SkyLink AD-433S User's Manual
Contents
1. We have also included wall anchors and a template to help position the screws correctly How to use the template 1 Cut the template in correct position 2 Screw part way into the surface where the holes are marked 4 Unscrew the screws and remove the template 5 Screw the component in place where you started the screws INSTALLING THE DIAL ALERT AD 433S Position the dialer beside a telephone or near any phone line and within access of an electrical outlet However it is recommended that you hide the dialer for security purposes The dialer runs on regular electrical current It also contains a 9 volt backup battery in case power is interrupted for any reason A phone line must be connected to the dialer in order for the dialer to work Connect the phone lines and AC adapter as shown Note The optional line input is intended for answering machine tele phone etc The device connected to the dialer will be disconnected when the dialer is activated Therefore it will not affect the operation of the dialer There are 3 ways to attach the Dial Alert on the wall 1 Using double sided tape for temporary use 2 Hanging it from the two keyholes on two stationary screws 3 Screwing the back onto the wall with four screws To mount the Dial Alert 1 Open the case a Press the two tabs on top of the dialer b Pull open the front INSTALLATION 2 Thread the telephone line through the top a hole in the back of the uni2. need to open the case by pressing the two tabs on top of the dialer and pull open the front The Tone Pulse switch is located at the upper left corner of the circuit board just above the adapter jack The switch is set to Tone at the factory This setting can be changed by sliding the switch to the appropriate position Speaker On Off Switch The speaker must be on during programming and recording the voice message in order to use the playback feature For security pur poses the speaker may be turned off after programming to allow for silent dialing when the dialer is activated The On Off switch for the speaker is located on the lower right corner of the circuit board The default setting for the speaker is On LIGHTS AND SOUNDS Below is an explanation of the lights and sounds of the Dial Alert LIGHTS ACPWR light on ACPWR light off LOBATT light off LOBATT light on DISARM light off DISARM light on Keypad backlight flashing Keypad backlight SOUNDS Short beep Two short beep s Long beep Steady repeated beep dialer is being powered by AC adapter dialer is not receiving any AC power backup battery is connected and working backup battery is weak battery needs to be replaced the dialer will dial the pre programmed phone numbers when activated the dialer will not dial any phone numbers when activated 1 The dialer has no message in memory 2 Dial tone is not detected when the diale
3. release the R P key display will show PLAY and the dialer will beep The message is then played back If you want the dialer work without noise means no beep or let no body knows the dialer is dialing just turn off the Speaker Switch inside the case STORING TELEPHONE NUMBERS This feature enables the user to program as many as 9 different telephone numbers The dialer can send out 2 different messages One message is the pre recorded voice message that you programmed earlier the other message sends numeric information to a pager There are three different ways that you can send the voice message and the numeric information A Sends the emergency voice message only B Sends both the emergency voice message and the numeric infomation pager reception only C Sends the numeric information only for pager reception only Cautions okylink recommends that the telephone or pager numbers of your relatives neighbors office work friends or doctor be programmed into your Dial Alert Do not program the phone number to police or fire dept directly into your Dial Alert unless you have checked with your local authorities Please also inform all the recipients that their phone numbers have been programmed into your dialer so they know exactly what happen when they receive your emergency message A Storing telephone numbers in memory Sends the emergency voice message only 1 Press the key the display will show a lette
