Spalding 21166904 User's Manual
Contents
1. injury 11 DO NOT OVERTIGHTEN NUT 52 ONTO BOLT 56 BRACKET 47 SHOULD MOVE FREELY 10 04 P N 21166904 Run the cable from strut assembly around the pole through the hole in the vertical support 18 and down through the hole in the cable bracket as shown 20 Place one nut on top of the cable bracket and one below as illustrated Tighten the bottom nut until 1 8 of thread is exposed as illustrated Opposite Side View 13 10 04 P N 21166904 B Begin trigger assembly by pulling wire through slot on trigger 48 as shown Complete this assembly by installing trigger to plates with bolt 53 and bolt 58 NOTE DO NOT OVERTIGHTEN NUT 42 ONTO BOLT 58 TRIGGER 48 SHOULD MOVE FREELY P N 21166904 10 04 14 15 10 04 P N 21166904 RIM ASSEMBLY amp INSTALLATION Install carriage bolt 41 through rim 25 washers 4 and 27 as shown Tighten nut 43 completely Place nut 42 about half way up carriage bolt 41 as shown AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE 39 to backboard and suppor2. Customer Service Center V N53 W24700 South Corporate Circle Sussex WI 53089 U S A A Huffy Sports Company WRITE IN YOUR MODEL NUMBER ss In Ground Basketball System Owners Manual AA SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly Check entire box and inside all packing material for parts and or additional instructional material Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document If using a ladder during assembly use extreme caution Two 2 people are reccomended for this operation Seat the pole sections properly Failure to do so could allow the pole sections to separate during play Before digging contact utility company to locate underground power cables gas and water lines Ensure there are no overhead power lines within 20 ft 7 m radius of pole location Climate co
3. Hex 1 2 x 5 Long Bolt Hex 1 2 x 11 Long You May Have Extra Parts With This Model HARDWARE IDENTIFIER Item 26 4 Item 4 23 Item 16 4 Ve NY P Item 23 14 24 Item 7 12 Item 24 12 HARDWARE IDENTIFIER OF RAY jm O Item 27 12 Item 30 1 Item 32 2 Item 29 1 Om xm Item 42 2 Item 43 1 Item 38 4 Item 54 4 d Item 41 1 Item 55 2 Item 44 1 Item 60 1 Item 45 1 S Item 56 1 Item 62 2 Item 59 5 EE Rit t Item 61 1 Item 63 3 25 10 04 P N 21166904
4. dow of 51 Repeat for all other height markings P N 21166904 10 04 22 If the elevator is still difficult Jam Hex Nuts to operate verify that the valves located on the strut are fully depressed when the trigger is activated NOTE two people are required for this procedure Adjust exposed cable length located next to the trigger See Step 19 by using the jam hex nuts on the cable end Slide outer shroud to exposed valves The valves must be fully depressed so elevator can be adjusted smoothly and fully extended to lock the elevator Trigger released locking ia Trigger squeezed unlocking elevator 23 10 04 P N 21166904 Item Qty Part No Description 4 200573 12 265575 920880 203474 980835 200544 206340 220589 908066 201504 220586 200574 906835 200704 202459 202856 908061 908062 203274 901492 901490 203113 203100 203218 920263 201611 203232 200484 200323 201124 960043 220140 220569 N wort O1 gt Q N pot NN bh Geh Po 1 4 12 1 1 1 1 2 1 P N 21166904 10 04 J Bolt 1 2 13 x 24 Nut Hex 1 2 13 Mounting Plate Washer Flat 1 2 x 1 O D Pole Pole Cap Square Nylon Insert Lock Nut Hex 1 2 13 Cap Arm Support Insert Support Arm Label Height Marker Logo Label 15 x 1 3 4 Bolt Hex Flange 1 2 13 x 9 H Frame Washer 5 8 Nut Hex 1 2 Bolt Hex Head 1 2 13 x 4 Crossme
5. eginning with upper support arms 9 secure support arms to pole Continue by securing lower support arms 9 as shown P N 21166904 10 04 6 1 Secure H frame 13 to support arms 9 AWAR N G TWO PERSON REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE IMPORTANT Do not over tighten 7 10 04 P N 21166904 12 Install cross brace 17 with nuts 59 and bolts 22 as shown Repeat for opposite side P N 21166904 10 04 8 13 Install vertical supports 18 nuts 2 washers 4 and bolts 53 as shown IMPORTANT The end with the double holes need to be toward the playing surface 9 10 04 P N 21166904 DA Attach handle plates 21 to vertical supports 18 as shown Attach cable bracket 20 to handle plates 21 as shown SIDE VIEW P N 21166904 10 04 10 Remove tie strap that secures cable to strut assembly Slide shroud 36 46 over strut assembly 35 as shown CAUTION Do not depress valve stems Pressing strut valve stems will cause a rapid extension of the strut and possible injury 16 Mount activator bracket 47 to strut assembly 35 with hardware as shown CAUTION Do not depress valve stems Pressing strut valve stems will cause a rapid extension of the strut and possible
