engine Remember to set the throttle and turn on the fuel shut off valve The hydraulic pump should prime itself With the engine running move the hydraulic valve lever toward the wedge This will cause the cylinder to extend and expel air When the cylinder is fully extended retract it Repeat this procedure several times An erratic movement of the cylinder indicates that there is air in the system Once the cylinder has a smooth and constant speed indicating that all air has been expelled add another 4 quarts of oil this should then bring the fluid level up to approximately 3 below the fill hole These models require approx 16 17 Quarts of hydraulic fluid NOTE If the tank is overfilled it will tend to expel oil from the breather cap when the cylinder is retracted START UP
15. lter this log splitter This equipment was designed and engineered in accordance with operating instructions Altering this equipment or using this equipment in such a way as to circumvent its design capabilities and capacities could result in serious injury or fatality and WILL VOID THE WARRANTY e Allow only responsible adults who have read this manual to operate this machine Never allow children to operate this machine e Never use splitter for any other purpose than splitting wood Any other use can result in injury Your splitter is a precision piece of power equipment not a toy Therefore exercise extreme caution at all times e Only a single operator is to load and operate the log splitter Keep all others including pets and children a minimum of 20 feet away from your work area More accidents occur when more than one person operates the log splitter than any other time e Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug to prevent accidental starting the engine when setting up transporting adjusting or repairing e Always wear protective gear such as safety goggles protective hearing device steel toed shoes and tight fitting gloves without drawstrings or loose cuffs e Never wear loose clothing or jewelry that can be caught by moving parts of the splitter and pull you into it Keep hair away from moving parts e Familiarize yourself with all of the controls in a safe environm
16. r footing e Never operate under the influence of alcohol or drugs e Do not refuel a hot or running engine OD09 DANGER POSITION LOCK DECAL SEE ENGINE DETAIL rum SEE BEAM DETAIL ASSEMBLY DETAIL LS722 LS10528 LS728 MODELS 10 SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts Color cannot be guaranteed upon service parts 6 BaiWA13X4GR8 NR 8 Taro ResemewTank naom 8 X12 Hitch Pin wiHair Pin NB648 A HyduicPumpi8108 8 LS2002B 3 9 Moor Base O O O O o 22 Support Leg Bracket MRS 28 S8X2i2SafyH chPi I Hii 34 Togu RO 35 Boeson NA 30 SweyChamwlHok e sed PumpPuley 7308 38 SH amp 18X1SetScrewwiole NB812 AR Bm 35 Boeie O NO 38 WeBuhig 087 A BeaigSea DE AR Taper Bearing O O 22038 48 We amp Whel 7296 L 49 Washer BAD X11 400 100A N 89 ROBO 82 Wheel Dust Cover SSC 11 BEAM DETAIL ALL MODELS NOT ALL PARTS AR
17. swisherinc com OWNER S MANUAL MODEL NO LS722 STARTING SERIAL ss LOG LS728 STARTING SERIAL L206 010001 Safety IMPORTANT Read and follow all Safety Assembly Precautions and Instructions Operation before operating this equipment Service and Adjustment Rev 06 010 Repair Parts 1602 CORPORATE DRIVE WARRENSBURG MISSOURI 64093 PHONE 660 747 8183 Made In The FAX 660 747 8650 U S A Manufacturing quality lawn care equipment since 1945 11253 LIMITED WARRANTY The manufacturer s warranty to the original consumer purchaser is This product is free from defects in materials and workmanship for a period of two 2 year from the date of purchase by the original consumer purchaser We will repair or replace at our discretion parts found to be defective due to materials or workmanship This warranty is subject to the following limitations and exclusions 1 Engine Warranty 2 Commercial Use 3 Limitation 4 Exclusions All engines utilized on our products have a separate warranty extended to them by the individual engine manufacturer Any engine service difficulty is the responsibility of the engine manufacturer and in no way is Swisher Mower Co Inc or its agents responsible for the engine warranty The Briggs amp Stratton Engine Service Hot Line is 1 800 233 3723 The Tecumseh Engine Service Hot Line is 1 800 558 5402 The warranty period for any product used for commercial or rental is limit
Download Pdf Manuals
Related Search