Sony UP-D77MD User's Manual
Contents
1. printer slowly pull it out to the right If the tray tray cover and or paper cover into the printer cover is in the way remove it a EZ a A 8 Press the gt button If the tray cover is in the way remove The error message disappears and the printer it by lifting it up and then pulling it returns to the standby status out to the direction of arrow O READY 3 Press PUSH on the paper tray A4 The paper tray pops out D Check whether any paper is found on the bottom of the printer If you find one remove it 6 Ensure that the paper is properly loaded Discard the sheets removed in steps 2 and 5 22 Troubleshooting Index A Accessories supplied 7 20 Assembly 7 Barcodes 10 Bottom cover 7 22 C Cleaning Cabinet 17 Filter 17 Thermal head 18 Color printing pack 19 Combination of ink ribbon and paper 19 Connections 8 E EJECT button 9 Error messages 21 F Fan 7 17 Features 5 Filter 7 17 Image data 12 Ink ribbon 9 Ink ribbon and paper usable printing pack 19 Ink ribbon cassette Barcodes 10 If your ink ribbon should tear 10 Loading 9 Notes on storing 10 Removing any slack 10 Start position marker 10 Ink ribbon holder 7 9 Introduction 5 L LAMINATE printing pack 19 Loading2. EJECT button The ink ribbon cassette pops out Never put your hand into the ink ribbon compartment The thermal head becomes very hot You may burn yourself if you touch it 3 Detach the used ink ribbon from the ink ribbon holder with the ink ribbon while pressing in the arrow direction Remove the other spool Before Printing 9 ma III uonesedo 4 Load the ink ribbon to ink ribbon holder Load the spool holding the ink ribbon into the right hand part of the holder while pressing in the arrow direction Ink ribbon holder supplied Fit the other spool into the left hand part of the holder Bar code 5 Remove any slack from the ink ribbon If the ribbon is left slack it may be crumpled and damaged when inserted Start position marker Wind the spool until the Start position marker faces upward 6 Insert the ink ribbon cassette firmly until it stops SONY mark faces forwards 1 0 Before Printing If your ink ribbon should tear Repair the tear with transparent tape There should be no problem with using the remaining portion of the ribbon Transparent tape Notes When storing ink ribbons e Avoid placing the ink ribbon in a location subject to high temperatures high humidity excessive dust direct sunlight e Store partially used ink ribbon in its original package Loading the Paper Load t
3. appears in the printer window display and the printer is in standby status While READY is displayed the printer is in standby mode READY The size of the paper A4 being loaded 2 Send the image data from the computer modality to the printer While the printer is receiving the image data from the computer the following message appears E Printing The printer starts printing and the following message appears NTIN Color indication changes LO as color printing proceeds Laminate printing Starting YELLOW gt MAGENTA CYAN gt LAMI Finishing The printing time depends on the size of image type of ribbon and or resolution mode It takes about 85 seconds A4 size paper for a printout to emerge from the paper outlet Once printing has been completed the printer returns to standby status READY A4 e Do not pull the paper out until the printer finishes printing e To prevent paper jamming do not allow more than 20 printouts on the paper cover If the printer does not print The printer will fail to print when an error message is displayed in the printer window display Take remedies according to explanation of the message given in Error Messages on page 21 Notes on storing your printouts e Avoid storing the printout in a location subject to high temperatures high humidity excessive dust and direct sunlight e Do not stick tape on a print
4. the printer widow display the filter of the ventilation holes on the left side has become dirty Precautions 1 7 ma III snosuel eosI y To clean the filter proceed as follows 1 Remove the fan cover then filter Filter Fan cover 2 Clean the filter using the vacuum cleaner and the like e Be careful that the filter will be caught in the cleaner e Do not rub the net of the filter strongly 3 Reset the filter and the fan cover on the side panel as they were Cleaning the thermal head You should clean the thermal head in the following cases e When the vertical white stripe appears on the printout e When the scratch appears on the printout How to use the white tip and black tip When using the white tip the sponge roller wipes off the dust on the thermal head When using the black tip the polishing material on the sponge roller scrapes off the dust on the head Use the white tip in the following cases e When a vertical white stripe appears on the printout because of dirt on the thermal head e Ordinary head cleaning for preventing accumulation of dirt on the head Precautions Use the black tip in the following cases e When a scratch appears only on the printout but no scratches appear on the spaces around the picture e When the use of the white tip has no effect e Periodic head cleaning We recommend use of the black tip every month or every 500 sheets of prin
5. Adjusting Printouts 00s 220000s00000000000000000000000 13 Adjusting Gray ssessssesseessserseessesssesssssssersssessees 13 Adjusting the Color sseeeeeeeerererrerereee 14 Miscellaneous Precautions cseccccccsccccccceseccesccescsceresssseseseeses 17 Safety a csedevesicccvstiasadhsasdbevspedans ened ao taa eain 17 Installati n vi rarna enn apai an ieaiai aida 17 On Transportation sesesssssssesseessssssrsssessrssssees 17 Cleaning NA W a A a A a 17 Ink Ribbon and paper ccsccccsssscccsssssccsssees 19 Specifications ex sowa doo owa 20 Troubleshooting 200s 00000 000000000000000000000000000000 21 Error MESS S ES ra wyd AAA 21 If the Paper Jams 3 459 dA 21 Lit 3 CO PREY 23 Introduction Features The UP D77MD DICOM Color Printer is a dye sublimation thermal transfer printer designed to reproduces image data in DICOM format sent via the network The UP D77MD has the following functions e Equipped with DICOM Digital Imaging and Communications in Medicine features The DICOM portion of the unit receives image data in DICOM format sent from the modality via the network processes them in A4 size paper either by enlarging or reducing them High quality and high print resolution The unit allows you to print out in full color 256 gradations process for each color and in high resolution print mode 300 dpi System Configuration The system allows you to make printouts o
