Summer Infant 07030A User's Manual
Contents
1. based on Figure F WARNING THE GATE SHOULD NOT OPEN OVER THE STAIRS Position upper stop plate onto upper latch plate so that stop plate wall faces stairs as show in Figure G Step 7 Locate upper latch with alarm and remove baitery Step 14 Assemble the spring onto compartment door with Phillips head screwdriver Install 2 AAA batteries the lower hinge post Place the lower included into back of unit as shown in Figure H Screw battery door hinge cap over the spring and lower back onto upper latch hinge spindle Slide the lower hinge cap into place and secure with a wood screw Ensure that the hinge is oriented as shown in Figure Q maximum Note You must maintain equal spacing between walls and outer most panel bars This space should not exceed 3 on either side NOTE If Panel B is not needed skip steps 15 and 16 Step 15 Align Panel B over Panel A allowing an approximately 2 gap Step 8 Snap upper latch with alarm onto upper latch plate assembly as between Panel B and the doorway shown in Figure I Secure in place with the four provided alarm screws Step 16 To use with an extension Panel B assemble as shown in Figure R Align the adjustment screw holes in the top rails of extension A and B with a minimum overlap of 2 post screw holes as shown in Figure R Insert the post screw receivers into two aligned holes insert and tighten post screws securely as shown in Figure S Now repeat this procedure for2. panels with a threaded end screw as shown in Figure X Step 13 Adjust the lower hinge spindle out until it can fit onto the hinge post on the lower hinge as shown in Figure P Place spindles of both hinges down into position simultaneously Step 20 Using the wrench tighten each 4 total spindle lock nut inward toward the gate until they are secure Do not over tighten Check to ensure that all connections are secure and that gate is properly installed OPERATION To open the gate without triggering alarm see Figure Y Push button on top of alarm unit This will delay alarm for 10 seconds Open gate by rotating the thumb latch on the upper latch Then lift gate out of the upper and lower spindle rests and swing open NOTE If you do not push the button on alarm unit alarm will sound until the gate is closed To close the gate Simply swing the gate and it should close shut automatically ALWAYS check that the latch is securely fastened that all connections are fastened securely NOTE If gate is not closed within 10 seconds alarm will sound for 3 minutes or until the gate is closed 2 Spindles adjustments are unequal Solution Although unusual some doorframes may be out of alignment In this case you may have to adjust the individual spindles to ensure that the gate is aligned properly Make sure that the upper latch spindle properly locks into the upper latch If the gate does not stay in posit
3. 07030A Please read the following instructions carefully Keep this instruction manual for future reference Tools required Two Phillips head screwdrivers not included and wrench included Summer 2 AAA batteries required included For technical support Call 1 800 268 6257 or e Mail customerservice summerinfant com WARNING Adult assembly required Keep small parts away from children when assembling For use with children from birth and up INSTRUCTION MANUAL SURE AND SECURE EXTRA TALL TOP OF STAIRS GATE WITH ALARM Thank you for buying the Sure and Secure Extra Tall Top of Stairs Gate with Alarm from Summer Infant This hardware mounted gate helps you create and maintain a secure environment for your child in most locations It is especially suitable at the top or bottom of stairs It has special hardware that allows you to install it so the hinged swinging door opens only in one direction away from the stairs The easy to use one handed latch is convenient if your hands are full It s fully adjustable to fit openings from 28 to 54 71 cm to 137 cm wide and 36 91 cm tall Please read all the instructions before installing the gate N WARNING important KEEP FOR FUTURE REFERENCE e Jo prevent serious injury or death securely install gate and use according to manufacturer s instructions e Never use with a child able to climb over or dislodge the gate e Never leave child unattended
4. are needed a Pre drill a hole in the wall 7 32 or 5 5mm drill bit b Insert the wall anchors included into the hole and with a hammer tap gently on the end until the wall anchor is flush with the wall Step 2 Mount the lower hinge using a single wood screw in the bottom position only marked in Step 1 Be sure that the hinge post faces up as shown in Figure B Step 3 Repeat the mounting procedure with the upper hinge at the top position marked in Step 1 Be sure that the hinge is assembled with the opening facing down as shown in Figure C Hinge A and Latch B Templates Compression Lower Hinge Lower Wall Cap Cups 2 Upper Hinge Spindle Lower Hinge Spindle Upper Hinge Lower Latch Lower Hinge Latch Spindles 2 Upper Latch Upper s e Assombly Latch Plate Upper Stop Plate ed Upper Latch with Alarm Wrench Step 4 Place the bottom of template B for the latches even with the floor and hold it straight and vertical while you mark the 4 screw hole positions for the latches as shown in Figure D Step 5 Separate Upper Latch Plate with Alarm from Upper Latch Plate by loosening four screws Mount upper wall plate using two wood screws in the top template position marked in Step 1 see Figure E SS ea Stairs O O Stairs OPTION A OPTION B Latch Latch m n R H Su j Kopens Hinge hinge Openst Step 6 Choose direction you want the gate to open
