Sebo Airbelt D User's Manual
Contents
1. 8 Starting the machine with non power head attached 8 Additional Instructions for starting the machine with a power head attached 8 SUC HOM COMOL 9 TELESCOPIC 9 Using the Telescopic TUDE Hose amp Attachments 9 Bagi Fulluor Clog Indicator amp Auto Shut ofi 9 PEEL SCUIMNG UNC a 5 10 LED IP OWED MAIC ALON ssc S 10 Viele 10 Use and Maintenance of Brushes and Heads csccccccccccccccccsccccscscccsccccsesccsecces 10 10 The Optional Premium Parquet aa 10 8 NOZZE ce onnsueacustier usnustusiceucscsanacdaksnasensaccanaacunsnocdessiss 10 The Optional Turbo 1022 67 10 VACUUM Maintenance 11 Changin Meteo aC 11 11 Changing the Motor FIET 12 Changing the Hospital g2. Cleaning Dimensions The ET 1 power head 15 12 inches wide with a cleaning with of 10 4 inches and the ET 2 is 14 inches wide with a 13 inch cleaning width Brushless Cleaning Capability The ET 1 or ET 2 power heads can provide gentle brushless cleaning of delicate rugs or hard floors because the brush roller may be switched off but suc tion will continue Brush Obstruction Light amp Auto Shut Off If an obstruction becomes jammed in the brush roller a warning light will quickly flash the brush roller will immediately stop spinning and the vacuum will shut off The user should turn the power switch off unplug the machine and immediately remove the obstruction If the user restarts the machine without removing the obstruction the power head will again shut off and the amber light will turn on This prevents the belt from breaking and protects the motor from damage Incorrect Height Setting or Brush Deterioration Light To ensure optimum cleaning at all times a warning light will illuminate to indicate when the brush height is set too high for effective cleaning or when the brush roller should be replaced due to excessive wear Four level Manual Brush Height Adjustment The brush height can be adjusted up or down for optimum cleaning Both Carpet and Hard Floor Cleaning With a power brush to clean carpets and a parquet nozzle to clean hard floors the AIRBELT D4 provides all the flexibility needed to car
3. and the ET 1 power head motor is 175 watts for a total of 1 425 watts The ET 2 power head is 200 watts for a total of 1450 watts 320 Degree Rotating Hose A brilliantly designed hose to canister connection allows 320 degree rotation of the suction hose pro 2 viding easier user movement and machine maneuverability Shock Absorber Provides Furniture and Wall Protection The patented AIRBELT bumper that surrounds the D4 canister acts as a protective barrier The soft foam bumper with its durable covering protects furniture walls and the vacuum itself from damage during use Personalized Vacuums AIRBELT canister vacuums can be personalized with a replacement AIRBELT bumper cover avail able in eight patterns and colors Rubber Coated Wheels and High Quality Castors The quality of the wheels and cas tors on SEBO canisters prevent damage to floors and rotate 360 for easy maneuverability 2 Large Operating Range A 40 foot cord with 90 foot cleaning radius saves time because it minimizes the number of electrical outlets needed during use Three Full Size On board Tools and Parquet Brush The vacuum comes standard with a crevice tool dusting brush and upholstery nozzle which are conveniently stored on the vacuum Also included with the D4 is the Parquet Brush for gently cleaning hard floors It is lightweight with soft bristles so it glides gently over floors Many optional accessories are also ava
4. HEADS Always unplug vacuum from outlet before dismantling any part of machine To remove a brush or power head switch off the power and unplug the vacuum Then press the tool release button 9 and pull the tube out 287 NOTE D4 users with 1 2 DISCO power heads please refer to your power head user s Figure 18 manual for more detailed instructions for operating and maintaining your power head Parquet Brush standard Figure 18 The D4 comes with a parquet brush 28 that was designed specifically for vacuuming hard floors It is lightweight with soft bristles so it glides gently over floors and provides easy maneuverability Fibers and hair can be pulled out of the bristles manually or vacuum the bristles with the telescop ic tube Premium Parquet Nozzle optional Figure 19 The Premium Parquet nozzle 32 is especially designed for use on hard surfaces The brush should be cleaned regularly Remove the parquet nozzle from the telescopic tube to clean Fibers and hair can be pulled out of the bristles manually or vacuum the bristles with the telescopic tube The brush strips are removable for cleaning and replacement Kombi Nozzle optional Figure 20 The Kombi nozzle 10 is adjustable for carpet or hard floors To set for carpet slide the up arrow button 46 to the right until it clicks into place The hard floor dusting brush will raise up allowing the head to move over the carpet To set for hard
5. and on using the power control button 2 figure 2 the handle To turn the power head off using the power control button on the handle push the minus button until the suction stops The green light 44 on the power head will then shut off The blue light 8 on the canister will remain illuminat ed until the vacuum is powered off using the On Off button on the canister 6 Always turn the power off on the canister AND the power head when changing heads or unplugging the vacuum Press the minus on the power control button 2 on the handle grip until the suction stops press the On Off button 6 on the base of the canister gently with your foot or hand then unplug the canister to completely shut down the power when changing heads or storing the vacuum Continue to page 9 WARNING The quality condition coating texture age and manufacturing technique of all floor surfaces vary Therefore vacuums with rotating brushes Including your SEBO may damage some floor coverings or surfaces Some types of high gloss hardwood floors cushion vinyl berber carpets long shag and delicate or hand woven carpets are par ticularly vulnerable to damage by rotating brushes When possible consult the materials sup plied by your flooring manufacturer for information on proper upkeep and cleaning To ensure that your new SEBO vacuum cleaner is compatible with your floor please test the vacuum cleaner on each type of flooring surface in
