Sanyo VM-6609 User's Manual
Contents
1. OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock OBJECT AND LIQUID ENTRY Never push objects of any kind into video monitor or equipment through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product SERVICING Do not attempt to service video monitor or equipment yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel DAMAGE REQUIRING SERVICE Unplug video monitor or equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power supply cord or the plug has been damaged B If liquid has spilled or objects have fallen into the video product C If the video product has been exposed to rain or water D If the video product does not operate normally by following the operating instructions adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation E If the video product has been dropped or the cabinet damaged F When the video product exhibits a distinct change in performance this indicates a n2. COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS CET APPAREIL NUMERIQUE DE LA CLASSE A RESPECTE TOUTES LES EXIGENCES DU REGLEMENT CANADIEN SUR LE MATERIEL CAUSANT DES INTERFERENCES IMPORTANT SAFEGUARDS 1 2 6A 10 11 READ INSTRUCTIONS All the safety and operating instructions should be read before the appliance is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference CLEANING Unplug video monitor or equipment from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Us
3. the rating are exceeded heat may generate and cause a fire Make sure to carefully read the specifications accompanying the extension cord Cleaning e Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth e Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling SERVICE This unit is a precision instruments and if treated with care will provide years of satisfactory performance However in the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Servicing should always be referred to your dealer or Sanyo Authorized Service Centre PARTS NAMES Front Panel A Monitor Selector Switch VIDEO A B Turn this Monitor selector switch A position for a signal fed through the rear panel VIDEO A connectors Then turn this Monitor selector switch B position for a signal fed through the rear panel VIDEO B connectors Contrast Control CONTRAST Turn to adjust picture contrast according to your requirement Brightness Control BRIGHT Turn to adju
4. AGES RESULTING FROM ANY CAUSE WHATSOEVER ARISING OUT OF OR IN CONNECTION WITH THE SALE USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR S NEGLIGENCE ALLEGED DAMAGED OR DEFECTIIVE GOODS WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT ATTENTION For your protection in the event of theft or loss of this product please fill in the information below for you own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased
5. SANYO INSTRUCTION MANUAL VM 6609 VM 6612 VM 6614 B W Video Monitor VM 661 9 6609 9 inch 6612 12 inch 6614 14 inch 6619 19 inch About this manual e Before installing and using this unit please read this manual carefully Be sure to keep it handy for later reference e This manual gives basic connections and operating instructions for 4 models VM 6609 6612 6614 and 6619 INFORMATION TO USER WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS A RISK OF ELECTRIC SHOCK DO NOT OPEN FCC COMPLIANCE STATEMENT CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Explanation of graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the produc s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons FCC INFORMATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
6. ction e The components and connection cables are not included and must be purchased separately 6 BASIC OPERATION 1 Press the POWER switch to turn on the power ON The power is turned on the POWER indicator is lit OFF The power is turned off the POWER indicator is off 2 Select the picture input Use the monitor selector switch at the front of the monitor to select the picture being input to either the A or B input terminal NOTE If there is no input source connected to either the A or B input terminal no picture will appear when that input terminal is selected 3 Adjust the picture Adjusting the picture brightness Turn the BRIGHT control to the left or right to adjust the picture brightness Right The picture becomes brighter Left The picture becomes darker Adjusting the picture contrast Turn the CONTRAST control to the left or right to adjust the picture contrast Right The picture becomes sharper Left The picture becomes softer TROUBLESHOOTING Solutions to common problems related to your monitor are described here If none of the solutions presented here solves the problem unplug the monitor and consult a SANYO authorized dealer or service center for assistance Problems Points to be checked Measures Remedy No power supply Is the power plug loosened or disconnected Firmly insert the power plug No picture with the power on Is the video signal output from the connected c
