Sharp Projector Remote Control User's Manual
Contents
1. PROJI PROJ2 PROJI PROJ2 Enter Preset View Ese CPU CPU VIDEO VIDEO Audio output 3 1 3 2 3 3 3 4 3 5 3 6 Power should be ON button lit Deselect all buttons under the labels CONTROL and I O lights above buttons should be OFF Under the label I O Select the button RGBS light should come on Select button CPU1 or CPU2 depending on which wall jack the computer is connected to red light should come on If any green lights come on elsewhere on the switcher deselect those buttons Select button above label for projector output to be used for computer image projection Proji CPU or Proj2 CPU PROJ1 CPU button is for the projector nearest the classroom door PROJ2 CPU button is for the projector nearest the windows 15 RGBS Audio Both projectors can be chosen if both screens are being used for display 3 7 Press ENTER button on the right side of switcher under Control label 4 0 Projector Remote Control Should be on classroom podium Note remote control does not work well with fluorescent lights on 4 1 4 2 4 3 Take the remote control point it towards the projector you are using and press the blue button on the upper left hand corner This is the power button It will take up to a minute for the projector to warm up There will be both solid and flashing green lights on the projector Once there are 2 solid green lights on the projector indicating2. Select the button RGBS 3 4 Select button VCR1 for VHS VCR or VCR2 for U Matic or LDP1 for Laserdisc 3 5 If any green lights come on elsewhere on the switcher deselect those buttons 3 6 Select button above label for projector output to be used for video projection Proji VIDEO or Proj2 VIDEO PROJ1 VIDEO button for projector nearest the classroom door PROJ2 VIDEO button for projector nearest the windows Both projectors can be chosen if both screens are being used for display 3 7 Press ENTER The following additional steps are necessary for audio output The volume knob on the PRIMARY CONTROL is for the ceiling speakers The volume knob on the RECEIVER is for the speakers on either side of the whiteboard 4 0 On SWITCHER 4 1 Under the VO label Deselect the RGBS button 4 2 Under the I O label Select the Audio button 4 3 Select button VCR1 for VHS VCR or VCR2 for U Matic or LDP1 for Laserdisc 4 4 Select button above label for PROJ1 CPU Audio output 4 5 Press ENTER 5 0 Projector Remote Control Should be on classroom podium Note remote control does not work well with fluorescent lights on 5 1 Turn off the fluorescent lights since the remote control will not work properly with those lights on 52 Take the remote control point it towards the projector you are using and press the blue button on the upper left hand corner This is the power button It will take up to 24 a minute for the proje
3. for U Matic or LDP1 for Laserdisc 6 4 Select button above label for PROJ1 CPU Audio output 6 5 Press ENTER 70 Projector Remote Control Should be on classroom podium Note remote control does not work well with fluorescent lights on 7 1 Take the remote control point it towards the projector you are using and press the blue button on the upper left hand corner This is the power button It will take up to a minute for the projector to warm up There will be both solid and flashing green lights on the projector 7 2 Once there are 2 solid green lights on the projector indicating that it has warmed up press the button labeled VIDEO Ifthe projector is not warmed up it will not come on Try pressing VIDEO once again if the projector is warmed up but there is still no image on the screen 7 3 If you no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will turn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes 19 for it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again 8 0 On VCR U Matic or Laserdisc Console 2 8 1 8 2 Power ON to VCR1 VHS VCR VCR2 U Matic or LDP1 Laserdisc Insert and s
4. on the projector cart Setting up and Displaying the Mobile Workstations in Room 111 Cheat Sheet Brief instructions for using the Room 111 mounted projectors to display images and output sound from the Lab s PC and Mac mobile workstations These instructions assume that you have connected all of the workstation s cables For complete setup instructions see Setting Up and Displaying Mobile Workstations in Room 111 Step by Step 10 On PRIMARY CONTROL Console 1 14 12 Power ON Ceiling speakers ON 2 0 On RECEIVER Console 1 24 22 Power ON Select SWITCHER displayed text DVD TV 3 0 On SWITCHER Console 1 34 32 33 34 35 3 6 Power ON Deselect all buttons under the labels CONTROL and I O Under the label I O Select the button RGBS Select button CPU1 or CPU2 depending on which wall jack the computer is connected to If any green lights come on elsewhere on the switcher deselect those buttons Select button above label for projector output to be used for computer image projection Proji CPU or Proj2 CPU PROJ1 CPU button for projector nearest the classroom door PROJ2 CPU button for projector nearest the windows Both projectors can be chosen if both screens are being used for display 3 7 Press ENTER 4 0 Projector Remote Comrot Stroud be 071 Classroom pottar Note remote control does not work well with fluorescent lights on 44 42 Take the remote control point it