6. cooling provided by the airflow Once the motor reaches a certain temperature it will shut off to protect itself from damage The user should turn the switch off unplug the machine and immediately insert a new bag or remove the clog to remove a clog refer to the Clog Removal section on page 13 After approximately 30 minutes the motor will have cooled and the vacuum can be restarted High quality Telescopic Tube and Hose On the AIRBELT D4 the power cord is built inside the telescopic tube and suction hose This eliminates unsightly external wires and enables unobstructed and convenient handle height adjustment Variable Power Control on Handle The vac uum s suction power can be adjusted from 0 to 1 250 watts by a slider switch convenient ly located on the handle Comfortable Ergonomic Handle The AIRBELT handles are ergonomically designed and positioned to reduce wrist and arm fatigue For extra comfort an additional swivel is built into the handle to hose connection Quick release Connections The AIRBELT D4 models allow for quick and convenient connection of telescopic tubes power brush heads accessory cleaning heads and on board tools LED Suction power Indicator The indicator tells the user with a glance how much suc tion power they are using The light rotates slower or faster depending on the suction setting Powerful Vacuum Motors Provide Excellent Cleaning The canister suction motor is 1250 watts
7. floors slide the down arrow button 47 to the left until it clicks into place The brush will lower to gently sweep your floors The slider in Figure 20 is set in the position for hard floors Remove the Kombi nozzle from the telescopic tube to clean Fibers and hair can be pulled out of the bristles manually or vacuum the bristles with the telescop ic tube The brush strip is removable for cleaning and replacement f J Turbo Nozzle optional Figure 21 The Turbo nozzle 33 has an air driven rotating brush for gentle brushing of carpets The Turbo nozzle can be adjusted for high and low pile carpet To adjust the head for high pile carpet push the slider button 48 to the right For low pile carpet push the slider button 48 to the left The slider in Figure 21 is set in the low pile position Remove the Turbo nozzle from the telescopic tube to clean Remove fibers and hair from the brush manually 10 VACUUM MAINTENANCE Always unplug vacuum from outlet before dismantling any part of machine Changing the Filter Bag Figures 22 23 24 25 amp 26 To change the filter bag 40 switch off the power and unplug the vacuum Lift the cover release catch 15 figure 22 and raise the filter bag cover 18 Seal the filter bag with the sealing cap 49 Lift the filter bag out of the holder by tilting the green collar 50 up and pulling it out of the holder as shown in figure 23 Insert the green collar of a new filter bag
8. in the rear of the machine Make sure they snap into place firmly The dusting brush 22 has a rotating head If it is not fitting into its storage space rotate the head to another position Bag Full or Clog Indicator amp Auto Shut Off Figure 12 When the BAG FULL OR CLOG indicator located on top of the canister 12 turns orange airflow is reduced due to a full bag a clog In the airflow pathway or an excessively dirty fil ter Turn the power off unplug the machine and immediately insert new bag see 11 or remove the clog see page 13 If the user ignores the orange warning indicator and the motor reaches a certain tempera ture it will shut off to protect itself from damage The user should turn the power off unplug the machine and immediately insert a new bag or remove the clog After approximately 30 minutes the motor will have cooled and the vacuum can be restarted If the airflow ts still restricted the BAG FULL OR CLOG indicator will turn orange again and the machine will shut off This feature prevents damage to the motor due to overheating Vacuuming fine dust may require an earlier filter bag change even though the filter bag is not full Fluff may overfill the bag without the light coming on The bag full indicator works more efficiently at full power Check the bag full status reg ulary at full suction power Figure 12 Retracting the Cord Figure 13 To retract the cord switch the vac
9. into the neck of the head or brush 10 until it locks into place or line up the square hole in the telescopic tube with the notches in the front of the neck and snap firmly into place To release a head or brush from the telescopic tube 5 push the head release button 9 and pull the head or brush tool off the end of the telescopic tool The release button 9 is in the same position on all of the heads brushes and power heads NOTE To attach a SEBO power head ET 1 ET 2 or DISCO to your D4 canister please refer to your power head owner s manual for instructions Attaching incorrectly could cause damage OPERATING INSTRUCTIONS Starting the machine with a non power head attached Figures 1 2 amp 3 Before turning on your canister make sure that you have a firm hold on the handle grip to keep the machine from moving forward 1 With the canister On Off button 6 in the OFF position and the power control button 2 on the han dle grip 1 in the OFF position grasp the plug and pull the power cord 21 out from the power cable recess figure 3 The power cord 21 should be unwound from the cable reel at least two thirds of its length Note do not over extend the cord 2 Plug the polarized power cord into a 120 volt wall outlet located near the floor 3 Press the canister On Off button on the base of the canister 6 gently with your foot hand The blue light around the button 8 will blink r
