Star Micronics NP-415W User's Manual
Contents
1. D F0301 Specifications for Kiosk module printer NP 215 NP 225 NP 325 NP 415W Revision 1 00 2000 08 01 1 edition Revision 2 00 2001 04 18 2 edition Revision 2 10 2001 06 13 3 edition Revision 2 20 2002 01 29 4 edition Revision 2 30 2002 02 15 5 edition Revision 2 40 2002 03 26 6 edition Revision 2 50 2002 04 12 7 edition Revision 2 60 2002 07 09 8 edition Revision 2 70 2003 01 31 9 edition Notice All features and specifications described are subject to change without notice Read carefully Before Using the Printer Wrong handling of the printer may cause its performance declined and the product damaged Please read the notes below before handling 1 10 11 12 13 Static discharge prevention must be made for installation and removal of the printer to protect IC and other electrical parts Connect it to the earth ground It is also requested to remove the static from body of the person before handling especially the input terminal Avoid excessive force to the input terminal for handling When any type of paper other than specified in this manual is used it may cause deterioration of the print quality and thermal head reliability Examples of troubles 1 Print quality deterioration by using low sensitivity paper 2 Thermal head wears due to roughness of paper surface 3 Sticking between heat receipt layer and thermal head and vibratio2. osese 16 2 Start and end of self diagnostic print Set the power on while pressing the FEED switch and release the FEED switch after the printer mechanism activates to start self printing The self diagnostic print automatically ends when a preset number of characters are finished printing While printing the printer is in Off line mode 4 1 4 No paper sensor No paper sensor is mounted on the paper path in the printer mechanism It detects no paper status of the roll paper When detecting no paper status the printer sends PE signal to the host and stop printing Pay special attention to the end of roll paper The end should not be glued to the core of the roll If no paper status is detected replace the roll paper 4 2 Processing error 1 Error detection details Name Status BUSY PE PE Removal status status Comm error 232C Comm error Align comm Parity condition Overrun Flaming Data print Paper near Paper remain sense L H H Obit1 Load paper end CN7 sensor Head up Head up L L L 1bit 1 On Head up lever down Paper end No paper L H L 2bit 1 On Load paper Head temp Over 80 L L L 3bit 1 Flash Return normal high with 60 C Cutter error Cutter jam Remove jam and POWER OFF INIT When the above errors are detected except transmission error and paper low end error printer stops all operations and outputs error signal In the case of parallel interfa
3. 43 QR code print lt lt ESC M gt gt ESC 0 5 DATA DATA 1 NUL CODE lt 1B gt h lt 71 gt h S E DATA lt 2C gt h DATA lt 00 gt About parameter 1 5 module size Assign 1 module size of QR code by printer s dot numbers There are 5 sizes which can be assigned 1 2 3 4 8 dots If invalid size is assigned the printer assigns it as 4 dots 2 Correction level Selects error correction level to be used for restoring QR symbol Following values can be assigned If invalid value is assigned the printer determines it to be L E Correction level Restore capability 0 L 7 1 15 2 Q 25 3 M 30 3 Input data mode Assign input data mode Following modes can be assigned If invalid mode is assigned data is ignored until valid Mode is assigned M Input data mode N Numeric mode A Alpha numeric mode 8 bit byte mode Kanji mode If multiple modes should be input each mode data M data needs to be separated by If you want to input and NULL in the data of 8 bit byte mode input lt 21 gt h and 1 21 h NULL itself is input as Kanji data should be input by Shift JIS code Restrictions Available QR codes are from version 1 to version 14 of model 1 symbols If input
4. transmitted to odes below 1F h is nteed if the blank control code c ot be 6 2 Overseas code table International character set U S A SEPT EREEREER en nen mmm e ifa fafa 2 fe fee fe fr fe Jae Mir irr 3 belja o fall ape fo fa e fools etd Epp Hepi Printer operation cannot be guaranteed if the blank control code codes below 1F h is transmitted to 6 3 International character code table M Character set 23 24 40 5B 56 50 5E 60 7B 7C 7D JE Fu U S A I France dii eie wig o un o Germany U K Denmark1 Q e m H o Sweden Italy aU Spain Japan Norway Denmark2 41 7 Cable 7 1 B501 power cable No PARTS NAME IY MATERIAL TREATMENT 1 Mating connector 1 XHP 4 JST 2 Terminal 4 SXH 001T PO0 6 JST 3 High temp Vinyl cable Red 2 UL1007 AWG 22 No 12 4 High temp Vinyl cable Black 2 UL1007 AWG 22 No 3 4 42
5. 1 Drop in type of paper holder is for NP 225 NP 325 and NP 415W NP 215 is paper holder type 1 3 Configuration The printer consists of the following components Product Name Description Specification PartNo Qty 215 1 X Printer Nee 1 325 1 X NP 415W 1 X 60x 48mm 24 X117 1 X X Thermal paper 80x 48mm 24 X121 1 X 112x 48mm 24 X116 1 X 80R 35 029Q 1 X dic 80L 35 0300 1 X Screws tight 21 U196 2 X B501power D P44507 30 439A 1 X X X X cable B501 power cable D type only 2 Specifications 2 1 Basic specifications No Specifications NP 215 225 NP 325 NP 415W 1 Printspecs 1 Print method Line thermal dot lt lt 2 Total dots line 432 dots 576 dots 832 dots 3 Dot density 8 dots lt lt 4 Print width 54 72 104 mm 5 Print speed Max 85 mm s 70mm s 70mm s It can be changed by the 1 partition drive 1 partition drive Automatic partition condition ASCII print ASCII print drive ASCII 38 print 2 Character specs 6 Print digits Font A 12x 24 Font B 9x 17 7 Line feed pitch 1 Character size Font A 12x 24 Font B 9x 17 2 Character types ASCII Block graphics International 3 Character modification 36 digits Font A 48 digits Font B 0 125 mm 1 50x 3 00 mm 1 13x 2 13 mm 224 80x2 32 Double width 48 digits Font A 64 digits Font B lt 69 digits Font 92 digit
6. approx 2 5m 1m When inner of paper core is 12 and outer is 18 Reflection sensor approx 1 250g Approx 3m 1 5m When inner of paper core is 12 and outer is 18 Changeable reflection sensor 2 2 Printing area and cutter position Cutter position Cutting place A gt 0 0mm Cutter position 3 0mm Head position 17 5mm Sensor position 28 5mm NP 215 225 325 NP 415W 60mm 80mm 112mm 3mm 4mm 4mm 54mm 72mm 104mm gt 432dot 576dot 832dot 1 Black mark printing is used when preprint paper is formatted and used 2 Black mark printing is printed on the backside with black ink 3 Do not print around the black mark printing area with dark ink Black mark printing 2 3 Power supply specifications 1 Power voltage DC24V 5 2 Current consumption 2 3 NP 215 225 NP 325 NP415W 1 partition 2 partition 1 partition 2 partition 1 partition 2 partition Standby Approx 0 1A ASCII printing Approx Approx Approx Approx Approx Printing average of 16 14A i 09A 1 7 __ 11A i 13A Bit image printing Approx Approx Approx Approx Approx Max 10096 6 0 32 7 8A 41 5 7A 2 A sufficient volume of power supply is required to maintain print quality due to high peak current that may run according to printing 3 If power supply cable is excessively
