Sunfire TGR401 User's Manual
Contents
1. Theater Grand Receiver TGR 401 TGR 401 230 g User s Manual RISK OF ELECTRIC SHOCK DO NOT OPEN i CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Important Safety Instructions 1 Read Instructions 2 Keep these Instructions 3 Heed all Warnings 4 Follow all Instructions 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not install near any heat sourc es such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 8 Unplug this apparatus during light ning storms or when unused for long periods of time 9 Refer all servicing to qualified ser vice personnel Servicing is required when the apparatus has been dam aged in any way such as a power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped z 10 Ventilation The apparatus should be situated so that its location or position does not interfere with its proper ventilation For example the apparatus should not be situated on a bed sofa rug or similar surface that may block any ventilation openings or placed in a built in installation such as a bookcase cabinet or c2. 10 Theater Gra1 d Receiver DIGITAL SOURCE 16 4 11 TGR 401 MUTE 17 Display This display shows which input is selected the volume level sur round mode and other features such as the setup menus Input Press this button then cycle through the inputs with the manu al selector 9 The LED will light Mode Press this then cycle through the various modes with the manual selector 9 The LED will light Setup Press this then cycle through the available setup items with the manual selector 9 Press enter 8 to select the required setup item Press Input 5 or Mode 6 to exit the setup menus The LED will light when in setup mode Enter Use this and the manual selector knob 9 during setup 7 When a desired menu item is found press enter to select that item Note Setup 7 and Enter 8 can be used to increase or decrease dB values within the menus and DIpoLbY DIGITAL EX PRO LOGIEM E des dies SIRIUS HDMI Eee O 18 used for other things such as to change the letters of a source name for example Manual Selector Use this to cycle through the various menu items such as the inputs when input 5 is pressed the modes when mode 6 is pressed and setup when setup 7 is pressed 10 Mute 11 This turns off the sound Press it again or adjust the volume control to return to the previous vo
3. and posite video depending Optical S Video EQ mic LED on the mode button Input Input Input SVID EQMIC Measurement microphone 11 CHAPTER 1 Rear Panel Features 3 4 5 COAXI COAX2 COM Op ORO ya L sul S OOOOOC IRED UNDER sense FROM DOLBY LABORATORIES DOLBY PRO LOGIC AND THE DOUBLE MBOL ARE TRADEMAE Ole USECLASS 2 WIRING IR INPUTS IR OUTPUTS O wet 2lour E Y 6123 MINIMUM 4 OHMS SPEAKER IMPEDANCE 8 OHMS FI TRIGGER OUT TO AC FUSE emma POWER i 0 En LI MDA15 12 FUSE 1 AM Antenna These connections are for the supplied AM loop antenna FM Antenna The supplied FM antenna fits this F type coaxial connector Other antennas can be fitted for im proved reception SIRIUS Connection This connection is provided for the optional SIRIUS tuner kit SC H1P1 This consists of an antenna for picking up satellite ra dio transmissions and a tuner unit that connects here The connec tion allows left and right audio and control data to enter the TGR 401 The OSD menus of the TGR 401 allow you to select your favorite SIRIUS Satellite radio stations as presets for easy recall See page 63 for more details Audio Video These audio composite video and S video inpu
4. IEC Line Cord Socket The TGR 401 comes with a detachable linecord that connects here Plug the line cord into an AC wall socket or power strip that is cor rectly configured with the voltage specified for your model 17 AC Line Fuse Always unplug the linecord from the AC Mains before checking or changing the fuse If this fuse blows you must replace it with a fuse of exactly the same size and current rating 18 Power Switch If this is switched off the TGR 401 will be off and cannot be turned on even with the front panel power switch the remote control or optional Ol 2SF touchpads In normal operation leave this switch on Turn it off if you will not be using the TGR 401 for extend ed periods 13 CHAPTER 1 Installation Observe the following precautions when choosing a location for your TGR 401 Make sure the TGR 401 has good ventilation Do not cover any of the ventilation slots or fit the receiver inside a sealed cabinet without good air flow e Protect it from prolonged exposure to direct sunlight and other direct sources of heat such as heating vents and radiators e Do not expose the unit to rain or moisture If fluid or a foreign object should enter the unit immediately turn off the power and contact your Sunfire Dealer e Avoid excessive exposure to ex treme cold or dust e Do not place heavy objects on top of the unit AC Power Considerations Ensure that