10. more information on the Premium Parquet Kombi and TT C Turbo Nozzles TT C Turbo Nozzle Premium Parquet Nozzle SEBO FRESH Filter Bags Wall amp Floor Brush Filters SEBO filter bags can be purchased in boxes of eight and filters are sold as a set SEBO bags filters and accessories are rea sonably priced and widely available To create a fresh scent while vacuuming SEBO FRESH is available To use deposit a scented stick in the filter bag Flat Upholstery Nozzle Hand held Turbo Brush Radiator Brush Extension Tube Nine foot Extension Hose IDENTIFICATION OF PARTS 1 Handle grip 14 Hose neck 2 Power control slider 15 Cover release catch 3 Handle release button 16 Carrying handle 4 Slide Button 17 AIRBELT shock absorber 5 Telescopic tube 18 Filter bag cover 6 On Off button 19 Suction opening 7 Cable rewind button 20 Parking groove 8 LED suction power indicator 21 Power cable 9 Tool release button 22 Dusting brush 10 Kombi nozzle optional 23 AIRBELT clip 11 Hose 24 Upholstery nozzle 12 Bag full or clog indicator 25 Crevice nozzle 13 Hose neck release tabs 26 Carrying Parking groove 27 Micro filter holder Standard Attachments amp Heads 22 Dusting brush 25 Crevice nozzle 24 Upholstery nozzle 28 Parquet brush Standard amp Optional Power Heads 29 ET 1 Power head Standard on Premium D4 Black and Premium D4 White Optional for D4 Red Part 9299AM 30 ET 2 Powe
11. the bag full or clog warning indicator 12 remains orange after the filter bag has been changed and the filters are in good condition there is likely a clog in the sys tem Clogs in the Head or Brush Figure 34 Clogs in the swivel neck 63 of a head or brush can be cleared by first pressing the tool release button 9 and removing the brush or head Check inside the swivel neck chan nel 64 and clean out pathway Clogs in the Telescopic Tube Figure 35 Remove head from telescopic tube 5 by pushing the tool release button 9 and pulling the tube out Remove the handle grip 1 from the top of the telescopic tube by pushing the handle grip release button 3 A stiff wire or stick can be used to push the clog out of the tube Clogs in the Hose Figures 35 36 37 amp 38 Check for suction at the end of the hose by removing the handle grip 1 from the tele scopic tube 5 and putting your hand over the handle grip suction opening 65 Turn the power on and slide the suction up to full power If you feel reduced suction the blockage Is in the hose If the blockage is in the hose there are two ways to clear it 1 With the telescopic tube disconnected from the handle grip 1 hold the hose upright with one hand blocking the handle grip suction opening 65 and switch on the machine with full suction power If necessary quickly lift your hand on and off the end of the hose If that does not clear the clog you may al
12. 800 270 4807 Website www sebocanada ca To contact SEBO in the United States of America SEBO America LLC Telephone 800 334 6614 915 5 Ye Tp Fax 303 792 9196 amp MEAR WARRANT lt FEAR Website www sebo us x Y MADE IN GERMANY 16 Copyright SEBO America LLC All rights reserved
13. 9 x 13 4 b 49 8160 Internal cable 50 8093 Hose neck wiring 51 8038ER4 Power display 16 17 amp 52 52 8108ER PCB w lights 53 6369GS Mains cable 90640AM PREMIUM D4 Black onyx Machine Exceptions 1 8001SWER Bottom casing 2 20 6047AM 02 AIRBELT cover silver 26 8003SWER Top casing 23 25 36 8005SWER cover 90630AM D4 Red Machine Exceptions 1 8001DRER Bottom casing 2 26 8003DRER Top casing 23 25 28 8010D4ER Attachment holder cpl 36 8005DRER Bag cover ET 1 Power Head Standard for D4 Premium 9951AM Black Onyx 9258AM White Optional for D4 Red 2 Power Head 9299AM Red optional for D4 Red 9250AM Red SEBO VACUUM CLEANER WARRANTY Your authorized SEBO dealer or SEBO will provide the original product purchaser with replacement of Non Wear Parts which fail due to a material or workman ship defect for a period of five 5 years from the orig inal date of purchase of new product SEBO will provide a five 5 year warranty on suction motors and brush drive motors Your authorized SEBO dealer or SEBO will repair or will cover labor charges associated with repair a defective SEBO vacuum cleaner at no cost to the original pur chaser within five 5 years of original purchase of new product in the United States and within one 1 year of original purchase of new product in Canada SEBO or an authorized SEBO dealer must complete all warranty repairs To locate
14. A Lu 4 an Lu Wn MADE IN GERMANY OWNER 5 MANUAL SEBO KOWSA DO0000G Cee Or Sa SQ gt DP OGG SOO OOOOOOOOOOOOOOOOOOOSES CS Sa DOOD DOD a 2 FS steisisis sie Se ee nnnm 7 y Ra lt y yy 9 2 lt For Household Use Only TABLE OF CONTENTS Technical cee 2 important Safely Special AIRBELT D Product Features 4 EIPOwer Meads POOUCE 5 Optional DISCO Floor Polisher Product Features 6 Optional Attachments Accessories Bags and Filters 6 identification OF Parts orrea OE 7 E 7 7 7 INSUFUCUONS