4. the Dial Alert AD 433S 1 Press the L key display will show L 2 Press the 5 key display will show L5 Id 3 Activate the desired transmitter sensor within 5 seconds after pressing the 5 key Refer to the user s instruction of the sensor to determine how to activate it Once the transmitter sensor are learned to the dialer the display will return to clock mode 4 To ensure that the sensor has been learned activate the learned sensor when the dialer is in the clock mode If the dialer starts dialing the preset phone numbers the sensor has been learned To terminate the dialing press and hold the Panic Button O on the keypad for 2 seconds To program control panel SC 001 SC 002 to the Dial Alert AD 433S 1 Press the L key display will show L 2 Press the 5 key display will show L5 Id 3 Enter the current MPIN Master Personal Identification Number on the Security Control Panel 8C001 SC002 4 Press B B on the Security Control Panel 8C001 5 002 Once the security control panel is learned to the dialer the display will return to clock mode DELETE PROGRAMMED TRANSMITTERS SENSORS SECURIT Y SYSTEMS Once a transmitter sensor security system is learned it is stored in memory In order to delete any one of the sensors first the entire memory must be erased then re learn the transmitters sensors security systems you wish to use You cannot erase only on
5. trigger the dialer by the existing alarm system is to use the Alarm Sensor SS 433 in conjunction with the Dial Alert see Additional Accessories page 25 en BATTERY MAINTENANCE The AD 433S Dial Alert comes with 1 battery that at some point you may have to replace One 9 volt alkaline battery for the Dial Alert Recommendation Test your Dial Alert periodically to ensure that the battery is working Dial Alert Battery The Dial Alert comes equipped with a 9V backup battery in case the elec trical power is interrupted for any reason When the dialer backup battery is low the LOBATT light goes on To replace the dialer backup battery 1 Undo the two screws on the back of the Dial Alert 2 Open the Dial Alert case by pressing down on the two tabs on the top edge and pull the front forward 3 Disconnect the old battery 4 Connect the new battery 5 Close the Dial Alert case and re insert the two screws The battery life 9 volt alkaline battery is approximately two years if used only for backup Note If the AC adapter is disconnected while the battery is being replaced the pre recorded message will be erased and the clock will return to 12 00 Re record the emergency voice message and reset the clock Refer to page 10 The pre programmed phone numbers will not be erased even the power is disconnected pja ADDITIONAL ACCESSORIES Additional sensors and transmitters as well as add on access
6. 101 20 JUNE 2004 E www skylinkhome com DIAL ALERT MODEL AD 433S PREMISES PROTECTED BY ELECTRONIC SECURITY SYSTEM HEALTH GARE HELP CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Tel 800 304 1187 Fax 800 286 1320 PAT D410633 Email support skylinkhome com 6243000B1 Emergency Dialer DIAL ALERT AD 433S USER S INSTRUCTIONS SKYLINK TECHNOLOGIES INC Your Guide to the Emergency Dialer DIAL ALERT MODEL AD 433S The AD 433S Emergency Dialer contains all the above items um TABLE OF CONTENTS PACKAGE CONTENT S u u nunana Sus Ga aiba 4 OVERVIEW ient aetatis u n 5 gio m Nr PAN 6 AND SOUNDS tuo used le hc ve cave ie kia 9 STANDARD PROGRAMMING et tees 10 14 3Prodramihe Time Glow an ee ics 10 Recording a Message a u 10 Playback Pre recorded Message 11 Storing 51966 uu u a u u u a 11 A Storing telephone numbers in memory Sends the emergency voice message 11 12 B Storing telephone numbers in memory Sends both emergency voice message and numeric information 12 C Storing tele
7. ONALACCESSORIES eene nnne nnn nnns 24 26 Ee PACKAGE CONTENTS All materials required for installation are included with this package Dial Alert AD 433S Telephone Line antenna installed AC adapter 9 volt alkaline battery ll 1 Pack of screws adanhaors fcbial Alert One template Double sided tape User s instructions Warranty Card Quick Guide 4 OVERVIEW Automatically call for help when emergency The AD 433S Dial Alert dials as many as 9 pre programmed telephone numbers and sends a personalized pre recorded message Each telephone number can be dialed up to 9 times and the person receiving the emergency message can confirm receipt of that message by pressing the key on their telephone A pre recorded message maximum 40 seconds in length will be played notifying the person being called of the emergency The Dial Alert works in conjunction with Skylink s Security Systems SC 5 SC 10 SC 100 series SC 200 series and all the Skylink Sensors Trans mitters When the alarm sounds on the control panel on any of our security systems the Dial Alert will be activated The Dial Alert is activated when 1 The red panic button O on the keypad of the Dial Alert is pressed 2 The button is pressed on the panic transmitter PT 434 sold separately 3 The red panic button O on the keypad of our security system SC 100 is pressed 4 The r