7. e a damp cloth for cleaning ATTACHMENT Do not use attachments not recommended by the video monitor or equipment manufacturer as they may result in the risk of fire electric shock or injury to persons WATER AND MOISTURE Do not use the video monitor or equipment near water for example near a bathtub washbowIl kitchen sink laundry tub in a wet basement or near a swimming pool or the like ACCESSORIES Do not place video monitor or equipment on an unstable cart stand or table The video monitor or equipment may fall causing serious injury to a child or adult and serious damage to the equipment Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer Video monitor or equipment and cart combinations should be moved with care Quick stops excessive force and uneven surfaces may cause the equipment and cart combination to AN overturn VENTILATION Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the video monitor or equipment and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the video monitor or equipment on a bed sofa rug or other similar surface Video monitor or equipment should never be placed near or over a radiator or heat register Video monitor or equipment receiver should not be
8. eed for service REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original parts Unauthorized substitutions may result in fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine that the video product is in proper operating condition PRECAUTION CONTENTS If an abnormality does occur turn the power switch off and PARTS NAMES cccccccccccccee 4 unplug the unit Have a qualified technician perform any repairs Front Panel iis ee ice een ewes 4 Do not use the monitor if it makes a strange noise emits a strange odor or if smoke comes out from it Rear Panel edichee bik ieatnaeap aes 5 If used under these conditions the monitor may cause a fire or electric shock Immediately unplug it and wait to make sure no CONNECTION 6 40 sande ite gee oe 6 more smoke comes from it Then take it to the dealer for service Do not try to repair or open the monitor yourself Single connection 6 Do not allow the power cord to get damaged Multiple connection 2 2055 6 e Do not place heavy objects on the power cord e Do not place the power cord near a heat source BASIC OPERATION 7 e Do not excessively bend the power cord modify it
9. ls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts batteries or routine maintenance This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED WITH REGARD TO THIS PRODUCT INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS INNO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SFC S LIABILITY FOR ANY AND ALL LOSSES AND DAM
10. o Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 5013 Weekdays 8 30 AM 5 00 PM Pacific Time For accessories and or parts call PARTS ORDER INFORMATION 1 800 726 9662 Weekdays 8 30 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail LABOR PARTS PICTURE TUBE 1 YEARS 1 YEARS 1 YEARS EXCLUSIONS This warranty does not cover A the adjustment of customer operated contro
11. omponent Set the connected component correctly Is the input signal selected properly Select the required video signal input with the Monitor selector switch See page 4 Is the video cable disconnected Connect the video signal cable firmly See page 6 Shaking picture Is the monitor close to a device generating a strong magnetic field Move the device away from the monitor until the picture stabilizes Picture is too bright and hard to view Has the termination switch been set correctly The following are not malfunctions e You experience a mild electric shock when you touch the picture tube This phenomenon is due to a normal buildup of static electricity on the CRT and is not harmful e The monitor emits a strange sound when the room temperature changes suddenly This is only a problem if an abnormality appears on the screen as well e f two or more monitors are operated next each other their images may shake or be distorted This phenomenon is due to mutual interference it is not a malfunction Move the monitors away from each other until the interference disappears or turn the power off on any monitor that is not being used Move the termination switch to the correct setting SPECIFICATIONS VM 6609 VM 6612 VM 6614 VM 6619 System EIA standard Picture tube 9 measured 12 measured 15 measured 20 measured diagonally 90 diagonally 90 diagonally 90 diag
12. onally 90 deflection angle deflection angle deflection angle deflection angle Resolution More than 800 TV lines center More than 1000 TV lines center Horizontal 15 75 kHz EIA Vertical 60 Hz EIA Scanning frequency Input terminals VIDEOA Composite video 1 line BNC connector 1 0 Vp p 75 negative sync VIDEO B Composite video 1 line BNC connector 1 0 Vp p 75 Q negative sync Output terminals VIDEOA Composite video 1 line BNC connector 1 0 Vp p 75 negative sync VIDEO B Composite video 1 line BNC connector 1 0 Vp p 75 negative sync Sub Adjusting control Sub bright volume Yes Yes Yes Vertical size volume Yes Yes Yes Vertical hold volume Yes No Termination switch Manual switchable Hi 75 Q Lo Operating environment Temperature 10 to 40 C Humidity 10 to 90 Power Source AC 100 V 240 V 50 60 Hz Power consumption 20 W 30 W 35 W 36 W Dimensions W x H x D 222 x 238 x 250 mm 304 x 320x310mm_ 350 x 350 x 360 mm_si 472 x 450 x 360 mm Weight 4 5 kg 7 5 kg 11 kg 19 kg Accessory AC power cord x 1 Features and specifications are subject to change without prior notice or obligations Example VM6609 SANYO INDUSTRIAL VIDEO VIDEO MONITOR LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sany
