Samsung BN68-02617A-02 User's Manual
Contents
1. Connecting to a Local Area Network To enjoy watching streaming content from online providers such as You Tube and Blockbuster you must follow the steps below to connect the TV to your network Network Connection Wired There are two main ways to connect your TV to your network using cable depending on your network setup They are illustrated below External Modem ADSL VDSL Cable TV The Modem Port on the Wall TV Rear Panel Modem Cable LAN Cable The LAN Port on the Wall LAN Cable Most home networks use the Dynamic Host Configuration Protocol DHCP to configure network connections Home networks that support DHCP automatically provide the IP address subnet mask gateway and DNS values your TV needs to access the Internet so you don t have to enter them manually To configure your network connection for a network that uses DHCP follow these steps 1 Connect your TV to your network as shown in one of the illustrations above 2 Turn on your TV press the MENU button on your remote and then select Setup Network 3 Set the Network Type to Wired if it is not already set to Wired 4 Select Network Setup The Network Setup screen appears Network Setup Internet Protocol Setup Auto Auto E L L C Enter Return Move 5 Onthe Network Setup menu set Internet Protocol Setup and DNS to Auto Auto acquires and enters the necessary internet values automatically 6 Select2. batteries to the diagram in the battery compartment 3 Replace the cover Step 3 Connect Power and Antenna or Cable Connect ANT IN to e Wall cable jack or e VHF UHF Antenna or e Cable or Satellite box Ant or Cable Out Use a 75 ohm round cable Make sure the AC power cord is plugged in securely to the wall outlet and the TV Step 4 Connect External Devices Connecting an AV device Blu ray player cable satellite box etc eeccococococococococoocooococococococooocococsococooccococococococococococcoccocococococococooococococcocooococococococococococccoococococococococococoooccoocoocococococococococoococoococosococococococococococoococccoocococosococococoocoocoococococococoooocoooooooo For the very best picture quality select HD signal sources and use HDMI cables and connections Note that many digital cable programs are not in HD Check with your video provider to ensure your are receiving HD signals QSHEHEHEEHEEHEEEEEEEENH ae 5 ES Z N PC DVI AUDIO IN OACIA 7 a a a a ANIFA oaany oIan ection 480i only Using an Audio Video Cable VCR DVD Blu ray player Cable Box Satellite receiver VCR ATTA NAN SESS up to 1080p cocooscocooooo Connect your TV to your Home Theater or other audio Connecting an audio device secoooscoccosocococoososcooscoooococoosooococsoosocooococsoosocosococoocooooosoocosoc
3. button on your remote to move to the characters and the enter key to select them 7 Onthe Network Setup menu set Internet Protocol Setup and DNS to Auto The Auto acquires and enters the necessary internet values automatically 8 Select Network Test to check internet connectivity amp For more information see your user s manual Starting Internet TV PCC R SESH TEESE TSE HOHE TEESETOEE EOE ESESH EEL OEETEH TEE OEEEO ETHOS SEEE TEE HETOET EOE OHEESEESEEEOE ESET SETHE TE LESES OLE EEESEE EEE OEEEEE EDEN EEED To view the On Screen Menus follow these steps 1 Turn on your TV press the MENU button on your remote then select Application Content View 2 Press the lt or gt button to select Internet TV and the ENTERL4 button The USER TERMS and PRIVACY POLICY windows appears then select Yes 3 Follow the directions on your screen to set up Internet TV For detailed instructions see your Owner s Manual amp For best Internet TV results your broadband company should provide sustained download speeds of 3 5 mb sec or more BN68 02617A 02
4. press the POWER button on the remote or press the POWER button on the TV To run Plug amp Play follow these steps Plug amp Play Select Language of the OSD Language Move CC Enter 1 Onthe Language screen select the language for the On Screen Display OSD using your remote control and then press ENTER L button The Home Use screen appears 2 Select Home Use and then press ENTER button If you select Store Demo the TV will reset your picture and audio settings every 30 minutes After you press ENTER L button the Antenna Source screen appears 3 lf your TV is only attached to an antenna select Air If your TV is only attached to cable and you have no cable box select Cable If your TV is attached to an antenna and cable with no box select Auto When done press ENTERL button on your remote The Select Cable System screen appears IMPORTANT If your TV is attached to a cable or satellite box skip Steps 3 through 5 After Plug amp Play is complete set your TV to Channel 3 or 4 according to the directions for your cable or satellite box 4 lf your TV is attached to a cable system and you have no cable box you must select your cable system type If you have Digital cable you must select the cable system type for both Analog and Digital Engl After you have selected the cable system type select Start and then press the ENTERL button on your remote amp Most cable systems are Standard STD s