6. NUI 26 IP Address When you use the unit for the first time immediately after you purchase the unit it is necessary to set up the DICOM part placed inside the unit adding an IP address and so on Before starting the setup confirm the following with the network administrator The IP address the UP D77MD will use on the network e Sub net mask of the network e Gateway address if a gateway is included in the network To confirm the IP address The IP address assigned to the UP D77MD can be confirmed 1 Tum the UP D77MD on 2 Press the MENU button 3 Display INFORMATION on the LCD by pressing the lt or gt button 4 Display IP ADDRESS on the LCD by pressing the 4 or button The IP address assigned to the UP D77MD appears on the LCD IP Address Setting up the Personal Computer to be Used for Setup Start the personal computer to be used for setup 2 Open the TCP IP setting page 3 Enter the IP address of the computer and the sub net mask IP address of the computer NNN NNN NNN nnn NNN NNN NNN NNN IP address assigned to the UP D77MD on the network nnn Arbitrary numbers from 1 to 254 should not be the same as those of the fourth NNN of the UP D77MD IP address Sub net Mask 255 255 255 0 R Restart the personal computer 82 Connect the UP D77MD and the personal computer to be used for setup using the network cross cable About the Setup Window The UP D77MD can be set
7. Send To From text box Send to text box Enter addresses in the corresponding text boxes Enter item Content Mail Server IP IP address of the mail server Address User ID User ID From Return address of the E mail notification when an error occurs and an e mail message is sent Send to Destination address of the E mail a Use only numerical characters for the IP address Click the Save settings button The settings are saved Confirmation After Setup After all of settings have been completed Turn off the power of the UP D77MD and disconnect the UP D77MD and the personal computer for setup Proceed as follows to confirm the operation of the UP D77MD 1 Connect the UP D77MD to the network 2 Tumon the power of the UP D77MD 3 Insert a paper tray in which the paper has been placed and the ink ribbon cassette 4 Send the image data from a modality The unit starts printing When the image data is not sent Check whether or not the IP address of the modality side is correct When setting up an E mail Confirm the settings for an E mail as follows Click E mail settings in the page selection area to open the E mail settings page When this page is opened after E mail settings have been completed the Send a test E Mail button appears 2 Click the Send a test E Mail button A test e mail message is sent if settings have been correctly performed SONY This paige
8. Version Number Media Type Media Size Pixel Matrix Resolution Maximum Density Minimum Density Displays various information on the unit status Film Paper Remaining Unknown is always displayed in case of the UP D77MD Refresh button Click this button to update the window E Mail Settings Page This page allows you to perform settings related to E mail 1 2 Station 3 Errors events to monitor setting area Sets the criteria for sending the E mail Mail Server and Address setting area Performs the setup of E mail service Send a test E Mail button Press this button to send an E mail message for testing purposes Save settings button Click this button to save the settings performed on this page If you move to another page without pushing this button the settings will be lost About the Setup Window 29 m III dnyas Setup of the Unit Perform the following settings when the unit is used for the first time after being purchased or when the IP address assigned to the UP D77MD is changed 1 Open the DICOM Settings page For detailed information on how to open the page see Opening the Setup Window on page 27 2 Perform the required settings related to TCP IP IP Address text box Sub net Mask text box Default Gateway text box Enter the IP address of the UP D77MD on the network in the IP Address text box Enter the sub net mask in
9. allows you to setup E Mail settings and errors to monitor Errors events to monitor F Motor Sensor error z Film Jamming More than 30080 printed with the E Mail wil be posted when the selec cur Mail Server and Address eee iasant com Send a test E Mail button Confirmation After Setup 31 a WANA Sony Corporation http www sony net
10. can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules For the customers in Canada This unit has been certified according to Standard CSA C22 2 No 601 1 For the customers in the U S A and Canada Model UP D77MD is Non Patient Equipment This unit can not be used in the vicinity of patients Patient Vicinity When you use this product connected to 240 V single phase be sure to connect this product to a center tapped circuit Important safeguards notices for use in the medical environments 1 All the equipments connected to this unit shall be certified according to Standard IEC60601 1 IEC60950 1 IEC60065 or other IEC ISO Standards applicable to the equipments 2 When this unit is used together with other equipment in the patient area the equipment shall be either powered by an isolation transformer or connected via an additio
11. the paper 10 M Mounting paper tray and cover 7 P Paper adding paper 11 If paper jams 21 Loading 10 Paper cover 7 Paper jams 21 Paper outlet 12 Paper tray 7 10 11 Part Names and Functions Front 6 Rear 6 Picture size 20 Power requirements 20 Precautions Condensation 17 Installation 17 Safety 17 Transportation 17 Print paper Notes on storing 11 Printer window display 12 Printing 12 If the printer does not print 12 Printing pack 19 Printing time 20 Printouts 12 Notes on storing 12 R Ribbon and paper 19 Ribbon door 9 S SOP and Meta SOP classes 20 Specifications 20 Standby status 12 Start position marker 10 Supplied accessories 7 Bottom cover 7 CD ROM 7 Fan cover 7 ferrite cores 8 Ink ribbon holder 7 Paper cover 7 Paper tray 7 System configuration 5 T Troubleshooting 21 Index 23 ma INNI Setup Manual Table of Contents Preparation OVETVIEW saccsccissiscssvescessseassecanesenbscssesosessocsesacccnseones 25 Rediiiremen S u OE WE 25 IP Address 3 3 seeds 0005 PSE soosoo stos 26 Setup Setting up the Personal Computer to be Used for SOLU cncsssvossnssassvecssecssennssisecesusessnsessvessssatensedeseesesseine 27 About the Setup Window 0 cccsssscccsssrceesees 27 Opening the Setup Window secsec 27 Components of Pages enesenn 28 Setup of the Unit cssscccssscsssccsssesssescsseseeees 30 Setup of E Mail 2 0s 00s0000000000000000000000000000000 3
