Samsung PS-50C62H User's Manual
Contents
1. i PDP TELEVISION PLASMA DISPLAY PANEL Owner s Instructions Before operating the unit please read this manual thoroughly and retain it for future reference ON SCREEN MENUS Picture In Picture PIP Energy Saving TELETEXT option SRS TruSurround XT Digital Natural Image engine Register your product at www samsung com global register Record your Model and Serial number here for future reference BN68 01337C 01 Model Serial No User Instructions Screen Image retention Do not display a still image such as on a video game or when hooking up a PC to this PDP on the plasma monitor panel for more than 2 hours as it can cause screen image retention This image retention is also known as screen burn To avoid such image retention reduce the degree of brightness and contrast of the screen when displaying a still image Height The PDP can normally operate only under 2000m in height It might abnormally function at a place over 2000m in height so do not install and operate there Heat on the top of the PDP TV The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product This is normal and does not indicate any defect or operation failure of the product However children should be prevented from touching the upper part of the product The product is making a cracking noise A cracking no2. Connector for service EXT 1 EXT 2 Connect the serial jack between the Inputs or outputs for external devices such as electro motion wall mount bracket and your VCR DVD video game device or video disc TV when you want to adjust the TV viewing players angle using your remote control PEES PC IN AUDIO Input Output Specification Connect to the video and audio output jack on Connector Input Output your PC Video Audio L R RGB Video Audio L R Only TV output is i es oe vailabe Output you can EXT 2 v v choose Continued English 6 HDMI IN DVI IN ANTIN Connect to the HDMI jack of a device with 750 Coaxial connector for Aerial Cable HDMI output These inputs can also be used Network as a DVI connection with separate analog audio inputs An optional HDMI DVI cable Supported modes for HDMI and Component will be necessary to make this connection 480i 480p 576i 576p 720p 1080i When using the optional HDMI DVI adapter HDMI DVI 50Hz __X X X ojojo the DVI analog audio inputs on your TV HDMI DVI 60Hz X O X X o o allow you to receive left and right audio from Component ojo ojojoj jo your DVI device Not compatible with PC When connecting this product via HDMI or DVI to a Set Top Box DVD Player or Games Console etc make sure that it has been set to a compatible video output mode as shown in the table below Failure to observe this may resul
3. Wall Mount Kit Specifications VESA Install your wall mount on a solid wall perpendicular to the floor When attaching to other building materials please contact your nearest dealer If installed on a ceiling or slanted wall it may fall and result in severe personal injury Product Family inch VESA Spec A B Standard Screw Quantity 23 26 200 100 M4 32 40 200 200 M6 46 52 600 400 LCD TV 4 57 700 400 No VESA No M8 57 70 800 400 80 1400 800 42 58 600 400 4 70 800 400 PDP TV M8 63 No VESA 6 80 1400 800 4 gt We provided the standard dimensions for wall mount kits as shown in the table above gt gt When purchasing our wall mount kit a detailed installation manual and all parts necessary for assembly are provided gt Do not use screws longer than the standard dimension as they may cause damage to the inside of the TV set gt For wall mounts that do not comply with the VESA standard screw specifications the length of the screws may differ depending on their specifications gt Do not use screws that do not comply with the VESA standard screw specifications Do not use fasten the screws too strongly this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents gt Samsung is not liable for product damage or personal injury when a non VESA or non specified wall m
4. selecting game menu L a Lang gt Press the MENU button to display the menu Press the A or Y button to select Setup then press the alate k ENTER button gt Home Theatre PC Off gt Press the A or Y button to select Game Mode then press the Dianeine in ocndby aay ENTER button nergy ig Off gt Y More Select Off or On by pressing the A or Y button then press the ENTER button Press the EXIT button to exit gt To disconnect the game console and connect another external device cancel game mode in the setup menu gt If you display the TV menu in Game mode the screen shakes slightly gt Game Mode is not available in TV mode gt If Game Mode is On Picture Mode is automatically changed to Standard and users cannot change the mode Sound Mode in the Sound menu is deactivated Adjust the sound using the equalizer The Reset Sound function is activated Selecting the Reset function after setting the equalizer resets the equalizer setting to the factory defaults Move Enter Return English 26 Wall mount adjustment Sold separately Once the wall mount is installed the position of your TV can be easily adjustable Rear Panel MOJICH Serial Cable 1P to 1P Not supplied Entering the menu 14 Press the MENU button to display the menu Press the A or Y button to select Setup then pre
5. Picture freeze Picture size selection Sub picture PIP channel selection Sub picture PIP source selection Sub picture PIP location selection Teletext Functions Refer to page 34 C0 88609 eee Exit from the teletext display depending on the model Teletext index Teletext reveal Teletext hold Teletext mode selection LIST FLOF Teletext sub page P O Teletext next page P Teletext previous page Teletext cancel Teletext display mix both teletext information and the normal broadcast Fastext topic selection Teletext store Teletext size English 8 Continued Installing Batteries in the Remote Control 1 2 3 Lift the cover at the back of the remote control upward as shown in the figure Install two AAA size batteries gt Make sure to match the and ends of the batteries with the diagram inside the compartment Do not mix battery types i e alkaline and manganese Close the cover as shown in the figure i gt Remove the batteries and store them in a cool and dry place if you won t be using the remote control for a long H i time The remote control can be used up to about 23 feet to eee from the TV Assuming typical TV usage the batteries last for about one year gt Ifthe remote control doesn t work Check the following 1 Is the TV power on 2 Are the plus and minus ends of the batteries reversed 3 Are th
6. Standard Music Movie Speech Custom You can select the type of special sound effect to be used when watching a given broadcast i Move 4 Enter O PMODE SMODE STILL PSIZE gt You can select these options simply by pressing the l ESAVING _ PIP YIRE S MODE button on the remote control f 2 Equalizer Balance 100Hz 300Hz 1kHz 3kHz 10kHz The television has several settings which allow you to control the sound quality gt If you make any changes to these settings the sound mode j Moc aes Custom is automatically switched to Custom SRS TS XT Off SRS TS XT Off On Auto Volume Off TruSurround XT is a patented SRS technology that solves Sere ae the problem of playing 5 1 multichannel content over two speakers TruSurround delivers a compelling virtual surround sound experience through any two speaker playback system including internal television speakers It is fully compatible with Move e Enter O all multichannel formats 5 gt TruSurround XT SRSandc pot Equalizer Symbol are trademarks of SRS Labs SRS Inc TruSurround XT technology is incorporated under license from SRS 2 2 Labs Inc gt You can select these options simply by pressing the SRS HEE E ins eos button on the remote control Auto Volume Off On yMove 2 Adjust 5 Each broadcasting station has its own signal conditions and so it is not easy to adjust the volume every time the channelis J ja changed This fe