15. a small inconspicuous area to determine if any damage occurs If damage occurs stop using the vacuum cleaner immediately 8 Figure 6 Suction Control Figure 7 The suction power will automatically increase from standby to maximum power after the machine is switched on You can override this process by pressing the plus or minus on the power control button 2 conveniently located on the handle grip 1 Press the plus on the button for maximum suction or press the minus to reduce suction for vacuuming curtains or delicate fabrics You may adjust the suction control with the power control button 2 as you vacuum different surfaces or when using the accessory tools For optimal cleaning and brushing operate the machine at the maximum suction power setting and push the head Slowly over the carpet Adjusting the Telescopic Tube Figure 8 Adjust the telescopic tube 5 to the correct height by pushing the slide button 4 and gently pulling the tube out to lengthen or pushing it in to shorten Release the slide button 4 to lock the tube to the adjusted height The handle can be lowered to a horizontal position useful for vacuuming under beds Using the Telescopic Tube Hose amp Attachments Figures 9 10 amp 11 The telescopic tube 5 is useful for vacuuming corners and hard to reach areas You may use the telescopic tube without a brush power head or attachment To remove a brush or power head switch off the canister On Of
16. an authorized SEBO dealer in your area or to register a warranty claim in the United States of The Wear Parts excluded from warranty coverage include filter bags motor filters micro filters the cable external the attachment hose the brush rollers the front bottom plate the rear bottom plate the crevice nozzle the upholstery nozzle the dusting brush the parquet brush and all of the optional attach ments See Identification of Parts on page 7 of this manual This warranty applies only while your SEBO Vacuum Cleaner is physically located within the United States of America and its territories or Canada The purchase receipt showing the date price and item of purchase Is the initial document of proof of purchase and determines the validity of warranty To be certain that your warranty claim can be processed as quickly and efficiently as possible please retain your original purchase receipt and mail in the warranty card provided with your new SEBO vacuum cleaner America please visit our website at www sebo us This warranty gives you specific legal rights You may also have other legal rights which vary from state province to state province To locate an authorized SEBO dealer in your area or to register a warranty claim in Canada please call Floor Care Equipment Ltd at 800 661 8687 SEBO America will not process nor will it accept responsibility for warranty claims for machines pur chased fr
17. down into the filter bag holder vertically as shown figure 25 Line up the tabs 52 figure 24 with the slots on the green collar 51 figure 26 and gently push the collar down flat until the center U shaped clip 53 figure 24 moves all the way forward Close the cover making sure it snaps shut com pletely Do not re use the filter bags The bag full or clog indicator works correctly only at full power Check the status of the filter bag regularly at full power Note The nature of the contents of the filter bag will affect the point at which it needs changing Fine dust may require an earlier change even though the bag 1 not full Fluff or hair allows air to pass through easily so the filter bag may over fill before the bag full indicator turns orange 49 51 51 40 Filter Bags Filterbox D Part 8120AM Figure 24 Figure 25 Figure 26 Changing the AIRBELT Figure 27 If damage occurs to the AIRBELT cover it will need be replaced To remove the AIRBELT 7 pry off the clip 23 by inserting the tip of a slot head screw driver under the bottom side of the clip Push outward carefully on the screw driver until the clip pops off Grasp the end of the AIRBELT cover 7 and pull the AIRBELT cover will peel off The foam bumper 54 remains the vacuum To replace the AIRBELT insert the side ribs of the AIRBELT into the grooves 55 Start at the back insert the rib of the AIRBELT cove
18. e for a vari ety of floor surfaces The D4 vacuum can morph into a hard floor polisher by adding a SEBO DISCO head SEBO DISCO FLOOR POLISHER OPTIONAL FOR THE AIRBELT D4 Polish your hard floor with a SEBO DISCO Ultra High Speed floor polisher The SEBO DISCO 13 wide 11 polishing width never been easier to make hard floors shine The SEBO DISCO floor pol isher can both vacuum and polish for a super gloss finish It can be attached to the FELIX uprights or to the AIRBELT canisters Its suction removes fine dust dust from fully dried floor polishing product during polishing and the 2 000 rpm disc speed will create a high gloss shine for a fantastic hard floor finish DISCO FEATURES SEBO floor pad Brilliance at work The SEBO floor pad has been developed to achieve the optimum polished finish on all Suitable surfaces In addition the floor pad 5 easy to change and maintain Automatic height adjustment Every hard floor is different The SEBO DISCO adjusts the floor pad automatically to different floor N conditions The torque of the rotating floor pad is constantly measured for best adjust ment A vacuum Seal around the base of the polisher ensures that even the finest dust gets drawn into the intake flow Automatic shut off Intelligent safety The SEBO DISCO is a smart machine The green LED light indicates that the SEBO DISCO is operational and everything is ok The red LED light comes on if the mach
19. f button 6 and unplug the vacuum Then press the tool release button 9 and pull the tube out The crevice nozzle 25 dusting brush 22 upholstery nozzle 24 and parquet brush 28 may be inserted onto the end of the tube It is not neces sary to turn off the vacuum while switching the standard attachments the crevice nozzle upholstery nozzle or dusting brush After use switch off the power unplug the vacuum and remove attachment Re insert the telescopic tube into the power head or brush turning the tube if needed until you hear it click into place NOTE D4 users with power heads please refer to your power head user s manual for more detailed instructions for connecting your power head To use the hose and handle grip without the telescopic tube switch off the canister On Off but ton 6 and unplug the vacuum Push the handle grip release button 3 and pull the HANDLE GRIP out of the end of the telescopic tube Do not try to separate the hose from the handle Insert the crevice nozzle 25 dusting brush 22 or upholstery nozzle 24 onto the end of the handle It is not necessary to turn off the vacuum while switching the standard attachments the crevice nozzle upholstery nozzle or dusting brush After use switch off the power unplug the vac uum and remove the attachment Re insert the handle into the telescopic tube making sure it is seated correctly and snap It into place The three standard attachment tools are stored
