Stamina Products 55-1537C User's Manual
Contents
1. Insert the Ball Pins in the lowest adjustment holes in the Angle Adjustment Tubes to restrict the movement of the inversion bed to the least amount of inversion angle Use this setting until you have verified your height setting and become familiar with the Elite Inversion System Both Pivot Arms must always be adjusted to the same hole You must understand how to recover from the fully inverted position before using the fully inverted position Read the RECOVERY FROM LOCKED POSITION section at the bottom of page 14 BEFORE using the fully inverted position Always insert the Ball Pins into the same adjustment hole on both sides of the Elite Inversion System Do not allow children to use or play on the Elite Inversion System Keep small children and pets away from the Elite Inversion System at all times The Elite Inversion System should not be used by persons weighing more than 300 lbs The Elite Inversion System should not be used by persons over 6 feet 6 inches tall It is recommended that you place this exercise equipment on an equipment mat Use the Elite Inversion System only on a level surface Wear appropriate clothing when exercising do not wear loose clothing that could become caught in the Elite Inversion System Be sure that there is enough room for the bed to rotate completely Use the Elite Inversion System only as described in the manual The safety level of the Elite Inversion System can be maintained only if it is examined2. PARTS LIST DIAGRAM PART NAME Front Frame Left Rear Frame Right Rear Frame Base Frame Handrail Height Adjustment Beam Footrest Adjustment Knob Heel Holder Tube Heel Holder Bracket Heel Holder Inner Pad Tube Outer Pad Tube Foam Pad Left Lever Cover Right Lever Cover Rear Lever Cover Corner cap Lever Claw Spacer Spring Button Hand Grip Bushing Spring Pin Locking Knob 3 8 16 x 3 4 Nylon Bed Foam Grip Selection Tube Bushing Left Shaft Clip Right Shaft Clip Tension Spring Long Ball Pin 8 x 55mm Bumper Stand A front left Stand B front right Hollow Cap Oval Plug 20mm x 60mm Dome Plug 22mm Round Plug 22mm Round Plug 25mm Square Plug 38mm x 38mm Support Washer Screw Round Head M4 x 20mm Bolt Button Head M6 x 1 x 15mm Bolt Button Head M6 x 1 x 35mm 17 QTY PARTS LIST DIAGRAM 60 61 62 63 64 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 91 92 93 PART NAME Bolt Button Head M6 x 1 x 47mm Bolt Button Head M6 x 1 x 55mm Bolt Button Head M8 x 1 25 x 15mm Bolt Button Head M8 x 1 25 x 50mm Bolt Button Head M8 x 1 25 x 55mm Nylock Nut M6 x 1 Nylock Nut M8 x 1 25 Washer M6 x 16 x 1 5mm Thick Washer M8 Arc Washer M8 Arc Washer M6 Warning Label Combination Wrench Allen Wrench 4mm Allen Wrench 6mm Manual Claw Pressing Bar Assembly Bolt Button
3. SC WIND 7 Owner s Manual ELITE INVERSION SYSTEM CAUTION 1 Weight on this product should not exceed 300 Ibs 2 Class H equipment This equipment is for home use only It is not for commercial use N WARNING N Exercise can present a health risk Consult a physician before beginning any exercise program with this equipment If you feel faint or dizzy immediately discontinue use of this equipment Serious bodily injury can occur if this equipment is not assembled and used correctly Serious bodily injury can also occur if all instructions are not followed Keep others and pets away from equipment when in use Always make sure all bolts and nuts are tightened prior to each use Follow all safety instructions in this manual When calling for parts or service please specify the following number 55 1537C STAMINA PRODUCTS MADE IN CHINA Product May Vary Slightly From Pictured This Product is Produced Exclusively by S NMUNI 2040 N Alliance Springfield MO 65803 Customer Service Number 1 800 375 7520 www staminaproducts com 2006 11 2006 Stamina Products Inc TABLE OF CONTENTS Safety Instructions 2 Maintenance Instructions 15 Before You Begin 4 Product Parts Drawing 16 Hardware Identification Chart 5 Parts List 17 Assembly Instructions 6 Warranty 19 Operational Instructions 11 Notes 20 Storage 15 Fax Mail Ordering Form 22 SAFETY INSTRUCTIONS WARNING To reduce the risk o
