Sub-Zero Drawer Microwave User's Manual
Contents
1. Installation 243 4 min 629 FLUSH INSET 11 4 DEPTH 32 J H SIDE CLEATS 31 2 89 x 2 51 ANTI TIP BLOCK 19 16 38 J uS xs JEN E 7 16 11 TOP CLEAT 143 4 375 1515 16 OPENING 405 281 2 724 HEIGHT FLUSH INSET OPENING WIDTH HEIGHT L L 1 25 SIDE CLEATS 11 16 17 PLATFORM 36 914 12 25 635 gt STANDARD 303 8 772 CABINET DEPTH FLOOR TO FLUSH INSET WIDTH COUNTERTOP 36 rec 914 HEIGHT __ 33 min 838 CABINET WIDTH Dimensions in parentheses are in millimeters unless otherwise specified The drawer microwave can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach Power cord access hole in cabinet should be a minimum 11 2 38 diameter hole and deburred of all sharp edges IMPORTANT NOTE Always allow sufficient power cord length to the electrical outlet to prevent tension Always check electrical codes for requirements The drawer microwave can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach Power cord access hole in cabinet should be a minimum 11 2 38 diameter hole and deburred of all sharp edges IMPORTANT NOTE Always allow sufficient power cord length to the electrical outlet to prevent tension Always2. 11 143 4 375 1515 16 TOP CLEAT OPENING 405 lt 221 8 562 gt HEIGHT FLUSH INSET OPENING WIDTH HEIGHT L 1 025 SIDE CLEATS 36 914 16 17 PLATFORM 25 min 635 STANDARD 243 8 619 CABINET DEPTH FLOOR TO FLUSH INSET WIDTH COUNTERTOP lt 27 rec 686 HEIGHT L 24 min 610 CABINET WIDTH INSTALLATION INSTRUCTIONS 30 762 DRAWER MICROWAVE OVERALL DIMENSIONS lt 281 8 714 11 4 2 CORD 411 16 S 32 499 CHANNEL gt lt 119 z a 157 16 149 16 392 370 297 8 759 233 8 594 BEHIND FRAME 297 8 759 INSTALLATION SPECIFICATIONS Standard Installation 33 rec 838 31 2 89 x 2 51 30 min 762 ANTI TIP BLOCK CABINET WIDTH S 4 143 4 375 2 51 OPENING ALLOW FOR HEIGHT 36 914 UP TO 3 4 19 STANDARD OVERLAP FLOOR TO ON ALL SIDES COUNTERTOP lt 231 2 min 597 gt HEIGHT 287 16 722 gt OPENING DEPTH OPENING WIDTH lt 24 min 610 gt CABINET DEPTH VIEW Flush
3. DRAWER MICROWAVE INSTALLATION INSTRUCTIONS WOLF WOLF CONTACT INFORMATION Wolf Customer Service 800 332 9513 Website wolfappliance com WOLF is a registered trademark of Wolf Appliance Inc As you follow these instructions you will notice WARNING and CAUTION symbols This blocked information is important for the safe and efficient installation of Wolf equip ment There are two types of potential hazards that may occur during installation CAUTION signals a situation where minor injury or product damage may occur if you do not follow instructions A WARNING states a hazard that may cause serious injury or death if precautions are not followed Another footnote we would like to identify is IMPORTANT NOTE This highlights informa tion that is especially relevant to a problem free installation WOLF DRAWER MICROWAVE INSTALLATION REQUIREMENTS IMPORTANT NOTE This installation must be completed by a qualified installer or Wolf authorized service center technician Save this installation manual for local electrical inspec tor s use Read and save these instructions for future reference INSTALLER Read all of the Installation Instructions before installing the drawer microwave Remove all packing material before connecting the electrical supply Observe all governing codes and ordi nances sure to leave these instructions with the consumer CONSUMER Keep this manu
4. LFAPPLIANCE COM AIAN IE 813533 TINSEB509MRRO 10 2008
5. al with your Use amp Care Guide for future reference As when using any microwave oven gener ating heat there are certain safety precau tions you should follow These are listed in the Use amp Care Guide Read all and follow carefully sure your drawer microwave is installed and grounded properly by a qualified installer or service technician Rating plate location Any questions or problems regarding the installation should be directed to your dealer or Wolf Appliance Inc at 800 332 9513 You can also visit our website wolfappliance com CLEARANCES AND DIMENSIONS A WARNING For safety considerations do not install drawer in any combustible cabinetry which is not in accord with the stated clearances and dimensions on pages 6 7 RATING PLATE LOCATION Record the model and serial numbers before installing the drawer microwave Both numbers are listed on the product rating plate Refer to the illustration below The rating plate includes model and serial number Open the drawer fully The label is slightly beyond the back wall of the microwave cavity facing up from the flat surface Rating plate Open the drawer fully The label is slightly beyond the back wall of the microwave cavity facing up from the flat surface RATING PLATE INFORMATION Model Number Serial Number WOLF DRAWER MICROWAVE IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING If the information in th
