SkyLink ID-318 User's Manual
Contents
1. Motion Sensor Model ID 318 1 INTRODUCTION Thank you for your purchase of a SkylinkHome Motion Sensor Model ID 318 The Motion Sensor allows you to activate a receiver module to turn lights on automatically when movement is detected A built in count down timer can turn lights off after a predefined time period This is ideal for energy saving purpose where an area is not always occupied but lighting is needed when someone is present A built in light sensor can also be used so the lights will not be on when the monitored area is bright enough even if movement is detected there All wireless signal communications within the SkylinkHome System are based on rolling code technology to ensure highest security is used The following items are included in this package Motion Sensor ID 318 Ball Joint and Mounting Accessories User s Instructions ily Ball Joint and Mounting Accessories 2 PROGRAMMING MOTION SENSOR TO RECEIVER MODULE In order to activate a receiver module for automatic control with a Motion Sensor it must be programmed to the receiver module Motion Sensor ID 318 To program a motion sensor to a receiver module follow the instructions below 1 Undo the door screw on the back of the motion sensor and remove the battery compartment door 2 Insert a 9V alkaline battery to power up the motion sensor 3 Put the receiver module that you plan to program into programming mode Refer to the User s In2. USTOMIZING THE MOTION SENSOR CONT If the jumper connector is in place the light sensor threshold is set to dark a motion activation signal will not turn on the lighting receiver unless the environment is really dark Pal If the jumper connector is removed the light sensor threshold is set to dim a motion activation signal will 17 N turn on the lighting receiver even the environment is not so dark You should set the desired light sensing threshold by trial and error fd 4 N L N After setting all the jumper connectors you may place the battery com partment door back on and tighten the screw You may now mount the motion sensor at the desired location where movement will be monitored 4 INSTALLATION You can use the mounting accessories to mount the Motion Sensor on a wall First mount the ball joint on the wall then slide the Motion Sensor on the ball joint You should mount it at a height of about 7ft from the ground to achieve better coverage 5 TESTING AND OPERATION Walk Test Walk test should be performed after the motion sensor is mounted Walk in the covered area if motion is detected a red light inside the sensor will flash If the red light does not flash motion has not been detected and you may need to re position the sensor Ensure you walk test the whole area that you would like the motion sensor to cover Note DETECTING AREA Unit meter Perform the walk test afte
3. ly erased all the devices from the lighting receiver To erase Motion Sensor from other receivers please refer to the instructions of the receivers 7 BATTERY When the LED does not flash ON then OFF etc after the Motion Sensor is triggered or when the motion sensor does not control receiver after movement is detected it is time to replace the battery Refer to Section 2 to open the battery door Note Dispose of batteries properly 8 FCC The Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules Its operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s authority to operate the equipment 9 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 10 CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ secti
4. on at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 11 ACCESSORIES The SkylinkHome System consists of many other devices such as SkylinkPad Remotes Motion Sensor ON OFF Wall Switch Wall Dimmer Plug In Dimmer with or without Repeater Plug In ON OFF Control Outdoor Indoor Screw In Dimmer ON OFF Dimming Control ON OFF Control Smart Button Garage Door Control etc Please visit Skylink website at www skylinkhome com for more information Fe CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 1012702 Patent Pending V2 0 2010 SKYLINK GROUP
5. r can be programmed to MR 318 or MD 318 under ON OFF or regular Operating mode 3 CUSTOMIZING THE MOTION SENSOR To customize your motion sensor open up the battery compartment door and set the jumper connectors according to your needs 5min 30min 60min SEN 2 CDS OFF SEN 1 SET CDS DARK x SEN 1 SEN 2 SEN 1 for high sensitivity SEN2 for low sensitivity The sensor in high sensitivity can monitor further movement up to about 11 meters and less movement is required for activation The sensor in low sensitivity can monitor movement within a shorter distance and more move ment is required for activation Set the jumper connector at either one of this positions SET Button For programming the Motion Sensor 5 min 30 min 60 min For setting the countdown timer duration For example you may set the connector at the 5 min position so the light will be on when a motion is detected and be off 5 minutes later if no more motion is detected Each of these receiver modules Model PA 318 PR 318 PL 318 LS 318 WE 001 WR 001 has its own countdown timer duration setting However when a motion sensor is programmed to any one of these receiver modules the motion sensor timer duration setting overrides the timer duration setting of the receiver module Therefore when movement is detected by the motion sensor the duration will be based on the motion sensor time
6. r setting You may also move the timer jumper connector away no jumper con nector at 5 30 60 minute In this case the light will be on when motion is detected and it will not be turned off by the built in countdown timer You must use other device such as a remote control to turn it off There are some situations where this is desirable For example a motion sensor installed in a conference room will turn on the lighting when someone walks into the room and the lighting should remain on until someone leaves the room and turns off the lighting manually Without this setting no timer during the meeting the lighting may be turned off if no movement is in the monitored area CDS Light Sensor OFF If the jumper connector is in place the CDS light sensing function will be disabled meaning even it is very bright if movement is detected by the motion sensor it will still send a signal to activate the receiver If the jumper connector is removed light sensor function will be enabled meaning the light will only be on if motion is detected and the brightness of the monitored area is low enough Jumper s connector a Timer O Light Sensor Light Sensor Disabled Enabled CDS DARK Light Sensing Threshold For setting the light sensing threshold Threshold Threshold Dark Bright Jumper connector 3 C
7. r you 1 have inserted the battery for more than 1 minute The sensor will not be triggered by a new motion unless no motion has been detected for 3 seconds Therefore wait for at least 3 seconds during walk testing to make a next movement Disable CDS Light Sensor during g walk test re enable it after walk test Note When installing the motion sensor avoid placing it near heat or cold producing devices i e A C or furnace vents fans ovens space heaters etc and avoid pointing it to the moving objects like a window curtain Air movement especially caused by changes in temperature may trigger the Motion Sensor Please carefully test your Motion Sensor so that it will only be triggered by wanted movement 6 ERASING MOTION SENSOR FROM RECEIVERS Erasing Motion Sensor from the Dimmable Receiver Module model MD 318 or On Off Receiver Module model MR 318 You may erase a transmitter from the receiver module but you cannot erase a specific device directly you must erase all the wireless devices then program the ones you want to keep Follow the instructions below to erase programmed transmitters 1 Power off the receiver module 2 Press the SET button on the Motion Sensor 3 Press and hold the SET button for at least 2 seconds Do not release this button until step 5 4 Power up the receiver module you will hear a beep 5 You may release the SET button 6 When the button is release you have successful
8. structions of that receiver module If you are programming the motion sensor to any one of these receiver modules Model PA 318 PR 318 PL 318 LS 318 WE 001 WR 001 you can only program the motion sensor under Countdown Timer or Flashing Alert operating mode of the receiver module If you program the motion sensor under Flashing Alert operating mode when movement is detected the light will flash for a predefined time period Please choose carefully on which operating mode you select during programming 4 Once the receiver module is in programming mode you may transmit the programming SET signal from the motion sensor by pressing Button the SET button once Make sure that the sensor faces a still object for example a wall a table top etc and not to be triggered at this moment 5 Once the motion sensor is programmed the receiver module will quit from programming mode Programming is now completed After you power the receiver if the light connected to receiver is on reprogram the motion sensor to the receiver twice consecutively After this procedure your load will be off after power on Now if motion is detected the red LED on the front of the motion sensor will flash and the load connected to the receiver module should also be on You may program the motion sensor to different receiver modules so when the motion sensor is activated all the receiver modules will be activated Motion Senso
Download Pdf Manuals
Related Search