6. g plate on cement drainage hill Apply some pressure to level mounting plate on top of drainage hill Level mounting plate and square with playing surface Clean off any excess cement on mounting plate at this time PLAYING SURFACE NOTE Check leveling of mounting plate 3 several times while concrete is curing IMPORTANT Front of mounting plate 3 must be parallel with playing surface WARNING DO NOT PROCEED TO STEP 6 UNTIL CONCRETE HAS CURED FOR A MINIMUM OF 72 HOURS ALLOW ADDITIONAL TIME FOR COLD WET OR HUMID WEATHER P N 21166904 10 04 4 AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Upright pole 5 Assemble lower pole flange onto protruding J bolts 1 as shown The flange will then rest on the nuts 2 from Step 2 NOTE Orientation bracket must face playing surface IMPORTANT Holes in pole must be parallel with playing surface PLAYING SURFACE Secure pole 5 flange to mounting plate 3 as shown Tighten completely PLAYING SURFACE 5 10 04 P N 21166904 Insert caps 8 into end of each support arm 9 as shown Tap firmly in position AWAR N NG TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT Apply logo label 11 to lower support arms 9 as FOLLOWING RECOMMENDATION shown Repeat for opposite side MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE B
7. ing of any problems or to answer any questions please contact our Toll Free Customer Service Number listed below Service will be quicker if you have your Model Number found on carton and assembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE Toll Free Customer Service Number for U S 1 800 558 5234 Internet Address http www hydra rib com COPYRIGHT 2002 by HUFFY SPORTS 1 10 04 P N 21166904 IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the system See instruction manual for proper installation DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on pole When adjusting height keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc objects may entangle in net Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of co
8. mber Vertical Tube 5x 5 Foam Pad Cable Support Bracket Plate Handle Bolt Hex Flange 5 16 18 x 2 1 2 Nut Hex Flange 5 16 18 Washer Flat 5 16 x 7 8 O D Rim Orange Bolt Hex Flange 5 16 18 x 3 Washer 3 4 O D Spring Washer Large Flat Nut Hex Locking 3 8 16 Cover Plate Orange Screw Self Tapping 1 4 20 x 1 2 Label Logo Circle PARTS LIST 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 2 H RAMP P bi ch ch ch ch ch 204282 900429 201982 201512 200655 920262 920038 220065 203063 203017 203439 220064 201983 908064 901493 201501 201503 201502 201511 201981 203217 201531 203078 207388 201515 203220 201519 203664 240019 240027 206555 206251 201506 Net Strut Assembly Outer Shroud Label Height Adjustment Bolt Covers Bracket Orange Inner Bracket Black Bolt Carriage 3 8 x 5 1 2 Nut Hex Nylon Locking 3 8 Nut Hex 3 8 Bolt Hex 3 8 x 6 Spacer 5 x 1 2 O D Inner Shroud Actuator Plate Trigger Assembly Shepherd s Hook Height Strip Height Window Handle Spacer Bolt 1 2 13 x 12 Bolt 5 16 x 1 1 2 Bolt 5 16 x 3 4 Bolt 1 4 20 x 4 Double Sided Tape Bolt 3 8 16 x 11 Locknut 5 16 18 Nylon Screw 6 x 1 Slotted Hex Head Bolt Hex Head 5 16 18 x 5 1 2 Long Bolt Hex Head 1 4 20 x 3 4 Long Nut Hex Nylock 1 4 20 Pole Pad Bolt
