Sanyo POA-RCKIT03 User's Manual
Contents
1. AVOID EXPLOSURE LASER CAUTION Fom mis arcrrure LASER RADIATION DO NOT STARE INTO THE BEAM WAVE LENGTH 640 660nm MAXIMUM OUTPUT _1mW CLASS I LASER PRODUCT CLASS 2 LASER PRODUCT Complies with 21 CFR 1040 10 AND 1040 11 IEC60825 1 1993 A1 1997 A2 2001 LASER STRAHLING NIGHT IN DEN STRAHL BLICKEN aa MANUFACTURER B CR MANUFACTURED F 3t November 2004 FH E LEDETE cCHEWCE DZALL H Mim JIS C 6802 1998 BAHH 1 OmW RR 640 660nm INTERLINK K K MADE IN CHINA 1 10 7 Higashi Kanda Chiyoda Ku Tokyo Japan 101 0031 Laser Light Window 8 REMOTE CONTROL BATTERY INSTALLATION Remove the battery I compartment lid 2 Slide the batteries into 3 Replace the compartment lid the compartment Two AAA size batteries For correct polarity and be sure battery terminals are in contact with pins in compartment AN Press the lid downward D anid ideit Use 2 AAA SUM 4 or LROS type alkaline batteries Replace two batteries at the same time Do not use a new battery with a used battery Avoid contact with water or liquid Do not expose the remote control to moisture or heat Do not drop the remote control f battery solution has leaked in the battery compartment carefully wipe the compartment clean and install new batteries Risk of explosion if the battery is replaced by an incorrect type Dispose of used batteries according to the instructions i To in2. S LASER POINTER REMOTE CONTROL UNIT MODEL POA RCKIT03 Operating Instruction Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Do not make any changes or modifications to the equipment unless otherwise specified in the instructions If such changes or modifications should be made you could be required to stop operation of the equipment The CE Mark is a Directive Voor de klanten in Neder
3. an extended time remove batteries For cleaning use a soft dry cloth Do not apply benzene thinner splay or any chemical materials DO NOT OPEN AND ATTEMPT TO SERVICE INSIDE OF THE REMOTE CONTROL UNIT THERE ARE NO SERVICEABLE PARTS NAME AND FUNCTION OF EACH BUTTON SIGNAL EMISSION INDICATOR Light red while the laser beam is emitted from the Laser Light Window or the signal is being sent from the remote control unit POWER ON OFF button to the projector Turn the projector on or off COMPUTER button VIDEO button Select the input source COM Select the input PUTER VIDEO O AUTO PC button D ZOOM buttons KEYSTONE AUTO PC Operate the Auto PC adjust Select the Digital zoom _ ment function mode and resize the image C KEYSTONE button Correct keystone distortion gt POINT VOLUME Y buttons Select an item or adjust the value in the On Screen Menu These are also used to pan the image in the Digital zoom mode The POINT lt P buttons are also used as the VOLUME buttons LASER button Operate the Laser pointer function The Laser beam is emitted while pressing this button within 1 minute When using this laser pointer for more than 1 minute release the LASER button and press it again source Execute the item selected or expand or compress the image in the Digital zoom mode Open or close the On Screen Menu Freeze t
4. he projected picture PAGE buttons Turn page the Up button to the previous page and the Down button to the next page for an image from a computer Connect the projector and your computer with a USB cable before use P TIMER button Operate the P Timer func tion Select image levels NO SHOW button Turn the picture into black image Mute the sound Note For detailed operation refer to the projector owner s manual LASER POINTER FUNCTION C This remote control emits a laser beam from the Laser Light Window With the LASER button pressed the laser light goes on The signal emission indicator lights red and the laser is emitted with red light With the LASER button pressed for more than 1 minute or released the light goes off To lock this function press both the MENU button and the NO SHOW button for more than 10 seconds To unlock press the MENU button and NO SHOW button again for more than 10 seconds The laser emitted is a class I laser Do not look into the laser light window or shine the laser beam on yourself or other people The caution labels for laser beam are shown below CAUTION Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Do not look into the Laser Light Window while the laser is emitted otherwise eye damage may result The caution label is put on the remote control Signal Emission Indicator
5. land conformity mark of the European Bij dit produkt zijn batterijen geleverd Community EC Wanneer deze leeg zijn moet u ze niet weggooien maar inleveren als KCA O 2 oO as IL Italiano FEATURES Laser Pointer This Remote Control Unit provides the Laser Pointer function This function helps you to make a smart presentation on a projected screen Remote Control Code This Remote Control Unit has 2 different remote control codes the factory set normal code Code 1 and the secondary code Code 2 This switching function prevents remote control operation mixture jam when operating several projectors To change the code of the Remote Control Unit press both the MENU and the IMAGE buttons together for over 10 seconds When batteries of the the Remote Control Unit are replaced the remote control code automatically returns to the normal code Code 1 Refer to the Owner s Manual of your projector for switching the code of the projector N SAFETY PRECAUTIONS Before operation read this Instruction Manual thoroughly to operate properly This Remote Control Unit emits laser beam from the Laser Light Window while pressing the LASER button for 1 minute The Signal Emission Indicator lights red to indicate the laser emission Do not look into the Laser Light Window or shine laser beam on yourself or the other people Eye damage may result f this Remote Control Unit is not to be used for
6. sure safe operation please observe the following precautions TECHNICAL SPECIFICATIONS Power Source AAA SUM 4 or LRO3 Type x 2 Operating Range 16 4 5m 30 Dimensions 1 8 x 1 0 x 5 7 45mm x 25mm x 145mm Net Weight 0 22 Ibs 99 g including batteries Laser Pointer Class II Laser Max Output 1m W Wave length 640 660nm Specifications are subject to change without notice
Download Pdf Manuals
Related Search