5. S video component video and HDMI Choose component or S video if your video system supports it as this will give better picture quality than com posite video When an audio video component is selected the audio will play in your system and the video will be switched to a video input of your TV monitor You must have the TV connected in order to see the On Screen Display OSD No OSD is available on HDMI Sunfire User s Manual CHAPTER 2 System Configurations The following pages show some typical connections that you might make in your installation They show how the inputs and outputs of the TGR 401 are connected to various audio and video components Analog Audio and Composite Video VCR Composite video signal from Sy TGR 401 MON composite video output to TV Monitor s composite video input gt g VCR Player A Composite video signal When this input is selected from the a Hee Oe ees input Analog audio signals front panel or the remote control the i AR From VCR audio outputs VCR s audio will play in your system To TGR 401 IN1 L R audio inputs nope and the video is sent to the TV As with all the video connections that follow you must make sure that your TV monitor is set to look at its correct video input or you will not see the picture If your TV and other video compo nents have S Video connections use them as they provide better picture quality t
6. par les ministere des communications du Canada WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRO DUIRE LALAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED IN ARTICLE 810 RADIO AND TELEVISION EQUIPMENT GROUND CLAMP GROUND CLAMPS SERVICE ENTRANCE EQUIPMENT GROUND CLAMPS a ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE NOTE TO CATV INSTALLER This reminder is to call the CATV system installer s attention to Article 820 40 of the NEC that provides guide lines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical OUTSIDE ANTENNA GROUNDING If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 7
7. setup or manual setup is finished and any EQ adjustments made the TGR 401 is setup correctly and ready for action If you play a Dolby Digital or DTS encoded source the TGR 401 will au tomatically select the correct surround mode If it is a 2 channel source you can select a surround mode using the remote s MODE buttons or from the front panel The TGR 401 has many more options that are described in further detail in this manual These options will help you customize the TGR 401 to suit your tastes You can do this after you have used the TGR 401 for a while and have a better idea of how you would like to customize your system CHAPTER 1 Front Panel Features 1 2 3 4 MAIN ZONE2 SONIC HOLOGRAPHY SELECT SELECT ZONE CONTROL TU 12 13 14 15 1 Power This button turns the TGR 401 on fully powered up or into Standby mode asleep but can be turned on remotely The blue LED above the power switch is on when the TGR 401 main zone is turned on When the TGR 401 is turned off the LED will turn red To fully turn off power to the TGR 401 for example if you are going on vacation for a week or two then use the rear panel power switch Press Zone 2 select 14 followed by this power button to turn on Zone 2 Main LED This blue LED is on when the Main zone is on It flashes red when the remote control is used Zone 2 LED This green LED is on when Zone 2 is on
8. the TGR 401 by pressing the TG401 button THEATER GRAND SERIES The VOL and MUTE buttons will control the TGR 401 no mat ter which source component the remote is set to operate The PUNCH command allows you to change this if required see page 28 Turn down the TGR 401 volume and use the remote or front panel to select a video source as fol lows If you have followed step 9 the remote now shows the inputs that can be selected Select one From the TGR 401 front panel you can first press the input but ton center top and then rotate the knob to select the desired input 12 Play a source such as a DVD and bring up the volume to suit your taste Make sure the video can be seen in the TV monitor 13 Stop or pause the source The TGR 401 now needs to be set up correctly to suit your speakers and system This is done using the TGR 401 on screen display OSD menus It can be done either automatically or manually as can the EQ adjustment This needs to be done when you use your system for the first time or if you change anything such as the speak ers or their position Automatic Setup The TGR 401 comes with a mea surement microphone that plugs into the front panel microphone input Measurement microphone supplied The automatic setup procedure uses the microphone to measure and evaluate your system After the mea surements are complete the levels crossov
9. the unit is plugged into an outlet capable of supplying the cor rect voltage specified for your model Care If you need to clean the front sur face first turn off the power and then use a soft dry cloth rubbing with the grain Be careful not to scratch the display window 14 Connection Tips Before setting up your new system please consider the following e Always make sure that your components are all turned OFF or unplugged before making or changing any connections Whenever possible route the power cords away from the signal cables or speaker wires to prevent any hum or interference heard in the speakers Choose reliable hookup cables They should be fully shielded and as short as possible Use quality coaxial digital cables to connect the TGR 401 to any source equipment which has co axial digital outputs Some patch cords can be a very tight fit and there is usually a preferred method of getting them off Some have to be removed with a twisting action Be gentle or you may damage the jacks of your TGR 401 or other components Some audiophile cables should be hooked up in one direction these are usually marked with arrows It is usual for the right channel patch cord plugs to be red and the left channel connections to be white grey or black Composite video connections are usually yel low Video Connections The TGR 401 has four types of video connections composite video