20. he power and unplug the vacuum Press the release button 58 locat ed on the filter holder 27 as shown in figure 30 While holding the button in rotate the holder counter clockwise and pull it out Remove the filter 41 from the filter holder 27 by pulling the rubber strip 59 figure 31 away from the notches 60 that hold it onto the base of the filter holder then pulling the filter off Fit the new filter down over the holder lining up the notches 60 the holder with the holes 61 in the red rubber strip The two tabs located on the indented portion of the red filter rim hook onto the holder rim see position 62 figure 32 Tuck the peak of the filter down as shown in fig ure 31 Insert the assembly back into the machine and turn the holder cover clockwise figure 33 It is not necessary to press the release button to close the filter holder Hospital grade Micro Filter D Filter Set Motor Filter and Hospital grade Micro Filter Part 8191AM Note Never operate the vacuum with incorrectly attached filters or without filters bag AIRBELT or filter bag housing cover 18 Do not re use filter bags Do not wash and re use filters 12 Figure 33 CLOG REMOVAL Always switch off power and unplug vacuum from outlet before removing any clogs NOTE D4 users with ET 1 ET 2 or DISCO power heads please refer to your power head user s manual for more detailed instructions for removing clogs in your power head If
21. ight and left indicating that the power is on Your SEBO AIRBELT D4 has a soft start system for longer component life This may delay starting slightly Always turn the power off on the canister AND the power head when changing heads or unplugging the vacuum Press the minus on the power control button 2 the handle grip until the suction stops press the On Off button 6 on the base of the canister gently with your foot or hand then unplug the canister to completely shut down the power when changing heads or storing the vacuum Continue to page 9 Additional instructions for starting the machine with a power head attached Figures 1 2 3 4 5 amp 6 Please refer to your ET or DISCO power head owner s manual for more information Before turning on your canister make sure that the vacuum handle is in its upright locked position figure 4 Follow steps 1 3 above When the power head is switched on with the handle in the upright locked position figure 4 the brush roller on the power head will not spin To release the power head from the upright locked position press down on the foot pedal 43 figure 5 and lower the handle into the normal operating position Push the brush roller button on the top of the power head 44 figure 6 to engage the brush roller The green light on the power head will illu minate When the canister On Off button 6 figure 1 is in the ON position you may turn the power head off
22. ilable SEBO AIRBELT D4 PRODUCT FEATURES Liberation from Bagless SEBO Bags are Hygienic The three layer filter bag is an integral part of SEBO s filtration system because it effectively contains nearly all dirt captured by the vacuum SEBO bags can be sealed when full so no dust can escape into the air during disposal In contrast a lot of dust becomes airborne when emptying the dirt containers of bagless vacuums and their micro filters quickly clog and must be replaced often or a loss of suction will occur Bagless vacuum micro filters are expensive usu ally costing much more than SEBO s filter bags A Huge 1 5 Filter Bag The large pg gt capacity filter bag is convenient and eco AS 2 nomical because fewer bag changes needed Micro Filters are Inexpensive and Easy to Change Unlike most other vacuums SEBO s replacement micro fil ters are reasonably priced and can be easily changed in seconds without any tools And the micro filters last a long time before replace ments are necessary because nearly all dust particles and debris are first captured by the three layer filter bags Anti allergy Hospital grade S class Filtra tion An excellent choice for users with allergies or asthma Certified by leading Allergy foundations in Europe the AIRBELT D4 vacuums provide the user with S Class fil tration of 99 9 of particles to 0 3 microns This is accomplished by the SEBO three step filtratio
23. ine has shut down for safety reasons for example if there is a blockage A Soft Bumper Care everywhere Every room has obstructions That is why the SEBO DISCO has a soft bumper Furniture and walls are protected against scratches and marking A highly maneuverable swivel neck and three castor design glides over the floor Three high quality castors support the SEBO DISCO At the rear are two 360 flexible cas tors which are fixed on a solid steel shaft A castor in the middle helps the SEBO DISCO to stay on the right track Working with the flex neck they give the SEBO DISCO its Supreme maneuverability The castors are rubberized to prevent skidding and to pro tect the floor Immediate retention of polishing dust by the suction unit Reinforced drive disc that provides optimal floor contact and a speed of 2 000 rpm SEBO DISCO Black Part 9433AM SEBO DISCO White Part 9430AM OPTIONAL ATTACHMENTS ACCESSORIES BAGS amp FILTERS In addition to the standard on board tools a variety of optional attachments are available The nine foot extension hose extends suction hoses and the 20 inch extension tube are very popular because they create useful tools for cleaning stairs and out of reach areas These two items are sold separately or as part of multiple item attachment kits Another popular attach ment is the hand held turbo brush for removing pet hair from upholstery and stairs See page 10 for
