Sony ICF-M88B Operating Instructions
Contents
1. 2 Push the J og lever towards or to select the preset number to be deleted 3 Hold down TUNE MODE for more than 2 seconds until PRESET d and the preset number flash rr ax 3 ag g 3 preset number to be deleted 4 While the letters and the preset number are flashing press ENTER SELECT The station set to the preset number just before the deleted station will be displayed To delete other stations repeat steps 2 to 4 If all the preset stations are deleted PRESET appears in the display To cancel deleting press TUNE MODE while PRESET d and the preset number are flashing Playing the Radio on the Mount When the current speed is displayed for example after having installed the unit on the Mount pressing a button or the Jog lever to perform a radio operation only displays the station frequency and or current preset number From this display press the BAND SET TUNE MODE or Jog lever or to perform the desired radio operation Holding down Jog lever or ENTER SELECT or TUNE MODE while the current speed is displayed Jog lever or Pushing the Jog lever displays the current frequency Pushing and holding the Jog lever changes the frequency or preset number ENTER SELECT Pressing this button displays the current frequency Pressing and holding selects the Station presetting mode TUNE MODE Pressing this button displays the current freq2. are set to zero You can reset maximum speed only Select MAX in step 1 followed by step 2 and 3 Setting Freeze mode You can deactivate odometer calculation trip distance riding time average time and maximum speed except for current speed with the Freeze mode 1 Press and hold MODE FREEZE for a few seconds FREEZE lights up and the cycle computer enters Freeze mode To cancel Freeze mode press and hold MODE FREEZE for a few seconds FREEZE is no longer displayed Standby mode When your bicycle is stopped with the radio off and no button is pressed for more than 10 minutes the cycle computer enters Standby mode and only the current time is displayed To cancel Standby mode When the unit is attached to the Mount At the point where you start and the magnet passes the sensor or you press any active button Standby mode is canceled The display returns to the previous one before entering Standby mode When the unit is not attached to the Mount When you attach the unit to the Mount or press any active button Standby mode is canceled Note If the cycle computer enters Standby mode with Freeze mode activated Freeze mode is not canceled Using the Backlight Press LIGHT The backlight will light for 10 seconds If any buttons are pressed while the backlight is on the backlight will turn off 10 seconds after pressing the button Setting the Clock The clock time display of this uni
3. if it should fall into water take it out immediately and wipe it off with a dry cloth To prevent the battery from corroding wipe out the interior of the battery compartment as follows Open or close the battery compartment with dry hands in a place without exposure to any water Wipe off the battery and the inside of the battery compartment Give special attention to the contacts so that no water remains on them Notes on the cycle computer radio e The user must obey all traffic laws when using the device e To check whether the local laws allow the use of the device e In order to prevent dangerous condition do not operate the device when running the bicycle e In order to prevent theft take your device with you at all times e In order to prevent dangerous condition install the sensor cord properly so that it will not get tangle by the tire If you have any questions or problems concerning your unit please consult your nearest Sony dealer The preset stations may be initialized if a maintenance service is performed Please keep a copy of your settings in case you want to preset them again Specifications Time display 12 hour system Frequency range Band Range Channel step FM 87 5 108 MHz 0 1 MHz AM 530 1 710 kHz 10 kHz 531 1 710 kHz 9 kHz Speaker Approx 50 mm 2 inches dia 8Q Power output 80 mW at 10 harmonic distortion Power requirements 3V DC two size AA R6 batteries Dimens