7. bright light in the room Choose Standard for general TV watching mode Choose Movie when viewing the movie English 17 Channel Country United Kingdom Auto Store gt Manual Store Channel Manager Sort Name Move Enter Return 4 gt Adjust C Save gt Return Piet Mono Picture Dynamic Sound Custom SRS TS XT Off Picture Mode Dynamic Contrast Brightness Sharpness Colour T Colour Tone Cool Size Auto Wide Screen Mode 16 9 Digital NR Y More Move C Enter Return Mode Contrast Brightness Sharpness Colour Colour Tone Coolt Size Auto Wide Screen Mode 16 9 Digital NR Auto Y More Move C Enter D Return PMODE SMODE STILL PSIZE ESAVIN SOURCE ___ 2 2 4 i a USIN DA SRS POSTION P M Customizing the Picture Settings Your television has several setting options that allow you to control the picture quality 1 2 3 4 N Picture Mode Dynamic Contrast Brightness Sharpness Colour Press the MENU button to display the menu Press the ENTER button to select Picture Press the ENTER button again to select Mode Select the required mode by pressing the A or Y button then press the ENTER button Colour Tone Coolt Size Auto Wide Screen Mode 16 9 Digital NR Auto A OO Gz Available modes Dynamic Standard Movie rise SEN Ski Select the required
8. lt or gt button until you reach the optimal setting Reset The previously adjusted colours will be reset to the factory defaults Edge Enhancement Off On You can emphasize object boundaries Colour Space Auto Wide You can set the colour reproduction space for the input signal to Auto or Wide English 19 Selecting the Picture Size You can select the picture size which best corresponds to your Picture viewing requirements j Mode Dynamic 1 Press the MENU button to display the menu Res 2 Press the ENTER button to select Picture Soe 3 Press the A or button to select Size then press the ENTER Co button 4 Select the required option by pressing the A or Y button then press the ENTER button Available options Auto Wide 16 9 Wide Zoom Zoom 4 3 SLE E S Just Scan Auto Wide Expanding and pulling up the picture from 4 3 7 to 16 9 ratio 16 9 16 9 Sets the picture to 16 9 wide mode Wide Zoom Wide Zoom Magnify the size of the picture more than 4 3 zoom Move the screen up down using the A or button after aa on selecting the l by pressing the gt or ENTER button Zoom Magnify the size of the picture vertically on screen 4 3 Sets the picture to 4 3 normal mode Just Scan Displays the input scenes as they are without any cutoff when HDMI 720p 1080i signals are input gt With the HDMI Just Scan picture size depending on the AV devices the screen may be cut off or a specific colour ap
9. set the DNle to Demo you can view the applied DNle and normal pictures on the screen for demonstration purposes Using this function you can view the difference in the visual quality gt DNle Digital Natural Image engine DNie This feature brings you more detailed image with 3D noise reduction detail enhancement contrast enhancement and white enhancement New image compensation Algorithm gives brighter clearer more detailed image to you DNle technology will fit every signal into your eyes gt This function is not available in PC mode gt This function is not available in Movie mode Move Y Enter Return Freezing the Current Picture You can freeze the picture when watching a television i programme simply by pressing the STILL button To return to STILL _PSIZE normal viewing press it again H gt This function will automatically cancel five minutes later i SOURC aes English 21 Sound Features oa Press the MENU button to display the menu fad im Sound Press the A or Y button to select Sound then press the Mode Custom ENTER button Eola Select the required option by pressing the A or V button then EATI press the ENTER button Internal nie Available options Mode Equalizer SRS TS XT Auto Volume E Internal Mute Sound Select Reset L When you are satisfied with your setting press the ENTER button Press the EXIT button to exit Mode
10. temperatures high humidity chemical substance and where it operates continually such as the airport the train station etc Failure to do so may cause a serious damage to your set 2007 Samsung Electronics Co Ltd All rights reserved English 2 Contents General Information User Instructions nnc 2 Checking Parts 4 Control Panel 5 Connection Panel 6 Viewing the Remote Control cece 8 Switching Your Television On and Off 9 Viewing the Menus 10 Plug amp Play Feature cee 10 Viewing an External Signal Sources 12 Editing Device Names ld Channel Control Storing Channels Automatically 0 0 0 0 13 Storing Channels Manually 14 Adding Locking Channels sal Sorting the Stored Channels ccceee 16 Assigning Names to Channels 0c 16 Fine Tuning Channel Reception 00 17 Picture Control Changing the Picture Standard cee 17 Customizing the Picture Settings 18 Configuring Detailed Settings on the Picture 19 Selecting the Picture Size eee Selecting the Screen Mode Digital NR Active Colour DNIe we Freezing the Current Picture cece A Press Symbols Sound Control Sound Features unero 22 Selecting the Sound Mode depending on the Model ceeeeeeeeees 23 Function Description Tie Features 202 ccisceuvitnrecanaiis 24 Lang
11. the broadcasting stations in your area have been assigned to position numbers from P00 to P99 You can select a channel by entering the position number in this mode C Air channel mode You can select a channel by entering the assigned number to each air broadcasting station in this mode S Cable channel mode You can select a channel by entering the assigned number for each cable channel in this mode English 14 Adding Locking Channels Using the Channel Manager you can conveniently lock or add DENEB channels 5 i Country United Kingdom 14 Press the MENU button to display the menu Hehe 2 gt 2 Pressthe A or Y button to select Channel then press the ChannelManager ENTER button acne 3 Press the A or W button to select Channel Manager then z Fine Tune press the ENTER button Adding channels Move amp Enter Return Using the Channel List you can add channels Channel Manager 4 Select Channel List by pressing the ENTER button Taa 5 Move to the 65 field by pressing the A lt gt buttons Child Lock Off gt select a channel to be added and press the ENTER button to add the channel gt Ifyou press the ENTER button again the W symbol next to the channel disappears and the channel is not added Locking channels This feature allows you to prevent unauthorized users such as children from watching unsuitable programmes by muting out Channel List video and audio 6 Press the A or Y b
12. M NICAM ae Mono Stereo NICAM Stereo stereo Normal NICAM NICAM Mono MORMONS dual 1 dual 2 Normal Regular broadcast Standard audio Mono Normal use Seo _Bilingual or DUAL N Dual ra Dual Il tereo Mono Stereo Stereo Forced mono gt Ifthe receiving conditions deteriorate listening will be easier if the mode is set to Mono Ifthe stereo signal is weak and automatic switching occurs switch to Mono English 23 Time Features 14 Press the MENU button to display the menu Press the A or Y button to select Setup then press the ENTER button 3 Press the A or Y button to select Time then press the ENTER Blue Screen button melody 4 Select the required option by pressing the A or Y button then pee Se Standby press the ENTER button Available options Clock Set Sleep Timer Timer 1 Timer 2 Timer 3 5 When you are satisfied with your setting press the ENTER Energy Saving i Off Y More Move Enter Return button a Clock Set 6 Press the EXIT button to exit Seep ai Clock Set Timer 2 You can set the television clock so that the current time is Timers displayed when pressing the INFO button on the remote control You must also set the time if you wish to use the automatic on or off timers Press the lt or gt button to select Month Day Year Hour Move Enter Return or Minute Set these by pressing the A or Y button gt You can set the Month Day Year Hour or Minute
