SkyLink SK7 User's Manual
Contents
1. Red LED Pad Section 9 Setting a Timer Duration NOTE This section is for transmitters that are programmed to Flashing Alert Mode and Countdown Timer Mode The timer duration for both modes can be set for the following times 1 minute 5 minutes 15 minutes 30 minutes or 60 minutes like to go back to other settings such as 1 minute release the button and repeat A NOTE Once the number of flashes reaches 5 it will stay at this setting If you would from step 1 to start over A NOTE Usea sharp non conductive object like a pen or pencil to press the learn button 1 The connected light must be turned off and the two blue LEDs should be on 2 Press and hold the learn button for three seconds until the lower blue LED flashes once The number of flashes indicates the timer duration Timer Duration 1 min 5 min 15 min 30 min 60 min 3 Continue to hold the learn button until it reaches the desired setting The status will change every 6 seconds so holding the learn button for another 6 seconds the number of flashes will change from 1 to 2 2 to 3 etc Once a transmitter is programmed for the timer mode activating this programmed transmitter will turn the lights on for the specified timer duration To stop timer countdown press a programmed button for regular mode for timer operation the timer will start again and override the previous timer This A NOTE During a timer2. by the FCC and it complies with Part 15 of the FCC Rules Its operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s atuhority to operate the equipment Technical Specifications Input Voltage 120V AC 60Hz Standby Current 0 2mA Minimum Load 10W Maximum Load 300W at 120VAC Operating Frequency 318MHz Operational Temperature 4 F 140 F 20 C 60 C Humidity 5 95 Range Up to 500 feet in open area Package Contents Wall Switch Receiver 1 B Wireless Wall Switch Transmitter 1 o seewsandancios Double sided Foam Tape Section 1 Setting up the Wall Switch Receiver WARNING Turn off power to the circuit that you plan on installing the Wall Switch to at the circuit breaker Failure to turn off power at the circuit breaker can result in electrical shock causing severe or fatal injury fluorescent light with a maximum load of 300W at 120VAC Light bulbs must be dimmable A NOTE The Wall Switch is designed to operate incandescent light or dimmable compact in order to achieve dimming function NOTE Ifyou already have an existing 3 Way Switch disable one switch and replace the other switc
3. Z N SKY oat INSTALLATION INSTRUCTIONS WIRELESS 3 WAY ON OFF DIMMER KIT Model SK7 SkylinkHome Congratulations on your purchase of the SkylinkHome Wireless 3 Way On Off Dimmer Kit model SK7 Simply replace your existing wall switch with the Skylink Wall Switch receiver and mount the Wireless Wall Switch Transmitter anywhere you would like to control your lighting Warranty ONE YEAR WARRANTY This product is guaranteed to be free of defects in materials and workmanship for 1 year from the date of purchase If this product is defective call 1 800 304 1187 for repair or replacement parts Guarantee does not include normal wear and tear or batteries Z N SKY Cy If you have any questions problems or missing parts please call Skylink Customer Support 9 00am 5 00pm EST Monday Friday 1 800 304 1187 Or e mail us at support skylinkhome com www skylinkhome com CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y1J3 P N 101Y156 Rev 0 2014 SKYLINK GROUP Safety Information O Turn off power to the circuit breaker before installing O If you are uncertain or uncomfortable performing this installation please consult a qualified electrician This manual should also be kept for future reference O For indoor use only O DO NOT use this product to control loads over the specified maximum rating For dimming function the light bulbs must be dimmable The device is approved
4. ck plate with screws D 2 Tighten the two screws on the wall plate to the back plate to secure it 3 The Wireless Wall Switch transmitter is now ready to be controlled Drill 2 pilot holes amp insert anchors Make sure the air gap switch is in the off position and then turn the circuit back on Place the air gap switch to on position The two blue LEDs will be on If the blue LEDs remain off please check and ensure the light bulb is installed and in good position and that the wires are connected correctly After the Wall Switch is installed tap the metal touch plate to turn the lights on and off ON Position OFF Position Switch Touch Plate Section 3 Operation Wall Switch Receiver A NOTE Make sure the Air Gap Switch is in the on position before you start 1 To turn the light on and off tap the Wall Switch metal touch plate Tap the touch plate On Off 2 Todim or brighten the lights tap the metal touch plate to turn on the lights then press and hold to dim or brighten the lights Press and hold the touch plate Dimming Section 2 Setting up the Wireless Wall Switch Transmitter INSTALLING WITH DOUBLE SIDED TAPE NOTE The Wireless Wall Switch Transmitter comes with a lithium battery already installed Remove the battery isolator tag from the Wireless Wall Switch transmitter before installing 1 First clean the wall surface where you plan to install the Wire
