Sears 175.867029 User's Manual
Contents
1. Trigger Valve Twist clockwise to lock See DETAIL A Fig 3 Angled Wand and Straight Wands Connect other end of Tubing to Carpet Tool Vacuum Inlet Coupling of the Solution Tank See DETAIL B Fig 3 NOTE To remove the Plastic insert depress the Tab TRIGGER and gently pull on the Plastic Insert Be careful to pull VALVE UCR B CONN T onthe Plastic Insert and not the Tubing as damage may NUT RETAINING occur CLIP INLET PLASTIC INSERT VACUUM HOSE COUPLING DETAIL B Fig 3 OPERATION CARPET PREPARATION For best results prepare carpet for cleaning as follows 1 Vacuum carpet to remove loose dirt before using Cleaner 2 To remove stains and ground in dirt present in heavy traffic areas of the carpet spray or rub Sears Heavy Traffic Pre Treatment 82833 into carpet before using Cleaner Follow directions on the bottle FILLING CLEANER WITH WATER AND FILLER CLEANING SOLUTION See Figure 4 A SOLUTION 1 Open lid of the Filler Opening A TANK 2 Add Sears All In One Carpet Cleaner 82813 solution or Sears Upholstery Cleaner 82843 solution to Solution Tank depending on type of cleaning to be performed Follow directions on label of bottle i 3 Pour clean hot water from tap into Filler Opening in the Solution Tank use two 2 gallons of water 4 Ciose Filler Opening NOTE This unit may become damaged if boiling water is used POWER CORD AND SWITCH See2. 643508 001 642149 004 641843 010 842367 006 644548 001 642367 004 643909 902 642367 004 642406 016 641857 012 641866 039 640145 005 643584 000 642405 001 643579 002 642313 000 662252 001 642046 016 968702 007 641798 002 642627 001 642470 006 640218 005 706382 319 644773 008 642603 061 643565 016 643581 000 644802 001 642382 003 643562 003 843535 001 843438 002 643536 000 643566 015 643531 005 843533 092 888493 204 643685 001 989829 002 860081 002 640940 001 843431 010 843454 003 643583 000 643685 001 643498 000 644089 014 543171 003 662381 001 968702 007 20 5086 661654 148 DESCRIPTION Switeh Cap Handle Plate Label Handle Shroud w Label Motor Housing Screw Switch Scrows 2 Female Pigtail Switch Wiring Nut 4 Power Card Motor Seal Motor Cover Motor Seal _ Carbon Brush Asm 2 Motor Seal Motor Asm Complete os 555S S Latch 2 Cover Asm w 19 20 21 22 Cover Screws 4 Foam Filter Valve Asm w 21 22 Valve Screws 2 Sansor Guard Adapter Dirt Container w 23 25 Baffle Scraws 2 Separator Plate Screw Gasket Kit Rivet Wave Washer Washer 2 Coupling Body Separater Plate w 7 9 27 Upper Container w Filler Door Retaining Ring Ground Lead Screw Lead w terminal Tubing Asm w 31 34 39 Valve Seat Screws 2 Valve Seat Gasket Lower Container Pigtail Lower Container Screws 3 Strain Reliet Motor Screws 2 Lateh Screw L
3. The Squeegee Attachment 2 is useful for WET pick up CAUTION DO NOT run the Pump Motor when using these attachments To prevent Pump Motor from operating make sure Pump Motor is in OFF position or unplug the short Power Cord from the Solution Tank to the Recovery Tank OPTIONAL CLEANING ACCESSORIES Optional cleaning accessories may be purchasad or ordered through your nearest Sears store A complete set of instructions comes with each attachment set KENMORE SPRAYMATE ATTACHMENT Model No 83252 See Figure 15 Cleanmore Sprayrnate is an optional attachment for carpet cleaning The Cleanrnore Spraymate has a motorized beater brush which is especially good for difficult to clean areas of heavy traffic TROUBLE SHOOTING CHART PROBLEM POSSIBLE SOLUTIONS 1 Neither vacuum motor nor pump Be sure power switch is in ON position rnotor runs Be sure power cord is plugged in securely Check wall electrical outlet by plugging in a known working electrical appliance 2 Vacuum motor runs but there is no Be sure Electrical Cord from Power Head to Solution spray at the nozzle Tank is securely plugged into receptacle on the Power Head Check that Solution Tank is full Be sure Pump Switch is in the HI or LO position Nozzle Ports may be clogged See illustration below to unclog 3 Spray from the floor nozzle comes Unclog the Nozzle Part See illustration below out of one side of the nozzle