5. e Use only with the lock securely engaged e Do not use if any components are missing or damaged e This product will not necessarily prevent all accidents Proper adult supervision is required at all times e This product contains small parts Adult assembly required Exercise care when unpacking and assembling product e Make sure wall mounted gates are well anchored in a wall stud e Always close gate behind you A BATTERY WARNING e Do not mix old and new batteries e Do not mix alkaline standard or rechargeable batteries e Remove batteries when gate is stored for a long period of time or when batteries are exhausted e Dispose of exhausted batteries properly FEATURES amp COMPONENTS PANELA PANEL B Post Screw 4 sets Wood Screws 8 Wall Anchors 8 oe Threaded End Screws 2 ay Sn Se Se eee a aa Ae PERN anA ne 7 lg r s ij EST os ee eee i siad SET UP Step 1 Place the bottom of template A for the hinges even with the floor and hold it straight and vertical while you mark the 4 screw hole positions for the hinges as shown in Figure A Screws are provided for mounting the hinges and latches directly to wood If mounting into wallboard use the wall anchors and screws provided Z SAFETY WARNING IF INSTALLING GATE AT TOP OF STAIRS DO NOT MOUNT INTO WALLBOARD If you are mounting the gate to another surface purchase and use the appropriate hardware NOTE If wall anchors
6. ion it may not be installed properly as shown in Figure Z Remove and reinstall the gate making sure the gate is installed correctly as shown in Figure Z f N top view x 3 Uneven floor side view Solution Move hinges and latches so that gate remains level Never exceeding 3 from the bottom rail to the lowest point of the floor as shown in Figure AA 4 Side Gaps over 3 Solution Readjust panels sliding them out one more adjustment and then Not to exceed 3 readjust spindles on both sides Be To use without alarm certain to keep equal spacing on each Remove batteries Not to side never exceeding 3 as shown in exceed Figure AA 4 Troubleshooting 5 Alarm not sounding If the gate does not stay closed Solution If alarm does not sound at appropriate time check batteries 1 The upper latch spindle is not adjusted properly Solution Adjust the upper latch spindle by loosening the spindle lock nut with the wrench Make certain that the spindle is properly adjusted to fit in the upper latch spindle rest Secure the lock nut Make sure that the upper latch spindle is properly locked onto the upper latch with the thumb lock MAINTENANCE 1 Regularly check alarm unit to make sure batteries are working properly 2 Regularly check spindle lock nuts to make sure the gate is securely in place 3 Do not use the gate if any components are damaged or missing 4 Wipe surface with a damp cl
7. oth or sponge using mild detergent and warm water We at Summer Infant stand behind all of our products If you are not completely satisfied or have any questions please contact our Customer Service Department at 1 800 268 6237 or e mail us at customerservice summerinfant com hy visit us at www summerinfant com Summer Infant Inc 582 Great Road PO Box 829 Slatersville RI 02876 0899 USA 1 800 268 6237 2005 Summer Infant Inc Please retain information for future reference Summer Infant Europe LTD 20 Sparrows Herne Bushey Hertfordshire WD23 1FX UK 44 0 20 8420 4429 Colors and styles may vary MADE IN CHINA 8 05
8. the bottom two rails ensuring that they are securely tightened Step 9 Choose the lower cup whose larger side faces stairs Insert lower latch into lower cup and mount to wall using two wood screws at the bottom template position marked in Step 1 Be sure that the spindle rest opening faces up as shown in Figure J NOTE The remaining wall cup should be stored for future use Step 10 Measure the width of the opening where you intend to install the gate Please refer to the following pictures to determine the correct installation configuration Final size adjustment must be made by individually adjusting the spindles If opening is 28 30 5 wide only Panel A is needed If greater than 30 5 wide use Panel A and Panel B 28 30 5 with PanelA 30 5 54 with Panels A amp B Step 17 Screw upper and lower latch spindles into end of outermost panel as shown in Figure T and U Step 11 Screw the upper and lower hinge spindles into the hinge side of ends of Panel A s ends until they stop as shown in Figure M and N Step 18 Adjust the upper and lower latch spindles outward until they fit into the spindle rests on the latches as shown in Figures V amp W Do not over adjust spindles too tight against latches or gate will be difficult to open Step 12 Adjust the upper hinge spindle out until it can fit onto the hinge post on the upper hinge as shown in Figure O Step 19 Cap open ends of
Download Pdf Manuals
Related Search