Soleus Air PE6-10R-03 User's Manual
Contents
1. Press the A or V buttons to change the timer to the desired amount of time 1 24 hours for the unit to automatically turn on 8 Sleep Mode Sleep mode is not available on this model 12 CE MAINTENANCE Note Make sure power is off and the power cord is not plugged into an electrical outlet prior to performing any maintenance on the unit Clean or replace filter If the air filter 1s blocked with a dust the airflow volume may reduce It is recommended to clean the filter once every two weeks or as needed 1 Remove the filter from the filter compartment on the back of the unit 2 Wash the air filter by immersing it gently into warm water with a neutral detergent Rinse the filter and dry it thoroughly out of sunlight 3 Slide the filter back into the filter compartment after it is thoroughly dried 4 Ifthe filter is torn or unusable order a new filter by calling the customer service number on the watranty page of this manual Clean the unit Housing 1 Keep the unit from being exposed directly to the sun to prevent color fading 2 Clean the surface with a damp cloth and dry it with a soft towel Storing the Unit for an Extended Period of Time or Transporting the unit 1 Empty any excess water by unplugging the water drainage stop in the back of the unit located at the bottom 2 Unplug the unit 3 The unit should be stored in a cool dry place 13 ee WARRANTY One Year Limited Warranty Soleus Internatio2. S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT This warranty covers only new products purchased from our authorized dealers or retailers It does not cover used sal vaged or refurbished products As some states do not allow the limitation or exclusion of incidental or consequential damages or do not allow limitation on implied warranties the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state For Technical Support and Warranty Service Please Call 888 876 5387 Or Write To Soleus International Inc 20035 E Walnut Dr N City of Industry CA 91789 www soleusair com 14
3. of the unit e Ifthe environment temperature is higher than the max operating temperature or lower than the minimum operating temperature the air conditioner may not work properly Rated Current 9 3 Amps sound Pressure Level 45 dB A Product Weight 96 2 Ibs Product Dimensions W x D x H 11 75 W x 18 75 D x 24 875 H Refrigerant DISCLAIMER ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER S MANUAL ARE THE PRESENTATION OF THE MANUFACTURER SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN PRODUCT DIAGRAM NOTE Actual product design may differ slightly from images below FRONT A Control panel B Vertical air louvers C Air outlet D Horizontal air louvers E Casters F Power Cord amp Plug BACK A Hot air outlet grill B Lower air inlet grill ACCESSORIES Flexible exhaust hose with 2 adapters e 3 piece set e stretches from 14 1 4 to 60 5 8 36cm to 150cm Adjustable window slider kit e 3 piece set e adjusts 19 7 55 5 50cm to 141cm Drain tube A B _ ST Ly i A F we ee i N VN NW NN WAN W w poi Adapter qaen pee a Adjustable Window Slider Kit INSTALLATION SELECTING THE LOCATION Place the unit in a flat location where the air out lets are not obstruc
4. the drain pan as it might easily overflow SCREW PLUG DRAIN HOLE 11 OPERATING THE UNIT USING THE REMOTE CONTROL REMOTE CONTROL TIMER TEMP INCREASE SWING LOUVER MODE BUTTON OSCILLATION F C FAN SPEED TIMER BUTTON SLEEP MODE not available on this model TIMER TEMP DECREASE POWER BUTTON 1 Power On and Off Press the ON OFF button on the remote to turn the unit on or off 2 Mode Selection Press the MODE Button repeatedly to cycle between the different modes Air Condi tioner and Dehumidifier 3 Fan Speed Press the FAN speed button to cycle through low and high fan speeds 4 Temperature Setting When the unit is in Air Conditioner mode you can select your desired tempera ture Press the A or V to select your desired temperature setting The temperature on the multi color display on the control panel will increase or decrease accordingly Pressing the F C button will change the temperature select between F and C 5 Swing To turn on oscillation press the SWING button on the remote control Once you press SWING the louvers on the unit will oscillate side to side 6 Auto on Timer To program the Auto on timer press the TIMER button when the unit is powered off Press the A or V buttons to change the timer to the desired amount of time 1 24 hours for the unit to automatically turn on 7 Auto off Timer To program the Auto off Timer press the TIMER button when the unit is powered on
