User Instruction Manual
Contents
1. The Heat Inside StormRider HEATED BODYWARMER USER INSTRUCTIONS WELCOME Your high performance StormRider Bodywarmer powered by FabRoc Heat Technology by EXO2 has been designed to provide you with warmth where and when you need it whatever the weather The core heating element FabRoc is a revolutionary material invented for use in the aerospace industry and is extremely efficient in generating heat from a low voltage source FabRoc panels are sewn into your StormRider to provide direct heat to your body in certain key areas transferring warmth throughout your body StormRider FabRoc panels are pre set to a maximum surface temperature of 122 F It is not possible to overheat FabRoc as it automatically uses less power as it reaches its operating temperature a unique property that ensures the material is intrinsically safe PRODUCT CONTENTS EXO2 StormRider bodywarmer Fused Power Unit Cable FabRoc panels sewn into the garment Portable battery pack Optional Accessory Battery charger amp power cord Optional Accessory StormRider Controller Optional Accessory CONNECTING TO THE MOTOR CYCLE The StormRider Bodywarmer is simple to set up and operate Every StormRider comes supplied with a standard power cable which has an inline 10 Amp fuse The fused line is to be connected to the positive terminal of the motorcycle battery The other line is to be connected to the battery s negative terminal To oper2. your StormRider bodywarmer repre AD hrough all layers HI PEFORMANCE AIRXSTREAM TEXTILE Insulation for heat towards body Bodywarmers using an optional battery pack will provide heat for up to 3 hours of continuous use on battery Level 5 SAFE OPERATIONS AND SAFETY FEATURES The FabRoc heating system has been designed for safe and reliable use It has been tested to comply with US safety regulations and has been marked with the CE seal of approval Safety devices are included to ensure the unit is rendered safe even under faulty conditions DO NOT replace or interfere with the electrical components in the StormRider Bodywarmer the battery or the charger unit DO NOT attempt to open the sealed battery unit Batteries should be discarded in accordance to local governmental regulations CLEANING INSTRUCTIONS Remove the batteries from your StormRider Bodywarmer Hand wash the garment in warm water using any commercial liquid soap product and rinse thoroughly It is inadvisable to use fabric conditioner biological powders or strong detergents DO NOT dry clean It is recommended to drip or line dry the vest jacket WARRANTY Every StormRider Bodywarmer has a one year warranty covering all electronic and mechanical failures In the unlikely event that any part should fail within the first year return it to us and we will repair or replace it free of charge Note The warranty does not cover intentional alterations acciden
3. ate the StormRider simply plug the bodywarmer power cord into the fused cable 2 5mm socket The bodywarmer will begin to heat up and will reach its maximum temperature in 10 15 minutes The self regulating properties of the jacket will prevent it from overheating STORMRIDER CONTROLLER OPTIONAL The StormRider Controller is easy to mount and operate The controller mount is designed to fit onto the existing clutch cable mount or similar The StormRider Controller connects to the battery via an inline 10A fused cable The fused line is connected to the motorcycle battery positive terminal and the other connected to the battery negative terminal The StormRider controller has an ON OFF switch and a digital readout The LED readout varies from 0 9 0 OFF No Power to Jacket 1 50 Power and 9 100 Power When first switched ON the controller will default to the top level 9 100 power for fast warm up The selector button on the front will cycle the power level to the desired setting USING THE 14 8 VOLT LITHIUM IN BATTERY OPTIONAL 1 Remove the connecting cable from the pocket 2 Insert the small 1 3mm DC plug into the battery socket 3 Use the ON UP and OFF DOWN buttons on top of the battery to dial in your preferred heat level 1 5 5 being the highest 4 When using the optional portable rechargeable battery the lower back portion of the StormRider will heat The power cable for the battery is the small 1 3mm
4. plug which plugs into the 1 3mm socket in the pocket to complete the full four panel circuit when the Bodywarmer is being powered by a direct connection to your powersport unit battery CHARGING THE BATTERY 1 Remove the battery pack from the StormRider pocket 2 Connect the charger plug to the battery socket 3 Plug the charger into the wall outlet 4 The battery s charge level indicator will tell you how much charge life is remaining Levels 0 9 with 9 being fully charged and O being fully depleted This indicator will also continuously exhibit the charge level while plugged into the charger 5 Depleted battery packs will take approximately 3 hours to fully recharge When the battery is completely charged the system allows no further current to enter the battery 6 The battery will be fully charged when the battery displays 9 on the LED and the light on the charger turns green The charger unit supplied has been chosen specifically for the EXO2 battery packs No other charger should be used The use of any other charger unit is dangerous may cause injury and will void the warranty Wind Deflected GETTING THE BEST RESULTS Although the battery has been charged and checked we recommend that you charge it for at least 3 hours prior to first use The closer the owen FabRoc panels are to your skin the more heat you will feel For rue maximum benefit wear only a fine pullover t shirt or blouse underneath
5. tal damage or improper cleaning TROUBLESHOOTING What happens if my StormRider Bodywarmer is torn 1 DO NOT attempt to replace or interfere with the electrical components in the StormRider Bodywarmer 2 Return the garment to EXO2 for repair What happens if my StormRider Bodywarmer does not get warm If powered by a 12v volt power unit battery ensure that the 1 3mm rechargeable battery cable is plugged into the 1 3mm socket also in the pocket to complete the four panel circuit If using a portable rechargeable battery confirm that the battery is properly charged per the previously mentioned instructions If the red light on the charger comes on and stays on and or the LED on the battery reads 0 or 1 the battery needs to be recharged If the battery is charged confirm the StormRider Bodywarmer cable is properly fitted into the battery and the battery indicates the selected heat level If it still does not heat call EXO2 Customer Service at 877 396 2432 NEVER LEAVE BATTERIES THAT ARE CHARGING UNATTENDED KEEP BATTERIES AWAY FROM WATER Should you have any questions about your heated products please contact 2 O 3 Customer Service The Heat Inside EXO2 The Heat Inside NA LLC 300 Lester Mill Road Suite 220 Locust Grove GA 30248 TEL 1 877 EXO2 HEAT WEB www exo2 com E mail info exo2 com
Download Pdf Manuals
Related Search