Home

Samsung S27B970D User's Manual

1. Personal injury or damage to properties may result if instructions are not Caution ING ia ab 7 followed S Activities marked by this symbol are prohibited Instructions marked by this symbol must be followed Precautions for storage High glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product Service fee will be charged Before Using the Product The following images are for reference only Real life situations may differ from what is shown in the images Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched Take the following steps when cleaning 1 Power off the product 2 Remove the power cable from the product Hold the power cable by the plug and do not touch the cable with wet hands Otherwise an electric shock may result 3 Wipe the product screen using a clean soft and dry cloth Do not use detergents that contain alcohol solvent or surface active agents Do not spray water or detergent directly on the product 4 To clean the exterior of the product use a moist soft cloth and wring thoroughly before wiping the exterior 5 After cleaning the product connect the power cable to the product 6 Power on the product to use it Electricity and Safety T
2. About ports CG USB USB Connect to a source device using a USB cable Source devices can be charged using these USB ports Adjusting the Product Tilt The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality e You can adjust the product tilt e To avoid damage to the product when adjusting the tilt push or pull the top area of the product at the center while holding the top of the stand 17 Preparation The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality e You can adjust the product height e To avoid damage to the product hold the middle of the left and right hand sides of the product when adjusting the tilt 18 Chapter 3 Using NCE Natural Color Expert Configure the screen settings such as brightness and color tone Compatible Types of Calibrators What is Monitor Calibration ST i1Pro series i1Display Pro ColorMunki Photo Most of digital images are managed onscreen That is why a monitor is very important for photographers and designers The process to calibrate a monitor in order to display proper Manufacturer xrite xrite xrite colors is called monitor calibration i1Photo Pro UV This product went through a calibration process using color measurement equipment in the nae PORO PURA Color
3. S27B970D User manual The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance BN46 00252A 03 Table of Contents Chapter 1 BEFORE USING THE PRODUCT 5 Copyright 6 Securing the Installation Space 6 Safety Precautions 6 Symbols 7 Cleaning 7 Electricity and Safety 8 Installation and Safety 9 Operation and Safety 12 Correct posture to use the product Chapter 2 PREPARATION 13 Checking the Contents 13 Removing the Packaging 14 Checking the Components 15 Parts 15 Front Buttons 16 Rear View 17 Side View 17 Adjusting the Product Tilt 18 Adjusting the Product Height Chapter 3 USING NCE NATURAL COLOR EXPERT 19 What is Monitor Calibration 19 Compatible Types of Calibrators 20 What is NCE Natural Color Expert 20 NCE Program Installation Uninstallation 21 Starting NCE Natural Color Expert 21 Connecting the Calibrator 21 Features of the NCE Program 21 Layout and Menu Items on the NCE Home Screen 22 Profile List 22 Layout and Menu Items on the Preference Screen 23 Layout and Menu Items on the Uniformity Screen 23 Layout and Menu Items on the Edit Screen 24 Layout and Menu Items on the Calibration Screen 24 Layout and Menu Items on the New Profile Screen 27 Preparing for Calibration 27 Completing Calibration Chapter 4 USING MHL 28 MHL Mobile High Definition Lin
4. 4 Installation progress will be displayed 5 Click Finish in the displayed InstallShield Wizard Complete screen 6 The Natural Color Expert v2 shortcut icon will be created on the desktop after installation e The Natural Color Expert v2 execution icon may not be displayed depending on the PC system or product specifications e Press the F5 key Refresh if the execution icon does not appear Uninstallation 1 Go to Settings Control Panel on the Start menu and double click Add or Remove Programs 2 Select Natural Color Expert v2 from the list and click Change Remove Natural Color Expert v2 installation can be affected by the graphics card mother board and network conditions 20 Using NCE Natural Color Expert Starting NCE Natural Color Expert Connecting the Calibrator 1 Connect the PC IN port on the product to a USB port on the PC using the USB cable 2 Connect the calibrator to a USB port on the product Install the driver which is usually provided with a calibration program provided by the calibrator manufacturer first before connecting the calibrator 3 The connected calibrator will automatically appear in the Select a Calibrator screen If more than one calibrator is connected select the desired calibrator in the Select a Calibrator screen Next click Next Features of the NCE Program Layout and Menu Items on the NCE Home Screen
5. Stl SAMSUNG monitor installer Select the monitor which you want to install Samsung 5 Go to Display Properties and check that the resolution and refresh rate are appropriate Refer to your Windows OS manual for further details 33 Connecting and Using a Source Device Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase Select a language and change the resolution to the optimum value The optimal resolution for this monitor is as follows Follow the above settings to set the resolution English v Enter 1 Press q A W to move to the language you want and press T 2 To hide the information message press O0 If the optimal resolution is not selected the message will appear up to three times for a specified time even after the product is turned off and on again The resolution can also be changed to the optimal setting 1920 x 1080 using Control Panel on your PC Changing the Resolution Using a PC Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality The picture quality of TFT LCDs may degrade if the optimum resolution is not selected Changing the Resolution on Windows XP Go to Control Panel Display Settings and change the resolution 34 Connecting and Using a Source Device Changing the Resolution
6. Adjust the COLOR settings The product is operating in power saving mode Press any key on the keyboard or move the mouse to return to normal operating mode Audio issues There is no sound The volume is too low Solutions Adjust the product volume Check that the source device connected to the product is powered on Adjust the volume If the volume is still low after turning it up to the maximum level adjust the volume on your PC sound card or software program Source device issue A beeping sound is heard continuously when my PC is booting Other issues The stand generates heat Why is that Does this mean that the product is defective Solutions Have your PC serviced if it makes a beeping sound when booting Solutions The upper part of the stand may become slightly hot at room temperature This occurs as the heat inside the stand releases naturally The intensity of heat you feel can vary depending on whether the room is sealed or depending on the surrounding temperature This does not indicate a defect You can use the product without worry It is recommended to use the product in a location that offers good ventilation at the back of the monitor stand 55 Troubleshooting Guide Q amp A Set the frequency on your graphics card How can I change the frequency How can I change the resolution Windows XP Go to Control Panel gt Appearance and Themes Display Setting
7. Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC e Windows 7 Set power saving mode in Control Panel gt Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Refer to the user manual for your PC or graphics card for further instructions on adjustment 56 Chapter 12 Specifications 645 0 x 467 0 x 247 0 mm 7 9 kg Dimensions W x H x D Weight 25 4 x 18 4 x 9 7 inches 17 4 Ibs Temperature 50 F 104 F 10 C 40 C Humidity 10 Yo 80 non condensing Size 27 inches 69 cm Sone Temperature 4 F 113 F 20 C 45 C Panel 596 74 mm H x 335 66 mm V Storage KA i Display area Humidity 5 95 non condensing 23 49 inches H x 13 21 inches V a Due to the nature of the manufacturing of this orizonta bing Frequency 30 81 kHz Panel Dais ries product approximately 1 pixel per million ee may Synchronization be brighter or darker on the LCD panel This does not Vertical a affect product performance Peeni 24 60 Hz 24 Hz 30 Hz MHL Display Color 16 7 M The above specifications are subject to change without notice to improve quality Opinu ET This device is a Class B digital apparatus Resolution Resolution USA Only Maximum Resolution 2560 x 1440 Dispose unwanted electronics through an approved recycler To find the nearest recycling location go to our website Maximum Pixel Cl
8. Q V buttons Next press the T button 5 The selected option will be applied 50 Setup and Reset Off Timer Setting The off timer can be set within a range of 1 to 23 hours The product will automatically power off after the specified number of hours Available only when Off Timer On Off is set to On Configuring Off Timer Setting 1 Press D on the product 2 Move to SETUP amp RESET using the 0 A Q V buttons Next press the Z737 button 3 Move to Off Timer Setting using the A amp W buttons Next press the E button The following screen will appear lt gt Adjust Et Enter 4 Configure the Off Timer Setting using the 0 A 2 V buttons Reset Return all the settings for the product to the default factory settings Restoring the default settings Reset 1 Press M0 on the product 2 Move to SETUP amp RESET using the A amp buttons Next press the FE button 3 Move to Reset using the A Q V buttons Next press the F2 button The following screen will appear Reset all settings No Adjust IE Enter 4 Move to the desired option using the A Q V buttons Next press the F3 button 5 The selected option will be applied 51 Chapter 10 INFORMATION Menu and Others INFORMATION View the current input source frequency and resolution Viewing information INFORMATION 1 Press 1 on the product 2