4. unit wheel size and total distance entered will be erased The unit will revert to the previous setting The cycle computer will not activate during the initial setting mode If you press RADIO POWER to turn on the unit during the initial setting mode the mode is canceled and the radio will activate If you change the unit in the initial setting mode the values showed in the total distance odometer setting mode will be automatically converted into the new setting unit However when you convert the unit from miles to kilometers any value over 159 999 9km is shown as 159 999 9km Displaying data While cycling current speed is always displayed and updated every second The highest speed that can be displayed is 124 2 MPH 199 9 km h and remains displayed beyond that speed Below 2 5 MPH 4 0 km h 0 0 is displayed Displaying the odometer Press MODE FREEZE repeatedly until ODO appears The current total distance is displayed Note If 99 999 9 miles 160 934 3 km is exceeded the odometer returns to zero Displaying trip distance Press MODE FREEZE repeatedly until DIST appears At the point you want to start calculating the distance perform the zero reset operation For details on how to perform the zero reset operation refer to Performing the zero reset Note If 9 999 9 miles 16 093 3 km is exceeded the trip distance returns to zero Displaying riding time Press MODE FREEZE repeat
5. SONY 3 267 406 11 1 FM AM PLL Synthesized Radio Operating Instructions Printed on 100 recycled paper using C F M88 B VOC Volatile Organic Compound free vegetable oil based ink 2004 Sony Corporation Printed in China http www sony net OWNER S RECORD The model number is located on the left side of the front panel and the serial number is inside the battery compartment Record the serial number in the space provide below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No ICF M88B Serial No For customers who purchased this product in the USA Please register this product on line at http www sony com productregistration Proper registration will enable us to send you periodic mailings about new products services and other important announcements Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification Thank you Tape Cassette Player Recorder CD Player Mini Disc DAT Radio Head Phone Speaker MIC Personals LIMITED WARRANTY Sony Electronics Inc Sony warrants this Product including any accessories against defects in material or workmanship as follows SONY 1 LABOR For a period of one 1 year from the date of purchase if this Productis determined to be defective Sony will repair or replace the Product at its option at no charge or
6. band will be initialized 1 Press RADIO POWER to turn off the power 2 While holding down ENTER SELECT keep pressing RADIO POWER for more than 5 seconds Two short beeps sound and the AM channel step will change and 9 kHz or 10 kHz will light up for about 2 seconds in the display If you proceed to step 2 again the channel step changes again Playing the Radio Manual Tuning 1 Press RADIO POWER to turn on the power 2 If PRESET is displayed press TUNE MODE so that PRESET disappears Pressing TUNE MODE will switch over between manual tuning mode and preset tuning mode 3 Press BAND SET to select the band Each press changes the band 4 Push the Jog lever towards or to select the desired frequency If you hold down the Jog lever towards or the frequency changes rapidly When the frequency matches the broadcast frequency the broadcast will be received 5 Adjust the volume using VOL To turn off the radio press RADIO POWER Improving Radio Reception FM Set FM SENS to LOCAL if interference is prevalent when radio wave intensity is dramatically stronger Under normal conditions set to DX Presetting your Favorite Stations Preset Tuning You can preset up to 5 AM stations and 10 FM stations You can also delete a preset station whether factory set or preset yourself Presetting a Station 1 Follow steps 1 to 5 in Playing the Radio and manually tune i
7. diameter of the handlebar You can attach the Mount clamps without the rubber pads if not required Mount clamp Mount with wheel sensor Thin rubber pads LE Thick rubber pads The Mount clamps are adjustable You can adjust the width of the clamps to fit your handlebar 2 Install the Mount on the rubber pads and secure with the 4 screws Sensor cord Note Be sure to allow enough cord slack to ensure full movement and unhindered operation of the handlebar and not to wind it too loosely as this may interfere with the unit s operation 4 Temporarily attach the Sensor to a fork using the attached Double sided tape Sensor Wheel magnet e When attaching align the center of the sensor and that of the magnet triangle mark e Ensure a clearance not exceeding 4mm except Sensor and Magnet touching between the Sensor and the Wheel magnet when aligned e Attach the unit on the Mount and then check the reaction of the sensor by revolving the wheel See fig Install the unit 5 After determining the position of the Sensor secure it with the zip tie to front fork and cut any surplus Install the Sensor cord with zip ties such that it does not become tangled with the wheel Note Be careful that the position of the Sensor does not shift when tightening the zip tie Install the unit Install the unit on the Mount sliding from the front until it clicks into position Remove the unit Pull the u
