Sony CDP-C201 Operating Instructions
Contents
1. 4 Choose the selection 5 PROGRAM 12 To program additional selections from the same disc repeat steps 4 and 5 To program additional selections from another disc repeat steps 3 4 and 5 To start playing You can play up to 32 steps in the desired order You can program one selection or one disc in a step To program a whole disc e Using the DISC SKIP button After step 1 and 2 1 Press DISC SKIP button AL is displayed in the window 2 Press PROGRAM 3 Go on to step 6 e Using the DISC 1 to 5 buttons CDP C305 only After step 1 and 2 1 Press the DISC 1 to 5 button to select the disc 2 Go on to step 6 The whole disc is programmed as one step To program while observing the disc labels You can program the selections with the disc compartment open To check the programmed selections Press gt gt PPI in the pause mode Each time you press PP PPI the selections are displayed in the order they have been programmed To erase the last selection programmed Press W once to erase or correct the program To erase all the selections programmed Keep M pressed to erase or correct the program The program will be erased in the following situations e amp is pressed during program play e Power is turned off To display the total playing time of the program Press the TIME button after programming and before playing The time display will blink and2. The disc is set upside down Set the disc with the label side up oth disc is tilted Set the disc correctly The disc is extremely dirty Clean the disc DISC 1 tray Remote commander does not operate the p batteries are exhausted T Discs cannot be played continuously F Play did not start from the disc in the Press DISC 1 to start play Replace both batteries unit For CDP C305 only he remote commander is not pointed at Point the remote commander to the the remote control sensor sensor There is an obstacle between the remote Remove the obstacle commander and the unit Move closer Turn off the power and turn it on again The remote commander is too far from the unit Any operation is not possible The internal control program may not run Sony Corporation Printed in Japan
3. What is this indication E This indication appears while the player is shuffling L E the selections Playing Repeatedly Repeat Play REPEAT Press before or during play REPEAT REPEAT is displayed Scanning Selections Music Scan You can repeat a single disc or all the discs The unit repeats the current playing mode To cancel repeat play Press REPEAT again REPEAT disappears MUSIC SCAN Press during stop MUSIC SCAN gt blinks and each selection plays for approximately 12 seconds and fades out scanning play starts the next disc or selection for CDP C305 only You can check the selections by scanning the beginning of each selection on the disc You can use this function in any play mode To stop music scan play Press E Starting play at the selection being played during music scan Press i or B on the remote commander Selecting the ALL DISCS or 1 DISC in the continuous play e To scan the first selection of each disc select ALL DISCS e To scan the entire selections of a single disc select 1 DISC 11 Playing in a Desired Order Program Play You can make a program by designating up to 32 steps in the order you want them to be played The unit will play the disc according to your program PGM is displayed buttons only DISC 1 to 5 CDP C305
4. Power consumption 11 W Dimensions CDP C305 C205 C201 z B Approx 430x110x385 mm w h d 17 X 43 8 X 151 4 inches CDP C301M Approx 355 x 110385 mm w h d 14x 43 x 151 4 inches not including projecting parts and controls Weight CDP C305 C205 C201 Approx 4 9 kg 10 Ibs 13 02 net CDP C301M Approx 5 0 kg 11 Ibs net After playing store the disc in its case Supplied accessories Audio signal connecting cord phono plug x 2 s gt phono plug x 2 1 Remote commander 1 CDP C305 only R6 size AA batteries 2 CDP C305 only Operating Manual 1 Design and specifications subject to change without notice 15 Troubleshooting Guide The following checks will assist in the correction of most problems which you may encounter with your unit Should any problem persist after you have made these checks consult your nearest Sony service facility Before going through the check list below first refer back to the connection an operating procedures B Trouble Causes Remedy amp audio from one or both channels Incorrect operation of the amplifier Operate correctly Loose connection Connect the cords firmly _ Play does not begin No disc in the disc compartment Put disc s in the compartment Press 1 pm or El on the remote commander to release pause The player is in the pause mode Moisture condensation Leave the player turned on for about an hour