10. 0 provides information with regard to proper grounding of the lead in wire to an antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See Figure above Sunfire User s Manual 3 CHAPTER 1 Contents Important Safety Instructions Chapter 1 Introduction Overview Quick Start Guide Front Panel Features Rear Panel Features Installation Chapter 2 System Configurations Chapter 3 Remote Control Chapter 4 On Screen Display OSD Chapter 5 Using the TGR 401 Input settings Bass Management Video Conversion Manual Setup Automatic Setup Procedure Automatic and Manual Equalization Surround Modes Sonic Holography FM and AM Tuner Operation Recording Zone 2 Operation Triggers Appendix Speaker Placement The RS 232 Port Troubleshooting Guide Remote Control Codes Specifications Default Input Table Optional VIA migo iPod Dock Optional SIRIUS Satellite Radio Tuner Optional Ol 2SF Touchpads Limited Warranty Service Assistance Read the Safety Instructions care fully before connecting and us ing your Sunfire Theater Grand Receiver TGR 401 Chapter 1 is a general introduction to the features details and installa tion of your TGR 401 Chapter 2 shows many options for connecting your source equipment to the TGR 401 Chapter 3 describes the details and operation of the advanced remote control Chapter 4 shows the various menus of the On Screen D
11. Always connect a separate digital audio input cable when using HDMI Preamp Outputs These line level audio outputs allow you to use external ampli fiers to power your loudspeakers There are outputs for L R C LS1 RS1 LS2 RS2 LB RB and SUB Speaker level Outputs These speaker level audio out puts connect to the input posts of your loudspeakers 8 CH Inputs These analog audio inputs can connect to the output of an ex ternal surround processor or a source component such as DVD Audio SACD or a DVD player Sunfire User s Manual CHAPTER 1 12 RS 232 Port with its own surround decoder Use the screw terminal input to You can select this as an input from the front panel or remote control The eight channels of analog audio will then pass into the TGR 401 Note if you use HD DVD or Blu ray DVD players that have 7 1 analog audio outputs use this 8 channel input It is fully processed in DSP with bass management speaker delays and tone controls Only the left right jacks are avail able in Zone 2 10 Digital Connections There are four S PDIF digital coaxial inputs with one coaxial output and four digital optical inputs with one optical output Use these with source equipment that has digital audio connections 11 TP1 and TP2 Optional Ol 2SF Film Interac tive touchpads are available for external control of Zone 2 or the Main Zone These wall mounted touchpads connect t
12. ails of the auto EQ and manual EQ adjustment are shown on page 41 OSD Menus The SPEAKERS menu is used to run the auto setup manual setup and EQ adjustment 1 Press the MENU button on the re mote to bring up the MAIN MENU of the OSD on your TV 2 Use the navigation pad left right up and down buttons to navigate through the menus in the next steps Sunfire User s Manual MAIN MENU TRIMS TONE CONTROLS MODES PRESETS SETUP SETUP INPUTS SPEAKERS VIDEO MAIN ZONE ZONE 2 CONTROL DIGITAL OUT DN MIX THRU DIMMER LOW MEDIUM HIGH SPEAKERS AUTO SETUP SPEAKER SIZE DISTANCE Ll LEVEL CALIBRATION EQ BINDING POSTS NOTE Quit the OSD at any time by pressing the nearby EXIT but ton Any changes will be saved There is no need to navigate back through previous pages unless you want to make more changes The TGR 401 front panel display shows the same messages as the OSD In the MAIN MENU select SETUP and from there select the SPEAKERS Menu In the SPEAKERS menu are the options for AUTO SETUP SPEAKER SIZE DISTANCE LEVEL CALIBRATION and EQ When you have finished the setup and or EQ adjustment press the remote s EXIT button to quit the OSD CHAPTER 1 Auto Setup see page 40 Manual adjustments see page 39 Manual or Auto EQ adjustment see page 41 Conclusion Once the automatic