5. the unit will cool the room most efficiently by setting the temperature at the lowest setting and the fan speed on high Reducing the length of the exhaust duct insulating the exhaust hose and window kit and keeping direct sunlight to a minimum will also improve the cooling efficiency NOTE When the unit is running on cooling mode the exhaust hoses are required and must be vented outside using the supplied window kit Dehumidifier Mode 1 Install the exhaust hoses and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the POWER Button on the control panel NOTE The unit operates at low fan speed during dehumidifier mode The unit cools room slightly during the dehumidification Keep the windows and doors closed to aid the effectiveness of the unit in removing the moisture from the room NOTE When the unit is running in dehumidifier mode the exhaust hoses are required and must be vented outside using the supplied window kit The unit will not perform in dehumidifier mode when the room tem perature is lower than 61 F Compressor Indicator The compressor light will light up on the control panel display when the compressor turns on The compressor light will turn off when the compressor shuts off CONDENSATE EVAPORATION E Emergency Condensate Holding Tank When the room temperature is low and the indoor humidity is high the air conditioner may not be able t
6. SOLEUSAIR Portable Air Conditioner with Evaporative Technology PE6 10R 03 Operating Instructions LigteD Intertek 3046364 Model No PE6 10R 03 2011Soleus Air International Thank you for choosing a Soleus Air Portable Air Conditioner This owner s manual will provide you with valuable information necessary for the proper care and maintenance of your new product Please take a few moments to thoroughly read the instructions and familiarize yourself with all the opera tional aspects of your new Soleus Air Portable Air Conditioner with Heat Pump technology For your own records please attach a copy of your sales receipt to this manual Also write the store name location date purchased and serial number below Store Name Location Date Purchased Serial Number located on back of unit iis S SSS IMPORTANT INSTRUCTIONS Before installing and using your portable air conditioner please read this owner s manual carefully Store this manual in a safe place for future reference 1 Always place the unit on a level surface 2 Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual 3 Maintain at least 10 inches 25 cm clearance space around this unit Do not block or cover air inlet or outlet grilles 4 The unit must be connected to a correctly grounded power supply 5 Do not start or stop the unit by inserting or pulling out the power
7. adjust the length of the window kit to fit the opening figure d If necessary mark the kit and cut one end down to properly fit the opening figures e amp f Attach the window kit adapter to the window kit figure g Place the window kit back into the window and attach the exhaust hose to the window kit adapter figures h amp i Close the window tightly figure j Your Portable Air Conditioner is now ready to cool NOTE When using the venting system keep the exhaust hose as straight as possible The exhaust hose can be shortened but it is not recommended to increase the length of the exhaust hose Do not use an extension cord with your portable air conditioner show general directions for all Soleus Air single hose portable air conditioners CONTROL PANEL amp OPERATION 1 2 3 4 5 6 7 O COMPRESSOR FULL Ove OQ DEHUMIDIFIER Power On and Off Press the POWER button once to manually turn the unit on Press the POWER button once more to turn the unit off Mode Selection Press the MODE Button repeatedly to cycle between the different modes Air Conditioner and Dehumidifier Fan Speed Control Press the FAN Button to cycle through the different fan speeds High and low Temperature Select the desired temperature by pressing either V or A button when using the unit in cooling mode The temperature indicator flashes to display the desired temperature setting After the t