9. rrosion excessive use or misuse could result in system failure If technical assistance is required contact Huffy Sports Minimum operational height is 6 6 1 98 m to the bottom of backboard This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 2 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as REQUIRED TOOLS AND pesticides herbicides or salts are all important MATERIALS Adult supervision is recommended when adjusting height Three People Serious injury could occur if teeth face come in contact with backboard net or rim Tape Measure Shovel and Post Hole Digger Concrete 1260 Ib 572 kg and Container to Mix Carpenter s Level Two Step Ladder 8 ft 2 4 m Wrenches Two 1 2 9 16 3 4 One 3 8 One 1 4 Flat Screwdriver Pliers For more information on assembly placement proper use and maintenance visit The American Basketball Council website at http www smarthoops com IMPORTANT Have any questions Don t go back to the store We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken occasionally problems may occur To ensure prompt and correct handl
10. rrosion rust pitting chipping and repaint with with exterior enamel paint If rust has penetrated through the steel anywhere replace the pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before using Check system before each use for instability Never play on damaged equipment Keep pole top covered with cap at all times HYDRA HiIB 1 800 558 5234 201255 2 99 HEIGHT ADJUSTMENT 1 Grasp handle and squeeze trigger 2 Move up or down to desired height 3 Release trigger at desired height 201512 06 02 P N 21166904 10 04 2 Ensure ground is level with playing surface then dig pole hole PLAYING AWARNING SURFACE BEFORE DIGGING GROUND SURFACE Install nut 2 to J bolt 1 as shown Repeat procedure for other three J bolts 1 IMPORTANT Make sure nuts are 2 5 08 cm from top of J Bolts Install threaded ends of J bolts 1 through holes in mounting plate 3 and secure as shown NOTE Make sure J bolts 1 are in the illustrated position NOTE Nuts on the top of plate are used for leveling the pole after system is fully assembled 3 10 04 P N 21166904 Fill hole with concrete Tamp down concrete to release air pockets and build drainage hill 8 Insert J bolts 1 from mounting plate 3 into cement as shown Move assembly around to release any air pockets in cement then rest mountin
11. t structure by inserting bolts 26 and washers 24 through top holes in bracket 39 Tighten nuts 23 completely Q2 Attach foam pad 19 to Backboard Attach bracket Insert inner bracket 40 into bracket 39 as shown Insert bolts 26 and washers 24 through top holes of inner bracket 40 as shown Now tighten backboard frame nuts 23 completely P N 21166904 10 04 16 24 Insert spacer 45 through rim assembly 25 Place rim assembly on bracket 39 so that carriage bolt 41 is inserted through hole on top of inner bracket 40 Install hex bolt 44 washers 27 and nut 42 through top holes on bracket 39 through spacer 45 as shown Tighten completely BOTTOM VIEW 5 Install spring 28 concave washer 29 and center lock nut 30 to carriage bolt 41 as shown Do not over tighten as rim will not flex properly See leveling instructions to determine how much to tighten nuts 42 and 30 17 10 04 P N 21166904 26 LEVELING INSTRUCTIONS Place level on rim 25 and adjust nut 42 until level Tighten nut 30 to set rim tension for LH playing DO C 5 Su we ww o py s RUM KEE aS Apply logo label 33 to cover plate 31 Install cover pla
12. te 31 on rim 25 using self tapping screws 32 as shown NOTE ORIENTATION OF COVER PLATE Secure net 34 to NOTE Official rim height is 10 3 05 m from top of rim to playing surface 10 feet 3 05 m P N 21166904 10 04 18 Check leveling at this time Pole should be level in all directions NOTE If adjustment is necessary adjust system by rotating the nuts 2 between mounting plate 3 and pole flange Referred to in Step 6 After system is leveled completely tighten nuts 7 above pole flange Apply height adjustment label 37 to front of pole as shown REGULATION RIM HEIGHT IS 10 FEET 3 05 m 19 10 04 P N 21166904 Attach hook 49 to height strip 50 as shown Attach this assembly to unit with bolt 12 and nut 7 as shown P N 21166904 10 04 20 as shown 57 Attach height window 51 to pole using four pieces of double sided tape E SN A X o T e o 9c 2 s Kei 10 04 P N 21166904 21 To install height marking labels 10 raise backboard so that the rim is 10 off the playing surface two people required for this procedure Remove 10 mark label from sheet and insert label on 50 through win
Download Pdf Manuals
Related Search