7. frane ground 5 D type This drawing is for NP 215P 2 NP 225 dimensional drawing screw hol es to fi x frane ground frane gr ound 107 65 710 49 4 This drawing is for NP 225P 3 325 dimensional drawing M8 screw hol es to fi x frane ground 00 0000 frane grounds This drawing is for NP 325P frane ground 4 NP 415W dimensional drawing SZ 0 183 7 paper exit 00 0000000 This drawing is for NP 415WP 3 Interface specifications 3 1 Parallel interface Centronics 1 Data input 2 Control signals 3 Input signal to a printer DATA 0 7 STB NNIT ILF 4 Output signal from a printer 8 bit parallel method DATA 0 DATA 7 JACK BUSY STB ERROR PE SLCT INIT 8 bit parallel signal positive logic Signal to read 8 bit data negative logic Signal to reset an entire printer negative logic Signal to feed paper to print mechanism negative logic Enquiry signal for 8 bit data It s also pulse signal which is output after BUSY signals negative logic BUSY positive logic ERROR Indicate BUSY status of the printer Inputs new data at
8. 1 3V 12V Space Logic 0 3V 12V 5 Receive data RD signal RS 232C Mark 1 Space 0 6 Reception control DTR signal RS 232C Mark 1 Space 0 7 Transmission control TD signal DC1 11 h XON Enable data receiving DC3 13 h XOFF Disable data receiving 11 3 3 Connector connections 1 J1 Power input 2 CN2 Connect to printer mechanism head 3 CN3 Connect to printer mechanism motor CN4 Connect to printer mechanism sensors CN5 Data signal input 6 CN6 Connect to autocutter CN7 Connect to auxiliary sensor paper low end 8 CN8 Connect to operation panel 9 CN9 Connect to presenter NPT 301 only 3 4 Connector signal details 1 J1 power input connecter D type Printer side connector B4B XHA JST Mating connector XHP 4 JST Pin Signal name Input Output Function 1 VH Input Power DC 24V 2 VH Input Power DC 24V 3 GND Power GND 4 GND Power GND A sufficient volume of power supply is required to maintain print quality due to high peak current that may run according to printing If power supply cable is excessively long the operation may become unstable Cable should be as short as possible If not available connect cables near the printer and place an electrolysis condenser of 2200 between power supply and ground Voltage resistance should be higher than 35V Make sure to connect FG wire to prevent from ESD problems 2 Power input connec
9. This printer does not support any operations caused by the commands or control commands not specified in this manual Table of Contents Overview 1 1 Overview 1 2 Features 1 3 Configuration Specifications 2 1 Basic specifications 2 2 Printing area and cutter position 2 3 Power supply specifications 2 4 Reliability 2 5 Dimensions 1 NP 215 dimensional drawing 2 NP 225 dimensional drawing 3 NP 325 dimensional drawing 4 NP 415W dimensional drawing Interface specifications 3 1 Parallel interface Centronics 3 2 Serial interface RS 232C 3 3 Connector connections 3 4 Connector signal details Functions 4 1 Function setting 4 2 Processing error 4 3 Buffer full print 4 4 Automatic paper cut 4 5 Winder drive 4 6 Partition drive Control commands 5 1 Control command table 5 2 Printer driver 5 3 Control command details Character code table 6 1 Domestic code table 6 2 Overseas character code table 6 3 International character code table Cable 7 1 B501 power cable O10 AN ON OD 10 11 12 12 16 17 17 18 18 18 19 20 20 39 40 41 42 1 Overview 1 1 Overview The printer is categorized as following Net 1 2 3 4 1 Paper width 2 2 inches 3 3 inches 2 Paper setting 1 Paper holder type 2 Drop in type 3 Interface P Parallel R Serial D Parallel Serial compatible 4 OEM number D type is parallel and serial compatible Interface co
10. n has the following meaning Euch iege e epu 1 O Printer Invalid Valid 1 Notdefined 2 Notdefined 3 Notdefined 4 Notdefined 5 Notdefined 6 Notdefined 7 Notdefined f printer is not in no selection status printer will discard all received data until it is in the selection status by this command Even if printer is in no selection status the status may become BUSY by printer operation The default value of is 01 h 38 Print position alignment lt lt a gt gt 32 Code lt 1B gt h lt 61 gt h n lt 00 lt lt 02 gt h Description Aligns all data to be printed on the assigned position in a line n values are assigned to n Hex This command is valid only when it is input at the head of a line The default value of is OO h 39 Total cut Full cut lt lt ESC 1 gt gt The command functions differently between Standard and Windows models Code lt 1B gt h lt 69 gt h Standard Full cut the paper Effective at the head of a line Feeds paper by 3mm after paper cut to prevent from paper jam Windows Full cut the paper after feeding by 21 25mm Effective at the head of a line Feeds paper by 3mm after paper cut to prevent from paper jam 40 Partial cut lt lt ESC m gt gt The command functions differently between Standard and Wi
11. 0 resets inverted character The command is only valid when it is assigned at the beginning of a line The default value of n is OO h 25 90 clockwise rotated character set and reset lt lt ESC V gt gt Code 1B 56 h n 00 lt lt 01 h Sets and resets 90 clockwise rotated character Underline cannot be assigned to the 90 clockwise rotated character has the following meaning n hex 00 reset 90 rotated character set 90 rotated character Default value for is 00 h 26 Absolute position set lt lt ESC n1 2 gt gt The function of this commands differ between Standard type and Windows type Code 1B 24 h 1 2 00 lt n1 lt FF h 00 lt 2 lt 02 h Print start position is assigned dots 1 203rd of inch from the beginning of line Divide the value of dot by 256 place quotient to n2 and remainder to n1 The print start position is n1 n2 x 256 from top of the line Setting which exceeds end of line is ignored If the command is received in the middle of line the action will be Standard the value that does not exceed the current position is ignored Windows the value that does not exceed the current position is also valid 27 Relative position set lt lt lt ESC n1 n2 gt gt Code 1B h 5C h n1 n2 00 lt n1 lt FF h 00 lt 2 lt 02 h Print start position is assigned by dots from current position in unit of 1