8. Press the 9 key display will show L9 1 The last digit 1 indicates that the universal dial tone detection is turned off 3 Press the 2 key within 5 seconds after pressing the 9 key to turn on the universal dial tone 2 92 ADVANCED PROGRAMMING When the universal dial tone is turned off and no dial tone is detected within 1 minute after the dialer is activated the display will show no LInE and the backlit keypad will flash To return to standby mode Display shows the time press and hold the panic button O for 2 seconds DIAL SEQUENCE SETTING During an emergency the dialer can dial the preprogrammed phone numbers in two different sequences 1 dials each preprogrammed telephone number once and when the last number is dialed the dialer goes back to the first phone number Dials it once then dials the second telephone number once and continues this sequence until the last number is dialed and if the redial is set to 3 it will repeat this sequence one more time 2 will completely dial the first preprogrammed phone number before dialing the second programmed telephone number If the redial count is set to 3 the dialer will dial the first telephone number three times then dial the second number three times and continue with this sequence until all the telephone numbers are dialed To program the Dial Sequence Setting 1 Press the L key display will show L 2 Press the 0 key display will s
9. appear on the display asking for a redial count The redial count is the number of times the dialer will call that telephone number The dialer is factory set to call the number 3 times The number of attempts can be changed to dial 1 to 9 times If you want to keep the redial count at 3 attempts press the MEM key To change the redial count enter a number from 1 9 when display shows rEdIAL 3 7 Input the repeat times when the display shows rEPEAt 3 The repeat time is the number of times the message will be played for that certain phone number The current setting is 3 It can be changed from 1 to 9 using the keypad Again by pressing MEM will keep the existing setting DELETE A TELEPHONE NUMBER FROM MEMORY 1 Press MEM key 2 Select the memory location 1 9 of the phone number you want to delete 3 The phone number will be shown on the display if that is the number you want to delete press the R P key while the telephone number is on the display Once the phone number is deleted the display will return to clock mode cde STANDARD PROGRAMMING TO REVIEW OR MODIFY THE PRE PROGRAMMED PHONE NUM BERS THE REDIAL COUNT AND OR THE REPEAT TIMES OFA PHONE NUMBER 1 Press the MEM key display will show an M in the upper right corner Select the memory location of the phone number 1 9 The phone number will be shown on the display BOO nm If you want to change the telephone number enter the new phon
10. ay shows rEPEAr 3 7 The dialer is now in standby mode Display shows the time The sequence to store a telephone number is as follows MEM enter memory location 1 9 enter telephone MEM enter redial 1 9 enter repeat 1 9 B Storing telephone numbers in memory Sends both emergency voice message and numeric information 1 Press the MEM key the display will show a letter M on the upper left corner If nothing is entered within 5 seconds the display will return to the clock mode 2 Within the first 5 seconds select a memory location by pressing a keypad number 1 9 to store the telephone number 3 Enter the teleohone number using the keypad The display will flash as the telephone is being entered To insert a pause period between any digits of the pre programmed telephone number or after the telephone number and before the numeric message used for pagers see PROGRAMMING A PAUSE PERIOD page 15 4 Press MEM 5 rEdIAL 3 will appear on the display This is the redial count which is the number of times the dialer will call that telephone number The dialer is factory set to call the number 3 times The number of attempts can be changed to dial 1 to 9 times If you want to keep the redial count at 3 attempts press the MEM key To change the redial count enter a number from 1 9 when display shows rEdIAL 6 The display will now show rEPEAt 3 This is the repeat count whic
11. begins to dial To deactivate the dialer press and holding the red panic button o on the keypad for two seconds If you have successfully aborted the call the display will go back to clock mode If the dialer has not been deactivated within those 45 seconds the dialer will dial the emergency phone numbers To set the dialing delay 1 Press the L key the display will show L 2 Press the 8 key the display will show L 8 1 The last digit is the current delay dialing setting 3 Press either 1 2 3 4 or 5 to set the delay dialing time refer to the chart below 1 0 seconds 2 30 seconds 3 45 seconds 4 60 seconds 5 75 seconds UNIVERSAL DIAL TONE This feature allows our Dial Alert to be compatible with all phone systems worldwide When the Universal Dial Tone is off our Dial Alert needs a dial tone before it will dial the pre programmed telephone numbers However not all phone systems and dial tones are the same For instance the dial tone may be different for any phone system that accommodates the voice message systems or call answer feature When the Universal Dial Tone is on our Dial Alert will dial no matter what type of dial tone is present This Universal Dial Tone is factory set to off However you may wish to set it to on if your phone line accommodates the voice message systems or call answer feature Turn on the universal dial tone 1 Press the L key display will show L 2