5. that it has warmed up you should see the computer s image on the screen if the projector is not warmed up there will be no image on the screen f the projector is warmed up but there is still no image press the button labeled COMPUTER Try pressing COMPUTER once again if there is still no image on the screen f you no longer need the projector or if it will be turned off for more han 10 minutes press the blue power button on the remote This will urn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes for it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again 16 The following additional steps are necessary only if AUDIO OUTPUT is required Please note that the speaker wire kept in the cart s black basket needs to connected to either the CPU1 or CPU2 wall plate from the workstation s speaker port green colored port on PC Please Note The volume knob on the PRIMARY CONTROL is for the ceiling speakers The volume knob on the RECEIVER is for the speakers on either side of the whiteboard 5 0 On SWITCHER 5 1 5 2 5 3 5 4 5 5 Under the I O label Deselect the RGBS button light should go off Under the I O label Select the Audio button light should come on Select the
6. towards the projector you are using and press the blue button on the upper left hand corner This is the power button It will take up to a minute for the projector to warm up There will be both solid and flashing green lights on the projector Once there are 2 solid green lights on the projector indicating that it has warmed up you should see the computer s image on the screen ifthe projector is not warmed up there will be no image on the screen If the projector is warmed up but there is Still no image press the button labeled COMPUTER Try pressing COMPUTER once again if there is still no image on the screen 10 4 3 If you no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will turn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes for it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again The following additional steps are necessary only if AUDIO OUTPUT is required Please note that the speaker wire kept in the cart s black basket needs to be connected to either the CPU1 or CPU2 wall plate from the workstation s speaker port green colored port on PC The volume knob on the PRIMARY CONTROL is for the ceili
7. CPU VIDEO VIDEO Audio output 3 1 Power should be ON button lit 3 2 Deselect all buttons under the labels CONTROL and I O lights above buttons should be OFF 3 3 Under the label I O Select the button RGBS light should come on 3 4 Select button VCR1 for VHS VCR or VCR2 for U Matic or LDP1 for Laserdisc red light should come on 3 5 If any green lights come on elsewhere on the switcher deselect those buttons 3 6 Select button above label for projector output to be used for video projection Proji VIDEO or Proj2 VIDEO PROJ1 VIDEO button is for the projector nearest the classroom door PROJ2 VIDEO button is for the projector nearest the windows Both projectors can be chosen if both screens are being used for display 27 3 7 Press ENTER button on the right side of switcher under Control label The following additional steps in Section 4 are necessary for audio output The volume knob on the PRIMARY CONTROL is for the ceiling speakers The volume knob on the RECEIVER is for the speakers on either side of the whiteboard 4 0 On SWITCHER 4 1 Under the I O label Deselect the RGBS button light should go off 4 2 Under the VO label Select the Audio button light should come on 4 3 Select button VCR1 for VHS VCR or VCR2 for U Matic or LDP1 for Laserdisc red light should come on 4 4 Select button abov
8. CPU1 or CPU2 button depending on which wall jack the computer cable is connected to CPU1 or CPU2 red light should come on Select button above label for PROJ1 CPU Audio output lower left hand corner of switcher Press ENTER right side of switcher 6 0 Clean up 6 1 6 2 6 3 Power OFF to Projectors Power OFF to PRIMARY CONTROL Power Off to Workstation 6 4 Disconnect all cables but DO NOT disconnect the extension cables from either the cpu or the monitor cable 17 Setting Up and Displaying Mobile Workstations amp Video Output Simultaneously in Room 111 Brief instructions for using the Room 111 mounted projectors to simultaneously display images from one ofthe Lab s mobile workstations and from the room s VHS video recorder player the U Matic video player or the laserdisc player These instructions assume that you have connected all of the workstation s cables For complete setup instructions see MOBILE WORKSTATIONS in 111 Step by Step and VIDEO OUTPUT in 111 Step by Step STEPS 1 4 ARE FOR COMPUTER SETUP STEPS 5 8 ARE FOR VIDEO SETUP 1 0 On PRIMARY CONTROL Console 1 14 12 Power ON Ceiling speakers ON 2 0 On RECEIVER Console 1 24 22 Power ON Select SWITCHER displayed text DVD TV 3 0 On SWITCHER Console 1 34 32 33 34 35 3 6 Power ON Deselect all buttons under the labels CONTROL and I O Under the label I O Select the button RGBS Select butto
