Speco Technologies LEDomeW Dome Camera User's Manual
Contents
1. LEDome IR DAY NIGHT DOME CAMERA EXTERNAL IR LEDS amp CDS SENSOR BUILT IN HEATER WEATHERPROOF COMPOSITE AND UTP VIDEO OUTPUTS speco technologies 200 New Highway Amityville NY 11701 631 957 8700 CHECK LIST Check list EE Cautions Features Installation rememora 4 Adjustment of Led Array T TY 5 Operation amp wiring diagrams 6 7 Internal Components 8 Function Selection T 9 14 Dimension m 15 Specification nnne 16 Please make sure that the following items are included in the package LEDome Camera 4 Mounting Screws 1 Allen Wrench 1 Allen Bit 1 Video Test Cable 1 Power Cable Adaptor for optional use Please leave this manual with the end user for future reference Function Selection Function Selection 2 BLC Back light compensation Use if there is a strong light or sunshine behind the object The coverage of BLC is center plus bottom as below 3 FIL Flicker Less ON Locks the electronic shutter to 1 100 and allows the auto iris full control of light adjustment 4 L L Line Lock Syncs the camera to the 60 Hz phase of the electrical circuit Can only be used in 24 Volt AC operation If a camera shows wavy or unstable picture make sure that L L is turned off 5 LUX DIP SWITCH M 152. a 2step 3sTep gt 4StTEP LUX DIP SWITCH Tells the camera when to switch to the B W night mode Note Only one switch can be in the position at time 1 The camera will switch at 1 2 lux 2 The camera will switch at 1 lux 3 The camera will switch at 3 lux 4 The camera will switch at 5 lux 6 ALRAM SWITCH 1 2 MICRO SWITCH FOR ALARAM Select N O or N C Function Selection Function Selection Default settings of the internal DIP switches 4 Function DIP SWITCH 5 LUX DIP SWITCH 1 iset 2 ai 25 3 F L mi 3SETP 40 gt 4SETP Adjust the DIP switches to suit the requirements of your installation Switch Mode Function 5 DIP SWITCH M aM 28Lc 3FA gt 1 ELC Electronic light compensation ON Electronic Shutter is active OFF Electronic shutter is locked at 1 60 and the DC Auto Iris is in complete control of the light adjustments INSTALLATION Adjustment of LED Array Connections 1 When using 12 Volts DC constant voltage 600mA CONNECT POWER TO THE POWER JACK POWER INPUT RED e Connect CENTER 2 When using 24 Volts AC 40 VA CONNECT ACCESSORY CABLE TO THE POWER JACK AND CONNECT AC 24V TO THE LEAD POWER INPUT RED connect CENTER 3 CONNECT VIDEO CABLE CONNECT BNC CABLE TO T
3. CEMENTS NECESSITATED BY ANY CAUSE BEYOND THE RESULT OF MANUFACTURE INCLUDING BUT NOT LIMITED TO ANY MALFUNCTION DEFECTS OR FAILURE CAUSED BY OR RESULTING FROM UNAUTHORIZEO SERVICE OR PARTS MPROPER MAINTENANCE MODIFICATION OR REPAIR BY THE USER ABUSE MISUSE NEGLECT ACCIDENT FIRE FLOOD OR OTHER ACTS OF GOD INCORRECT UNE VOLTAGE DAMAGE OR MAGE BURNS TO TELEVISION PICTURE TUBES CAUSED BY OR ATTRIBUTABLE TO THE USE OF ANY ACCESSORY ELECTRONICS GAME OR DEVICE OR DAMAGE CAUSED TO IMAGE PICKUP TUBES BY EXCESSIVE LIGHT THE FOREGOING 1 IN LIEU OF ALL OTHER EXPRESSED WARRANTIES AND WE DO NOT AUTHORIZE ANY PARTY TO ASSUME FOR US ANY OTHER OBLIGATION OR LIABILITY IN NO EVENT SMALL WE BE LIABLE FOR INCIOENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF THIS PRODUCT OR FOR ANY DELAY IN THE USE OF THES PRODUCT DUE TO CAUSES BEYOND OUR CONTROL SOME STATES DO NOT ALLOW LIMITATIONS OF HOW LONG IMPLIED WARRANTY LASTS ANDIOR DO NOT ALLOW THE EXCLUSION OR LMITATION OF CONSEQUENTIAL DAMAGES THE ABOVE LIMITATIONS ON IMPLIED WARRANTY AND CONSEQUENTIAL DAMAGES MAY NOT APPLY TO YOU WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE NOTE FOR YOUR PROTECTION IN THE EVENT OF THEFT OR LOSS OF THIS PRODUCT PLEASE FILL IN THE INFORMATION REQUESTED BELOW AND RETAIN WITH YOUR SALES RECEIPT MODEL NO SERIAL NO 3 LOCATED ON BACK OR BOTTOM SIDE OF UNIT DATEOFPURCHASE WHERE
4. HE BNC JACK YELLOW VIDEO T asa Note All connections can be made directly to the PCB if desired 4 CONNECT UTP CABLE if desired This wires directly to the PCB in the dome housing PS Sg UTP TP Adjustment LED array Adjustment of LED Install the dome camera and aim the Vari focal lens Loosen 1 3 Led array fixing screw Aim the IR LED array in the direction that the camera is looking Connect the IR LED array to the closest connector on the PCB Tighten the IR LED array using the three screws m e N 1 Loosen the set screw located on both sides of the IR LED array box 2 Aim the IR LED array in the same direction as the lens 3 Tighten both set screws on the IR LED array CAUTIONS FEATURES LEDome should only be installed by qualified personnel Please use only 24 Volt AC or 12 Volt DC Power supply To prevent a fire or electrical hazard please use proper power cables Please make sure that the ceiling or wall is strong enough to hold the weight of the camera The Dome Cover should be treated with care Do not clean the cover with an abrasive cleaning material Please use a soft cloth or tissue to clean the dome cover There are no user serviceable parts inside Please do not disassemble this camera other than to make initial adjustments WEATHERPROOF amp TAMPER RESISTANT DIP SWITCHES FOR BLC ELC F L amp LINE
5. LED S activate needed Optional heads are available 3 DAY NIGHT DC AUTO IRIS LENS Mechanical IR filter exchange Adjust between T 2W TELE gt WIDE to set the angle focal length Set the focus by adjusting gt 3N NOTE BOTH OF THE ABOVE ADJUSTMENTS GET LOCKED INTO POSITION THROUGH THE USE OF LOCKING HANDLES 1 VIDEO TEST TERMINAL 2 V PHASE 3 DC IRIS LEVEL 4 DIP SWITCH 5 LUX DIP SWITCH 6 ALARM SWITCH 1 2 1 VIDEO TEST TERMINAL Allows you to connect a test monitor for making adjustments 2 V PHASE LEVEL When desired the vertical phase may be adjusted to sync the vertical phase of the camera with other cameras in the sys tem This feature is only available in 24 volt AC operation 3 DC IRIS LENS LEVEL DC IRIS level adjustment for the auto iris lens DIMENSION SPECIFICATION OD 2 GOGOOOOG IMAGE SENSOR 1 3 SONY EX VIEW CCD TV SYSTEM NTSC SCANNING SYSTEM 2 1 INTERLACED SYNG SYSTEM LINE LOCKED ADJUSTABLE V PHASE LINE LOCK INTERNAL ON OFF RESOLUTION MINIMUM ILLUMINATION 480 TV LINES 0 03 LUX IR OFF 0 00 IR ON CDS SENSOR SIN RATIO PHOTOCONDUCTIVE CELLS ADJUSRABLE IN 4 STEPS MORE THAN 5048 GAMMA CHARACTERISTIC VIDEO OUTPUTS 1 0Vp p 75ohm COMPOSITE UTP Balun built in ELECTRONICSHUTTER SHUTTER POWER REQUIREMENTS 045 1 60 1 100 000 sec 24 Volls AC 12 Volt