13. or secure it with staples TROUBLES HOOTING eee 8 Doing so may damage the power cord and cause a fire or electric shock SPECIFICATIONS 0000 eeneuuee 9 If the power cord is damaged take it to the dealer and have it replaced Do not allow dust or dirt to build up on the FEATU R ES power cord or power outlet A build up of dust may cause a short circuit or generate heat e Universal power AC 100V to AC 240V and and cause a fire Be especially careful when using the monitor in areas of high humidity in areas with frequent condensation in kitchens and in e 2 Channel Input A B Channel selectable places where there is excessive dust detachable power cord Periodically unplug the power cord and clean away the dust that Contrast Bright control on front panel and builds up between the plug terminals Sub bright V size V hold control on rear panel Cautions when plugging in the power cord e Horizontal resolution e Make sure you insert the plug of the power cord all the way in VM 6609 6612 more than 800 TV line the power outlet Using the monitor with the power cord not VM 6614 6619 more than 1000 TV line fully plugged in may cause heat to generate and cause a fire e Do not use the monitor with the power cord wound or tied up Heat may generate and cause a fire e When using an extension cord be sure that the total current load of all equipment connected to it dose not exceed the specified ratings of the extension cord If
14. placed in a built in installation such as a bookcase unless proper ventilation is provided POWER SOURCES Video monitor or equipment should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your video monitor or equipment dealer or local power company For video monitor or equipment designed to operate from battery power refer to the operating instructions GROUNDING OR POLARIZATION This product is equipped with a three wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug POWER CORDS Do not allow anything to rest on the power cord Do not locate video monitor or equipment where the cord will be abused by persons walking on it HEED WARNINGS Follow all instructions marked on the video monitor or equipment 12 13 14 15 16 17 18 LIGHTNING For added protection for video monitor or equipment during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the video product due to lightning and power line surges
15. set all of the termination switch on the monitors to the HI position However the last monitor termination switch should be in the 75Q position for proper line termination CONNECTION Before connecting your system make sure that all units are turned off The picture signal source can be connected to either the A or B terminal at the rear of the monitor The monitor selector switch at the front of the monitor can be used to select the input terminal used Hi Single Connection To Video B l INPUT terminal Video signal cable OON VIDEO LES Q Monitor To Video A ie INPUT terminal Monitor To Video input terminal Video signal cable Video recorder To Video input terminal KA Video recorder G4 Video camera Note The components and connection cables are not included and must be purchased separately W Multiple Connection Multi connection is possible using the loop through feature of this unit When this monitor is connected to additional monitors the same picture can be obtained on all the connected monitors Set the final monitor to 75 Q termination state cer cerc eee cee Peeerereeceeereeererecerereeereceeee Peeerereeceeereeererecerereereeeee KF Monitor Video recorder Video camera Note e Do not leave a unused cable and do not connect BNC connector to the last jack of the monitor Only once conne
16. st picture brightness according to your requirement Power Indicator Lights when the power is on Lit When the power is on Unlit When power is off Power Switch POWER Press this switch to turn the power on or off B CONTRAST BRIGHT POWER PARTS NAMES Rear Panel VM 6609 VM 6614 Saeed eee V HOLD SUB BRI V SIZE AC INPUT VM 6612 AC input socket AC INPUT Sub brightness control SUB BRI Connect the AC power cord supplied securely to this Turn to adjust picture brightness socket and to a wall outlet Vertical Size control V SIZE 2 Video input terminals VIDEO IN Turn to adjust picture vertical size of the picture These terminals are used to input a video signal Sorat Hie CRIEE 7 Vertical hold control V HOLD Connect to the video output of a VCR or another If the picture is scrolling up or down on the screen monitor for loop through connection or to a video turn this control until there is a single steady picture camera Video output terminals VIDEO OUT These terminals are used to output a video signal from this monitor Loop through output of the video in BNC connector then connect to the video input of another monitor or a VCR Termination Switch HI 75Q Lo Select the input impedance HI 75Q When using only one monitor turn the termination switch to the 75Q position When using more than one monitor
Download Pdf Manuals
Related Search