12. ch phone number once then repeats sequenca 2 m Finishes dialing first phone number then begins the second number 1 Regular phone 2 1 0 2 1 27O N 1 T 1 7 DEFAULT DISPLAY iza 1 2 DISARM PANEL OR SENSOR AD 433S N C LATCHING DRY CONTACT NORMALLY CLOSED BS Remove the OPENS ALARM jumper first DIAL ALERT QUICK GUIDE FEATURE Remove the jumper first Place the Alarm Sensa beside the siren of your existing alarm system once the alarm is activated the siren will sound and the Alarm Sensor will be triggered and send a signal to the Dial Alert to activated it There is no wiring involved in this case o 9 x 2 e 0 A 1 c lt ul a a d O 2 L uc oc lt Ll T 4 ie TO LEARN ID CODE OF TRANSMITTERS SENSORS L5 TO SET PAUSE TIME FOR PAGERS NUMERIC CL 8 TO ERASE TRANSMITTERS SENSORS FROM THE MESSAGE TO SET CALLING TIME TO SCT PIIONE SYSTEM TO SET CLOCK HOUR MINUTE TO ARM DIGARM THE SYSTEM TO SET EXIT ENTRY DELAY DIALING TO SET UNIVERSAL DIAL TONE TO SET REDIAL SEQUENCE TO SET DIALING PAUSE TIME KEYPAD FOR 2 SECONDS SYSTEM NOTES 9 NUMERIC CHOICE see SETTINGS column L 2 d L d L d L 9 4 9 d L d L 1 d FUNCTIONS The other way to
13. e message press and hold the R P key for 2 seconds the display will show rEcord and a beep is generated which alerts you to begin recording The microphone is located beside the speaker Record all the infor mation you would like to be played in case of an emergency For example This is an emergency voice message my name is John Smith please send help live at My phone number is xxx xxx xxxx if you have two phone lines give the phone number of the line that the dialer is not using This dialer includes a special feature to let the called party terminate the emer gency message By pressing while the message is being played the Dialer will stop calling that number then advance to the next number if any We recom mend that a short ending be recorded after the emergency message informing the recipient of this feature i e this message will call you x times and repeat x times during each call to acknowledge and discontinue further calls press After you are finished recording the message maximum length of 40 seconds press R P key display will show PLAY and play back the message After playing the message the display will return to clock mode The keypad back light will stop flashing indicating that a message has been recorded The sequence to record a message is Press and hold R P for 2 seconds record message press STANDARD PROGRAMMING PLAYBACK PRE RECORDED MESSAGE Press and
14. e number while the old number is on the screen This telephone number will be deleted when a new number is added Then press the MEM key If you want to keep the telephone number shown on the screen press MEM 5 The display will now show the current setting of the redial count If you want to keep the current redial count enter the MEM key If you want to change the setting enter the desired number 1 9 then press the MEM key 6 After pressing the key the display will show the current setting of the repeat times 7 lf you want to keep the current repeat time enter the MEM key If you want to change the setting enter the desired number 1 9 then press the key 8 The screen will revert back to clock mode ACTIVATE THE DIAL ALERT WITH THE PANIC BUTTON ON THE KEYPAD After you programmed all the emergency telephone numbers and the voice message you can activate the dialer by pressing the panic button on the keypad Once the panic button is pressed the dialer will start dialing the pre programmed emergency phone numbers You can also activate the dialer using the Panic Transmitter PT 434 sold separately 14 ADVANCED PROGRAMMING PROGRAM THE CALLING TIME The calling time is the amount of time the phone will ring until the call is dis contected If the phone is not picked up within this period of time the dialer will either call again depends on the redial count or advanc
