Sony RM-PP506L User's Manual
Contents
1. When programmed successfully the indicator lights twice slowly then the remote automatically exits the macro setting mode 4 Repeat steps 1 through 3 to program up to 10 IR codes Tip To program a function switch press the same function button twice in step 3 e If programming is unsuccessful check the following If the indicator does not light up in step 1 the batteries are weak Replace both batteries If the indicator lights 4 times in quick succession in step 3 an error has occurred Start again from step 1 Note The indicator turns off while a valid button is pressed To cancel programming Press USE MODE during any step The remote automatically exits the macro setting mode To delay the output of an IR code Start over from step 1 In step 3 press VIDEO 1 then MACROI MACRO2 This allows you to specify 1 second delay before output the next IR code Be sure not to press 1 or MACRO for more than 2 seconds To clear the programmed IR codes Clear each macro step individually 1 Press MACRO1 or MACRO2 in which the IR code you want to clear is programmed while pressing down USE MODE 2 Press the numeric button to select the macro step number you want to clear Press VIDEO 1 4 down MACRO1 or MACRO for more than 2 seconds The IR code is cleared The indicator lights twice slowly then the remote automatically exits the macro setting mode To start macro play Pres2. TEST TONE button Press to output a test tone SLEEP button Press repeatedly to activate the sleep function and the duration which the receiver turns off automatically Not available with STR DAIES continued suol ei9dQ JISeg Sed uol eI207 598 6 5 Parts description continued VIDEO1 VIDEO2 VIDEO3 DVD LD TV SAT CD SACD TUNER PHONO m 2ND ROOM O00000 TVNIDEO Soe MACRO2 7 8 8 SHIFT ENTER 14 AV 1 0 switch Press to turn the selected audio and video components under the function button on or off If you press the 1 C switch at the same time it will turn off the main component and other Sony audio video components SYSTEM STANDBY Note The function of the AV 1 switch changes automatically each time you press the function buttons 11 Depending on the component the above operation may not be be possible or may operate differently than described 15 ANT TV VTR DISC button Mm ho La gt 9 eG D SKIP VOL MUTING PINP Co Oo 50 IELD AV TEST EQ MULTV2CH DISPLAY TONE A DIRECT Press repeatedly to select the signal to be output from the antenna terminal of the VCR TV signal or video signal With a CD player press to select disc
3. See the table on page 10 for information on the buttons that you can use to control each component 24 SHIFT gt 10 button Button s Function Ke PP1 Skips tracks lt gt Fast forwards or rewinds Searches tracks in the forward or backward direction Starts play on the reverse side of the cassette Starts play Starts play on the front side of the cassette H Pauses play or recording or starts recording when the component is in recording standby E Stops play If you selected tuner Press repeatedly to select a memory page for presetting radio stations or tuning to preset stations If you selected VCR TV LD player tape deck MD deck or CD player Press before inputting a channel or track number of eleven or higher 25 CLEAR D TUNING button If you selected DVD player Press if you made a mistake when you press the numeric buttons If you selected TV or VCR Press to select the channel entry mode either one or two digit If you selected tuner Press to start direct tuning 26 SEARCH MODE button Press to select the search mode of DVD player 27 Indicator Lights up whenever any button on the remote is pressed and operating 28 USE MODE button Use to program the remote The function of these buttons switch automatically each time you press the function buttons 1 The above explanation is intended t
4. ones Notes e Do not leave the remote in an extremely hot or humid place e Do not use a new battery with an old one Do not expose the remote sensor of the receiver to direct sunlight or lighting apparatuses Doing so may cause a malfunction If you don t use the remote for an extended period of time remove the batteries to avoid possible damage from battery leakage and corrosion Table of Contents Location of Parts and Basic Remote Operations Parts 4 Table of buttons that you can use to control each component 9 Advanced Remote Operations Programming the remote 10 Learning the commands of your COMPONENUS 13 Performing several commands in sequence automatically Macro 14 Selecting the mode of the remote 15 Additional Information Troubleshooting Back cover Specifications Back cover Location of Parts and Basic Remote Operations 1 Function buttons This chapter provides information on the Press one of the buttons to select the location of buttons and how to use them to component you want to use When you perform basic operations press a button the receiver turns on The However some functions explained in this components are factory assigned to