8. ed to obtain warranty service This warranty is invalid if the factory applied serial number has been altered or removed from the Product REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIB ITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU LAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you In addition if you enter into a service contract with the Sony Partnership within 90 days of the date of sale the limitation on how long an implied warranty lasts does not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state For your convenience Sony Electronics Inc has established telephone numbers for frequently asked questions To locate the servicer or dealer nearest you or for service assistance or resolution of a service problem or for product information or operation call Sony Customer Information Services Center 1 800 222 7669 or visit the Sony Web Site wwwsony com For an accessory or
9. edly until RT appears The Hour Minute Second is indicated in the display At the point you want to start calculating riding time perform the zero reset operation For details on how to perform the zero reset operation refer to Performing the zero reset Riding time is updated every second When one wheel revolution takes over a second riding time is updated when the magnet passes the sensor If the interval at which the magnet passes the sensor is more than 1 minute the calculation is canceled Note If the displayed 99 59 59 is exceeded riding time returns to zero Displaying average speed Press MODE FREEZE repeatedly until AVG appears Average speed is calculated according to trip distance and riding time Displaying maximum speed Press MODE FREEZE repeatedly until MAX appears The maximum speed recorded to date is displayed Note If either trip distance or riding time returns to zero trip distance riding time and average speed simultaneously return to zero Performing the zero reset The zero reset operation of trip distance riding time and average speed are performed simultaneously and cannot reset individually 1 Press MODE FREEZE to display either DIST RT or AVG 2 Press and hold RESET for a few seconds DIST RT and AVG flash 3 Press RESET again The zero reset operation is completed and DIST RT and AVG
10. ions Approx 166 8 x 70 x 95 mm w h d 6 x 2 x 3 inches incl projecting parts and control Mass Approx 281 4 g 9 93 oz incl batteries excl accessories Supplied accessories Mount with wheel sensor 1 Thick Thin rubber pads 2 each Wheel magnet 1 Zip ties 5 Double sided tape 1 Screws 2 Design and specifications are subject to change without notice Installing the Batteries 1 Slide OPEN to open the battery compartment lid and install two size AA R6 batteries not supplied with correct polarity When the batteries are first installed AM 12 00 flashes in the display Once the current time is set the flashing stops See Setting the Clock Size AA R6 x 2 Insert the side of the battery first Packing inside of the lid is used to ensure water resistance for the battery compartment Therefore make sure to close the battery compartment lid securely 2 Close the lid Battery Life Approx hours JEITA When using FM AM Sony alkaline size AA LR6 66 84 Sony size AA R6 23 31 Measured by JEITA Japan Electronics and Information Technology Industries Association standards The actual battery life may vary depending on circumstances of use Replace the batteries When the batteries become weak the sound may become weak or distorted and A7 will flash in the display After that when the batteries are used up C1 will light up and clock time dis
11. lay as follows eo ee 24 22 20 18 16 Note The mm values shown on the display are approximate Adjust the accurate size of the wheel using Jog lever or after measuring diameter of your wheel It is recommend to set the wheel size in mm because the cycle computer calculates in mm If you set the wheel size in mm the range is from 300 to 750 mm Push and hold Jog lever to change the value rapidly 3 Press BAND SET ODO appears in the display and the last digit of the total distance odometer flashes If you do not change the odometer jump to step 4 To change the total distance You can change the default setting of the total distance odometer using Jog lever or to increase or decrease and ENTER SELECT to select another digit 4 Press BAND SET again The initial setting is completed Tips e When you choose the mile the range is from 0 0 to 99 999 9 miles e When you choose the km the range is from 0 0 to 159 999 9 kilometers And the maximum digit range is from 0 to 15 Notes If you do not make any selections for within about 65 seconds or do press TUNE MODE button during the initial setting mode the setting mode will be canceled and the unit returns to the previous mode If you press the LIGHT button for within about 65 seconds during the initial setting mode the setting mode will be extended If you cancel during initial setting mode the value of the