9. 6686 O O O GO Profile List Home NCE Profile List if ROTO SAAD 190 S002 Yer BOOK LUT 20KG SOTO ARGU 109 906 _2 Poesi BSOP 22 20820990 SEON JANU 200 COC 0 Dpr ODII 2 FOTOS TRONO AAGE 200 100 0 Mer OOK 1 soxense 58970 3ROB 200 108 O 7e 6bat R070 SACA 43 BoI A330 SEGO IAGE 49 90905300 10001 Profile Information Skipped Sumur 4 Change the custom settings for the NCE program Measure the current settings COLOR Uniformity of the monitor SB970 Perform calibration for Uniformity to optimize the display uniformity of the monitor SB970 Create a profile using the option New if a profile for the target settings is not found in the NCE Profile List Also calibrate the monitor SB970 and save the changed color settings after calibration to the NCE Profile List Select a profile from the NCE Profile List to modify the target settings as desired and perform calibration according to the modified settings Select a profile from the NCE Profile List and perform calibration according to the settings of the selected profile Close the program A profile of settings changed after calibration has been saved to the NCE Profile List as shown 21 Using NCE Natural Color Expert Profile List ae T Layout and Menu Items on the Preference This screen shows the current color settings on the monitor Screen Files in the NCE Profile List are monitor profiles saved in
10. A Q V buttons Next press the FE button 3 Move to PC AV Mode using the 0 A Q V buttons Next press the f button The following screen will appear TE Enter 4 Move to the desired option using the 2 A Q V buttons Next press the F3 button 5 The selected option will be applied 48 Setup and Reset Auto Source Enable disable Auto Source mode that detects the input source automatically Configuring Auto Source 1 Press 00 on the product 2 Move to SETUP amp RESET using the A Q V buttons Next press the F3 button 3 Move to Auto Source using the 0 A Q V buttons Next press the Z7 button The following screen will appear EF Enter e Auto Automatically detect the input source e Manual Manually select an input source 4 Move to the desired option using the t A Q V buttons Next press the E button 5 The selected option will be applied Display Time Set the on screen display OSD menu to automatically disappear if the menu is not used for a specified period of time Display Time can be used to set the time after which you want the OSD menu to disappear automatically Configuring Display Time 1 Press M0 on the product 2 Move to SETUP amp RESET using the q A amp W buttons Next press the if button 3 Move to Display Time using the 0 A amp W buttons Next press the T button The follo
11. Ba button to change the input source 15 Preparation OQ A Description Move up to another menu item or adjust a setting when the OSD menu is displayed When no OSD menu is displayed the 1d A buttons can be used to adjust the Volume Brightness or Contrast e The Volume can be adjusted if the input source is DisplayPort or HDMI e The Brightness or Contrast can be adjusted if the input source is DVI e For further details on the Volume Brightness or Contrast go to the section INFORMATION Menu and Others and refer to Configuring Volume in the Initial Screen or Configuring Brightness and Contrast in the Initial Screen Rear View The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality DVI IN HDMI IN MHL DC 14V HDMI IN PC IN DPIN DMIIN DG 14v About ports Connect to a PC using a USB cable This port can connect to a PC only Connects to a PC using a DP cable Connects to a PC via a DVI cable Connect to a PC or source device using an HDMI cable Connect to a source device that has the MHL function using the HDMI MHL cable Connect to a DC power adapter 16 Preparation Side View The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality
12. Custom High Bright Increase the brightness more than when in Cinema and sRGB modes Cinema This mode is suitable to view entertainment content video DVD etc providing a bright and sharp picture sRGB Change the color system to sRGB mode Calibration This mode analyzes the color characteristics of your monitor and allows you to save color information of the monitor as an ICC profile This will tell your monitor what color space it should use and how it should interpret and display colors Optimized color from the Natural Color Expert program and Calibration will be displayed on the screen e When Color Mode is set to Calibration all the options of the color settings menu will be disabled 4 Move to the desired option using the 0 A amp W buttons Next press the i button 5 The selected option will be applied 40 Configuring the Tint Settings Red Green Adjust the value of the color red in the picture Range 0 100 Adjust the value of the color green in the picture Range 0 100 A higher value will increase the intensity of the color A higher value will increase the intensity of the color Configuring Red Configuring Green 1 Press 0 on the product 1 Press M0 on the product 2 Move to COLOR using the q A W buttons Next press the button 2 Move to COLOR using the d A 2 W buttons Next press the IE button 3 Move to Red using the 0 A 2 vV buttons Next press the
13. HDMI port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC 3 Press the F button on the product to change the input source to HDMI MHL e Open the SETUP amp RESET menu Next set PC AV Mode to PC 3 Connecting and Using a Source Device Connection using a Dual link DVI cable digital type Connection Using the DP Cable 1 Connect the DVI cable to the DVI IN port on the back of the product and the DVI port on 1 Connect the DP cable to the DP IN port on the back of the product and the DP port on the PC the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC power switch on the PC 3 Press the E button on the product to change the input source to DVI 3 Press T to change the input source to DisplayPort NOTE NOTE e Open the SETUP amp RESET menu Next set PC AV Mode to PC e Open the SETUP amp RESET menu Next set PC AV Mode to PC e Audio is not available if the PC and product are connected via the DVI port 32 Connecting and Using a Source Device Connecting the Product to a PC as a USB HUB The product can function as a HUB by connecting to a PC via a USB cable You can connect a source device directly to the product and control
14. This product contains a power circuit unit causing the stand to generate heat The heat does not mean the product is defective Description Turn the power on or off The power indicator will be lit when the product is operating normally e For details on the power saving function refer to Power saving Function in the product specifications e To reduce power consumption it is best to remove the power cable when not using the product for an extended period of time This button can be used to display exit from the OSD menu The button can also be used to go back to the previous menu To lock the OSD control press and hold the O button for 10 seconds To unlock the OSD control press and hold the O button for more than 10 seconds If the OSD control is locked e Brightness Contrast Image Size can be adjusted and INFORMATION can be viewed Move down to another menu item or adjust a setting when the OSD menu is displayed Configure the Color Mode using the e V buttons when no OSD menu is displayed e For further details on Color Mode refer to Configuring Color Mode in the section Configuring the Tint Settings Confirm a menu selection Pressing the button when no OSD menu is displayed will change the input source DVI HDMI MHL DisplayPort A message that shows the current input source will appear at the top left corner of the screen each time you turn on the power or press the
15. a location with good ventilation Looking at the screen too close for an extended period of time can deteriorate your eyesight Do not hold the product upside down or move it by holding the stand The product may fall and break or cause a personal injury Do not use humidifiers or stoves around the product A fire or electric shock may result Rest your eyes for more than 5 minutes for every 1 hour of product use Eye fatigue will be relieved Do not touch the screen when the product has been turned on for an extended period of time as it will become hot 11 Before Using the Product Store small accessories out of the reach of children Oe rrect postu re to use the prod T ct Use the product in the correct posture as follows e Straighten your back e Allow a distance of 45 to 50cm between your eye and the screen and look slightly downward at the screen Keep your eyes directly in front of the screen e Adjust the angle so light does not reflect on the screen e Keep your forearms perpendicular to your upper arms and level with the back of your hands e Keep your elbows at about a right angle e Adjust the height of the product so you can keep your knees bent at 90 degrees or more your heels attached to the floor and your arms lower than your heart Do not place heavy objects on the product Product failure or personal injury may result Chapter 2 Preparation Checki ng the Co nte nts 2 Rem