13. TER BlackAdjust Off button Dynamic Contrast Off 6 Press the EXIT button to exit Y Whio Balance My Colour Control gt Detailed Settings is available in Standard or Movie mode LA Par E r If DNle is Off the Detailed Settings cannot be selected when 5 the Picture mode is in Standard mode Black Adjust Off Low Medium High Moea eE aReturn You can directly select the black level on the screen to adjust the screen depth Dynamic Contrast Off Low Medium High You can adjust the screen contrast so that the optimal contrast is provided Gamma 3 3 You can adjust the middle brightness of pictures Press the lt or gt button until you reach the optimal setting White Balance R Offset G Offset B Offset R Gain G Gain B Gain Reset You can adjust the color temperature for more natural picture colors R Offset G Offset B Offset R Gain G Gain B Gain Changing the adjustment value will refresh the adjusted screen Select the required option by pressing the A or Y button then press the ENTER button Press the lt or gt button until you reach the optimal setting Reset The previously adjusted white balance will be reset to the factory defaults My Colour Control Pink Green Blue White Reset This setting can be adjusted to suit your personal preferences Pink Green Blue White Changing the adjustment value will refresh the adjusted screen Select the required option by pressing the A or Y button then press the ENTER button Press the
14. Timer 4 directly by pressing the numeric buttons on the remote control gt In the event of a power interruption or the set being turned off at the supply the settings for the Clock will be lost Sleep Timer You can select a time period of between 30 and 180 minutes See after which the television automatically switches to standby na mode Adjust Return Select the preset time interval Off 30 60 90 120 150 or k a 180 for staying on by pressing the A or Y button i A NT NAZ i gt You can select these options simply by pressing the i IV CHUST SLEEP HDMI j SLEEP button on the remote control If the sleep timer is not yet set Off is displayed If it is already set the remaining time before which the television switches to standby mode is displayed Timer 1 Timer 2 Timer 3 You can set the On Off timers so that the television will switch on or off automatically at the time you select i RETURN INFOC TTX MIX You must set the clock first i i Press the lt or button to select the required item below IIL DNAN LMAO LSTIL 097k l t Press the A or V button to adjust to the setting satisfied On Time Select hour minute and No Yes To activate timer with the setting satisfied set to Yes Off Time Select hour minute and No Yes To activate timer with the setting satisfied set to Yes Repeat Select Once Everyday Mon Fri Mon Sat or Sat Sun Volume Select the required volume
15. act your nearest dealer English 27 Viewing the Picture in Picture PIP You can display a sub picture within the main picture In this way you can watch TV program or monitor the video input from ESA any connected devices HDMI Black v 14 Press the MENU button to display the menu Screen Burn Protection 2 Pressthe A or Y button to select Setup then press the ENTER button 3 Press the A or Y button to select PIP then press the ENTER button 4 Select the required option by pressing the A or Y button then AMV En Rtu press the ENTER button Available options PIP On Off Source Size Position Programme j _ Source 5 When you are satisfied with your setting press the ENTER Sie button m 6 Press the EXIT button to exit PIP On Off Table of PIP Settings Move Enter Return Main picture Sub picture uag Kaa Lad ao Analog TV broadcasts E J PC Ext 1 Ext 2 i rt JQ You can activate or deactivate the PIP function gt You can select these options simply by pressing the PIP button on the remote control Source TV Ext 1 Ext 2 You can select a source of the sub picture Size La You can select a size of the sub picture gt If main picture is in PC and Component mode Size is not available Position L E You can select a position of the sub picture Programme You can select a channel of the sub picture only wh
16. ature lets you automatically adjust the volume DUAL SRS POSTON P_ of the desired channel by lowering the sound output when the a J CYU tv modulation signal is high or by raising the sound output when the modulation signal is low Internal Mute Off On If you want to hear the sound through separate speakers cancel the internal amplifier gt The A and MUTE buttons do not operate when the Internal Mute is set to On Sound Select Main Sub When the PIP feature is activated you can listen to the sound of the sub PIP picture Main Used to listen to the sound of the main picture Sub Used to listen to the sound of the sub picture Reset Return TS G Return f 40kHz Return If Game Mode is On the Reset Sound function is activated Selecting the Reset function after setting the equalizer resets the equalizer setting to the factory defaults English 22 Selecting the Sound Mode depending on the model The DUAL l Il button displays controls the processing and output of the audio signal When power is switched on the mode is automatically preset to either DUAL I or Stereo depending on the current transmission JEJEJ DUAL SRS POSITION P EAN E Lx Type of broadcast On screen indication 1M amamma Regular broadcast Standard audio Mono Normabiiss Regular NICAM Mono NICAM Mono Normal NICA
17. ck that you have pressed the Power button On Off on the front panel or press the POWER button on the remote control Check the picture contrast and brightness settings Check the volume Check if Internal Mute is set to ON Normal picture but no sound Check the volume Check whether the volume MUTE button on the remote control has been pressed No picture or black and white picture Adjust the colour settings Check that the broadcast system selected is correct Sound and picture interference Try to identify the electrical appliance that is affecting the television then move it further away Plug the television into a different main socket Blurred or snowy picture distorted sound Check the direction location and connections of your aerial This interference often occurs due to the use of an indoor aerial Remote control malfunctions Replace the remote control batteries Clean the upper edge of the remote control transmission window Check that the and ends of the batteries are inserted correctly Check that the batteries are drained Screen is black and power indicator light blinks steadily On your computer check Power Signal Cable The TV is using its power management system Move the computer s mouse or press any key on the keyboard On your equipment check STB DVD etc Power Signal Cable The TV is using its power management system Press the Source button o
18. creen position and size will vary depending on the type of PC monitor and its resolution The table below shows all of the display modes that are supported i Vertical Horizontal z Video Resolution Vertical Horizontal Signal Dot X Line ae sl ae polarity polarity PS 42062H PS 50C62H 640 x 350 70 086 31 469 N P Y Y 720 x 400 70 087 31 469 P N Y Y 59 940 31 469 N N Y Y 70 000 35 000 N P N P Y Y 640x480 F 72809 37 861 N N Vv v 75 000 37 500 N N Y Y see bar 60 317 37 879 P P Y Y 70 000 43 750 N P N P Y A Compatible P 800x600 72188 48 077 P P Vv v 75 000 46 875 P P Y Y 60 004 48 363 N N Y Y 70 069 56 476 N N Y Y 1924x169 72 000 57 672 N P N P Y Y 75 029 60 023 P P Y Y 1360 x 768 60 015 47 712 P P A N Negative P Positive The interlace mode is not supported The television might operate abnormally if a non standard video format is selected 480i p 576i p 720p or 1080i is not available in PC mode For the PS 42C62H PC text quality is optimum in XGA mode 1024 x 768 60Hz For the PS 50C62H PC text quality is optimum in WXGA mode 1360 x 768 60Hz The three pixels each on the left and right are grayed at the resolution setting of 1360 x 768 60Hz This is not a mechanical problem but a result caused by the pixel difference between the standard resolution and the PDP panel eee English 31 Setting the PC gt Preset to the PC mode by pres
