Sirius Satellite Radio SRA-40 User's Manual
Contents
1. SINCE 1897 TE RADIO SINCE 1897 Galaxy Style SRA 40 SIRIU 4 Thank you for choosing a Shakespeare product Shakespeare works hard to build reliability and durability into all of its products for maximum customer satisfaction Customer comments are GALAXY pe welcome Before installing please study the diagram and check parts supplied against those listed sinus J IMPORTANT Please read all instructions before installing The Shakespeare Galaxy Style SRA 40 Satellite Radio Antenna is a versatile antenna for receiving Sirius Satellite Radio The antenna s versatile mounting permits attaching the antenna directly to a flat surface to the included Pedestal Mount kit to an optional extension mast 1 14 thread or to a Shakespeare Style 4720 Rail Mount sold separately When the pedestal base is used the kit allows routing the antenna s coax cabling with or without passing the cable through the mounting surface In all cases a receiver capable of receiving Sirius Satellite Radio is required not supplied o Supplied parts 1 SRA 40 Antenna with 6 cable and TNC Female connector 1 25 Coax Cable with TNC Male and SMB connectors The length of the cable run from the antenna to the satellite radio receiver can be extended by using the one of the cable kits listed on page 6 each sold separately Note These cables replace the 25 cable supplied with the antenna and must be used as supplied2. They cannot be lengthened shortened or connected together as extensions 1 Bag containing 1 Extension shaft 1 Lockwasher 1 Retaining nut 1 1 14 Thread Adapter 1 Rubber O ring 1 Surface Mounting Flange 1 Mounting Gasket with knife slit for passing the coax cable 3 Self tapping stainless steel mounting screws This instruction sheet Tools required Screwdriver Marking pencil drill and drill bits 9 16 7 64 needle nose pliers or other tools appropriate to your specific application may also be needed Required materials Silicone Sealer RTV when flush mounting DO NOT CUT OR ALTER THE ANTENNA CABLE DO NOT REMOVE ITS CONNECTOR Step 9 Attach the Thread Adapter with antenna to the Mounting Flange IMPORTANT Rotate the cable counterclockwise while turning the Thread Adapter clockwise Make sure the cable turns freely and does not bind Step 10 Firm up the mounting screws but do not over tighten Skip to Completing the installation on page 5 SRA 40 antenna gpa40 GALAXY sr sIRIUS Thread Adapter Rubber O ring Knockouts 3 120 ZO ONLY ONE Knife slit for passage of cable Mounting Gasket 6 cable and connector DO NOT CUT THE CABLE OR REMOVE THE CONNECTOR Step 3 Secure the antenna to the mounting surface with the supplied retaining nut and lock washer see Figures 2 amp 3 A small bead of RTV around the outer edge of the antenna base i
3. from any metal objects or other structures that could block the line of sight reception of the satellite signal The height of the antenna is not as important as having a clear view of the horizon To determine the best location for the SRA 40 hold the Satellite Shooter template back page horizontally at the chosen mounting location and follow the instructions on the template Scan a full circle with the Shooter to make sure no obstacles block the antenna s view of the sky from overhead The Mounting Flange requires a flat not curved surface or the antenna can be mounted on the 1 14 thread end of a marine antenna extension mast or a Shakespeare Style 4720 Rail Mount each sold separately The antenna s cable can be routed through a hole in the mounting surface through the Mounting Flange or through the extension mast IMPORTANT When mounting to a flat surface using the mounting flange and gasket orient the Mounting Flange so that its cable exit faces the rear of the vessel or vehicle away from oncoming wind due to normal vessel or vehicle motion Mount the SRA 40 so that it does not interfere with safe operation of the vessel or vehicle In choosing how and where to mount the antenna consider the accessibility of the area underneath and whether the area is clear of any wires or other obstructions Choose a convenient pathway for running the coax cable as far as possible from other electrical cables If the distance between the ant
4. anning This edge must be kept horizontal at the mounting location Optional Accessories SRS 1 DC Voltage Splitter for antenna cables up to 50 SRS 2 DC Voltage Splitter for antenna cables over 50 SRC 35 35 RG 58 cable kit with connectors SRC 50 50 RG 58 cable kit with connectors SRC 90 90 RG 8X cable kit with connectors SRC 135 135 RG 8X cable kit with connectors and inline amplifier SM 30 Low Profile Surface Mounting Kit for locations without access under the antenna for attaching nuts and bolts The length of the cable run from the antenna to the satellite radio receiver can be extended by using the one of the optional cable kits listed above Note These cables replace the 25 cable supplied with the antenna and must be used as supplied They cannot be lengthened shortened or connected together as extensions Electronic Products Group 6111Shakespeare Rd Columbia SC 29223 803 227 1590 Fax 803 419 3099 www shakespeare marine com 2005 Shakespeare Co all rights reserved Sirius and related marks are trademarks of Sirius Satellite Radio Inc rev 12 07 2006