16. and view videos and photos saved on the device using the product screen HDMI IN MHL SAMSUNG 1 Connect the HDMI IN MHL port on the product to the Micro USB port on the mobile device using the mobile cable 2 Connect the DC power adapter to the product and a power socket NOTE e To use the MHL function you need an MHL certified mobile device You can check if your mobile device 3 After the power is connected the product will automatically detect and change the input is MHL certified on the website of the device manufacturer To find a list of MHL certified devices visit SOUNGE the official MHL website http www mhlconsortium org If the input source is not set to HDMI MHL press the button to change the input e To use the MHL function the latest version of software must be installed on the mobile device source e On some mobile devices the MHL function may not be available depending on the device performance or functionality e Since the display size of the product is larger than those of mobile devices the picture quality may degrade e This product is officially MHL certified In the event of a problem with a mobile device connection contact the mobile device manufacturer e The picture quality may degrade when content imported from the mobile device with a low resolution is displayed on the product Tf the screen is blank in HDMI MHL mode power the pro
17. com ch_fr French http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com 61 Appendix RUSSIA 8 800 555 55 55 http www samsung com AUSTRALIA 1300 362 603 http www samsung com GEORGIA 8 800 555 555 http www samsung com NEW ZEALAND 0800 SAMSUNG 0800 726 786 http www samsung com ARMENIA 0 800 05 555 http www samsung com CHINA 400 810 5858 http www samsung com AZERBAIJAN 088 55 55 555 http www samsung com http www samsung com hk HONG KON 2 4698 http k i 3 10 800 500 55 500 ONG KONG 852 3698 p www samsung com KAZAKHSTAN http www samsung com hk_en GSM 7799 1800 1100 11 UZBEKISTAN 8 10 800 500 55 500 http www samsung com 3030 8282 INDIA 1800 3000 8282 http www samsung com KYRGYZSTAN 00 800 500 55 500 http www samsung com 1800 266 8282 10 800 500 55 http i TADJIKISTAN 8 10 800 500 55 500 ttp www samsung com TPE 0800 112 8888 ANA MONGOLIA http www samsung com 021 5699 7777 i i http www samsung com ua JAPAN 0120 327 527 http www samsung com UKRAINE 0 800 502 000 k http www samsung com ua ru MALAYSIA 1800 88 9999 http www samsung com BELARUS 810 800 500 55 500 http www samsung com 1 800 10 SAMSUNG 726 7864 for PLDT MOLDOVA 00 800 500 55 500 http www samsung com p g 1 800 3 SAMSUNG 726 7864 PHILIPPINES for Digitel http www samsung com 1 800 8 SAMSUNG 726 7864 for Globe 02 5805777 SIN
18. contact Samsung Customer Service Center Product failure an electric shock or fire may result 10 Before Using the Product Caution go Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn in or defective pixels If you are not going to use the product for an extended period of time activate power saving mode or a moving picture screen saver Disconnect the power cable from the power socket when not using the product for an extended period of time vacation etc Dust accumulation combined with heat can cause a fire electric shock or electric leakage Use the product at the recommended resolution and frequency Your eyesight may deteriorate Do not put DC power adapters together Otherwise a fire may result Remove the plastic bag from the DC power adapter before you use it Otherwise a fire may result Do not let water enter the DC power adapter or get the adapter wet An electric shock or fire may result Avoid using the product outdoors where it can be exposed to rain or snow Take extra care to ensure the DC power adapter does not get wet when cleaning the floor with water 4 F _e Do not leave the DC power adapter near a heat source Otherwise a fire may result Keep the DC power adapter in
19. i button 3 Move to Green using the 0 A amp W buttons Next press the E button The following screen will appear The following screen will appear lt gt Adjust E Enter lt gt Adjust Enter 4 Adjust the Red setting using the 0 A amp W buttons 4 Adjust the Green setting using the A e V buttons 41 Configuring the Tint Settings Blue Adjust the value of the color blue in the picture Range 0 100 A higher value will increase the intensity of the color Configuring Blue 1 Press 00 on the product 2 Move to COLOR using the q A amp V buttons Next press the T button 3 Move to Blue using the q A amp w buttons Next press the i button The following screen will appear lt gt Adjust IF Enter 4 Adjust the Blue setting using the t A Q V buttons Color Temp Configuring Color Temp 1 Press M0 on the product 2 Move to COLOR using the A W buttons Next press the IT button 3 Press 0 A g W to move to Color Temp and press 1 on the product The following screen will appear Enter Default e Custom e 4000K 10000K The available modes for Color Temp depend on the setting of Color Mode 4 Move to the desired option using the 1 A W buttons Next press the Bs button 5 The selected option will be applied 42 Configuring the Tint Settings Adjust the mid range brightness Gamma
20. of the picture Configuring Gamma 1 Press 0 on the product 2 Move to COLOR using the q A 2 W buttons Next press the I button 3 Move to Gamma using the 1 A 8 W buttons Next press the T button The following screen will appear E Enter 4 Move to the desired option using the 0 A 2 W buttons Next press the T button 5 The selected option will be applied 43 Chapter 8 Resizing or Relocating the Screen Change the picture size The available Image Size menu options depend on the setting of PC AV Mode under SETUP amp RESET Configuring Image Size 1 Press 1 on the product 2 Move to SIZE amp POSITION using the q A W buttons Next press the I button 3 Move to Image Size using the q A amp buttons Next press the T button The following screen will appear In PC mode Auto Wide e Auto Display the picture according to the aspect ratio of the input source e Wide Stretch the picture to full screen regardless of the aspect ratio of the input source In AV mode a 16 9 Screen Fit Move e 4 3 This mode is suitable to view the 4 3 aspect ratio picture of video content or standard broadcasts e 16 9 This mode is suitable to view the 16 9 aspect ratio picture of DVD content or widescreen broadcasts e Screen Fit This mode displays input without truncating the original picture e Adjusting the H Position and V Position
21. on Windows 7 Changing the Resolution on Windows Vista Go to Control Panel Display Screen Resolution and change the resolution Go to Control Panel Personalization Display Settings and change the resolution CE samaritan Toe Mp tata ant tre ete ogee a Date and Tena E coip Geiger ig Oes ang Printer iamm i npa menis Paa o ban hara Pg Connecting and Using a Source Device Connecting to a Video Device The product can be connected to a video device Connecting parts may differ in different products Connection Using an HDMI Cable _ M HDMI OUT KUA C HDMI IN gt BD 1 Connect the HDMI cable to the HDMI IN MHL port on the product and the HDMI port on the video device 2 Press the ie button on the product to change the input source to HDMI MHL e Open the SETUP amp RESET menu Next set PC AV Mode to AV 36 Chapter 6 Screen Setup Configure the screen settings such as brightness and color tone Dynamic Contrast Dynamic Contrast automatically adjusts the picture contrast to maintain a balance of bright and dark areas Changing the Dynamic Contrast Setting 1 Press O on the product 2 Move to PICTURE using the 0 A amp W buttons Next press the T button 3 Press 0 A amp W to move to Dynamic Contrast and press I The following screen will appear TE Enter e Off On 4 Move to the desired option usin
22. on how to use product or simply adjusts options without disassembling product If a defect is caused by external environmental factors Internet Antenna Wired Signal etc If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time If a product is reinstalled to move to a different spot or to move to a different house If customer requests instructions on how to use because of another company s product If customer requests instructions on how to use the network or another company s program If customer requests software installation and setup for the product If a service technician removes cleans dusts or foreign materials inside of the product If customer requests an installation additionally after purchasing a product through home shopping or online A Product damage caused by customer s fault Product damage caused by customer s mishandling or wrong repair If a product damage is caused by e external impact or drop use of supplies or separately sold product unspecified by Samsung repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co Ltd remodeling or repairing the product by customer using it with incorrect voltage or non authorised electrical connections not following the cautions in User Manual 63 Appendix Others e If product fails by natural disaster lightning fire eart
23. set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel Therefore a resolution other than the specified resolution may degrade the picture quality To avoid this it is recommended that you select the optimum resolution specified for the screen size of your product If a signal that belongs to the following standard signal modes is transmitted from your PC the screen will automatically be adjusted If the signal transmitted from the PC does not belong to the standard signal modes the screen may be blank even though the power LED turns on In such a case change the settings according to the following table by referring to the graphics card user manual IBM 640 x 350 31 469 70 086 25 175 VESA 640 x 480 31 469 59 940 251175 MAC 640 x 480 35 000 66 667 30 240 f VESA 640 x 480 37 861 72 809 31 500 f VESA 640 x 480 37 500 75 000 31 500 f IBM 720 x 400 31 469 70 087 28 322 st VESA 800 x 600 35 156 56 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 afar MAC 832 x 624 49 726 74155ill 57 284 JS VESA 1024 x 768 48 363 60 004 65 000 f VESA 1024 x 768 56 476 70 069 75 000 JE VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 58 Specifications MAC 1152 x 870 68 681 75 062 100 000 VESA 1280 x 800 49 702 59 810 83 500 afar VESA 1280 x 960 60 000 6
