Sonic Alert DB100 User's Manual
Contents
1. Sonic Alert America s Leader in Visual Alerting Systems WIRELESS DOORBELL SIGNALER MODEL DB100 SONIC ALERT S 5 YEAR LIMITED WARRANTY The Wireless Doorbell Signaler Model DB100 is warranted against manufacturing defects in materials and workmanship for five 5 years from the date of purchase Within this period Sonic Alert will replace at our option the DB100 without charge for parts and labor Simply send the DB100 postpaid and a copy of your sales slip as proof of purchase to Sonic Alert Inc 1050 E Maple Road Troy MI 48083 Operation The state of the art Doorbell Signaler will alert you when someone comes to visit The DB100 is the only doorbell signaler that does not require wires and can be installed in seconds DB100 signaler will alert you that someone is at your door by flashing a light plugged into it and any other Sonic Alert remote receivers you may have The DB100 is designed to work in homes with or without an existing doorbell or chime Selecting Flash Rate Other features include a selectable number of flashes 5 or 10 and different flash code for front door rear door or intercom Additional sensors DB100T sold separately can be used for 2 door There is also a built in chime for hearing members of the family The DB100 receives an RF radio signal from the DB sensor and flashes the light plugged into the built in outlet of the signaler Use a 300 watt or less incandescent lamp only The signaler2. can send a signal to all Sonic Alert remote receivers Note Must be used only with Sonic Alert receivers for proper operation Other manufacturers products are not reliable with our products DB100 Signaler DB Sensor INSTALLATION To install the DB100 follow the diagrams and instructions on the following page that match the type of installation you need for your home If the installation follows diagram 1 a 12 volt alkaline battery is required in the DB sensor Please check the switches on your DB Sensor before installing Do not change switches 1 6 These are pre set Setting the Dip Switches DB Sensor settings smaller unit for dip switches 1 thru 6 are set at the factory and only need to be changed if your neighbor has a DB100 or DB200 The 8 dip switches should be set as follows a 1 thru 3 dip switches are set in the ON position and 4 thru 6 are set in the OFF position If you need to change the dip switch settings to avoid interference with your neighbors make sure you change the DB100 Signaler to match the DB Sensor b The 7 switch is for when you are using 2 sensors this switch determines the settings for front or back door If using for one door only set this switch in the ON position At this setting your unit will flash at a fast rate and will make a ding dong sound If using 2 sensors one for the front door and one for the back door the setting for the 2 sensor would be in the OFF position In this
3. of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications not expressively approved by the party responsible for compliance could void user s authority to operate the equipment
4. position the front door will flash at a different flash rate than the back door In the OFF position your back door sensor will flash at a slow rate with a ding dong sound c The 8 switch determines the number of flashes when someone is at your door In the ON position your unit will flash 5 times and in the OFF position your unit will flash 10 times This feature 1s wonderful when you have an extra sensor for the back door One sensor would be set in the ON position and the other would be set in the OFF position Setting the Audio Switch Top OFF Bottom ON Located on the DB100 Signaler larger unit The speaker switch allows you to turn the Audio Alarm ON or OFF ON is down and OFF is up Multi Function Input Jack Located on the right side of the DB Sensor this input jack 1s for installations as shown below in diagram 2 amp 3 DB100 INSTALLATION DIAGRAMS 1 Wireless Installation 2 Wired Doorbell Installation 1 Attach sensor to 1 Connect doorbell outside of door button to sensor 2 Plug signaler into with provided wall outlet ___ wire 3 Plug lamp into 2 Plug signaler into signaler aA wall outlet 3 Plug lamp into signaler 1 Wire sensor into chime for battery less operation 2 Plug signaler into 4 wall outlet 3 Plug lamp into signaler Battery free installation diagram 3 Use wire provided plug into jack outlet on side of Transmitter Remove chime cover and conne
5. ct the red and yellow wires to chime box terminal screws common and front Troubleshooting amp Help If you ve followed the directions and are still having problems please try the following suggestions 1 Check battery in the sensor Must be a 12 volt alkaline type 2 Check dip switch settings Both the sensor and the signaler must match as shown in figure 1 1 above 3 Check outlet for power 4 Move the Signaler to an outlet closer to the sensor unit 5 If using the Multi Function input jack make sure that the wires are not touching each other See diagram number 2 amp 3 for proper installation 6 Check that sensor is not further than 50 feet from the receiver 7 Do not place sensor on steel doors or steel door frames For Technical help call 1 248 577 5400 M F 8 00 a m 5 00 p m Eastern Time Or e mail us with your questions at sonic info sonicalert com Warranty Thank you for purchasing this high quality Sonic Alert product We hope you will have many years of satisfied use This Sonic Alert product comes with a limited 5 year warranty so please retain your receipt in a safe place for possible future reference you will need in the event of warranty service Sonic Alert Inc 1050 East Maple Rd Troy MI 48083 V TTY 1 248 577 5400 fax 248 577 5433 E mail sonic info sonicalert com Web Site www SonicAlert com REV 1 5 2008 This device complies with Part 15 of the FCC Rules and with RSS 210
Download Pdf Manuals
Related Search