19. e gt Optimum condition for pixel shift Move Enter O Return PC TV Ext Component HDMI Horizontal Dot 1 2 Vertical Line 1 2 Time minute 2 min 2 min gt The Pixel Shift value may differ depending on the monitor size inches and mode All White This function helps remove after images on the screen by changing the colour of pixels to white Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time Signal Pattern This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time Side Gray When you watch TV with the screen ratio of 4 3 the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides Dark When you set the screen ratio to 4 3 it darkens the left and right sides Light When you set the screen ratio to 4 3 it brightens the left and right sides gt To remove after images on the screen use either All White or Signal Pattern function Although both of the two functions remove after images on the screen Signal Pattern is more effective gt The after image removal function has to be executed for a long time approximately 1 hour to effectively re
20. e batteries drained 4 Is there a power cut or is the power cord unplugged 5 Is there a special fluorescent light or a neon sign nearby Switching Your Television On and Off The main lead is attached to the rear of the television 1 2 Plug the main lead into an appropriate socket gt The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz Press the C Power button On Off on the front of the television or press the POWER button on the remote control to switch the television on The programme that you were watching last is re selected automatically If you have not yet stored any channels no clear picture appears Refer to Storing Channels Automatically on page 13 or Storing Channels Manually on page 14 gt Ifthe television is initially powered on several basic customer settings proceed automatically Refer to Plug amp Play Feature on page 10 To switch the television off press the C Power button On Off on the front of the television or press the POWER button on the remote control To switch the TV on press the Power button On Off on the front of the TV or press the POWER button or number buttons on the remote control English 9 Viewing the Menus 1 Press the MENU button The main menu is displayed on the screen Its left side has five icons Picture Sound Channel Setup and Input 2 Press the A or Y button to select one of the ico
21. en the Source is set to TV English 28 Screen Burn Protection To reduce the possibility of screen burn this unit is equipped with screen burn prevention technology This technology enables you to set picture movement up down Vertical Line ren IBI vel Low K and side to side Horizontal Dot The Time setting allows you to program the time between movement of the picture in minutes 14 Press the MENU button to display the menu 2 Press the A or Y button to select Setup then press the ENTER button Move Enter Return 3 Press the A or Y button to select Screen Burn Protection then press the ENTER button aa Sereen Bum Protection 4 Select the required option by pressing the A or Y button then All White press the ENTER button Signal Pattern Available options Pixel Shift All White Signal Pattern Side SIDE Gray y 5 When you are satisfied with your setting press the ENTER button z 6 Press the EXIT button to exit Move Enter O Return Pixel Shift Using this function you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after a image on the screen See Dot a Set Pixel Shift to On by pressing the A or V button then Vertical Line 2 press the ENTER button Time 2 Select the required option by pressing the A or Y button then press the ENTER button Available options Horizontal Dot Vertical Line Tim
22. gt You can select these options simply by pressing the SOURCE button on the remote control gt To watch television programme again press the TV button and select the channel number required English 12 Source List Edit Name Move Enter Return Source List Ext 1 Ext 2 Component Move C Enter Return TV CHLIST SLEEP HDMI ro Q Editing Device Names You can give a name to the external source Storing Channels Automatically Press the MENU button to display the menu Press the A or Y button to select Input then press the ENTER button Press the A or Y button to select Edit Name then press the ENTER button Press the A or Y button to select the external source to be edited then press the ENTER button Select the required device by pressing A or Y then press the ENTER button Available device names VCR DVD D VHS Cable STB HD STB Satellite STB AV Receiver DVD Receiver Game Camcorder DVD Combo DHR DVD HDD Recorder PC Press the EXIT button to exit Move Enter Return 4 lt Edit Name Ext Ext 2 3 l VCR Component DVD PC DHS _ Cable STB HDMI HDSTB Satellite STB AV Receiver v A SoN Move C Enter Return You can scan for the frequency ranges available to you Channel availability depends on your country Tea County Belgium Automatically allocated programme numbers may not Auto Store cea correspond t
23. hange channels In the on screen sources TV Ext 1 Ext 2 Component PC and menu use the W CIP V buttons as HDMI you use the A and buttons on the remote MENU control Press to see the on screen menu of your TV s ENTER features Press to confirm a selection m Power button Press to increase or decrease the volume Press to turn the TV on and off In the on screen menu use the ia buttons as you use the lt and gt buttons on the remote control Power Indicator Blinks and turns off when the power is on and lights up in stand by mode Remote Control Sensor Aim the remote control towards this spot on the TV Speaker English 5 Connection Panel Rear Panel OD or bbb bbe Cable Television Network C E 4 Whenever you connect an audio or video system to your set ensure that all elements are switched off When connecting an external device match the colour of the connection terminal to the cable POWER IN COMPONENT IN Connect the supplied power cord Audio AUDIO L R and video Y P8 PR inputs Connecting external Audio Devices for Component Connect RCA audio signals from the TV toan SERVICE external source such as Audio equipment
24. ical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal
25. ise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity This is normal and not a defect of the unit Cell Defects The PDP uses a panel consisting of 1 230 000 SD level to 3 150 000 HD level pixels which require sophisticated technology to produce However there may be few bright or dark pixels on the screen These pixels will have no impact on the performance of the product Avoid operating the TV at temperatures below 5 C 41 F Astill image displayed too long may cause permanent damage to the PDP Panel Watching the PDP TV in 4 3 format for a long period of time may leave traces of borders displayed on the left right and centre of the screen caused by the i difference of light emission on the screen Playing a DVD or a game console may cause similar effect to the screen Damages caused by the above effect are not covered by the Warranty After image on the Screen Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages To prevent this effect reduce the brightness and contrast when displaying still images Warranty Warranty does not cover any damage caused by image retention Burn in is not covered by the warranty Installation Be sure to contact an authorized service centre when installing your set in a location with heavy dust high or low