24. 0 000 108 000 VESA 1280 x 1024 63 981 60 020 108 000 VESA 1280 x 1024 79 976 75 025 135 000 VESA 1440 x 900 397995 59 887 106 500 si gt VESA 1600 x 1200 75 000 60 000 106 500 VESA 1680 x 1050 65 290 59 954 146 250 afar VESA 1920 x 1200 74 556 59 885 193 250 afar VESA 2560 x 1440 RB 88 787 59 951 241 500 Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle The reciprocal number of a horizontal cycle is called horizontal frequency Horizontal frequency is measured in kHz Vertical Frequency Repeating the same picture dozens of times per second allows you to view natural pictures The repeat frequency is called vertical frequency or refresh rate and is indicated in Hz Chapter 13 Appendix Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care Center CANADA MEXICO ARGENTINA BRAZIL BOLIVIA CHILE 1 800 SAMSUNG 726 7864 1 800 SAMSUNG 726 7864 01 800 SAMSUNG 726 7864 0800 333 3733 0800 124 421 4004 0000 800 10 7260 800 SAMSUNG 726 7864 From mobile 02 482 82 00 http www samsung com http www samsung com ca http www samsung com ca_fr French http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com COLOMBIA COS
25. GAPORE 1800 SAMSUNG 726 7864 http www samsung com 1800 29 3232 THAILAND 02 689 3232 http www samsung com 0800 329 999 TAIWAN 0266 026 066 http www samsung com VIETNAM 1 800 588 889 http www samsung com 62 Appendix IRAN OMAN KUWAIT BAHRAIN EGYPT JORDAN MOROCCO SAUDI ARABIA U A E CAMEROON COTE D LVOIRE GHANA KENYA NIGERIA SENEGAL SOUTH AFRICA TANZANIA UGANDA 021 8255 800 SAMSUNG 726 7864 183 2255 8000 4726 08000 726786 800 22273 080 100 2255 9200 21230 800 SAMSUNG 726 7864 7095 0077 8000 0077 0800 10077 0302 200077 0800 724 000 0800 726 7864 800 00 0077 0860 SAMSUNG 726 7864 0685 88 99 00 0800 300 300 http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com Responsibility for the Pay Service Cost to Customers When the service is requested in spite of in warranty we may charge you for a visit from a service technician in the following cases Not a product defect Cleaning of the product Adjustment Explanation Re installation and etc If a service technician gives instructions
26. H Position Menu V Position Move the menu position to the left or right Move the menu position up or down Configuring Menu H Position Configuring Menu V Position 1 Press I0 on the product 1 Press M0 on the product 2 Move to SIZE amp POSITION using the t A amp W buttons Next press the I button 2 Move to SIZE amp POSITION using the t A amp buttons Next press the button 3 Move to Menu H Position using the A W buttons Next press the EE button 3 Move to Menu V Position using the q A Q V buttons Next press the E3 button The following screen will appear The following screen will appear lt gt Adjust IE Enter lt gt Adjust E Enter 4 Adjust the Menu H Position setting using the A Q V buttons 4 Adjust the Menu V Position setting using the 0 4 lt W buttons 46 Chapter 9 Setup and Reset Adjust the power consumption of the product to save energy Configuring Eco Saving 1 Press 1 on the product 2 Move to SETUP amp RESET using the A Q V buttons Next press the F3 button 3 Move to Eco Saving using the A Q V buttons Next press the iE button The following screen will appear Move E Enter e 75 Reduce the power consumption of the product to 75 e 50 Reduce the power consumption of the product to 50 e Off Disable Eco Saving 4 Move to the desired option using the A e V b
27. Move to INFORMATION using the 0 A amp W buttons The current input source frequency and resolution will appear HDMI DVI mg Pa 7 0 SITION PICTURE COLOR YI SIZE8POSITION SETUP amp RESET DisplayPort PICTURE y COLOR IZE amp POSITION SETUP amp RESET Configure the Color Mode using the W buttons when no OSD menu is displayed 1 Press Q V when the initial screen is displayed The following screen will appear 2 Adjust the Color Mode setting using the Q A W buttons a Color Mode o senar X OM Exit Move E Enter e Standard High Bright Cinema sRGB Calibration 52 INFORMATION Menu and Others Configuring Volume in the Initial Screen Available only when the input source is DisplayPort or HDMI Adjust the Volume using the 0 A buttons when the initial screen that displays no menu screen is displayed 1 Press d A when the initial screen is displayed The following screen will appear Volume H es 100 O Exit Adjust TE Enter 2 Adjust the Volume setting using the Q A Q V buttons Configuring Brightness and Contrast in the Initial Screen Available only when the input source is DVI Adjust the Brightness or Contrast using the 0 A buttons when the initial screen that displays no menu screen is displayed 1 Press A when the initial sc
28. Munki Design i roduct name 11PUDIISI ro 11Display Pro factory before shipment aa ColorMunki Photo To obtain the optimum picture quality after calibration select Standard or sRGB mode on Heke the monitor Windows XP Windows XP Windows XP 32 amp 64 32 amp 64 32 amp 64 mie Windows Vista Windows Vista Windows Vista Pca 32 amp 64 32 amp 64 32 amp 64 systems Windows 7 Windows 7 Windows 7 32 amp 64 32 amp 64 32 amp 64 CA 210 CA 310 KONICA MINOLTA CA 210 CA 310 Windows XP 32 amp 64 Windows Vista 32 amp 64 Windows 7 32 amp 64 Windows 2000 19 Using NCE Natural Color Expert What is NCE Natural Color Expert The Natural Color Expert hereinafter NCE program was developed by Samsung Electronics to display optimized colors customized by users This product supports the monitor calibration feature through the internal NCE function and the provided NCE program a calibrator can be purchased separately NCE Program Installation Uninstallation Installation 1 Insert the installation CD into the CD ROM drive 2 Click the Natural Color Expert v2 installation program If the software installation screen does not pop up on the main screen go to CD ROM AutoPlay gt Manual NCE folder Next install using the Natural Color Expert v2 execution file 3 If the Natural Color Expert v2 InstallShield Wizard screen appears click Next and Install in sequence
29. TA RICA DOMINICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PERU PUERTO RICO TRINIDAD amp TO BAGO VENEZUELA 01 8000112112 0 800 507 7267 1 800 751 2676 1 800 10 7267 800 6225 1 800 299 0013 800 27919267 1 800 234 7267 00 1800 5077267 800 7267 0 800 777 08 1 800 682 3180 1 800 SAMSUNG 726 7864 0 800 100 5303 http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com 60 Appendix ALBANIA AUSTRIA BELGIUM BOSNIA BULGARIA CROATIA CZECH DENMARK FINLAND FRANCE GERMANY CYPRUS GREECE HUNGARY ITALIA KOSOVO LUXEMBURG EUROPE 42127 5755 0810 SAMSUNG 7267864 0 07 min 02 201 24 18 05 133 1999 07001 33 11 062 SAMSUNG 062 726 7864 800 SAMSUNG 800 726786 Samsung Electronics Czech and Slovak s r o Oasis Florenc Sokolovsk 394 17 180 00 Praha 8 70 70 19 70 030 6227 515 01 48 63 00 00 01805 SAMSUNG 726 7864 0 14 Min From landline 8009 4000 From landline 80111 SAM SUNG 7267864 From landline amp mobile 30 210 6897691 06 80 SAMSUNG 726 7864 800 SAMSUNG 726 7864 381 0113216899 261 03 710 http www samsung c
30. The message Check Signal Cable appears Check that the cable is properly connected to the product Check that the device connected to the product is powered on 54 Troubleshooting Guide The message Not Optimum Mode appears on the screen The images on the screen look distorted The screen is not clear The screen is blurry The screen appears unstable and shaky There are shadows or ghost images left on the screen The screen is too bright The screen is too dark Screen color is inconsistent The colors on the screen have a shadow and are distorted White does not really look white There is no image on the screen and the power LED blinks every 0 5 to 1 second Solutions This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product Set the maximum resolution and frequency according to the product specifications referring to the Standard Signal Mode Table Check the cable connection to the product Remove components video cable etc and try again Set the resolution and frequency to the recommended level Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product Then change the screen settings if required by referring to the additional information on the product menu Adjust the Brightness setting Adjust the COLOR settings Adjust the COLOR settings
31. duct off and then on again Mobile devices should be purchased separately 28 Using MHL 4 If the following message appears MHL mode is activated After about 3 seconds the MHL screen will be displayed HDMI MHL MHL The indicated time after 3 seconds may vary depending on the mobile device When the mobile device is in power saving mode If the mobile device is in power saving mode deactivate the power saving mode The MHL screen will appear normally When the mobile device is not connected or does not support MHL If MHL mode does not activate check the connection of the mobile device If MHL mode does not activate check if the mobile device supports MHL If MHL mode does not activate even though the mobile device supports MHL update the firmware on the device to the latest version Disabling MHL When the cable is disconnected or the mobile device is powered off If the HDMI MHL cable is disconnected or the mobile device is powered off when MHL is active the MHL function will be disabled If the mobile cable is disconnected HDMI MHL mode will still be enabled 29 Chapter 5 Connecting and Using a Source Device Checklist before Connecting to Pre connection Checkpoints aa Check the available ports on the back of the source device Sou rce Devices Refer to the user manual for the source device when connecting it to the product The number and locations of ports can vary depending on th