5. Be sure to set TIMER to OFF If the TIMER switch is left at PLAY the unit will automatically start playing the next time the power is turned on Maintenance Specifications Ci z th bi t System Compact disc digital audio system eaning e cabine Laser Semiconductor laser A 780 nm Emission duration continuous Clean the cabinet panel and controls with a soft cloth Laser output Max 44 6 pW lightly moistened with mild detergent solution Do not use This output is the value measured any type of abrasive pad scouring powder or solvent such at a distance of about 200 mm as alcohol or benzine from the objective lens surface on the Optical Pick up Block z Frequency response 2 Hz 20 kHz E13 a5 Cleaning discs Signal to noise ratio More than 93 dB Dynamic range More than 90 dB Before playing clean the disc with the cleaning cloth Harmonic distortion Less than 0 05 1 kHz Wipe the disc from the center out A Channel separation More than 90 dB 1 kHz Wow and flutter Below measurable limit Outputs LINE OUT phono jacks Output level 2 V at 50 kilohms Load impedance over 10 kilohms PHONES stereo phone jack CDP C305 C205 only Output level 0 10 mW variable at 32 ohms General r Power requirements Model for USA Do not use solvents such as benzine thinner 120 V AC 60 Hz commercially available cleaners or anti static spray Model for Australia CDP C305 only intended for analog discs 240 V AC 50 60 Hz
6. gt gt PPI AMS RMS manual search buttons 7 stop button 8 l play pause button 9 PROGRAM button 10 SHUFFLE button 11 CONTINUE button 12 TIME FADE button 13 REPEAT button 14 TIME button 15 Headphones LEVEL control 16 HEADPHONES jack Remote sensor AMS is the abbreviation of Automatic Music Sensor RMS is the abbreviation of Random Music Sensor CDP C301M POWER switch 2 TIME button 3 REPEAT button 4 TIME FADE button 5 CONTINUE button 6 SHUFFLE button 7 PROGRAM button 8 KO lt a gt gt PPI AMS RMS manual search buttons z 9 11 play pause button 10 stop button 11 OPEN CLOSE button 12 DISC SKIP button Display window Remote sensor Disc tray 16 TIMER switch Remote Commander CDP C305 only Refer to the pages indicated in for details 1 MUSIC SCAN button 2 REPEAT button DISC 1 5 buttons DISC SKIP button FADER button tta PI AMS buttons lt lt gt gt manual search buttons E stop button Il pause button gt play button TIME button CONTINUE button SHUFFLE button 14 PGM program button alsl eleleelels 4 Installing Batteries in the Remote Commander two size AA R6 batteries On battery life e About half a year
7. 3 00 Wi 37 00 min 30 00 min 27 00 min To set the second keep Ke lt gt PPI pressed The second can be set by 10 seconds shift 3 Press TIME FADE after setting the time The time display blinks quickly and disappears 4 Press PHI button to start the play Play starts to fade out five seconds before the time set and the unit enters the pause mode To cancel time fade Keep kea lt gt PPI on the unit pressed Press lt 4 lt 4 on the remote commander Press TIME FADE Fading in Fading out You can have the play fade in and fade out for 5 seconds for CDP C305 only To end the play fading out Press FADER when you want to start fading out Il blinks in the window and play fades out for 5 seconds and enters the pause mode To restart the play fading in Press FADER in the pause mode amp blinks in the window and play fades in for 5 seconds Timer Activated Playing Connecting cord To the switched outlet Keep the power on To the switched outlet Audio timer 14 for CDP C301M only This function can be operated in the continuous play mode 1 insert a disc in the compartment 2 Set the timer 3 Set TIMER to PLAY Keep the POWER switch depressed on the CD player When the timer is set the power of the player will be cut _ off At the time set the CD player will be switched on and play will start When the timer activated play ends
8. Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient the receiving antenna Relocate the equipment with respect to the receiver Move the equipment away from the receiver Plug the equipment into a different outlet so that equipment and receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Table of Contents Introduction introduction oonanenaonnooenooroososnoernsonsnsnsesrenosnsesnenrnesesess 3 Precautions 0 000 4 Installation 4 Connections 5 Location Of controls 00 0 0 cceeeseeseececeesneceseeeeee 6 F
9. SONY 3 751 430 21 2 Compact Disc Player Operating Instructions DIGITAL AUDIO CDP C305 CDPLC201 J 1990 by Sony Corporation Owner s Record The model and serial numbers are located at the rear Record these numbers in the spaces provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No Serial No To prevent fire or shock hazard do not expose the unit to rain or moisture CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance CAUTION The use of optical instruments with this product will increase eye hazard This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a
10. changes to give you the following information Elapsed time in a selection automatically displayed when play begins gt Remaining time in a selection indication will appear in the display window instead of the actual time if a selection numbered 21 or higher is selected Remaining time of the disc Notes Total remaining time is only available during continuous mode If will not be displayed by pressing the TIME button during program or shuffie mode Total remaining time will be displayed if time fade is set during program or shuffle Selecting a Desired Disc By using the DISC 1 to 5 buttons or the DISC SKIP button during play you can locate the beginning of any disc To select a particular disc for CDP C305 only To move to the disc tray next to the current one Locating a Particular Selection Press the corresponding DISC 1 to 5 button Press DISC SKIP button Locating a selection in sequence Automatic Music Sensor You can locate the beginning of a selection on the disc being played Press Kd lt 44 once Continue to press until the selection you want is located To locate the beginning of the selection being played To locate the beginning of the next selection Note for CDP C305 only You can operate this function on the remote commander Press lt P gt Pi Locating a Particular Point in a Selection L