13. ate your system correctly 000 000 QO a Sunfire The remote can also be used to activate and control all features of the second zone The TGR 401 230 is the export Use the center three buttons to se model set for 220 240 VAC operation lect either the input mode or setup Its operation is identical to the TGR menus Then use the input and menu 401 described in this manual selection knob to find the item In the setup menu rotate the knob to move through various menu items and press the nearby enter button to select an item Power Input on off mode and Input and Volume setup menu select adjustment Segre Theater Grand Receiver TERM eS SSS a INPUT i 1 mue oO o er SOURCE DOIDOLBY dts er baana SIRIUSH HDMI PRO LOGIC iix ES Neo 6 96 24 Headphones IRwindow Zone Sonic Sliding cover l choice Holography for front inputs and microphone input Select MAIN then any commands that follow o will affect that zone Select Sonic Holography for an enhanced 3D image Select Zone 2 then any commands that fol of any source low within several seconds will affect Zone 2 It returns to Main Zone control after several seconds of inactivity 7 Sunfire User s Manual CHAPTER 1 Quick Start Guide We hope that the following details will help you get started using your TGR 401 1 Take care to read and fo
14. er frequency and delay times of the speakers are automatically adjusted for the best performance Any problems with the speakers are indicated for example it will let you know if there is low output from a speaker or if the polarity is reversed Details of the auto setup are shown on page 40 Alternatively you can use the manual procedure to set up your system Sunfire User s Manual Manual Setup There are three main manual ad justments that can be made using the SPEAKERS OSD menu 1 The SPEAKER SIZE menu al lows you to enter the crossover frequency of each speaker Using bass management any bass below the crossover frequency will be redirected to your subwoofer 2 The LEVEL CALIBRATION menu allows you to adjust the level of each speaker until they are all playing at the same level The level calibration test tones are also a quick way to check that all your speakers are working 3 The SPEAKER DISTANCE menu allows you to enter the distance that each speaker is away from your listening position The TGR 401 then calculates the delay times Details of the manual setup proce dure are shown on page 39 EQ Adjustment The measurement microphone can also be used to measure the system response and adjust the EQ auto matically This will provide a smooth response and remove room effects Alternatively the EQ of pairs of speakers or all speakers can be ad justed manually to suit your taste Det
15. han composite video 15 Sunfire User s Manual CHAPTER 2 16 Sunfire User s Manual
16. isplay and how to adjust and customize your TGR 401 Chapter 5 describes the available modes options and operational details of the TGR 401 The Appendix shows some ad ditional information including a troubleshooting guide optional components the warranty and service assistance details To find out more about this and other Sunfire products please visit our website www sunfire com Sunfire User s Manual CHAPTER 1 Introduction Thank you for purchasing a Sunfire TGR 401 Theater Grand Receiver We hope that you enjoy it and the music it makes as much as we have enjoyed creating it for you As with our entire line of products the TGR 401 is brimming with exclu sive high performance technologies that deliver powerful movie and music experiences These include the follow ing features Amplifier e Patented Tracking Downconverter power supply 7 x 200W into 8 ohms with no more than 0 5 THD Features e SIRIUS ready AM FM tuners with RDS feed back e VIA migo support for native iPod control via OSD and front panel Two touchpad ports for optional Ol 2SF Film Interactive touch pads Feedback for functions and metadata from SIRIUS and iPod Automatic setup and room cor rection w included microphone e Input volume matching e A V sync to match audio to video Connections 4 Analog inputs 2 outputs e 4 Video inputs 2 outputs e 4 optical digital inputs 1 out
17. ld be referred to qualified service personnel PORTABLE CART WARNING Carts and stands The Component should be used only with a cart or stand that is recommended by the manufacturer A Component and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the Component and cart combination to overturn Sunfire User s Manual 16 To prevent electric shock do not use this polarized plug with an exten sion cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure Pour pr evenir les chocs lectriques ne pas utiliser cette fiche polarise avec un prolongateur un prise de courant ou une autre sortie de cou rant sauf si les lames peuvent tre ins r es fond sans laisser aucune parlVe d couvert 17 Grounding or Polarization Precautions should be taken so that the grounding or polarization means of the Component is not defeated This apparatus does not exceed the Class A Class B whichever is ap plicable limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Ca nadian Department of Communications ATTENTION Le pr sent appar eil num rique n met pas de bruits radio lectriques d passant las limites applicables aux appareils num riques de class A de class B selon le cas prescrites dans le r glement sur le brouillage radio lectrique dict