26. level Programme Select the required channel gt You can set the hour minute directly by pressing the number buttons on the remote control Auto Power Off When you set the timer On the TV will eventually turn off if no controls are operated for 3 hours after the TV was turned on by timer This function is only available in timer On mode and prevents overheating which may occur if a TV is on for too long time English 24 Language Blue Screen Melody Light Effect Energy Saving HDMI Black Level 14 Press the MENU button to display the menu Press the A or Y button to select Setup then press the 2 ENTER button gt 3 Select the required option by pressing the A or Y button then gt press the ENTER button k Available options Language Blue Screen Melody 5 Light Effect Energy Saving HDMI Black Level lt 4 When you are satisfied with your setting press the ENTER button Enter O Return 5 Press the EXIT button to exit Language It is variable depending on the model When you start using the television for the first time you must select the language which will be used for displaying menus and indications Blue Screen On Off If no signal is being received or the signal is very weak a blue screen automatically replaces the noisy picture background If you wish to continue viewing the poor picture you must set the Blue Screen to Off Melody Off Low Medium High The TV power on off
27. matically during the search and store operation If the signal is weak or distorted you may have to fine tune the channel manually 1 2 3 Press the MENU button to display the menu Press the A or Y button to select Channel then press the ENTER button Press the A or Y button to select Fine Tune then press the ENTER button To obtain a sharp and clear picture and good sound quality press the lt or gt button until you reach the optimal setting Press the ENTER button gt To reset the fine tuning to 0 select Reset by pressing the A or Y button Press the ENTER button Press the EXIT button to exit gt Fine Tune Store will change the colour of the Channel OSD On Screen Display from White to Red and add the mark Changing the Picture Standard You can select the type of picture which best corresponds to your viewing requirements 1 2 3 4 Press the MENU button to display the menu Press the ENTER button to select Picture Press the ENTER button again to select Mode Select the required mode by pressing the A or Y button then press the ENTER button Available modes Dynamic Standard Movie gt The settings values may vary depending on the input source ex TV Component PC or HDMI Press the EXIT button to exit gt You can select these options simply by pressing the P MODE button on the remote control gt Choose Dynamic for viewing the TV during the day or when there is
28. melody sound can be adjusted Light Effect Off ln Standby In Watching TV Always You can turn on off the blue LED on the front of TV according to the situation Use it for saving power or when the LED dazzles your eyes Off The blue LED is always off In Standby The blue LED lights while in Standby mode and it turns off when your TV is turned on In Watching TV The blue LED lights when watching TV and it turns off when your TV is turned off Always The blue LED always lights gt Set the Light Effect to Off to reduce the power consumption Energy Saving Off Low Medium High This feature adjusts the screen brightness depending on the surrounding lighting conditions Off Switches off the Energy Saving mode Low Operates in standard mode regardless of the surrounding illumination Medium Enters Medium power saving mode regardless of the surrounding illumination High Enters maximum power saving mode regardless of the surrounding illumination HDMI Black Level Normal Low Using this function you can adjust the image quality when the screen burn appearance of black level low contrast low color etc is encountered by the HDMI input for RGB limited range 16 to 235 gt This function is active only when the external input connects to HDMI RGB signals English 25 Using the Game Mode When connecting to a game console such as PlayStation or Xbox you can enjoy a more realistic gaming experience by 1 2 3
29. move after images on the screen If after image is not improved after the execution of the function repeat the function again gt Press any button on the remote control to cancel this feature English 29 Setting up Your PC Software Based on Windows XP The Windows display settings for a typical computer Display Properties are shown below But the actual screens on your PC will probably be different depending upon your particular version of Windows and your particular video card But even if your actual screens look different the same basic set up information will apply in almost all cases If not contact your computer manufacturer or Samsung Dealer Active Window EOR 14 Right click the mouse on the Windows Desktop then click on w Properties 4 The Display Properties will be displayed 2 Click on Settings tab then set the Display Mode with reference to the Display Modes Table You do not need to change the Colours settings 3 Click on Advanced A new settings dialog box will be displayed 4 Click on the Monitor tab then set the Screen refresh rate with reference to the Display Modes Table Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate 5 Click on OK to close the window then Click on OK button to the Display Properties window Automatic re booting may commence at this moment English 30 Input Mode PC Both s
30. n x Auto Adjustment Auto adjustment allows the PC screen of set to self adjust to the incoming PC video signal The values of fine coarse and position are adjusted Fl automatically v Image Reset You can replace all image settings with the factory default S Move 2 Enter D Return values Auto Adjustment in Progress Please wait Image Reset is completed English 32 Setting the Home Theatre PC You can view higher quality pictures by configuring the screen Setup settings in PC Mode Tg Plug amp Play 7 If you set the Home Theatre PC function to On you can moa Engien configure the Detailed Settings when Picture Mode is set to Game Mode Standard or Movie as in PC Mode p Miody 14 Press the MENU button to display the menu 2 Press the A or button to select Setup then press the Wall Mount Adjust ENTER button m Gneruy Saving 3 Press the A or button to select Home Theatre PC then Move Enter Return press the ENTER button 4 Select Off or On by pressing the A or Y button then press the ENTER button 5 Press the EXIT button to exit gt This function is available only in PC mode English 33 Teletext Feature depending on the model Most television stations provide written information services via teletext The index page of the teletext service gives you information on how to use the service In addition you can select various options to suit your requireme
31. n the panel or remote control Turn the TV off and on The damaged picture appears in the corner of the screen If Just Scan is selected in some external devices the damaged picture may appear in the corner of the screen This symptom is caused by external devices not TV Oe OF POOH OOO English 37 Specifications The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without notice Model Name PS 42C62H PS 50C62H eee 42 inch 50 inch PC Resolution 1024 x 768 60 Hz 1360 x 768 60 Hz Sound Output 10W 10W Dimension E 1055 x 713 x 95 mm 1227 x 802 x 96 mm ea 1055 x 757 x 340 mm 1227 x 845 x 341 mm Weight Body 31 kg 41 kg With stand 36 kg 46 kg Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity 10 C to 40 C 50 F to 104 F 10 to 80 non condensing 20 C to 45 C 4 F to 113 F 5 to 95 non condensing gt This device is a Class B digital apparatus Design and specifications are subject to change without prior notice For the power supply and Power Consumption refer to the label attached to the product English 38 This page is intentionally left blank This page is intentionally left blank This page is intentionally left blank This page is intentionally left blank Correct Disposal of This Product Waste Electr