24. it fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Connect only to the outlet type specified on the serial number plate underneath the machine SAVE THESE INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury Do not leave vacuum while plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not use near small children or pets Do not allow to be used as a toy Use of this product by children should always be supervised by an adult Use only as described in this manual Use only manufacturer recommended attachments Do not use with a damaged cord or plug If vacuum Is not working as it should has been dropped damaged left outdoors or dropped into water take it a SEBO service center Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run vacuum over cord Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not plug in if switch is in the ON position Do not use outlets above counters to plug in vacuum damage to items in the surrounding area could occur Always carry the vacuum over steps and sills Do not handle plug or vacuum handle with wet hands Do not put any object into vacu
25. l button 4 Set power control button to switch is set to off position position See page 9 1 Bag full 1 Replace filter bag See page 11 2 Clog in hose telescopic tube 2 See Clog Removal on page 13 brush or head or entrance to Users with clog in power head filter bag attachment refer to clog removal in the ET 1 ET 2 or DISCO owner s manual 3 Hospital grade micro filter dirty 3 Replace hospital grade micro filter See page 12 4 Motor filter dirty 4 Replace motor filter See page 12 1 Hose handle assembly not 1 Re insert hose handle assembly correctly inserted making sure that Is lined up properly and 15 snapped into place See page 7 2 The power control button 2 Set power control button to switch is set to off position position See page 9 3 Filter bag cover not closed 3 See below 1 Filter bag cover not fully closed 1 Re insert bag Lock the cover down firmly See page 11 2 Bag not inserted properly 2 Re insert bag Lock the cover down firmly See page 11 3 Motor filter not properly 3 Remove the filter bag cover 18 and inserted make sure the motor filter is seat ed firmly in place all the way around the rim See page 12 AIRBELT D4 SCHEMATIC AND PARTS LIST Canister with Handle Hose 90640AM Premium 04 Black Onyx 90630AM D4 Red 90641AM Premium D4 White 90641AM Premium D4 White Machine Pos Part Desc
26. n system First the three layer full size filter bag collects the vast majority of the debris Then the remainder of the particles are collected by the motor filter b Finally the hospital grade micro filter cleans the exhaust air that the vacuum emits The AIRBELT 9 disperses the filtered exhaust air around the canister which provides quiet gentle air flow 5 unwaver ing attention to the complete sealing of the machine ensures no dirt escapes around the microfilters anti allergy hospital grade S class filtration Effective Pet Hair Removal All SEBO vacuums easily remove pet hair Remarkably Quiet Operation Intelligent design and high quality motors combine to provide amazingly quiet vacu ums ET Power Heads Designed for All Floor Surfaces Deep clean your carpet with a SEBO ET power head SEBO power heads are virtual ly maintenance free and their electronic overload protection feature extends belt life by automatically shutting off power if a brush roller jams These power heads deliver cleaning flexibility because their brush action aggressively cleans carpeting and the brush may be switched off to clean hard floors and delicate rugs The steering ability of the swivel necks help to easily clean around obstacles and their L shaped heads provide maneuverability around fur niture and under cabinets They also have brush height and brush wear warning lights
27. om dealers located in Canada Floor Care Equipment Ltd will not process nor will it accept responsibility for warranty claims for machines pur chased from dealers located in the United States The warranties provided for above apply exclusively to SEBO Vacuum Cleaners which are used residentially No warranty is provided for SEBO vacuum cleaners used commercially EXCLUSIVE REMEDY The remedies provided under the terms of this Warranty the purchaser s exclusive remedies and are in lieu of any other remedies otherwise available LIMITATIONS AND EXCLUSIONS SEBO MAKES NO OTHER REPRESENTATIONS OR WARRANTIES EXPRESSED OR IMPLIED AND SPECIFICALLY EXCLUDES THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE WARRANTY DOES NOT COVER Used or secondhand products Products outside of the warranty period Items not manufactured by SEBO e Normal maintenance service e Equipment damaged by improper use accident other casualty or negligence e Machines equipped with nonauthorized attachments or modifications e Machines on which the serial number has been altered or removed SEBO WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUEN TIAL DAMAGES OF ANY KIND OR NATURE THIS DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO THE EXTENT SAID DISCLAIMER IS NOT ALLOWED BY APPLICABLE STATE PROVINCIAL LAW To contact SEBO in Canada Floor Care Equipment Ltd Telephone 800 661 8687 Fax