5. 530 537 539 TOSHIBA 535 540 541 ZENITH 542 543 To control a satellite tuner or cable box Maker Code s SONY 801 802 803 JERROLD G I 806 807 808 809 810 811 812 813 814 PANASONIC 818 RCA 804 805 S ATLANTA 815 816 817 Learning the commands of your components By using the Learning function it is possible for this remote to perform learned commands Setting remote control codes that are not stored in the remote When a remote control code is not one of the presets stored in the remote it is possible for the remote to learn the code using the Learning function 1 Press SLEEP while pressing down USE MODE The indicator lights 2 Press the function button for the component you want to learn functions for For example if you are going to learn an operation for a CD player press CD 3 Press the button you want to use for the Learning function The indicator turns off while a valid button is pressed then blinks slowly 4 Point the remote control code receiver section of the remote toward the receiver transmitter on the remote control to be learned 5 Press the appropriate button on the remote control to be learned to send the remote button code Lightly pressing the button once should be sufficient If learning is completed successfully the indicator slowly lights twice and the remote automatically exits the learning mode If the memory of the remote is al
6. MENU SCREEN 46B Remote mode buttons Press to select the mode of the remote page 15 MACRO 1 2 buttons Press to use Macro Play function page 14 SOUND FIELD buttons AUTO DEC button Press to set the receiver to automatically select the appropriate sound field for the input signal This button can be used only with receivers that have digital inputs MODE buttons Press to select sound fields 2CH button Press to turn the sound field off and listen to 2 channel stereo sound Multi channnel source is also downmixed to a 2 channel stereo sound PRESET button Press to select CINEMA STUDIO A B or etc MULTI 2CH A DIRECT button Press to select the multi channel input sources 10 1 12 13 EQ TONE button Press to turn the tone effect on or off Note that if you have adjusted the tone using the MAIN MENU button and cursor buttons the adjusted tone will be produced whenever you turn on the tone effect MUTING button Press to mute the sound ON SCREEN button Press to display the menus of the receiver on the TV screen MASTER VOLUME buttons Press to adjust the volume level of all speakers at the same time MAIN MENU button Press to select the cursor mode of the receiver SET UP LEVEL etc NIGHT MODE button Press to select NIGHT MODE
7. S O N 4 241 678 11 1 Remote Commander Operating Instructions Owner s Record The model and serial numbers are located on the rear of the unit Record the serial number in the space provided below Refer to them whenever you call upon your Sony dealer regarding this product Model No 9 Serial No RM PP506L 2002 Sony Corporation Precautions About this manual The instructions in this manual are for model On safety Should any solid object or liquid fall into the cabinet RM PPS506L Check your model number by unplug the receiver and have it checked by qualified looking at the lower right corner of the front personnel before operating it any further side On operation Before connecting other components be sure to turn off and unplug the receiver On cleaning Clean the cabinet panel and controls with a soft cloth slightly moistened with a mild detergent solution Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine If you have any question or problem concerning your remote please consult your nearest Sony dealer 2GB Before you use your remote Inserting batteries into the remote Insert two R6 size AA batteries with the and properly oriented in the battery compartment est Tip Under normal conditions the batteries should last for about 6 months When the remote no longer operates the receiver replace both batteries with new
8. e you can adjust the volume of speakers in another room when you set the receiver to output the sound using SPEAKER terminals You can use the function buttons and MASTER VOL buttons only Press 3 3RD while pressing down USE MODE The indicator lights 3 times then the mode switches to the 3rd room mode To check the mode of the remote Press USE MDOE You can check the remote by the indicator Mode Indicator lights AV2 twice 2nd room once for a while 3rd room 3 times Not available with STR DAIES 1598 Additional Information Troubleshooting If you experience any of the following difficulties while using the receiver use this troubleshooting guide to help you remedy the problem Should any problem persist consult your nearest Sony dealer The remote does not function e Check the mode of the remote page 15 e Point the remote at the remote sensor on the receiver Remove any obstacles in the path between the remote and the receiver e Replace both batteries in the remote with new ones if they are weak Make sure you select the correct function on the remote Sony Corporation Printed in Malaysia Specifications General Remote control system Infrared control Power requirements 3 V DC with two R6 size AA batteries Dimensions 210 x 68 x 25 mm Mass approx 120 g excluding batteri