12. up on the setup window displayed on the Web browser of the personal computer to be used for setup The setup window has the following pages e Summary Print Job page Displays the summary and print job status of the UP D77MD e DICOM Settings page Sets up the IP address DICOM AE title and so on e Printer Status page Displays the status of the UP D77MD e E Mail Settings page Sets up the items related to E Mail Opening the Setup Window Start the personal computer to be used for setup and then start the Web browser software 2 Enter the following address http NNN NNN NNN NNN This is the IP address assigned to the UP D77MD on the network Page selection area DICO allows you to setup IP ies ess a rd DICOM AF EG ofthe pri M s 5 TCP IP fise tes 1 100 255 255 255 0 Default Gateway ie optional and can be left blank if it does not exst in the rk 3 Click the desired page in the page selection area The desired page opens Setting up the Personal Computer to be Used for Setup About the Setup Window 27 a III dnies 28 Components of Pages Summary Print Job Page This page displays information on the UP D77MD Summary Print Jc To refresh information displayed pi ss Refresh A butte t the botti FilmStation R NAE Primary Printer 1 Printer printer status display section Printer Status Displays the printer status Pap
13. use the following power supply cord With connectors plug or female and cord types other than those indicated in this table use the power supply cord that is approved for use in your area United States Canada Plug Type HOSPITAL GRADE HOSPITAL GRADE Female end E62405 E35708 LR53182 LL022442 LL088408 Cord type E159216 E35496 LL112007 1 LL20262 Min Type SJT LL32121 LL84494 Min 18 AWG Min Type SJT Min 18AWG Minimum cord set 10A 125V 10A 125V rating Safety approval UL Listed CSA Note Grounding reliability can only be achieved when the equip ment is connected to an equivalent receptacle marked Hospital Only or Hospital Grade For Customers in Taiwan only Ress as 3 Instructions for Use Table of Contents Introduction Features inssin eoio soes rasan Ne esk So resns 5 System Configuration cccscccsssssccssssscsssssseeees 5 Location and Function of Parts and Controls 6 GOI ZO R 6 Reat innen ae GS Mae ee 6 Preparation Supplied Accessories sscssscccssscsssssssssscsssccssees 7 Assembly weed dada AOC 7 Connections 202 2000 20000000000eoooooooeeo ooo eooooeeooow 0000000 8 Operation Before Printing 3 d 9 Loading an Ink Ribbon Cassette 9 Loading the Paper seeen 10 PRUNING wa e zoo odd Cza wd Ewy Eizo GEE a 12 Starting t PUNi nissene A 12 Making Printouts with the Desired Color 12
14. 0 Confirmation After Setup cccsscsssscssseeeees 31 Overview This setup manual gives the system administrator information needed to setup the unit on the network or to reset the IP address and so on This setup manual describes the preparation for the setup gives an overview of the setup window explains how to perform setup related to IP address and so on and explains how to setup an E mail warning to tell automatically when any trouble occurs Requirements The following hardware and Web browser software are necessary to perform the setup Computer A computer which can be connected to the network connector of the UP D77MD Operating system 0 Microsoft Windows 95 Windows 98 Windows NT 4 0 Windows 2000 or Windows XP LAN cable 100BASE TX cross cable Web browser software Internet Explorer a 5 5 or later or Netscape d 4 or later Set the Web browser software as follows No proxy A blank page is opened when the Web browser software is started a Microsoft Windows Windows NT and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and or in other countries Netscape and Netscape Navigator are registered trademarks of Netscape Communications Corporation in the United States and or in other countries Other system names and product names mentioned in this manual are also trademarks and registered trademarks Overview Requirements 25 a III UONEJEdBJd
15. AIT The printer is carrying out processing in the printer to ON which requires time window display gt Set the POWER switch of the printer to Wait for a while CNA F RASA a ON REMOVE The paper has jammed wad 7 Sa doki agam PAPER AND Remove jammed paper from the printer page 6 PRESS gt and press gt button page 21 ssc eae ai not b ao 8 RIBBON The ink ribbon develops some trouble ake connections correctly page 8 ERROR Ensure that the ink ribbon does not tear The printer does An error message appears on the printer and the ink ribbon cassette and paper not print window display tray are loaded properly pages 7 9 and Take remedies according to Error 10 Messages page 21 Check that the currently used printing An ink ribbon cassette and paper are not aan KM PR loaded pag Load an ink ribbon cassette and paper MECHA The mechanical trouble occurs in the pages 9 and 10 TROUBLE printer Error Messages If a problem occurs the ALARM indicator lights and an error message stating the problem appears in the printer window display Note the message and perform whatever action is necessary to solve the problem Error Possible causes and remedies messages END OF The ink ribbon has been completely used RIBBON Replace with the new ink ribbon Ink ribbons cannot be reused page 9 HEAD IN The thermal head has overheated COOLING Leave the printer until the head cool
16. SONY 2 653 913 13 1 DICOM Color Printer Instructions for Use Page 2 Setup Manual Page 24 This manual is comprised of the Instructions for Use and the Setup Manual The Instructions for Use gives the information on how to use the printer for the routine work The Setup Manual gives the system administrator the information needed to setup the printer and connect it to the network CE UP D77MD 2005 Sony Corporation 2 Owner s Record The model and serial numbers are located at the rear Record these numbers in the space provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No Serial No To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only THIS APPARATUS MUST BE EARTHED To disconnect the main power unplug the AC IN connector This symbol indicates the equipotential terminal which brings the various parts of a system to the same potential For the customers in the U S A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and
