Samsung SCC-B5343 User's Manual
Contents
1. the camera viewing angle You can rotate your camera leftward or rightward Panning and can change the slope gt ea of your camera upward or downward Tilting In case of panning the rotation limit of your camera is TE er set to 355 degree 100 degree clockwise and 255 degree 7 di y inside of the camera For panning control first unfasten two screws located on the bottom and rotate in the direction you want and then fasten them to fix the camera Tilt can be adjusted between 0 to 90 however tilt angles of less than 20 may result in a partial blind spot depending on your lens configuration To fix the location after adjusting the tilting angle use the Tilt fixing screws counterclockwise The rotation is stopped by the Stopper Tilting Lens rotation To adjust the focus and zoom of your camera use the Zoom lever and Focus lever When you install the camera on the inclined ceiling or wall you can rotate the camera lens to see a correct direction image 12 SCC B5342 B5343 SNS Appendix A Specifications for NTSC Standard Item Details Product type CCTV color dome camera Power input AC 24V 10 60Hz 0 3 Hz DC 12V 10 5 Broadcast type NTSC Standard System 525 Lines 60 Fields Power consumption Approx 1 7W Image device 1 3 inch IT Type Super HAD CCD Pixels Total2. 49 F or high humidity Doing so may cause fire or electric shock f you want to relocate the already installed product be sure to turn off the power and then move or reinstall it Remove the power plug from the outlet when there is a lighting storm Neglecting o do so may cause fire or damage to he product Keep out of direct sunlight and heat radiation sources It may cause fire nstall it in a place with good ventilation Avoid aiming the camera directly towards extremely bright objects such as sun as this may damage the CCD image sensor Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus The Mains plug is used as a disconnect device and shall stay readily operable at any time FCC Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if
3. 811 H x 508 V 410 000 pixels Effective 768 H x 494 V 380 000 pixels Scanning mode 525 Lines 2 1 Interlace Scanning line frequency Horizontal 15 734Hz INT 15 750Hz LL Vertical 59 94Hz INT 60Hz LL Synchronization mode INT Line Lock Adjusting the phase using INC DEC button Horizontal resolution 540 TV Lines S N Ratio Min object illumination Approx 50dB SCC B5343 Color BW SCC B5342 Color BW SOIRE 0 4 0 04Lux 0 4 0 4Lux Sens up Off 30IRE 0 24 0 024Lux 0 24 0 24Lux F12 15IRE 0 12 0 012Lux 0 12 0 12Lux SOIRE 0 0031 0 00031Lux 0 0031 0 0031Lux Sens up x128 30IRE 0 0019 0 00019Lux 0 0019 0 0019Lux 15IRE 0 0009 0 00009Lux 0 0009 0 0009Lux Signal output COMPOSITE Video 1 0 Vp p 750hm BNC Test Monitor OUT 1 0 Vp p 750hm Harness cable Lens Auto Iris DC Focal length 2 5 to 6 0mm Aperture ratio 1 2 PAN function Range 0 to 355 100 degree clockwise and 255 degree counterclockwise TILT function Range 0 to 90 Line Lock LL Sens Up Low Speed Shutter LSS Horizontal Reverse H REV Vertical Reverse V REV Controls Backlight compensation BLC Flickerless FL Switching between color and B amp W modes D N Auto white balancing AWB Digital noise reduction DNR Dynamic CCD defect compensation Product color SCC B5342N B5343N White Operation temperature 10 C to 50 C Operation humidity
4. BNC cable and Power connector to power adapter 11 Video connector Power connector Installation I Setting switches Setting function switches To set the available functions on your camera adjust eight switches as shown below Name Brief description EL Line lock ON OFF LSS Sens up or Low speed shutter ON OFF H REV Horizontal reverse ON OFF V REV Vertical reverse ON OFF BLC Backlight compensation ON OFF FL Flickerless ON OFF DIN Automatic switching between color and black amp white ON OFF AWB Automatic white balance ON OFF 1 Switch 1 LL When this switch is set to OFF the camera operates in the internal synchronization mode while when it is set to ON the camera operates in the line lock mode In the internal synchronization mode the camera always uses an inside crystal oscillator for synchronization However if multiple cameras are connected to a sequential switcher picture rolling or flickering may occur when switching from one camera to another In this case you can set this switch to ON to solve this problem The line lock mode allows the camera to use the phase of the AC power as the synchronization reference In this mode you can use the phase control buttons INC DEC When you are using the DC 12V power set this switch to OFF The line lock feature will not normally operate even when the switch is set to ON Set the LL switch to ON wh
5. Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket 13 14 or table specified by the manufacturer or sold with the apparatus O Unplug this apparatus when a card is used Use caution when moving the cart apparatus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus shall not be exposed to N dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Overview 6 About this guide Product overview Main features Components Checking components in the package Components of your camera Installation Setting switches Setting function switches Connecting cables and changing the settings Installing camera Before installation Installation procedure Adjusting the camera direction Appendix A Specifications for NTSC Standard 14 Appendix B Specifications for PAL Standard 15 SNS Overview I About this guide This user guide includes basic instructions for the product It is recom