15. e sensor on garage door Activates Security Control Panel SC 001 when the garage door is opened 12V alkaline battery included Temperature Sensor TS 433 Monitors temperature of a specific area i e greenhouse horse farms laboratory etc Activates Security Control Panel SC 001 or Emergency Dialer AD 433S when the tempera ture of the monitored area is above or below a preset temperature Temperature range 0 F 19 C to 159 F 69 Operates using lithium batteries included Flood Sensor FS 433 Place sensor along basement wall near water heater washing machine etc Notifies Security Control Panel SC 001 or Emergency Dialer AD 433S when water is detected 12V alkaline battery included 26
16. e specific sensor the entire memory must be cleared q 7 ADVANCED PROGRAMMING To erase transmitters sensors security systems from the dialer 1 Press the L key the display will show L 2 Press the 6 key the display will show L6 Press the 2 key If your hear a double beep all transmitters sensors security systems have been deleted TO ARM DISARM THE DIALER The dialer can be armed to send messages when the transmitters sensors that are learned have been activated You can also disarm the dialer so that it will not be activated even if any of the learned transmitters sensors are activated You may choose to disarm the dialer when you are home and the door window contact on your front door is active The dialer is currently set to arm mode To arm disarm the dialer 1 Press the L key the display will show L 2 Press the 7 key the display will show L 7 1 The last digit 1 indicates the dialer is armed 3 To disarm the dialer press the 2 key within 5 seconds after pressing the 7 key When the dialer is disabled the display will read L7 2 When the dialer is disarmed the disarm LED light will be on DELAY DIALING ENTRY EXIT MODE The delay dialing function temporarity disengages the dialer for a specified period of time either 30 45 60 or 75 seconds This delay allows you to activate any sensor without activating the dialer The dialing delay serves tw
17. e to the next phone number The calling time is currently set at 60 seconds How to program the calling time 1 Press the L key the display will show L 2 Press the 1 key the diplay will show L 1 1 the last digit 1 is the setting of the call time in this example it is currently 30 seconds as per chart below To keep this setting press the L key 3 To change the calling time press either 1 2 3 4 or 5 when the diplay shows L 1 1 refer to the chart below 1 30 seconds 2 45 seconds 3 60 seconds 4 75 seconds 5 90 seconds If the display shows L 1 the phone will ring for 60 seconds before the call is disconnected PROGRAMMING A PAUSE PERIOD When storing a phone number you are able to insert a pause period between any digits of the phone number or after the phone number and before the numeric message for pagers To set the pause period for pagers numeric message 1 Press the L key the display will show L 2 Press the 2 key the display will show L 2 5 the last digit 5 is the setting of the pause period in this example it is currently set at 5 seconds to keep this setting press the L key 3 To change the pause period between 1 to 9 seconds press 1 9 on the keypad while the display shows L 2 5 If the number 9 is entered the pause period between the number dialed and the numeric message is 9 seconds Program pause pe
18. ed button on the keychain transmitter 4B 434 is pressed 5 The security system SC 100 SC 200 is activated by any programmed sensors i e door window sensor motion sensor etc The security systems keychain transmitters and sensors must first be programmed to communicate with the Dial Alert This user s instructions is divided into 4 sections in order to assist in the installation and programming of your Dial Alert 1 Installation 2 Lights and Sounds 3 Standard Programming Program the time clock Record a message Playback of pre recorded message Storing telephone numbers in memory for emergency voice message only both emergency voice message and numeric pager information numeric pager information only Delete a telephone number from memory Modify a telephone number the redial count and repeat times of a phone number 4 Advanced Programming Programming the calling time Programming the pause period for pager access and telephone numbers Select the phone system regular or PABX phone systems Program transmitters accessories to activate dialer Erase programmed transmitters accessories To arm disarm the dialer Dialing delay Universal Dial Tone INSTALLATION The Dial Alert is installed using the screws provided We have also included double sided tape to use for temporary installation while you are positioning the dialer Once the dialer is positioned correctly install it permanently with screws