17. able After you finish with them replace them with new ones Ink Ribbon and paper 19 ma III snosuel eoSI y Specifications Power requirements 100 240 V AC 50 60Hz Input current 35 A to 1 5 A Operating temperature 10 C to 30 C 50 F to 86 F Operating humidity 20 to 80 no condensation allowed Storage and transport temperature 20 C to 60 C 4 F to 140 F Storage and transport humidity 20 to 90 no condensation allowed Dimensions Approx 493 8 x 176 x 468 8 mm w h d 19 2x 7 x 18 inches Mass Approx 21 kg 46 Ib 5 Oz Printing system Dye transfer sublimation thermal printing Thermal head 2 560 elements 11 8 dot mm 300dpi Gradations 256 levels each for yellow magenta and cyan Picture size Maximum Letter size 254 0 x 203 2 mm w h 10 x 8 inches A4 size 271 6 x 203 2 mm w h 10 x 8 inches Picture elements Maximum Letter size 3 000 x 2 400 dots w h A4 size 3 208 x 2 400 dots w h Printing time Approx 85 seconds per page A4 size Digital interface Network port x 1 RJ 45 Modular jack Conforming to 100BASE TX standard Accessories supplied Ink ribbon holder 1 Paper tray 1 Paper cover 1 Fan cover 1 Bottom cover 1 Ferrite core 2 Thermal Head Cleaning Kit 1 CD ROM 1 Before Using this Printer 1 Optional accessories Self Laminating Color Printing Pack UPC 770 Self Laminating Color Printing Pack UPC 771 Medical Specifications Protec
18. cool dark location To subsequently use the printing pack place it in its sealed package in a warm room for several hours Doing so prevents condensation from forming when the printing pack is removed from its package On Transportation Do not transport the printer with the supplied accessories Doing so may cause malfunction T Remove the ink ribbon cassette and the paper tray 2 Lock the thermal head Turn on the power of the printer Press the MENU lt and gt buttons together and hold them for 2 seconds Turn off the power of the printer Never put your hand into the ink ribbon compartment when locking the thermal head Doing so may cause injury to your hand because it may be caught by the thermal head To unlock the thermal head Turn on the power of the printer again The thermal head moves and you can load the ink ribbon cassette again Cleaning Be sure to turn off the power of the printer before cleaning it The ink ribbon and paper roll removed When the cabinet becomes dirty Clean the cabinet panel and controls with a soft dry cloth or a soft cloth lightly moistened with a mild detergent solution Do not use any type of solvent such as alcohol or benzine or chemical cloth which may damage the finish Cleaning the filter Ventilation holes are provided to prevent the unit from overheating on the both sides and the rear of the printer When the message CLEAN FAN FILTER appears on
19. d the printer operates according to the modified data In such a case the modified data remains effective until another user set is loaded even if you turn off the power Adjusting Gray Makea printout of image data which has a large amount of gray parts It is recommended that you make a printout of the full size picture If you make a printout composed of multiple reduced images it may be difficult to check the color If you are satisfied with the gray in that printout go to Adjusting the Color on page 14 If you wish to adjust the gray further proceed as follows 2 Press the MENU button INFORMATION appears ACZ 3 Press the gt button COLOR ADJUST appears ADJUST gt Adjusting Printouts 13 ma III uonesedo 4 Adjust the gray When you adjust the gray the color intensity is also adjusted However adjust the gray first then adjust the desired color GE i oe et ja ja ah aw x SHARPNESS z az Xo lt o lt Select the item for adjustment by using the 4 or v button V Scrolls up to the next item 4 Scrolls down to the previous item Adjust the level by pressing the lt or gt button You can adjust the color level for CYN RED MAG GRN YEL BLU DARK and LIGHT for the tone aad GAMMA for the half tone between 32 to 32 The value 0 is the standard level gt Increases the lev
20. d in a package sheets of paper If you exceed this limit paper jams may occur Also do not place different types of paper in the tray If you do paper jams may occur If you load the paper that is not compatible with the ink ribbon used the gray balance may be changed Load the paper so that it lays flat in the paper tray If the paper is curled it will overflow the paper tray and the printing position may shift If this happens load fewer sheets in the paper tray 3 Close the tray cover and slide the paper tray into the printer until it clicks into place Notes on storing paper e Avoid storing the paper in a location subject to high temperatures high humidity excessive dust direct sunlight e Use the original package for storing unused paper Before Printing 11 2 III Printing Before printing e Ensure that the printer is properly connected page 8 e Ensure that the combination of the ink ribbon and paper is correct pages 9 and 10 e Ensure that the ink ribbon cassette and paper are properly loaded page 19 e Ensure that the desired color is loaded page 12 Starting to Print uonesedo Printer window display 1 Paper outlet Tum onthe power of the printer While the printer is starting up INITIALIZING is displayed After about two minutes the following message
21. detailed information refer to Setup Manual provided in the latter part of this manual and also consult the system administrator e Before connecting the unit using a 1I00BASE TX cable attach the ferrite cores provided to both ends of the cable for noise prevention For detailed information on how to attach the ferrite cores see How to attach the ferrite cores on page 8 100BASE TX cable Power cord to the LAN a Be sure to use a network cable of less than 30 m in length and rated more than category 5 How to attach the ferrite cores Before using the unit attach the supplied ferrite cores for noise prevention To confirm to radiation standards attach the supplied ferrite cores to both ends of the cable 8 Connections Ferrite core Stoppers About 13 mm 1 2 inch About 13 mm 1 2 inch T Release the two stoppers to open the ferrite core 2 Makea loop at the end of the cable about 13 mm 1 2 inch away from the connector and then attach the ferrite cores 3 Close the ferrite core until it clicks Before Printing This section describes the operations that must be performed prior to starting printing This explanation assumes that the printer has already been installed and that all connections have been made e Loading an ink ribbon cassette on this page Loading the paper page 10 Once these operations have been completed
