SECO-LARM USA EV-2221-P3BQ User's Manual
Contents
1. part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special c2. SECO LARM Indoor IR Dome Cameras Manual NTSC 3 6mm 2 8 11mm DC auto iris 3 6mm 2 8 11mm DC auto iris PAL EV 2221 P3BQ 420 TV lines 3 6mm EV 2221 PKBQ 420 TV lines 2 8 11mm DC auto iris EV 2801 P3BQ 540 TV lines 3 6mm EV 2801 PKBQ 540 TV lines 2 8 11mm DC auto iris SLI FE CE Note Products with model numbers that end with Q or that have a round green Q sticker are ROHS SECO LARM Indoor IR Dome Cameras Specifications NTSC 2221 N3BQ 2221 NKBQ 2801 N3BQ 2801 NKBQ Type Indoor IR Dome Camera 1 3 SONY Super HAD II IR range 65ft 20m Pickup elements Video output 1Vp p composite video 75Q Shutter control Auto Electric DC Auto Iris Auto Electric DC Auto Iris Shutter Shutter Gain control At White balance Operating voltage 12VDC 10 Current LEDs OFF 100mA draw LEDs ON 250mA Operating temperature 4 122 F 20 50 C 51 4 x33 4 133x95 mm Weight 10 0z 283g Parts List 1 x Camera 3 x Mounting screws 1 x DC plug with 1 x Manual 3 x Screw anchors terminal block Dimensions Adjusting the Camera Angle 51 4 133mm Move the camera along its 3 axes to adjust the pan tilt or rotation 2 SECO LARM U S A Inc SECO LARM Indoor IR Dome Cameras Overview To remove the mounting base release the latch Important Do not cut the DC jack or the female BNC connector as this will void t
3. he warranty Mounting base l Camera cover Dome cover oea es N Mounting screws egret Female BNC connector ER Cf Cnet OT eC OTS ne pe punt y noj Varifocal models only terminal block _ 9 i l y 1 Focus l m gt Dm il l DC jack vo Mae Zoom Before Starting 1 2 3 4 5 Please read this manual carefully and keep it for future reference Use the camera within given temperature and electrical limits Do not aim the LED light directly at the eyes when the LEDs are on Do not point the camera at the sun Heat could damage the camera even when not in use Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals 6 Do not open or disassemble the camera There are no user serviceable parts inside 7 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de gaussing which occurs automatically with many monitors when the monitor is turned on Installation f Run hidden cables from the video source and 12VDC power supply to the camera Connect to the DC jack and female BNC connectors Do not cut the DC jack or the female BNC connector as this will void the warranty If needed use the included SECO LARM DC plug with terminal block Test to make sure the voltage is c
4. ollateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2010 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com al PICSN4 Tel 800 662 0800 949 261 2999 E mail sales seco larm com MiEV 2xx1 NxBQ_1012 docx 4 SECO LARM U S A Inc
5. ooting Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen is blank e Clean the lens using a soft clean cloth Theo senmage isan e Check that the light source is adequate e Adjust the monitor s contrast knob The screen image has poor contrast e Change the position of the camera The screen image flickers e Change the position of the camera The screen image is distorted e Change the position of the camera The camera case is hot e Check that the correct power supply is in use IR LEDs do not turn on e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and Statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction such as smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no user serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class B digital device pursuant to
6. orrect Use only 12VDC Hold the camera against the wall ceiling or other mounting surface while watching the monitor to find the best mounting location Mark that location with a pencil Remove the dome from the camera by twisting it counterclockwise Remove the mounting base by releasing the latch indicated by white arrow on the inner rim of the camera If flush mounting remove the punch out in the base and run the wires through the center of the base 7 Mount the mounting base by using the three included mounting screws to secure it to the wall If the wall is made of drywall brick or similar material it may be necessary to also use the three included screw anchors 8 Secure the camera by lining it up with the base and turning the camera clockwise To line up make sure the gap in the mounting base is aligned with the wiring notch The camera will click when locked into place 9 Adjust camera angle as shown on page 2 Adjusting the Camera Angle 10 Test the video signal 11 Varifocal models only Adjust the zoom and focus by hand or with a small screwdriver to loosen the knob and then sliding the knob left or right IMPORTANT Do not use power tools Lens damage may result 12 Reattach the dome to the camera by giving the dome a slight twist The dome will click when locked into place 13 Do a final test of the video camera and monitor SECO LARM U S A Inc SECO LARM Indoor IR Dome Cameras Troublesh
Download Pdf Manuals
Related Search