Shopsmith CD Changer System none User's Manual
Contents
1. Bracket R INSTALLATION 2 Procedure for Vertical Installation Note If the anti vibration spring position has been changed and verified for vertical mounting as shown on page 3 start with step 2 1 tis necessary to change the spring attachment position 1 Remove the lock screws on the side of the set using a Philips screwdriver 2 Tum the spring attachment to the V mark side using a screwdriver 3 Replace the removed screws on the V mark side 2 Attach bracket L and bracket R to each side of the unit using the hexagonal bolts with washer base M5 x 8 Bracket R Hexagonal bolt with washer base Determine the mounting location and aril Tour mounting holes Never mount the unit near the fuel tank Drillholes 4mmin diameter 4 Mount the unit in place using four self tapping screws M5 x 12 Use RTV silicone sealer on screw threads or around the holes to prevent moisture intrusion Selt tapping screw M5 12 WIRING output 89 1MHz or 88 7 2 1 Antenna socket To 12V ACC Speaker DIN connection cord 6 pin car antenna FM Modulator 12 volt Accessory Switched ORANGE WHITE STRIPE Connect this wire to a point which is energized when the ignition switch is tumed to the ON or ACCESSORY position 12 volt Constant2. ELECTRONICS INSTALLATION MANUAL HOLD FOR DELCO APPROVAL NEW LOGO Form 128 4487 Rev A Replaced old Delco Logo with New 2 1 95 10 DISC AUTO CHANGER COMPACT DISC CHANGER SYSTEM with COMMANDER amp FM MODULATOR 11 51584483 PACKING LIST MAIN UNIT Commander Changer INSTALLATION PARTS Bracket L Bracket R FM Modulator Hexagonal bolt with washer 0 5 8 B 4 1 Tapping screw Tapping screw Din 8 pin Seal M5 x 12 M3 x 12 cable oo o x4 x2 5 1 1 OTHER ACCESSORIES CD Magazine Index seal sheet Installation Owner s A Manual guide 4 1 1 x1 1 BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is locked into place during shipment by the transport screws Be sure to remove the screws prior to installation Caution After removing the transport lock screws place the supplied seals over the screw holes These seals are used to keep dust out of the unit which could cause a malfunction Installation and Wiring Precautions To prevent a short circuit sure to turn off the ignition and remove the negative battery cable prior to installation Connect power wires last Note Ifthe changer is to be installed in a car that is equipped with an on board drive or navigation computer do not disconnect the battery cable Ifthe cable is disconnected the computer
3. GREEN WHITE STRIPE Connect this lead to the cable to which power is continu ously supplied and which has been passed through the vehicle s fuse block Ground BLACK Screw this to metal partofthe vehicle Clean connecting area of paint dirt etc Poor ground can cause damage and affect playability Display Unit FM Radio DIN cable INTERFERENCE 89 1 MHz changer Ifa clear signal cannot be obtained on 89 1 MHz change the position of the frequency select switch on the back of the FM Modulator and tune the radio to 88 7 MHz when using the CD changer Select a frequency before mounting the FM Modulator Radio sensitivity is slightly reduced when the FM Modulator is connected Installation of the FM Modulator Install the FM Modulator to the mounting surface with the included tapping screws M3 12 Display unit FM Modulator 5 WIRING DIAGRAM Features Shuffle Play Conveniently shuffles the tracks on the disc selected entire 10 discs giving the user a different concert mix every time Disc Select Easily moves up or down discs with the disc select buttons Track Search Advances to the next track on the disc or returns to the beginning of the current track Track Disc Repeat current track or disc Allows user to play favorite CD or songs Repeat over Track Disc Preview tracks and disc for 10 sec
4. anger Identity Switch INSTALLATION 1 The unit can be installed vertically or horizontally The position of the built in anti vibration springs left and right side must correspond to the mounting position chosen If the springs are not set correctly for the type of installation chosen the anti vibration compensation will not be effective Horizontal Installation Vertical Installation lote The unit is shipped with the springs installed for horizontal installa 18 necessary to change the spring attachment position 1 Remove the lock screws on the side of the set using Phillips screwdriver 2 Turn the spring attachment to the V mark side using a screw driver 3 Replace the removed screws on the V mark side Procedure for Horizontal Installation 1 Attach bracket L and bracket R to each side of the unit using the hexagonal bolts with washer base M5 8 Se A Hexagonal bolt with washer base M5x8 2 Determine the mounting location and drill four mounting holes Never mount the unit near the fuel tank Drill holes 4mm in diameter Secure the unit in place using four sett tapping screws M5 x 12 Use RTV silicone sealer on screw threads around h the holes to prevent moisture intrusion Self tapping screw MS x 12 T
5. memory may be lost Under these conditions use extra caution during installation ot to cause a short circuit 2 Po not install the unit in the following locations Locations exposed to direct sunlight Where hot air is discharged from the car heater In areas subject to extreme temperatures Incorrect installation can cause the sound to skip when playing a disc Mount the unit firmly in place using the supplied brackets and screws Be careful not to damage the car wiring Be sure to use the supplied screws Be careful not to snag any wires when tightening screws Do not use any of the screws that are part of the brake or steering system to install the unit a _Installthe unit as closely to vertically or horizontally as possible If the unit must be inclined the angle must be 15 or less Installation and inclination angle Horizontal mounting Vertical mounting Installation rE 15 Angle 4 7 10 Identity Switch for 204 CD Changer When used with a compatible controller an additional CD changer can be installed When an additional CD changer has been attached in this fashion the ID switch is used to indicate the number of each respective changer unit Changer Identity Switch Do not use this switch if only 1 CD changer is being used Refer to the manual of the divider unit for further details on 2 changer operation Ch
6. ond per selection until you reach the Scan desired Wired Remote Eliminates the possibility of remote loss Easy to locate Conveniently backlit Warranty One year limited GM warranty Delco Electronics 10 Disc Changer Part 12344632 Also requires applicable antenna adapters listed All Geo s through 1995 Pre 1988 GM most Domestic and Foreign Vehicles No adapters required 1988 1993 Vehicles with 12 Pin Radios No adapters required 1988 1993 Vehicles with 21 Pin Radios Require the following adapters one each GM Part 16056152 GM Part 16047347 1994 amp 1995 Vehicles Require the following adapters one each GM Part 16169591 GM Part 16169611 For more information on the 10 Disc Changer please contact Delco Electronics at 1 800 428 0501 16213708 PELET lt 2 95
Download Pdf Manuals
Related Search