22. e and level shown on the menu or scroll up and down through a menu MENU button 13 Press this button to display or close the printout adjust menu in the printer window display EXEC button 13 Use this button in menu operation Location and Function of Parts and Controls 9 Paper cover 7 Printouts are ejected here Paper tray 7 10 Load paper here Press the point marked with PUSH to remove the paper tray Rear 1 Network connector RJ 45 modular jack 8 Conforms to the LOOBASE TX standard Used to connect to the LAN When using a LAN cable CAUTION For safety do not connect to the connector for peripheral device wiring that might have excessive voltage Y Equipotential ground terminal connector Used to connect to a ground equipotential plug to bring the various parts of the system to the same potential Refer to Important safeguards notices for use in the medical environments on page 2 NAC IN connector 8 Use a proper power cord for your local power supply not supplied Refer to Warning on power connection on page 3 and Warning on power connection for medical use on page 3 Supplied Accessories This printer is packed together with the following accessories Check that nothing is missing from your package Paper tray 1 Paper cover 1 N Bottom cover 1 Ink ribbon holder 1 Thermal Head Cleani
23. el lt Decreases the level When you keep the button pressed the number changes quickly To adjust the color intensity RED GREEN BLUE Item tobe Adjustment Button to be adjusted pressed CYN RED To make an image reddish To make an image lt cyan MAG GRN To make an image greenish To make an image lt magenta pink YEL BLU To make an image bluish To make an image lt yellowish To adjust the contrast Item to be Adjustment adjusted DARK To adjust the dark area of an image LIGHT To adjust the light area of an image Adjusting Printouts To adjust the tone density gradation Item to be Adjustment adjusted GAMMA To adjust the half tone of printouts To adjust the sharpness Item to be Adjustment adjusted SHARPNESS To adjust the sharpness of printouts The sharpness can be adjusted between O to 3 Example To set CYN RED to 20 toward RED Press the gt button until 20 appears When you keep the button pressed the number changes quickly Press the 5 gt button until 20 appears CE After finishing the adjustment of and press the MENU button to exit the adjustment mode Make a printout again Repeat your adjustments until the desired gray level is obtained When the desired gray is obtained go to the next color adjustment Adjusting the Color After finishing the gray continue adjustment for
24. er Displays the type of paper in use A4 Displays the size of the paper in use A4 is always displayed when either A4 size paper or letter size paper is used in the UP D77MD 2 Printer Job List display section Displays when a job is waiting to be printed 3 Add test pattern film to print job Push this button to print the test pattern 4 Refresh button Click this button to update the window About the Setup Window DICOM Settings Page This page allows you to set up the IP address and DICOM AE title 1 DICOM Settings This page allows you to setup IP address and DIG M AE title s of the printers TCP IP TCP IP section Setup Software Version Displays the version of the setup window IP Address Sets the IP address and displays it Sub net Mask Sets the Sub net mask and displays it Default Gateway Sets the default gateway and displays it Printer section DICOM Software Version Displays the version of the DICOM software DICOM Software Serial Displays the serial number of the DICOM software AE Title Sets the AE title and displays it Port ID Displays the port number Status Displays the status of the DICOM software Communication Log Keeps a communication log if a checkmark is placed here Save settings button Click this button to save the settings performed on this page If you move to another page without pushing this butto
25. f a foreign body falls into the cabinet disconnect the power immediately and consult your Sony service facility or your Sony dealer Installation e Avoid placing the unit in a location subject to mechanical vibration high humidity excessive dust direct or excessive sunlight extremely high or low temperatures e Ventilation holes are provided on the both sides and the rear of the unit to prevent the unit from overheating Be careful not to obstruct them with other objects or by covering the unit with a cloth etc On condensation If the printer is subjected to wide and sudden changes in temperature such as when it is moved from a cold room to a warm room or when it is left in a room with a heater that tends to produce quantities of moisture condensation may form inside the printer In such cases the printer will probably not work properly and may even develop a fault if you persist in using it If moisture condensation forms turn off the power and leave the printer standing for at least one hour If the printing pack is subjected to wide and sudden changes in temperature condensation may form on the ink ribbon or paper inside This will cause the printer to malfunction Also if the printing pack is used in this state spots are likely to appear on the printout To store a half used printing pack replace it in its original packing and reseal the package If possible keep the sealed printing pack in a
26. f the data in DICOM format sent from image diagnosis equipment such as CTs NMs The following shows a system configuration example Personal computer for managing the system DICOM server _ i DICOM LAN network Modality Image diagnosis equipment and so on N D Modality Image diagnosis equipment and so on i C egs00 lt lt o UP D77MD Features System Configuration 5 e III uononpoau III 6 Location and Function of Parts and Controls For details refer to the pages indicated in parentheses Front r w OPOWER switch Press to turn the printer on or off Fan cover 7 18 Provided to prevent the printer from dust Ribbon door 9 Pull the tab marked with PULL on the top on the ribbon door to open it when loading an ink ribbon cassette Printer window display 12 Displays the status messages In menu operation menu items are displayed If an error occurs a corresponding error message is displayed ALARM indicator 21 Lights in orange when the ink ribbon or paper is exhausted the paper jams or another problem occurs Cursor control buttons 13 Use these buttons to increase or decrease a valu