32. e PC AV Mode Configuring PC AV Mode Auto Source Configuring Auto Source Display Time Configuring Display Time Key Repeat Time Configuring Key Repeat Time Off Timer On Off Configuring Off Timer On Off Off Timer Setting Configuring Off Timer Setting Reset Restoring the default settings Reset Chapter 10 INFORMATION MENU AND OTHERS 52 INFORMATION 52 Viewing information INFORMATION 52 Configuring Color Mode in the Initial Screen 53 Configuring Volume in the Initial Screen 53 Configuring Brightness and Contrast in the Initial Screen Chapter 11 TROUBLESHOOTING GUIDE 54 Requirements Before Contacting Samsung Customer Service Center 54 Testing the Product 54 Checking the Resolution and Frequency 54 Check the following 56 Q amp A Chapter 12 SPECIFICATIONS 57 General 58 PowerSaver 58 Preset Timing Modes Chapter 13 APPENDIX 60 Contact SAMSUNG WORLDWIDE 63 Responsibility for the Pay Service Cost to Customers 64 Correct Disposal 65 Terminology 65 OSD On Screen Display 65 Gamma 65 Grey scale 65 Scanning rate 65 Horizontal Frequency 65 Vertical Frequency 65 Resolution 65 Plug amp Play 65 MHL Mobile High Definition Link Chapter 1 Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality 2012 Samsung Electronics Samsung Electronics owns the copyright for this manual Use or reproduction of this manua
33. e source device Check the following before you connect this product with other devices Do not connect the power cable until all connections are completed Connecting the power You can connect a camcorder audio player or DVD player to the product cable during connection may damage the product Note that the optimal performance can be achieved when the resolution of the source device is Full HD 1080p Connecting the Powe SAMSUNG 1 Connect the power cable to the DC power adapter Next connect the adapter to the product 30 Connecting and Using a Source Device Connecting and Using a PC Connecting to a PC Select a connection method suitable for your PC Connecting parts may differ in different products Connection Using an HDMI DVI Cable HDMI IN MHL NU 1 Connect the HDMI DVI cable to the HDMI IN MHL port on the back of the product and the DVI port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC 3 Press the button on the product to change the input source to HDMI MHL NOTE e Open the SETUP amp RESET menu Next set PC AV Mode to PC e Audio is not available if the source device is connected using an HDMI DVI cable Connection Using an HDMI Cable Digital Type HDMI IN HDMI OUT KA EO 1 Connect the HDMI cable to the HDMI IN MHL port on the back of the product and the
34. fects screen flicker Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen I represents the level of display detail A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time E g A resolution of 1920 x 1080 consists of 1920 horizontal pixels horizontal resolution and 1080 vertical lines vertical resolution Plug amp Play The Plug amp Play feature allows the automatic exchange of information between a monitor and PC to produce an optimum display environment The monitor uses VESA DDC international standard to execute Plug amp Play MHL Mobile High Definition Link The MHL feature allows you to view videos and photos saved on a connected mobile device that supports MHL using the product screen 65 Index Index Auto Source 49 Blue 42 Brightness 37 Checking the Contents 13 Cleaning 7 Color Mode 40 Color Temp 42 Compatible Types of C alibrators 19 Completing Calibration 27 Components 14 Configuring Brightness and Contrast in the Initial Screen 53 Configuring Color Mode 40 Configuring Color Mode in the Initial Screen 52 Configuring Volume in the Initial Screen 53 Connecting and UsingaPC 31 Connecting the Calibrator 21 Connecting the Product to a PC as a USB HUB 33 Connecting to a Video Device 36 Contact SAMSUNG WORLDWIDE 60 Contrast 38 Copyright 5 Correct Disposa
35. g the 0 A amp W buttons Next press the T button 5 The selected option will be applied Brightness You can adjust the general brightness of the picture Range 0 100 A higher value will make the picture appear brighter This option is enabled if Dynamic Contrast is set to Off Configuring Brightness 1 Press O0 on the product 2 Move to PICTURE using the 0 A amp W buttons Next press the T button 3 Move to Brightness using the q A W buttons Next press the E button The following screen will appear 0 Return lt gt Adjust TE Enter 4 Adjust the Brightness setting using the t A s W buttons 3 Screen Setup Adjust the contrast between the objects and background Range 0 100 Make the outline of objects more clear or blurry Range 0 100 A higher value will increase the contrast to make the object appear clearer A higher value will make the outline of objects clearer NOTE NOTE This option is enabled if Dynamic Contrast is set to Off This option is enabled if Dynamic Contrast is set to Off Configuring Contrast Configuring Sharpness 1 Press M0 on the product 1 Press M0 on the product 2 Move to PICTURE using the 1 4 2 v buttons Next press the T button 2 Move to PICTURE using the 0 A 2 buttons Next press the T button 3 Move to Contrast using the 0 A 2 v buttons Next press the iT button The 3 Move to Sharpness u
36. he following images are for reference only Real life situations may differ from what is shown in the images Warning ies Do not use a damaged power cable or plug or a loose power socket ew An electric shock or fire may result Do not use multiple products with a single power socket Otherwise the socket may cause a fire Do not touch the power cable with wet hands Otherwise an electric shock may result Insert the power cable all the way in so it is not loose An unsecure connection may cause a fire Be sure to plug the power cable into a grounded power socket type 1 insulated devices only An electric shock or injury may result Before Using the Product BC Cor Do not bend or pull the power cable with force Also do not place a heavy object on the power cable Damage to the cord may result in a fire or electric shock Do not place the power cable or product near heat sources A fire or electric shock may result Clean any dust around the pins of the power cable or the power outlet using a dry cloth A fire may result Do not disconnect the power cable while the product is being used The product may become damaged by an electric shock Only use the power cable provided with your product by Samsung Do not use the power cord with other products A fire or electric shock may result Keep the power soc
37. he target settings as desired and perform calibration according to the modified settings Brightness Black Level ut Set Black Level Control Calibration si R 0 6400 0 3300 G 0 3000 0 6000 B 0 1500 0 0600 EB RGB Gamma 1 Select a profile from the NCE Profile List 2 Click the Edit button to change the settings 3 After changing the settings as desired click the Calibration button 23 Using NCE Natural Color Expert Layout and Menu Items on the Calibration Layout and Menu Items on the New Profile Screen Screen If profiles exist in the NCE Profile List you can select a profile and perform calibration As no profile exists when you use the NCE program for the first time after purchase go to New according to the settings of the selected profile Profile and create a profile Standard Profile List Home 1 Select New Profile NCE Profile List SES Mode Last Update Profile List BANYO BADA NG bee LI 650K LUT 20720000 0120120 t Home SDO AOD 199 BOC 3 poen eso 2 XWW 23912 0929 SEPIO GE 290 000 O Vant CDI 2 IMINO moan 0 nama wnan POPE PASEE SEE SEN ama mad 58079 SCE Det 6002 2 30120820 BROTO AGO 49 Bea 2 Jent NOOB IK LUT 20120331 SOPO NAGO 49 BO D BIO NOOOIKLUT 20120493 NCE Profile List i Po Last Update SOOT BADA NG bee LII 600K LUT 20720090 20120220 BUHO ROD Nap B3 Poe CSR 2 2912 00 29 Profile Information 0970 AG POSTE EE Pr
38. hquake flood damage etc e If consumable components are all used up Battery Toner Fluorescent lights Head Vibrator Lamp Filter Ribbon etc If customer requests a service in case the product has no defect service fee may be charged So please read User Manual first Correct Disposal Correct Disposal of This Product Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return sy
39. k 28 Using MHL 29 Disabling MHL Chapter 5 CONNECTING AND USING A SOURCE DEVICE 30 Checklist before Connecting to Source Devices 30 Pre connection Checkpoints 30 Connecting the Power 31 Connecting and Using a PC 31 Connecting to a PC 33 Driver Installation 34 Setting Optimum Resolution 34 Changing the Resolution Using a PC 36 Connecting to a Video Device Chapter 6 SCREEN SETUP 37 Dynamic Contrast 37 Changing the Dynamic Contrast Setting 37 Brightness 37 Configuring Brightness 38 Contrast 38 Configuring Contrast 38 Sharpness 38 Configuring Sharpness 39 Response Time 39 Configuring Response Time 39 HDMI Black Level 39 Configuring HDMI Black Level Chapter 7 CONFIGURING THE TINT SETTINGS 40 Color Mode 40 Configuring Color Mode 41 Red 41 Configuring Red 41 Green 41 Configuring Green 42 Blue 42 Configuring Blue 42 Color Temp 42 Configuring Color Temp 43 Gamma 43 Configuring Gamma Chapter 8 RESIZING OR RELOCATING THE SCREEN 44 Image Size 44 Configuring Image Size 45 H Position 45 Configuring H Position 45 V Position 45 Configuring V Position 46 Menu H Position 46 Configuring Menu H Position 46 Menu V Position 46 Configuring Menu V Position Chapter 9 SETUP AND RESET 47 47 47 47 48 48 48 48 49 49 49 49 50 50 50 50 51 51 51 51 Eco Saving Configuring Eco Saving Menu Transparency Configuring Menu Transparency Language Configuring Languag