5. countdown if the Wall Switch receiver receives another signal will extend the on period by another timer interval NOTE All previously programmed devices will be erased You must re program the devices you want to keep A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 Power off the Wall Switch receiver by sliding the air gap switch into the off position 2 Press and hold the learn button and slide the air gap switch back into the on position Air Gap Switch Blue LEDs Learn Button 3 The blue LEDs will first turn on and then turn off 4 Release the learn button 5 All devices have now been successfully erased Section 10 Replacing the Battery 1 Remove the wall plate from the Wireless Wall Switch transmitter by loosening the two screws 2 Remove the existing battery by sliding it out 3 Insert the new battery positive side up by sliding it in and pushing down on the battery to lock it in place 4 Whenthe battery is installed the red LED on the transmitter will be on for one second Slide in Battery Positive side up Red LED Section 6 Enable Disable On Off or Dimming NOTE On Off Mode turns the light on off without dimming and Dimming Mode turns the light on off or dims brightens WARNING Non dimmable load has to always be working under the On Off Mode Using non dimmable load under Dimming Mode may
6. ction 8 Countdown Timer Mode NOTE If the Countdown Timer Mode is activated the light connected to the Wall Switch receiver will be on for the predetermined time interval and then turn off otherwise the Wall Switch receiver will quit from programming mode and you will need to A NOTE You must compete the programming sequence within the 15 second interval start again from step 1 A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 To program a transmitter to operate in Countdown Timer Mode hold the learn button on your Wall Switch receiver for about 20 seconds until the upper blue LED is on steadily then release the learn button 2 Press the learn button on your transmitter 3 Once the transmitter is programmed both blue LEDs will flash quickly and stop flashing 4 The transmitter has been successfully programmed Learn Button NOTE Once you have successfully completed the programming go to section 9 to setup the timer duration for the transmitter NOTE Once you have successfully completed the programming go to section 9 to setup the timer duration for the transmitter Optional Snap On Decorative Cover Snap a cover into your Skylink Wall Switch Place the Snap On Cover on the opening of the Wall Switch receiver for a more stylish look Press or tap the cover TM 001 to turn lights on off or dim brighten Or carry the Snap On Remot
7. damage the non dimmable CFL A NOTE The factory default operating mode is on off 1 Turn the light on with the programmed transmitter or touch pad 2 Press and hold the button on the transmitter that is programmed to the Wall Switch receiver for 10 seconds or touch the pad with your finger for 10 seconds The LED will flash quickly 3 The light in the room will flash If it flashes once it is in On Off Mode If it flashes twice it is in Dimming Mode 4 Repeating step 2 will toggle the settings between On Off Mode and Dimming Mode Troubleshooting Problem Solution Ensure the corresponding wires are connected correctly Refer to Section 1 Ensure the wires are side by side and held together when pushing them inside the wire nuts Check that the circuit breaker is turned on Wall Switch Receiver s LEDs and the connected load will not turn on If there are white wires neutral in the wall box connect the white wire with a wire nut Only connect the Load and Live wires from the wall box to the Wall Switch Receiver My switch has more than 3 wires in the wall box This is normal Ensure the connected load does not exceed the maximum The Wall Switch Receiver is getting warm to touch rating The range of my Wall Keep the antenna wire as straight as Switch Receiver is possible and put it directly into the dry decreasing wall or via the hole in the wall box Ens