27. he paper by the following procedure Be careful not to touch the printing surface of the paper When loading the paper do not turn off the power Ifyou turn off the power the image data stored in the memory will be lost T Press PUSH on the paper tray The paper tray is ejected Remove the printing surface protection sheet if any Paper tray 2 Open the tray cover and place the paper in the paper tray Be sure to set the spacer according to the size of the paper before placing the paper in the paper tray Reverse side with printed logos Print surface protection Riffle the paper sheet Place the paper in the paper tray with the printing surface shiny side with no legends and its protection sheet facing When using the UPC 770 A4 size Pull up the tab bring the spacer to the A4 position and then push the tab down there When using the UPC 771 letter size Pull up the tab bring the spacer to the LETTER position and then push the tab down there The number of the paper is the same as the number of the paper that one roll of the ink ribbon can afford Usually the ink ribbon and paper have run out at the same time However even when either the ink ribbon or the paper has run out replace both the ink ribbon and the paper with new ones When you load the paper pay attentions to the following e The paper tray holds up to the total number of sheets containe
28. ired user number is displayed SAVE USER 3 EX Q Press the EXEC button All values adjusted in Adjusting Gray on page 13 and here Adjusting the Color are registered in the user set number selected in step The printer operates according to this registered value set unless you load another user set Also if you modify the settings the modified values remain effective until another user set is loaded even if you turn off the power 1 1 Press the MENU button to exit menu mode for adjusting gray and color The printer returns to standby status and READY appears in the printer window display Adjusting Printouts Miscellaneous Precautions Safety Operate the printer using the power source specified in Specifications page 20 Be careful not to damage the power cable by placing or dropping heavy objects on it it is dangerous to use the unit with a damaged power cable If you do not intend to use the unit for a long time disconnect the power cable Unplug the power cable by grasping the plug not the cable itself Do not disassemble the unit There is a danger of electric shock from the internal parts Be careful not to spill water or other liquids on the unit or to allow combustible or metallic material to enter the cabinet If used with foreign matter in the cabinet the unit is liable to fail or present a risk of fire or electric shock If the unit malfunctions or i
29. n the settings will be lost The Secondary Printer optional section is not used currently Printer Status Page This page displays the status of the UP D77MD 1 Printer Status display area Motor Sensor Displays the error status or the motor sensor system Film Paper Path Displays whether of not the paper has jammed in the printing path Film Paper Tray OK is always displayed in case of UP D77MD Films Papers Displays whether or not paper is loaded on the paper tray If the paper tray is not loaded Error is displayed Film Paper Output OK is always displayed in case of the UP D77MD Ribbon Cassette Displays whether or not the ink ribbon cassette is loaded Ribbon Displays whether or not the ink ribbon remains Paper Ribbon Pair OK is always displayed in case of the UP D77MD Paper Loading OK is always displayed in case of the UP D77MD Ribbon Status Displays whether or not the correct ink ribbon is loaded Printer Engine Status Displays the printer operating status idling printing and so on 2 Printer Statistics display area Displays the total printings performed by the unit Print count with the current thermal head Displays the total prints after the thermal head has been replaced Lifetime print count Displays the total prints since the unit has been shipped 4 Printer Media Information display area Vendor ID Model Name
30. nal protective earth terminal to system ground unless it is certified according to Standard IEC60601 1 Patient Area 3 The leakage current could increase when connected to other equipment 4 This equipment generates uses and can radiate radio frequency energy If it is not installed and used in accordance with the instruction manual it may cause interference to other equipment If this unit causes interference which can be determined by unplugging the power cord from the unit try these measures Relocate the unit with respect to the susceptible equipment Plug this unit and the susceptible equipment into different branch circuit Consult your dealer According to standard EN60601 1 2 and CISPR11 Class B Group 1 Caution When you dispose of the unit or accessories you must obey the law in the relative area or country and the regulation in the relative hospital Warning on power connection Use a proper power cord for your local power supply 1 Use the approved Power Cord 3 core mains lead Appliance Connector Plug with earthing contacts that conforms to the safety regulations of each country if applicable 2 Use the Power Cord 3 core mains lead Appliance Connector Plug conforming to the proper ratings Voltage Ampere If you have questions on the use of the above Power Cord Appliance Connector Plug please consult a qualified service personnel Warning on power connection for medical use Please