12. 1dot doubl e 11 Underline set reset lt lt n gt gt Code 1B h 20 h n 00 lt n lt 02 h Sets and resets the underline Underline is valid for all characters except for the area skipped by horizontal tab Also Underline is not valid for 90 rotated character Underline is verified with n value as shown bellow n hex Type of underlines 00 Reset underline Set one dot underline Set two dot underline Default value is 00 h 12 1 6th of an inch line feed pitch lt lt ESC 2 gt gt Code 1B h 32 h Sets one line feed to 1 6th of an inch 13 Sets smallest pitch line feed lt lt ESC 3 n gt gt Code 1B h S3 h n 00 lt lt FF h Sets a line feed pitch to n 203rd of an inch Despite of height set by value the same space with character height is sent by line feed The default value of n is 22 h If nz OO h is set printer will not feed by pressing FEED button 14 Printer initialization lt lt ESC gt gt Code 1B h 40 h Clears the data stored in the print buffer and resets each setting to default values It does not clear the data stored in the internal receive buffer Rewrites the DIP switchs t is stored in the internal receive buffer and activated in sequential 15 Horizontal tab position set lt lt ESC D n1 n2 NUL gt gt Code 1B 44 h n1 2 OO h 00 lt FF Sets the horizontal tab posi
13. 421 289 178 Q 244 1948 576 351 241 148 H 165 1316 390 236 162 100 L 432 3452 1030 624 429 264 43 M 332 2652 790 479 329 202 Q 276 2204 656 398 273 168 H 192 1532 454 275 189 116 35 L 489 3908 1167 707 486 299 14 368 2940 877 531 365 225 Q 310 2476 738 447 307 189 H 210 1676 498 302 207 127 1 The first code word is 4 bit length and following all code words consist of 8 bit length 2 Data bit numbers include mode indicator and character number indicators 44 NV bit image registration lt lt GS T n gt gt Code lt 1D gt h lt 54 gt h n Description Register the predetermined bit image print data It is possible to register from 0 to 2 different kinds of patterns 3 patterns In each pattern up to the maximum of 15cm length for 2 model of bit image print data can be registered up to the maximum of 11cm for 3 model and up to 7cm for 4 model can also be registered The bit image print data exceeding the maximum length is neglected The registered data is not erased when the power is set on or off or the printer is initialized has a following meanings n hex Function 00 Start of pattern 0 registration 01 Start of pattern 1 registration 02 Start of pattern 2 registration FF End of registration When registrations started in the middle of a line whole line is registered When registration ended in the middle of a line whole line is not register
14. LOW status This signal becomes LOW when a printer is in the alarm status In the LOW status all control circuits in the printer stops negative logic PE SLCT 5 Input Output signal level Outputs when roll paper becomes empty positive logic Signal to indicate on line status positive logic Standard value vede MR D Input low level VIL 0 18Vcc V Input high level 0 7 V Output low level VoL 0 7Vcc V Output high level VoH 0 7Vcc V loL4 mA 6 Input Output conditions vcc wo TRO YEG __ IN PUT VCC 1 OK 74LV574 lt 3 3 PDO PD7 TE IN PUT IN PUT ITN 155319 IN PUT AK o SLCT ERROF OUT PUT BUSY OUT PUT 10 7 Timing chart POWER 2 3 gt lt lt DATA STB BUSY T1 3500msec Max T4 500nsec Max T2 500nsec Min T5 4microsec TYP 8 Receive control When BUSY signal stays at LOW it is feasible to receive data from host computer But not feasible when BUSY signal stays at HIGH 3 2 Serial interface RS 232C 1 Synchronization Asynchronous 2 Transmission speed 4800 9600 19200 38400bps user selectable 3 A word consists of Start bit 1bit Data bit 7 or 8 bit user selectable Parity bit odd even or no parity user selectable Stop bit more than 1 bit 4 Signal polarity RS 232C Mark Logic
15. O3 h 30 Barcode height select GS h n gt Code lt 1D gt h lt 68 gt h n lt 00 lt n lt FF gt h Description Selects barcode height n shows the vertical dot number Default value of n is 162 A2 h 31 Select of HRI character print position lt lt 55 H n gt Code lt 1D gt h lt 48 gt h n lt 00 lt n lt 03 gt h Description Selects the print position of HRI characters in printing barcode n has the following meaning 00 No printing Above barcode Below barcode Above and below barcode HRI characters are the characters selected by HRI character style select Default value of n is OOJh 32 Select of HRI character style lt lt GS f n gt gt Code lt 1D gt h lt 66 gt h n lt 00 lt n lt 01 gt h Description Selects HRI character style in printing barcode n has the following meanings n hex Style 00 Font A 01 Font B Default value of n is OOJh 30 33 Download bit image definition lt lt GS n1 n2 Dn gt gt Code lt 1D gt h lt 2A gt h n1 n2 Dn lt lt 1 lt gt h lt 00 lt n2 lt 30 gt h lt n1 2 lt 51 gt h Description Defines download bit image of number of dots specified by n1 and n2 Horizontal dot numbers are obtained by n1 x 8 and vertical dot numbers by n2 x 8 Dn is bit image data Once download bit image is defined it is valid until its redefined d
16. ON S2 2 Character set Overseas Japanese OFF OFF OFF S2 3 Serial control XON XOFF DTR DSR OFF OFF OFF 52 4 Japanese settings OFF OFF OFF S2 5 Presenter Yes No OFF OFF OFF S2 6 Flash ROM Rewrite No OFF OFF OFF S2 7 Paper low end Yes No ON ON ON 52 8 Print density Thick Standard OFF OFF OFF Note 1 S2 1 OFF autocutter OFF will be in winder drive setting current consumption should be less than 200 If autocutter is connected the autocutter activates and paper is cut off It may cause paper jam 2 For writing ROM set the DIP switches as stated below and turn the power on after changing CN8 NO 1 pin LF to L position or while pressing the paper feed switch on the operation panel After the operation set the power off Rewriting Flash ROM boot program S2 6 ON and S2 2 OFF Rewriting Flash ROM F W S2 6 ON and S2 2 OFF Use S2 6 in OFF position If set ON to use the program may be destroyed For NP 215 S2 7 factory setting for near end should be set OFF For NP 415W 1 2 factory setting for emulation should be set ON de 4 1 3 Self diagnostic print 1 By performing self diagnostic print following items are checked Proper function of control circuitry Proper function of printer mechanism Print quality Control F W version DIP switch setting status Correct function of paper out sensor Head wide and head rank automatically detected lt
