SkyLink TD-434 User's Manual
Contents
1. LCD Deluxe Remote Model TD 434 User s Manual CONTENT INTRODUCTION nenne dl 2 POWER UP aia 3 SET THE CLOCK u ame 3 PROGRAMMING THE LCD DELUXE REMOTE TO REGEIVER GONTROL ci ales niente 4 5 PROGRAMMING FOR INDIVIDUAL 5 6 PROGRAMMING FOR ZONE 6 7 PROGRAMMING FOR SCENE 7 9 PROGRAMMING FOR TIMER 9 12 BATTERY cesses Us os 12 TN 12 WARRANTY isos acia 13 CUSTOMER SERVICE 13 INTRODUCTION SkylinkHome LCD Deluxe Remote allows you to wirelessly operate SkylinkHome various wireless receiver controls This LCD Deluxe Remote provides features such as Zone Operation Scene Operation Timer Operation You can control various home appliances or lights with this remote control and different receiver units Applications include lighting ON OFF and dimming gate or garage door control arm and disarm your security system controlling a fan etc The following items are included in this package One LCD Deluxe Remote Two AAA batteries User s Instructions LCD Deluxe Remote Layout POWER UP Insert 2 AAA batteries to the remote with the correct polarity as shown its LCD display will turn on and red LED will flash once Press the button on the remote the red LED should flash2. The remote is now powered properly Ifthe LCD display does not turn on or red LED does not flash when button is pressed refer to Section Battery of this manual for details Follow the rest of the steps to setup the LCD Deluxe Remote so it can work with the receivers that you have SET THE CLOCK During the standby mode the LCD display will show the week and clock The clock is in 24 hours format To set the clock 1 Press the PROG button twice until you see the Settings icon and the day of the week flashing 2 Use the Up 4 Down W buttons to select the day of the week 3 Use the Left lt 4 or Right gt button to select the hour and minute and use Up A Down buttons to set the time 4 You can cycle between day of the week hour and minute with the left and right button 5 Press 5 to confirm the settings PROGRAMMING THE LCD DELUXE REMOTE TO RECEIVER CONTROL In order to operate the receiver control with this LCD Deluxe Remote it must be programmed to the receiver control The LCD Deluxe Remote can transmit 4 types of command 1 Individual Operation Control one light only i e the ceiling light in the family room 2 Zone Operation Controls one specific zone or area which consists of multiple lights i e all lights in the kitchen 3 Scene Operation Allow you to set specific atmosphere where each light has a preset brightness and the scene may consist of multiple lights
3. Learn code is sent 4 Once the remote is programmed the receiver control will quit from programming mode and the programmed remote is ready to be used now Follow the same instructions above to program the zone number into various receiver controls to form a zone with multiple lights i e Zone 1 signal to both Family Room Ceiling Light receiver control and Family Room Floor Light receiver control Zone Operation To turn on a zone 1 Press the Function button E 3 times 2 Press 1 9 to select the desired zone i e Enter 1 for Zone 1 and all the lights in Zone 1 will be on To turn off a zone 1 Press the Function button 4 times 2 Press 1 9 to turn off the zone e Enter 1 to turn off all the lights in Zone PROGRAMMING FOR SCENE OPERATION Scene can provide specific brightness of multiple lights with a press of a button this can create specific atmosphere The remote provides 9 different scene settings brightness of light control from 0 off to 100 brightest i e common scenes are morning scene evening scene movie scene and etc To setup a scene SCENE ri Cy Cite Li LILI Press the PROG button 4 times to enter the Scene Programming mode Press 1 9 to select the scene number you would like to program Use the Up 2 or Down 8 button to increment or decrement the brightness from 0 to 100 For instant select 60 brightness for your setting Once you selected the s
4. timer to start Press 5 to confirm the setting Press the PROG once to quit from programming mode or leave it on for 15 seconds The remote will return to normal standby mode After setting up the time and day you need to assign this timer to an action i e turn on a specific light Following table is an example you may assign the Timer to effective the action at a specific time and day of week Timer Button Event Time and Day of week Lights Action 1 Wake up MO TU WE TH FR Zone 3 Bed Turn On Timer 6 30 room all lights Zone 3 2 Weekend SA SU Zone 3 Bed Turn On Wake up 10 00 room all lights Zone 3 SA SU 3 Morning SU MO TU WE TH Zone 5 Front Turn On Outdoor Off FR SA 7 00 Back Yard Zone 5 SA SU EN Pool Off 22 00 Pool Light Off Light 6 SEN 0 3k H 1 1 H 1 1 oF 00 E a 11 E 111 To Assign a Timer 1 Press TIMER button once to select Timer mode 2 Press 1 9 to select the desired timer i e Enter 1 for Timer 1 3 Press PROG to select between assigning this timer for a Individual Light Device b Zone c Scene You can press PROG multiple times until the desired setting 4 Use the Up 2 Down 8 Button to select the Device Number Zone Number Scene Number 1 9 that you want the timer to activate 5 Use the Right 6 Button to select between On Off You can always go back to step 4 by pressing the L
5. will disappear indicating the Learn code is sent Once the remote is programmed the receiver control will quit from programming mode and the programmed remote is ready to be used now PROGRAMMING FOR ZONE OPERATION In the above table both the Family Room Ceiling Light and Family Room Floor Light are in zone 1 You need to assign the zone 1 signal to both receiver controls in these 2 locations That means for Light 1 in the example you need to program the following signals Button 1 to Light 1 based on Programming for Individual Operation Zone 1 Command to Light 1 base on Programming Zone Operation For Light 2 in the example you need to program the following signals Button 2 to Light 2 based on Programming for Individual Operation Zone 1 Command to Light 2 base on Programming Zone Operation KA f N k assign a zone to a receiver control follow the instructions below 1 Put the receiver control that you plan to program into programming mode Refer to the User s Instructions of that receiver control 2 During the standby mode the LCD display will show the current time Press the PROG button 3 times to enter the Zone Programming mode The Signal icon 1 and ZONE icon and red LED stay on for 15 seconds 6 3 Once the receiver control is in programming mode press the zone number button i e 1 for zone 1 Red LED will flash then off The signal icon will disappear indicating the