31. ng Kit 1 Ferrite core 2 CD ROM 1 Before Using this Printer 1 Retain the original carton and packing materials in case you have to transport this unit in the future Assembly Mount the supplied ink ribbon holder paper tray paper cover bottom cover and fan cover You cannot mount the ink ribbon holder when the thermal head is locked Before assembling turn on the power of the printer The thermal head is unlocked and you can mount the ink ribbon holder page 9 Fan cover with a filter Ink ribbon holder Paper tray Note on using the UP D77MD The unit is equipped with a hard disk which is used as the system region and for temporarily storing the image data The hard disk is susceptible to shock vibration and so on Pay attention to the following when using the unit Do not subject the printer to shock Do not use the printer in a place that vibrates or is unstable Do not move the printer while it is turned on Do not turn the printer off while printing Do not subject the printer to wide or sudden changes in temperature Note that the UP D77MD may not be able to start if the hard disk is damaged for some reason Supplied Accessories Assembly 7 a III UONEJEdGJd NI Connections Connect the unit to the IOOBASE TX LAN e Connect the AC power cord last e Before connecting to the LAN be sure to set up the required IP address and sub net mask For
32. out Also avoid leaving a plastic eraser on a printout or placing a printout in contact with materials which contain plasticizer under a desk mat for example e Do not allow alcohol or other volatile organic solvents to come into contact with the printouts Making Printouts with the Desired Color You can register the desired color of printouts as a user setting The printer allows you to register up to 9 sets of settings By selecting a desired user set number you can make printouts in the desired color 415 Printer window display 1 Press the MENU button INFORMATION appears ORNE 2 Press the gt button COLOR ADJUST appears ADJUST gt J 3 Press the button LOAD USER X appears LOAD USER 1 EXEC 4 Select the desired user preset number by pressing the lt or gt button z Display the desired LOAD USER 3 Pres mumie EXEC pressing the or gt button 5 Press the EXEC button The user setting selected in step 4 is loaded Adjusting Printouts You can adjust the gray first then you can adjust colors based on the adjusted gray You can store up to 9 color settings as a user set The printer retains these settings even if you turn off the power Thus different operators can make printouts with different color settings by loading the appropriate user set If the data of the loaded user set is modifie
33. s down and this message disappears HEAD IN The thermal head is warming up HEATING Leave the printer until the head has warmed up and this message disappears NO RIBBON Ink ribbon cassette is not fitted properly Ensure that the ink ribbon is loaded properly in the ink ribbon holder and the ink ribbon cassette in the printer page 9 NO IMAGE No image data for the patch print is stored DATA in the printer memory Transfer the image data from your computer to make a printout before making a patch print by pressing the EXEC button in the adjustment mode page 14 Turn off the power once and then turn it on If the message will still remain in the printer window display turn off the power immediately and contact your Sony dealer If the Paper Jams If the paper jams printing stops and the error message stating REMOVE PAPER AND PRESS appears on the printer window display Follow the steps below to remove the jammed paper 1 Remove the paper cover If any printouts have been ejected on the paper cover remove them first before removing the paper cover Check where any paper is jammed inside the printer If you find a jammed sheet around the paper outlet slowly pull it out starlight to the right Troubleshooting 2 1 ma III snosuel eosi If you find a jammed sheet on the way inside the T Re insert the removed bottom cover paper tray
34. splay ADVANCED by pressing the 4 or Y button ADVANCED re Display STANDARD by pressing the gt button ae el Adjust the hue saturation and value of the color Select the item to be adjusted by using the 4 or v button V Scrolls up to the next item 4 Scrolls down to the previous item Adjust the level by pressing the lt or gt button You can adjust each item between 32 to 32 The value O is the standard level Item to be Adjustment adjusted HUE To adjust the hue of the color SATURATION To adjust the saturation of the color VALUE To adjust the value of the color After adjusting the hue saturation and value of the color press the MENU button to exit the adjustment mode and make a printout to confirm the results of the adjustment When you are not satisfied with the results Reset the printer to menu mode again following the procedure in steps 2 and 3 in Adjusting Gray on page 13 The printer retains those adjusted values even if you turn off the power Proceed as follows to save them as a user set 10 store the adjusted values of the color as a user set Adjusting Printouts 15 ma III uonesedo 16 In menu mode display SAVE USER X by pressing the 4 or Y button PE USER 1 EXEC Q Display the desired user set number by pressing the lt or gt button Keep pressing the lt or gt button until the des
35. t the inserting pulling out of the holder about three times Open window Thermal head cleaning is finished 4 Remove the cleaning tip holder from the printer and remount the ink ribbon cassette in the printer Don t moisten the tip with the cleaning liquid or water A moistened tip may deteriorate the performance of the thermal head Especially when using the black tip be careful not to insert pull out the holder too many times at one cleaning The lifespan of the head may be decreased Be careful not to swallow the cleaning tips Store them out of the reach of children Ink Ribbon and paper You need paper and ink ribbon cassette for printing Ink ribbon cassette stands for the supplied ink ribbon holder loaded with ink ribbon Use the ink ribbon and paper contained in the same package If the printer detects an incompatible combination an error message appears in the printer window display and you cannot make printouts Self laminating Color Printing Pack UPC 770 Contains an ink ribbon and paper for automatic laminate coating Color ink ribbon 1 roll A4 size paper 72 sheets Self laminating Color Printing Pack UPC 771 Contains an ink ribbon and paper for automatic laminate coating Color ink ribbon 1 roll Letter size paper 72 sheets e Use only ink ribbon and paper for this printer If you use a different type the printer may not print properly or malfunction e Ink ribbon and paper are not reus
