Sinclair PG20 User's Manual
Contents
1. Model PG 20 Manual Grommet Machine Operating Manual 800 624 2408 530 626 9386 Fax 530 626 5144 6686 Merchandise Way Diamond Springs Ca 95619 www sinegco com INTRODUCTION MANUAL MACHINE MODEL PG 20 FOR PLACING APPLICATIONS BY HAND The function of this machine is the placement of applications or to punch holes interior diameter of tube grommet 8mm or 12mm in materials that need these applications Specially recommended for placing grommets and washers in awnings curtains advertising signs etc THIS MACHINE WILL PUNCH THE MATERIAL WHILE SIMULTANEOUSLY SETTING THE GROMMET WARNINGS We hope you will take notice of these warnings and we would like to thank you for the purchase of this machine User unawareness of the machine leads on many occasions to elementary doubts about its operation Please read this instruction manual carefully for your guidance in order to make the most of your machine Always use extreme caution when operating machine Keep hands free of cutting surfaces SINCLAIR EQUIPMENT DECLINES ALL RESPONSABILITY ON THE INCORRECT USE OF THIS INSTRUCTION MANUAL PLASTGrommet Grommet Grommet Measurements Washer Measurements 8mm Plastic Grommet A 8mm No washer is used for B 15mm 8mm grommet C 8mm 12mm Plastic Grommet A 12mm A 15mm B 26mm B 24mm C 8 3mm A S KI c Installation of PG 20 Install grommet machine on secure table t2. Try to spin grommet in material If grommet is loose continue to bring die 2 down until grommet is secure in material and won t spin When grommet tension is correct tighten tension nut 1 FIG1 Change Of Dies The PG 20 will take two die sets If you want to change out sizes you will need to replace parts Please refer to the following diagrams 8mm Die Set 12mm Die Set r Only used in 12mm die set Parts Schematic 30 OER O NN Kit complet grommets and washers R AWW Part Description 30 PGR2030 Machine Head 31 PGR2031 Die Holder Pin 32 PGR2032 Driving Stem 33 PGR2033 Driving Stem Guide Wheel Pin 34 PGR2034 Driving Stem Guide Wheel 36 PGR2036 Eccentric Part 37 PGR2037 Connecting Rod 38 PGR2038 Connecting Rod Pin 39 PGR2039 Adjusting Nut For Top Die 40 PGR2040 Screw For Fixing Lever 41 PGR2041 Lever Pin 42 PGR2042 Draw Back Spring 43 PGR2043 Driving Stem Control Part 44 PGR2044 Driving Stem Control Pin 45 PGR2045 Pin For Top Set Spindle 46 PGR2046 Lever 48 PGR2048 Die Holder For Machine 49 PGR2049 Top Die 50 PGR2050 Bottom Die 51 PGR2051 Top Set Spindle 52 PGR2052 Top Set Spindle Spring 58 PGR2058 Screw For Fixing Die Holder NOTES
3. op with the front of machine base flush with table edge Use four bolts with lock nuts washers to secure machine Adjusting both the cutting and the grommet pressure ALWAYS ADJUST FIRST THE CUTTING PRESSURE NEVER TRY DO CUTTING AND SETTING AT THE SAME TIME Each time you change material or change grommet sizes it will be necessary to adjust the pressure for the machine to work properly In order to adjust the cutting pressure Refer to diagram below Loosen lock nut 1 with the supplied punch tool Tighten die 2 close to top with the supplied punch tool Loosen 5 set screw Loosen 6 away from upper die 3 AVOID DAMAGES ON THE DIES IF THE DIES COME TOO CLOSE AND YOU TRY TO SET A GROMMET YOU WILL BREAKE THE EDGE OF THE LOWER ONE While frequently pulling lever adjust 6 up gradually turns until two die pieces 3 amp 4 come together just enough to cut material in use Test cut material to make sure cutting is properly adjusted Tighten set screw 5 In order to adjust the grommet pressure Insert grommet on die 3 as shown in figure 1 below Make sure bottom of grommet is up above bottom of top die No washer is needed for 8mm grommets For 12mm grommets insert washer on die 4 as shown in figure 2 Do a test grommet with the material you are using Slowly loosen 2 die to tighten grommet fit Use 1 4 turns or less at a time
Download Pdf Manuals
Related Search