SkyLink TM-434-2 User's Manual
Contents
1. the instructions below to transmit the Learn code to the receiver 1 Put the receiver module that you plan to program into programming mode Refer to the User s Instructions of that receiver module 2 Remove the battery and battery holder from the Mini Remote 1 Unlock e e 2 Remove battery holder 3 Insert the battery and battery holder to the Mini Remote its red LED will stay on for 15 seconds Press the button on the remote that you plan to use when the LED is steadily on to transmit the Learn code S LED O Press the button while the LED is ON steadily RA Q Insert battery holder 4 Once the remote is programmed the receiver modules will quit from Positive sideup programming mode and the programmed transmitter is ready to be used now 3 PROGRAMMING TRANSMITTERS TO RECEIVER MODULE CONT Learn Code Follow steps 2 and 3 above to transmit the Learn code when programming the Mini Remote to receiver modules Note Once the receiver is in programming mode you have to finish the programming as soon as possible It will quit from programming mode after 15 sec even if you have not finished the programming You may have to start it over again 4 ON OFF OPERATION Pressing the button on the remote once will toggle the status of the load that is connected to the receiver module i e if the light is off pressing the button turns on the light and vice versa 5 BRIGHTNESS CONTROL OPERATION Besides t2. Mini Remote Model TM 434 2 1 INTRODUCTION Thank you for your purchase of a SkylinkHome Mini Remote Model TM 434 2 This transmitter allows you to wirelessly operate lighting home automation with the SkylinkHome receiver modules The Mini Remote can work with all the SkylinkHome receiver modules even though it is specifically designed for mounting onto either Wireless Wall Dimmer Model WR 001 or On Off Wall Switch WE 001 All wireless signal communications within the SkylinkHome System are based on rolling code technology to provide added security You will find the following in this package Mini Remote Lithium Battery CR 2032 Installed User s Instructions Red LED p Buttons o 2 Mini Remote TM 434 2 S Battery and battery holder 2 POWER UP To power the transmitter simply remove the battery isolator from the transmitter red LED will stay on for 15 seconds and then off Press the button on the transmitter the red LED should flash The transmitter is now powered properly If the red LED does not flash when button is pressed refer to Section 7 Battery of this manual D LED on for 1 second Remove Isolator 3 PROGRAMMING TRANSMITTERS TO RECEIVER MODULE In order to remotely control lighting home automation connected to receiver a transmitter must be programmed to the receiver module To program a Mini Remote to the receiver module a Learn code must be transmitted follow
3. he receiver 1 Remove the battery and battery holder from the Mini Remote 2 Insert the battery and battery holder to the Mini Remote its red LED will stay on for 15 seconds Press and hold the button on the remote for at least 2 seconds when the LED is steadily on to transmit the Erase code Do not release this button until step 4 3 Put the receiver that you want to erase the transmitter from into programming mode Refer to the User s Instructions of that receiver D Once the receiver receives this Erase code the receiver will indicate it has erased all transmitters and you may now release the button on the Mini Remote Erase Code Follow steps 2 and 3 above to transmit the Erase code when erasing the Mini Remote from Type B receivers 7 BATTERY When the operating range is reduced or when the red LED does not flash during operation it is time to replace the battery Follow the same procedure as installing the battery in section 3 of this manual to replace the battery CAUTION Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility EN 300220 2 EN301489 3 EN61058 1 EN503771 This equipment conforms to the essential requirement of the Directive 1999 5 EC of the European Parliament and of the Council 9 WARRANTY If within
4. one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 10 CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com CE X CUSTOMER SERVICE Rm 1303 Block B Veristrong Industrial Centre 36 Aupuiwan Street Fotan N T Hong Kong Email sales skylinkhome com http www skylinkhome com P N 101Z004 001 2010 SKYLINK GROUP 11 ACCESSORIES The SkylinkHome System consists of many other devices such as SkylinkPad Remotes Motion Sensor ON OFF Wall Switch Wall Dimmer Plug In Dimmer with or without Repeater Plug In ON OFF Control Screw In Dimmer ON OFF Dimming Control ON OFF Control Smart Button Garage Door Control etc Please visit Skylink website at www skylinkhome com for more information
5. urning on and off the light you may also control the brightness of the light if the receiver module and the light bulb is dimmable i e either incandescent light and dimmable compact fluorescent light connected to a dimmer To change the brightness first turn on the light Then press and hold the button on the Mini Remote to change the brightness Hold the button until the desired brightness is reached then release the button Press and hold the button again to change the brightness again in the opposite way When the desired brightness is reached then release the button 6 ERASING TRANSMITTERS There are 2 types of receivers and erasing transmitter from these 2 types of receivers are different Please follow the erase procedure based on the receiver you have Type A Self Erase Model EE 434 ER 434 PA 434 PL 434 PR 434 PR 434S WE 434 WR 434 Self Erase means there is a erase button on the receiver by pressing this erase button all transmitters can be erased To erase transmitters from these receivers simply follow the instructions of these receivers The erase procedure does not involve the transmitter Type B Erase by Remote Model LX 434 MD 434 MR 434 Erase by Remote means there is no erase button on the receiver so a programmed transmitter is needed in order to erase the memory of the receiver You need to transmit a Erase code from the Mini Remote Follow the instructions below to erase the remote from t
Download Pdf Manuals
Related Search