SECO-LARM USA 84-IR User's Manual
Contents
1. 2 SECO LARM U S A Inc ENFORCER 84 IR LED Bullet Cameras Dimensions 4 5 118mm ENFORCER infrared Day Night Le lt lt 10 260mm ______ a 1013 16 275M _____ _ gt 451 416mm Overview Sunshield Sunshield ee screw Coa Mounting base mq Surface mount PA knock out Remove with a pair of pliers DC Plug with terminal block Mounting arm Female BNC connector adjustment screw ENFORCER infrared Day Night L mp Camera angle Mounting Adjustment adjustment screw arm screw DC jack Zoom Focus Adjustment nut Before Starting 1 Please read this manual carefully and keep it for 5 Do not mount the camera in areas exposed to future reference radiation strong magnetic fields or strong electrical 2 Use the camera within given temperature and signals electrical limits 6 Do not open or disassemble the camera There are 3 Do not aim the LED light directly at the eyes when the no field serviceable parts inside LEDs are on 7 Do not drop the camera or subject it to strong 4 Do not point the camera at the sun Heat could damage vibrations the camera even when not in use Installation 1 Runa 12VDC power supply wire and a video cable 4 Disconnect the 12VDC power supply and video cable with a male BNC connector through the wall to where 5 Mount the bracket2. 210ft 64m Operating voltage 12VDC Current LEDs OFF 130mA 130mA draw LEDs ON 660mA 660mA Operating temperature 14 122 F 10 50 C Dimensions 1013 16 x 45 16 x 45 8 275 x 116 x 118 mm Weight 2 lb 7 0z 2kg Parts List 1xIRcamera 1xSunshield 1xDCplugwith 1xManual 1xHexwrench 4x Mounting screws terminal block Optional EV 11LS Single Gang Mounting Plate Sold separately ENFORCER 84 IR LED Bullet Cameras can ol mount to an optional single gang mounting plate 1 Run the camera s wires through the plate EV 11LS 2 Use the 4 included mounting screws to mount the EV 11LS single gang plate to the wall 3 Remove the base from the camera by twisting 4 Twist the camera into the plate until it is tight 5 Screw the mounting arm into the plate until it is tight 6 7 Tighten the adjustment nut on the camera Tighten the secure screw on the plate Optional EV 11LR Round Junction Box Sold separately ENFORCER 84 IR LED Bullet Cameras can mount to an optional round junction box EV 11LR 1 Use the mounting template included with the EV 11LR to mark and drill into the wall if necessary 2 Use 4 mounting screws included with the EV 11LR to mount the junction box to the wall 3 Mount the camera through the foam pad included with the EV 11LR to the junction box 4 Wire can either be run through the large opening in the center of the EV 11LR or through the conduit fittings on the side
3. radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication H
4. to the wall using the four included the camera is to be mounted mounting screws 2 Temporarily connect the camera to the 12VDC power 6 If mounting to the EV 11LR or EV 11LS see instructions supply Do not cut the DC jack or female BNC plug on page 2 as warranty will be voided If needed use the 7 Reconnect the 12VDC power supply and video cable included SECO LARM DC plug with Tum the monitor on and make sure the camera is terminal block sending the proper video signal 3 Temporarily connect the camera s female BNC jack to 8 To adjust the camera angle loosen and tighten the the video cable s male BNC plug While watching the adjustment nut or loosen and tighten either of the two monitor hold the camera bracket by hand against the screws on the mounting arm Adjust until the desired wall where it is to be mounted then twist the camera scene is displayed until it is certain that this mounting location is correct 9 Adjust the zoom and focus using the included hex Use a pencil to mark the location of the four screw wrench holes in the bracket 10 Do a final test of the video camera and monitor SECO LARM U S A Inc 3 ENFORCER 84 IR LED Bullet Cameras Troubleshooting Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen is blank e Clean t
5. ENFORCER EV 1826 NKGQ NTSC EV 1826 PKGQ PAL 84 IR LED Bullet Cameras Manual ENFORCER jnirared Day Night e 1 3 Sony Super HAD II CCD A e 2 8 12mm Varifocal lens Zeta Series Model No Weatherproof IP66 OSD Controller EV 18C e OSD functions accessible with optional OSD controller EV 18C e Optimized to produce clear images at night e Cables concealed in bracket e 12VDC operation e Optional single gang mounting plate Use to access the OSD On Screen Display functions for compatible cameras without having to be near the camera and round junction box available Not included For more information please see the EV 18C manual SC SECO LARM FE CEG Note Model numbers that end with Q or that have a round green Q sticker signify ROHS compliant products ENFORCER 84 IR LED Bullet Cameras Specifications Model EV 1826 NKGQ EV 1826 PKGQ Type IR LED Bullet Camera ccD 1 3 Sony Super HAD II of infrared LEDs 84 Lens 2 8 12mm Resolution 600 TV lines 600 TV Lines Pickup elements 768x494 pixels 752x582 pixels Sync Internal Video output 1 0Vp p Composite video 750 Video output format NTSC PAL Minimum LEDs OFF 0 1 Lux illumination LEDs ON 0 Lux Gamma correction 0 45 SIN ratio gt 45dB Shutter control Auto Electric Shutter AES Gain control Auto IP rating IP66 LED range Up to
6. he lens using a soft clean dry and lint free cloth he sc een Image is dim e Check that the light source is adequate e Adjust the monitor s contrast knob he sersen mage fies pod vonirast e Change the position of the camera The screen image flickers e Change the position of the camera The screen image is distorted e Change the position of the camera The camera case is hot e Check that the correct power supply is in use IR LEDs do not turn on e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction such as smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate
7. owever the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2012 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com E ca Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com miEv 1826 xKGQ_1206 d0cx SECO LARM U S A Inc aN
Download Pdf Manuals
Related Search