17. end 32 Macrodefine 32 37 ESC n Data input control 32 Position align 33 Fulcut Patialcut 33 No paper signal sensorselect_ 33 Compulsory eject 34 QR code print OA Print NV bit image 36 Download firmware 36 Black white reverse print setreset 37 Presenter eject mode select 37 Backfeed 1 37 Reset software dT Partition drive select 38 Functions differently between printer with standard type driver and Windows type Register NV bit image 36 19 5 2 Printer driver Please apply the driver stated below for using under Windows environment Please refer to the User s Manual for a driver 1 Windows 95 98 NII printer driver Windows 95 98 Version 1 00 2 Windows NT4 0 NII printer driver Windows NT4 0 Version 1 00 3 Windows 2000 NII printer driver Windows 2000 Version 1 00 5 3 Control command details 1 Horizontal tab lt lt gt gt Code 09 h Shift the print position to the next horizontal tab position Horizontal tab position is set by horizontal tab set command The default of horizontal tab position is every 8th character 9th digit 17th digit 25th digit and 33rd digit in font A Maximum digit position for NP272 is 33 and for NP 372 is 41 If the next tab position is not set this command is ignored 2 Carriage return lt lt CR gt gt Code OD h
18. long the operation may become unstable Cable should be made as short as possible If not available connect cables near the printer and place an electrolysis condenser of 2200 between power supply and ground Voltage resistance should be higher than 35V For preventing from static electric discharge make sure to connect FG wire 2 4 Reliability 1 Head life Average resistance change rate to head less than 1596 except defects caused by dust or others Pulse More than 100 million pulses with recommended paper Wear distance More than 50 km with recommended paper 2 Operation environment Temperature 0 45 Print guarantee 5 40 C no condensation 3 Storage environment Temperature 20 60 C When storing for a long time paper must be kept loaded between head and platen 4 Frame Ground FG wire The FG wire Green and Yellow is coming from the printer body Make sure to ground the wire near the body frame when installing the printer FG grounding is effective for minimizing the noise level preventing from SED and maintaining the FG safety for head cutter body frame power supply and Data connectors 5 Safety regulation CE marking UL60950 6 EMC EMI EN55022 VCCI Class A FCC Class A EMS EN55024 2 5 Dimensions 1 NP 215 dimensional drawing screw hol es to fi x frane ground 6 frane ground L 75 111 3
19. paper signal 13 SLCT Output Connection select signal 14 Not fixed For extension 19 GND Common ground 31 NNIT Input Initialize signal 32 ERROR Output Control stop signal 36 Not fixed For extension 15 18 20 30 Not fixed 35 14 and 36 are kept as HIGH Do not connect them 4 Data signal input connecter Serial Printer side connecter JEC 9S JST equivalent Mating connecter JEC 9P JST equivalent Pin Signal In Output Function Remarks 2 RXD Output Serial receive data 3 TXD Input Serial transmit data 4 DTR Output Data transmit permit signal Connect to No 7 5 GND GND for signal 6 CTS Input Transmit permit signal Connect to No 8 7 DTR Output Data transmit permit signal Connect to No 4 8 CTS Input Transmit permit signal Connect to No 6 1 9 N C 13 5 Data signal input connecter Parallel Serial Printer side connecter XG4C 2631 Omron equivalent Corresponding housing XG4M 2630 T Omron equivalent Pin Signal In Output Interface Function Remarks 1 STB Input Parallel Data read assign signal 2 PDO Input Parallel Parallel print data 0 3 PD1 Input Parallel Parallel print data 1 4 PD2 Input Parallel Parallel print data 2 5 PD3 Input Parallel Parallel print data 3 6 PD4 Input Parallel Parallel print data 4 7 PD5 Input Parallel Parallel print dat
20. table select lt lt ESC t gt gt Code 1B 74 h n 00 lt n lt 01 h Selects either Japan code table or non Japan code table Explanation n value has following meaning n Hex 00 Non Japan character code table 01 Japan character code table The default value of n is 52 2 for DIP SW 23 Printer status transmission lt lt ESC v gt gt Code 1B h 76 h Sends current printer status Status to be transmitted consist of 1 byte and the content is explained in the chart below ae remove sensor _7 not defined Make sure that command is issued before transmission of print data commands are stored in the input buffer and executed sequentially Reception is available except in the buffer full status The commands above are valid only for serial interface Regarding DTR DSR control only one byte is transmitted after confirmation that the host is able to receive data that is DSR signal is in SPACE status For XON OFF control one byte is transmitted without confirmation of DSR signal status For DTR DSR control if host is not in a receivable status it waits until host can receive data 24 Inverted character set and reset lt lt lt ESC n gt gt 28 Code 1B h ZB h n 00 lt n lt FF h Sets or resets the inverted character function n2 is only valid for the LSB bO LSB 60 has the following meaning bO Description
21. 203rd of inch Right direction is treated as plus and left as minus For assigning N dots in minus direction left it will be N dots 65536 N Divide dots by 256 quotient is n2 and remainder is n1 Assigning beyond the end of a line is neglected 29 28 Barcode print lt lt 655 Dn gt gt Code lt 1D gt h lt 6B gt h n Dn lt 00 gt h lt 00 lt n lt 07 gt h Description Selects barcode symbology and prints barcode The next print start position is on the line head ELI Select following barcode symbology with value Dn indicates the character code to be printed Barcode symbology UPC A cer ee ci 00 UPCA m UPCE 02 13 13 amp 03 EAN 8 JAN 8 04 CODE39 5 5 amp 5 05 ITF a 06 CODABAR 07 1 128 When there is data the buffer this command is neglected f character code Dn is not a printable character following data after Dn will be treated as normal data If the print character numbers are fixed in the barcode symbology the input character numbers should match to the print character numbers If horizontal data exceed one line the exceeded data cannot be printed 01 02 03 04 05 07 29 Barcode width size select GS w gt gt Code lt 1D gt h lt 77 gt h n lt 02 lt n lt 04 gt h Description Selects width of barcode Default value of n is
22. 3 Definable characters are from lt 20 gt h to lt 7E gt h in ASCII code 95 characters 4 Dn indicates the data to be defined It indicates the dots pattern from the left Remaining area on the right of a character is filled with spaces 5 Once a download character is defined it remains valid until the download character is redefined printer is initialized reset signal is input or the power is turned off 6 Only area specified will be reset 21 lt Reference gt In the case of FontA 12dots 24dots P12 000 h P4 000 h P7 000 h P10 001 h 2 000 h P5 00 h P8 h P112 720 h P3 080 h P6 F8 h P9 081 h P12 001 h 22 lt Reference gt In the case of Font 17dots P12 400 4 7F h P72 410 10 41 h 2 04 5 0 FCO h P8 0 040 h P11 0 041 h P3 000 h P6 000 h P9 000 h P12 001 h 23 10 Bit image mode set lt lt ESC n1 2 gt gt Code 1B h 2A n1 2 Dn m bit image mode refer to below h 00 lt n1 lt FF h 00 lt 2 lt 02 h Data is printed in bit image by following the bit image mode specified by m Print total dots divided by 256 quotient is n2 and remainder is n1 Total dots in bit image mode are n1 256 x n2 If the bit image input data exceeds specified position the exceeded data will be disregarded 215 225 432 dots NP 325