19. h is the number of times the message will be repeated during that one call The dialer is factory set to repeat the message 3 times The number of repeats can be changed from 1 to 9 times If you want to keep the repeat count to remain at 3 times press the MEM key To change the repeat count enter a number from 1 9 when display shows rEPEAt 3 STANDARD PROGRAMMING C Storing telephone numbers in memory Sends the numeric information to pager only 1 Press the MEM key the display will show a letter M on the upper left corner If nothing is entered within 5 seconds the display will return to the clock mode 2 Within the first 5 seconds select a memory location by pressing a keypad number 1 9 to store the telephone number 3 Enter the telephone number using the keypad The display will flash as the telephone is being entered To insert a pause period between any digits of the pre programmed telephone number or after the telephone number and before the numeric message used for pagers a pause period must be added between the telephone number and the numerical message Refer to the Pager Company to identify the pause needed see PROGRAMMING A PAUSE PERIOD page 16 4 Enter the numeric information you want to send out the information that will be shown on the pager then press L This will suspend the recorded message 5 Press MEM 6 After the telephone number has been stored another message will
20. how LO 2 The last digit 2 is the dial setting sequence It is currently set to dial first number completely then repeat next sequence 3 To change the dial setting sequence enter either 1 or 2 when the display shows LO 2 refer to the chart below 1 2 dialer dials each phone number once then repeats sequence dialer finishes dialing the first phone number then begins the second number 20 ADVANCED PROGRAMMING CONNECT THE DIAL ALERT WITH YOUR EXISTING ALARM SYSTEM You may connect your existing alarm system with the Dial Alert so that the dialer will be triggered by your alarm system when it is activated There are 2 ways you can connect your dialer with your existing alarm system 1 Connect the dialer with the alarm system using hard wire normally closed 2 Connect the dialer with the alarm system using the Alarm Sensor SS 433 Follow the diagram below for hardwiring the dialer with the existing alarm system Every time the alarm system is activated it will automatically trigger the dialer to dial out all the preset telephone numbers and play the pre recorded message 75 seconds 6 PABX 5E 5 6 The clock is in 24 hour mod 5 ld eodE AcHvate the transmilter isensor within 5 sec 4 5 45 4 3 4 9 0 10 seconds 2 323 4 6 9 30 3 2 3 9 1 2 7 8 8 1 2 7 1 30 2 45 3 60 4 75 5 90 seconde 4 5 9 seconds 1 Dials ea
21. o purposes It allows you to leave the premises without activating the dialer and allows you to enter the premises and gives you time to turn off the dialer before it begins to dials Exiting a premises using the delay dialing If exiting a premises through a door that is monitored with a door sensor the delay dialing is set to 0 seconds and the dialer is on the dialer will dial the preprogrammed telephone numbers everytime you open that door When the dialer is set to a specified delay 45 seconds for example and that door is opened the dialer will be inactive for 45 seconds which allows you to leave the premises The screen on the dialer will display dELAY while the delay in on After the 45 seconds the dialer is re activated the screen returns to clock mode and the dialer is ready to receive an emergency signal from any pro grammed sensor 18 ADVANCED PROGRAMMING Entering a premises using the delay dialing If entering a premises through a door that is monitored with a door sensor the delay dialing is set to 0 seconds and the dialer is on the dialer will dial the preprogrammed telephone numbers immediately once that door is opened or any sensor is activated When the dialer is set to a specified delay 45 seconds for example and that door is opened the dialer will beep for 45 seconds and the screen will flash HELAY while the dialer is beeping This 45 seconds allows you to go to the dialer and deactivate it before it
22. ories are available to work with your Dial Alert Motion Sensor PS 433A Monitors area in a 110 degree ARC and up to 40 feet away from the sensor 9V alkaline battery included Door Window Sensor WT 433 Attaches to all doors windows entrances Add on as many magnetic switch MS 001 as needed 12V alkaline battery included Magnetic Switch Magnet MS 001 Used in conjunction with Door Window Sensor WT 433 Add on for additional doors windows Keychain Transmitter 4B 434 Activates Security Control Panel SC 001 instantly by pressing panic button Arm Disarm Security Control Panel SC 001 Reliable design crystal base transmission with microcontroller 12V alkaline battery included Audio Alarm AA 433 Additional indoor outdoor siren Water resistant 120 dB siren with flashing LED Operates by AC adapter with 9V alkaline back up battery included 24 ADDITIONAL ACCESSORIES Security Control Panel SC 001 Four alarm modes Day Night Away Chime Four zones each zone controls up to 6 decives Reliable design with microcontroller 110dB siren Silent Alarm SW 433 Plug into any AC outlet then plug light into Silent Alarm unit Light flashes when sensor s transmitter s is are activated Silently alerts occupants including the hearing impaired Vibration Sensor VS 433 Activates Security Control Panel or Emergency Dialer