18. llow the safety instructions on pages 2 3 Also make sure that you read the notes and details throughout the manual especially notes marked with a warning triangle A 2 Add four new AAA batteries to the remote control 3 Connect your source equipment and speakers to the TGR 401 Make sure that all of your equip ment remains unplugged from the AC mains until you have made all the connections 4 In your DVD player s Audio setup menu set the digital output to BITSTREAM If this is not set correctly the TGR 401 cannot decode the digital information for 5 1 surround sound playback 5 The TGR 401 s bass manage ment system allows the bass from each speaker to be redirected to a subwoofer Larger speakers can play the full frequency range and smaller speakers such as satellite types can have their bass redi rected See page 38 for details Make a note of which speak ers you would like to play the full frequency range Large and those which will have their bass redirected Also make a note of the approximate distance of each speaker from your listening posi tion 6 The surround back speaker outputs can be used for powering surround back or Zone 2 speak ers See page 22 7 Turn on the TGR 401 and then turn on your TV and source equip ment 8 10 11 Press the remote MAIN button a few times to make sure you are on the Main Page 1 Menu in the remote s display Set the remote to operate
19. losed equip ment rack that may impede the flow of air through ventilation openings 11 Power Sources The apparatus should be connected to a power sup ply only of the type described in these operation instructions or as marked on the apparatus The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and main tenance servicing instructions in the literature accompanying the appliance 12 Power Cord Protection Pow er supply cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular at tention to cords at plugs convenience receptacles and the point where they exit the apparatus 13 Non use Periods The power cord of the apparatus should be un plugged from the outlet when unused for a long period of time 14 Object and Liquid Entry Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the apparatus 15 Servicing The user should not attempt to service the apparatus beyond those means described in this operating manual All other servicing shou
20. lume level Volume Rotate this manual control clock wise to increase the volume The level will appear in the front panel display Note that the control knob does not rotate when the remote is used When turning on a new source make sure the level is low such as 20 and increase it slowly Note When the TGR 401 is powered on the volume is set to what is was when it was turned off It can also be set to come on at a preset max or min volume see the Main Zone in the Setup menu Sunfire User s Manual CHAPTER 1 12 IR Receiver Window This window should be clean and free from obstruction for the remote control to work correctly 13 Main Select Any changes made after press ing this button will affect the main zone 14 Zone 2 Select Any changes made after pressing this button will affect Zone 2 If no changes are made for 8 seconds the unit reverts back to main se lect To turn on Zone 2 press this button first followed by the power button 15 Sonic Holography Engage this to add a three dimen sional effect especially to stereo listening 16 Digital Input This will light when a digital audio source is playing 17 Front Door Sliding this door to the left reveals the front input connections and the connection point for the sup plied measurement microphone This is an ideal place for connect ing video game consoles or video cameras The three RCA inputs can be e Left audio i
21. n right audio in and composite video in or ifthe mode button is pressed they can be Pb Pr and Y component video inputs the LED will light There is also a digital optical input and an S Video input The measurement microphone connects in the right hand corner during the auto setup and auto EQ procedures Sunfire User s Manual A LE RE cvi OPT WES The front input can be selected by Make sure that the volume the remote control or by the input AN level is turned down when button 5 and manual selector connecting headphones or 9 when playing a new source or making any changes This will help protect your hearing from damage Note The remote control has a FRTMD button front mode in the Main Zone and Zone 2 This works the same as pressing the front door panel Mode button changing the three front RCA inputs from L R composite video to component video inputs 18 Headphone output This is where to connect your headphones In the MODES menu of the on screen display the headphone output trim can be adjusted relative to the setting of the main volume level 11 Also in the MODES menu and with the remote you can select Dolby Headphone technology on or off Dolby Headphone technology enables you to experience the surround effects of a five chan nel six channel or seven chan nel soundtrack through standard stereo headphones Mode Component video inputs button or L R audio and com