6. Up to 90 Size 128 x 91 H mm Weight 3279 14 Appendix B Specifications for PAL Standard Item Details Product type CCTV color dome camera Power input AC 24V 10 50Hz 0 3 Hz DC 12V 10 5 Broadcast type PAL Standard System 625 Lines 50 Fields Power consumption Approx 1 7W Image device 1 3 inch IT Type Super HAD CCD Pixels Total 795 H x 596 V 470 000 pixels Effective 752 H x 582 V 440 000 pixels Scanning mode 625 Lines 2 1 Interlace Scanning line frequency Horizontal 15 625Hz INT 15 625Hz LL Vertical 50Hz INT 50Hz LL Synchronization mode INT Line Lock Adjusting the phase using INC DEC button Horizontal resolution 540 TV Lines SIN Ratio Min object illumination Approx 50dB SCC B5343 Color BW SCC B5342 Color BW F12 SOIRE 0 4 0 04Lux 0 4 0 4Lux Sens up Off 30IRE 0 24 0 024Lux 0 24 0 24Lux 15IRE 0 12 0 012Lux 0 12 0 12Lux SOIRE 0 0031 0 00031Lux 0 0031 0 0031Lux Sens up x128 30IRE 0 0019 0 00019Lux 0 0019 0 0019Lux 15IRE 0 0009 0 00009Lux 0 0009 0 0009Lux Signal output COMPOSITE Video 1 0 Vp p 750hm BNC Test Monitor OUT 1 0 Vp p 750hm Harness cable Lens Auto Iris DC Focal length 2 5 to 6 0mm Aperture ratio 1 2 PAN function Range 0 to 355 100 degree clockwise and 255 degree counterclockwise TILT function Range 0 to 90 Line Lock LL Sens Up Low S
7. not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IC Compliance Notice IR This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 IMPORTANT SAFETY INSTRUCTIONS NOaPoON gt 10 11 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus
8. SCC B5342 x SCC B5343 Digital Color operating instructions vu imagine the possibilities E Thank you for purchasing this Samsung product To receive more complete service please register your product at ea www samsung com global register EXPLANATION OF SAFETY RELATED SYMBOLS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL i This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit This symbol indicates that there are N important operating and maintenance instructions in the literature accompanying this unit WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture To prevent injury this apparatus must be securely attached to the floor wall in accordance with the installation instructions If this power supply is used at 240V ac a suitable plug adapter should be used WARNING Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to the product 3 Do not connect multiple camer
9. as to a single adapter Exceeding the capacity may cause abnormal heat generation or fire Securely plug the power cord into the power receptacle Insecure connection May cause fire When installing the camera fasten it securely and firmly The fall of camera May cause personal injury Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the camera Doing so may cause personal injury due to fire electric shock or falling objects Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION 1 Do not drop objects on the product or apply strong blows to it Keep away from a location subject to excessive vibration or magnetic interference Do not install in a location subject to high temperature over 140 F low emperature below
10. g to a portable display If you really want to connect the camera to a monitoring display use the BNC cable Components of your camera Your camera has the following components a Cover dome Covers the main body for protection Main body Includes a lens a switch board a PCB board screws and such Mount bracket Used as a ceiling or wall fixture It is fixed using three long tab screws provided in the package O Cable Stopper If drawing the cable from a hole in the ceiling remove this stopper and pass the cable through the opening to connect Zoom lever Using this lever the lens zoom can be adjusted and fixed 0 Focus lever The lens focus can be adjusted by rotating it left or right Rotate it clockwise for fixing Tilt fixing screw Using this screw the slope of the Lens lens can e adjusted and fixed Switch board Includes two kinds of control switches such as function switches and phase control switches The board has eight function switches in the middle and two phase control buttons on each side of the function switch area O Installation Guide Mark This mark must be aligned with the marking on the bracket when attaching the camera to the bracket Lock releaser Push it outward and rotate the main body in UNLOCK direction when you want to remove the Mount bracket from the Main body or to remove the installed camera from the Mount bracket Cable Connect the Video connector to
11. ge appears 1 Remove the Cover dome and Inner cover For more details about the removing procedures see Installation procedure in the Installing camera section on the next page 2 Adjust the focus zoom and function settings of your camera using the Focus lever Zoom lever and Switch board while you are viewing the image on the screen 3 If you want to fix the adjusted focus and zoom screw up the levers 10 I Installing camera Before installation Before installing your camera you have to read the following cautions You have to check whether the location ceiling or wall can bear five times the weight of your camera Don t let the cable to be caught in improper place or the electric line cover to be damaged Otherwise it may cause a breakdown or fire When installing your camera don t allow any person to approach the installation site If you have any valuable things under the place move them away Partial blind spot can occur at tilt angles of less than 20 depending on the lens configuration Installation procedure To install your camera O Pry up the outer casing with a flat head screwdriver to remove the protective cover from the Main body of the camera Remove the Mount bracket from the Main body by rotating the Main body in the UNLOCK direction while pushing the Lock releaser outward If it is not easily done rotate the Mount bracket in the LOCK direction while holding small holes on the Moun
