SECO-LARM USA EV-122C-FVA3Q User's Manual
Contents
1. s female BNC connector to the video cable s male BNC connector While watching the monitor hold the camera against the wall or ceiling by hand where it is to be mounted then turn the camera until it is certain that this mounting location is correct Use a pencil to mark the location Disconnect the 12VDC power supply and video cable Drill a 22 4 56mm hole in the ceiling or wall where the camera is to be mounted Flange Ring bracket Power Ring bracket BNC inside the Connector ceiling wall magnetic fields or strong electrical signals 6 Do not open or disassemble the camera There are no user serviceable parts inside 7 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on 7 Twist the flange off the base and remove the camera ball 8 Place the ring bracket behind the hole Note Ring bracket is not necessary if mounting directly to wall 9 Push the base into the hole and secure to the ring bracket using the three supplied machine screws 10 Run the power supply and video cable through the wall or ceiling to the hole and through the bracket and base Connect to the camera s power and video connectors 11 Hold the ball in the base and secure with t2. ENFORCER F usH Mount Low Prorite UFO Camera MANUAL TROUBLE SHOOTING The screen is blank Check that the camera is powered up e Check that the monitor is powered up e Check that the video cable connecting the camera to the monitor is connected properly The screen image is dim e Clean the lens using a soft clean cloth e Check that the light source is adequate The screen image has poor Adjust the monitor s contrast knob contrast e Change the position of the camera The screen image flickers Change the position of the camera The screen image is distorted Change the position of the camera The camera case is hot e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction like smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide rea
3. f any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2008 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM file FLUSH MOUNT_IMU0407 PMD SECO LARWM U S A Inc Z PICSN4 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com MANUAL EV 122C FVA3Q V3 CCD Flush Mount Low Profile UFO Camera With Concealed Screws and Day Night Operation SC SECO LARM ENFORCER F usH Mount Low Prorite UFO Camera MANUAL eed Specifications Type Chip Resolution Pickup elements Sync Video output Lens F2 5 Minimum illumination Shutter control Gain control Gamma correction White balance S N ratio Power source Current consumption Ambient temperature Dimensions EV 122C FVA3Q NTSC Mini Flush Mount Low Profile UFO Camera 1 3 Sony Super HAD CCD 420 TV lines 510 H x 492 V effective pixels Internal 1 Vp p composite output 75 Ohms 3 7 mm B W 0 05 lux day nig
4. he flange Do not tighten securely 12 Apply power to the camera Watch the monitor and adjust the angle of the lens 13 Secure the camera by tightening the flange 14 Do a final test of the video camera and monitor
5. ht Auto Electronic Shutter AES 1 60 1 100 000 sec Auto 0 45 Auto gt 48dB 12 VDC 130mA 10mA 4 122 F 20 50 C 15 16 x 3 49 x 77 mm The EV 122C FVA3Q incorporates day night capability This means that the camera switches to B W mode at night Dimensions 21346 72mm a 2 4 56mm Parts List 1 x Flush Mount camera 1 x Flange 1 x Base 1 x Ring bracket 1h PN 3 x Mounting screws 3mm ee 1 x Manual ow 115 16 4 49mm 26mm 156 49mm 3 77mm ENFORCER FtusH Mount Low Prorite UFO Camera MANUAL Power cord included For easy connection of flush mount ball or other camera to power supply From DC Power adapter camera with terminal block Screws x 3 Flange Camera ball Base BEFORE STARTING l To BNC Please read this manual carefully and keep it for future reference Use the camera within given temperature and electrical limits Do not mount the camera where it is exposed to rain or other moisture or in humid or dusty places Do not point the camera at the sun Heat could damage the camera even when notin use Do not mount the camera in areas exposed to radiation strong INSTALLATION 1 Run a 12VDC power supply wire and a video cable with a male BNC connector to the wall or ceiling where the camera is to be mounted Temporarily connect the camera to the 12VDC power Supply Temporarily connect the camera
6. sonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages o
Download Pdf Manuals
Related Search