40. ket where the power cable is connected unobstructed In the event of a problem with the product you must disconnect the power cable to cut the power supply to the product Hold the plug when disconnecting the power cable from the power socket A fire or electric shock may result Installation and Safety The following images are for reference only Real life situations may differ from what is shown in the images Warning 8 3 DO NOT PLACE CANDLES INSECT REPELLANTS OR CIGARETTES ON TOP m OF THE PRODUCT DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES rc Gf iy 4 NA ad A lt Afire may resullt Do not install the product in poorly ventilated spaces such as a bookcase or closet An increased internal temperature may cause a fire Keep the plastic packaging out of the reach of children Children may suffocate Do not install the product on an unstable or vibrating surface insecure shelf sloped surface etc The product may fall and become damaged and or cause an injury Using the product in an area with excess vibration may damage the product or cause a fire Do not install the product in a vehicle or a place exposed to dust moisture water drips etc oil or smoke A fire or electric shock may result Do not expose the product to direct sunlight heat or a hot
41. l 64 Correct posture to use the product 12 Customer Registration 60 Display Time 49 Dynamic Contrast 37 Eco Saving 47 Features of the NCE Program 21 Gamma 43 General 57 Green 41 HDMI Black Level 39 H Position 45 Image Size 44 INFORMATION 52 Items sold separately 14 Key Repeat Time 50 Language 48 Layout and Menu Items on the Calibration Screen 24 Layout and Menu Items on the Edit Screen 23 Layout and Menu Items on the NCE Home Screen 21 Layout and Menu Items on the New Profile Screen 24 Layout and Menu Items on the Uniformity Screen 23 Menu H Position 46 Menu Transparency 47 Menu V Position 46 MHL 28 66 NCE Program Installation Uninstallation 20 Off Timer On Off 50 Off Timer Setting 51 Parts 15 PC AV Mode 48 Power Consumption 58 PowerSaver 58 Preparing for Calibration 27 Profile List 22 Q amp A 56 Red 41 Requirements Before Contacting Samsung Customer Service Center 54 Reset 51 Response Time 39 Responsibility for the Pay Service Cost to Customers 63 Safety Precautions 6 Sharpness 38 Starting NCE Natural Color Expert 21 Terminology 65 Using MHL 28 V Position 45 What is Monitor Calibration 19 What is NCE Natural Color Expert 20 67
42. l in parts or entirety without the authorization of Samsung Electronics is prohibited The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics Microsoft and Windows are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of the Video Electronics Standards Association Ownership of all other trademarks is attributed to their due owner e An administration fee may be charged if either o a an engineer is called out at your request and there is no defect in the product i e where you have failed to read this user manual o b you bring the unit to a repair center and there is no defect in the product i e where you have failed to read this user manual e The amount of such administration charge will be advised to you before any work or home visit is carried out Before Using the Product Securing the Installation Space Safety Precautions Ensure some space around the product for ventilation An internal temperature rise may cause fire and damage the product Be sure to allow the amount of space as shown below or greater Caution when installing the product Do not open the cover You may suffer an electric shock The components inside this The exterior may differ depending on the product product must not be repaired by home users Contact a technician for repair Symbols Warning A serious or fatal injury may result if instructions are not followed
43. m area between black and white Changing the grey scale through Gamma adjustment will change the medium brightness on the screen Scanning rate Scanning rate or refresh rate refers to the frequency of screen refreshes Screen data is transmitted as it refreshes to display an image although the refreshing is invisible to the naked eye The number of screen refreshes is called scanning rate and is measured in Hz A scanning rate of 60Hz means that the screen refreshes 60 times per second The screen scanning rate depends on the performance of the graphics cards in your PC and monitor Horizontal Frequency Characters or images displayed on the monitor screen consist of numerous dots pixels Pixels are transmitted in horizontal lines which are then arranged vertically to create an image The horizontal frequency is measured in kHz and represents how many times horizontal lines per second are transmitted and displayed on the monitor screen A horizontal frequency of 85 means that the horizontal lines that make up an image are transmitted 85000 times per second The horizontal frequency is indicated in 85kHz Vertical Frequency One image is made of numerous horizontal lines The vertical frequency is measured in Hz and represents how many images can be created per second by those horizontal lines A vertical frequency of 60 means that an image is transmitted 60 times per second The vertical frequency is also called refresh rate and af
44. o http www samsung com http www samsung com be Dutch http www samsung com be_fr French http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com MACEDONIA MONTENEGRO NETHERLANDS NORWAY POLAND PORTUGAL RUMANIA SERBIA SLOVAKIA SPAIN SWEDEN SWITZERLAND U K EIRE LITHUANIA LATVIA ESTONIA TURKEY 023 207 777 020 405 888 0900 SAMSUNG 0900 7267864 0 10 Min 815 56 480 0 801 1SAMSUNG 172 678 48 22 607 93 33 808 20 SAMSUNG 808 20 7267 From landline 08010 SAM SUNG 7267864 From landline amp mobile 40 21 206 01 10 0700 SAMSUNG 0700 726 7864 0800 SAMSUNG 0800 726786 902 1 SAMSUNG 902 172 678 0771 726 7864 SAMSUNG 0848 SAMSUNG 7267864 CHF 0 08 min 0330 SAMSUNG 7267864 0818 717100 8 800 77777 8000 7267 800 7267 444 77 11 http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung
45. object such as a stove The product lifespan may be reduced or a fire may result Before Using the Product Do not install the product within the reach of young children The product may fall and injure children Edible oil such as soybean oil can damage or deform the product Do not install the product in a kitchen or near a kitchen counter Do not drop the product while moving Product failure or personal injury may result Do not set down the product on its front a J The screen may become damaged When installing the product on a cabinet or shelf make sure that the bottom edge of the front of the product is not protruding The product may fall and break or cause a personal injury Install the product only on cabinets or shelves of the right size Set down the product gently Product failure or personal injury may result ve Installing the product in an unusual place a place exposed to a lot of fine particles chemical substances or extreme temperatures or an airport or train station where the product should operate continuously for an extended period of time may seriously affect its performance Be sure to consult Samsung Customer Service Center if you want to install the product at such a place Operation and Safety The following images are for reference only Real life situations ma
46. objects on the product or apply impact A fire or electric shock may result Do not pull on the product holding only the power cable or any other cable Product failure an electric shock or fire may result from a damaged cable If a gas leakage is found do not touch the product or power cable Also ventilate the area immediately Sparks can cause an explosion or fire Do not lift or move the product by pulling the power cable or any cable Product failure an electric shock or fire may result from a damaged cable Do not use or keep combustible spray or an inflammable substance near the product An explosion or fire may result Ensure the vents are not blocked by tablecloths or curtains An increased internal temperature may cause a fire Do not insert metallic objects chopsticks coins hairpins etc or objects that burn easily paper matches etc into the product via the vent or input output ports etc Be sure to power off the product and disconnect the power cable when water or other foreign substances have entered the product Then contact Samsung Customer Service Center Product failure an electric shock or fire may result Do not place objects containing liquid vases pots bottles etc or metallic objects on top of the product Be sure to power off the product and disconnect the power cable when water or other foreign substances have entered the product Then