9. es Design and specifications are subject to change without notice http www sony net
10. inued To control a VCR Maker Code s SONY 701 702 703 704 705 706 AIWA 710 750 757 758 AKAI 707 708 709 759 BLAUPUNKT 740 EMERSON 711 712 713 714 715 716 750 FISHER 717 718 719 720 GENERAL ELECTRIC 721 722 730 GOLDSTAR 723 753 GRUNDIG 724 HITACHI 722 725 729 741 ITT NOKIA 717 JVC 726 727 728 736 MAGNAVOX 730 731 738 MITSUBISHI MGA 732 733 734 735 NEC 736 PANASONIC 729 730 737 738 739 740 PHILIPS 729 730 731 PIONEER 729 RCA PROSCAN 722 729 730 731 741 747 SAMSUNG 742 743 744 745 SANYO 717 720 746 SHARP 748 749 TELEFUNKEN 731752 TOSHIBA 747 755 756 ZENITH 754 To control a DVD player Maker Code s SONY 401 PANASONIC 402 406 PHILIPS 407 PIONEER 403 TOSHIBA 404 DENON 405 1228 control TV Code s SONY 501 DAEWOO 504 505 506 507 515 544 FISHER 508 GOLDSTAR 503 511 512 515 534 544 GRUNDIG 517 534 HITACHI 513 514 515 544 ITT NOKIA 521 522 JVC 516 MAGNAVOX 503 518 544 MITSUBISHI MGA 503 519 544 NEC 503 520 544 PANASONIC 509 524 PHILIPS 515 518 PIONEER 509 525 526 540 RCA PROSCAN 510 527 528 529 544 SAMSUNG 503 515 531 532 533 534 544 SANYO 508 545 SHARP 535 TELEFUNKEN 523 536 537 538 THOMSON
11. mponent accepts differs depending on the model and year of the component more than one numeric code may be assigned to a component If you fail to program your remote using one of the codes try using other codes Notes The numeric codes are based on the latest information available for each brand There is a chance however that your component will not respond to some or all of the codes All of the functions on this remote may not be available when used with your particular component To control a CD player Maker Code s SONY 101 102 103 DENON 104 123 JVC 105 106 107 KENWOOD 108 109 110 MAGNAVOX 111 116 MARANTZ 116 ONKYO 112 113 114 PANASONIC 115 PHILIPS 116 PIONEER 117 TECHNICS 115 118 119 YAMAHA 120 121 122 To control a DAT deck Maker Code s SONY 203 PIONEER 219 To control an MD deck Maker Code s SONY 301 DENON 302 JVC 303 KENWOOD 304 To control a tape deck Maker Code s SONY 201 202 DENON 204 205 KENWOOD 206 207 208 209 NAKAMICHI 210 PANASONIC 216 PHILIPS 211 212 PIONEER 213 214 TECHNICS 215 216 YAMAHA 217 218 To control an LD player Maker Code s SONY 601 602 603 PIONEER 606 To control a video CD player Maker Code s SONY 605 continued 1198 Programming the remote cont
12. nal MONITOR button Press to active TV control buttons The button lights up Press again to restore original category The function of these buttons switch automatically each time you press the function buttons 1 The above explanation is intended to serve as an example only Therefore depending on the component the above operation may not be possible or may operate differently than described Only with Sony TVs with the picture in picture function Table of buttons that you can use to control each component Component CD DAT MD Tape LD VCR TV Satellite Video DVD player deck deck deck player tuner cD player A and B Cable box player Button s 1 Numeric buttons SHIFT gt 10 4 VOL gt Return VOL MUTING kea P gt Pl lt lt gt gt SUB D SKIP CH PRESET ANT TV VTR DISC CLEAR D TUNING AV MENU TITLE GUIDE Cursor buttons ENTER EXEC EXIT RETURN AV DISPLAY TV VIDEO SEARCH MODE suoljei9dQ JISeg Sed B deck only With a multi disc changer only Advanced Remote Operations This chapter describes how to change the factory setting of a function button and h
13. o serve as an example only Therefore depending on the component the above operation may not be possible or may operate differently than described continued suolj ei9dQ JISeg Sed Parts description continued TV operation After pressing the MONITOR button the button lights up and you can use the following buttons to operate TV WO USEMODE SYSTEM STANDBY SLEEP VIDEO1 VIDEO2 VIDEO3 DVDD TVISAT CICILY MD DAT CD SACD TUNER PHONO TAPE SOUND FIELD AUTO DEC 2CH_ PRESET MODE COG GC Co MULTV2CH A DIRECT ON SCREEN MUTING 8 5 29 Numeric buttons 1 to 0 Press to select channel numbers 30 JUMP button Press to toggle between the previous and the current channels POSITION button Press to change the position of the small picture SWAP button Press to swap the small and large pictures 33 P IN P button Press to activate the picture in picture function 34 MUTING button Press to mute the sound 35 VOLUME buttons Press to adjust the volume of TV 36 SUB CH buttons Press to change the sub channel selection WIDE button Press to switch the TV to the wide mode 28 TV VIDEO button Press to select the TV input sig