23. pause period will be entered The pause period will be anywhere between 1 9 seconds see the beginning of this section to set the length of the pause period Example if you wanted a pause between the third and forth number the sequence would go as follows 568 2095 If the pause period was set at five seconds there would be a five second delay between the 8 and the 2 SET THE TYPE OF PHONE SYSTEM This dialer supports both regular telephone and PABX phone systems Selection can be made using the function key The dialer is currently set for regular phones To select the phone system 1 Press the L key display will show an L 2 Press the 3 key display will show L3 1 the last digit 1 means the dialer is set for regular phone 3 To change the setting of the dialer to PABX systems press 2 The display wil show L3 2 the system is now set to PABX system ADVANCED PROGRAMMING PROGRAM THE ID CODE OF A TRANSMITTER Before any transmitter sensor security system can activate the Dial Alert they must be learned programmed to communicate with each other Once they are learned the button on the transmitter a door with the door window sensor on it is opened someone walks through an area monitored by the motion sensor or the siren sounds on the security system the dialer will begin to dial the preset telephone numbers and play the pre recorded message To program Skylink s transmitters sensors to
24. phone numbers in memory Sends the numeric information to pager only 13 Delete A Telephone Number From Memory 13 To Review or Modify the Pre programmed Phone Numbers The Redial Count and or The Repeat Times of a Phone Number 14 Activate the Dial Alert with The Panic Button on the Keypad 14 ADVANCED PROGRAMMINGQ nennen ennt tnnt 15 20 Program the calling 15 Programming a Pause 15 Set the type of Phone System enne enne nnns 16 Program the ID Code of a Transmitter 17 Delete Programmed Transmitters Sensors Security Systems 17 TO Arin Disarm the Dialeluuu tac FO edo ctp de me Pe Ene kde 18 Delay Dialing Entry Exit Mode 18 Universal Dial Tone oai L t UR M MEE EE 19 Dial Sequence Setting iier tnr aasma 20 CONNECT THE DIAL ALERT WITH YOUR EXISTING ALARM SYSTEM 21 eiim zc E 22 BATTERY MAINTENANCE Etui oh 23 ec w H S 23 ADDITI
25. r M on the upper left corner If nothing is entered within 5 seconds the display will return to the clock mode 2 Within the first 5 seconds select a memory location by pressing a key pad number 1 9 to store the telephone number 3 Enter the telephone number using the keypad The display will flash as the numbers are being entered To insert a pause period between any digits of the pre programmed telephone number see PROGRAMMING A PAUSE PERIOD page 15 4 Press the key within 5 seconds after the last digit of the telephone number is entered The number is now stored 5 After the telephone number has been stored rEdIAL 3 will appear on the display This is the redial count which is the number of times the dialer will call that telephone number The dialer is factory set to call each number 3 times The number of attempts can be changed to dial 1 to 9 times If you STANDARD PROGRAMMING want to keep the dialer at 3 attempts press the MEM key To change the redial count enter a number from 1 9 when display shows rEdIAL 3 6 Te display will now show YEPEAL 3 This is the repeat which is the mmbercftmes themessage wilb repeated during thane call The dialer is factory set to repect themessage 3 times The nunber of repects can be changed frm 1 to9tmes Tf yowert to keep the repeat mmainac3tmes presstte MEM key Tocharge the repect ater a number firm 1 9 when displ
26. r is activated check phone line connection If unit is powered by AC adapter or powered by back up battery back light stays on for five seconds when any key on the keypad is pressed You have pressed a key in the right order 1 When the dialer is turned on for the first time 2 When the pre programmed transmitters sensors are deleted from the memory You have made a mistake The dialer has been triggered in DELAY mode It gives you time to disarm the dialer before dials the emergency phone number STANDARD PROGRAMMING When you plug in the dialer for the first time you will hear a double beep and all the lights will be on for 2 seconds the keypad will continue to flash and the clock will be set to 12 00 PROGRAM THE TIME CLOCK 1 Press the L key display will show L 2 Press the 4 key display willshow L4 12 00 The first digit of the time will be flashing The flashing digit is the number you are currently changing 3 Using the keypad enter the desired number The clock is in 24 hour mode For example if the display shows L4 1330 the time is set at 1 30 pm To change the time to 8 15 pm the sequence is remember that the clock is in 24 hour mode I4 21 10 I1 15 RECORDING A MESSAGE Currently the keypad is flashing and will continue to flash until a message has been recorded The dialer cannot dial any phone numbers if a message has not been recorded To record a voic
