SkyLink MK-1 User's Manual
Contents
1. GB 318 Skylink offers different lighting control Ma automation transmitters Visor Transmitters ane Keychain Transmitters and Keypad Transmitters ile FF to work with your receiver 29 a iets Program additional remote controls Smart Button GB 318 can learn up to sixteen single button transmitters or keypads or five 3 button transmitter To learn additional remote controls follow the instructions below 1 Press the learn button on the side of the GB 318 2 Once the learn button is pressed the LED will flash quickly Release the learn button 3 Within 30 seconds press the button on the remote control you would like to program 4 Once the remote control is programmed the LED will flash slowly in the same way as it flashes in standby mode 5 You may now operate the garage door opener with this remote control Learn Button For more information please visit our website at www skylinkhome com or contact us 9 BATTERY 3 Volt lithium battery CR 2032 included It is time to change the battery when the red LED on the transmitter does not turn on when either button is pressed DO NOT let children use the garage door transmitter without adult supervision Otherwise Children and others may be injured by the garage door 11 FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This2. device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 12 WARRANTY If within one year from date of purchase this product should become defective except battery du
3. Universal Garage Door Remote Control Model MK 1 1 INTRODUCTION Congratulations on your purchase of MK 1 the package includes Skylink garage door receiver Smart Button GB 318 and Skylink garage door transmitter remote control MK 318 In this package you will find the following Garage Door ae Receiver Smart Button GB 318 Garage Door Transmitter x Crimper MK 318 Battery inside Double Sided Tape Connect the receiver Smart Button GB 318 to your current garage door opener system you can use the transmitter remote MK 318 to open or close the garage door 2 RECEIVER INSTALLATION Unplug the power cord of your garage door opener before installation to ensure power is not connected DO NOT let children use the gargae door Transmitter without adult supervision Children can injure themselves or others by the garage door DO NOT use remote to control the door without safety beams WARNING _ s Open up the Easy Clip and place it underneath the existing 2 wires of the wall button wall console 2 Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the Easy Clip Wall Button Ribbon Wires NOTE Ensure the ribbon wires are not twisted but laid flat inside the clip If your wall button ribbon wires Press lock are not the same kind as shown in the diagram please refer below 4 or v
4. able password 1 Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly 2 Input old password 3 Press 1 and 3 once simultaneously to confirm If the password is correct the password protection will be disabled Enable password 1 Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly 2 Input old password 3 Press 1 and 3 once simultaneously to confirm If the password is correct the password protection will be enabled You can toggle the two states password protection enabled or disabled Note The time out period is 10 seconds during any of the above setting operations After 10 seconds the LED will flash 3 times and the remote will exit from setting If you forget your password and want to reset MK 318 follow the steps below 1 Press 1 and 2 simultaneously and hold for more than 10 seconds until the LED flashes 2 After you release 1 and 2 the LED will be turned off and MK 318 will be reset The password will be reset to factory default After the reset password protection is removed but the remote can not control any receiver until you reprogram it to receivers you want to control 8 OPTIONAL ACCESSORIES AND OPERATIONS You can add up to sixteen single button a transmitters or keypads or five 3 button additional transmitters or keypad to control the
5. e to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 13 CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 101Z994 002 Patent Pending are registered trademarks of their respective corporations 2010 SKYLINK GROUP