4. figure 5 SWITCH 1 Plug Power Cord into electrical outlet 2 Tum Power Switch to ON position Continued OPERATION TEST FOR SOLUTION SPRAY See Figure 6 1 Hold Floor Nozzle above floor level 2 Pull Solution Release Trigger on Angled Wand SOLUTION 3 Observe Floor Nozzle to make sure cleaning solution RELEASE is being sprayed evenly see DETAIL A TRIGGER NOTE If solution is not being sprayed evenly refer to Trouble Shooting Chart NOZZLE SPRAYS OF SOLUTION Fig 6 CLEANING THE CARPET See Figures 7 8 8 Solution Dispensing Stroke 1 Start at a comer recommended 2 Place Floor Nozzle so Suction inlets are flush with carpet 3 While exerting light pressure down on Floor Nozzle depress Solution Release trigger and slowly pull Floor Nozzle towards you NOTE Do not overwet If three or more cleaning strokes are required let dry and then repeat cleaning proc ess SUCTION INLETS SET FORWARD Solution Recovery Stroke 2 2 PULL BACK ACROSS CARPET 1 Release Solution Release Trigger 2 Lift Floor Nozzle off carpet 3 Retum Floor Nozzle to point where you dispensed cleaning solution and pull across carpet recovering dirty solution OPERATION WHEN TO EMPTY RECOVERY TANK See Figure 9 During normal operation your cleaner may stop recovering solution from your carpet When this occurs there are three check points to alert you 1 An increase in motor noise 2
5. only 4 Motor runs but cleaner does not pick Recovery Tank is full of dirty water and must be emptied up solution from carpet no exhaust Check for clogged hose or nozzle Clogs could resultfrom frorn top of cleaner picking up material such as carpet strings shoe laces etc S Spray connections leak Disassemble nut at leaking connection Be sure washer is properly seated Reassemble and tighten securely Ifthe Possible Solutions to Problems listed inthe chart do not correct the problem take your cleaner to a Sears Service Center for professional service Repairs not listed in this chart require professional and specific knowledge of this medel cleaner and could result in safety hazards and personal injury if not made by a qualifiad Sears Service Technician TO UNCLOG NOZZLE PO RT CAUTION Do not let needie See Figure 16 or pin touch this surface 1 Insert the point of a needle or pin into Spray Port to unclog NOTE Do not let the point of needle or pin SPRAY PORT touch any part of the Spray Pad surface or Spray Pad will not spray solution properly NEEDLE OR PIN SEARS HOME CLEANING SYSTEM MODEL 175 8670290 EXPLODED VIEW Ni ca NAJ Y Hi Y RS E TT I J no X A AA SEARS HOME CLEANING SYSTEM MODEL 175 8670290 SEARS HOME CLEANING SYSTEM MODEL 175 8670290 PART NO 642315 012 644125 007 642600 039 641798 004 641838 001 643741 002
6. parts NEVER vacuum materials such as hot coals cigarete butts matches ate When dry vacuuming do not use without filter in place Turn off ali controls before unplugzing Use extra care when using on stairs Do not use to pick up flammable or ccmbustible liquids such as gasoline or use in areas where such liquids may be ic SAV THESE INSTRUCTIONS TABLE OF CONTENTS Safety Instructions ies page 2 Additional Uses Optional Accessories page 8 9 Warrants page 3 Trouble Shooting Chart nn page 10 introduction A A rs page 3 Exploded Views and Parts Lists page 11 15 A A A ss ais ie nana iais page 16 Operation i iii dan ani A page 5 8 S FULL ONE YEAR WARRANTY When used for private household purposes if within one year from the date of purchase this vacuum cleaner fails due to a defect in material or workmanship RETURN IT TO THE NEAREST SEARS SERVICE CENTER DEPARTMENT IN THE UNITED STATES and Sears will repair it free of charge If this vacuum cleaner is used for commercial or rental purposes the above warranty coverage applies for only 90 days from the date of purchase This warranty gives you specific legal rights and you may also have other rights which vary from state to state SEARS ROEBUCK AND CO D 731CR W SEARS TOWER CHICAGO IL 60684 INTRODUCTION Your new Kenmore Home Cleaning Systemis a deluxe high pe