28. r head Optional for D4 Red Part 9250AM 31 DISCO Optional for all D4 vacuums Black Part 9433AM White Part 9430AM Filters amp Filter Bags 40 Filter Bag Optional Brushes Heads amp Attachments 32 Premium Parquet nozzle Part 7200DG 10 Kombi nozzle Part 726006 Filter Box D 33 TT C Turbo brush Part 6780ER incl 8 filter bags Straight tube 20 Part 1084HG Part 8120AM 35 Hand held Turbo brush Part 6179DA 41 Hospital grade 36 Wall and floor brush Part 1325HG Micro Filter 37 Flat Upholstery nozzle Part 1090HG 38 Extension hose 9 feet Part 1495AM 39 Radiator brush Part 1496DG incl 1 micro filter 17 AIRBELT Available in several colors and 1 motor filter and patterns Part 6047AM 01 08 Part 8191 42 Motor Filter Micro Filter Box Push the neck 14 of the hose 11 into the suction opening of the canister 19 When all four notches are lined up correctly the neck will snap firmly into place To release the hose from the suction opening squeeze the release tabs 13 on both sides of the neck of the hose 14 and pull the neck out Connect the handle grip 1 to the top of the telescopic tube 5 Snap in place To release the telescopic tube 5 from the han dle grip push the handle release button 3 and slide the handle out Attach the head or brush to the bottom of the telescopic tube 5 Insert the bottom of the telescopic tube
29. r into one groove 55 and while holding it down stretch the AIRBELT cover around the foam 54 into the opposite groove 55 Continue around the vacuum Secure the ends with the clip 23 SEBO AIRBELT covers are available in a variety of colors and patterns See AIRBELT Cover Part 6047AM 01 08 your SEBO dealer for available selection Figure 27 Note Never operate the vacuum with incorrectly attached filters or without filters bag AIRBELT or filter bag housing cover 18 Do not re use filter bags Do not wash and re use filters Changing the Motor Filter Figures 28 amp 29 A The motor filter 42 needs to be changed when it becomes extremely dirty or clogged remove the motor filter switch off the power and unplug the vacuum Lift the cover release catch 15 figure 28 and raise the filter bag cover 18 Pull the filter 42 out 7 by grasping the rubber rim 57 figure 29 of the filter and pulling it out of the groove 56 inset figure 29 that holds it Fit the new filter into the groove and push the rub ber rim snugly into the groove all the way around the filter edge Do not leave any loose edges Close the filter bag cover making sure that the cover release catch snaps back into place Motor Filter Changing the Hospital grade Micro Filter Figures 30 31 32 amp 33 After 10 to 20 bags have been used change the micro filter 41 To remove the micro filter switch off t
30. rade Micro Filter sesesososessssesssssssssossesesssessssceosososososososcscscecscesoso 12 CLOG REMOVAL 13 CLOGS ead Ol 3 Clogs im tine Telescope teaser eee ademas 13 Gogs ar HS OSC 13 Clogs m Entrance Filter Bag 13 Troubleshooting CUE 14 AIRBELT D4 Schematic and Part 15 Warranty E 16 HOW Contact 16 TECHNICAL DETAILS Vacuum motor 1250 watts 12 amps Water lift at motor 95 inches Airflow at motor 120 CFM Filter bag capacity 1 5 gallons Sound level 61 dBA Body weight 15 9 lbs Motor protection Thermal cut out Cord length 40 feet Range 50 feet Technical details may be subject to change IMPORTANT SAFETY INSTRUCTIONS 1 10 11 12 13 14 19 16 17 18 19 READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE When using an electrical appliance basic precautions must always be followed To reduce the risk of electric shock this vacuum cleaner has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not f
31. ription 1 8001WEER Bottom casing 2 2 8086 Castor cpl 3 8065ER Micro filter seal 4 8191AM Hospital grade micro filter amp b Motor filter Microfilter set 5 8084ER Micro filter holder 6 8120AM Filter bag 7 8045ER Motor support 8 8091AM Internal cable set 9 8048ER 1200W Vac motor 7 amp 8 10 665613E Cord reel 11 8009 Motor inlet seal 12 8098ER Rewind lever spring 13 8036ER Rewind lever cpl 12 14 8085ER Motor cover cpl 11 amp 13 15 8106ER PCB w switch 16 8058ER Retaining ring 17 8038ER1 Power display 18 8057 Spring for power button 19 803765 Power button 20 6047AM 01 AIRBELT cover dark gray 21 8033UL Foam bumper 22 803465 AIRBELT clip 23 8140ER Filter bag spring w hardware 24 6750ER Bag cover axle 25 8052ER Bag cover hinge 2 pcs 26 8003WEER Top casing 23 25 27 8059GS Cable entry 28 8010PRER Attachment holder cpl 29 8114ER Bag cover release w axle amp spring 30 8129GS Bag cover insert 31 8079GS Hose neck 32 7020ER Bag indicator 33 8127ER Bag indicator adjuster 34 8130 Bag cover seal 35 8051AM4 Inside cover cpl 30 34 47 amp 50 36 8005WEER Bag cover 37 6270GS Telescopic tube 38 amp 39 38 642065 Release button leaf spring amp cap 39 6421GS Slider button w hardware 40 814265 Upholstery nozzle 41 8146ER Dusting brush horsehair 42 8066GS Crevice nozzle 43 6391DA Parquet nozzle 44 5266 Cable clamp 45 8119AM 7 handle with hose 46 01000 Screw C 2 9 x 16 47 01036 Screw 4x 14 A gt 48 0102 Screw F 3
32. so clear clogs by reversing the hose see 2 below 2 With the power off remove the hose neck 14 figure 36 from the suction opening 19 by squeezing the two release buttons 13 Remove the handle grip 1 from the tel escopic tube figure 37 and insert the handle end of the hose 1 into the suction open ing figure 38 Note the handle will not fit snugly into the suction opening Then hold the hose upright with one hand blocking the hose neck end and switch on the machine at full suction power If necessary quickly lift your hand on and off the neck end of the hose figure 38 After the clog is removed replace the hose in the correct position Note Do not insert a wire or stick into the hose Doing so may cause damage to the Figure 36 Figure 29 Clogs in Entrance to Filter Bag Figure 39 Remove hose neck 14 from vacuum cleaner see figure 36 open the filter bag cover see 11 and clean out entrance to bag 66 Figure 38 Figure 39 TROUBLE SHOOTING GUIDE Always unplug vacuum from outlet before dismantling part of the machine PROBLEM REASON SOLUTION Does not turn on Bag full or clog light on Bag full or clog light on amp machine shuts off Does not pick up Filter bag door won t fully close 1 Telescopic tube not inserted properly 1 See page 7 2 Not plugged into working outlet 2 Use another outlet 3 Cable worn 3 Replace cable 4 The power contro