36. the color Before starting the color adjustment make a full size printout of the image which has the color you want to adjust 1 4 5 7 8 9 10 9 11 Printer window display J Display PRINT PATCH by pressing the 4 or Y button in menu mode PRINT PATCH U freon Press the EXEC button 25 identical images of the image last printed are printed on a sheet of paper as a patch print Each image has a different color balance but they have the same gray DD ZSZ CO ZK MIEJ Image whose gray and color adjusted in Adjusting Gray on page 13 Select the image which has the best color balance among the 25 images by looking at the printout Display SEL PATCH by pressing the 4 or Y button SEL PATCH gt lt m O Display the number selected in step 3 by pressing the lt or gt button Keep pressing the lt or 1 5 _ gt button until the A number selected in step XEC 3 is displayed Press the EXEC button The color is determined according to the patch number selected in step 3 However the gray adjusted in Adjusting Gray on page 13 is not changed a PATCH When you are satisfied with the color balance selected in step 3 go to step 10 If you are not satisfied with the color and want to adjust the hue saturation and value of the color go to the next step Di
37. the Sub net Mask text box Enter the IP address of the default gateway if a gateway is used on the network 3 Enter the DICOM AB title in the AE Title text box Up to 16 characters can be entered DICOM AE text box Primary Printe 4 Click the Save settings button The settings are saved 30 Setup of the Unit Setup of E Mail Setup of E Mail The E Mail settings page allows you to set up E mail service so that an e mail message will be sent automatically when an error occurs in the UP D77MD 1 Open the E Mail settings page For detailed information on how to open the page see Opening the Setup Window on page 27 2 Set criteria determining when an e mail message should be sent Motoy sensor error check box Errors events to monitor Film Paper Jamming check box More than 30 000 printed with the current thermal head check box Place the check marks on the check box corresponding to an error that requires notification via an e mail message Error item Content Motor Sensor error When an error occurs in the motor sensor system Film Paper When a paper has jammed Jamming More than 30 000 When the total number of prints with the current thermal head exceeds 30 000 printed with the current thermal head Perform the settings related to e mail Mail Server IP Address text box User ID text box Mil Server and Address Mel Server IP Address User From
38. there should be no need to perform them again during routine printing e When replacing the ink ribbon or paper do not turn off the power Turning off the power will cause the image stored in the memory to be lost Use the ink ribbon suitable for the type of print material Before attempting to load an ink ribbon make sure that the combination of the ribbon and paper is compatible See Ink Ribbon and paper on page 19 Use only ink ribbon and paper designed for use with this printer Failing to do so is likely to result in unsatisfactory printing or malfunctions See Ink Ribbon and paper on page 19 Loading an Ink Ribbon Cassette Load the ink ribbon to the supplied ink ribbon holder and load the ink ribbon cassette referring to the ink ribbon holder loaded with the ink ribbon to the printer s ribbon compartment e When you use the printer at the first time the thermal head was locked at the factory Turn on the printer first to unlock the thermal head then start to load an ink ribbon cassette Once an ink ribbon has been completely used replace it Ink ribbons are not reusable Do not rewind the ink ribbon for reuse Do not touch the ink ribbon or place it in a dusty location Finger prints or dust on ink ribbon will result in imperfect printing 1 Open the ribbon door by pulling the tab on the ribbon door and marked with PULL 2 Remove the ink ribbon cassette by pressing the
39. tion against electric shock Class I Specifications Protection against harmful ingress of water Ordinary Degree of safety in the presence of flammable anesthetics or oxygen Not suitable for use in the presence of flammable anesthetics or oxygen Mode of operation Continuous Design and specifications are subject to change without notice SOP and Meta SOP Classes SOP Class Name SOP Class UID Verification SOP Class 1 2 840 10008 1 1 Basic Color Print Management Meta 1 2 840 10008 5 1 1 18 SOP Class Basic Film Session SOP Class 1 2 840 10008 5 1 1 1 Basic Film Box SOP Class 1 2 840 10008 5 1 1 2 Basic Color Image Box SOP 1 2 840 10008 5 1 1 4 1 Class Print SOP Class 1 2 840 10008 5 1 1 16 Basic Annotation Box SOP Class 1 2 840 10008 5 1 1 15 Error Possible causes and remedies Troubleshooting messages NO PAPER e The paper has run out If a problem appears check the following trouble Load the paper into the paper tray shooting guide first and perform whatever action is page 10 The spacer of the paper tray is not set necessary to solve the problem If the problem persists correctly turn off the printer and consult with your Sony dealer Set the spacer to the correct position according to the size of the currently Symptom Possible causes and remedies used printing pack page 11 Nothing appears The POWER switch of the printer is not set PLEASE W
40. tout to keep the thermal head clean Store the tips by inserting the white one into the cleaning tip hole on the holder and the black one into the spare tip hole Cleaning tip hole Spare tip hole Attaching the tips on the cleaning kit holder 1 Align the pronged parts of the tip with the cross notches of the hole Cross notches Pronged parts 2 Insert the tip fully until it stops with a click Turning the tip to keep the cleaning effect The cleaning effects decreases when the tip is used the following number of times White tip Cleaning about 30 times Black tip Cleaning one time To regain the original cleaning effect reinsert the tip as shown below so that you can clean the head with the unused surface of the tip Pull out the tip turn it 90 then reinsert it One tip provides four new surfaces After using all unused surfaces exchange the tip for a new one The cleaning tip set is available using part number A 8279 104 at a charge Cleaning of the thermal head To clean the thermal head proceed as follows T Remove the ink ribbon cassette from the printer 2 Attach the cleaning tip to the cleaning tip holder and install the cleaning tip holder in the printer The cleaning tip holder can be mounted in the same way as that of the ink ribbon cassette 3 Insert the cleaning tip holder fully until it stops then pull the holder out until the open window of the holder fully appears Repea
Download Pdf Manuals
Related Search