4. Inc P O Box 1071 Springfield Missouri USA 65801 1071 or call us at 1 800 375 7520 If the defect is covered under this limited warranty you will be requested to return the product or part to us for free repair or replacement at our option NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE 1 YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE 1 YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER This limited warranty is not transferable IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU In the event that the purchaser makes any claim under this limited warranty or any implied warranty the Warrantor reserves the right to require the product to be returned for inspection at the purchaser s expense to the Warrantor s premises in Springfield Missouri Return of the enclosed warranty registration card is not required for warranty coverage but is merely a way of establishing the date and place of purchase Stamina Products Inc SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT LOSS OF TIME INCONVENIENCE COMMERCIAL LOSS OR ANY OTHER INDIRECT CONSEQUENTIAL SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED WARRANTY This limited warranty is the only writt
5. PADS 18 3 To release your feet or relax the grip pull the LEVER 23 toward you slightly and press the button on the end of the lever THE HANDRAILS For added convenience and satety a set of HANDRAILS has been added to the Elite Inversion System These HANDRAILS are located at both sides of the frame The HANDRAILS are to help you return to the upright position from any degree of inversion If you wish to return to the upright position and the bed is moving too slowly or not moving at all simply grab the HANDRAILS and pull on them until you return to the upright position 12 OPERATIONAL INSTRUCTIONS USING THE PRO INVERSION SYSTEM 1 2 3 Start by lying fully back on the bed with your hands at your side or resting on your thighs Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate backward Stop or lower your arms to control the downward rotation of the table Raise your arms until they are over your head At this point the inversion table will be as far back as it can go As you get more comfortable with the use rock the bed slowly by moving your arms up and down slowly Agentle swinging motion will alternately put your spine in traction and compression This rhythmic type of traction is used by many hospitals and doctors to treat certain back problems Iit is recommended that the inversion table be used for five or ten minutes each morning and again ea
6. your feet are higher than your head dismount and try a taller setting If you do not rotate to a position close to level dismount and try a shorter setting NOTE The Elite Inversion System should return to the upright position when your hands are below your waist If it does not use a taller setting 11 OPERATIONAL INSTRUCTIONS INVERSION ANGLE ADJUSTMENT There are 11 adjustment holes in the ANGLE ADJUSTMENT BARS 85 allowing you restrict the movement of the NYLON BED 37 to different angles by inserting the PULL PINS 86 into different adjustment holes The top holes will allow the least amount of inversion angle The lowest hole will allow the greatest amount of inversion angle and the Elite Inversion System will go into the full inversion position CAUTION 1 Use the holes near the top in the ANGLE ADJUSTMENT BARS 85 until you become familiar with the Elite Inversion System 2 Both PULL PINS 86 must be inserted into the same hole in the ANGLE ADJUSTMENT BARS 85 Trying to insert the PULL PINS 86 into different positions could cause damage to the machine and injury to the user HEEL HOLDER USE AND ADJUSTMENT Button 1 Place your feet on the FOOTREST 11 with your ankles between the HEEL HOLDERS 15 and FOAM PADS 18 2 The HEIGHT ADJUSTMENT BEAM 10 includes a LEVER 23 to grip and release your feet Pull the LEVER 23 toward you until your ankles are securely held between the HEEL HOLDERS 15 and FOAM
7. 0 81 and NYLOCK NUTS M10 80 Lock the FRONT FRAME 1 in the unfolded position with the LONG BALL PINS 46 ASSEMBLY INSTRUCTIONS STEP 3 Slide the bottom of the two PIVOT ARMS 91 into the brackets located at each side of the MAIN FRAME 92 Align the desired hole on the arm with the peg on the bracket then insert the peg into the hole to lock the PIVOT ARMS 91 in position Secure the PIVOT ARMS 91 with the SECURING KNOBS 3 8 16 x 1 2 93 on the inner side of the brackets PIVOT ARM ADJUSTMENT There are three adjustment holes on the PIVOT ARMS 91 allowing you to position the MAIN FRAME 92 at three different heights The lowest hole will allow the least amount of inversion angle The top hole will allow the greatest amount of inversion angle CAUTION 1 Use the lowest holes in the PIVOT ARMS 91 until you become familiar with the Elite Inversion System 2 Both PIVOT ARMS 91 must be adjusted to the same hole Trying to adjust the PIVOT ARMS 91 to different positions could cause damage to the machine and injury to the user STEP 4 Attach the MAIN FRAME 92 onto the REAR FRAMES 2 3 by sliding the slots in the ends of the two PIVOT ARMS 91 into the slots on the REAR FRAMES 2 3 and secure with the SHAFT CLIPS 43 44 ASSEMBLY INSTRUCTIONS STEP 5 Attach the ANGLE ADJUSTMENT BARS 85 onto the shafts on both sides of the MAIN FRAME 92 with BOLTS M8 x 15mm 62 and WASHERS M8 69 Do not tighten the