9. ct the extension cable which is attached to the monitor cable to the OUT port on the projector Use the beige extension cables kept on the cart if more room is needed between the computer and the projector Connect the projector s power cord from the projector to an outlet You may need to use an extension cord Power ON to computer Power on to Sharp in two steps a turn on the power switch on the back of projector l b press the power button on the top ofthe projector JL or the ON button on the remote Note that the remote will not work well with the fluorescent lights on After turning on the projector you will see a solid and a flashing green light on its top indicating that the projector is warming up takes about 1 minute When both lights are solid green then the projector is warmed up 2 0 Adjusting Height and Focus 24 22 The height of the projected image is adjustable using the two feet at the front of the projector which will drop down by pressing the purple buttons on the front The feet can also be moved by screwing unscrewing them To FOCUS turn the outer ring around the lens for a sharper image 3 0 Remote Contro Additional Features Hemote should be with the projector Note remote control does not work well with fluorescent lights on 34 If you no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will turn off the
10. ctor to warm up There will be both solid and flashing green lights on the projector 5 3 Once there are 2 solid green lights on the projector indicating that it has warmed up press the button labeled VIDEO Ifthe projector is not warmed up it will not come on Try pressing VIDEO once again if the projector is warmed up but there is still no image on the screen 54 Ifyou no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will turn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes for itto cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again 6 0 On VCR U Matic or Laserdisc Console 2 6 1 Power ON to VCR1 VHS VCR VCR2 U Matic or LDP1 Laserdisc 6 2 Insert and start playing video or disc 7 0 Clean up 7 4 Power OFF to Projectors 7 2 Remove video or disc from player 73 Power OFF to PRIMARY CONTROL 25 Using Video Output in Room 111 Step by Step Instructions for using the Room 111 mounted projectors to display images and output sound from the room s VHS video recorder player the U Matic video player and the laserdisc player 0 0 Initial setup 0 1 Look on the south wall the wall with the whiteboar
11. d on it On the left hand side is a set of light switches see Figure AJ Figure A screens These switches are These switches This switch for bringing the right turn the dims and and left projector Fl u o resce nt brightens the screens down lights on and off oval ceiling lights 1 0___ On PRIMARY CONTROL Console 1 This provides power to all of the components in the console and to the ceiling speakers It does not control power to the projector The volume knobs control the ceiling speakers 11 Select Power ON button lit 12 Select Ceiling speakers ON button lit 2 0 On RECEIVER Console 1 The Receiver works in tandem with the Switcher see next step where you choose the source of the image and or sound to be projected The volume knob on the Receiver controls the speakers at the front of the room 2 1 RECEIVER should be ON text is shown in display window 2 2 Select SWITCHER button displayed text DVD TV 3 0 On SWITCHER Console 1 see Image below and Figure Al Here you first select the source of the video to be projected either VCR1 VCR2 or LDP1 Then you select which projector will display the image from computer either PROJ1A IDEO PROJ2A IDEO or BOTH You also use the Switcher to output sound 26 Figure Switcher CPUI CPU2 VCRI VCR2 LDPI LDBOBOBdUJgaagadauu amp C oo0ogoo Poo oo PROJI PROJ2 PROJI PROI2 Enter Preset View Ese RGBS Audio CPU
