Schwinn Runabout Trailer Owner's Manual
Contents
1. satisfied with your selection Although great care has been taken to assure the highest quality some problems may occur PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE To ensure prompt and correct handling of your problem or to answer any questions you may have please contact our Toll Free Customer Service Number listed below Please have the model number found on carton or manual and assembly instructions ready when calling If neither is available please tell us the name of the product in question For questions concerning the safe use of this product please contact Schwinn at 1 800 242 6110 E mail info instep net Web site www instep net 3 ASSEMBLY AND OPERATING INSTRUCTIONS Open carton remove contents and compare contents with parts list Note To prevent scratching of the frame it is recommended that you lay the parts out on top of a flattened cardboard box or other soft surface 1 Remove all contents from the carton Check to make sure nothing is left in the box 2 Unwrap all parts and compare them with the parts list and the above picture Make sure nothing is missing STEP 1 Attaching the folding trailer arm 1A 1B 1A Position the trailer arm to the Runabout frame as shown Line up the three holes to begin assembling the hinge 1B Insert the receiving half of the frame pivot bolt through the three holes and insert the screw to the pivot bolt Use the Allen wrench to tighten 4 STEP 2 Extend the folding tr2. secure WARNING Always use the safety flag when riding with this product STEP 10 Straddle the adult bike while the child climbs onto the trailer bike WARNING The adult bike kickstand is not designed to support the additional weight of a child seated on the trailer bike The adult pulling the child should always straddle the adult bike whenever the child is seated on the trailer bike or getting on and off the trailer bike WARNING Always wear an approved safety helmet when riding 1 2 3 4 8 STEP 11 Remove the Runabout from the adult bike 11A 11B 11C 11A Flip the quick release lever up and unscrew the nut from the other side 11B Remove the nut and slide the quick release bolt completely out 11C Slide the coupler assembly out from the seat post clamp Replace quick release pin STEP 12 Reattach the Runabout to the adult bike 12A 12B 12C 12D 12A Slide the square coupler assembly tube into the seat post clamp 12B Align the holes in the coupler assembly and seat post clamp tubes and slide the quick release bolt through 12C Screw the nut over the threaded end of the pin and tighten with your fingers 12D Clamp the quick release lever all the way down STEP 13 Maintenance 13A Inflate tires with a hand or foot pump to the correct PSI reading shown on the tire 13B Lube the chain monthly or as needed with bicycle chain oil 13C Check all fasteners before each use to make sure they are all secure
3. 1 Runabout Model 13 SC250 SC350 Trailer Owner s Manual Please keep this Owner s Manual for future reference If you sell or give this product away please include this Owner s Manual and ask the new owner to read the instructions completely before operating PRIOR TO ASSEMBLY Please read this Owner s Manual completely before assembling or operating this product Assembly of this product should be carried out by an adult Parts are wrapped in paper or protective covering to prevent damage during shipment Remove all parts and packing materials from the box prior to assembly Save all packing materials until assembly is complete to make sure no parts are accidentally thrown away After assembly is complete properly discard all waste Refer to the Parts List and Diagram on page two of this manual to make sure all parts are accounted for Do not return this product to the store If any parts are missing or damaged please contact one of our Customer Service Representatives by phone at 1 800 242 6110 or by e mail at Info instep net IMPORTANT SAFETY INFORMATION WARNING Always wear an approved safety helmet when riding WARNING Never leave your child unattended on this product WARNING This trailer bike is designed to attach to an adult bicycle with 26 27 or 700C wheels WARNING This trailer bike does not have a brake Make sure the adult bike brakes function properly WARNING Recommended for ages 4 through 9 Maximu
4. If you have any questions about the proper assembly or safe use of this product please contact one of our Customer Service Representatives at 1 800 242 6110 or by e mail at info instep net 9 ACCESSORIES FOR YOUR RUNABOUT TRAILER BIKE Additional Coupler Kits allow you to switch your PATHFINDER from one bike to another The PATHFINDER Coupler Kit includes the seat post clamp four bolts and the Q R pin bolt PF001 Cut Here Cut Here Bike Trailer Accessory Order Form Model Item Cost Shipping amp Handling Quantity Amount PF001 RUNABOUT Coupler Kit 8 99 3 00 U S and Canada IL residents add sales tax All prices are in US Canadian tax and duty are not included TOTAL AMOUNT OF ORDER How to Order Order accessories in one of four convenient ways 1 Mail this form with a check or VISA or Master Card number listed to Pacific Cycle LLC 4730 East Radio Tower Lane Olney IL 62450 2 Fax this form with Credit Card information to 1 800 858 2800 3 Call our Customer Service Dept at 1 800 242 6110 4 Order on line at our web site www instep net Please allow 7 to 10 business days for your shipment to arrive VISA or Master Card Only _________________________________________________________________ Card Number Expiration Date _________________________________________________________________ Ca