5. enna and your Satellite receiver is more than 25 feet special Shakespeare cable kits are available see Optional Accessories back page Acquire the appropriate kit before proceeding SURFACE MOUNTING If you are attaching the antenna directly to a flat surface the cable with its connector attached can be routed through a 9 16 hole drilled in the mounting surface Do not cut the cable and do not remove the connector Step 1 Drill a 9 16 mounting hole For mounting surfaces from 1 4 to 1 thick use the extension shaft supplied Route the 6 antenna lead with TNC female connector through the center of the extension shaft Thread the Extension Shaft onto the existing antenna shaft and tighten Step 2 Pass the connector cable and shaft if used from the SRA 40 through the hole FIGURE 1 FIGURE 2 Direct surface mounting for surfaces up to 1 4 thick Direct surface mounting for surfaces 1 4 1 thick SRA 40 antenna SRA 40 antenna 6 SRA 40 cable can aga 6 SRA 40 Shaft j cable Lo Lock washe Mounting surface Lock washer Mounting surface Retaining nut Retaining nut Cable to receiver Cable to receiver EXTENSION MAST OR RAIL MOUNTING If you are attaching the antenna to a marine extension mast or rail mount Step 1 Route the 6 cable from the antenna through the thread adapter Step 2 Screw the antenna onto the thread adapter Step 3 Route the 25 or optional cable through t
6. he extension mast or rail mount Step 4 Attach the 25 cable s connector to the connector on the 6 antenna cable Step 5 Screw the antenna assembly onto the extension mast or rail mount IMPORTANT Rotate the cable counterclockwise while turning the antenna assembly clockwise Make sure the cable turns freely and does not bind SPECIAL NOTE The hole in ratchet type antenna mounts will not accommodate the SRA 40 s connector You must use the included flange mount a rail mount or an extension mast which will allow the cable and its connector to pass through Do not cut the cable and do not remove the connector Skip to Completing the installation below Completing the installation Step 1 Route the cable to your satellite radio receiver IMPORTANT If your satellite receiver has two antenna input terminals the optional SRS 1 Splitter may be required Newer models may differ so consult your dealer or Shakespeare for up to date information Step 2 Attach the SMB connector to your satellite radio receiver See the receiver s manual for precautions and instructions Done Satellite Shooter Template Trace the triangle below on a sheet of paper then cut out the triangle and use as a template on thick paper or poster board 1 Tape this edge to paper tube or straight edge 2 Sight through tube or top of straight edge for clear view of sky This corner should be next to the mounting hole when sc
7. s nuts or other hardware not supplied Be sure to use only stainless steel hardware If you find it too difficult to start the screws drill 7 64 pilot holes Step 5 Unscrew the Mounting Flange from the Thread Adapter and place the Mounting Gasket in the Mounting Flange Step 6a Attach the Mounting Flange and gasket to the surface oriented according to the mark made in step 2 Use the supplied self tapping screws or other stainless steel hardware not supplied Do not overtighten Step 7a Attach the Thread Adapter with antenna to the Mounting Flange Skip to Completing the installation on page 5 If you are running the cable through the side of the Mounting Flange Follow Steps 2 through 5 above Then Step 6b Use needle nose pliers to break off one of the three cable knockouts in the Mounting Flange as determined and marked in step 2 above The choic of knockout must be determined in step 2 See illustration on page 2 Step 7b Position the cable in the gasket s knife slit while fitting the gasket into position in the Mounting Flange Step 8 LOOSELY attach the Mounting Flange with Gasket to the surface orienting it according to the mark made in step 2 Use the supplied self tapping screws or other stainless steel hardware not supplied Do not overtighten Choose a mounting location The SRA 40 antenna must be mounted horizontally in a location that is open and has a clear view of the sky It must be mounted away
8. s recommended to insure a watertight seal Skip to Completing the installation on page 5 PEDESTAL MOUNTING If you are attaching the antenna pedestal assembly to a flat surface the cable with its connector attached can be routed through a 9 16 hole drilled in the mounting surface or passed through the Mounting Flange Do not cut the cable and do not remove the connector If you are running the cable through the mounting surface Step 1 Drill a 9 16 center hole for the antenna cable When drilling fiberglass surfaces use a small backup block of scrap wood to control push through splintering Use caution to avoid drilling through or near fuel lines fuel tanks hydraulic lines or electrical wiring Step 2 Attach the Thread Adapter to the SRA 40 antenna then attach the Mounting Flange to the Thread Adapter and place the Mounting Gasket in the Mounting Flange refer to the diagram at right Orient the antenna so that the Galaxy name faces forward or otherwise as you prefer Mark a pencil line on the flange and the mouting surface to serve as an index in step 6b Step 3 While holding the Mounting Gasket to the surface lift off the assembly and use the Mounting Gasket as a template to mark locations for the mounting screws Step 4 The supplied mounting screws will accommodate most surfaces If you find them too long too short or otherwise unsuitable for your application substitute wood screws machine screws washer
Download Pdf Manuals
Related Search