12. n to the station you wish to preset 2 Hold down ENTER SELECT until the preset number flashes A preset number with no station will flash When all preset numbers have assigned stations factory set 1 flashes and PRESET appears 3 Push the J og lever towards or to select the number you wish to preset then press ENTER SELECT If a preset number you select with the Jog lever has an assigned preset station PRESET appears if no station is assigned only the number flashes When you press ENTER SELECT the selected preset number lights up in the display Example Preset number 2 FM 90 0 MHz PRESET To preset another station repeat the above steps To change a preset station preset a new station The previous station will be canceled Note If you do not perform a preset operation for about 65 seconds presetting mode will be canceled Tuning in to a Preset Station 1 Press RADIO POWER to turn on the power Press BAND SET to select the band Press TUNE MODE so that PRESET and preset number appear 2 3 4 Push the Jog lever towards or to select the desired preset number 5 Adjust the volume using VOL To turn off the radio press RADIO POWER Note If you hold down TUNE MODE for more than 2 seconds the unit enters the preset station deleting mode Press TUNE MODE again to return to the previous mode Deleting a Preset Station 1 Follow steps 1 and 3 in Tuning in to a Preset Station
13. nit forward while pushing down the lever Note Ensure that the contact points between the Mount and the unit are clean for proper operation Caution For safe and proper use of the cycle computer check whether the Mount the sensor and its cord and the wheel magnet are set properly before riding CX FREEZE preset arg ru 1 Pad Papa Tn An AM TC DA o NA DA oA OA MPH pur CEL ENE A ee CLOCK ODO DIST RT AVG MAX RADIOPOWER LIGHT ENTER SELECT TUNE MODE BAND SET RESET MODE FRE SE Jog lever _ RADIOPOWER FM SENS DX LOCAL FM antenna VOL There is a tactile dot beside VOL to show the direction to turn up the volume For the initial setting with the radio off The cycle computer needs initial set up before using If the wheel size you set into the cycle computer is not suitable for using actual wheel size it is not possible to measure speed and distance correctly 1 Press and hold BAND SET for a few seconds to select mile or km mile flashes in the display Each press of the ENTER SELECT toggles between mile and km The unit of speed is MPH for miles and km h for kilometers Select and show the desirred unit 2 Press BAND SET to set a wheel size The wheel size flashes SM HUET TANS THe mZ LIZ 3 3 Press ENTER SELECT repeatedly to select your wheel size inches Each press changes the disp
14. part not available from your authorized dealer call 1 800 488 SONY 7669 D 455714502 WARNING You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Features e FM AM PLL phase locked loop synthesized radio with built in cycle computer e New ergonomic de
15. pay the labor charges to any Sony autho rized service facility After the Warranty Period you must pay for all labor charges 2 PARTS In addition Sony will supply at no charge new or rebuilt replacements in exchange for defective parts for a period of one 1 year After the warranty period you must pay for all parts costs 3 ACCESSORIES Parts and labor for all accessories are for one 1 year To obtain warranty service you must take the Product or deliver the Product freight prepaid in either its original packaging or packaging affording an equal degree of protection to any authorized Sony service facility This warranty does not cover customer instruction installation set up adjustments or signal reception prob lems This warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negli gence commercial use or modification of or to any part of the Product including the antenna This warranty does not cover damage due to improper operation or maintenance connection to improper voltage supply or attempted repair by anyone other than a facility authorized by Sony to service the Product This warranty does not cover Products sold AS IS or WITH ALL FAULTS or consumables such as fuses or batteries This warranty is valid only in the United States Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be present