14. ow to set the remote to control non Sony components Programming the remote You can program the remote to control non Sony components by changing the code Once the control signals have been memorized you can use those components as part of your system Furthermore you can also program the remote for Sony components that the remote is unable to control Note that the remote can only control components that accept infrared wireless control signals Note When you assign a component to the MONITOR button you can operate the programmed component without changing the function of the receiver 1 Press AV 1 while pressing down USE MODE The indicator lights 2 Press the function button including MONITOR for the component you want to control For example if you are going to control a CD player press CD 3 Press the numeric buttons to enter the numeric code or one of the codes if more than one code exists corresponding to the component and the maker of the component you want to control See the tables on pages 11 and 12 for information on the numeric code s corresponding to the component and the maker of the component the first digit and the last two digits of the numeric code correspond to the category and the maker s code respectively 1098 4 Press ENTER Once the numeric code has been verified the indicator slowly lights twice and the remote automatically exits the programming mode 5 Repeat s
15. ready full the indicator flashes 8 times in quick succession and the remote automatically exits the learning mode When learning is not completed successfully the indicator lights 4 times in quick succession and the procedure returns to step 5 Notes e You can program up to 80 buttons for the Learning function In some cases you may not be able to program even if you have not programmed 80 buttons e In steps 2 and 3 the indicator turns off while a valid button is pressed e In step 3 if several buttons that can be used for learning are pressed only the last pressed button is valid In step 5 if a button that can be used for learning is pressed the new button is selected and the learning procedure returns to the beginning of step 5 e You can use TV VIDEO only for the MONITOR function To cancel learning Press USE MODE during any step The remote automatically exits the learning mode To clear the learned codes Start over from step 1 After step 3 press SLEEP for more than 2 seconds The indicator lights twice slowly and the learned code is cleared When a learned code is cleared if the button was previously programmed for another function the programmed code for that button can be used continued 1388 Learning the commands of your components continued To clear the memory of the remote To clear all programmed and learned signals do the follo
16. s mega storage CD player only 16 ENTER button Press to enter the selection 17 D SKIP CH PRESET buttons If you selected tuner Press to scan and select preset stations If you selected TV VCR or SAT Press to select preset channels If you selected CD player Press to skip discs CD player with multi disc changer only 18 AV MENU button Press to display the menus of the VCR satellite tuner or DVD 19 EXIT RETURN button After pressing the AV MENU or TITLE GUIDE button press to return to the previous menu or exit the menu The function of these buttons switch automatically each time you press the function buttons 1 The above explanation is intended to serve as an example only Therefore depending on the component the above operation may not be possible or may operate differently than described N 45 Cursor buttons A V lt gt EXEC button After pressing the MAIN MENU AV MENU or TITLE GUIDE button use the cursor buttons to make specific settings then press the ENTER EXEC button to enter the selection TITLE GUIDE button Press to display DVD titles or guide menus AV DISPLAY button Press to select the information displayed on the TV screen Operation buttons The following table describes the component operated by each button and the function of the buttons