8. anel of the window kit if neces Maximum 55 5 141cm sary Place the window kit between the window and the window frame as shown in the images to the right Close the window onto the window kit to form a tight seal VERTICAL WINDOW Attach the exhaust duct adapter to the window kit Tabs located on the adapter will lock into place securing the adapter to the window kit Window Slider Kit Minimum 19 7 50cm Maximum 55 5 141cm WINDOW KIT INSTALLATION SOLEUSAIR Installation of the Venting Kit Innovative products for a cleaner FOR SINGLE HOSE PORTABLE AIR CONDITIONERS NOTE The Portable Air Conditioner above may differ from the unit described in this manual The above directions and images 1 more comfortable world The venting kit must be installed in order for the unit to work correctly in the air conditioning mode The venting kit should not be used while the unit is heating or fanning The window kit has been designed to fit into most vertical and horizontal window openings The window kit can also be used in a sliding door Choose a suitable location near a grounded electrical outlet and a suitable window or door Remove packaging and locate components figure a Slide the exhaust connector over the discharge opening on the back of the unit figure b Connect the exhaust hose to the exhaust connector aligning the fitted grove figure c Open the window or door and
9. eld must not be connected to ground or to any exposed metal The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly To test 1 Plug power cord into wall outlet 2 Press TEST Button circuit should trip cutting power to the air conditioner 3 Press RESET button for use If test button 1s pressed and unit can still be turned on current leakage has been detected Do not use the air conditioner or attempt to reset the LCDI Plug Contact Soleus Air Customer Service for troubleshooting recommendations RESET TEST WARNING 1 DO NOT press the TEST button while the air conditioner is operating 2 The TEST and RESET buttons should not be used as ON and OFF switches 3 The cord and plug are not intended to offer protection to externally connected loads or supply circuits 4 The cord and plug are intended for indoor use only WINDOW KIT INSTALLATION HORIZONTAL WINDOW WINDOW KIT INSTALLATION The window kit is designed to fit into most standard vertical and horizontal windows as well as some sliding glass doors However it may be necessary to modify some aspects of the installation process for certain window types Open the window or sliding door and adjust the length of the window kit to fit the opening If the window kit is not long enough connect the extra Window Slider Kit window kit panel to fit the opening Mark and cut Minimum 19 7 50cm down a single p
10. em perature is set the unit will display this temperature setting until it is changed by the user Press the VW and A buttons simultaneously on the control panel to change between Celsius or Fahrenheit Auto on Timer To program the Auto on timer press the TIMER button when the unit is powered off Press the A or V buttons to change the timer to the desired amount of time 1 24 hours for the unit to automatically turn on Auto off Timer To program the Auto off Timer press the TIMER button when the unit is powered on Press the A or V buttons to change the timer to the desired amount of time 1 24 hours for the unit to automatically turn on Swing To start side to side louver oscillation press the Swing button once The SWING light will light up on the control panel To stop oscillation press the Swing button again Vertical air flow direction can be adjusted manually NOTE HEAT MODE is not available on this model MODE OPERATION eC OPERATING THE UNIT USING THE CONTROL PANEL Air Conditioner Mode 1 Install the exhaust hose and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the POWER button on the control panel 4 Press the A or V buttons until the desired room temperature appears on the control panel display The temperature ranges from 61F 88 F 16 Cesi 5 Select the desired fan speed by pressing the FAN button NOTE During hot days
11. nal Inc warrants the accompanying Soleus Air Portable Air Conditioner to be free of defects in mate rial and workmanship for the applications specified in its operation instruction for a period of ONE 1 year from the date of original retail purchase in the United States If the unit exhibits a defect in normal use Soleus International Inc will at its option either repair or replace it free of charge within a reasonable time after the unit is returned during the warranty period As acondition to any warranty service obligation the consumer must present this Warranty Certificate along with a copy of the original purchase invoice THIS WARRANTY DOES NOT COVER e Damage accidental or otherwise to the unit while in the possession of a consumer not caused by a defect in material or workmanship e Damage caused by consumer misuse tampering or failure to follow the care and special handling provisions in the instructions e Damage to the finish of the case or other appearance parts caused by wear e Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus Interna tional Inc e Freight and Insurance cost for the warranty service ALL WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO ONE YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY SOLEUS INTERNATIONAL INC DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT SHALL SOLEUS INTERNATIONAL INC