5. the clock To set the clock follow these steps 1 Turn on your TV 2 Using your remote press the Clock Set MENU button on your remote Then select Setup Time 3 Select Clock Mode and then press the ENTERL button Set Clock Mode to Manual amp Select Auto if you have a digital channel in your area and are not using a cable sat box 4 Select Clock Set and then press the ENTERL button The Clock Set screen appears 5 Using the number buttons on your remote enter the Month Day Year Hour and Minute Use the lt or gt button to move between entry fields 6 Press the RETURN button on your remote when done ear Hour Minute am pm ne S Ce Enter Return 4 gt Move amp Adjust Connecting a USB Device for Media Play COPS OOSOH SEES HHO HEE HOES EE ETOH OEE SHOES EE ESOOEEESESHEOEE OTST OSEEE SHOES EE TEHSETOTSOSHOETOOSEHSEEEOSOEHEEHOSSOOEEESSDETESHOSSOTESESESEEES You can enjoy photo music and movie files stored on a USB device by connecting it to the TV and using the Media Play feature To connect a USB device for Media Play follow these steps USB Drive 1 Turn on your TV 2 Connect a USB device containing photo music and or movie files to the USB1 HDD or USB2 jack on the side of the TV 3 When the Application selection screen appears press the ENTERL button on your remote to select Media Play USB E SUM A Change Device 5 View Devices 4 Enter 5 Retum
6. CONTENT TOOLS T ON OFF Turns the remote control light on and off When on the buttons become illuminated for a moment when pressed Using the remote control with this button set to off will reduce the battery usage time source i Return to the previous channel Cuts off the sound temporarily Change channels amp If your TV is attached to a cable or satellite box you change the channel using the box s remote MENU Displays the main on screen menu INTERNET Link to various internet services Ne Press to display information on the TV screen Exits the menu YAHOO Runs Yahoo widget 3D D Sets the 3D mode Le Controls recording on Samsung recorders with the Anynet feature Selecting a Source POPP S PSOE EEOC EEO OEEOEET EE EEEEO EEE EETEE TEE SETOEEEEEETETTEESETS EEO EEEHE EES ETETT EET ETOEE SEL OEEEH EET ENSEHE ESE EEE EEE HEED EOHEE EOE EOEES To watch a movie on your Blu ray player or watch your favorite TV show you must select the correct source A source is a device such as a Blu ray DVD player a cable satellite box antenna or a cable TV input Sources can be connected to your TV through the HDMI DVI Component Composite or D sub connections or through the Antenna or Cable In connections SOURCE To view the signal from a source connected to the HDMI DVI Component Composite or D sub jack press the SOURCE button on your remote Each time you press t
7. Network Test to check Internet connectivity amp Some networks are Static IP networks If your network is a Static IP network you can not use DHCP to configure the network connection Instead you must enter the IP Address Subnet Mask Gateway and DNS Server manually For instructions explaining how to configure a Static IP network see your user s manual English 2 Network Connection Wireless You can connect your TV to your LAN through a standard wireless router or modem To connect wirelessly you must first attach a Samsung Wireless LAN Adapter WISOSABGN WISOSABGN2 WIS1OABGN sold separately to either the USB1 HDD or USB2 port on the back of your TV See the illustration below TV Side Panel Samsung Wireless LAN Adapter Wireless IP sharer AP having DHCP Server F The LAN Port on the Wall Samsung Wireless LAN Adapter Samsung s Wireless LAN adapter supports the IEEE 802 11A IEEE 802 11B IEEE 802 11G and IEEE 802 11N wireless communication protocols For your TV to connect to your network the wireless router or modem you use must also support one of these protocols The fastest of these protocols is IEEE 802 11N Most wireless network systems incorporate a security system that requires devices that access the network through an access point or AP typically a wireless modem or router to transmit an encrypted security code called an access key For regular connections your TV is com
8. Quick Setup Guide Congratulations on the purchase of your new Samsung TV Read this setup guide to get your TV up and running quickly 1 800 SAMSUNG 1 800 726 7864 Samsung Electronics America Inc 85 Challenger Road Ridgefield Park NU 07660 2112 Samsung Electronics Canada Inc 55 Standish Court Mississauga Ontario L5R 4B2 Call Center hours of operation Mon Sun 9 00 AM 12 AM EST To register this product visit www samsung com register Getting Started Step 1 Install the Stand Follow the steps below to connect the TV to the stand STOP Please clo not return this unit If you have problems operating your TV call 1 800 SAMSUNG 1 800 726 7864 For web support please visit ww samsung com support amp Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them amp Make sure that at least two people lift and move the LCD TV amp Stand the product up and fasten the screws If you fasten the screws with the LCD TV placed down it may lean to one side s e 4 Bottom View bie of ie ae tt 1 p A aie Step 2 Install the Batteries into the Remote To install batteries into your remote control follow these steps 1 Lift the cover on the back of the remote upward as shown in the figure to the right 2 Install two AAA batteries amp Make sure to match the and ends of the
9. e you press the P SIZE button you change the size of the picture on the screen ish 1 i a Amplifier DVD Home Theater Using an Optical Cable Digital Audio System OPTICAL Using an HDMI Cable cs PC Using an D Sub Cable PC OUT AUDIO OUT fad O The following sizes are available Screen Fit Wide Fit 4 3 Standard screen amp Screen Fit displays a full HD picture covering the entire screen with no cutoff on any side It is only available when your TV inputs an HDMI 720p 1080i 1080p Component 1080 1080p or DTV over the air 1080i signal Changing the Picture Mode POC COOH EEEEOETE EEE HEHE EE OHOO ETE ETOTOT EES ETOO EEE OEHEOT COS ETS EE OEEHOHETOOTOHS EEO E ESHEETS OOTEHTEETOTSEHS EH OTETEEEEOESEOLEEEOEEOEESEOEDEEES Your TV has four preset Picture Modes with factory adjusted settings each designed to give you an excellent picture under specific conditions The Picture Modes are listed and described in the table below Brightens picture For a vibrant enhanced image in brightly lit or l Standard For a bright detailed picture in a normally lit room For a comfortable easy on the eyes picture in a normally lit room For a studio quality cinema picture in a dimly lit or dark room To change the Picture Mode follow these steps 1 With the TV on press the TOOLS button on your remote The Tools menu appears Using the A or on your remote select Pic
10. he SOURCE button you change to a different source Viewing the On Screen Menus POCO SOHO HSE HOES EEESOOE EEE OES O OO ESOSOEESHSOEOEESESOSE TES OSEEESESEHOESEESOOHEESEESHEET OES OHHSESOEEOESEEETOOT EES OEHOE EE EOOSEH ESE OESOEES To view the On Screen Menus follow these steps 1 With the power on press the MENU button on your remote The main menu appears The menu s left side has the following menu options Picture Sound Channel Setup Input Application and Support INTERNET TOOLS INFO 3 When done using the menu press the EXIT button on your remote to exit 2 Press the A or V button on your remote to select a menu option and then press the ENTERC button P SIZE Choose the picture size CC Controls the caption decoder POPP CCE EHE HEELS OEE HEETESTEHSEEEH EEE EEOEET EEE EEESER OE SOEET EEE SEEOEH TE EOOEH SEE TETEEE TEE ETEET EHS ETEOEE TE HSESOEELELEDET OEE SESEEE EEE EES You can change the channel and adjust the volume by using the CH and VOL buttons on the remote You can also change the channels by pressing the V CH A buttons on the front panel of your TV and adjust the volume by pressing the VOL buttons Power Indicator Remote control sensor Setting the Clock COCR COSHH TERETE HEL ETEE SET EEEEH HOE ESE OESEEE SEE EESEEE HE ETEESEHTEEETEE OEE TERSEH EHS ESEES ELS ESEHE HELE SEES ELE EESOEE EELS ESEE EEE ESOS Before you can use your TV s On Off Timer you must set
11. oooooososooococoocoocoosooooocoococooocoooosoocooocoooooooooo device to enjoy enhanced sound quality o connection Using an HDMI Cable Device Using an Audio Cable Device C k a 1 The HDMI connection carries digital video and audio DVD Blu Ray player HD Cable Box HD Satellite receiver STB Best Connection Using an DVI to HDMI Cable Device DVD Blu Ray player Cable Box Satellite receiver STB Very Good Connection 7 Using a Component Cable COMPONENT OUT VCR DVD Blu ray player Cable Box Satellite receiver H i aL IA gt Device 7 a I Good Connection amp When connecting to AV IN 1 on the back of your TV attach the video cable yellow to the green jack next to the AV IN 1 label The jack will not match the color of the video cable yellow Lowest Quality Connection Step S Run Plug amp Play When you turn on your TV for the first time it automatically launches the Plug amp Play function With Plug amp Play you can select the On Screen Display language set the clock mode and launch the TV s channel memorizing process It also displays connection instructions similar to those in this guide To navigate while Plug amp Play is running press the Up Down Left or Right arrow buttons on your remote To make a selection press the ENTERL button To skip a screen press the MENU button To turn on your TV