7. rary adapter should be used only until a properly grounded outlet see figure A can be installed by a qualified electrician The tab for grounding screw see figure B extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adapter is in use it must be held in place by a metal serew see Figure B dance with all local codes and ordinances WARNING Improper connection of the equipment grounding con duetor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outletis properly grounded DO NOT modity the plug provided with the vacuum cleaner ifit will not fit the outlet have a proper outlet installed by a qualified electrician This vacuum cleaner is for use on a nomina 120 volt circuit and has agrounded plug see figure A A temporary adapter see figure B may be used to connect this plug to a 2 pole receplacle see figure B if a properly grounded outlet is not available The tempo 2 POLE RECEPTACLE DISCONNECT POWER CORD FROM ELECTRICAL OUTLET before the recovery tank is ernptied the solution tank is refilled or the cleaner is serviced in any way DO NOT store this cieaner in an area which may reach freezing temperatures Should this occur DO NOT operate this cleaner until it has been at room temperature for at least two 2 hours DO NOT use any cleaning solution or chemical
8. No solution visibly being recovered by the floor nozzle 3 No air coming from the exhaust port of your cleaner When this occurs 1 The Recovery Tank is full and the Float Valve in the Recovery Tank has been activated The Recovery Tank should be emptied 2 The Recovery Tank has foam in the Tank and the Float Valve has been activated NOTE If cleaner is accidently turned over while in operation the float may activate and shut off the suction If this occurs set the cleaner upright Tum Power Switch OFF and et motor come to a complete stop Then turn switch back on and continue cleaning TO EMPTY RECOVERY TANK See Figure 10 1 Turn Power Switch OFF and Disconnect Power Cord from Electrical Outlet 2 Disconnect Short Cord located between Solution Tankand Recovery Tank 3 Disconnect Vacuum Hose by depressing the Lock Button and remov 4 Push Tab inward on Plastic Coupling and remove Plastic Insert and Tubing See DETAIL A 5 Lift Latehes on Power Head 6 Lift power Head by Handle and remove from Recovery Tank 7 Rotate Metal Latch on the Solution Tank and lift Recovery Tank from the Solution Tank 8 Empty Recovery Tank 9 Reassemble cleaner and resume cleaning NOTE Power Head is designed to go on in only one position Make sure the word VACUUM on the Power Head is lined up directly over the Hose Inlet on Recovery Tank as shown in Fig 10 or Power Head will not seal to unit properiy EXHAU
9. SEARS OWNERS MANUAL HOME CLEANING SYSTEM MODEL NO 175 8670290 CAUTION Read Instructions and Rules for Safe Operation Renmore Carefully HOME CLEANING SYSTEM For Household Use Only e INTRODUCTION e ASSEMBLY Save this e OPERATION Manual for MAINTENANCE Future Reference e REPAIR PARTS SEARS ROEBUCK AND CO Dept D 731 CR W Sears Tower Chicago IL 50684 661654 146 0683 Rev 0000 FSINTED IN U S A l M PO RTANT SAFETY INSTR U CTIONS Read all instructions before using this cleaner When using any electrical appliance basic precautions should always be followed including the following WARNING To reduce the risk of fire electric shock or injury 1 Do not leave cleaner when plugged into electrical outlet Unplug from outlet when not in use and before servicing 2 WARNING TO AVOID ELECTRIC SHOCK DO NOT EXPOSE TO RAIN STORE INDOORS 3 WARNING DO NOT REMOVE GROUNDING PRONG FROM POWER CORD PLUG Connect to a properly grounded outlet ONLY See Grounding Instructions GROUNDING INSTRUCTIONS This vacuum cleaner must be grounded If it should malfunction or break down grounding provides a path of least resistance for electrical current to reduce the risk of electric shock This vacuum cleaner is equipped with a cord having an eguipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accor