6. LOCK DUAL VOLTAGE 24 VOLTS AC 12 VOLTS DC MECHANICAL IR FILTER FOR DAY NIGHT FUNCTION 1 3 SONY EXVIEW CCD SENSOR AUTO IRIS DAY NIGHT DC VARIFOCAL LENS 4mm 9mm TURBO AGC BUILT IN ALARM AND TAMPER SWIITCHES 360 DEGREE ADJUSTABLE IR LED ASSEMBLY VIDEO TEST CONNECTOR FOR EASY INSTALLATION DAY NIGHT LUX LEVEL SELECTION SWITCH TO CUSTOMIZE YOUR INSTALLATION BUILT IN HEATERS BUILT IN 25 IR LED S amp CDS SENSOR OPTIONAL LARGER HEADS ARE AVAILABLE FOR GREATER RANGE UTP AND COMPOSITE VIDEO OUTPUTS HANGING STRAP FOR DOME COVER NO REFLECTION FROM THE IR LEDs Note Specification are subject to change without notice Operation amp wiring diagram Operation amp wiring diagram How to operate 1 Set the direction zoom and focus of the camera Make any necessary internal dip switch settings 2 Connect the video and power leads System Configurations 1 Single system gt 3 Input Power 2 QUAD system Ly Input Power Input Power input Power es a input Power 2 DVR system ig Internal Components Function Selection 1 Structure 1 HEATERS 2 IR LED ARRAY 3 DAY NIGHT DC Auto Iris M I d Lens 4 9MM 1 HEATERS To prevent moisture and extend the operating range of the camera The heaters are thermostatically controlled 2 IR LED S Infrared
7. PURCHASED PURCHASE PRICE FOR MORE INFORMATION REGARDING SERVICE OR RETURN CALL US AT TOLLFREE 1400245 5516 IN METRO NY 601 867 8709 ALWAYS USE DISCRETION WHEN INSTALLING VIDEO AND OR AUDIO SURVEILLANCE EQUIPMENT ESPECIALLY WHEN THERE IS PERCEIVED PRIVACY OR AN EXPECTATION OF PRIVACY INQUIRE REGARDING FEDERAL STATE AND OR LOCAL REGULATIONS APPLICABLE TO THE LAWFUL INSTALLATION OF VIDEO AND OR AUDIO RECORDING OR SURVEILLANCE EQUIPMENT PARTY CONSENT MAY BE REQUIRED
8. s DC POWER CONSUMPTION OPERATIONAL TEMPERATURE 40F to 122F WEIGHT 22 Pounds WARRANTY MEMO LIMITED WARRANTY TS WARRANTY IS VALID ONLY ON PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA THS WARRANTY APPLIES ONLY TO THE ORIGINAL USER SUBJECT TO CONDITIONS AND EXCLUSIONS FOUND BELOW THIS PRODUCT IS WARRANTED AGAINST MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE FOLLOWING PERIOD FOR PARTS AND LABOR PRO VIDEO CAMERAS 2 YEARS PRO VIDEO MONITORS A YEAR BALANCE OF PRO VIDEO LINE VEAR Time lapse VER Orum Assemblies and Meads 0 0AY8 WE WILL REPAIR OR REPLACE AT OUR OPTION ANY PARTS FOUND TO BE DEFECTIVE FOR THE WARRANTY PERIOD SPECIFIED WE WILL PROVIDE A REPLACEMENT FOR ANY DEFECTIVE PART sonomons THS WARRANTY WILL BE HONORED ONLY ON THE PRESENTATION OF THE ORIGINAL DATED BLOF SALE TRANSPORTATION OF THE PRODUCT OUA SERVICE STATON B HE RESPONSIBILITY OF THE USER REPAIRED OR REPLACED PRODUCT VILL BE RETURNED PREPAID DURING THE WARRANTY PORE EXCLUSIONS THIS WARRANTY SHALL NOT COVER ADJUSTMENT OF CUSTOMER OPERATED CONTROLS AS EXPLAINED IN THE APPROPRIATE MODEL S INSTRUCTION MANUAL OR PRODUCTS WHICH HAVE BEEN ALTERED ABUSED OR HAVE MISSING OR ALTERED SERIAL NUMBERS 2 TWS WARRANTY SHALL NOT APPLY TO UNCRATING SETUP INSTALLATION OR THE REMOVAL AND REINSTALLATION OF PRODUCTS AFTER REPAIR 2 THiS WARRANTY SHALL NOT APPLY YO REPAIRS OR REPLA
Download Pdf Manuals
Related Search