33. um openings Do not use machine with any openings blocked Keep openings free of lint hair and anything that may reduce air flow Do not re use filter bags or wash the filters Do not remove any screws from vacuum Do not vacuum up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use vacuum without filter bag and or filters in place Turn off all machine controls before unplugging Use extra care when cleaning on stairs Do not use machine to vacuum up flammable or combustible liquids such as gasoline or use In areas where they may be present 20 21 22 23 24 29 26 27 28 29 30 31 32 33 34 Machines can cause a fire when operated near flammable vapors or materials Do not operate this vacuum near flammable fluids dust or vapors Maintenance and repairs must be done by qualified personnel Use only original SEBO replacement parts Do not use vacuum as a step If vacuum is used on plush carpet or carpet with thick padding do not leave machine standing in one place with machine turned on While the vacuum is in use the power cord should be unwound from the cable reel at least two thirds of its length Hold plug when rewinding onto the cord reel Do not allow plug to whip while rewinding Keep hair loose clothing fingers and all parts of body away from vacuum openings and moving parts Do not place fingers or other body parts under vacu
34. um unless it is unplugged Do not place the power head over rug or carpet edges The vacuum has a manual reset thermal protector The protector is reset by switching off the vacuum The thermal protector needs some time to cool down after switching off Check the vacuum for air blockages or mechanical failures before switching on Store the vacuum in a dry place at room temperature When the vacuum 15 not in use you should rewind the cord onto the cord reel Any other servicing should be performed by an authorized service representative The hose contains electrical wires Do not use if damaged cut or punctured Avoid picking up sharp objects Always unplug vacuum before connecting or disconnecting either hose or power head Use a SEBO power head only in combination with a SEBO vacuum Cleaner Do not connect power head to a malfunctioning or damaged vacuum SEBO AIRBELT D4 PRODUCT FEATURES The SEBO AIRBELT D4 is equipped with many extras that will make your life easier Its suction optimized airflow pathway together with its one of a kind tapered hose technology provides ultra quiet operation and amazing suction power And the ergonomically designed handle offers unmatched user comfort and smooth oper ating maneuverability Every detail expresses the highest quality modern design reliability and the standard features SEBO cus tomers throughout the world have come to expect such as SEBO s patented AIRBELT B
35. umper Guard e A power head with amazing steering ability and easy brush roller removal An adjustable telescopic tube with internal power cord Long lasting motor life which is further extended by its soft start switch S class hospital grade filtration which is excellent for users with allergies or asthma Available in three colors black red and white A generous five year warranty on both labor and all non wear parts SEBO Vacuums Save Money SEBO vacuums are the highest quality machines available In fact if properly maintained SEBO vacuums can Save ordinary residential users hundreds of dol lars by providing excellent performance for ten to fifteen years or more Typical vacuums perform poorly and usually do not last beyond two years So in the long run SEBO vacuums cost less money than the five to six other vacuums purchased during that time period Outstanding Warranty Coverage SEBO is confident about the quality of all its vacuums Therefore all models include a five year warranty on the motor and all non wear parts Bag Full or Clog Indicator amp Auto Shut The BAG FULL OR CLOG indicator located on top of the canister near the ON OFF power con trol knob will turn orange and the machine will automatically shut off when it senses a full bag a clog in the airflow pathway or an excessively dirty micro filter If the user ignores this warning the suction motor will heat up due to the lack of
36. uum off unplug it from the outlet then press the cord rewind button 7 figure 13 and the mechanism will automatically rewind the cord You must hold the button down until the cord is fully rewound Hold plug while rewinding into the cord wheel Do not allow the plug to whip while rewinding The rewind mechanism will stop automatically when you release the button Before rewinding the cable always switch off and unplug the vac uum LED Suction Power Indicator Figure 14 Your AIRBELT D4 canster features an LED light display 8 that monitors suction power It is located around the ON OFF power control knob 6 When the canister power is switched on a blue light will blink right and left As the suction increases the lights will rotate around the ring The faster the rotation the higher the suction Storing the Vacuum Figures 15 16 amp 17 The vacuum can be stored with the canister in a horizontal or vertical position The standard Parquet brush has a parking tab located on the back of the neck The optional Premium Parquet Kombi and Turbo nozzles have a parking tab located on the front of the neck 45 Insert the parking tab into the upper side of the parking groove and slide down firmly For vertical storage or for easy carrying use the parking slot on the underside 26 For horizontal storage use the parking slot on the end of the canis ter 21 Figure 19 Figure 16 Figure 17 USE AND MAINTENANCE OF BRUSHES amp
Download Pdf Manuals
Related Search