12. o evaporate some of the moisture fast enough When this happens the water will accumulate in an emergency condensate tank inside the unit Once the emergency condensate tank is full the unit will automatically shut off and the FULL light will appear on the control panel display To empty the condensate tank unscrew the screw plug at the bottom back of the unit You will need a small pan approximately 1 high to catch the water coming out of the condensate tank Once the condensate tank is drained the unit will begin working within a few minutes The emergency condensate tank holds approximately 1 5 Liters of water Another option is to purchase a small hose from a hardware store that can fit around the 5 8 drain plug on the back of the unit and drain the unit into a gravity drain or larger pan for continuous drainage To resume operation quickly empty the water container according to the following steps 1 Turn the unit off Do not move the unit when the water container is full 2 Place the drain pan accessory under the drainage port at the back of the unit 3 Remove the screw plug from the drain hole The condensate water will drain out automatically When the drain pan is full screw the screw plug back onto the drainage hole to stop the water flow Empty the drain pan Repeat until all the water is emptied Once the water container has been emptied screw the plug back onto the drain hole Do not allow the water to drip continuously into
13. plug 6 Do not use an adapter plug or extension cord 7 Do not use the unit in the immediate surroundings of a bath a shower or a swimming pool 8 Do not insert anything into the air outlet Do not obstruct air inlet or outlet grills unless instructed by this manual 9 Do not let children play near this unit 10 Always inspect the cord for signs of damage before use If the power cord is damaged it must be replaced by the manufacturer or a qualified service technician 11 When cleaning the unit always turn the unit off and unplug the power cord 12 When the unit is not in use always remove the venting kit from window 13 Do Not Mix Old And New Batteries Do Not Mix Alkaline Standard Carbon Zinc Or Rechargeable Nickel Cadmium Batteries PACKAGE CONTENTS amp SPECIFICATIONS La What s in the Box Portable Air Conditioner Exhaust Hoses 1 Hose Adapters 1 Window Kit Adapter 1 Remote Control AAA Batteries 2 Window Kit 3 Sliding Panels 1 single hose panel 2 extension panels Owner s Manual ey SPECIFICATIONS e The cooling capacity is measured at an ambient temperature of DB 86 F WB 78 F e Noise level is measured at a distance of 3 28 ft away from the front of the unit when the unit is in cooling mode e Power consumption is measured when the fan runs at the highest speed setting e These specifications are for reference only For actual data please refer to the rating label on the back
14. ted Place the unit at least 20 50cm away from a wall or other obstacle MOUNTING THE EXHAUST HOSE Slide the square end of the exhaust duct over the hot air outlet on the back of the unit The exhaust hose should be kept as short and straight as possible Prevent any sharp bends in the exhaust hose as this will trap hot exhaust air The hot exhaust air can be vented through the wall or out a window If mounting in the wall the height of the hole should be 14 1 4 to 60 5 8 36cm to 150cm Soleus Air does not provide a venting kit for through the wall ventilation Venting through the wall requires a custom installation LCDI POWER CORD AND PLUG E This air conditioner is equipped with an LCDI Leakage Current Detection and Interruption power cord and plug as required by US National Electric Code 440 65 This cord consists of a length of shielded flexible cord with no termination on the load side and a LCDI attachment plug on the line side The LCDI power cord and plug will remove the supply source via electrical disconnect circuit trip if the nominal current leakage between the cord shield and either load conductor exceeds a predetermined value The cord will remain de energized until the devise has been manually reset This is intended to reduce the risk of a fire in the power cord or combustible materials nearby The cord shields are not grounded and they must be considered a shock hazards if exposed The cord shi
Download Pdf Manuals
Related Search