6. eft 4 Button 6 Press Enter 5 to confirm the setting Repeat the above steps to setup different timer operations 11 To Activate or Deactivate the Timer 1 During the standby mode press TIMER once show LCD 2 Press 1 9 to select the desired timer i e Enter 1 for Timer 1 3 Press TIMER again to activate or deactivate the timer If the Timer icon stays on the timer is activated If the Timer icon is off that timer is not activated BATTERY When the operating range is reduced the LCD backlight is dimmed or the red LED does not flash during operation it is time to replace the battery The remote is powered by 2 AAA alkaline batteries Follow the instructions below to replace the batteries to the transmitter 1 Slide out the battery door from the unit 2 Remove the old battery Insert 2 new AAA Alkaline batteries to the battery compartment Beware of the battery polarity 3 Insert the battery door to the remote The red LED on the front of the unit will be on for 1 second and the LCD will turn on After replacing the batteries please refer to the Section 3 Set the Clock to set the current time There is no need to program the devices zones timers or scene settings these settings are stored in the memory without being affected by the battery Caution Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions Declaration of Conformit
7. etting Press 5 to confirm 7 Now the Red LED stays on and the SCENE icon Signal icon and Settings icon stay on for 15 seconds to allow you to program this scene to the receiver control Put the receiver control that you plan to program into programming mode Refer to the User s Instructions of that receiver control Once the receiver control is in programming mode press the Scene number button on the remote i e 1 for Scene 1 Red LED will flash then off You have now programmed a Scene 1 signal with 60 brightness to the receiver control The LCD display will continue to show the setting for Scene 1 with the brightness setting flashing As most scene setting involves multiple lights with different brightness you may change the brightness again and program the same scene to another receiver control After finish programming all the scenes you may press the PROG button twice to return to clock mode Scene Operation To turn on a scene Press the Function button F once The SCENE icon and ON icon will stay on in the LCD display show LCD 2 Press 1 9 to select the desired scene i e Enter 1 for Scene 1 and all the lights in Scene 1 will be on at the preset brightness To turn off a scene Press the Function button F twice The SCENE icon and OFF icon will stay on in the LCD display show LCD 2 Press 1 9 to turn off the scene i e Enter 1 to turn off all the lights
8. i e common scenes are morning scene evening scene movie scene and etc 4 Timer Operation Allow you to set a timer to turn on or off specific light or zone or scene You may assign the buttons to specific lights and zones tele m Button Lights Zone 6 Bescon cating tint a master econ Gang tant Zonea 9 Fon verstion You may use the following table to fill in the lights or small appliances you would like to control and the related zone This will give you a clear direction during the programming process Number Button Lights Zone PROGRAMMING FOR INDIVIDUAL OPERATION Individual operation allows you to use one of the buttons from 1 to 9 to control one specific light or appliance To program a remote to the receiver control a Learn code must be transmitted follow the instructions below to transmit the Learn code to the receiver control lt JS 1 Put the receiver control that you plan to program into programming mode Refer to the User s Instructions of that receiver control During the standby mode the LCD display will show the current time Press the PROG button once to enter the Individual Programming mode The Signal icon 11 and red LED stays on for 15 seconds Once the receiver control is in programming mode press the button 1 9 on the remote that you plan to use to transmit the Learn code Red LED will flash and then off The signal icon
9. in Scene 1 You may assign a scene to specific receivers with preset brightness to create different atmosphere Some examples below Receiver Control Brightness Evening Family Room Floor Light PROGRAMMING FOR TIMER OPERATION The remote provides 9 timer settings so it will send signal to control the desired devices at the preset time You need to set the time day of the week and the action in advance You can set the following actions to control different devices 1 An individual light on off 2 Ascene on off 3 Azone on off To setup a timer Time and day or the week SCENE O a LI LI wn Press the PROG button 5 times to enter the Timer Programming mode The PROG icon and TIMER icon will stay on and the Timer number will flash in the LCD display show LCD Press 1 9 to select the Timer number you want to setup The day of the week e g SU will flash Select the day you want the timer to be activated by using the Up 2 Down 8 buttons To select press 5 The day of the week will turn solid meaning this is the day this timer will be on You can select multiple days such as Monday and Tuesday To de select press 5 again the day of the week will disappear After select the week then set the time to effective this timer operation Use the Right 6 and Left 4 button for the Hour and Minute setting Use the Up 2 or Down 8 button to set the time you want this
10. y This equipment complies with the requirements relating to electromagnetic compat ibility EN 300220 2 EN301489 3 EN61058 1 EN50371 This equipment conforms to the essential requirement of the Directive 1999 5 EC of the European Parlia ment and of the Council ce X 12 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com CUSTOMER SERVICE Rm 1303 Block B Veristrong Industrial Centre 36 Aupuiwan Street Fotan N T Hong Kong Email sales skylinkhome com http www skylinkhome com 2012 SKYLINK GROUP 1012945
Download Pdf Manuals
Related Search