SkyLink OTODOR PS-201 User's Manual
Contents
1. buzzer beeping represents the timer setting Number of continuous beep Timer Setting 40 Seconds 50 Seconds 3 OPERATION CONT 3 To change the setting press the door setting button once will advance the timer by 10 seconds i e if the original timer setting is at 10 seconds pressing the door setting button once will result in 20 seconds and you will then hear 2 beeps The timer setting will be back to 10 seconds if you press the door setting button when the timer setting is at 50 seconds 4 Once you have selected the desired setting press and hold the door setting button for 3 seconds you will hear a long beep and the orange LED will be off You have now changed the timer setting 4 OTHER SWING DOOR OPENER ACCESSORI The swing door opener can work with different accessories include keychain wallmount transmitter 4 Button keychain transmitter motion sensor electric strike electromagnetic lock kit amp keypad transmitter etc Please visit www skylinkhome com or contact us at support skylinkhome com for more information of how to fully utilize your swing door opener 5 FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approv2. Motion Sensor Model PS 201 The Motion Sensor is designed to activate the Skylink s swing door opener automatically when it senses motion nearby the door The door will stay open for a period of time then closes if no further movement is detected In this package you should find a Motion Sensor battery included ball head joint and screws 9V Alkaline battery 2pcs 3x 18 screws Included Ball head joint Motion Sensor Please follow the instructions below to setup your motion sensor 2 INSTALLATION Insert a 9V alkaline battery included to the motion sensor and its LED will be on for 2 seconds 9V Alkaline Battery Before installing the sensor onto the wall or door frame you should learn the sensor to the door opener so they can communicate To learn the motion sensor to the door opener follow the procedures below 1 The door opener should be in standby mode i e adapter plugged in but the swing door opener should not be operating only the red LED should be on steadily 2 Press and hold the Learn button the red LED will start to flash and buzzer will beep indicating the door opener is now in learn mode 3 Press the test button on the motion sensor while you are holding onto the learn button on the door opener you should hear a long beep and the LED will be off You may now release both the learn button on the door opener and the test button on the sensor You have now suc
3. cessfully programmed the motion sensor to the door opener Learn button Note During the installation of the motion sensor it is recommended to disable the power supply to the door opener so the door will not open or close during the installation gt l The motion sensor should be installed above the door as illustrated You can mount the ball joint on the wall by screws Once the ball head joint is mounted to the wall slide the back of the sensor into the ball head joint see diagram The mounting angle can be adjusted Please refer to Walk Test to determine the best mounting angle 2 INSTALLATION CONT Walk Test After mounting the motion sensor it is important to test the coverage of the motion sensor In order to control how far the sensor can see this can be done by adjusting the angle You should adjust the angle so it only monitors several feet away from the door to prevent false trigger by motion from a far distance You should walk in the area that you would like the sensor to monitor If movement is detected the red light inside the unit will appear If the red light does not appear adjust the mounting angle accordingly Perform the walk test again after 3 seconds Repeat this procedure until your motion is detected There should be no movement in the detected area during the 3 seconds Perform walk test in the undesired N l area to ensure movement cannot N be detected NN Tips T
4. ed by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment dose cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 6 CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility EN 301489 3 2002 EN300220 3 2000 EN60065 1998 This equipment conforms to the essential requirement of the Directive 1999 5 EC of the European Parliamen
5. he sensor should not face towards direct sunlight placing near heat or cold producing devices i e A C or furnance vents fans ovens heaters etc that may cause false triggers Move the sensor downward to reduce the range 3 OPERATION When the motion sensor is triggered the door opener will open the door In order to close the door automatically the door opener must be set in the Timer operating mode To enable the timer mode 1 Unplug the door opener when it is in standby mode 2 Change the setting of the mode selection switch to Timer mode top position 3 Plug the adapter back and the red LED will be on steadily 4 Open the door by activating the remote or walking in front of the motion sensor After the door has been opened you should still hear the buzzer beeping indicating that the timer is counting down and the door will be closed soon The factory default timer is set to 10 seconds 5 After 10 seconds the door will be closed automatically Top position Timer mode You may change the timer setting from 10 seconds to 50 seconds in 10 second intervals To change the timer setting 1 Press and hold the door setting button for 3 seconds when the door opener is in standby mode You will hear the buzzer beeping rapidly and the orange LED flashing You may now release the door setting button 2 After the door setting button is released you should hear the buzzer beeping This
6. t and of the Council 7 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 8 CUSTOMER SERVICE If you would like to order Skylink s products or have difficulty getting them to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 C Fe CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com PIN 1012433 US Patent 6243000B1 2006 SKYLINK GROUP
Download Pdf Manuals
Related Search