16. play appears And then the cycle computer function will be stopped so that any button functions will not work The Radio function will be also turned off if it is on If this happens replace the batteries with new ones After the batteries are replaced press RADIO POWER RESET or install the unit on the Mount amp turn off in the display Note on replacing the batteries Do not take more than 5 minutes to replace the batteries otherwise the clock setting will be initialized Should that happen reset the functions Notes on batteries Do not charge the dry batteries e Do not carry the dry batteries together with coins or other metallic objects It can generate heat if the positive and negative terminals of the batteries accidentally come into contact with metallic objects When you are not going to use the unit for a long time remove the batteries to avoid damage from battery leakage and corrosion Do not use different types of batteries at the same time e When you replace the batteries replace all with new ones Installing the unit on the bicycle Install the Wheel Magnet 1 Remove the screw of the wheel magnet and open 2 Attach the magnet between two spokes of the front wheel with the head of the screw facing inward and tighten the screw Install the Mount 1 Choose the appropriate rubber pads according to the diameter of the handlebar and attach them Use one or two rubber pads depending on the
17. sign e Water resistant for all weather use e 15 station memory presets LOFM 5AM e Easy Jog lever operation e Easy to see backlit LCD e Easy to install mounting kit included e FM SENS DX Distance LOCAL switch Precautions e Operate the unit only on 3 V DC with two size AA R6 batteries e Avoid exposure to temperature extremes direct sunlight moisture sand dust or mechanical shock Never leave in a car parked under the sun e Avoid continuous exposure to direct sunlight or extremely high temperatures to prevent possible damage to the display The display will function normally again in normal operating temperature e Display switching may become slower in cold climates Should any solid object or liquid fall into the unit remove the batteries and have the unit checked by a qualified personnel before operating it any further e To clean the casing use a soft cloth dampened with a mild detergent solution e Since a strong magnet is used for the speaker Keep away personal credit cards using magnetic cording or spring wound watches from the unit to prevent possible damage from the magnet Cautions on Water resistance This unit is designed so that it can be used with slight exposure to rain snow and other forms of moisture but there are several points on which caution should be observed Do not allow it to come into contact with large amounts of water e Do not immerse it in water e If water should get on it or
18. t is a 12 hour system When the batteries are first installed AM 12 00 flashes and CLOCK turns on in the display 1 Press RADIO POWER to turn off the power 2 Press MODE FREEZE repeatedly until CLOCK appears 3 Hold down ENTER SELECT for more than 2 seconds until AM 12 starts flashing 4 Push the Jog lever towards or to adjust the hour then press ENTER SELECT The beep sounds and the minute setting starts to flash If you hold down the Jog lever towards or the digit changes rapidly Midnight is indicated as AM 12 00 and Noon is indicated by PM 12 00 iW 4 sg aie g z S d 5 Repeat step 4 above to adjust the minutes starts flashing and the clock starts operating To set the current time exactly to the second adjust the minute setting and then press ENTER SELECT to synchronize it with a time signal such as the telephone time signal Note If you do not push the Jog lever towards or or ENTER SELECT within about 65 seconds the clock setting mode will be canceled Changing AM Channel Step The AM channel step differs depending on area The channel step of this unit is factory set to 10 kHz Change the settings as shown below to be able to listen to the radio Area Channel step North and South American countries 10 kHz Other countries regions 9 kHz Note When the AM channel step is changed only the preset stations on the AM
19. uency Pressing and holding selects preset station deleting mode in preset tuning mode In manual tuning mode holding down has no effect Notes If you perform a radio operation once in the current speed display and do not operate the radio again within 5 seconds the display automatically returns to the current speed indication When the radio is turned off the current speed display appears When the radio is turned on the current frequency is displayed If you do not perform any operation within 5 seconds the display returns to the current speed While presetting mode or deleting mode the current speed display will not appear After completing or canceling the presetting deleting mode the current speed display appears after 5 seconds
Download Pdf Manuals
Related Search