22. o TP1 or TP2 using stan dard CAT 5 cable Please contact your Sunfire dealer for more information Use only touchpads that are recom mended by Sunfire Do not connect these ports A N to Ethernet or other com puter networks Sunfire User s Manual This communications port allows future updates of the software from Sunfire to be made to your TGR 401 It may also be used for control by 3rd party integration systems 13 VIA migo Port This port allows connection of a proprietary VIA migo iPod dock ing station system available from Sunfire Do not connect this port to Ethernet or other computer networks 14 Infrared IR These inputs and outputs are used in custom installations to control the Main Zone and Zone 2 from a remote location IR INPUTS IR OUTPUTS 1 O 12V G 1 2 0UT The Infrared IR Input on the TGR 401 utilizes Tip as 12V Ring as IR and Sleeve as Ground In order to correctly utilize standard two or three wire IR equipment the wiring needs to be connected as shown Standard IR Sensor connect standard IR distribution equipment such as an IR sensor for Main Zone or Zone 2 opera tion The screw terminals accepts bare wire connections 2 or 3 wire input and 2 wire output The remote sensors can be ina different room or your main room 15 Trigger Outputs These allow the TGR 401 to con trol the turn on of other trigger en abled equipment in your system 16
23. put e A coaxial digital inputs 1 output e 7 1 multi channel input e 7 1 preamp outputs RCA e Assignable HD ready front panel input CEA color standard gold plated binding posts Sunfire User s Manual Processing e Sonic Holography for enhanced imaging e Dolby Digital EX and ProLogic IIx e Dolby Headphone e DTS ES Neo 6 and DTS 96 24 e SourceDirect mode for DSP bypass Video e Sunfire designed 1080p HDMI v1 3a switching 3 in 1 out e 100 MHz component switching 3 in 1 out e Video upconversion to compo nent Integration features e Bi directional RS 232 input e 2 IR inputs 3 outputs e 3 Assignable 12V trigger outputs e On the fly powered Zone 2 speaker switching e Maximum and power on volume settings for Main and Zone 2 e Power on source setting for Main and Zone 2 e PC application for initial setup Ol 2SF touchpad programming and software upgrades e LR2 Surr2 configurable binding posts Miscellaneous e Long grain solid aluminum front panel e Elegant blue LEDs for visual feedback Removable IEC cord Remote control features e Fully backlit e Pre programmed for most brands of A V equipment e Learns commands from your other remote controls e Macro feature lets you program a sequence of control steps e Operates up to 19 components e Does not lose programming memory when changing batteries RF capable with optional MRF 260 RF base Optional accesso
24. ries See your Sunfire dealer or visit our web site for more information regard ing the following accessories e SRK 200 Rack mount kit e Ol 2SF touchpads e VIA migo iPod dock e SC H1P1 SIRIUS Satellite Radio antenna tuner kit MRF 260 RF remote control base Unpacking Your TGR 401 should reach you in perfect condition If you do notice any shipping damage please contact your Sunfire Dealer immediately Gently lift out the unit and remove all the packing material and acces sories It is important to save all the packing materials and the box in case your TGR 401 ever needs to be moved or shipped for repair Make sure that you keep your sales receipt It is the only way to establish the duration of your Limited Warranty and it may come in useful for insur ance purposes Please take a moment to fill out and mail the Sunfire Customer Response card Also read the serial number located on the rear panel and record it here Serial Purchased at 6 Sunfire User s Manual CHAPTER 1 Overview Most features of the TGR 401 can be operated by the remote control s TG401 section For the best Home Theater per formance you should calibrate your speakers and customize the TGR 401 settings for your system Press the MENU button on the remote control to activate the On Screen Display OSD This has several menus which will allow you to set up your speakers and calibr
25. ts connect to the outputs of your audio video com ponents When these inputs are selected the audio will be heard in your system and the video will be seen on the TV screen 12 Fixed audio output is available for example for stereo recording to a tape player independent of the TGR 401 volume A stereo audio Zone 2 output is also available S Video and composite video out puts are available for monitoring as well as a composite video out put for Zone 2 Note that the video sources you would like to play in Zone 2 must use composite video There is no video up down conversion in Zone 2 Component Video These inputs connect to the component video outputs of your video sources if they have this capability When these inputs are selected the TGR 401 will auto matically route any video signals going into these jacks to the com ponent video outputs Note that component video provides the best picture compared to compos ite or S video If your TV Monitor has component video inputs connect them to the TGR 401 s component outputs The TGR 401 can also up convert composite video and S video from the other inputs 16 17 18 HDMI Use these to connect any HDMI components you may have in your system Three are inputs and one is an output to your HDMI equipped TV This supports 1080p and HDMlv1 3a sources No on screen display or audio decoding inside the TGR 401 is available from the HDMI inputs
Download Pdf Manuals
Related Search