10. ST RECOVERY PORT VIRS TTT LOCK BUTTON a Nu A VACUUM HOSE DETAIL A SOLUTION TUBING OPERATION TO EMPTY THE SOLUTION TANK See Figure 11 When cleaning is completed both the Recovery Tank and the Solution Tank should be emptied prior to storage Empty the Recovery Tank as described earlier There are three methods of emptying the Solution Tank Method 1 1 Disconnect Pump Cord from Recovery Tank 2 Remove Recovery Tank from Solution Tank and pour solution out of the Filler Opening Method 2 1 Place Floor Nozzle in bath tub or container 2 Depress Solution Release Trigger and spray until empty Method 3 1 Remove Floor No22le and insert Wand into Solution Tank through the Filler Opening 2 Vacuum solution out 3 All solution is now in Recovery Tank Empty Recovery Tank as described earlier ADDITIONAL USES DRY VACUUMING See Figure 12 Your Cleaner comes with a disposable paper dust bag to trap and collect dirt when used for dry pick up it is very important that the disposable paper dust bag remain clean to allow air to pass through it while trapping dirt If the dust bag is over filled or its pores become clogged from fine powders no air can pass through This greatly reduces the efficiency of your cleaner and could cause the dust bag to burst To maintain your cleaner s peak efficiency check the disposable paper dust bag often and replace when clogged or approximately one half f
11. atch Spacer Filler Door Washers 3 Foam Filter Motor Screws 4 Casters 3 Purnp Mator O Ring Splash Plate Screws 2 Paper Dust Bag Owner s Manual SEARS HOME CLEANING SYSTEM MODEL 175 8670290 SEARS HOME CLEANING SYSTEM MODEL 175 8670290 x VB m Ba Na PART NO 662257 001 662262 001 644037 002 644848 006 643731 005 644038 003 644773 005 644773 007 643502 009 643570 023 661404 003 663324 001 644038 001 643572 007 662266 001 662266 002 662264 001 662263 001 643186 01B 643571 013 644159 003 643076 009 642458 005 643737 013 663324 002 661654 146 DESCRIPTION Angled Wand w Key 2 14 Trigger Ferrule Nut 2 Swivel Connector 1 1 4 dia Tubing Strap 2 Tubing Hose Coupling Insert Nut Coupling Insert Swivel Connector 2 1 2 dia Hose and Angled Wand Asm 8 Hose w Key 4 9 Quick Disconnect Nut Tubing to Nozzle Valve Asm Kit w trigger O Ring O Ring 2 Valve Shut Off Spring Valve Straight Wands 2 Nozzle Asm Complete w Key 3 12 13 Retaining Clip Bare Floor Carpet Brush Wet Squeegee Nozzle Wet Upholstery Nozzle Asm Nut w O Ring Owner s Manual SEARS OWNERS MANUAL SERVICE MODEL NO 175 8670290 HOW TO ORDER REPAIR PARTS Kenmore HOME CLEANING SYSTEM Now that you have purchased your Kenmore Home Cleaning System should aneed ever exist for repair parts or service simply contact any Sears Service Center B
12. e sure to provide all pertinent facts when you call or visit The model number of your Power Spray Cleaner will be located on the Power Head of the cleaner WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOLLOWING INFORMATION PART NUMBER PART DESCRIPTION MODEL NUMBER NAME OF ITEM 175 8670290 Kenmore Horne Cleaning System All parts listed may be ordered from any Sears Service Center If the parts you need are not stocked locally your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling SEARS ROEBUCK AND CO Dept D 731 CR W Sears Tower Chicago IL 60684