32. ns Press the ENTER button to access the icon s sub menu 3 Press the A or Y button to move to items in the menu Press the ENTER button to enter items in the menu 4 Press the A lt gt button to change the selected items Press the RETURN button to return to the previous menu 5 Press the EXIT button to exit from the menu Plug amp Play Feature When the television is initially powered on several basic customer settings proceed automatically and subsequently The following settings are available If you accidentally select the wrong country for your TV the characters on the screen may be wrongly displayed 1 If the television is in standby mode press the POWER button on the remote control The message Start Plug amp Play is displayed Press the ENTER button 2 The Language menu will automatically appear after several seconds 3 Select the appropriate language by pressing the A or Y button Press the ENTER button The message Select Home Mode when installing this TV at home is displayed 4 Press the lt or gt button to select Shop or Home then press the ENTER button The message to check the connected status of the antenna is displayed gt The default selection is Home gt We recommend setting the TV to Home mode for the best picture in your home environment gt gt Shop mode is only intended for use in retail environments gt Ifthe unit is accidentally set to Shop mode and you want to
33. nts by using the remote i POWER son l control buttons H ON Coe For teletext information to be displayed correctly channel reception must be stable Otherwise information may be missing or some 2 pages may not be displayed O TV Exit from the teletext display depending on the model amp index OO ey Used to display the index contents page at any time while you H a e are viewing teletext i oo oR OROR reveal A Used to display the hidden text answers to quiz games for example To display normal screen press it again 43 hold Used to hold the display on a given page if the selected page is H linked with several secondary pages which follow on automatically To resume press it again i 5 mode Press to select the teletext mode LIST FLOF If you press it in the LIST mode it switches into the List save mode i In the List save mode you can save teletext page into list using the i store button ENET Ea sub page i ECE i Used to display the available sub page i Q page up SAMSUNE Used to display the next teletext page 8 page down Used to display the previous teletext page cancel Used to display the broadcast when searching for a page 10 S teletext on mix Press to activate teletext mode after selecting the channel providing the teletext service Press it twice to overlap the teletext with the current broadca
34. o actual or desired programme numbers adnan es Italy However you can sort numbers manually and clear any 7 Sort ea channels you do not wish to watch gt Name oe _ Switzerland 1 Press the MENU button to display the menu nied Kn 2 Press the A or Y button to select Channel then press the ENTER button Move Enter Return 3 Press the ENTER button again The available countries are listed Shane ___ 4 Select your country by pressing the A or Y button then press nee ss ee the ENTER button Manua Store 3 5 Press the A or Y button to select Auto Store then press the Sort ENTER button Namen 6 Press the ENTER button again to start the search The search will end automatically gt To stop the search before it has finished press the MENU 2 Move G2 Ene Retum or the ENTER button E Enter D Return English 13 Storing Channels Manually You can store television channels including those received via Channel cable networks Country United Kingdom When storing channels manually you can choose AutoStore gt Whether or not to store each of the channels found j The programme number of each stored channel which you wish Sort to identify Neme Fine Tune 14 Press the MENU button to display the menu Press the A or Y button to select Channel then press the ENTER button Move 4 Enter Return 3 Press the A or Y button to select Manual Store then press lt the ENTER bu
35. option by pressing the A or button then se press the ENTER button Picture When you are satisfied with your setting press the ENTER oct Dynamic puton oe Press the EXIT button to exit Colour Contrast Brightness Sharpness Colour Tint Detailed Set gt In TV mode of the PAL system you cannot use the Tint Brees Function Digital NR Contrast Brightness Colour Tone PC Mode Weve Enter O Return Press the lt or gt button until you reach the optimal setting Colour Tone Cool2 Cool1 Normal Warm1 Warm2 gt gt When the picture mode is set to Dynamic or Standard Warm1 and Warm2 cannot be selected Reset Cancel OK Select OK You can return to the factory defaults picture settings gt The reset function is set for each picture mode and colour tone English 18 Configuring Detailed Settings on the Picture You can set detailed picture settings 14 Press the MENU button to display the menu P Movie 2 Press the ENTER button to select Picture enone 3 Press the A or Y button to select Detailed Settings then Colour press the ENTER button Colour Tone 4 Select the required option by pressing the A or Y button then S Auto Wide press the ENTER button Fae o Available options Black Adjust Dynamic Contrast Gamma viie White Balance My Colour Control Edge Enhancement g Move ie Enter iO Retur Colour Space Detailed Settings 5 When you are satisfied with your setting press the EN
36. ote control Press the ENTER button to confirm your setting The message Enjoy your viewing is displayed When you have finished press the ENTER button gt Even if the ENTER button is not pressed the message will automatically disappear after several seconds gt Plug amp Play feature is available in the TV mode only If you want to reset this feature 1 2 3 Press the MENU button to display the menu Press the A or Y button to select Setup then press the ENTER button Press the ENTER button again to select Plug amp Play The message Start Plug amp Play is displayed English 11 Enter 1 Skip Plug amp Play Clock Set Month Day Year Hour Minute Cor o for A oo 4 gt Move Adjust Enter Enjoy your viewing Blue Screen Off Melody Medium Homa Thestrej me Light Effect In Standby Energy Saving Off Y More Move 4 Enter O Return Viewing an External Signal Sources You can switch between viewing signals from connected equipment such as a VCR DVD Set Top Box and the TV source broadcast or cable 14 Press the MENU button to display the menu 2 Press the A or Y button to select Input then press the ENTER s button 3 Press the ENTER button again to select Source List 4 Pressthe A or button to select the signal source then press the ENTER button Available signal sources TV Ext 1 Ext 2 Component PC HDMI