12. e label for PROJ1 CPU Audio output lower left hand corner of switcher 4 5 Press ENTER right side of switcher 5 0 Projector Remote Control Should be on classroom podium Note remote control does not work well with fluorescent lights on 5 1 Take the remote control point it towards the projector you are using and press the blue button on the upper left hand corner This is the power button It will take up to a minute for the projector to warm up There will be both solid and flashing green lights on the projector 5 2 Once there are 2 solid green lights on the projector indicating that it has warmed up press the button labeled VIDEO f the projector is not warmed up it will not come on Try pressing VIDEO once again if the projector is warmed up but there is still no image on the screen 5 3 If you no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will turn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes for it to cool down and can be turned back on when you see a solid red light on the projector 28 To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again 6 0 On VCR U Matic or Laserdisc Console 2 6 1 Power ON to VCR1 VHS VCR VCR2 U Matic or LDP1 Laserdisc 6 2 In
13. er This is the power button It will take up to a minute for the projector to warm up There will be both solid and flashing green lights on the projector Once there are 2 solid green lights on the projector indicating that it has warmed up you should see the computer s image on the screen ifthe projector is not warmed up there will be no image on the screen f the projector is warmed up but there is still no image press the button labeled COMPUTER Try pressing COMPUTER once again if here is still no image on the screen If you no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will urn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes for it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again If images are only being displayed on either the laptop or the room screens but you want to simultaneously display an image on both try the following Press F N Function key and F3 Pressing this combination of keys should act as a toggle enabling an image to displayed 1 only on the laptop s screen OR 2 only on the room s screen OR 3 on both screens simultaneously The following additional steps are necessary
14. ere adapter needed 0 5 Connect the extension that is attached to the monitor cable to the shorter length of the split dark gray cable 0 6 Connect the other side of the split dark gray cable to CPU1 or CPU2 0 7 Once all cables are connected turn on workstation and monitor 10 On PRIMARY CONTROL Console 1 This provides power to all of the components in the console and to the ceiling speakers It does not control power to the projector The volume knobs control the ceiling speakers 11 Select Power ON button lit 12 Select Ceiling speakers ON button lit 2 0 On RECEIVER Console 1 The Receiver works in tandem with the Switcher see next step where you choose the source of the image and or sound to be projected The volume knob on the Receiver controls the speakers at the front of the room 2 4 RECEIVER should be ON text is shown in display window 2 2 Select SWITCHER button displayed text DVD TV 3 0 On SWITCHER Console 1 see Image below and Figure Cl Here you first select the source of the computer image to be projected either CPU1 or CPU2 Then you select which projector will display the image from 14 Figure C computer either PROJ1 CPU PROJ2 CPU or BOTH Ifneeded you can also use the Switcher to output sound from a computer Switcher CPUL CPU2 VCRI VCR2 LDPI yo Power mil Lg J
15. ing the two feet at the front of the projector which will drop down by pressing the black buttons on the front The feet can also be moved by screwing unscrewing them To FOCUS follow these steps a On either the top of the projector or the remote press ZOOM FOCUS which toggles between the zoom function and focus Select FOCUS b After selecting FOCUS use to sharpen the image 3 0 Remote Control Ad nal Features Remote should be with the projector Note remote control does not work well with fluorescent lights on 3 1 If you no longer need the projector or if it will be turned off for more than 10 minutes press the blue power button on the remote This will turn off the projector Please note that you cannot immediately turn the projector back on It takes a few minutes for it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again If AUDIO OUTPUT from the workstation is needed then you will have to use the speakers kept in the storage basket on the cart 4 0 Clean up 4 1 Power OFF to Projector You will need to press either the projector s power button or the one on the remote followed by turning off the MAIN 4 2 Power OFF to computer 4 3 Disconnect all cables Make sure that the projector s remote and the black RGB cable stay