8. 7 and HEIGHT ADJUSTMENT BEAM 10 then bolt them together with BOLT M6 x 35mm 59 and ARC WASHER M6 71 WARNING The PAD TUBES 16 17 must be assembled with the ends pointed downward as shown The ends must be pointed downward to properly secure the users feet in place during inversion Improper assembly will allow the user s feet to come loose and the user will fall from the Elite Inversion System 9 ASSEMBLY INSTRUCTIONS STEP 10 Install the HEIGHT ADJUSTMENT BEAM 10 into MAIN FRAME 92 by pulling the SPRING PIN 35 on the MAIN FRAME 92 and inserting the HEIGHT ADJUSTMENT BEAM 10 as shown For added safety thread the LOCKING KNOB 3 8 16 x 3 4 36 into back side of the MAIN FRAME 92 WARNING Do not use the Elite Inversion System until you have verified your height setting Failure to use the proper height setting can result in difficulty recovering from the decline position See HEIGHT ADJUSTMENT instructions on page 11 STEP 11 Insert the front ends of the HANDRAILS 5 onto the short tubes on REAR FRAMES 2 3 Then attach the back ends of the HANDRAILS 5 with BOLTS M8 x 50mm 63 and WASHERS M8 69 10 OPERATIONAL INSTRUCTIONS GENERAL PRECAUTIONS 1 Use the lowest holes in the PIVOT ARMS 91 until you become familiar with the Elite Inversion System 2 Do not use the Elite Inversion System alone Always have a helper available in case assistance is needed in recovering from the decline position Make sure t
9. AIL CUSTOMER SERVICE CUSTOMER SERVICE CUSTOMER SERVICE STAMINA PRODUCTS INC Tel 1 800 375 7520 Fax 417 889 8064 partsOstaminaproducts com ATTN Customer Service cust srvcOstaminaproducts com P O Box 1071 www staminaproducts com Springfield MO 65801 1071 7 Detach and Mail or Fax the Form Below 7 Stamina Products Inc P O Box 1071 Springfield MO 65801 1071 Mr Ms Address Apt City State Zip Code IMPORTANT We must have your phone number in order to process the order Phone Work Phone Date Purchased Model Purchased From IMPORTANT Before filling out the form below make sure you have the right information Refer to the parts list to make sure you re ordering the right parts PART DESCRIPTION QUANTITY Rear Unit Assembly ME
10. Head M6 x 1 x 42mm Bolt Button Head M10 x 1 5 x 60mm Nylock Nut M10 x 1 5 Washer M10 Nut M8 x 1 25 Pressing Bar Spacer Support Sleeve Angle Adjustment Bar Pull Pin 86 x 40mm Instruction Video DVD Pivot Arm Main Frame Securing Knob 3 8 16 x 1 2 18 QTY de N N NDNPNN lt ANNRN 4 4 4 4 4 4 4NONIRNOUOON LIMITED WARRANTY MODEL 55 1537C WARRANTY Stamina Products Inc warrants that this product will be free from defects in materials and workmanship under normal use service and proper operation for a period of 90 days on the parts and 5 years on the frame from the date of the original purchase from an authorized retailer THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE ABUSE MISUSE ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR REPLACEMENT SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED BY STAMINA PRODUCTS INC Commercial use includes use of the product in athletic clubs health clubs spas gymnasiums exercise facilities and other public or semipublic facilities whether or not the product s use is in furtherance of a profit making enterprise and all other use which is not for personal family or household purposes To implement this limited warranty send a written notice stating your name date and place of purchase and a brief description of the defect along with your receipt to Stamina Products
11. acking the unit open the hardware bag and make sure that you have all the following items Some hardware may be already attached to the part Part No and Description Qty 59 Bolt Button Head M6 x 1 x 35mm 60 Bolt Button Head M6 x 1 x 47mm 62 Bolt Button Head M8 x 1 25 x 15mm 64 Bolt Button Head M8 x 1 25 x 55mm 79 Bolt Button Head M10 x 1 5 x 60mm 66 Nylock Nut M6 x 1 67 Nylock Nut M8 x 1 25 80 Nylock Nut M10 x 1 5 i 63 Bolt Button Head M8 x 1 25 x 50mm Z y 68 Washer M6 x 16 x 1 5mm Thick 69 Washer M8 81 Washer M10 TOS 70 Arc Washer M8 71 Arc Washer M6 NM 1 1 NNN RO mb ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you Remove all packing materials from your area and place them back into the box Do not dispose of the packing materials until assembly is completed Read each step carefully before beginning If you are missing a part please call our toll free number for assistance 1 800 375 7520 or e mail us at parts staminaproducts com STEP 1 Insert the LEFT and RIGHT REAR FRAMES 2 3 into the BASE FRAME 4 and secure with BOLTS M8 x 55mm 64 ARC WASHERS M8 70 WASHERS M8 69 and NYLOCK NUTS M8 67 STEP 2 Slide the upper ends of the FRONT FRAME 1 into the Brackets on the LEFT and RIGHT REAR FRAMES 2 3 and secure with BOLTS M10 x 60mm 79 WASHERS M1