5. ailer arm 2A 2B 2A Extend the trailer arm until the two frame ends are flush together If necessary move the quick release bolt and knob out of the way 2B Position the square head of the bolt into the squared spot on the frame and screw on the quick release knob to the other side Tighten the knob so that the arm can t move STEP 3 Attach the handlebar 3A 3B 3C 3D 3A Unscrew the two Allen head screws using a 5mm Allen wrench and remove the handlebar clamp 3B Place the handlebar into the groove of the clamp base with the handlebar grips toward the rear of the trailer bike 3C Replace the clamp over the handlebar insert both Allen head screws back into the clamp and tighten with your fingers 3D Adjust the handlebar to the desired position and tighten both screws securely with the Allen wrench IMPORTANT NOTE As you tighten the screws alternate among both to make sure they are tightened evenly When properly tightened the handlebar should not move 5 STEP 4 Attach the handlebar foam then fold the trailer arm 4A 4B 4C 4D Check to see if the handlebar pad is properly attached If it is not follow steps 4A and 4B 4A Remove the cover from the foam pad and slide the foam pad over the handlebar crossbar so the opening is on the bottom 4B Wrap the cover around the foam pad and secure along the bottom edge 4C Loosen the QR skewer on the trailer arm and rotate the plate out of the way 4D Fold t
6. he arm under the trailer bike The handlebar will allow the unit to stand up making the remaining assembly steps easier STEP 5 Attach the pedals to the cranks 5A 5B 5C 5A Locate the right pedal marked with an R at the end of the threaded shaft and the left pedal marked with an L at the end of the threaded shaft 5B Thread the right pedal clockwise into the right crank arm the side with the chain by hand Tighten using an adjustable or 15mm wrench 5C Thread the left pedal counter clockwise into the left crank arm the side opposite the chain by hand Tighten using an adjustable or 15mm wrench 6 STEP 6 Install the seat post assembly and adjust the seat 6A 6B 6C 6A Loosen the seat post quick release skewer 6B Slide the tube of the seat post assembly into the frame seat tube to a depth of at least 2 1 2 inches WARNING Minimum insertion line must be completely inserted into frame and must not be visible 6C Adjust the seat to the desired height With the seat facing forward tighten the seat post down with the quick release skewer Make sure the seat does not spin or move up and down STEP 7 Prepare coupler for attachment of Runabout to adult bike 7A 7B 7C 7D 7A Adjust the height of the adult bike seat to allow space for the coupler to clamp to the seat post Re tighten the seat post securely so it does not spin 7B Attach the coupler with the included bolt and nut and tigh
7. m weight capacity of rider is 75 pounds WARNING Make sure the child riding the trailer bike understands how to operate it correctly WARNING Always use the safety flag when riding with this product WARNING A bicycle with the trailer bike attached requires a wide turning radius Use caution when turning WARNING Do not ride over curbs Avoid bumps and potholes Do not turn sharply WARNING Before riding check that all parts are assembled correctly per the manufacturer s instructions WARNING Tire should be inflated to the pressure reading shown on the tire sidewall Check before each use WARNING Use a foot pump or hand pump to inflate tires Pressurized air hoses can cause overinflation WARNING Do not ride at night WARNING Do not ride barefoot WARNING Do not ride in wet weather or when road surface is slippery WARNING Periodically re check all fasteners to make sure they are tight TOOLS REQUIRED FOR ASSEMBLY Adjustable wrench 6mm Allen wrench 5mm Allen wrench 2 FULLY ASSEMBLED TRAILER BIKE PARTS LIST QTY DESCRIPTION QTY DESCRIPTION 1 Frame w folding trailer arm wheel 1 Seat post assembly w seat chain w guard crank red rear reflector and bracket 1 Coupler assembly 1 Left pedal 1 Handlebar w grips and pad w cover 1 Right pedal 1 Frame pivot bolt 1 Safety flag w poles and joiner 1 Frame quick release IMPORTANT We appreciate your purchase of this product and hope you will be completely
8. rdholder Signature Ship To Name ____________________________________________________ Street Address ____________________________________________________ City State Zip ____________________________________________________ Contact Phone ____________________________________________________ Contact E mail ____________________________________________________ Prices are subject to change Visit www instep net for updated pricing
9. ten securely with an adjustable wrench 7C Unscrew the four bolts on the coupler assembly that hold the seat post clamp plate to the seat post clamp 7D Separate the seat post clamp plate from the seat post clamp Seat post clamp plate Seat post clamp 7 STEP 8 Attach Runabout to adult bike and secure seat post clamp 8A 8B 8C 8D 8A Place the Runabout behind the adult bike with the seat post clamp against the adult bike seat post The seat post should rest in the valley of the seat post clamp 8B Place the seat post clamp plate over the seat post and tighten all four bolts by hand 8C Position the Runabout behind the adult bike so the coupler assembly trailer arm and bike are in a straight line Tighten each bolt one turn with the Allen wrench 8D Tighten all four bolts in a crisscross pattern 1 2 3 4 then repeat until they are tightened equally and the gap between the clamp plate and coupler is even on both sides STEP 9 Insert safety flag check tire pressure and recheck all fasteners 9A 9B 9C 9A Locate the safety flag poles and plastic joiner Join the two poles by inserting one pole into each end of the joiner 9B Insert the safety flag assembly into the bracket next to the trailer bike s rear hub nut 9C The completed product should look like this Check the tire pressure and inflate to correct PSI reading indicated on the tire sidewall Re check all fasteners to make sure that they are all
Download Pdf Manuals
Related Search