6. ational Electrical Code regulations In addition be aware of local codes and ordinances when installing your service IMPORTANT NOTE You must follow all National Electrical Code regulations In addition be aware of local codes and ordinances when installing your service WOLF DRAWER MICROWAVE ELECTRICAL REQUIREMENTS GROUNDING INSTRUCTIONS This appliance must be grounded The drawer microwave is equipped with a cord having a grounding wire with a grounding plug It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances In the event of an elec trical short circuit grounding reduces risk of electric shock by providing an escape wire for the electric current WARNING Improper use of the grounding plug can result in a risk of electric shock Do not use an extension cord If the power supply cord is too short have a qualified electrician or serviceman install an outlet near the appliance DRAWER INSTALLATION 1 Place the drawer adjacent to the wall or cabinet opening Plug the power supply cord into the electrical outlet 2 Carefully guide the drawer into the prepared opening Avoid pinching the cord between the oven and the wall 3 Slide the drawer all the way until the mounting flange is flush with the face of the cabinet See illustration below 4 Open the drawer Using the 4 holes on the dr
7. awer as a template pre drill the cabinet using a 1 16 1 6 bit See illustration below 5 Secure the drawer with the 4 screws supplied See illustration below 3 Prong Plug 3 Prong Receptacle Ground Receptacle Box 4 screws provided Grounding 10 Drawer installation Dimensions in parentheses are in millimeters unless otherwise specified INSTALLATION INSTRUCTIONS IF YOU NEED SERVICE Maintain the quality built into your drawer microwave by calling a Wolf authorized service center To obtain the name and number of a Wolf authorized service center check the Contact amp Support section of our website wolfappliance com or call Wolf Customer Service at 800 332 9513 When calling for service you will need the model and serial numbers of the drawer microwave Both numbers are listed on the product rating plate Refer to the illustration on page 3 CONTACT INFORMATION Wolf Customer Service 800 332 9513 Website wolfappliance com The information and images in this book are the copyright property of Wolf Appliance Inc an affiliate of Sub Zero Inc Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance Inc an affiliate of Sub Zero Inc Wolf Appliance Inc all rights reserved 11 WOLF APPLIANCE INC P O BOX 44848 MADISON WI 53744 800 332 9513 WO
8. check electrical codes for requirements WOLF DRAWER MICROWAVE 30 762 DRAWER MICROWAVE INSTALLATION SPECIFICATIONS Installation below a Wolf E Series Built In Oven SIDE VIEW 25 min 635 CABINET DEPTH ee O 273 16 281 2 min 691 724 OPENING FLUSH HEIGHT INSET HEIGHT SSS 143 4 375 1515 16 OPENING 405 HEIGHT FLUSH INSET HEIGHT m 2000 K d TOP VIEW 11 4 32 243 4 min FOR DRAWER 629 MICROWAVE FLUSH 1 25 FOR ead E SERIES OVEN SIDE CLEATS 36 rec 914 33 min 838 CABINET WIDTH 7 8 22 TOP CLEAT 281 2 724 E SERIES OVEN OPENING WIDTH 5 16 8 PLATFORM 281 2 724 E DRAWER MICROWAVE OPENING WIDTH 11 16 17 PLATFORM 19 483 TO FLOOR typical H 303 8 min 772 FLUSH INSET WIDTH 1 25 SIDE CLEATS 1 25 SIDE CLEATS NOTE Refer to the 30 762 E Series built in oven specifications for electrical location Platform must be able to support 250 Ibs 113 kg INSTALLATION INSTRUCTIONS ANTI TIP BLOCK INSTALL ANTI TIP BLOCKING To reduce the risk of tipping of the drawer the Anti Tip block must be properly installed located 1413 16 376 above the floor on which the d