23. 576 dots NP 415W 832dots Bit image data Dn interprets bit 1 as print and bit 0 as not print Bit image mode is indicated below If m is out of conditions set the data after n1 is treated as normal data Standard Vertical direction Horizontal direction m Bit image Maximum dot number hex mode E cack NP 215 NP 325 NP 415W quanty y Y NP 225 B 00 9908 8 67DPI 1010 216 288 416 single density 01 8 dots 8 67 203DPI 432 576 832 double density 20 24905 24 203DPI 101DPI 216 288 416 single density 21 24 dots 24 203DPI 203DPI 432 576 832 double density Windows Vertical direction Horizontal direction m Bit image Maximum dot number hex made an dons eni NP 215 NP 325 NP 415W iind NP 225 20 249065 24 2030 67DPI 144 192 277 single density 21 24 dots 24 2030 101DPI 216 288 416 double density 22 249015 24 203DPI 135DPI 288 384 554 single density 23 24 dois 24 203DPI 203DPI 432 576 832 double density 24 dots 203DPI 432 832 832 24 double density 24 203DP 864 1664 1664 The data for Windows 24h is equivalent to m 23h due to the mechanical specification 24 lt Relationship between bit image data and printed dots gt 8 dots bit image D1 D2 D3 L 1dot 24 dots bit image L
24. E Input Collector of At High phototransistor Paper out 3 SG Signal ground Cathode or emitter connect 4 SG Signal ground Valid when DIP SW S2 7 is on When PNE signal is High PE signal of CN5 outputs Printing operation is not affected 14 8 8 Connect to operation panel Printer side connector 53047 0310 Molex Mating connector 51021 0300 Molex Pin Signal name In Output Functions Remarks 1 LF Input Paper feed signal input Active at L 2 ALM Output Printer error signal Output in Output printer error 3 SG Signal ground there is no paper line feed is not executed Paper feed is executed according to the paper feed pitch set by ESC 2 ESC 3 However if While paper feed signal is at L set Power on to activate self diagnostic printing While paper feed signal is at L release INIT signal to to activate diagnostic printing ALM signal for operation panel indicates printer statuses as follows A protective resistance is incorporated on the board a light diode can be located between 2 and 3 2 anode and cathode Normal status Print receive ready No paper Load the paper Head up status Set head down F W write mode Set the power on again Presenter in cramp status Pull out the clamped paper Head temp high 80 c Printer returns normal at head temp of 60 c Wrong head connection Connect head cable prope
25. This command is ignored 3 Line feed lt lt LF gt gt Code h Prints data stored in the input buffer and executes line feed according to data of feed pitch 4 Page feed lt lt FF gt gt This command is effective only in Windows mode Code OC h Prints data in the print line buffer and executes page feed to the head of next page according to the page length in the setting Default setting for the page length is 66 lines 5 n line page length setting lt lt ESC C gt gt Code AB 43 h n 01 lt n lt FF h Sets a page length for n lines with current line feed pitch Position is set to the head of page iia Default value for n is 42 h for 66 lines If printer is initialized the head of page is also initialized Line pitch change after setting will not change page length 6 Setting right space of a character lt lt ESC SP n Code 1B 20 n 00 lt lt 20 Sets the right space of a character by unit of dot 1 203 of an inch the case of double width mode the space will be doubled The default value of is 00 h ELI 20 7 Overall print mode setting lt lt ESC gt gt Code 1B 21 h n 00 lt n lt FF h Sets print mode has following meanings Character font 1 p coq ue Undefined 2 Undefined 6 Undefned 7 Underline Reset Set If doub
26. a 5 8 PD6 Input Parallel Parallel print data 6 9 PD7 Input Parallel Parallel print data 7 10 Output Parallel Data processing end signal 11 BUSY Output Parallel Receive data not ready signal 12 PE Output Para Ser No paper signal 13 SLCT Output Parallel Connection select signal 14 Not fixed For extension 15 ERROR Output Para Ser Control stop signal 16 NNIT Input Para Ser Initialize signal 17 Not fixed For extension 18 19 GND Para Ser Ground for signal 20 LF Input Para Ser Paper feed signal 21 TXD Output Serial Transmit data 22 RXD Input Serial Receive data 23 CTS Input Serial Transmit permit signal 24 DTR Output Serial Data transmit permit signal 25 GND Para Ser Signal ground 26 VH Input Para Ser DC 24V Connect GND and DC 24V to stabilize circuit Since 14 and 17 are kept as HIGH do not connect them 6 CN6 Autocutter sensor control switch motor Printer side connector 5483 04AX Molex Mating connector 5480 04 Molex Pin Signals Input output Functions 1 Output Motor drive signal 2 M Output Motor drive signal 3 CSW1 Input HP detect SW output 4 CSW2 HP detect SW GND 7 CN7 Auxiliary sensor paper near end sensor Printer side connector 53047 0310 Molex Mating connector 51021 0300 Molex Pin Signal name In Output Functions Remarks 1 LED Output Anode of LED 2 PN
27. ce Error signal becomes LOW In the case of serial interface Error signal becomes LOW and error bit in the status information is set to 2 Return to normal status from error statuses Remove causes of error statuses and turn the power on again or input the INIT signal to return to normal When this process is activated at the time of power switch turned off the printer will be initialized so that settings are required again If data remains in the buffer attention should be paid 4 3 Buffer full print If there remains data in the buffer after one line of data is received printer automatically prints preceding data The volume of buffer full data varies depending on ASCII characters or bit images 17 4 4 Automatic paper cut Automatic paper cut after paper is manually fed by pressing FEED button If manual line feed is conducted for more than 10 lines the paper is automatically cut off after the paper feed is finished This function is not available when the line feed is conducted by control command 4 5 Winder drive 4 6 When no autocutter is mounted autocutter drive motor functions as external rewinder drive CN6 Autocutter sensor control switch Outputs to motor pins 1 and 2 52 1 OFF rewinder drive ON autocutter drive DC motor with DC 24V approx 200mA In about 1 to 2 sec rewinder output is turned OFF after printing and paper feed If overloaded with higher current than specified and the status c
28. data exceeds the area to be printed QR code is not printed 34 Following table shows the number of characters and input data capacity for the model 1 in version 1 to 14 Version Corrector Data eode Data bit Numeric Apra Byte Kanji level Word numeric L 19 148 40 24 17 10 4 M 16 124 33 20 14 8 Q 13 100 25 15 11 6 H 9 68 16 10 7 4 L 36 284 81 49 34 20 2 M 30 236 66 40 28 17 Q 24 188 52 31 22 13 H 16 122 33 20 14 8 L 57 452 131 79 55 33 3 M 44 348 100 60 42 25 Q 36 284 81 49 34 20 H 24 188 52 31 22 13 L 80 636 186 113 78 48 4 M 60 476 138 84 58 35 Q 50 396 114 69 48 29 H 34 268 76 46 32 19 L 108 860 253 154 106 65 5 M 82 652 191 116 80 49 Q 68 540 157 95 66 40 H 46 364 105 63 44 27 L 136 1084 321 194 134 82 6 M 106 844 249 151 104 64 Q 86 684 201 122 84 51 H 58 460 133 81 56 34 L 170 1356 402 244 168 103 7 M 132 1052 311 188 130 80 Q 108 860 253 154 106 65 H 72 572 167 101 70 43 L 208 1660 493 299 206 126 8 M 160 1276 378 229 158 97 Q 128 1020 301 183 126 77 H 87 692 203 123 85 52 L 246 1964 585 354 244 150 9 M 186 1484 441 267 184 113 Q 156 1244 369 223 154 94 H 102 812 239 145 100 61 L 290 2316 690 418 287 177 10 222 1772 526 319 219 135 Q 183 1460 433 262 180 111 H 124 988 291 176 121 74 L 336 2684 800 485 333 205 11 256 2044 608 368 253 156 208 1660 493 299 205 126 145 1156 342 207 142 87 L 384 3068 915 555 381 234 12 292 2332 694
29. ed Following is a command sequence of pattern 0 registration GS T Oh bit image data assigned by ESC lines GS T FFh 45 NV bit image print lt lt GS gt gt Code lt 1D gt h lt 50 gt h n lt 00 lt lt 02 gt h Description Prints the bit image print data registered Selects one of the print pattern among three registered patterns by assigning 0 to 2 value to 46 Firmware download lt lt GS d gt gt Code lt 1D gt h lt 64 gt h Dn Description Download printer firmware in hexadecimal code and rewrite firmware according to the outcome Dn is firmware s hex code which complies with INTELLEX Hex format 36 47 Reverse print set and reset lt lt GS gt gt Code lt 10 gt lt 42 gt lt 00 lt n lt FF gt h Function Sets and resets reverse print is available only for the least significant bit The characters incorporated and downloaded can be reverse printed The right side space of character set by Set right space of a character is also included for reverse print However it does not cover the skipped space made by bit image download bit image NV bit image barcode HRI characters horizontal tab specify absolute position specify relative position t does not include the space between the lines Reverse print has a priority over underline specified If a character is reversed the characte
30. in sequence When the cutter is in a movement soft reset is executed after finishing cutting 37 51 Partition drive select lt lt lt GS n gt gt Code lt 10 gt 1 lt 25 gt lt 01 lt lt 03 gt h Description Selects partition drive n indicates the following n HEX Divide 01 1 fixed partition 02 2 fixed partitions 03 automatic partition Default value is selected by the DIP switch 1 or 2 partitions If assigned beyond the specified area the data is neglected and the select will not change Automatic partition is as follows 1 partition 2 partitions NP 215 225 Less than 215 dots More than 216 dots NP 325 Less than 287 dots More than 288 dots NP 415W Less than 415 dots More than 416 dots 52 Print density set Code Description lt lt GS n gt gt lt 1D gt h lt 7E gt h n lt 00 lt n lt FF gt h Sets print density in the range between 65 135 of the standard value S2 8 Off n ranges from 41h 65 to 87h 135 However set it for actual use in the 41h 65 lt n lt 82h 130 At the initial status 100 or 125 can be selected by the DIP switch S2 8 This command has priority over the setting by DIP switch range 38 ae or fae aL HE F 42 ba gt EX ES E Em gt S A a EN E JH C Ol P je v je m lt elza e e
31. is 00 h 18 Print and smallest pitch line feed lt lt ESC J n gt gt Code 1 4A h n 00 lt n lt FF h Prints the data in the print line buffer and feeds the paper n 203rd of an inch The height of character for a line is always sent by line feed If the value of height is set by n below the height of character the same space with character height is sent by line feed Beginning of a line is a print start position 19 International character select lt lt ESC R gt gt Code 1B h 52 h n 00 lt lt 0 h Selects the international characters REI The values of n have following meanings 00 USA France 06 Itay 08 Japan sd 0A 09 Norway 0A Denmak2 Default value of n is 27 20 Panel switch enable disable lt lt ESC c 5 gt gt Code AB 63 35 h n 00 lt n lt FF h Changes the FEED switch valid or invalid n is only valid for LSB bO bit has a following meanings Description 0 enable FEED switch disable FEED switch Default value of n is OO h 21 Print and n line feed ESC gt gt Code 1B 64 h n 00 lt n lt FF h Prints the data in the print buffer and feeds paper by lines Beginning of a line is a print start position If there is print data remained line feed is activated for the same height of character 22 Character code
32. le height and double width are set at the same time quadruple character will be formed All of the printed characters will be underlined except for the 90 rotated characters and spaces created by horizontal tab Underline width is determined by the value set in Underline set reset section The default value is 1 Different sizes of character mixed such as double width and normal size can be printed The default value of is 00 h 8 Down load characters set reset lt lt n Code 1B h 25 h n 00 lt n lt FF h Setting or resetting the characters to be downloaded Unable to use download character set amp download bit image set at the same time Only LSB b0 is valid for n value LSB 50 has the following meanings Function 0 Resets download chraracter 1 Sets download chraracter Default value is 00 h 9 Definition of download character lt lt ESC amp n m a Dn gt gt Code NB 26 5 03 20 lt lt 7 20 lt lt 7 h font A 00 lt lt 0 h font B 00 lt lt 09 h Definition of download character such as alpha numeric 1 s indicates a number of bytes in a vertical direction and is a number of dots in horizontal direction 2 indicates the start character code and means the end character code If only 1 character should be defined then n m