37. ount is used or the consumer fails to follow the product installation instructions gt Our 57 and 63 models do not comply with VESA Specifications Therefore you should use our dedicated wall mount kit for this model gt Do not exceed 15 degrees tilt when mounting this TV uN Do not install your Wall Mount Kit while your TV is turned on It may result in personal injury due to electric shock English 36 How to assemble the Stand Base depending on the model Using the 4 screws for securing the stand base and the monitor firmly attach the monitor to the stand base The exterior of the set may be different than the picture In case of installing your TV on the wall close the cover on the stand base connection part using two screws for hiding Warning i SS Firmly secure the stand to the TV i a before moving it as the stand may SS fall and could cause serious injury ke Te gt Two or more people should carry A T the TV Never lay the TV onthe oa LA floor because of possible damage 4G ay to the screen deel i Always store the TV upright o Troubleshooting Before contacting the Samsung after sales service perform the following simple checks If you cannot solve the problem using the instructions below note the model and serial number of the television and contact your local dealer No sound or picture Check that the mains lead has been connected to a wall socket Che
38. pears on the screen 5 Press the EXIT button to exit Move C Enter D gt Return ooo gt You can change the picture size simply by pressing the PORTO S OST P SIZE button on the remote control PMODE E STILL PSIZE gt gt Depending on the input source the picture size options J may vary ESAVING T gl gt The items available may differ depending on the selected l a J felle J i mode I IE EEE ES Positioning and Sizing the screen using Zoom Resizing the screen using the Zoom enables the positioning and sizing of the screen to up down direction using the A or Y button as well as the screen size Move the screen up down using the A or Y button after selecting the by pressing the lt or gt button Resize the screen vertically using the A or Y button after selecting the 1 by pressing the lt or gt button Selecting the Screen Mode When setting the picture size to Auto Wide in a 16 9 wide TV Picture you can determine the picture size you want to see the 4 3 Mode Dynamic gt WSS Wide Screen Service image or nothing Each individual SS SS European country requires different picture size so this amp Supe F function is intended for users to select it 14 Press the MENU button to display the menu 2 Press the ENTER button to select Picture 3 Press the A or Y button to select Screen Mode then press e the ENTER button G Enter Return 4 Select the required option by pressing
39. return to Dynamic Home mode press the Volume button and then hold down the MENU button for five seconds on the TV panel 5 Make sure that the antenna is connected to the TV Press the ENTER button The Country menu is displayed 6 Select your country or area by pressing the A or Y button Press the ENTER button The menu to select channels is displayed English 10 Picture Mode Dynamic Contrast Brightness Sharpness Colour Colour Tone Size Auto Wide Screen Mode 16 9 Digital NR Auto Y More Move Enter Exit RETURN INFO TTX MIX B i i i PMODE e STILL _PSIZE i oe E E aN a ly Start Plug amp Play Plug amp Play English Deutsch Fran ais LEENI Language Move Enter Skip Select Home Mode when installing this TV at home 4 gt Move Enter I Skip a Plug amp Play oo Check antenna input Plug amp Play A United Kingdom Austria Country Eastern Europe v Move Enter I Skip Continued 7 To start channel store press the ENTER button The search will end automatically The TV will begin memorizing all of the available channels Press the ENTER button to set the clock Press the lt gt ENTER button to select Month Day Year Hour or Minute Set these by pressing the A or Y button gt You can set the Month Day Year Hour or Minute directly by pressing the numeric buttons on the rem
40. sing the SOURCE button Setup 14 Press the MENU button to display the menu A Plug amp Pla hia 2 Press the A or Y button to select Setup then press the Times En ENTER button Siegen 3 Press the A or Y button to select PC then press the i ENTER button Light Effect i In Standby gt 4 Select the required option by pressing the A or V button then fSia smm n a Serr lt press the ENTER button Y More Available options Image Lock Position Auto Adjustment z Move O Ener O Retum Image Reset PC 5 When you are satisfied with your setting press the ENTER J button Position 6 Press the EXIT button to exit Eai Image Lock Coarse Fine The purpose of picture quality adjustment is to remove or reduce picture noise If the noise is not removed by Fine tuning alone then adjust the frequency as best as possible coarse and Fine tune again Move Enter Return After the noise has been reduced re adjust the picture so that it fi n Image Lock is aligned on the center of screen a 1 Press the A or Y button to select Coarse or Fine then el ine ae ee 63 press the ENTER button 2 Press the lt or gt button to adjust the screen quality vertical stripes may appear or the picture may be blurry Press the ENTER button Position Adjust the PC s screen positioning if it does not fit the TV screen Move Enter Return 1 Adjust the position by pressing the A lt gt button Position 2 Press the ENTER butto
41. ss the ENTER button 2 Press the A or button to select Wall Mount Adjustment then press the ENTER button 3 Adjust to the desired position using the A lt gt buttons Press the EXIT button to exit gt Ifyou press an arrow button when no OSD is displayed on the TV screen the Adjustment screen appears gt gt When you turn the power off your TV moves to the initial installation position When you turn the power on your TV moves to the last remembered position you adjusted Using the remote Control Buttons Button Operations os A Tilt Up Tilt Down Move adjustment right Move left No Moves to the initial Reset installation position Remembers 3 positions Tedeh ap d with the Red Green and PMODE SMODE STIL Poin to the Yellow buttons E d Moves to the remembered He position using these 3 color position buttons gt For installation refer to the Installation Manual provided Setup Plug amp Play Language English Time Game Mode Off Blue Screen Off Melody Medium Move Enter Return Wall Mount Adj ni Position1 A v Position 5 2 3 INFO ROT Cg J Exit a 3 lt gt Adjust gt gt For product installation and the installation and moving of the wall mount make sure to consult a specialized installation company gt This installation manual is to be used when attaching the wall mount to a wall When attaching to other building materials please cont
42. sting screen Coloured buttons red green yellow blue If the FASTEXT system is used by a broadcasting company the different topics covered on a teletext page are colour coded and can be selected by pressing the coloured buttons Press one of them corresponding to the required The page is displayed with other coloured information that can be selected in the same way To display the previous or next page press the corresponding coloured button store Used to store the teletext pages size Press to display the double size letters in the upper half of the screen For lower half of the screen press it again To display normal screen press it once again 8 gt You can change teletext pages by pressing the numeric buttons on the remote control i J i Tv AOST SEEP HOMI Continued English 34 The teletext pages are organized according to six categories Part Contents Selected page number Broadcasting channel identity Current page number or search indications Date and time Text Status information FASTEXT information TMmMOOWD gt Teletext information is often divided between several pages displayed in sequence which can be accessed by Entering the page number Selecting a title in a list Selecting a coloured heading FASTEXT system gt Press the TV button to exit from the teletext display English 35 TV CHLIST SLEEP HDMI