27. riod between phone number and numeric message Press the R P key to insert a pause period between the telephone number and the numeric information you want to send The pause period is the time you have to wait after the connection has been made to the paging company 15 ADVANCED PROGRAMMING and before you can enter the numeric information i e phone number The display will show a P if a pause period is entered This pause period is factory set at 5 seconds but can be changed from 1 9 seconds You may also insert multiple pause periods to suit your application Call the paging company to determine how long the pause period should be To insert a pause period in a telephone number The length of the pause period L can be programmed as shown 1 Press the L key the display will show L 2 Press the key the display will show L 3 the last digit 3 is the setting of the pause period in this example it is currently set to 3 seconds as per chart below To keep this setting press the L key 3 To change the pause period press either 1 2 9 when the display shows L 3 1 1 second 2 2 seconds 3 seconds 4 4 5 5 seconds 6 6 seconds 7 seconds 8 8 seconds 9 9 seconds When programming telephone number to the dialer see STORING TELE PHONE NUMBERS a pause period may be added between any digits of a phone number By using the key on the keypad a
28. t and plug it into W E the LINE jack If you want to have an answering machine on the same line as the dialer thread the phone line through the bottom hole in the back of the unit and plug it into the PHONE jack of the dialer The phone line s must be inserted through the back of the unit before it is attached to the wall 3 Thread the AC adapter cord through the top hole in the back of the unit and plug it into the AC connector on the circuit board as shown The adapter cord must be inserted through the back of the unit before it is attached to the wall 4 Insert the 9 volt battery and rotate the antenna from the inside of the dialer to the outside 5 Firmly close the case Insert and secure the two screws to the bottom case near the two tabs 6 Using the template provided insert the two screws into the wall 7 Gently hang the Dial Alert to these two screws 8 Plug the other end of the telephone cord into a telephone jack Plug the AC adapter into a power outlet The red AC PWR light will turn on and the keypad backlight will flash CAUTION After installation please use two screws included to fix the front and back case together before hang on to the wall When you open the case please remove the AC adapter and the phone line from the wall outlet INSTALLATION Switch Setting 1 Tone Pulse Switch This dialer supports both Tone and Pulse dialing In order to change the setting you
29. when vibration is detected Attach vibration sensor to valuables stereo system antiques 9V alkaline battery included Water Resistant Panic Button Transmitter PT 434 Activates Security Control Panel and Emergency Dialer by pressing the panic button when under duress Ideal for Seniors Handicapped and Disabled Water resistant carry transmitter all the time Operates using lithium batteries included Keypad Control KP 433 Functions as an external keypad or secondary control location Use the keypad to arm disarm the Audio Alarm AA 433 Eliminates the need to walk through your premises to your Security Systems Control Panel Operates using lithium batteries included 25 E B E HW A k d 4 ADDITIONAL ACCESSORIES Smoke Sensor SS 433 Detects sound frequencies of existing smoke carbon monoxide alarms Activates Security Control Panel SC 001 or Emergency Dialer AD 433S when the preset sound frequency is detected 9V alkaline battery included Audio Sensor AS 433 Detects alarm sound from existing security system alarm sends signal to Dial Alert Eliminates need for monitoring service 9V alkaline battery included Keychain Transmitter 4B 433A Activates and deactivate the Audio Alarm AA 433 at the push of a button Reliable design with microcontroller 12V alkaline battery included Garage Door Sensor GS 433 Plac
Download Pdf Manuals
Related Search