16. is shown in display window 3 2 Select SWITCHER button displayed text DVD TV 4 0 On SWITCHER Console 1 see Image below and Figure BI Figure B CPUL CPU2 VCRI VCR2 LDPI Control vo Power PROJI PROJ2 PROJI PROJ2 Enter Preset View Esc RGBS Audio CPU CPU VIDEO VIDEO Audio output 4 1 Power should be ON button lit 4 2 Deselect all buttons under the labels CONTROL and I O lights above buttons should be OFF 4 3 Under the label I O Select the button RGBS light should come on 4 4 Select button CPU1 or CPU2 red light should come on 4 5 If any green lights come on elsewhere on the switcher deselect those buttons 4 6 Select button above label for projector output to be used for computer image projection Proji CPU or Proj2 CPU e PROJ1 CPU button is for the projector nearest the classroom door PROJ2 CPU button is for the projector nearest the windows Both projectors can be chosen if both screens are being used for display 4 7 Press ENTER button on the right side of switcher under Control label 5 0 Projector Remote Control Should be on classroom podium Note remote control does not work well with fluorescent lights on 54 52 53 Take the remote control point it towards the projector you are using and press the blue button on the upper left hand corn
17. it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press MUTE on the remote Projector will turn itself back automatically in 10 minutes or when you press MUTE again 5 0 On SWITCHER Console 1 5 1 Power should still be ON 5 2 Deselect all buttons under the labels CONTROL and I O 5 3 Under the label I O Select the button RGBS 5 4 Select button VCR1 for VHS VCR or VCR2 for U Matic or LDP1 for Laserdisc 5 5 If any green lights come on elsewhere on the switcher deselect those buttons 5 6 Select button above label for projector output to be used for video projection Proji VIDEO or Proj2 VIDEO You cannot choose the same projector chosen to display the computer s images PROJ1 VIDEO button for projector nearest the classroom door PROJ2 VIDEO button for projector nearest the windows Only one projector can be chosen to display video images 57 Press ENTER The following additional steps are necessary for audio output The volume knob on the PRIMARY CONTROL is forthe ceiling speakers The volume knob on the RECEIVER is for the speakers on either side ofthe whiteboard When showing simultaneous video and computer images AUDIO OUTPUT is only possible from the video source 6 0 On SWITCHER 6 1 Under the I O label Deselect the RGBS button 6 2 Under the I O label Select the Audio button 6 3 Select button VCR1 for VHS VCR or VCR2
18. n CPU1 or CPU2 depending on which wall jack the computer is connected to If any green lights come on elsewhere on the switcher deselect those buttons Select button above label for projector output to be used for computer image projection Proji CPU or Proj2 CPU PROJ1 CPU button for projector nearest the classroom door PROJ2 CPU button for projector nearest the windows Only one projector can be chosen to display images from the computer 3 7 4 0 Projector Remote Control Should be one Press ENTER classroom Note remote control does not work well with fluorescent lights on 44 42 43 Aim the remote control at the projector you are using and press the blue power button on the upper left hand corner It will take up to a minute for the projector to warm up There will be both solid and flashing green lights on the projector Once there are 2 solid green lights on the projector indicating that it has warmed up you should see the computer s image on the screen ifthe projector is not warmed up there will be no image on the screen If the projector is warmed up but there is Still no image press the button labeled COMPUTER Try pressing COMPUTER once again if there is still no image on the screen If you no longer need the projector or if it will be turned off for more than 10 minutes turn the projector off Please note that you cannot immediately turn the projector 18 back on It takes a few minutes for
19. nect the projector s black RGB cable a one end to the COMPUTER 1 IN port on projector b the other end to the extension cable leading to the monitor port on the cpu Connect the monitor cable to the COMPUTER OUT port on the projector Use the beige extension cables kept on the cart if more room is needed between the computer and the projector Connect the projector s power cord from the AC IN port on the projector to the power strip on the cart Plug the power strip cord into an outlet or into the power strip on the back of the workstation Power ON to computer Power on to Mitsubishi in two steps a turn on MAIN power switch on side of projector f s b press the power button on the top of the projector uj or the blue power button on the remote Note that the remote will not work well with the fluorescent lights on After turning on the projector you will see a solid and a flashing green light on its top indicating that the projector is warming up takes about 1 minute When both lights are solid green then the projector is warmed up and you should see the computer s image on the screen if the projector is not warmed up there will be no image on the screen Ifthe projector is warmed up but there is still no image press the button labeled COMPUTER Try pressing COMPUTER once again if there is still no image on the screen 2 0 Adjusting Height and Focus 24 22 The height of the projected image is adjustable us