43. t in picture distortion image breakup or no picture Do not attempt to connect the HDMI DVI connector to a PC or Laptop Graphics Card This will result in a blank screen being displayed DVI IN AUDIO L R DVI audio outputs for external devices English 7 Viewing the Remote Control gt This is a special remote control for the visually impaired persons and has Braille points on the POWER Volume and Channel buttons OO OOOO 6060 OO 08006060 8 8 The performance of the remote control may be affected by bright light POWER button turns the TV on and off Number buttons for direct channel access One Two digit channel selection Channel control button Refer to page 15 Selects the TV mode directly Volume increase Volume decrease Displays the main on screen menu Temporary sound switch off Use to see information on the current broadcast Returns to the previous menu Sound effect selection Refer to page 22 Picture effect selection Refer to page 17 Adjusts screen brightness to save energy Sound mode selection Picture In Picture Off On TruSurround XT mode button Available source selection Previous channel Automatic Power off Selects the HDMI mode directly Next channel amp Previous channel Exit the on screen menu Change confirmation 26 27 29 D Move to the required menu option Adjust an option value respectively
44. ted accordingly Repeat steps 4 to 5 until you have moved all the channels to the required programme numbers Press the EXIT button to exit Assigning Names to Channels Channel names will be assigned automatically when channel information is broadcast These names can be changed allowing you to assign new names 1 2 3 Press the MENU button to display the menu Press the A or Y button to select Channel then press the ENTER button Press the A or Y button to select Name then press the ENTER button Press the A or Y button to select the channel to be assigned to a new name then press the ENTER button Press the A or Y button to select a letter a number or a symbol Results in this sequence A Z 0 9 blank Move on to the previous or next letter by pressing the lt or gt button then press the ENTER button Repeat steps 4 to 5 for each channel to be assigned to a new name Press the EXIT button to exit English 16 Channel Country United Kingdom Auto Store gt Manual Store Channel Manager Name Fine Tune Move Enter Return 4p LONDAN Enter O Return Channel Country United Kingdom Auto Store gt Manual Store Channel Manager Sort Fine Tune Move Enter Return 0 2 3 4 5 6 7 8 9 lt G Enter O Return Fine Tuning Channel Reception If the reception is clear you do not have to fine tune the channel as this is done auto
45. the A or Y button then press the ENTER button Available options 16 9 Wide Zoom Zoom 4 3 16 9 Sets the picture to 16 9 wide mode Wide Zoom Magnify the size of the picture more than 4 3 Zoom Magnify the size of the picture vertically on screen 4 3 Sets the picture to 4 3 normal mode When you are satisfied with your setting press the ENTER button 6 Press the EXIT button to exit a English 20 Digital NR Active Colour DNle 14 Press the MENU button to display the menu Picture Press the ENTER button to select Picture J Contrast Dynamic aa 3 Select the required option by pressing the A or Y button then Shee press the ENTER button Colour Available options Digital NR Active Colour DNle 4 When you are satisfied with your setting press the ENTER button 5 Press the EXIT button to exit Digital NR Off Low Medium High Auto If the signal received by the television is weak you can activate this feature to reduce any static and ghosting that may appear on the screen Active Colour Off On If you turn on this option the colours of the sky and grass will be stronger and clearer for a more vivid on screen picture gt This function is not available in PC mode gt This function is not available in Movie and Standard mode DNle Off Demo On This TV includes the DNle function so as to provide a high visual quality If you set DNle to on you can view the screen with the DNle feature activated If you
46. tton 4 Select the required option by pressing the A or Y button then Calour System Auto press the ENTER button Sond em 5 When you are satisfied with your setting press the ENTER r Search button Bea ee 6 Press the EXIT button to exit Programme Programme number to be assigned to a channel Press the A or V button until you find the correct number ou Moves Entec Return gt You can also select the channel number directly by pressing the numeric buttons 0 9 Colour System Auto PAL SECAM NTSC4 43 Press the A or Y button to select the required colour standard Sound System BG DK I L Press the A or button to select the required sound standard Channel When you know the number of the channel to be stored Press the A or Y button to select C Air channel or S Cable channel Press the button then press the A or Y button to select the required number gt You can also select the channel number directly by pressing the numeric buttons 0 9 gt If there is abnormal sound or no sound re select the sound standard required Search When you do not know the channel numbers Press the A or Y button to start the search The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen Store When you store the channel and associated programme number Set to OK by pressing the ENTER button Channel mode P Programme mode When completing tuning
47. uage Blue Screen Melody Light Effect Energy Saving HDMI Black Level isese 25 Using the Game Mode 26 Wall mount adjustment Sold separately 27 Viewing the Picture in Picture PIP Screen Burn Protection eooe PC Display Setting up Your PC Software Based on Windows XP 30 Input Mode PC ccc ccccweaceanniccan 31 Setting the PC ccesesscetcaninantseinwcnies 32 Setting the Home Theatre PC 33 Appendix Teletext Feature depending on the model 34 Wall Mount Kit Specifications VESA 36 How to assemble the Stand Base depending on the Model ceeseeeeees 37 Troubleshooting iis Specifications 0 cect gt Important Note English 3 Checking Parts e Owner s Instructions Remote Control Power Cord AAA Batteries A i Warranty Card Ferrite Core for Power Cord Registration Card Safety Guide Manual ZM i Component Cables Audio Cables PC Cable i I HDMI Cable gt Ferrite Core Power Cord The ferrite cores are used to shield the cables from interference When connecting a cable open the ferrite core and clip it around the cable near the plug English 4 Control Panel i Front or Side Panel aDunos ANNIN u A Q 3 S v OOOO OO Lal 1 SOURCE f O ACP OV Displays a menu of all of the available input Press to c
48. utton to select Child Lock then press the ENTER button 7 Select On by pressing the A or Y button then press the ENTER button 8 Press the A or Y button to select Channel List then press the ENTER button 9 Move to the fm field by pressing the A lt gt buttons select a channel to be locked and press the ENTER button Move C Enter D gt Return im Lock gt Ifyou press the ENTER button again the W symbol next to 5 Enter the channel disappears and the channel lock is canceled O Return gt Ablue screen is displayed when Child Lock is activated 10 Press the EXIT button to exit gt You can select these options simply by pressing the CH LIST i SS ee E button on the remote control i IM GULLIT SLEEP HDMI i Q LA SAL English 15 Sorting the Stored Channels This operation allows you to change the programme numbers of the stored channels This operation may be necessary after using the auto store 1 2 3 Press the MENU button to display the menu Press the A or Y button to select Channel then press the ENTER button Press the A or Y button to select Sort then press the ENTER button Select the channel that you wish to move by pressing the A or Y button then press the ENTER button Select the number of the programme to which the channel is to be moved by pressing the A or Y button Press the ENTER button The channel is moved to its new position and all other channels are shif
Download Pdf Manuals
Related Search