47. ock 241 5 MHz DL DVI www samsung com recyclingdirect or call 877 278 0799 This product uses 100 to 240 V Power Supply Refer to the label at the back of the product as the standard voltage can vary in different countries Side View USB 1UP 2DN USB2 0 Ports Rear View DVI Dual link HDMI MHL DisplayPort Internal Speaker 7 0W X 2 Channel 57 Specifications PowerSave The power saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time The power is not turned off in power saving mode To switch the screen back on press any key on the keyboard or move the mouse Power saving mode functions only when the product is connected to a PC that has a power saving function Power lamp Blinking 53 W W O USB less than 0 5 W less than 0 5 W Power Consumption 63 W W USB less than 0 5 W less than 0 5 W The power consumption level can vary in different operating conditions or when settings are changed To reduce the power consumption to 0 watts turn off the power switch on the back of the product or disconnect the power cable Be sure to disconnect the power cable when you will not be using the product for an extended period of time To reduce the power consumption to 0 watts when the power switch is not available disconnect the power cable Preset Timing Modes This product can be
48. ofile Information Preference Uniformity Calibration 1 Select a profile from the NCE Profile List 2 Click the Calibration button to proceed with calibration according to the settings of the ms aaa selected profile Using NCE Natural Color Expert 2 Specify the color gamut Select SRGB or User Settings New Profile Standard Color Gamut Calibration Redy Green y Bluey 3 Configure the Brightness The brightness level after calibration may depend on the color temperature New Profile 29 Standard Brightness 4 Configure the Black Level setting If you do not adjust the black level setting by moving the slider button the minimum brightness will automatically be applied New Profile Standard Black Level Black Level Min Set Black Level Control Cancel 5 Configure the color temperature for White Point range 4000K 10000K To select a standard brightness click the Standard button New Profile Standard White Point 25 Using NCE Natural Color Expert 6 Configure the Gamma settings If you configure LUT the gamma curve of sRGB will be applied New Profile Standard Linear Gray deep Black 7 Start calibration Measurement Select a Calibrator Monitor Calibration Cancel Cancel Advanced 1 You can perform basic configuration using a single menu screen Color Gamut Calibration
49. ove the styrofoam from the product Removing the Packaging The appearance of the actual product may differ from the images shown 1 Open the packaging box Be careful not to damage the product when you open the packaging with a sharp instrument 3 Check the product and remove the styrofoam and plastic bag e The appearance of the actual product may differ from the image shown e This image is for reference only 4 Store the box in a dry area so that it can be used when moving the product in the future 13 Preparation Checking the Components Contact the vendor where you purchased the product if any components are missing The appearance of the components and items sold separately may differ from the image shown Components Components may vary depending on the country lt A S amp S Bp Quick setup guide Warranty card Natural Color Expert User manual Not available in Data Sheet some locations o amp OC 8 Cleaning cloth DP cable Power cable DC power adapter Creat Ps Z USB 2 0 cable HDMI MHL cable Dual link DVI cable Items sold separately The following items can be purchased at your nearest retailer HDMI DVI cable HDMI cable 14 Preparation Front Buttons The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality This is a touch type button Tap the button lightly with a finger
50. reen is displayed The following screen will appear Contrast 2 Es 75 O Exit Adjust E Enter 2 Adjust the Brightness and Contrast setting using the 0 A Q V buttons 53 Chapter 11 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Cente Before calling Samsung Customer Service Center test your product as follows If the problem persists contact Samsung Customer Service Center Testing the Product Check if your product is operating normally by using the product test function If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC perform a self diagnosis test 1 Power off both the PC and product 2 Disconnect the cables from the product 3 Power on the product 4 If the message Check Signal Cable appears the product is working normally If the screen remains blank check the PC system video controller and cable Checking the Resolution and Frequency For a mode that exceeds the supported resolution refer to Preset Timing Modes the message Not Optimum Mode will appear repeatedly Check the following Installation issue PC mode The screen keeps Check that the cables are properly connected between the switching on and off product and PC and that the connectors are firmly locked Screen issue The power LED is off Make sure that the power cable is connected The screen will not switch on
51. s gt Advanced gt Monitor and adjust Refresh rate under Monitor settings Windows ME 2000 Go to Control Panel gt Display gt Settings Advanced Monitor and adjust Refresh rate under Monitor settings Windows Vista Go to Control Panel gt Appearance and Personalization Personalization Display Settings Advanced Settings Monitor and adjust Refresh rate under Monitor settings Windows 7 Go to Control Panel gt Appearance and Personalization Display Screen Resolution Advanced settings Monitor and adjust Refresh rate under Monitor settings Windows XP Go to Control Panel gt Appearance and Themes Display Settings and adjust the resolution Windows ME 2000 Go to Control Panel Display gt Settings and adjust the resolution Windows Vista Go to Control Panel gt Appearance and Personalization Personalize Display Settings and adjust the resolution Windows 7 Go to Control Panel gt Appearance and Personalization Display Adjust Resolution and adjust the resolution How do I set power saving mode e Windows XP Set power saving mode in Control Panel Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC e Windows ME 2000 Set power saving mode in Control Panel gt Display Screen Saver Settings or BIOS SETUP on the PC e Windows Vista Set power saving mode in Control Panel gt
52. settings is possible if Image Size is set to Screen Fit 4 Move to the desired option using the Q A e V buttons Next press the T button 5 The selected option will be applied 44 Resizing or Relocating the Screen Move the screen to the left or right Move the screen up or down NOTE NOTE Adjusting the H Position and V Position settings is possible if Image Size is set to Screen Fit Adjusting the H Position and V Position settings is possible if Image Size is set to Screen Fit Configuring H Position Configuring V Position 1 Press 0 on the product 1 Press M10 on the product 2 Move to SIZE amp POSITION using the A amp W buttons Next press the i button 2 Move to SIZE amp POSITION using the q A amp W buttons Next press the E button 3 Move to H Position using the q A Q V buttons Next press the f4 button 3 Move to V Position using the 0 A lt amp W buttons Next press the E button The following screen will appear The following screen will appear lt gt Adjust TE Enter O Re e Adjusting the H Position and V Position settings is possible if Image Size is set to Screen Fit e Adjusting the H Position and V Position settings is possible if Image Size is set to Screen Fit 4 Adjust the H Position setting using the q A buttons 4 Adjust the V Position setting using the A buttons 45 Resizing or Relocating the Screen Menu
53. si R 0 6400 0 3300 G 0 3000 0 6000 B 0 1500 0 0600 2 Start calibration Calibration Target Result 4 Brighiness O Black Level Set Black Level Control White Point WD RGB Gamma Calibration Select a Calibrator Cancel 26 Using NCE Natural Color Expert Preparing for Calibration 1 Select the connected calibrator then click Next 2 If the calibrator initialization screen appears start measurement using the calibrator Calibration bb ma Select a Calibrator Cancel 3 Attach the calibrator to the indicated spot on the screen then click Next e Set the screensaver time to at least 30 minutes before starting measurement e The calibration process will be performed in full screen To cancel a calibration that is in progress press the ESC key 4 Measurement will be performed 5 The settings for Color Gamut Brightness Black Level White Point and RGB Gamma can be finely adjusted Completing Calibration Mfter calibration you can compare the screens before and after the calibration using the After Before buttons Calibration Skipped LUTILUTALUT LUTU Finish Add or delete images as desired using the Custom category Click Finish to save the calibration results to Preference on the monitor 27 Chapter 4 Using MHL Using MHL MHL Mobile High Definition Link Connect a mobile device that supports MHL to the product
54. sing the 0 A 8 w buttons Next press the iT button The following screen will appear following screen will appear lt gt Adjust FY Enter lt gt Adjust E Enter 4 Adjust the Contrast setting using the 0 A amp W buttons 4 Adjust the Sharpness setting using the t0 A amp W buttons 38 Screen Setup Accelerate the panel response rate to make video appear more vivid and natural e It is recommended to set the response rate to Normal or Faster when you are not viewing a video e The functions available may vary depending on the product model Refer to the actual product Configurin 1 Press I0 on the product Response Time 2 Move to PICTURE using the 0 4 2 v buttons Next press the T button 3 Move to Response Time using the 0 4 W buttons Next press the E button The following screen will appear E Enter e Normal Faster Fastest 4 Move to the desired option using the q A 2 W buttons Next press the T button 5 The selected option will be applied HDMI Black Level If you connect a DVD player or set top box to the product using an HDMI cable the contrast and color may degrade making the picture look darker If this is the case correct the degraded picture quality using the HDMI Black Level menu Configuring HDMI Black Level 1 Press M0 on the product 2 Move to PICTURE using the q A Q V buttons Next press the EE but