12. bolts until STEP 6 STEP 6 Slide one of the SUPPORT SLEEVES 84 onto the left ANGLE ADJUSTMENT BARS 85 Install the SUPPORT SLEEVES 84 onto the shaft on the LEFT FRAME 2 with the SUPPORT SLEEVE 84 above the shaft as shown in the illustration and secure with a BOLT M8 x 15mm 62 and WASHER M8 69 Insert the PULL PIN 86 into one of the Adjustment Holes in ANGLE ADJUSTMENT BAR 85 Repeat on the other side Tighten all the bolts ASSEMBLY INSTRUCTIONS STEP 7 Attach the FOOTREST 11 onto the HEIGHT ADJUSTMENT BEAM 10 with the adjustment holes facing down Secure the FOOTREST 11 in place with the ADJUSTMENT KNOB 12 NOTE The four adjustment holes in the FOOTREST 11 allow the FOOTREST 11 to be attached in four different positions Start with one of the center positions and adjust if necessary Use the outer position if users are taller than average Use the inner position if users are shorter than average STEP 8 Insert the HEEL HOLDER TUBE 13 through the hole on the HEIGHT ADJUSTMENT BEAM 10 and secure with BOLT M6 x 47mm 60 WASHERS M6 x 816 x 1 5mm Thick 68 and NYLOCK NUT M6 66 Place aHEEL HOLDER BRACKET 14 onto aHEEL HOLDER 15 then slide them onto the HEEL HOLDER TUBE 13 together Repeat on other side STEP 9 Insert the OUTER PAD TUBE 17 through the hole on the HEIGHT ADJUSTMENT BEAM 10 Insert the INNER PAD TUBE 16 into the OUTER PAD TUBE 17 Align the holes on the INNER PAD TUBE 16 OUTER PAD TUBE 1
13. ch evening Return to the upright position by slowly moving your hands back down to your thighs 13 OPERATIONAL INSTRUCTIONS SUGGESTIONS FOR USE 1 Begin slowly invert with the least amount of inversion angle to begin with Stay inverted only as long as you are comfortable Return upright slowly 2 Make gradual changes increase the angle only ifitis comfortable Increase the angle only one adjustment hole at a time Increase the time of use 1 2 minutes up to ten over a period of weeks Add stretching and light exercise only after you are comfortable with inversion 3 Watch your body come up slowly dizziness after a session means you came up to fast Wait a while after eating before using table If you get nauseous do not fight it come up as soon as you feel queasy 4 Keep moving movement while inverted encourages blood lymph and spinal fluid circulation and aids in alignment of bones and organs Movement may be accomplished by either rhythmic traction or light exercise Do not exercise strenuously while inverted Limit partial inversion without movement to one or two minutes Limit full inversion with no movement to only a few seconds 5 Invert regularly we recommend two or three times a day depending upon your current condition Try to schedule it for the same times each day LOCKING THE BED When the inversion table rotates past the vertical inverted position the bed becomes lo
14. cked and will not return to the upright position in the usual way The locked position allows you to hang straight upside down completely free of the bed This position allows you to enjoy all of the benefits of a handstand with none of the discomforts as shown in illustration A It also allows you to do exercises such as the waistband as shown in illustration B To get into the locked position use the top hole in the PIVOT ARMS 6 as described in STEP 3 If necessary adjust the HEIGHT ADJUSTMENT BEAM 10 shorter and then mount and use normally When your arms are completely extended above your head the bed will rotate all the way to the locked position CAUTION You must understand how to recover from the fully inverted position before using the fully inverted position Read the RECOVERY FROM LOCKED POSITION section below BEFORE using the fully inverted position RECOVERY FROM LOCKED POSITION To recover from the locked position simply grab the HANDRAILS and pull on them while pushing back on the HEEL HOLDERS 15 with your legs If you can not reach the HANDRAILS then you can still recover by grabbing the back of the bed with one hand the REAR FRAME with the other and pulling your hands together as shown in illustration C 14 STORAGE The Elite Inversion System is designed to fold for easy storage You can store your Elite Inversion System as illustrated Please follow the following process STEP 1 Loosen LOCKING KNOB 36 and p
15. en or express warranty given by Stamina Products Inc This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state ANY OTHER RIGHT WHICH YOU MAY HAVE INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to disclaim or limit implied warranties and consequential and incidental damages with respect thereto If any such law is found to be applicable the foregoing disclaimers and limitations of and on implied warranties and consequential and incidental damages with respect thereto shall be disregarded and shall be deemed not to have been made to the extent necessary to comply with such legal restriction 19 NOTES 20 NOTES 21 FAX MAIL ORDERING FORM Please do not return the product For your convenience Stamina has a Customer Service Department with a toll free number Should a part be missing or a defective part found please call 1 800 375 7520 in the U S from 7 30 A M to 5 00 P M Central Time Monday through Thursday and 8 00 A M to 3 00 P M on Friday or fill out the fax sheet ordering form below and fax it to 417 889 8064 Our Customer Service Department will be able to assist you with your problem and the part will be mailed directly to your house TELEPHONE FAX ONLINE M
16. ent toll free number 1 800 375 7520 Monday Friday 8 00 A M 5 00 P M Central Time BEFORE YOU BEGIN Thank you for choosing the Elite Inversion System We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better look better and enjoy life to ts fullest Yes it s a proven fact that a regular exercise program can improve your physical and mental health Too often our busy lifestyles limit our time and opportunity to exercise The Elite Inversion System provides a convenient and simple method to begin your assault on getting your body in shape and achieving a happier and healthier lifestyle Before reading further please review the drawing below and familiarize yourself with the parts that are labeled Read this manual carefully before using the Elite Inversion System Pivot Arm Right Shaft Clip Handrail Main Frame Lever Foam Pad Footrest Stand B Front Frame Stand A THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY EE Although Stamina tries to manufacture its products with the finest materials and uses the highest standards of manufacturing occasionally a part that does not fit is the incorrect size or is otherwise inappropriate is found Even with the highest inspection and quality controls in place these things will happen occasionally Please do not return the product For your convenience Stamina has a Cu
17. f serious injury read the following safety instructions before using the Ti 12 13 14 15 16 17 18 19 20 21 22 23 24 Elite Inversion System Read all warnings posted on the Elite Inversion System The Elite Inversion System should only be used after a thorough review of the Owner s Manual We recommend that two people be available for assembly of this product Do not use the Elite Inversion System alone Always have a helper available in case assistance is needed in recovering from the decline position Make sure that the Pivot Arms are assembled using the same hole on both Pivot Arms Pay close attention to Steps 3 and 4 on page 7 Make sure that the Pivot Arms are always secured to the pegs on the Main Frame with the Quick Releases Make sure that the Pad Tubes are assembled with the ends pointed down as directed in STEP 9 on page 9 The ends must be pointed downward to properly secure the users feet in place during inversion Improper assembly will allow the users feet to come loose allowing the user to fall from the inversion table Do not use the Elite Inversion System until you have verified your height setting Failure to use the proper height setting can result in difficulty recovering from the decline position See HEIGHT ADJUSTMENT instructions on page 11 Always make sure that your feet are properly secured in the heel Holder mechanism when using the Elite Inversion System
18. hat the FOAM PADS 18 and HEEL HOLDERS 15 are holding your feet securely Make sure that the HEIGHT ADJUSTMENT BEAM 10 is properly set for your height 5 Make sure thatthe HEIGHT ADJUSTMENT BEAM 10 is held securely by both the SPRING PIN 35 and the LOCKING KNOB 36 6 Make sure that there is enough room for the bed to rotate completely RO HEIGHT ADJUSTMENT The Elite Inversion System is a very sensitive balance device It responds to very slight changes in weight distribution It is very important to make sure that the height adjustment is adjusted properly Use the following procedure to set the height adjustment and balance the Elite Inversion System 1 Insert the PULL PINS 86 into the second adjustment holes from the top in the ANGLE ADJUSTMENT BARS 85 to restrict the movement of the NYLON BED 37 to the least amount of inversion angle The PULL PINS 86 should not be inserted into the lowest adjustment holes in the ANGLE ADJUSTMENT BARS 85 or the Elite Inversion System may go into the full inversion position while you are setting the height adjustment 2 Loosen the LOCKING KNOB 36 under the MAIN FRAME 92 3 Pull the SPRING PIN 35 and use the SCALE INDICATION to set the HEIGHT ADJUSTMENT BEAM 10 4 Tighten the LOCKING KNOB 36 5 Mount the machine 6 Lock your ankles into the FOAM PADS 18 and HEEL HOLDERS 15 7 Lie back with your hands at your sides 8 Slowly raise your hands to your chest 9 If
