SmartLabs 2476D User's Manual
Contents
1. Quick Start Guide SwitchLinc Dimmer INSTEON Remote Control Dimmer Model 2476D 600 Watt Rev 5 0 Your new SwitchLinc Dimmer allows you to dim and remotely control any light in your home at the touch of a button Preparation Installation should be performed only by a qualified electrician or by a homeowner who is familiar and comfortable with electrical circuitry If you have any questions regarding installation we suggest consulting an electrician Software such as HouseLinc 2 can make management and setup of INSTEON devices much easier If you have any questions regarding setup contact Smarthome Tech Support Tools Needed e Phillips screwdriver e Wire cutter stripper Voltage tester to identify wires inside the junction box Installation SwitchLinc Typical 2 Way Circuit Note For Multi Way Circuit installation refer to the Owner s Manual 1 At the circuit breaker or fuse panel disable the circuit supplying power to the switch 2 Remove the faceplate from the existing switch then unscrew the switch and pull it out from the junction box 3 Disconnect the wires from the switch you are replacing and ensure you have 1 2 of bare wire on the ends 4 Tocorrectly identify the LINE LOAD NEUTRAL and GROUND wires enable power to the switch from the circuit breaker or fuse panel use a line voltage meter then turn the breaker off again See Figure 1 to properly connect your wires to SwitchLinc Not2. button pe Wiring Diagram Home s wire colors may vary Neutral Usually White Y Line Usually Black Load g Usually black EFA red or blue y t Ero Ground Usually Copper or Green Ground Copper Figure 1 Using SwitchLinc as a Responder 1 Select your INSTEON compatible Controller and activate its Linking Mode You will have 4 minutes to complete the next step 2 Press amp hold the paddle top on SwitchLinc until the unit double beeps about 10 seconds The SwitchLinc top LED will flash and then turn on solid and the controlled light will flash 3 Confirm the Link by tapping the On Off buttons on the Controller you just Linked to SwitchLinc SwitchLinc should respond appropriately Complete Instructions Troubleshooting and Tech Support Owner s Manual http wiki smarthome com index php title 2476D_Manual Call Tech Support 1 800 SMARTHOME 800 762 7846 Contact Us Online htto www smarthome com contactus html ETL UL Warning CAUTION To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle a motor operated appliance a fluorescent lighting fixture or a transformer supplied appliance Gradateurs commandant une lampe a filament de tungstene afin de reduire le risque de surchauffe et la possibilite d endommagement a d autres materiels ne pas installer pour commander une prise un appareil a mot
3. e Mechanical switches don t utilize NEUTRAL but they are usually available in the back of the switch box 5 Ensure that all wire connectors are firmly attached and that there is no exposed copper except for the GROUND wire 6 Orient SwitchLinc with the LED bar at the left gently place it into the junction box and then screw it into place 7 Enable power to the fixture from the circuit breaker or fuse panel 8 Test that the SwitchLinc is working properly by turning the light on and off 9 Reinstall the faceplate Using SwitchLinc Tap the paddle top to turn your light on Tap the paddle bottom to turn your light off Press amp hold the paddle top to brighten your light Press amp hold the paddle bottom to dim your light Double tap the paddle top to turn your light to full on quickly Double tap the paddle bottom to turn your light off quickly Using SwitchLinc as a Controller 1 Press amp hold paddle top until the unit beeps about 10 seconds The top LED will begin blinking and the controlled light will flash once You will have 4 minutes to complete the next step 2 Select the INSTEON device you would like to control and activate its Linking Mode SwitchLinc will double beep and its LED will stop blinking and turn on solid and the controlled light will flash once 3 Confirm the Link by tapping the SwitchLinc paddle on and off The device SwitchLinc is controlling should respond appropriately LED bar Paddle bottom Set
4. eur une lampe flourescente ou un appareil alimente par un transformateur SmartLabs Limited Warranty SmartLabs warrants to original consumer of this product for a period of 2 years from date of purchase this product will be Page 1 of 1 Rev 01 06 2010 misuse or neglect U S Patent No 7 345 998 International patents pending Copyright 2010 SmartLabs 16542 Millikan Ave Irvine CA 92606 1 800 SMARTHOME 800 762 7846 free from defects in material amp workmanship amp will perform in substantial conformity with its Owner s Manual Warranty shall not apply to defects caused by smart
Download Pdf Manuals
Related Search