6. er has been programmed to the receiver Refer to section 2 for how to program a transmitter to the receiver 7 TRANSMITTER PASSWORD PROTECTION Password protection The MK 318 can be password protected If you enable the password pro tection you can only operate MK 318 after you input the correct password Password can be 2 8 digits long which is a combination of 1 2 and 3 For example password can be 1 2 1 2 To input this password you have to press button 1 then 2 then 1 then 2 Note 1 Button 1 2 Button 2 3 Button 3 Button 1 Button 2 Button 3 Note The time out period is 1 second during above password input The factory default password is 2 2 2 and this password function is disabled out of factory Change password 1 Press 1 and 3 simultaneously and hold for more than 6 seconds until the LED changes from flashing quickly to flashing slowly 2 Input old password 3 Press 1 and 3 once simultaneously to confirm If the password is wrong the LED will flash 3 times and you have to start it over from step1 4 Input new password 5 Press 1 and 3 once simultaneously to confirm 6 Input new password again 7 Press 1 and 3 once simultaneously to RE confirm If the password is different from the one of step 4 the LED will flash 3 times and you have to start over from step 1 Otherwise the password has been changed to the new one and the password protection is enabled Dis
7. ill still work if you plug in an adapter purchased separately Please contact Skylink to purchase the adapter Rating of the transformer 12V DC 100mA O lt Diameter of DC plug 3 5mm 7 Secure the SmartButton GB 318 properly with the mounting accessories Note Do not cut the antenna Straighten up the antenna to improve signal reception Note After installation of the Easy Clip if you want to re install the Smart Button GB 318 to another place please open the Easy Clip by gently unlocking the two buckles with a screw driver and remove it from the wires Do not re use the Easy Clip refer to Step 4 to re install it 3 PROGRAM TRANSMITTER MK 318 TO RECEIVER GB 318 You need to do the programming in order to add the transmitter to a receiver Smart Button GB 318 can learn up to sixteen single button transmitters or keypads or five 3 button transmitter To add remote controls follow the instructions below 1 Press the learn button on the side of the Smart Button GB 318 2 Once the learn button is pressed the LED will flash quickly Release the learn button 3 Within 30 seconds press any one of the 3 buttons on the transmitter that you want to program to the receiver 4 Once the remote control is programmed the LED will flash slowly in the same way as it flashes in standby mode 5 You may now operate the garage door opener with this new remote control 6 To p
8. isit our website www skylinkhome com or i Ribbon Wi contact us for more information atiii 3 Press and lock the clip by snapping it together The included Crimper helps you lock the Easy Clip Close the cover and press down to lock the cover using this Crimper until you hear a click 4 If the Easy Clip cannot clip the wires from your wall button cut off the Easy Clip then connect two wires from the Smart Button GB 318 to the wall button a Disconnect the existing wall button from the wall b Connect the 2 wires from the Smart Button GB 318 to your existing wall button Polarity does not matter so simply pick one wire from the Smart Button GB 318 and connect it to one of the screw terminals on your wall button Connect the 2nd wire to the other screw terminal Push Button c Reconnect the wall button back Terminals 5 If the wall button wires are hidden inside the wall please connect the Easy Clip to the exposed wires attached to the terminals of the garage door opener 6 Power up the garage door opener the red LED on the Smart Button GB 318 should keep flashing slowly for 2 minutes 2 RECEIVER INSTALLATION CONT If the Smart Button GB 318 s red LED does not flash after the Smart Button GB 318 has been connected to the wall button s wires for 2 minutes your garage door opener is probably too old However the Smart Button GB 318 w
9. rogram this transmitter to control another receiver repeat process 1 to 4 to program another button on the remote control 4 OPERATION If the red LED flashes slowly the Smart Button GB 318 is in standby mode When a valid remote control signal is Learn Smart Button received it will open close the garage door LED Press the programmed button on the remote control PEN or Smart Button GB 318 it will open close the CLOSE garage door Button 5 ERASE TRANSMITTERS To erase unwanted remote control s from the memory of Smart Button GB 318 first erase all remote controls then learn the one s you would like to keep follow the steps below 1 Press and hold the learn button for approximately 10 seconds 2 The LED will flash rapidly after 10 seconds to indicate all the pro grammed remote controls have been erased You may now release the learn button 3 You have erased all the remote controls programmed to the Smart Button GB 318 6 TROUBLE SHOOTING Q What can do if the door opener does not react after press the button on the transmitter A Ensure when the button on the transmitter is pressed the red LED on the transmitter comes on Otherwise check if the battery is inserted properly Make sure the correct button on the transmitter is pressed Ensure the wires that were previously connected to the wall mounted door control are not loose Ensure the transmitt
Download Pdf Manuals
Related Search