19. regularly for damage and wear This equipment is for home use only It is not for commercial use WARNING Before using this equipment you should consult with your personal physician to see if inversion equipment is appropriate for you Do not use this equipment without your physician s approval Do not use this equipment if you have any of the following conditions or ailments Extreme obesity Glaucoma retinal detachment or conjunctivitis Pregnancy Spinal injury Cerebral Sclerosis or acutely swollen joints Middle ear infection High blood pressure Hypertension Recent stroke or Transient ischemic attack Heart or circulatory disorders for which you are being treated Hiatus hernia or Ventral hernia Bone weaknesses including Osteoporosis Unhealed fractures Medullary pins or Surgically implanted orthopedic supports Use of anti coagulants including Aspirin in high doses CALL US FIRST IOAN I CUSTOMER SERVICE NUMBER 1 800 375 7520 THANK YOU FOR PURCHASING THE Elite Inversion System To help you get started we have pre assembled most of your Elite Inversion System at the factory with the exception of those parts left unassembled for shipping purposes Simply follow the few assembly instructions set forth in this manual Within a few minutes you will be getting your body into shape and on your way to achieving a happier and healthier lifestyle Should you have any questions please call our Customer Service Departm
20. stomer Service Department with a toll free number If a part is missing does not fit is the incorrect size or is otherwise inappropriate please call 1 800 375 7520 in the U S between 8 00 A M and 5 00 P M Central Time Monday through Friday Our operators will be able to assist you with your problem and the parts will be mailed directly to your house Nylon Bed Handrail Angle Adjustment Bar Left Rear Frame Base Frame Stand B Adjustment Beam Heel Holder Combination Wrench Allen Wrench 4mm Allen Wrench 6mm HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process Place the washers the end of the bolts or screws on the circles to check for the correct diameter Use the small scale to check the length of the bolts and screws 3 16 1 4 516 3 8 1 2 O C 25 INCHES 0 1 2 1 1 2 1 2 1 2 1 2 5 1 2 6 T T T T T T T T T T In EHEEBEZEBEZEBEBSEN BEE EL PA A 0 10 20 30 40 50 60 80 90 100 110 120 130 140 150 Q Q Q MILLIMETERS ath VAN NOTICE The length of all bolts and screws except those with flat heads is measured from below the head to the end of the bolt or screw EG length Flat head bolts and screws are measured from the top of the head to the end of the bolt or screw VA ____ 3 After unp
21. ull out the SPRING PIN 35 Now slide the HEIGHT ADJUSTMENT BEAM 10 into the MAIN FRAME 92 and lock in the lowest adjustment hole Refer to illustration 1 STEP 2 Remove the PULL PINS 86 from the ANGLE ADJUSTMENT BARS 85 Swing the NYLON BED 37 down to about the same place as the Rear Frame and lock in position by inserting the PULL PINS 86 into the second adjustment holes in the ANGEL ADJUSTMENT BARS 85 above the SUPPORT SLEEVE 84 Refer to illustration 2 STEP 3 Remove the LONG BALL PINS 46 from the REAR FRAMES 2 3 Fold the Front Frame close to the Rear Frame as Illustration 3 shows Insert the LONG BALL PINS 46 back into the REAR FRAMES 2 3 to lock the Elite Inversion System in the folded position WARNING When folding and unfolding the Elite Inversion System keep all children away from the Elite Inversion System and make sure your hands are clear of any folding or pinch point Insert the PULL PINS 86 46 into the second adjustment holes 84 MAINTENANCE The safety level of the Elite Inversion System can be maintained only if it is examined regularly for damage and wear 1 Check the angle adjustment tube traction bars ball pins pivot arms cushion bed heel holders foam pads spring pin and warning label for damage and wear 2 Replace damaged and worn components immediately and or keep the equipment out of use until repairs are complete PRODUCT PARTS DRAWING
Download Pdf Manuals
Related Search