33. n noise during printing 4 Print ink disappears on low print durability paper 5 Electrolyte corrosion on thermal head due to low quality of heat receipt layer Avoid printing with no paper loaded It damages platen and thermal head Do not scrabble thermal head with sharp edge or something hard or give impact The heat element may be damaged Set the power of printer off before connecting or removing connecters When printing in high speed under low temperature of high humidity environment the paper may be stained by moisture that appears from paper or the printer may have condensation Avoid dew from dropping down to the thermal head that may cause electrolyte corrosion Turn the power off until any dew is removed The printer is not protected from water or dew formed Do not water the printer or handle it with a wet hand which may cause damage to the printer due to short circuit or heat or fire The printer is not protected from dust or dirt If it is used at dusty place the thermal head may be damaged or paper feed is not operated properly When cleaning the printer with a vacuum cleaner avoid the printer s paper outlet from locating cleaner s air inlet The printer s main structure parts use plated steel However rust may be caused to the cut section Reflection type of infrared ray sensors are used at some locations in the printer Direct sun light may cause mal function of printer Avoid from such a location for installation
34. ndows models Code lt 1B gt h lt 6D gt h Standard Partially cut paper with one point left uncut at the center position Effective at the head of a line Feeds paper by 3mm after paper cut to prevent from paper jam Windows Partially cut paper with one point left uncut at the center after feeding paper by 21 25mm Effective at the head of a line Feeds paper by 3mm after paper cut to prevent paper jam 41 No paper sensor select lt lt 3 n1 2 gt gt Black mark sensor command Code lt 1B gt h lt 63 gt h lt 33 gt h n1 n2 lt 00 lt 1 lt 01 gt h lt 00 lt n2 lt FF gt n1 0 no paper sensor thermal paper n1 1 black mark sensor label paper Value n2 is available only at label selection in n1 Feeds paper by dots assigned after label position is confirmed Minimum amount of paper feed 0 125mm Feeds 0 125mm x n2 amount of paper Default value selects the thermal paper Auto loading function is not available at label selection 33 42 Compulsory eject lt lt ESC gt gt Code lt 1B gt h lt 72 gt h n lt 0 lt lt 1 gt h When a ticket or receipt is cramped and it is left untaken for a certain period of time this command is used to execute compulsory eject This command rotates a motor either clockwise or counter clockwise until ticket or receipt is ejected totally n Hex Mode 0 Clockwise 1 Counter clockwise
35. nnector is not incorporated NP 415 W 1 2 3 1 Windows driver available 2 Interface P Parallel Serial D Parallel Serial compatible 3 OEM number D type is parallel and serial compatible Interface connector is not incorporated 1 2 Features This module printer is designed on the basis of our long experience as a printer manufacturer Individual unit such as printer mechanism controller board and auto cutter is assembled in compact with our reliable design concept Simple integration to the system requiring only power and data supplies that contributes to the short development time and improvement of product reliability 1 Important areas such as paper entrance and auto cutter guide are designed professionally on the basis of our long experience as a printer manufacturer Small compact and light weight Easy to integrate into various kinds of system Short development time High speed and quality of printing Both parallel and serial interfaces are available as a standard Various barcode symbols 1 D and 2 D QR code are available 7 Various kinds of application are available Possible to control paper presenter paper transfer and present device User friendly drop in type of roll paper holder with paper end sensor 1 0 Windows drivers Windows95 98 NT4 0 2000 are available 1 Easy to write rewrite F W by using flash memory Also 3 patterns of registration are available with NV bit image
36. ontinues the ICs may be damaged Partition drive The fixed drive 1 or 2 partition drives or automatic partition drive can be selected by the DIP switch and commands It should be selected according to the power supply and print duty 1 Fixed partition Function ON OFF 51 3 Fixed partition select 2 partitions 1 partition 1 NP 415W is assigned to 2 fixed partitions 2 2fixed partition select may decrease print speed 3 2 fixed partition select may decrease print quality 2 Automatic partition drive 1 partition 2 partitions NP 215 225 Less than 215 dots Higher than 216 dots NP 325 Less than 287 dots Higher than 288 dots NP 415W Less than 415 dots Higher than 416 dots 1 Automatic partition drive select will automatically change the print speed according to print ratio Print noise may appear 2 The default value selected by commands will be the fixed partition selected by The DIP switch Refer to the section 5 3 3 Automatic partition select may decrease print quality 18 5 Control commands 5 1 Control command table Controlcodes_ Functions Pages 6 ESCSPn j Characterrightspaceset 20 8 ESC n Downloadcharactersetireset 21 9 ESC amp snmaDn Download character definition 21 26 31 GSHn HRI character print position select 30 33 GS n1 n2 Dn Download bit image define 31 Macro definition start
37. ownload character is defined external characters are specified software is reset power is set off or INIT signal is input Download bit image cannot be defined at the same time with download characters or external characters If this command is executed download character definition or external characters contents are cleared The relationship between bit image data amp defined dots is shown below n1x8dots MSB n2x8dots dn1xn2x8 34 Download bit image print lt lt GS m gt gt Code lt 1D gt h lt 2F gt h m lt 00 lt m lt 03 gt h Description Prints download bit image in a mode assigned by m Modes to be assigned by m are as follows 00 Normal mode _ 203dpi 203dpi f there are some data left in the print buffer this command is neglected If download bit image is not defined yet this command is neglected Download bit image data exceeding 1 line cannot be printed Download bit image cannot be defined at the same time with download character or external characters 31 35 Macro definition start and end lt lt lt GS gt gt Code lt 1D gt h lt gt h Description Assigns Macro definition start and end The size of data defined by Macro is up to 1 024 bytes Exceeding to 1 024 byte cannot be defined Defined Macros cannot be cleared by Printer initialization Therefore printer initialization can be incl
38. r is not underlined However the underline setting remains effective f highlight or double strike is set on the reverse print the print may result in damages 48 Presenter eject mode selection lt lt lt ESC h n gt gt Code lt 1B gt h lt 68 gt h n lt 00 lt lt 01 gt h Description Selects either cramp eject or total eject for the presenter paper eject mode indicates the following n HEX Function 00 Cramp eject 01 Total eject Default value is 00 h 49 Back feed lt lt ESC Bn gt gt Code lt 1B gt h lt 42 gt h n lt 00 lt n lt FF gt h Description Feed the paper backward Paper feed amount is specified by n dot line Paper is not fed backward when O is set f this command is used for many times paper may be jammed To avoid this problem enter only once and feed paper in the forward direction Double strike print is available by using this command Considering the backlash there may be a gap of printing When data remains in the print line buffer it first prints data then back feeds Paper might get jammed while a presenter is in use In this regard please do not use the command once paper is set in the presenter 50 Software reset lt lt DC1 gt gt Code gt lt 11 gt h Description Restart the firmware as the same procedure as power on This command is stored in the receive input buffer and activated