20. ng speakers The volume knob on the RECEIVER is for the speakers on either side ofthe whiteboard 5 0 On SWITCHER 5 1 Under the I O label Deselect the RGBS button 5 2 Under the I O label Select the Audio button 5 3 Select the CPU1 or CPU2 button depending on which wall jack the computer cable is connected to CPU1 or CPU2 5 4 Select button above label for PROJ1 CPU Audio output 5 5 Press ENTER 6 0 Clean up 6 1 Power OFF to Projectors 6 2 Power OFF to PRIMARY CONTROL 6 3 Power Off to Workstation 6 4 Disconnect all cables 1 Setting up and Displaying the Mobile Workstations in Room 111 Step by Step Instructions for using the Room 111 mounted projectors to display images and output sound from the Lab s PC and Mac mobile workstations 0 0___Initial setup 0 1 0 2 Move computer into 111 with the following items on the cart or in the cart s basket Each mobile workstation has its own set of labeled cables for 111 2 beige extension cables 1 attached to the cpu adapter needed for Mac 1 attached to the monitor cable These extensions should remain connected to the cpu and the monitor cable since they allow more flexibility in positioning the workstation These cables can also be used with the mobile projectors A split dark gray cable with one end that connects to the wall jack and a a short length that connects to the extension leading to the monitor cable and b a longer length that connects t
21. o the extension leading to the cpu This cable is only used in 111 Athin black cable that connects the wall jack speaker port with the speaker port on the cpu This cable is only used in 111 See Figure A Two wall jacks are beneath the white board near the podium one labeled CPU 1 the other CPU 2 These are the jacks to connect the projectors to the computers using the split dark gray cable Either jack may be used To their right of are two jacks labeled 101D1 and 101D2 These jacks are for connecting the computers to the network including Internet access via network cables and either may be used no matter whether CPU 1 OR CPU2 is used Plug the computer s power cord into the wall outlet to the right of the 101D1 and 101D2 jacks 12 Figure A CPU2 CPUI Wall Jacks on south wall Power cord outlets 0 3 Confirm that the network cable is connected securely from the back of the computer to either the 101D1 or 101D2 outlet 0 4 Connect the extension cable attached to the cpu to the longer length of the split dark gray cable see Figure B Figure B PC Computer Extension from cpu connects here Network cable connection 13 Macintosh o o x Network connection Extension from cpu connects h
22. only if audio output is required the speaker wire which is attached to the cable kept on the podium needs to connected to either the CPU1 or CPU2 wall plate from the workstation Please Note The volume knob on the PRIMARY CONTROL is for the ceiling speakers The volume knob on the RECEIVER is for the speakers on either side of the whiteboard 6 0 On SWITCHER 6 1 Under the I O label Deselect the RGBS button light should go off 6 2 Under the l O label Select the Audio button light should come on 6 3 Select the CPU1 or CPU2 button depending on which wall jack the computer cable is connected to CPU1 or CPU2 red light should come on 6 4 Select button above label for PROJ1 CPU Audio output lower left hand corner of switcher 6 5 Press ENTER right side of switcher 7 0 Clean up 7 3 Power OFF to Projectors 7 2 Power OFF to PRIMARY CONTROL 7 8 Power Off to laptop 7 4 Disconnect all cables The laptop cable used to connect the computer to the wall jack must stay on the classroom s podium Using the Mitsubishi Portable Projector Cheat Sheet Brief instructions on setting up and projecting using the Mitsubishi portable projector in any room 1 0 Setup 14 12 Connect computer s network cable and plug in its power cord Connect extension cables kept with workstation if not already connected 8 one extension to monitor port on cpu adapter needed with Mac b the other extension to the monitor cable Con
23. owe A B Audio visual equipment setup guide ucla department of information studies multimedia and information technology lab written by david cappoli and todd boostrom 8 2000 Table of Contents Using the Cassette Player in Room 111 Cheat Sheet Setting Up and Displaying a Laptop Computer in Room 111 Using the Mitsubishi Portable Projector Setting Up and Displaying Mobile Workstations in Room 111 Cheat Sheet Setting Up and Displaying Mobile Work ions in Room 111 Step Setting Up and Displaying Mobile Workstations amp Video Output Simultaneously Using the P A System in Room 111 Using the Sharp Portable Projector Cheat Sheet Using Video Output in Room 111 Cheat Sheet Using Video Output in Room 111 Step by Step 10 12 18 21 22 24 26 Using the Cassette Player in Room 1 1 1 Cheat Sheet Brief instructions on using the stationary cassette player in room 111 10 On PRIMARY CONTROL Console 1 11 Select Power ON button lit 12 Select Ceiling speakers ON button lit 2 0 On RECEIVER Console 1 2 1 RECEIVER should be ON text is shown in display window 2 2 Select TAPE DECK button displayed text TAPE Please Note The volume knob on the PRIMARY CONTROL is for the ceiling speakers The volume knob on the RECEIVER is for the speakers on either side of the whiteboard 3 0 On TAPE DECK Console 1 3 1 TAPE DECK should be ON lights are on 3 2 Insert and play tape 4 0 Clean u