9. is manual is not followed exactly a fire or electrical shock may result that could cause property damage personal injury or death To reduce the risk of tipping the drawer microwave must be secured by a properly installed Anti Tip block This drawer microwave must be electri cally grounded in accordance with local codes Make sure the wall coverings and the cabinets around the drawer microwave can withstand the heat generated by the drawer microwave Never leave children alone or unattended in the area where a drawer microwave is in use Never leave the drawer open when the microwave is unattended Stepping leaning or sitting on the drawer may result in serious injuries and can also cause damage to the drawer microwave Do not use the drawer microwave as a storage space This creates a potentially hazardous situation Check that the time of day is in the display If not touch Stop Clear to prevent unintended use INSTALLATION INSTRUCTIONS UNPACKING YOUR MICROWAVE Remove all packing materials from inside the drawer microwave Do not remove the waveguide cover which is located on the top of the drawer microwave Remove the feature sticker if there is one Check the drawer for any damage such as misaligned or bent drawer damaged drawer seals and sealing surfaces broken or loose drawer guides and dents inside the cavity or on the front side of the drawer If there is any damage do not operate the drawe
10. r microwave and contact your dealer or a Wolf authorized service center Refer to the illustrations below CLEARANCES AND DIMENSIONS Dimensions shown on the following pages must be used Given dimensions provide minimum clearance Locate electrical outlet in the shaded area in the upper left hand corner of the cutout See page 8 Contact surface must be solid and level Pay special attention to the floor on which the drawer microwave will sit The floor of the opening should be constructed of plywood strong enough to support the weight of the oven about 100 pounds 45 kg Check location where the drawer microwave will be installed for proper elec trical supply a Your oven can be built into a cabinet or wall by itself or under a gas or electric wall oven Be sure that the clearance of the floor between the wall oven and the drawer microwave is a minimum of 2 51 a The microwave interior will easily accom modate a 9 229 x 13 330 oblong dish or a bag of microwave popcorn Sealing surface Waveguide Sealing surface lt gt Oven Waveguide cover location Sealing surface location Dimensions in parentheses are in millimeters unless otherwise specified The drawer microwave can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach Power cord access hole in cabine
11. rawer microwave will sit The 6 152 Anti Tip block must be provided by the installer See pages 6 7 The Anti Tip block prevents serious injury that might result from spilled hot liquids If the drawer microwave is ever moved to a different location the Anti Tip block must also be moved and installed When installed to the wall make sure that the screws completely penetrate the dry wall and are secured in wood or metal so that the block is totally stable When fastening be sure that the screws do not penetrate electrical wiring or plumbing ELECTRICAL REQUIREMENTS ELECTRICAL OUTLET LOCATION The electrical requirements are a 120 volt 60 Hz AC only 15 amp or more protected electri cal supply It is recommended that a separate circuit serving only this appliance be provided The drawer is equipped with a 3 prong grounding plug It must be plugged into a wall receptacle that is properly installed and grounded Should you only have a 2 prong outlet have a qualified electrician install a correct wall receptacle NOTE If you have any questions about the grounding or electrical instructions consult a qualified electrician or service person Anti tip Electrical Outlet Location Anti tip block Dimensions in parentheses are in millimeters unless otherwise specified Electrical Outlet IMPORTANT NOTE You must follow all N
12. t should be a minimum 11 2 38 diameter hole and deburred of all sharp edges IMPORTANT NOTE Always allow sufficient power cord length to the electrical outlet to prevent tension Always check electrical codes for requirements WOLF DRAWER MICROWAVE 24 610 DRAWER MICROWAVE OVERALL DIMENSIONS lt 219 16 548 gt A POWER 11 4 13 4 CORD 411 16 lt 32 y we CHANNEL gt lt 119 MT DI 233 8 594 157 16 149 16 392 370 Y f o 237 8 606 233 8 594 gt ibi BEHIND FRAME 161 2 419 Y 237 8 606 INSTALLATION SPECIFICATIONS Standard Installation I lt 27 rec 686 gt 31 2 89 x 2 51 24 min 610 ANTI TIP BLOCK CABINET WIDTH 143 4 375 2 51 OPENING ALLOW FOR HEIGHT 36 914 UP TO 3 4 19 STANDARD OVERLAP FLOOR TO ON ALL SIDES COUNTERTOP lt 231 2 min 597 HEIGHT 221 8 562 gt OPENING DEPTH OPENING WIDTH 24 min 610 CABINET DEPTH VIEW Flush Inset Installation 243 4 min 629 FLUSH INSET 11 4 DEPTH 32 J H SIDE CLEATS 31 2 89 x 2 51 ANTI TIP BLOCK 19 16 38 DS zc E 7 16
Download Pdf Manuals
Related Search