55. stems The marking on the battery manual or packaging indicates that the battery in this product should not be disposed of with other household waste Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 The battery incorporated in this product is not user replaceable For information on its replacement please contact your service provider Do not attempt to remove the battery or dispose it in a fire Do not disassemble crush or puncture the battery If you intend to discard the product the waste collection site will take the appropriate measures for the recycling and treatment of the product including the battery 64 Appendix erminology OSD On Screen Display On screen display OSD allows you to customize on screen settings to optimize the picture quality as required You can change the screen brightness tint size and many other settings using menus displayed on the screen The Gamma menu adjusts the grey scale that represents middle tones on the screen Adjusting the brightness brightens the whole screen but adjusting Gamma only brightens the medium brightness Grey scale Scale refers to levels of color intensity that show variations of color change from darker areas to brighter areas on the screen Changes to the screen brightness are expressed with black and white variation and grey scale refers to the mediu
56. the NCE program If you select a profile and perform calibration changed settings from the calibration will be saved to Calibration mode Preference 4 New Profile Mode Go to the Samsung Electronics website Measure the current monitor settings COLOR Uniformity View the measurement and calibration logs by date Select Standard or Advanced to specify the profile mode if you have selected New in the home screen Configure the Preview Image setting if you have set New Profile Mode to Standard 22 Using NCE Natural Color Expert Layout and Menu Items on the Uniformity Screen O Only Brightness Brightness Color Auto setting User Settings Specify the number of blocks that will be displayed on the screen when Uniformity 1 calibration is carried out A greater number of blocks will increase the precision of uniformity calibration Select Only Brightness to perform calibration only for the brightness Select Brightness Color to perform calibration for both the brightness and colors If you select Brightness Color the color temperature uniformity will also increase from calibration Specify the color temperature when performing calibration To obtain a more 3 accurate color temperature performing Uniformity calibration before color calibration is recommended Layout and Menu Items on the Edit Screen If profiles exist in the NCE Profile List you can select a profile modify t
57. the device from the product without having to connect the device to the PC 1 Connect the USB cable to PC IN on the back of the product and USB on the PC 2 Using the product as a hub connect and use various source devices with the product at the same time e APC cannot connect to multiple source devices at the same time as it has a limited number of input output ports available The HUB feature on the product will improve your work efficiency by allowing you to connect multiple source devices to the USB ports on the product at the same time without connecting them to a PC e If source devices are connected to the PC the numerous cables around the PC can get tangled and look messy Connecting them directly to the product will resolve this PC IN e An external mass storage HDD requires external power supply Be sure to connect it to a power source Driver Installation nn e You can set the optimum resolution and frequency for this product by installing the corresponding drivers e An installation driver is contained on the CD supplied with the product e If the provided file is faulty visit the Samsung Electronics homepage http www samsung com and download the file 1 Insert the user manual CD provided with the product into the CD ROM drive 2 Click Windows Driver 3 Follow the instructions given on the screen to proceed with installation 4 Select your product model from the list of models
58. ton 3 Move to HDMI Black Level using the 0 A 8 W buttons Next press the Ts button The following screen will appear e Normal Set the brightness of the darkest parts of the screen to be normal e Low Set the brightness of the darkest parts of the screen to be darker than Normal mode 4 Move to the desired option using the q A 2 v buttons Next press the tre button 5 The selected option will be applied e Available only when the product is connected to a source device using an HDMI cable e The HDMI Black Level function may not be compatible with some source devices 39 Chapter 7 Configuring the Tint Settings Adjust the tint of the screen Adjust the tint of the screen T0 0 amu ele This option is enabled if Dynamic Contrast is set to Off Configuring Color Made 1 Press 1 on the product 2 Move to COLOR using the q A 23 v buttons Next press the EE button 3 Move to Color Mode using the 2 A Q V buttons Next press the R2 button The following screen will appear Standard High Bright Cinema sRGB Calibration e Standard Some users may not find the brightness and sharpness comfortable for their eyes in this mode If this is the case adjust the brightness and sharpness e When Color Mode is set to Standard the default mode for Color Temp is set to Default e If changing the settings for Red Green and Blue the mode of Color Temp will change to
59. uttons Next press the Z737 button 5 The selected option will be applied Menu Transparency Configure the transparency for the menu windows Configuring Menu Transparency 1 Press 10 on the product 2 Move to SETUP amp RESET using the Q A e V buttons Next press the F3 button 3 Move to Menu Transparency using the A e V buttons Next press the R2 button The following screen will appear Move IE Enter 4 Move to the desired option using the A Q V buttons Next press the fx button 5 The selected option will be applied 47 Setup and Reset Set the menu language e A change to the language setting will only be applied to the onscreen menu display e It will not be applied to other functions on your PC Configuring Language 1 Press 00 on the product 2 Move to SETUP amp RESET using the q A Q V buttons Next press the F5 button 3 Move to Language using the q A amp W buttons Next press the E button The following screen will appear Enter 4 Move to the desired option using the q A e V buttons Next press the 35 button 5 The selected option will be applied PC AV Mode Set PC AV Mode to AV The size of the image displayed on the screen will be enlarged This option is useful when viewing a movie Configuring PC AV Mode 1 Press 0 on the product 2 Move to SETUP amp RESET using the 0P
60. wing screen will appear e 5 sec 10 sec 20 sec 200 sec 4 Move to the desired option using the A Q V buttons Next press the F3 button 5 The selected option will be applied 49 Setup and Reset Key Repeat Time Control the response rate of a button when the button is pressed Configuring Key Repeat Time 1 Press M0 on the product 2 Move to SETUP amp RESET using the A W buttons Next press the F3 button 3 Move to Key Repeat Time using the q A Q V buttons Next press the iT button The following screen will appear EF Enter e The available options include Acceleration 1 sec and 2 sec If No Repeat is selected a button will respond only when it is pressed 4 Move to the desired option using the 2 A Q V buttons Next press the F5 button 5 The selected option will be applied Off Timer On Of You can set the product to automatically turn off Configuring Off Timer On Off 1 Press M0 on the product 2 Move to SETUP amp RESET using the A Q V buttons Next press the F3 button 3 Move to Off Timer On Off using the A Q V buttons Next press the F3 button The following screen will appear IF Enter e Off Deactivate the off timer so that the product does not power off automatically e On Activate the off timer so that the product powers off automatically 4 Move to the desired option using the A
61. y differ from what is shown in the images Warning There is a high voltage inside the product Never disassemble repair or modify the product yourself A fire or electric shock may result Contact Samsung Customer Service Center for repairs Before moving the product turn off the power switch and disconnect the power cable and all other connected cables Damage to the cord may result in a fire or electric shock If the product generates abnormal sounds a burning smell or smoke disconnect the power cable immediately and contact Samsung Customer Service Center An electric shock or fire may result Do not let children hang from the product or climb on top of it Children may become injured or seriously harmed Before Using the Product If the product is dropped or the outer case is damaged turn off the power switch and disconnect the power cable Then contact Samsung Customer Service Center Continued use can result in a fire or electric shock Do not leave heavy objects or items that children like toys sweets etc on top of the product The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury If there is a thunderstorm or lightning strike turn off the power and disconnect the power cable A fire or electric shock may result Do not drop

Samsung S27B970D User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents