Sub-Zero 601F User's Manual
Contents
1. rough opening HARDWARE CONSIDERATIONS Overlay models come without handle hardware The beauty of this design is that you can match the surround ing cabinet hardware You or the cabinet manufacturer must provide handle hardware to match the overall deco rating scheme The handle hardware must be installed before installing the panel assembly Use larger D style handles If screws with thick heads are used the screws will need to be countersunk into the door before the panel is put into place Refer to the full scale illustrations on pages 11 12 for handle hardware considerations IMPORTANT NOTE Sub Zero does not recommend using single pull knobs on any of its Built In models Optional stainless steel handles are available in a variety of diameters and lengths in the classic platinum and carbon stainless steel finishes and polished chrome Contact your Sub Zero dealer for specifics To obtain local dealer information visit the Locator section of our website subzero com 10 SUB ZERO Planning Information Built In Model 601F HANDLE PROFILE FRAMED APPLICATION v OPTIONAL EXTENDED FULL LENGTH HANDLE wn BUILT IN 3 76 11 4 32 PANEL STANDARD FULL LENGTH 1 25 PANEL HANDLE 3 4 19 PANEL 1 2 13 PANEL 1 4 6 FRAMED PANEL 1 4 6 PANEL FULL SCALE TEMPLATES The following full scale illustratio2. Design 601F F Overlay Design 601F O Classic Stainless Steel 601F S Platinum Stainless Steel 601F P Carbon Stainless Steel 601F B You must allow 90 days from order to delivery for platinum and carbon finishes ACCESSORIES Front panels for framed design in white almond and classic stainless steel Side panels in white almond and classic stainless steel Extended framed handle Stainless steel and polished chrome handles for overlay design 90 and 105 door stop kits Accessories are available through your Sub Zero dealer To obtain local dealer information visit the Locator section of our website subzero com Dimensions in parentheses are in millimeters unless otherwise specified SPECIFICATIONS v Model 601F All Freezer Overall Width 36 914 Overall Height 73 1854 Overall Depth 24 610 Freezer Capacity 19 3 cu ft 547 L Minimum Height levelers in 723 4 1848 Door Swing Clearance 361 16 916 Electrical Requirements 115 V AC 60 Hz 15 amp circuit Plumbing Requirements 1 4 copper line Water Supply 20 100 psi Annual Energy Usage 737 kWh 67 based on 9 06 cents per kilowatt hour Shipping Weight Framed 378 Ibs 171 kg Overlay 378 lbs 171 kg Stainless Steel 406 Ibs 184 kg Specifications are subject to change without notice SUB ZERO Planning Information Built In Model 601F INSTALLATION SPECIFICATIONS BUILT IN SHUT OFF VALVE TOP VI
3. EW EXTEND WATER LINE APPROX 36 914 FROM BACK WALL 723 4 1848 ROUGH OPENING HEIGHT 902 ROUGH OPENING WIDTH LOCATE ELECTRICAL 351 2 WITHIN ENTIRE SHADED AREA LOCATE WATER SUPPLY WITHIN BOTTOM SHADED AREA ONLY 24 610 DIMENSIONS e 152 3 FRONT VIEW v Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical Location of Water Supply 35 1 2 902 723 4 1848 24 610 Within entire shaded area Within lower shaded area See Installation Instructions shipped with unit for detailed specifications Refer to the Sub Zero Design Guide pdf file for additional specifications Dimensions in parentheses are in millimeters unless otherwise specified SUB ZERO Planning Information Built In Model 601F INSTALLATION NOTES Refer to the illustrations and specifications for overall dimensions finished rough opening dimensions and installation specifics Allow the door to open a minimum of 90 or you ll have problems removing drawers With the door opening at 90 you may have to move drawers slightly to clear the door interior Refer to the minimum door swing clearance in the specifications chart For corner installations allow for a minimum 3 76 filler so that the door can open to 90 If you re u
4. SUB ZERO Planning Information Built In Model 601F All Freezer Lighted electronic control panel Adjustable wire BUILT IN shelves Model 601F F Framed Automatic ice maker Pull out ice container Roll out storage Model 601F O PASKAI Overlay Hermetically sealed refrigeration units Model 601F S P B Stainless Steel The Sub Zero Model 601F all freezer is available in your choice of the framed overlay or stainless steel design application Three stainless steel finishes are offered classic S platinum P and carbon B Dimensions in parentheses are in millimeters unless otherwise specified 11 06 Serial and model number plate Adjustable door E shelves Four sided magnetic gaskets SS Door closers Front venting allows unit to be completely built in Removable kickplate Stainless steel design shown With the installation of a harness kit these appliances are Star K compliant to meet strict religious regulations in conjunction with specific instructions found on star k org You may purchase this harness kit through your Sub Zero dealer To obtain local dealer information visit the Locator section of our website subzero com Sines with the Model 601R or 601RG this popular all freezer model strikes a handsome pose This combination is formidable
5. and no one else in the market can boast the performance these two offer The automatic ice maker has a large storage drawer for easy access to the crescent shaped ice SUB ZERO Planning Information Built In Model 601F FEATURES gt 36 914 wide all freezer Automatic ice maker provides an ample supply of crescent shaped ice Sub Zero s refrigeration system ensures the PPM P best storage and energy efficiency Front venting allows unit to be completely A A built in and serviced from the front Shallow depth design means access is easy to any area of the freezer Meets strict Department of Energy require are ments Electronic digital controls are up front and easy to use UL approved for US and Canada Bright interior lighting Two five and twelve year residential warranty exclusions apply warranty information can be found on our website Door alarm will let you know with an audible subzero com beeping if your freezer door is left ajar Adjustable wire shelves OVERALL DIMENSIONS v 237 8 3 8 10 606 FRAME BEHIND lt EXTENSION FRAME 73 1854 361 16 916 Y AR pos Me 914 610 914 Stainless steel design shown Dimensions may vary by x a 3 Dimensions in parentheses are in millimeters unless otherwise specified 2 SUB ZERO Planning Information Built In Model 601F BUILT IN MODEL OPTIONS v Framed
6. e between the supply and the unit Dimensions in parentheses are in millimeters unless otherwise specified Do not use self piercing valves A saddle valve kit 4200880 is available from your Sub Zero dealer To obtain local dealer informa tion visit the Locator section of our website subzero com gt A line filter is required when water condi tions have a high sediment content The ice maker operates on water pressure of 20 psi 1 4 bar to 100 psi 6 9 bar In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently gt The water line should be routed up through the floor within 1 2 13 from the back wall and no higher than 3 76 off the floor If you have to come through the wall make sure the water line is no more than 3 76 from the floor Locate water supply within the lower shaded area shown in the installation illustration Regardless of the routing allow 3 9 m of excess copper tubing to remain outside the wall or floor for easy connection to the unit A115 volt 60 Hz 15 amp electrical supply is required The supply circuit for this appliance must be protected by a 15 amp fuse or circuit breaker It is recommended that a separate circuit serving only this appliance be provided gt All Built In models are equipped with a 6 1 8 m power supply cord with a 3 prong grounding plug which must be plugged into a mating 3 prong
7. grounding type wall receptacle Locate electrical within the shaded area shown in the installation illustration You must follow all National Electrical Code regulations In addition be aware of local codes and ordinances when installing your service To prevent the unit from tipping forward and provide a stable installation the unit must be secured in place with an anti tip blocking kit If there is a solid soffit above the unit with clear ance between the unit and the soffit of 1 25 or less you won t need to block the unit gt For installations with clearances of more than 1 25 you must block the unit with the anti tip blocking kit wood block and hardware provided with each Built In unit Refer to the Built In Installation Instructions packed with the appliance which provides step by step procedures for making sure the unit is installed properly SUB ZERO Planning Information Built In Model 601F BuiLT IN Dimensions in parentheses are in millimeters unless otherwise specified ADDING PANELS In your plan for panels be sure you are working with the Sub Zero panel design family called for in your design If you have chosen the stainless steel design the unit will be shipped complete with wrapped stainless steel doors and handle hardware You will not have to install front door panels If you and your client have ordered a framed or overlay design model you will be adding panels to give the
8. h handle Optional extended full length handles that provide additional finger clearance for raised panels are available through your Sub Zero dealer To obtain local dealer information visit the Locator section of our website subzero com To install framed panels refer to the installation instruc tions shipped with each unit These instructions can also be found on our website subzero com FRAMED PANEL DIMENSIONS v WIDTH HEIGHT Door Panel 341 8 867 5815 16 1497 Handle Recess Location A 2915 32 749 Maximum Panel Weight 50 Ibs 23 kg 7 SUB ZERO Planning Information Built In Model 601F BuiLT IN OVERLAY PANELS V Spacer Panel Overlay Panel 1 4 6 Backer Panel H 5 16 8 min e E Su H 5 32 4 Door Drawer i 146 2 Grille Trim Three panel assembly cross section Overlay Panel ig ad Spacer Panel he Panel Three panel assembly rear view Dimensions in parentheses are in millimeters unless otherwise specified OVERLAY PANELS The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room To achieve this look the most common way is to work with three panels the decorative overlay panel a 10 3 spacer panel and a 1 4 6 backer panel Depending on your cabinet manufacturer this could be one panel routed for different dimensions or more likel
9. ise specified 13 Planning Information SUB ZERO Built In Model 601F 90 DOOR OPENING OVERLAY PANEL APPLICATION BUILT IN SUB ZERO UNIT DOOR CLOSED e dme xu aN i op gt 6a ZO Zr SE 6a MAIN FRAME 237 8 606 TO REAR OF SUB ZERO 90 DOOR OPENING TOP VIEW DOOR OPEN 90 See oe see a a ae oe eee ae ae TAN 9 v f I penes ae Ga rer Vale ck TAN L 2 L 4 L J 1 L i L TaNvd 60 t g 4 F d t E 4 r TAIN SZ 4b a ce a a el ee ae La al L 4 L J 1 L 4 L TaNvd Z8 b b i a pa I E l l l l dz Lk olcb od 3e x o3 26 amp I I I gt x j 1 l l l I l 1 x9 i I j I j I oct on ae ae ee ee US E e 2 o 2 o Soe E O o Tom Q SOROR OX DH x X 7 e e T N N N e e Approximate thickness of wrapped stainless steel door Dimensions in parentheses are in 14 millimeters unless otherwise specified
10. n parentheses are in millimeters unless otherwise specified OVERLAY PANELS OVERLAY PANEL DIMENSIONS v WIDTH HEIGHT Door Panel 347 16 875 591 4 1505 Door Spacer 33 1 2 851 585 16 1481 Door Backer 341 8 867 5815 16 1497 Maximum Weight panel assembly 50 Ibs 23 kg SUB ZERO Planning Information Built In Model 601F BuiLT IN SIDE PANELS v 237 8 606 gt BEHIND FRAME 4 102 i 3 76 Cut outs for grille and toe kick area Dimensions in parentheses are in millimeters unless otherwise specified SIDE PANELS Side panels can be used with the framed overlay and stainless steel design applications When planning for side panels with the installation of the Built In model you need to be aware of space configuration to achieve a pleasing fit Depending on the exact panel you are using with your unit the height of the panel will vary Cut outs around the toe kick and grille area are required if a 1 4 6 thick panel will be inserted into the main frame channel The panel will need to be 24 610 deep Refer to the illustration on this page for placement of toe kick and grille area cut outs If a 3 8 10 thick panel is used the panel will abut the main frame and should be 237 8 606 deep The toe kick area may or may not be cut out depending on the look you want to achieve IMPORTANT NOTE The use of side panels may change the width of your
11. ns enable you to understand some of the unique situations you may face as you design the Built In units into homes These templates can be easily photocopied or used in your tracings Dimensions in parentheses are in millimeters unless otherwise specified HANDLE PROFILE The full scale illustration above shows handle placement for the framed application standard full length handle and the optional extended full length handle shown in the dashed line 11 SUB ZERO Planning Information Built In Model 601F HANDLE PROFILE STAINLESS STEEL OVERLAY APPLICATIONS STANDARD STAINLESS STEEL HANDLE 2 BUILT IN 11 4 32 PANEL 1 25 PANEL 3 4 19 PANEL 5 8 16 PANEL 1 2 13 PANEL 1 4 6 PANEL NOTE FOR OVERLAY APPLICATIONS OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 5 8 16 THICK PANEL AND HANDLE PROFILE The full scale illustration above shows handle placement for the standard stainless steel handle on the wrapped stainless steel door and on overlay panel applications shown in the dashed line Dimensions in parentheses are in millimeters unless otherwise specified IMPORTANT NOTE For overlay applications the optional stainless steel handle must be mounted on a panel at least 5 8 16 thick For overlay applications mount door handles close to the opening edge of the do
12. or for ease of opening 12 SUB ZERO Planning Information Built In Model 601F PANEL AND HANDLE PROFILE 130 DOOR OPENING v 130 DOOR OPENING WITH 2 51 FILLER STRIP TOP VIEW SUB ZERO UNIT FILLER STRIP 2 51 ALLOW FOR FILLER LAP BEHIND FLANGE DOOR CLOSED OVERLAY PANEL 3 4 19 THICK oo 4 eee ow 5 NOMINAL rd pA 7 rd o APPROX i ff PROFILEOF D y STAINLEss off y STEELDOOR STANDARD f fF AND HANDLE FRAMED fete o FULL LENGTH Da AM C HANDLE V FRE D 3 y PN I lt 7 3j Ve SS FA rd T po DOOR OPEN 130 XN b Nenu ue RT d Z 4 OPTIONAL 7 FRAMED EXTENDED rd FULL LENGTH HANDLE 7 d 7 7 7 rd 7 Pd 7 The full scale illustration above shows the panel To obtain local dealer information visit the and handle profile of a 130 door opening with Locator section of our website subzero com 2 Sol tiller stip for framed applications The full scale illustration on the following page Interference of door panels with handles at lets you see what considerations you need to maximum door swing may require the use of an make for any overlay panel applications and optional 90 door stop available through your how they may interact with adjacent cabinets Sub Zero dealer and or countertops Approximate thickness of wrapped stainless steel door Dimensions in parentheses are in millimeters unless otherw
13. sing raised panels consider using a wider filler A 90 door stop is available as an accessory When units are installed side by side a filler strip is recommended The width of this filler strip will vary depending on the configuration and panels you use An anchoring kit may also be used to attach two units together This kit is available through your Sub Zero dealer Be sure to add the filler strip width to your finished rough opening dimension In any side by side installation without a filler strip add an additional 1 2 13 to your combined numbers This will allow for the proper width Refer to the full scale illustrations at the end of this section for specifics on door openings and filler size alternatives gt If your client has chosen the stainless steel design the unit will be shipped complete with wrapped stainless steel doors and handle hardware You will not have to install front panels gt If your client has chosen the framed or overlay design you will be adding front panels to give the unit the custom Sub Zero look The overlay design also allows you to add your own handles or you may choose accessory handles available through your Sub Zero dealer Refer to pages 6 10 for detailed information on adding panels For Built In models with an automatic ice maker rough in the water supply line Connect a 1 4 OD copper line to the house supply being sure to use an easily accessible shut off valv
14. unit the custom Sub Zero look Specifications on the following pages provide installation considerations for framed and overlay door panels Side panels can be used with the framed overlay and stainless steel design applications Refer to specifications on page 10 SUB ZERO Planning Information Built In Model 601F BuiLT IN FRAMED PANELS v PANELS 1 4 6 THICK OR LESS Y Trim reveal 1 4 6 min 1 4 6 Panel Framed door panel 4 6 thick or less PANELS THICKER THAN 1 4 6 Y Trim reveal 1 4 6 min Rout to 1 4 6 thickness Framed door panel thicker than 1 4 6 Framed Door Panel Dimensions in parentheses are in millimeters unless otherwise specified FRAMED PANELS If the thickness of the custom panels is less than 1 4 6 they must be backed up with a sheet of shim material to build the total thickness to 1 4 6 If the panel is thicker than 1 4 6 an edge must be routed around the panel to ensure a proper fit Refer to the illustrations on this page IMPORTANT NOTE Routing recessing or optional extended handles may be required on raised panels for finger clearance under the handle Refer to the full scale illustrations on pages 11 14 IMPORTANT NOTE The weight of each panel cannot exceed 50 Ibs 23 kg The traditional framed models come with an 11 279 louvered grille and elegant full lengt
15. y three different panels Regardless of the physical construction of the panels routing or three panel assembly you will need to follow the exact dimensions and panel placement to ensure a proper fit The top illustration on this page is a cross section view of the three panel assembly showing placement of the door drawer grille trim The bottom illustration shows a rear view of the three panel assembly and critical dimen sions standard for all overlay models Overlay models will come with no handle hardware because the beauty of this design is that you can match the surrounding cabinetry hardware For overlay door panel dimensions refer to specifications on page 9 IMPORTANT NOTE Keep in mind that the Sub Zero door panels have the potential for hitting adjacent cabinets and or countertops when they are opened You need to be aware of your surrounding cabinetry and space limitations when using the overlay models Refer to the full scale illustrations on pages 13 14 IMPORTANT NOTE The weight of each door panel assembly cannot exceed 50 Ibs 23 kg The total thick ness of all panels for an overlay model must be at least 5 3 16 thick To install overlay panels refer to the installation instruc tions shipped with each unit These instructions can also be found on our website subzero com SUB ZERO Planning Information Built In Model 601F BuiLT IN Ww Overlay Door Panel Dimensions i
Download Pdf Manuals
Related Search