8. e TM 318 with you for local control and when you are done snap it back onto the Wall Switch Snap On Cover w Snap On Remote Model TM 001 Model TM 318 SkylinkHome For more information visit www skylinkhome com Accessories Add up to eight Skylink Wireless Transmitters wj l HF m EE SkylinkHome Wireless Wall Switch Model TB 318 Motion Sensor Model ID 318 E SkylinkHome t Snap On Remote Keychain Remote LCD Deluxe Remote Model TM 318 Model LK 318 Model TD 318 e a 000 E 2 000 oO Te Bn nai O O a N f Wireless Remote Control TC Series TC Series Remotes are available in 1 to 14 buttons For more information visit www skylinkhome com
9. h with the Wall Switch Receiver 1 Loosen the screws on the wallplate cover of the Wall Switch receiver and remove it before installing 2 Install the Wall Switch with the 3 wires Live Load and Ground Use the provided wire nuts C to connect these wires respectively to the existing wires from the wall Neutral wire is not required and cannot be connected to the Wall Switch Receiver 3 After all the wires are connected ensure that all of the wire connectors are attached securely and there should be no exposed copper wiring Secure the Wall Switch with screws Ground Usually copper or green Grey Antenna A NOTE Do not cut the antenna Section 2 Setting up continued INSTALLING WITH SCREWS NOTE The Wall Mount transmitter comes with a lithium battery already installed Remove the battery isolator tag from the Wall Mount Transmitter before installing Installing to an Existing Wall Switch 1 Loosen the screws on the wallplate cover of the Wireless Wall Switch transmitter and tighten the two included screws D on the back plate to the existing wall box 2 Tighten the two screws on the wallplate to the back plate to secure it 3 The Wireless Wall Switch transmitter is now ready to be controlled Existing Wall Box No Anchor Installing on New Wall Surface 1 Drill two small pilot holes based on the two mounting screw positions and insert the anchors D before tightening the ba
10. less Wall Switch transmitter 2 Place the two foam tapes E on the back of the Wireless Wall Switch transmitter plate Peel off the foam tape cover and stick it to the wall surface Place double sided foam tape Wireless Wall Switch Transmitter 1 To turn the light on and off push the Wireless Wall Switch pad from one position to the other Push Push 2 To dim or brighten the lights push the Wireless Wall Switch pad to turn on the lights then press and hold the same upper pad to dim or brighten the lights Press and hold gt Section 4 Programming Section 5 Erasing NOTE Before programming remove the wall plate on the Wireless Wall Switch transmitter by loosening the screws A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 Touch the metal touch plate on the Wall Switch receiver to turn the lights on The two blue LEDs should go off 2 Press and hold the learn button for about three seconds until the upper blue LED flashes quickly and then release the learn button Touch Plate Learn Button 3 Press the learn button on your Wireless Wall Switch transmitter The red LED will be on for 15 seconds 4 Press the pad switch on the Wall Switch Transmitter the red LED will flash and then go off The upper blue LED on the Wall Switch Receiver will also turn off 5 Both wall switches are now programmed Learn Button
11. ure the timer duration is set to the desired setting Check that there were no other Timer Mode signals being received as that will extend the ON period by another interval It takes a long time for the light to turn off when set to Timer Mode Can I connect the Wall Switch Receiver with 600W lights No Purchase the Skylink Wall Switch Receiver WE 001 WE 318 instead of this Wall Switch Receiver Can I dim the CFL with E the CFL is di ble the Wall Switch Receiver ASUTE We SESS SIAR e Section 7 Flashing Alert Mode NOTE If the Flashing Alert Mode is activated the light connected to the Wall Switch receiver will flash for a predetermined time interval and then turn off otherwise the Wall Switch receiver will quit from programming mode and you will need to A NOTE You must compete the programming sequence within the 15 second interval start again from step 1 A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 To program a transmitter to operate in Flashing Alert Mode hold the learn button on your Wall Switch receiver for about 10 seconds until the upper blue LED flashes slowly then release the learn button 2 Press the learn button on your transmitter 3 Once the transmitter is programmed both blue LEDs will flash quickly and stop flashing 4 The transmitter has been successfully programmed Learn Button Se
Download Pdf Manuals
Related Search