12. ile the AC power is connected If any picture roll happens you have to adjust the phase using the phase control buttons Press the INC or DEC button to increase or decrease the phase by one degree Switch 2 LSS This sens up mode accumulates the image fields in memory to reduce noise but increase the brightness and contrast rate When this switch is set to ON the camera automatically switches to a maximum of 128 times of image acquisition speed to implement a clear picture for darker image Switch 3 H REV When this switch is set to ON the camera image is reversed horizontally If you want to monitor your site using a mirror you can use this feature to see the right image Switch 4 V REV When this switch is set to ON the camera image is reversed vertically If your camera reluctantly displays the vertically reversed image you can use this feature to see the right image Switch 5 BLC When this switch is set to ON you can view a clear image even though the camera faces any excessive light such as sunlight and fluorescent light When it is set to OFF the subject with excessive light is not clearly shown Switch 6 FL When this switch is set to ON the shutter speed is fixed to 1 100 sec for NTSC or 1 120 sec for PAL to prevent screen from flickering by the disaccordance between vertical synchronous frequency 50Hz for NTSC 60Hz for PAL and on and off frequency of a light Switch 7 D N When this sw
13. itch is set to ON the camera automatically switches between color and B amp W according to the brightness of the vicinity Switch 8 AWB This switch adjusts white balancing When this switch is set to ON this camera operates in ATW mode and in case of OFF this camera operates in AWC mode ATW Auto Tracking White Balance The color temperature is automatically adjusted according to the environmental change Approx 2000 K to 11 000 K AWC Auto White Balance Control It stores the color temperature just when the switch is changed to OFF Accordingly color temperatures are adjusted by the stored value The IRIS setting range for the camera is approximately 80 to 120 IRE It means the camera does not provide the IRIS full open close feature but the restricted variation range Use the camera after setting to the proper level 80 IRE or above because the IRIS hunting may occur when the level is 75 IRE or below I Connecting cables and changing the settings Before installing your camera you have to adjust the lens focus zoom and switch settings L BNC Cable To adjust the lens focus zoom and function settings Monitor To connect cables 1 Connect the BNC cable to the Video connector attached on your camera Connect the BNC cable to the Video Input on a monitor Connect the power adapter to the Power connector attached on your camera When the monitor is turned on the camera ima
14. mended that all users read this guide before use Tus guide is divided as follows Chapter 1 Overview introduces the user guide and product related information This chapter Chapter 2 Installation explains how to set and install the product m Appendix Specifications provides the specifications of the product I Product overview This is the high resolution 540 TV lines dome camera equipped with a Vari focal lens which has no dynamic delay when implementing motion pictures and provides the features such as digital noise reduction DNR by real time CCD defect compensation low speed shutter LSS Auto x128 to implement clear picture quality Day Night color compensation and the like I Main features m Power DC 12V AC 24V Special functions Line lock LL control Auto white balancing Horizontal vertical image reversing Flickerless control Low shutter speed control Backlight compensation control Automatic switching between color and black amp white modes Equipped with vari focal lens Auto Iris function Digital noise reduction DNR Dynamic CCD defect compensation I Components Checking components in the package Please check your camera and accessories are included in the package Those components are as shown below OS oS Camera Test Monitor Cable ES ob Tab screw User s Guide The test monitor cable is used to test the camera by connectin
15. peed Shutter LSS Horizontal Reverse H REV Vertical Reverse V REV Controls Backlight compensation BLC Flickerless FL Switching between color and B amp W modes D N Auto white balancing AWB Digital noise reduction DNR Dynamic CCD defect compensation Product color SCC B5342P B5343P White Operation temperature 10 C to 50 C Operation humidity Up to 90 Size 128 9 x 91 H mm Weight 3279 15 I Memo
16. t bracket Fix the Mount bracket to the location ceiling or wall with supplied three screws The CAMERA FRONT sign on the Mount bracket should face the camera monitoring area Ceiling mount opener 11 O If a hole has been drilled on the bracket installation surface for cable access press down to remove the Cable Stopper and then draw the cable in If connecting through the side of the camera use the empty space opposite to the side marked CAMERA FRONT Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning the Groove mark on the Main body with the wide groove around the CAMERA FRONT inlay Adjust the camera direction For more details on the direction control see Adjusting the camera direction on the same page When required to adjust the zoom and focus for your camera see Connecting cables and changing the settings on page 10 Attach the Inner cover to the Main body by pressing it until a click sound is heard after aligning two screw holes on the Wing lockers of the Inner cover with two screw holes on the Main body s left and right sides O Finally attach the Cover dome to the Main body by pressing it until a click sound is heard after aligning the bump inside the Cover dome with the Groove mark on the Main body I Adjusting the camera direction When the camera is fixed on the ceiling you can adjust Panning
Download Pdf Manuals
Related Search