11. each disc will be computed for the total programmed time After the addition has been completed the program time will be displayed for 3 seconds When other programs are added and the TIME button is pressed the program time of the added program only will be computed On the other hand if even one step is cleared it will compute from the beginning If selections numbered 21 or higher is programmed the indication will appear instead of numbers To stop program play Press W The last selection number programmed is displayed To resume play press I or on the remote commander Play begins from the beginning of the program You can play the same program repeatedly as long as you do not cancel program play or erase the program To cancel program play Press CONTINUE and return to the continuous playing mode The program will be erased 13 Tips on Editing Tapes The following functions are convenient for editing your own tapes Fading out after a desired duration Time Fade You can have the play fade out at the end by designating the play duration To set time fade 1 Press TIME FADE during stop and pause FADE is displayed and blinks in the window 2 Set the desired play duration using the Kd lt lt 4 bP PP i buttons Each time you press lt 4 lt gt PPI the display changes to give you the following duration press Kid lt q press D gt PPI on min ses 2
12. o a portion with very low level inputs or no audio signals If you do the speakers may be damaged when a peak level portion is played To listen with the headphones Connect the headphones and control the volume with the LEVEL control for CDP C305 C205 only Note on the TIMER switch Leave the TIMER switch off when not setting timer activated play for CDP C301M only Notes on handling discs e To keep the disc clean handle the disc by its edge Do not touch the surface e Do not stick paper or tape on the disc e Do not expose the disc to direct sunlight or heat sources such as hot air ducts or leave it in a car parked in direct sunlight as temperature may rise considerably e After playing store the disc in its case To play an 8 cm 3 inch CD Place it on the inner circle of the tray If the disc is Provided with an adaptor first remove it Do not put a normal CD 12 cm 5 inch on top of an 8 cm CD Notes 7 The tray number of an empty tray will be displayed until the empty tray number is set to play Once it is recognized as empty it will disappear e If there are no discs at all in the trays when played no disc will be indicated Information Display If you press press amp or the compartment itself to close the compartment the total number of selections and the total playing time of the disc to be played are displayed for a few seconds Each time you press TIME during play the display
13. ocating a point in sequence Manual Search You can locate a particular point in a selection during play by monitoring the high speed sound To go back at high speed Keep Iq lt 4 pressed To go ahead at high speed Keep gt PPI pressed Release the button when you reach the point in the selection you want Note for CDP C305 only You can operate this function on the remote commander Keep lt lt 4 PP pressed To locate at a higher speed Press kad lt lt or gt gt PPI in the pause mode Search speed will increase three times but there will be no sound Find the desired point by watching the numbers in the display Playing in a Random Order Shuffle Play Decide whether to shuffle between all discs or 2 one depending on the number of discs inserted To shuffle ALL DISCS press once To shuffle 1 DISC press twice SHUFFLE A 10 You can have the selections up to 99 played in a random order The unit will play all the discs or just one disc you desire Once a selection is played it will not be played again until the random order is completed To stop playing Press W To cancel shuffle play Press CONTINUE and return to the continuous playing mode To change from program or continuous play to shuffle play Press SHUFFLE during program or continuous play The program mode will be cleared and shuffle play will begin from the current selection being played
14. of normal operation can be expected when using the Sony SUM 3 NS batteries e When the batteries are run down the remote commander will not operate the unit In this case replace both batteries with new ones Notes on the remote commander and remote control operation Keep the commander away from extremely hot or humid places e Avoid dropping any foreign objects into the commander casing particularly when replacing the batteries e Avoid exposing the remote sensor to direct sunlight or lighting apparatus Such exposure can cause a malfunction e To avoid damage caused by battery leakage and corrosion remove the batteries when the commander will not be used for a long time Playing a Disc Before playing a disc turn on the amplifier and set the input selector to the CD player position To play more than one disc repeat step 3 to put additional discs in the desired order Choose whether to play 1 DISC or ALL DISCS CONTINUE Shows that Circle appears around tray No 6 the tray is occupied being played Selection gt I ri No 1 Elapsed playing time I tj I L To stop play To stop for a moment during play press PHI or Elon the remote commander Press again to resume play To stop play press W To stop play and open the tray press amp Caution on adjusting volume Do not turn up the volume while listening t