17. s MACRO1 or MACRO2 Note If the Macro Play function does not work properly program a delay between each operation See To delay the output of an IR code Selecting the mode of the remote Set the remote mode using the USE MODE button 28 and the remote mode buttons 2 Selecting the command mode You can switch the command mode AV1 or AV2 of the remote If the command mode of the receiver and the remote is different you cannot use the remote to operate the receiver Initial setting is AV1 Press 1 AV1 or 2 AV2 while pressing down USE MODE The indicator lights once twice for AV2 then the command mode switches Setting to the 2nd room mode You can use the remote to select the function for the 2nd room 2nd room mode You can use the function buttons only for the 2nd room Press 2ND ROOM while pressing down USE MODE The indicator lights for a while then the mode switches to the 2nd room mode Tips e If you press a function button while pressing down 2ND ROOM you can select the function for the 2nd room even though the mode is not set to the 2nd room mode If you press 2ND ROOM only you can output the source signal of the current function of the receiver to the amplifier in the 2nd room Setting to the 3rd room mode You can use the remote to select the function for the 3rd room and adjust the volume in the 3rd room 3rd room mode During 3rd room mod
18. teps 1 to 4 to control other components To cancel programming Press USE MODE during any step The remote automatically exits the programming mode Tips If programming is unsuccessful check the following If the indicator does not light up in step 1 the batteries are weak Replace both batteries If the indicator lights 4 times in quick succession while entering the numeric code an error has occurred Start again from step 1 To activate the function after programming press the programmed button to activate the function you want Notes The indicator turns off while a valid button is pressed In step 2 if several function buttons are pressed only the last pressed button is valid In step 3 if a function button is pressed the new function is selected and the programming procedure returns to the beginning of step 3 For the numeric codes only the first three numbers entered are valid To clear the memory of the remote To clear all programmed and learned signals do the following to reset the remote to factory settings Press 1 0 AV 1 and MASTER VOL at the same time The indicator lights 3 times then goes off The numeric codes corresponding to the component and the maker of the component Use the numeric codes in the tables below to control non Sony conponents and also Sony components that the remote is normally unable to control Since the remote signal that a co
19. the section may not work depending on the model buttons as follows When you want to of the receiver assign other components program the For the functions of the receiver you purchased remote following the steps on page 10 refer to the Operating Instructions supplied Button s Assigned with the receiver component s VIDEO VCR VTR mode 3 VIDEO2 VCR VTR mode 1 inti VIDEO3 VCR VTR mode 2 Parts description DYD LD DVD player TV SAT TV tuner wie VO TAPE Tape deck MD DAT MD deck USEMODE SYSTEM CD SACD CD player VIDEO1 VIDEO2 VIDEO3 DVD LD TV SAT ae TUNER Built in tuner CD SACD TUNER PHONO Turntable J 0 12 See the table on page 9 for information E5 6 Cy 3 the buttons that you can use to control each Soe MACRO 2 component 8 ole CLEAR SHIFT ENTER TVNTR GD 0 a DETUNING M n2 JUMP Note that the function buttons are factory set as described in the table above If you want to change the factory setting of the buttons to match your particular components do the procedure Programming the remote on page 10 SUBCH POSITION SWAP 0 OY VOL MUTING CHIPRESET o oe O SOUND FIELD A TO DEC MODE 2 O TEST EQ SANE PRESET 2 ON
20. wing to reset the remote to factory settings Press 1 0 AV 1 and MASTER VOL at the same time The indicator lights 3 times then goes off To use a command that has been learned When selecting a learned function press the learned button for that function Performing several commands in sequence automatically Macro Play The Macro Play function lets you link several IR codes in a sequential order as a single command The remote provides 2 macro lists MACRO and 2 You can specify up to 10 IR codes for each macro list Setting the sequence of IR codes 1 Press MACRO1 or MACRO2 while pressing down USE MODE The indicator lights 2 Press the numeric buttons to select the macro step number For example to program step 1 press 1 1488 3 Press the button you want to program To program the operation IR code of a component connected to the receiver press the function button including MONITOR first then press the button for the operation For example to play the CD player press CD then press D gt When programmed successfully the indicator lights twice slowly then the remote automatically exits the macro setting mode To program the operation IR code of the receiver press the button for the operation Buttons that can be programmed SLEEP 1 2ND ROOM AUTO DEC MODE 2CH PRESET TEST TONE NIGHT MODE EQ MULTI 2CH A DIRECT ON SCREEN MUTING MAIN MENU MASTER VOL
Download Pdf Manuals
Related Search