24. p 4 1 Remove cassette from TAPE DECK 4 2 Power OFF to PRIMARY CONTROL Setting Up and Displaying Laptop Computers in Room 111 Instructions on setting up and projecting a laptop computer display in room 111 Please note that most laptops cannot be connected to the network and may not be able to access the Internet Contact Justin or David for more info 10 lnitial setup 11 Be sure to have the dark gray cable which has both monitor and Speaker connections on each end and which is labeled for laptops kept on the podium in Room 111 12 The laptop should be kept on or by the podium so that the cable can easily reach the wall jacks 13 Two wall jacks are beneath the white board near the podium one is labeled CPU 1 the other CPU 2 These are the jacks to connect the projectors to the laptop using the dark gray cable Either jack may be used The wall jacks labeled 101D1 and 101D2 are for network connections and often cannot be used with laptops Contact Justin or David Plug the computer s power cord into the wall outlet to the right of the 01D1 and 101D2 jacks 14 Connect one end of the dark gray cable to the back of the laptop Connect the other end to CPU1 or CPU2 and the speaker port 15 Once all cables are connected turn on laptop 2 0 On PRIMARY CONTROL Console 1 2 1 Select Power ON button lit 2 2 Select Ceiling speakers ON button lit 3 0 On RECEIVER Console 1 3 1 RECEIVER should be ON text
25. projector Please note that you cannot immediately turn the projector back on It takes a few minutes 22 for it to cool down and can be turned back on when you see a solid red light on the projector To temporarily turn projector off press BLACK SCREEN on the remote Projector will turn itself back automatically in 10 minutes or when you press BLACK SCREEN again f AUDIO OUTPUT from the workstation is needed then you will have to use the speakers kept in the storage basket on the cart 4 0 Clean up 4 1 Power OFF to Projector You will need to press either the projector s power button or the one on the remote followed by turning off the back power button 4 2 Power OFF to computer 4 3 Disconnect all cables Make sure that the projector s remote and the black SHARP MONITOR cable stay on the projector cart 23 Using Video Output in Room 111 Cheat Sheet Brief instructions for using the Room 111 mounted projectors to display images and output sound from the room s VHS video recorder player the U Matic video player and the laserdisc player For complete setup instructions see Using Video Output in Room 111 Step by Step 1 0 On PRIMARY CONTROL Console 1 11 Power ON 12 Ceiling speakers ON 2 0 On RECEIVER Console 1 2 1 Power ON 2 2 Select SWITCHER displayed text DVD TV 3 0 On SWITCHER Console 1 3 1 Power ON 3 2 Deselect all buttons under the labels CONTROL and I O 3 3 Under the label I O
26. sert and start playing video or disc Z0 Clean up 7 1 Power OFF to Projectors 7 2 Remove video or disc from player 7 3 Power OFF to PRIMARY CONTROL 29
27. tart playing video or disc 9 0 Clean up 9 1 92 92 93 94 Power OFF to Projectors Remove video or disc from player Power OFF to PRIMARY CONTROL Power Off to Workstation Disconnect all cables but DO NOT disconnect the extension cables from either the cpu or the monitor cable 20 Using the P A System in Room 1 1 1 Cheat Sheet Instructions for using the Room 111 public address system 10 On PRIMARY CONTROL Console 1 11 Select Power ON button lit 12 Select P A SYSTEM ON button lit This button is also on the room s podium Please Note The volume knobs on the PRIMARY CONTROL are for the ceiling speakers The volume knob on the RECEIVER does not work with the public address system 2 0 Clean up 2 44 Power OFF to P A SYSTEM 2 2 Power OFF to PRIMARY CONTROL 21 Using The Sharp Portable Projector Cheat Sheet Brief instructions for using the Sharp portable projector to display images from the Lab s PC and Mac mobile workstations 1 0 Setup 14 12 Connect computer s network cable and plug in its power cord Connect extension cables kept with workstation if not already connected 8 one extension to monitor port on cpu adapter needed with Mac b the other extension to the monitor cable Connect the projector s black SHARP MONITOR cable a one end to the COMPUTER RGB IN 1 port on projector b the other end to the extension cable leading to the monitor port on the cpu Conne
Download Pdf Manuals
Related Search