15. ront Panel oo cece ccsccseeseeteeseesteeeeeee 6 Remote commander 7 Installing batteries in the remote commander 7 Playing a GSC s2ococccc2es seeccsicess candies bensssedissnstescavsatodevevesedeet 8 Information display 20 cccceccesescessscsesssesseeceseeeeees 9 Selecting a desired disc oo 9 Locating a particular selection 9 Locating a particular point in a selection 0 00 0 9 Playing in a random order Shuffle play 10 Playing repeatedly Repeat play oo 11 Scanning selections Music scan 0 0 0 cccceeeeeeee 11 Playing in a desired order Program play 12 Tips on editing tapes 0 0 0 0 ec seeeeeeeeeeseees 14 Fading out after a desired duration Time fade 14 Fading in Fading out c cc ccsescsesseseeceesseseseesenens 14 Timer activated playing ccc ccsceseereecesseeseeeseeees 14 Maintenance 222i cseiceccceccescccectesseecksnsests adecdecsensivaivedessdacseae Cleaning the cabinet Cleaning diSCS 0 0 ceecesesecsseeeeessessseseeeeessesseeeesesees Specifications 0 00 00 Troubleshooting guide S This indicates a function operated only from the remote commander T This indicates a function operated only on the main unit 4 TIMES OVERSAMPLING DIGITAL FILTER compact disc player DUAL D A CONVERTER SYSTEM This unit is equipped with 5 disc trays which allow you to choose from a large number and wide varie
16. safe place When transporting the unit replace the key in its original hole and lock it in place CDP C305 C205 C201 CDP C301M Precautions On safety Check the unit s operating voltage before operation It must be identical with that of your local power supply e Should any liquid or solid object fall into the cabinet Unplug the unit and have it checked by qualified personnel before operating it any further Unplug the unit from the wall outlet if it will not be used for a long time To disconnect the cord pull it out by grasping the plug Never pull the cord itself e As the laser beam used in this compact disc player is harmful to the eyes do not attempt to disassemble the cabinet Refer servicing to qualified personne only On operation When the unit is not used turn the power off to conserve energy and to extend the useful life of your unit For detailed safety precautions see the leaflet IMPORTANT SAFEGUARDS If you have any questions or problems concerning your unit please contact you nearest Sony dealer Installation Placing Your Unit e Place the unit in a location with adequate air circulation to prevent internal heat buildup in the unit Do not place the unit on a soft surface such as a rug that would block the ventilation holes on the bottom e Do not install the unit near heat sources such as radiators or air ducts in a place subject to direc
17. t sunlight excessive dust mechanical vibration or shock Not this way On moisture condensation If the player is brought directly from a cold to a warm location or is placed in a very damp room moisture may condense on the lens inside the unit Should this occur the player will not operate In this case remove the disc and leave the player turned on for about an hour until the moisture evaporates e Turn off the power of each unit before making connections Connect the AC power cord last Be sure to insert the plugs firmly into the jacks Loose connection may cause hum and noise To Connect to an Amplifier For Correct Connections e Leave a little slack in the connecting cord to allow for inadvertent shock or vibration e Cord plugs and jacks are color coded Red plugs and jacks are for the right channel R and white ones for the left channel L To AC outlet lt CDP C305 C205 C201 C301M ESTATE serf Speaker system Location of Controls CDP C305 C205 C201 2 Front Panel CDP C301M 12 11 10 L9 8 7 6 16 Refer to the pages indicated in for details CDP C305 C205 C201 POWER switch 2 Disc tray 3 4 OPEN CLOSE button Display window 5 DISC SKIP button 6 e lt
18. ty of selections Any disc at any time can be played using the DISC 1 to 5 buttons CDP C305 only e Shuffle play page 10 Once a selection is played it will not be played once more until the random order is completed e Music scan page 11 You can check the selections by scanning the beginning of each selection CDP C305 only e Program play page 12 Up to 32 steps of program is possible from the 5 discs e Time fade page 14 You can stop the play fading out at the time desired e Fading in Fading out page 14 You can begin a selection fading in and end it fading out CDP C305 only Differences by Model and Area This instruction manual covers CDP C305 CDP C205 CDP C201 and CDP C301M Their performance and operation are identical except for the following The CDP C205 C201 and CDP C301M are not supplied with a remote commander They do not have those functions activated only by remote commander which are indicated with I mark in this instruction manual e The CDP C201 and CDP C301M do not have a PHONES headphones jack and a LEVEL control The CDP C301M only have a TIMER switch The illustrations used in this manual are of the CDP C305 Note on the Transit Key The white transit key on the bottom exterior of the unit protects the optical system against shock during transportation Before operating the CD player be sure to remove the key by following the instructions on the label and store it in a
Download Pdf Manuals
Related Search