13. rformance cleaner designed for today s cleaning requirements With proper care and maintenance it should provide you with years of service It is important that you read this manual to fully understand the cleaner s capabilities as well as providing you with the essentials regarding maintenance and safety A complete list of operating parts and features is shown in figure 1 below ANGLED WAND POWER SWITCH RECOVERY TANK POWER HEAD RECOVERY TANK VACUUM HOSE SOLUTION TANK SOLUTION TUBING FLOOR NOZZLE Fig 1 ASSEMBLY OF RECOVERY TANK AND SOLUTION TANK See Figure 2 1 ASSEMBLY OF HOSE WANDS NOZZLE AND SOLUTION TUBING See Figure 1 1 2 3 Push the Solution Tube Quick Disconnect Nut onto Snap Solution Tubing into Retaining Clips on the Attach the Vacuum Hose to Recovery Tank inlet Insert the Plastic Insert of the Solution Tubing into the ASSEMBLY Place Recovery Tank into Solution Tank align the word VACUUM on Recovery Tank with VACUUM on Solution Tank and secure with Metal Latch Insertthe plug onthe Short Cord from the Solution Tank RECOVERY into the Recovery Tank Power Head TANK Assemble the two Straight Wands SOLUTION Assemblethe upper Straight Wandtothe Angled Wand ik TANK of the Hose Assemble the Floor Nozzle to the lower Straight Wand NOTE Be sure locking button engages properly when assembling straight wands angled wand and floor nozzle
14. s other than those discussed in this manual For maximum efficiency empty container frequently and keep inside of hose wands nozzle and container clean DO NOT overwet carpet or upholstery If three or more cleaning strokes are required let the carpet or upholstery material dry and then repeat cleaning process Do not allow children to operate cleaner nor should they play with cleaner as atoy Close attention is necessary when used around or near children Use this cleaner ONLY for its intended use as described in this manual Use only the attachments recommended in this manual Always turn cleaner OFF when connecting or disconnecting the Spraymate motorized nozzle Do not use with damaged cord or plug If cleaner is not working properly has been dropped damaged left outdoors or dropped into water return it to a Sears Service Center Do not pull or carry by cord nor use cord as a handle nor close a door on cord nor puli cord around sharp edges or corners Do nat run cleaner over cord Keep away from heated surfaces Do not unplug from electrical outlet by pulling on ihe cord To unplug grasp the plug not the cord and pull Do not handle plug or cleaner with wet hands Do not put any objects in ventilation openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air tlow Keep hair loose clothing fingers and all parts of the body away from openings and moving
15. ull TO INSTALL DUST BAG i 1 TURN POWER SWITCH OFF AND DISCONNECT POWER CORD FROM ELECTRICAL OUTLET 2 Lift Latches and remove Power Head from Unit 3 Grasp Cardboard Collar of Dust Bag and push Collar as far as possible onto Bag Adapter Tube NOTE For greater ease in assembly slide bottom of Cardboard Collar onto Adapter Tube first then pull top of Collar over Adapter Tube 4 Position Dust Bag around sides of tank to allow motor assembly to fit back into unit 5 Bend top flap of Cardboard Collar inward BAG ADAPTER 6 Replace Power Head on unit aligning the word TUBE VACUUM with Hose Inlet on Recovery Tank as shown in Fig 10 NOTE Be careful not to crush Dust Bag or to deform flexible splash plate on Power Mead when SAUTION PAPER DUST BAG IS FOR DRY PICK UP assembling ONLY DO NOT USE WHEN VACUUMING UP WATER OR 7 Unplug Short Power Cord from Recovery Tank Power OTHER LIQUIDS Head See Figure 2 page 4 CARDBOARD ATTACHMENTS UPHOLSTERY NOZZLE See Figure 13 The Carpet Cleaner Upholstery Nozzle is an attachment for furniture upholstery cleaning The upholstery nozzle may also be used to clean auto upholstery or carpeting In addition the nozzle may also be used to clean carpeted stairs and other areas difficuk to clean with the normal floor nozzle FLOOR TOOLS See Figure 14 The Bare Floor Carpet Brush 1 may be used on floors without carpet for DRY cleaning with Paper Dust Bag installed
Download Pdf Manuals
Related Search