39. rly Auto cutter error Remove jammed paper and turn Presenter error 9 CN9 Connect to presenter NPT 301 only Printer side connector 53047 0810 Mating connector 51021 0800 power on again or input INIT signal Pin Signal Input output Remarks 6 LED Output To sensor LED1 7 Sensor 1 Input From sensor 1 8 SG Signal GND 9 LED2 Output To sensor LED2 10 Sensor2 Input From sensor2 11 SG Signal GND 12 M Output Motor drive output 13 M Output Motor drive output Connect to NPT 301 only When connect to other product it would cause problems 15 4 Functions 4 1 Function setting 4 1 1 DIP switch S1 Factory setting Function ON OFF BP 5R 5D 1 1 Interface Serial Parallel OFF ON OFF 1 2 Select emulation Windows ESC POS OFF OFF OFF 1 3 Select fixed division 2 partition 1 partition OFF OFF OFF 1 4 Baud rate Refer to the following OFF OFF OFF S1 5 table OFF OFF OFF S1 6 Parity check Yes No OFF OFF OFF S1 7 Parity bit Odd Even OFF OFF OFF S1 8 Data bit 7 bit 8 bit OFF OFF OFF Baud rate 4 800bps 9 600bps 19 200bps 38 400bps 1 4 OFF OFF ON ON 1 5 OFF ON OFF ON 4 1 2 DIP switch S2 Factory setting Function ON OFF 5p 5R 5D S2 1 Auto cutter Yes No ON ON
40. s Font lt 3 Print mode 4 Barcode specs 4 Line spacing Default 1 D symbology Vertical double Quadruple Bold Double strike Inverted 90 clockwise rotation Black white reverse Underline 4 25 mm 1 6 inch ANK mode Bit image mode Barcode mode UPC A UPC E EAN 13 JAN 13 EAN 8 JAN 8 CODE39 ITF 2 qe 11 Receiving buffer Operation SW Low sensor 4 Papers recommended Net weight Outer 218mm CODABAR NW 7 lt lt CODE128 lt lt 2 0 symology QR code lt lt 5 Interface Parallel Centronics lt lt Serial RS 232C lt lt 6 Auto cutter 1 Cut method Guillotine type lt lt 2 Applicable paper Thermal 65 125 lt 3 Cut cycle 30 cuts minute lt lt 4 Cut mode by command Total cut lt lt setting Partial cut a 2mm tab left at the center 5 Life time 300 000 cuts lt lt 7 1 Paper width 60 mm 80 mm 112mm specs 2 Max diameter 80 mm 083 mm 283 mm 83 mm 3 Core diameter Inner 212mm TFSOKS E2D Nihon Seishi PD160R N Shin Oji Seishi AFP235 Mitsubishi Seishi TL69KS R2 Nihon Seishi TL69KS HW74 Nihon Seishi TC98KS T1 Nihon Seishi ALMLED OUT Line feed SW input approx 550g 650g approx 750g Approx 22 5
41. ter P type R type Printer side connector TCS7960 532010 Hoshiden Mating connector TCP8927 53 1100 TCP8935 53 1100 Hoshiden Equivalent Pin Signal name Input Output Function 1 VH Input Power DC 24V 2 GND Power ground 3 Not available Shell FG FG A sufficient volume of power supply is required to maintain print quality due to high peak current that may run according to printing If power supply cable is excessively long the operation may become unstable Cable should be as short as possible If not available connect cables near the printer and place an electrolysis condenser of 2200 between power supply and ground Voltage resistance should be higher than 35V Make sure to connect FG wire to prevent from ESD problems 12 3 Data signal input connecter Parallel Printer side connecter 57 40360 DDK equivalent Mating connecter 57F 40360 20N DDK equivalent Pin Signal In Output Function Remarks 1 STB Input Data read assign signal 2 PDO Input Parallel print data 0 3 PD1 Input Parallel print data 1 4 PD2 Input Parallel print data 2 5 PD3 Input Parallel print data 3 6 PD4 Input Parallel print data 4 7 PD5 Input Parallel print data 5 8 PD6 Input Parallel print data 6 9 PD7 Input Parallel print data 7 10 Output Data processing end signal 11 BUSY Output Receive data not ready signal 12 PE Output No
42. tion 1 indicates the digits number from the left In this case tab position 1 2 Tab position is set at the location of character width x n from the beginning of a line The character width in this case includes character right space When double width function is set then the width becomes double of ordinary character 3 Maximum number of tab positions is 32 If setting exceeds 32 then the exceeded values are neglected 4 lt ESC D gt clears all tab positions being set After the tab is cleared horizontal tab will be ignored 5 Default value is set at every 8 characters of font A at 9th 17th 25th and 33rd digit 26 16 Bold print set reset lt lt ESC n gt gt Code 1B h 45 h n 00 lt lt FF h Sets and resets the bold print n is only valid for LSB bO LSB b0 is defined as following Values 0 Resets bold print Sets the bold print Valid for all characters Bold print and double strike results in the same on this printer The default value of is OOJh 17 Double strike set reset lt lt lt ESC n gt gt Code 1B h 47 h n 00 lt n lt FF h Sets and resets the double strike function is only valid for LSB bO ELI Control by n is explained as following bo Description 0 Resets double strike Sets double strike Double strike and bold print result in the same on this printer The default value of n
43. uded in the Macro definition During the Macro definition printing can be proceeded Once Macro is defined the contents become effective until software is reset power is set off or INIT signal is input 36 Macro execution GS n1n2n3 gt gt Code lt 1D gt h lt 5E gt 1 2 lt 0 lt n1 lt FF gt h lt 00 lt n2 lt FF gt h lt 00 lt 3 lt 01 gt h Description Executes Macros defined The definitions of n1 n2 and n3 are n1 times of Macro execution n2 wait time of Macro execution At every execution there is a wait time of n2 x 100msec n3 Macro execution mode 00 Consecutive execution Execution by FEED switch Consecutive execution Executes n1 times with a wait time specified at n2 FEED switch execute After a time specified at n2 waits for PE LED blinks and the FEED switch depressed After FEED switch is pressed it executes Macro once This action is repeated by n1 times f the printer receives this command during Macro definition it stops Macro definition this happened defined Macros are cleared Nothing happens if Macro is not defined or n1 0 During Macro execution with n3 1 line feed by FEED switch is disabled 37 Data input control lt lt ESC gt gt Code lt 1B h 3D h lt 00 lt n lt FF gt h Description Selects valid device where data input is possible through host computer REI Each bit of
Download Pdf Manuals
Related Search