Square SP4200 User's Manual
Contents
1. 55 degree Modeling Power Halogen 100w Synch Voltage 5 volt Fuse 6A Dimension 4 x 7 1 2 Weight 1 8 Lb 800g 1 On Off electric supply 5 Flash test 9 Flash digital readout 2 Variable flash buttons 6 Sync receptacle 10 Remote button 3 On Off variable model lamp 7 Safety fuse 11 Flash ring 4 On Off flash ready beep 8 AC receptacle 12 Model lamp SAFETY PRECAUTIONS Become thoroughly familiar with this product before use Run Wait until the bulb is completely cool before touching or through at least one practice assembly and breakdown before removing it you schedule a shoot Never use the SP160 lamp outside in a wet environment Make sure that the main voltage corresponds to that stated on Never move the appliance by pulling the cord Make sure the the SP160 lamp Account for number of lamps in use cords do not come in contact with halogen bulb Do not wind Never leave the lighting unsupervised when in use Keep the cord around the appliance children or incompetent persons away from lighting equipment Stand the SP160 on a flat surface only to prevent toppling If the lamp or the cord show sign of wear or damage it should Do not touch the metal parts on the lamp while in use these be replaced or repaired by a qualified electrician before use metal parts will become very hot Softbox Assembly 1 Pictured is the SP4 lamp ring 2 Small end of flex rod fits into 3 With three ro2. SQUARE o PERFECT y CMake every picture perfect ove SP4200 VARIABLE POWER STUDIO FLASH SET e e gt vy o Qty 3 Qty 1 Qty 3 Qty 3 Qty 1 Qty 1 Qty 1 Qty 1 Qty 1 Qty 2 SP4200 Professional Series Studio Light Kit SP200 Professional Studio Digital Strobes 200 Watt Seconds 75 watt modeling light Boom and counter weight bag with carrying case Light Stands extends 39 to 8 1 2 Softbox 24 X 24 Umbrella 36 silver reflection umbrella Strobe Case Carries three strobes and accessories Carry Bag Carries three light stands and umbrella Backdrop stand with carry bag 10 x20 Backdrop 10 x13 Black and 10 x13 White backdrop Accessories Oty 1 Collapsible Reflector 22 double sided Silver White amp Qty 1 Four Leaf Barndoor Qty 1 Set of 4 Color Gels Qty 1 Honeycomb Diffusion Filter 9 Qty 1 Narrow Snoot SQUARE Make every picture perfect www squareperfect com SP4200 Flash Studio Kit Thank you for your purchase of the SP4200 Flash Softbox Studio Please read this manual carefully before use and keep it handy kit This manual has been written to help you with the assembly for use during break down of equipment Please read and heed all operating procedures and accessories Square Perfect s SP4200 safety precautions listed in this manual To order spare bulbs Flash Kit is manufactured with the finest material available Your or r
3. d socket 3 Switch the receiver unit ON OFF button to the ON position Press the test button located on the top of the trigger unit You will see a twinkling of the LED on the receiver unit This indicates the trigger is working properly and is locked in on a working channel ofthe receiver to fit most popular brands The DRT 2G trigger has two channels and uses a 23 battery installed The DRT 2G receiver uses two AAA batteries notincluded 4 Switch the remote flash unit power Switch to the ON position with the DRT 2G receiver attached Push the test button on the DRT 2G trigger it should trigger the remote flash unit 5 To change channels on the DRT 2G trigger slide the channel switch on the side of the trigger device to the opposite position Next press the power switch on the receive unit twice to reset the receiver To order spare bulbs or replacement parts contact us at info squareperfect com Also check out our extended line of photo equipment SQUARES PERFECT www squareperfect com
4. ds inserted into 4 Next insert the fourth rod 5 Insert the forth rod into the connector shown with the corner pocket on the softbox the ring and corners fold the into the SP 4 ring Note Keep pocket on the velcro strap large end of the flex rod inserted tent SP 4 ring into the tent the velcro flaps at the ring open to allow sufficient slack 6 Push the velcro strap into 7 Now close the velcro flaps 8 The SP 4 ring can now be 9 Next attach the inner diffusion 10 Attach the outer diffusion place just below the lip of the as shown in the picture attached to the SP 160 flash unit lens with the velcro straps lens to velcro patches on tent Note the rods take a good DO NOT over tighten the outer edges deal of force to flex into position Technical Notes for the electronic radio trigger device The SP Flash Kit is shipped with the DRT 2G electronic radio flash triggering device for your convenience It is an easy to use device that will give you extra control in the photographic studio environment The DRT 2G is designed to work with a variety of flash units We provide a wide range of sync cord adaptors 1 To use the DRT 2G trigger device first slide the trigger into the hot shoe found ontop on your camera If a hot shoe is not available use the sync cord attachment found on the side ofthe trigger device 2 Attach the receiver to a remote flash unit Use the proper sync cord adaptor provided plug into sync cor
5. eplacement parts contact us at info squareperfect com flash kit will provide many years of quality service with proper care Also check out our extended line of photo equipment now and handling available Flash Studio Kit Includes Nylon Carry Case Compartmentalized for easy use 1x2 SP200 lamp body 12 power cord Electronic radio trigger 1x3 Four panel softbox set 1 Fourleaf barndoor receiver with sync cord and with lamp connector adaptors 1x1 Flat reflector for creativi fill techniques includes carry case 1x1 Complete backdrop stand with carry case 1x1 Snoot will direct light to exact spot without 1x1 Umbrella double 1 Red blue yellow frosted affecting surrounding layered reflective and honeycomb filter area inside light proof backing 1x3 SP8061 professional duty adjustable light stand Stand extends from 39 to 8 1 2 1x8 Four panel softbox set with lamp connector 1x1 Varigated dye backdrop 1x1 Black backdrop 1x1 White backdrop 1x1 Twelve foot boom with adjustable weight counter balance bag SP200 Lamp Head Operation Specifications Power Input AC110 130 volt 50 Hz Flash Power 200w joule in full Guide No GN45 Color Temperature 5600K Flash Tube Lifetime over 8 000 typical flashing Flash Power Setting 1 32 to full Recharge Time 2 seconds in full Flash Duration 1 600 sec 1 1000 sec Slave Range 35ft 10m Lighting Range
Download Pdf Manuals
Related Search