12. patible with the following security protocols Authentication Mode OPEN SHARED WPAPSK WPA2PSK Encryption Type WEP TKIP AES Configuring the Network Connection Wireless eococooocooooosooooooooo00000000000000000000000000000000000000000000000000000 0000o ooooooooosooooooooosooooooooosoosooooooooosoooooooooooo The instructions below are for networks that use the Dynamic Host Configuration Protocol DHCP to configure network connections automatically If your have a Static IP network see your user s manual for configuration instructions To configure your network connection for a network that uses DHCP follow these steps 1 Connect your TV to your network as shown in the illustrations above 2 Turn on your TV press the MENU button on your remote and the select Setup Network 3 Set the Network Type to Wireless if it is not already set to Wireless 4 Select Network Setup The Network Setup screen appears 5 Onthe Network Setup menu select an AP Access Point and ad hoc network if you have selected network with a security key the Security Key screen appears 6 Enter the Security Key using the numbers on the remote and then press the Blue button on your remote Network Setup Select a network Not Selected Internet Protocol Setup Auto amp Move Enter Return amp lf your network uses WEP security encryption 0 9 and A F will be available on the Security Key screen Use the Direction
13. ture mode On the Picture Mode menu use the lt or gt on your remote to select the Picture Mode you want 4 Press the EXIT button to exit the menu Remote Control Buttons and Functions POCO O OOOH ESET EEHEHOE EOE SHOH ETOH ESOS EE EHSOOHE SHOES TEESE E SESH ET EO SESOE SE ESOSH ETO OEEOEEEESHDETESHOEHE SES ESOSE EES ESHESEOSESOE SOOTHES 0000000000000000 EE HOSES OS ESOEE EES ESHES SO SESOE SEES OHH ES OSES EE ESTHET OS HOEHEE OOOOH EE SESSESE OSES EE ESTOS EES ESHEETS ESTO DEEEESESEEE OES SOES amp This is a special remote control for the visually impaired persons and has Braille points on the Power Channel Volume buttons Turns the TV on and off Press to switch between the sources Blu ray player cable box DVD player etc connected to your TV Press number buttons for direct access to channels Press to select additional digital channels broadcast by the same station For example to select channel 54 3 press 54 press and then press 3 Adjusts the volume Displays the channel list on the screen Displays the Content View which includes Channel List Internet TV Media Play AllShare and 3D Quickly selects frequently used functions Selects the on screen menu items and changes the values seen on the menu Return to the previous menu Colored buttons for use in the Channel List Internet TV Media Play menu etc Use these buttons in the Media Play and Anynet modes POWER O FHLIST
14. ystems If you are not sure about what kind of cable system you have contact your cable company 5 The TV memorizes the available channels This process can take up to 45 minutes After the TV has memorized the channels the Clock Mode screen appears 6 Choose the Clock Mode Select Auto if you have a digital channel in your area Select Manual if you don t or if you have a cable or satellite box When done press ENTER button The Daylight Savings screen appears amp If you select Manual the clock setting screen appears 7 Select the Daylight Saving Time setting Off On or Auto and then press ENTERL button 8 After the time zone screen The connection method for best HD screen quality is displayed Press Right arrow button on your remote to view each screen in succession Press the Blue button to skip this section 9 The Enjoy your TV screen appears and then press ENTER button Basic Functions Changing the Screen Size seccosococoscoescocsoosoocoosoosoosoocoocoocoocoscosooooccocosooooosoosoocoosooscoocoocoscoooosoooocoooosoocoosoocoocoosoocoocoocooocooocooooo Your TV has several screen size options each designed to work best with specific types of video input If you have a cable box or satellite receiver it may have its own set of screen sizes as well To change the screen size press the P SIZE button on your remote The first time you press it your TV displays the current setting Thereafter each tim
Download Pdf Manuals
Related Search